Currently we call function hisi_sas_debugfs_exit() to remove debugfs_dir
before freeing interrupt irqs and destroying workqueue in the driver remove
path.
If a dump is triggered before function hisi_sas_debugfs_exit() but
debugfs_work may be called after it, so it may refer to already removed
debugfs_dir which will cause NULL pointer dereference.
To avoid it, put function hisi_sas_debugfs_exit() after free_irqs and
destroy workqueue when removing hisi_sas driver.
Link: https://lore.kernel.org/r/1573551059-107873-4-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Need to return directly if init hardware failed.
Fixes: 73a4925d15 ("scsi: hisi_sas: Update all the registers after suspend and resume")
Link: https://lore.kernel.org/r/1573551059-107873-3-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The number of phy down reflects the quality of the link between SAS
controller and disk. In order to allow the user to confirm the link quality
of the system, we record the number of phy down for each phy.
The user can check the current phy down count by reading the debugfs file
corresponding to the specific phy, or clear the phy down count by writing 0
to the debugfs file.
Link: https://lore.kernel.org/r/1571926105-74636-19-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Although if the debugfs initialization fails, we will delete the debugfs
folder of hisi_sas, but we did not consider the scenario where debugfs was
successfully initialized, but the probe failed for other reasons. We found
out that hisi_sas folder is still remain after the probe failed.
When probe fail, we should delete debugfs folder to avoid the above issue.
Link: https://lore.kernel.org/r/1571926105-74636-18-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When injecting 2bit ecc errors, it will cause confusion inside SAS
controller which needs host reset to recover it. If a device is gone at the
same times inject 2bit ecc errors, we may not receive the ITCT interrupt so
it will wait for completion in clear_itct_v3_hw() all the time. And host
reset will also not occur because it can't require hisi_hba->sem, so the
system will be suspended.
To solve the issue, use wait_for_completion_timeout() instead of
wait_for_completion(), and also don't mark the gone device as
SAS_PHY_UNUSED when device gone.
Link: https://lore.kernel.org/r/1571926105-74636-4-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If set the BIST init value after enabling BIST, there may be still some few
error bits. According to the process, need to set the BIST init value
before enabling BIST.
Fixes: 97b151e758 ("scsi: hisi_sas: Add BIST support for phy loopback")
Link: https://lore.kernel.org/r/1571926105-74636-3-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add BIST (built in self test) support for phy loopback.
Through the new debugfs interface, the user can configure loopback
mode/linkrate/phy id/code mode before enabling it. And also user can
enable/disable BIST function.
Link: https://lore.kernel.org/r/1567774537-20003-13-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some function arguments are unused, so remove them.
Also move the timeout print in for wait_cmds_complete_timeout_vX_hw()
callsites into that same function.
Link: https://lore.kernel.org/r/1567774537-20003-11-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the NCQ tag is only assigned for FPDMA READ and FPDMA WRITE
commands, and for other NCQ commands (such as FPDMA SEND), their NCQ tags
are set in the delivery command to 0.
So for all the NCQ commands, we also need to assign normal NCQ tag for
them, so drop the command type check in hisi_sas_get_ncq_tag() [drop
hisi_sas_get_ncq_tag() altogether actually], and always use the ATA command
NCQ tag when appropriate.
Link: https://lore.kernel.org/r/1567774537-20003-8-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After suspend and resume, the HW registers will be set back to their
initial value. We use init_reg_v3_hw() to set some registers, but some
registers are set via firmware in ACPI "_RST" method, so add reset handler
before init_reg_v3_hw().
Link: https://lore.kernel.org/r/1567774537-20003-7-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The format specifier "%p" can leak kernel address, and use "%pK" instead.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove some unnecessary code, including:
- Explicit zeroing of memory allocated for dmam_alloc_coherent()
- Some duplicated code
- Some redundant masking
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It will free irq automatically if devm_request_irq() failed, so drop
free_irq() if devm_request_irq() failed.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The SMP frame response is written to the command table and not the SMP
response pointer from libsas, so don't bother DMA mapping (and unmapping)
the SMP response from libsas.
Suggested-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The call to kmap_atomic() in the SMP command completion code is
unnecessary, since kmap() is only really concerned with highmem, which is
not relevant on arm64. The controller only finds itself in arm64 systems.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The AXI and RAS register values should also should be snapshot at debugfs.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The value of IOST/ITCT is updated to cache first, and then synchronize to
DDR periodically. So the value in IOST/ITCT cache is the latest data and
it's important for debugging.
So, the HW cache of IOST and ITCT should be snapshot at debugfs.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In commit 1273d65f29 ("scsi: hisi_sas: change queue depth from 512 to
4096"), the depth of each queue is the same as the max IPTT in the system.
As such, as long as we have an IPTT allocated, we will have enough space on
any delivery queue.
All .get_free_slot functions were checking for space on the queue by
reading the DQ read pointer. Drop this, and also raise the code into common
code, as there is nothing hw specific remaining.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a small optimisation to be had by making the max IPTT the same for
all hw revisions, that being we can drop the check for read and write
pointer being the same in the get free slot function.
