Commit 34539b442b ("bus: ti-sysc: Flush posted write on enable before
reset") caused a regression reproducable on omap4 duovero where the ISS
target module can produce interconnect errors on boot. Turns out the
registers are not accessible until after a delay for devices needing
a ti,sysc-delay-us value.
Let's fix this by flushing the posted write only after the reset delay.
We do flushing also for ti,sysc-delay-us using devices as that should
trigger an interconnect error if the delay is not properly configured.
Let's also add some comments while at it.
Fixes: 34539b442b ("bus: ti-sysc: Flush posted write on enable before reset")
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
The uarts should be tagged with SYSC_QUIRK_SWSUP_SIDLE instead of
SYSC_QUIRK_SWSUP_SIDLE_ACT. The difference is that SYSC_QUIRK_SWSUP_SIDLE
is used to force idle target modules rather than block idle during usage.
The SYSC_QUIRK_SWSUP_SIDLE_ACT should disable autoidle and wake-up when
a target module is active, and configure autoidle and wake-up when a
target module is inactive. We are missing configuring the target module
on sysc_disable_module(), and missing toggling of the wake-up bit.
Let's fix the issue to allow uart wake-up to work.
Fixes: fb685f1c19 ("bus: ti-sysc: Handle swsup idle mode quirks")
Tested-by: Dhruva Gole <d-gole@ti.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit feaa8baee8 ("bus: ti-sysc: Implement SoC revision handling")
created a list of SoC types searching for strings based on names
and wildcards which associates the SoC to different families.
The OMAP34xx and OMAP35xx are treated as SOC_3430 while
OMAP36xx and OMAP37xx are treated as SOC_3630, but the AM35xx
isn't listed.
The AM35xx is mostly an OMAP3430, and a later commit a12315d6d2
("bus: ti-sysc: Make omap3 gpt12 quirk handling SoC specific") looks
for the SOC type and behaves in a certain way if it's SOC_3430.
This caused a regression on the AM3517 causing it to return two
errors:
ti-sysc: probe of 48318000.target-module failed with error -16
ti-sysc: probe of 49032000.target-module failed with error -16
Fix this by treating the creating SOC_AM35 and inserting it between
the SOC_3430 and SOC_3630. If it is treaed the same way as the
SOC_3430 when checking the status of sysc_check_active_timer,
the error conditions will disappear.
Fixes: a12315d6d2 ("bus: ti-sysc: Make omap3 gpt12 quirk handling SoC specific")
Fixes: feaa8baee8 ("bus: ti-sysc: Implement SoC revision handling")
Signed-off-by: Adam Ford <aford173@gmail.com>
Message-ID: <20230906233442.270835-1-aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The am335x-evm started producing boot errors because of subtle timing
changes:
Unhandled fault: external abort on non-linefetch (0x1008) at 0xf03c1010
...
sysc_reset from sysc_probe+0xf60/0x1514
sysc_probe from platform_probe+0x5c/0xbc
...
The fix consists in using the appropriate sleep function in sysc reset.
For flexible sleeping, fsleep is recommended. Here, sysc delay parameter
can take any value in [0 - 255] us range. As a result, fsleep() should
be used, calling udelay() for a sysc delay lower than 10 us.
Signed-off-by: Julien Panis <jpanis@baylibre.com>
Fixes: e709ed70d1 ("bus: ti-sysc: Fix missing reset delay handling")
Message-ID: <20230821-fix-ti-sysc-reset-v1-1-5a0a5d8fae55@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The main change this time is the introduction of the drivers/genpd
subsystem that gets split out from drivers/soc to keep common
functionality together. Ulf Hansson is taking over maintainership for
these and is sending a separate pull request with the same commits,
but they are in the soc drivers tree to avoid conflicts against other
soc driver patches.
The SCMI driver subsystem gets an update to version 3.2 of the
specification. There are also updates to memory, reset and other firmware
drivers.
On the soc driver side, the updates are mostly cleanups across a number
of Arm platforms. On driver for loongarch adds power management for DT
based systems, another driver is for HiSilicon's Arm server chips with
their HCCS system health interface.
The remaining updates for the most part add support for additional
hardware in existing drivers or contain minor cleanups. Most of these
are for the Qualcomm Snapdragon platform.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEiK/NIGsWEZVxh/FrYKtH/8kJUicFAmTuWdMACgkQYKtH/8kJ
UicprBAAsvZ5h636MOwYasgK1bKnsWgj9yrBSzIf7VzKbBS5/QCrDSDek9oDvTBp
p6Rr+WC1RQl9i2DiRVSbEqkUS6X4hQF0kJdLudBwYuxBDf8ayzFzKAKk/ecsyoaC
0Rkeh4fCu1zVnQ2DZSPFJVRl01/oCr1ZtJ1W0UrXCslOSQy2987VqpJ/EQbaDLgb
3imxpvJNBscaKwcYRgxhcIMBLdGi3qXRE/TmAf1WMe8w6dfk5KmFiPPD7zxPTnFb
0fssdxgocjOkXEn6L1VdBMoTt4UQaU+xbnFsOsDA/F0EjR9ZLlhtwZxANv4GicP6
52FMFaxeXSUnpBelzuyRQpgnt9WW3ZbBGb9iaisTl1pwjC3PcN2noo8uFZk+kO6b
8q0fh4KVmD0QIupC4cfTsF4SGAQvnhko2ls9bt4FTF+z0COV3Ifs2cAggH+hn3yD
IziBrUUZrR4G8XhisJRQNZcRh1H/vVchcumqsxzCMhpXLWwdZ5vW85GCR/fAtQQT
woYgqFHXZjEko66bu2dtayr1dgmPvfbO6rXpUkIdeskY6XuKfZXuB93LkhsZ17LY
dfAaBLUebjMcpLrltCqyP1tUoqGyVOTJKxtB2MolHo/V/2JbKYmYHAMy+qX5I0Qm
UUbQDpHnkaQMTK2L/qvdfE4lgwWfFWX7lCK/AGa4ZBFl+Zl6DgE=
=xmHW
-----END PGP SIGNATURE-----
Merge tag 'soc-drivers-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"The main change this time was the introduction of the drivers/genpd
subsystem that gets split out from drivers/soc to keep common
functionality together.
The SCMI driver subsystem gets an update to version 3.2 of the
specification. There are also updates to memory, reset and other
firmware drivers.
On the soc driver side, the updates are mostly cleanups across a
number of Arm platforms. On driver for loongarch adds power management
for DT based systems, another driver is for HiSilicon's Arm server
chips with their HCCS system health interface.
The remaining updates for the most part add support for additional
hardware in existing drivers or contain minor cleanups. Most of these
are for the Qualcomm Snapdragon platform"
* tag 'soc-drivers-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (136 commits)
bus: fsl-mc: Use common ranges functions
soc: kunpeng_hccs: fix some sparse warnings about incorrect type
soc: loongson2_pm: add power management support
soc: dt-bindings: add loongson-2 pm
soc: rockchip: grf: Fix SDMMC not working on RK3588 with bus-width > 1
genpd: rockchip: Add PD_VO entry for rv1126
bus: ti-sysc: Fix cast to enum warning
soc: kunpeng_hccs: add MAILBOX dependency
MAINTAINERS: remove OXNAS entry
dt-bindings: interrupt-controller: arm,versatile-fpga-irq: mark oxnas compatible as deprecated
irqchip: irq-versatile-fpga: remove obsolete oxnas compatible
soc: qcom: aoss: Tidy up qmp_send() callers
soc: qcom: aoss: Format string in qmp_send()
soc: qcom: aoss: Move length requirements from caller
soc: kunpeng_hccs: fix size_t format string
soc: ti: k3-socinfo.c: Add JTAG ID for AM62PX
dt-bindings: firmware: qcom: scm: Updating VMID list
firmware: imx: scu-irq: support identifying SCU wakeup source from sysfs
firmware: imx: scu-irq: enlarge the IMX_SC_IRQ_NUM_GROUP
firmware: imx: scu-irq: add imx_scu_irq_get_status
...
Dhruva reported a build warning with W=1 for "Function parameter or member
'sysconfig' not described in 'sysc'". Let's document sysconfig to fix this.
Reported-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable the uart quirks similar to the earlier SoCs. Let's assume we are
likely going to need a k3 specific quirk mask separate from the earlier
SoCs, so let's not start changing the revision register mask at this point.
Note that SYSC_QUIRK_LEGACY_IDLE will be needed until we can remove the
need for pm_runtime_irq_safe() from 8250_omap driver.
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix "warning: cast from pointer to integer of different size" on 64-bit
builds.
Note that this is a cosmetic fix at this point as the driver is not yet
used for 64-bit systems.
Fixes: feaa8baee8 ("bus: ti-sysc: Implement SoC revision handling")
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The am335x devices started producing boot errors for resetting musb module
in because of subtle timing changes:
Unhandled fault: external abort on non-linefetch (0x1008)
...
sysc_poll_reset_sysconfig from sysc_reset+0x109/0x12
sysc_reset from sysc_probe+0xa99/0xeb0
...
The fix is to flush posted write after enable before reset during
probe. Note that some devices also need to specify the delay after enable
with ti,sysc-delay-us, but this is not needed for musb on am335x based on
my tests.