Change v1 hw to have max IPTT of 4096 - same as v2 and v3 hw - and
drop hisi_sas_hw.max_command_entries.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly update of the usual drivers: qla2xxx, hpsa, lpfc, ufs,
mpt3sas, ibmvscsi, megaraid_sas, bnx2fc and hisi_sas as well as the
removal of the osst driver (I heard from Willem privately that he
would like the driver removed because all his test hardware has
failed). Plus number of minor changes, spelling fixes and other
trivia.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXSTl4yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishdcxAQDCJVbd
fPUX76/V1ldupunF97+3DTharxxbst+VnkOnCwD8D4c0KFFFOI9+F36cnMGCPegE
fjy17dQLvsJ4GsidHy8=
=aS5B
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: qla2xxx, hpsa, lpfc, ufs,
mpt3sas, ibmvscsi, megaraid_sas, bnx2fc and hisi_sas as well as the
removal of the osst driver (I heard from Willem privately that he
would like the driver removed because all his test hardware has
failed). Plus number of minor changes, spelling fixes and other
trivia.
The big merge conflict this time around is the SPDX licence tags.
Following discussion on linux-next, we believe our version to be more
accurate than the one in the tree, so the resolution is to take our
version for all the SPDX conflicts"
Note on the SPDX license tag conversion conflicts: the SCSI tree had
done its own SPDX conversion, which in some cases conflicted with the
treewide ones done by Thomas & co.
In almost all cases, the conflicts were purely syntactic: the SCSI tree
used the old-style SPDX tags ("GPL-2.0" and "GPL-2.0+") while the
treewide conversion had used the new-style ones ("GPL-2.0-only" and
"GPL-2.0-or-later").
In these cases I picked the new-style one.
In a few cases, the SPDX conversion was actually different, though. As
explained by James above, and in more detail in a pre-pull-request
thread:
"The other problem is actually substantive: In the libsas code Luben
Tuikov originally specified gpl 2.0 only by dint of stating:
* This file is licensed under GPLv2.
In all the libsas files, but then muddied the water by quoting GPLv2
verbatim (which includes the or later than language). So for these
files Christoph did the conversion to v2 only SPDX tags and Thomas
converted to v2 or later tags"
So in those cases, where the spdx tag substantially mattered, I took the
SCSI tree conversion of it, but then also took the opportunity to turn
the old-style "GPL-2.0" into a new-style "GPL-2.0-only" tag.
Similarly, when there were whitespace differences or other differences
to the comments around the copyright notices, I took the version from
the SCSI tree as being the more specific conversion.
Finally, in the spdx conversions that had no conflicts (because the
treewide ones hadn't been done for those files), I just took the SCSI
tree version as-is, even if it was old-style. The old-style conversions
are perfectly valid, even if the "-only" and "-or-later" versions are
perhaps more descriptive.
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (185 commits)
scsi: qla2xxx: move IO flush to the front of NVME rport unregistration
scsi: qla2xxx: Fix NVME cmd and LS cmd timeout race condition
scsi: qla2xxx: on session delete, return nvme cmd
scsi: qla2xxx: Fix kernel crash after disconnecting NVMe devices
scsi: megaraid_sas: Update driver version to 07.710.06.00-rc1
scsi: megaraid_sas: Introduce various Aero performance modes
scsi: megaraid_sas: Use high IOPS queues based on IO workload
scsi: megaraid_sas: Set affinity for high IOPS reply queues
scsi: megaraid_sas: Enable coalescing for high IOPS queues
scsi: megaraid_sas: Add support for High IOPS queues
scsi: megaraid_sas: Add support for MPI toolbox commands
scsi: megaraid_sas: Offload Aero RAID5/6 division calculations to driver
scsi: megaraid_sas: RAID1 PCI bandwidth limit algorithm is applicable for only Ventura
scsi: megaraid_sas: megaraid_sas: Add check for count returned by HOST_DEVICE_LIST DCMD
scsi: megaraid_sas: Handle sequence JBOD map failure at driver level
scsi: megaraid_sas: Don't send FPIO to RL Bypass queue
scsi: megaraid_sas: In probe context, retry IOC INIT once if firmware is in fault
scsi: megaraid_sas: Release Mutex lock before OCR in case of DCMD timeout
scsi: megaraid_sas: Call disable_irq from process IRQ poll
scsi: megaraid_sas: Remove few debug counters from IO path
...
Many times in libsas, and in LLDDs which use libsas, the check for an
expander device is re-implemented or open coded.
Use dev_is_expander() instead. We rename this from
sas_dev_type_is_expander() to not spill so many lines in referencing.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For v3 hw, stash is enabled to promote performance, but it does little to
improve performance according to current tests. What's more, it causes
exceptions for some situations, so disable it.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Several error codes will be generated between PHY down to up.
This issue was introduced by HW design. The designers came to the
conclusion that we should ignore these errors.