Reported-by: kernelci.org bot <bot@kernelci.org>
Closes: https://storage.kernelci.org/next/master/next-20230614/arm/multi_v7_defconfig+CONFIG_THUMB2_KERNEL=y/gcc-10/lab-cip/baseline-beaglebone-black.html
Fixes: 596e795569 ("bus: ti-sysc: Add support for software reset")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix warning drivers/bus/ti-sysc.c:1806 sysc_quirk_dispc()
warn: masking a bool.
While at it let's add a comment for what were doing to make
the code a bit easier to follow.
Fixes: 7324a7a0d5 ("bus: ti-sysc: Implement display subsystem reset quirk")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/linux-omap/a8ec8a68-9c2c-4076-bf47-09fccce7659f@kili.mountain/
Signed-off-by: Tony Lindgren <tony@atomide.com>
The double `the' is duplicated in the comment, remove one.
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Message-Id: <20220811121119.20288-1-wangborong@cdjrlc.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert list_for_each() to list_for_each_entry() where applicable.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Message-Id: <20220827094604.3325887-1-yangyingliang@huawei.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties. As
part of this, convert of_get_property/of_find_property calls to the
recently added of_property_present() helper when we just want to test
for presence of a property and nothing more.
Signed-off-by: Rob Herring <robh@kernel.org>
Message-Id: <20230310144734.1546656-1-robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
"ranges" is a standard property and we have common helper functions for
parsing it, so let's use them.
Signed-off-by: Rob Herring <robh@kernel.org>
Message-Id: <20230201220002.246907-1-robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
To prepare for probing omap3 musb with ti-sysc, these quirk flags are
needed similar to what we have for omap4.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Tested-by: Sicelo A. Mhlongo <absicsz@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Here is the large set of char, misc, and other driver subsystem updates
for 5.19-rc1. The merge request for this has been delayed as I wanted
to get lots of linux-next testing due to some late arrivals of changes
for the habannalabs driver.
Highlights of this merge are:
- habanalabs driver updates for new hardware types and fixes and
other updates
- IIO driver tree merge which includes loads of new IIO drivers
and cleanups and additions
- PHY driver tree merge with new drivers and small updates to
existing ones
- interconnect driver tree merge with fixes and updates
- soundwire driver tree merge with some small fixes
- coresight driver tree merge with small fixes and updates
- mhi bus driver tree merge with lots of updates and new device
support
- firmware driver updates
- fpga driver updates
- lkdtm driver updates (with a merge conflict, more on that
below)
- extcon driver tree merge with small updates
- lots of other tiny driver updates and fixes and cleanups, full
details in the shortlog.
All of these have been in linux-next for almost 2 weeks with no reported
problems.
Note, there are 3 merge conflicts when merging this with your tree:
- MAINTAINERS, should be easy to resolve
- drivers/slimbus/qcom-ctrl.c, should be straightforward
resolution
- drivers/misc/lkdtm/stackleak.c, not an easy resolution. This
has been noted in the linux-next tree for a while, and
resolved there, here's a link to the resolution that Stephen
came up with and that Kees says is correct:
https://lore.kernel.org/r/20220509185344.3fe1a354@canb.auug.org.au
I will be glad to provide a merge point that contains these resolutions
if that makes things any easier for you.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYpnkbA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylOrgCggbbAFwESBY9o2YfpG+2VOLpc0GAAoJgY1XN8
P/gumbLEpFvoBZ5xLIW8
=KCgk
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc / other smaller driver subsystem updates from Greg KH:
"Here is the large set of char, misc, and other driver subsystem
updates for 5.19-rc1. The merge request for this has been delayed as I
wanted to get lots of linux-next testing due to some late arrivals of
changes for the habannalabs driver.
Highlights of this merge are:
- habanalabs driver updates for new hardware types and fixes and
other updates
- IIO driver tree merge which includes loads of new IIO drivers and
cleanups and additions
- PHY driver tree merge with new drivers and small updates to
existing ones
- interconnect driver tree merge with fixes and updates
- soundwire driver tree merge with some small fixes
- coresight driver tree merge with small fixes and updates
- mhi bus driver tree merge with lots of updates and new device
support
- firmware driver updates
- fpga driver updates
- lkdtm driver updates (with a merge conflict, more on that below)
- extcon driver tree merge with small updates
- lots of other tiny driver updates and fixes and cleanups, full
details in the shortlog.
All of these have been in linux-next for almost 2 weeks with no
reported problems"
* tag 'char-misc-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (387 commits)
habanalabs: use separate structure info for each error collect data
habanalabs: fix missing handle shift during mmap
habanalabs: remove hdev from hl_ctx_get args
habanalabs: do MMU prefetch as deferred work
habanalabs: order memory manager messages
habanalabs: return -EFAULT on copy_to_user error
habanalabs: use NULL for eventfd
habanalabs: update firmware header
habanalabs: add support for notification via eventfd
habanalabs: add topic to memory manager buffer
habanalabs: handle race in driver fini
habanalabs: add device memory scrub ability through debugfs
habanalabs: use unified memory manager for CB flow
habanalabs: unified memory manager new code for CB flow
habanalabs/gaudi: set arbitration timeout to a high value
habanalabs: add put by handle method to memory manager
habanalabs: hide memory manager page shift
habanalabs: Add separate poll interval value for protocol
habanalabs: use get_task_pid() to take PID
habanalabs: add prefetch flag to the MAP operation
...
There are minor updates to SoC specific drivers for chips by Rockchip,
Samsung, NVIDIA, TI, NXP, i.MX, Qualcomm, and Broadcom. Noteworthy
driver changes include:
- Several conversions of DT bindings to yaml format.
- Renesas adds driver support for R-Car V4H, RZ/V2M and RZ/G2UL SoCs.
- Qualcomm adds a bus driver for the SSC (Snapdragon Sensor Core),
and support for more chips in the RPMh power domains and the soc-id.
- NXP has a new driver for the HDMI blk-ctrl on i.MX8MP.
- Apple M1 gains support for the on-chip NVMe controller, making it
possible to finally use the internal disks. This also includes SoC
drivers for their RTKit IPC and for the SART DMA address filter.
For other subsystems that merge their drivers through the SoC tree,
we have
- Firmware drivers for the ARM firmware stack including TEE, OP-TEE,
SCMI and FF-A get a number of smaller updates and cleanups. OP-TEE
now has a cache for firmware argument structures as an optimization,
and SCMI now supports the 3.1 version of the specification.
- Reset controller updates to Amlogic, ASpeed, Renesas and ACPI drivers
- Memory controller updates for Tegra, and a few updates for other
platforms.
-----BEGIN PGP SIGNATURE-----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=XoLF
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM driver updates from Arnd Bergmann:
"There are minor updates to SoC specific drivers for chips by Rockchip,
Samsung, NVIDIA, TI, NXP, i.MX, Qualcomm, and Broadcom.
Noteworthy driver changes include:
- Several conversions of DT bindings to yaml format.
- Renesas adds driver support for R-Car V4H, RZ/V2M and RZ/G2UL SoCs.
- Qualcomm adds a bus driver for the SSC (Snapdragon Sensor Core),
and support for more chips in the RPMh power domains and the
soc-id.
- NXP has a new driver for the HDMI blk-ctrl on i.MX8MP.
- Apple M1 gains support for the on-chip NVMe controller, making it
possible to finally use the internal disks. This also includes SoC
drivers for their RTKit IPC and for the SART DMA address filter.
For other subsystems that merge their drivers through the SoC tree, we
have
- Firmware drivers for the ARM firmware stack including TEE, OP-TEE,
SCMI and FF-A get a number of smaller updates and cleanups. OP-TEE
now has a cache for firmware argument structures as an
optimization, and SCMI now supports the 3.1 version of the
specification.
- Reset controller updates to Amlogic, ASpeed, Renesas and ACPI
drivers
- Memory controller updates for Tegra, and a few updates for other
platforms"
* tag 'arm-drivers-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (159 commits)
memory: tegra: Add MC error logging on Tegra186 onward
memory: tegra: Add memory controller channels support
memory: tegra: Add APE memory clients for Tegra234
memory: tegra: Add Tegra234 support
nvme-apple: fix sparse endianess warnings
soc/tegra: pmc: Document core domain fields
soc: qcom: pdr: use static for servreg_* variables
soc: imx: fix semicolon.cocci warnings
soc: renesas: R-Car V3U is R-Car Gen4
soc: imx: add i.MX8MP HDMI blk-ctrl
soc: imx: imx8m-blk-ctrl: Add i.MX8MP media blk-ctrl
soc: imx: add i.MX8MP HSIO blk-ctrl
soc: imx: imx8m-blk-ctrl: set power device name
soc: qcom: llcc: Add sc8180x and sc8280xp configurations
dt-bindings: arm: msm: Add sc8180x and sc8280xp LLCC compatibles
soc/tegra: pmc: Select REGMAP
dt-bindings: reset: st,sti-powerdown: Convert to yaml
dt-bindings: reset: st,sti-picophyreset: Convert to yaml
dt-bindings: reset: socfpga: Convert to yaml
dt-bindings: reset: snps,axs10x-reset: Convert to yaml
...
We can get "failed to disable" clock_unprepare warnings on unbind at least
for the serial console device if the unbind is done before the device has
been idled.
As some devices are using deferred idle, we must check the status for
pending idle work to idle the device.
Fixes: 76f0f772e4 ("bus: ti-sysc: Improve handling for no-reset-on-init and no-idle-on-init")
Cc: Romain Naour <romain.naour@smile.fr>
Reviewed-by: Romain Naour <romain.naour@smile.fr>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20220512053021.61650-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It does not make sense to have a comma after a sentinel, as any new
elements must be added before the sentinel.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Message-Id: <602f74030dc746eaa9f82f115acc46e62c6be165.1646311501.git.geert+renesas@glider.be>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On beagleboard revisions A to B4 we need to use gpt12 as the system timer.
However, the quirk handling added for gpt12 caused a regression for system
suspend for am335x as the PM coprocessor needs the timers idled for
suspend.
Let's make the gpt12 quirk specific to omap34xx, other SoCs don't need
it. Beagleboard revisions C and later no longer need to use the gpt12
related quirk. Then at some point, if we decide to drop support for the old
beagleboard revisions A to B4, we can also drop the gpt12 related quirks
completely.
Fixes: 3ff340e24c ("bus: ti-sysc: Fix gpt12 system timer issue with reserved status")
Reported-by: Kevin Hilman <khilman@baylibre.com>
Suggested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These are all the driver updates for SoC specific drivers. There
are a couple of subsystems with individual maintainers picking up
their patches here:
- The reset controller subsystem add support for a few new SoC
variants to existing drivers, along with other minor improvements
- The OP-TEE subsystem gets a driver for the ARM FF-A transport
- The memory controller subsystem has improvements for Tegra,
Mediatek, Renesas, Freescale and Broadcom specific drivers.
- The tegra cpuidle driver changes get merged through this
tree this time. There are only minor changes, but they depend
on other tegra driver updates here.
- The ep93xx platform finally moves to using the drivers/clk/
subsystem, moving the code out of arch/arm in the process.
This depends on a small sound driver change that is included
here as well.
- There are some minor updates for Qualcomm and Tegra specific
firmware drivers.
The other driver updates are mainly for drivers/soc, which contains
a mixture of vendor specific drivers that don't really fit elsewhere:
- Mediatek drivers gain more support for MT8192, with new support for
hw-mutex and mmsys routing, plus support for reset lines in the
mmsys driver.
- Qualcomm gains a new "sleep stats" driver, and support for
the "Generic Packet Router" in the APR driver.
- There is a new user interface for routing the UARTS on ASpeed
BMCs, something that apparently nobody else has needed so far.
- More drivers can now be built as loadable modules, in particular
for Broadcom and Samsung platforms.
- Lots of improvements to the TI sysc driver for better suspend/resume
support
Finally, there are lots of minor cleanups and new device IDs for
amlogic, renesas, tegra, qualcomm, mediateka, samsung, imx, layerscape,
allwinner, broadcom, and omap.
-----BEGIN PGP SIGNATURE-----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=tUuj
-----END PGP SIGNATURE-----
Merge tag 'drivers-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"These are all the driver updates for SoC specific drivers. There are a
couple of subsystems with individual maintainers picking up their
patches here:
- The reset controller subsystem add support for a few new SoC
variants to existing drivers, along with other minor improvements
- The OP-TEE subsystem gets a driver for the ARM FF-A transport
- The memory controller subsystem has improvements for Tegra,
Mediatek, Renesas, Freescale and Broadcom specific drivers.
- The tegra cpuidle driver changes get merged through this tree this
time. There are only minor changes, but they depend on other tegra
driver updates here.
- The ep93xx platform finally moves to using the drivers/clk/
subsystem, moving the code out of arch/arm in the process. This
depends on a small sound driver change that is included here as
well.
- There are some minor updates for Qualcomm and Tegra specific
firmware drivers.
The other driver updates are mainly for drivers/soc, which contains a
mixture of vendor specific drivers that don't really fit elsewhere:
- Mediatek drivers gain more support for MT8192, with new support for
hw-mutex and mmsys routing, plus support for reset lines in the
mmsys driver.
- Qualcomm gains a new "sleep stats" driver, and support for the
"Generic Packet Router" in the APR driver.
- There is a new user interface for routing the UARTS on ASpeed BMCs,
something that apparently nobody else has needed so far.
- More drivers can now be built as loadable modules, in particular
for Broadcom and Samsung platforms.
- Lots of improvements to the TI sysc driver for better
suspend/resume support"
Finally, there are lots of minor cleanups and new device IDs for
amlogic, renesas, tegra, qualcomm, mediateka, samsung, imx,
layerscape, allwinner, broadcom, and omap"
* tag 'drivers-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (179 commits)
optee: Fix spelling mistake "reclain" -> "reclaim"
Revert "firmware: qcom: scm: Add support for MC boot address API"
qcom: spm: allow compile-testing
firmware: arm_ffa: Remove unused 'compat_version' variable
soc: samsung: exynos-chipid: add exynosautov9 SoC support
firmware: qcom: scm: Don't break compile test on non-ARM platforms
soc: qcom: smp2p: Add of_node_put() before goto
soc: qcom: apr: Add of_node_put() before return
soc: qcom: qcom_stats: Fix client votes offset
soc: qcom: rpmhpd: fix sm8350_mxc's peer domain
dt-bindings: arm: cpus: Document qcom,msm8916-smp enable-method
ARM: qcom: Add qcom,msm8916-smp enable-method identical to MSM8226
firmware: qcom: scm: Add support for MC boot address API
soc: qcom: spm: Add 8916 SPM register data
dt-bindings: soc: qcom: spm: Document qcom,msm8916-saw2-v3.0-cpu
soc: qcom: socinfo: Add PM8150C and SMB2351 models
firmware: qcom_scm: Fix error retval in __qcom_scm_is_call_available()
soc: aspeed: Add UART routing support
soc: fsl: dpio: rename the enqueue descriptor variable
soc: fsl: dpio: use an explicit NULL instead of 0
...
Fix drivers/bus/ti-sysc.c:2494:13: error: variable 'error' set but not
used introduced by commit 9d88136120 ("bus: ti-sysc: Add quirk handling
for reinit on context lost").
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 94f6345712 ("bus: ti-sysc: Implement quirk handling for
CLKDM_NOAUTO") should have also added the quirk for dra7 dcan1 in
addition to dcan2 for errata i893 handling.
Let's also pass the quirk flag for legacy mode booting for if "ti,hwmods"
dts property is used with related dcan hwmod data. This should be only
needed if anybody needs to git bisect earlier stable trees though.
Fixes: 94f6345712 ("bus: ti-sysc: Implement quirk handling for CLKDM_NOAUTO")
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is no need for the legacy flag any longer for gpio as the omap-sham
driver has been fixed to not rely on pm_runtime_irq_safe().
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is no need for the legacy flag any longer for gpio as the gpio-omap
driver has been fixed to not rely on pm_runtime_irq_safe().
Signed-off-by: Tony Lindgren <tony@atomide.com>
Let's add handling the otg force idle quirk for the old omap2430 glue layer
used up to omap4 as the musb driver quirk only works if the driver is
loaded. Unlike with the am335x glue layer, looks like we don't need the
quirk handling for SYSC_QUIRK_REINIT_ON_CTX_LOST.
Eventually when all the musb using SoCs are booting with device tree based
configuration, we can just remove the related quirk handling from the
musb driver.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Let's use SYSC_QUIRK_REINIT_ON_CTX_LOST quirk for am335x otg instead of
SYSC_QUIRK_REINIT_ON_RESUME quirk as we can now handle the context loss
in a more generic way.
Signed-off-by: Tony Lindgren <tony@atomide.com>
At least on am335x, the gpmc module needs a re-init and reset if context
has been lost on resume. We can enable this for all gpmc revisions as we
check if the context was lost before restoring it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
At least am335x gpmc module needs a reset in addition to re-init on resume.
Let's add a quirk handling for reset on re-init.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some interconnect target modules such as otg and gpmc on am335x need a
re-init after resume. As we also have PM runtime cases where the context
may be lost, let's handle these all with cpu_pm.
For the am335x resume path, we already have cpu_pm_resume() call
cpu_pm_cluster_exit().
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is no need to restore context if it was not lost. Let's add a new
function sysc_check_context() to check for lost context. To make use of it,
we need to save the sysconfig register status on enable and disable.
Signed-off-by: Tony Lindgren <tony@atomide.com>
On resume we can get a warning at kernel/time/timekeeping.c:824 for
timekeeping_suspended.
Let's fix this by adding separate functions for sysc_poll_reset_sysstatus()
and sysc_poll_reset_sysconfig() and have the new functions handle also
timekeeping_suspended.
If iopoll at some point supports timekeeping_suspended, we can just drop
the custom handling from these functions.
Fixes: d46f9fbec7 ("bus: ti-sysc: Use optional clocks on for enable and wait for softreset bit")
Signed-off-by: Tony Lindgren <tony@atomide.com>
These are updates for drivers that are tied to a particular SoC,
including the correspondig device tree bindings:
- A couple of reset controller changes for unisoc, uniphier, renesas
and zte platforms
- memory controller driver fixes for omap and tegra
- Rockchip io domain driver updates
- Lots of updates for qualcomm platforms, mostly touching their
firmware and power management drivers
- Tegra FUSE and firmware driver updateѕ
- Support for virtio transports in the SCMI firmware framework
- cleanup of ixp4xx drivers, towards enabling multiplatform
support and bringing it up to date with modern platforms
- Minor updates for keystone, mediatek, omap, renesas.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iD8DBQBhLz215t5GS2LDRf4RAjlHAJ473D0PymaTzv68EuPHThG+DEPifQCdGjLq
QGBB6JidIP8rtEdC+LWBB8I=
=M5+N
-----END PGP SIGNATURE-----
Merge tag 'drivers-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"These are updates for drivers that are tied to a particular SoC,
including the correspondig device tree bindings:
- A couple of reset controller changes for unisoc, uniphier, renesas
and zte platforms
- memory controller driver fixes for omap and tegra
- Rockchip io domain driver updates
- Lots of updates for qualcomm platforms, mostly touching their
firmware and power management drivers
- Tegra FUSE and firmware driver updateѕ
- Support for virtio transports in the SCMI firmware framework
- cleanup of ixp4xx drivers, towards enabling multiplatform support
and bringing it up to date with modern platforms
- Minor updates for keystone, mediatek, omap, renesas"
* tag 'drivers-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (96 commits)
reset: simple: remove ZTE details in Kconfig help
soc: rockchip: io-domain: Remove unneeded semicolon
soc: rockchip: io-domain: add rk3568 support
dt-bindings: power: add rk3568-pmu-io-domain support
bus: ixp4xx: return on error in ixp4xx_exp_probe()
soc: renesas: Prefer memcpy() over strcpy()
firmware: tegra: Stop using seq_get_buf()
soc/tegra: fuse: Enable fuse clock on suspend for Tegra124
soc/tegra: fuse: Add runtime PM support
soc/tegra: fuse: Clear fuse->clk on driver probe failure
soc/tegra: pmc: Prevent racing with cpuilde driver
soc/tegra: bpmp: Remove unused including <linux/version.h>
dt-bindings: soc: ti: pruss: Add dma-coherent property
soc: ti: Remove pm_runtime_irq_safe() usage for smartreflex
soc: ti: pruss: Enable support for ICSSG subsystems on K3 AM64x SoCs
dt-bindings: soc: ti: pruss: Update bindings for K3 AM64x SoCs
firmware: arm_scmi: Use WARN_ON() to check configured transports
firmware: arm_scmi: Fix boolconv.cocci warnings
soc: mediatek: mmsys: Fix missing UFOE component in mt8173 table routing
soc: mediatek: mmsys: add MT8365 support
...
After commit a6d90e9f22 ("bus: ti-sysc: AM3: RNG is GP only"), clang
with -Wimplicit-fallthrough enabled warns:
drivers/bus/ti-sysc.c:2958:3: warning: unannotated fall-through between
switch labels [-Wimplicit-fallthrough]
default:
^
drivers/bus/ti-sysc.c:2958:3: note: insert 'break;' to avoid
fall-through
default:
^
break;
1 warning generated.
Clang's version of this warning is a little bit more pedantic than
GCC's. Add the missing break to satisfy it to match what has been done
all over the kernel tree.
Fixes: a6d90e9f22 ("bus: ti-sysc: AM3: RNG is GP only")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We have changed the return type for sysc_check_active_timer() from -EBUSY
to -ENXIO, but the gpt12 system timer fix still checks for -EBUSY. We are
also not returning on other errors like we did earlier as noted by
Pavel Machek <pavel@denx.de>.
Commit 3ff340e24c ("bus: ti-sysc: Fix gpt12 system timer issue with
reserved status") should have been updated for commit 65fb736761
("bus: ti-sysc: suppress err msg for timers used as clockevent/source").
Let's fix the issue by checking for -ENXIO and returning on any other
errors as suggested by Pavel Machek <pavel@denx.de>.
Fixes: 3ff340e24c ("bus: ti-sysc: Fix gpt12 system timer issue with reserved status")
Depends-on: 65fb736761 ("bus: ti-sysc: suppress err msg for timers used as clockevent/source")
Reported-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Pavel Machek (CIP) <pavel@denx.de>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For the smartreflex device, we need to disable smartreflex on SoC idle,
and have been using pm_runtime_irq_safe() to do that. But we want to
remove the irq_safe usage as PM runtime takes a permanent usage count
on the parent device with it.
In order to remove the need for pm_runtime_irq_safe(), let's gate
the clock directly in the driver. This removes the need to call PM runtime
during idle, and allows us to switch to using CPU_PM in the following
patch.
Note that the smartreflex interconnect target module is configured for smart
idle, but the clock does not have autoidle capability, and needs to be gated
manually. If the clock supported autoidle, we would not need to even gate
the clock.
With this change, we can now remove the related quirk flags for ti-sysc
also.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
The McASP module in OMAP4 does not work if the SIDLE mode is enabled, most
like due to module integration issue that the signaling is not working
correctly.
Add a quirk for the module to select only NOIDLE mode when it is in use.
Suggested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Make the RNG on AM3 GP only.
Based on this patch from TI v5.4 tree which is based on hwmod data
which are now removed:
| ARM: AM43xx: hwmod: Move RNG to a GP only links table
|
| On non-GP devices the RNG is controlled by the secure-side software,
| like in DRA7xx hwmod we should not control this IP when we are not
| a GP device.
|
| Signed-off-by: Andrew F. Davis <afd@ti.com>
Cc: stable@vger.kernel.org # v5.10+
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Using pm_runtime_resume_and_get is more appropriate
for simplifing code.
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes the following W=1 kernel build warning(s):
drivers/bus/ti-sysc.c:867: warning: expecting prototype for syc_ioremap(). Prototype was for sysc_ioremap() instead
Cc: Tony Lindgren <tony@atomide.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Jarkko Nikula <jarkko.nikula@bitmer.com> reported that Beagleboard
revision c2 stopped booting. Jarkko bisected the issue down to
commit 6cfcd5563b ("clocksource/drivers/timer-ti-dm: Fix suspend
and resume for am3 and am4").
Let's fix the issue by tagging system timers as reserved rather than
ignoring them. And let's not probe any interconnect target module child
devices for reserved modules.
This allows PM runtime to keep track of clocks and clockdomains for
the interconnect target module, and prevent the system timer from idling
as we already have SYSC_QUIRK_NO_IDLE and SYSC_QUIRK_NO_IDLE_ON_INIT
flags set for system timers.
Fixes: 6cfcd5563b ("clocksource/drivers/timer-ti-dm: Fix suspend and resume for am3 and am4")
Reported-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like the swsup_sidle_act quirk handling is unreliable for serial
ports. The serial ports just eventually stop idling until woken up and
re-idled again. As the serial port not idling blocks any deeper SoC idle
states, it's adds an annoying random flakeyness for power management.
Let's just switch to swsup_sidle quirk instead like we already do for
omap3 uarts. This means we manually idle the port instead of trying to
use the hardware autoidle features when not in use.
For more details on why the serial ports have been using swsup_idle_act,
see commit 66dde54e97 ("ARM: OMAP2+: hwmod-data: UART IP needs software
control to manage sidle modes"). It seems that the swsup_idle_act quirk
handling is not enough though, and for example the TI Android kernel
changed to using swsup_sidle with commit 77c34c84e1e0 ("OMAP4: HWMOD:
UART1: disable smart-idle.").
Fixes: b4a9a7a389 ("bus: ti-sysc: Handle swsup idle mode quirks")
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Ivan Jelincic <parazyd@dyne.org>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Sicelo A. Mhlongo <absicsz@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On am335x, suspend and resume only works once, and the system hangs if
suspend is attempted again. However, turns out suspend and resume works
fine multiple times if the USB OTG driver for musb controller is loaded.
The issue is caused my the interconnect target module losing context
during suspend, and it needs a restore on resume to be reconfigure again
as debugged earlier by Dave Gerlach <d-gerlach@ti.com>.
There are also other modules that need a restore on resume, like gpmc as
noted by Dave. So let's add a common way to restore an interconnect
target module based on a quirk flag. For now, let's enable the quirk for
am335x otg only to fix the suspend and resume issue.
As gpmc is not causing hangs based on tests with BeagleBone, let's patch
gpmc separately. For gpmc, we also need a hardware reset done before
restore according to Dave.
To reinit the modules, we decouple system suspend from PM runtime. We
replace calls to pm_runtime_force_suspend() and pm_runtime_force_resume()
with direct calls to internal functions and rely on the driver internal
state. There no point trying to handle complex system suspend and resume
quirks via PM runtime.
This is issue should have already been noticed with commit 1819ef2e2d
("bus: ti-sysc: Use swsup quirks also for am335x musb") when quirk
handling was added for am335x otg for swsup. But the issue went unnoticed
as having musb driver loaded hides the issue, and suspend and resume works
once without the driver loaded.
Fixes: 1819ef2e2d ("bus: ti-sysc: Use swsup quirks also for am335x musb")
Suggested-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Naresh Kamboju <naresh.kamboju@linaro.org> reported that Beaglebone-X15
does not detect sata drives any longer after dra7 was flipped to boot with
device tree data only. Turns out we are now missing the sata related quirk
flags in ti-sysc that we used to have earlier.
Fixes: 98feab31ac ("ARM: OMAP2+: Drop legacy platform data for dra7 sata")
Fixes: 21206c8f2c ("ARM: OMAP2+: Drop legacy platform data for omap5 sata")
Link: https://lore.kernel.org/regressions/CA+G9fYtTN6ug3eBAW3wMcDeESUo+ebj7L5HBe5_fj4uqDExFQg@mail.gmail.com/
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Tested-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