Signed-off-by: Jiaxing Luo <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It reports a error as follows from some tools at two places in our code:
runtime error: left shift of 4 by 29 places cannot be represented in type
'int' So change the type of the two numbers to unsigned to avoid the error.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The argument of dev_err() called by multi_bit_ecc_error_process_v3_hw() is
not right. We pass two arguments, but there is only one printk format
specifier in the string.
Also move the print format string to dev_err().
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do some minor tidy-up.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch is to switch HW all error handling from PCI AER to MSI interrupt
due to non-standard PCI implementation. All HW errors which were being
reported through PCI AER can be reported through MSI interrupt also.
Do two things to complete the switch:
1. Notify FW to switch to MSI handling through ACPI DSM.
2. Add MSI handling for some hw errors, ECC errors and poison errors (we
also call some of them AXI reuser error). They were handled only through
PCI AER before.
For old FW reporting PCI AER events, the PCI AER handler will see that the
driver on longer support AER, and will leave the device in offlined state,
which is safe.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In commit 8b8d665315 ("scsi: hisi_sas: make SAS address of SATA disks
unique"), we ensured that each SATA disk in the system has a unique SAS
address, even if it is fake. That was for v2 hw.
Add this for v3 hw.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In commit efdcad62e7 ("scsi: hisi_sas: Set PHY linkrate when
disconnected"), we use the sas_phy_data.enable flag to track whether the
PHY was enabled or not, so that we know if we should set the PHY negotiated
linkrate at SAS_LINK_RATE_UNKNOWN or SAS_PHY_DISABLED.
However, it is not proper to use sas_phy_data.enable, since it is only set
when libsas attempts to set the PHY disabled/enabled; hence, it may not
even have an initial value.
As a solution to this problem, introduce hisi_sas_phy.enable to track
whether the PHY is enabled or not, so that we can set the negotiated
linkrate properly when the PHY comes down.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add host reset interface to make it easier for testing the host reset
feature.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is the final round of mostly small fixes and performance
improvements to our initial submit. The main regression fix is the
ia64 simscsi build failure which was missed in the serial number
elimination conversion.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXIxBayYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pisherpAP4rxLpX
bcUnQnEsvoxys/JyoK08Qfv1JebZo1B2MAZ62wD/VZ7LpOuzVLhsM2KhLFGRrs1/
7D2K4tgtO2dQsFix7H0=
=pcHl
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"This is the final round of mostly small fixes and performance
improvements to our initial submit.
The main regression fix is the ia64 simscsi build failure which was
missed in the serial number elimination conversion"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (24 commits)
scsi: ia64: simscsi: use request tag instead of serial_number
scsi: aacraid: Fix performance issue on logical drives
scsi: lpfc: Fix error codes in lpfc_sli4_pci_mem_setup()
scsi: libiscsi: Hold back_lock when calling iscsi_complete_task
scsi: hisi_sas: Change SERDES_CFG init value to increase reliability of HiLink
scsi: hisi_sas: Send HARD RESET to clear the previous affiliation of STP target port
scsi: hisi_sas: Set PHY linkrate when disconnected
scsi: hisi_sas: print PHY RX errors count for later revision of v3 hw
scsi: hisi_sas: Fix a timeout race of driver internal and SMP IO
scsi: hisi_sas: Change return variable type in phy_up_v3_hw()
scsi: qla2xxx: check for kstrtol() failure
scsi: lpfc: fix 32-bit format string warning
scsi: lpfc: fix unused variable warning
scsi: target: tcmu: Switch to bitmap_zalloc()
scsi: libiscsi: fall back to sendmsg for slab pages
scsi: qla2xxx: avoid printf format warning
scsi: lpfc: resolve static checker warning in lpfc_sli4_hba_unset
scsi: lpfc: Correct __lpfc_sli_issue_iocb_s4 lockdep check
scsi: ufs: hisi: fix ufs_hba_variant_ops passing
scsi: qla2xxx: Fix panic in qla_dfs_tgt_counters_show
...
This is mostly update of the usual drivers: arcmsr, qla2xxx, lpfc,
hisi_sas, target/iscsi and target/core. Additionally Christoph
refactored gdth as part of the dma changes. The major mid-layer
change this time is the removal of bidi commands and with them the
whole of the osd/exofs driver and filesystem.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXIC54SYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishT1GAPwJEV23
ExPiPsnuVgKj49nLTagZ3rILRQcYNbL+MNYqxQEA0cT8FHzSDBfWY5OKPNE+RQ8z
f69LpXGmMpuagKGvvd4=
=Fhy1
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: arcmsr, qla2xxx, lpfc,
hisi_sas, target/iscsi and target/core.
Additionally Christoph refactored gdth as part of the dma changes. The
major mid-layer change this time is the removal of bidi commands and
with them the whole of the osd/exofs driver and filesystem. This is a
major simplification for block and mq in particular"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (240 commits)
scsi: cxgb4i: validate tcp sequence number only if chip version <= T5
scsi: cxgb4i: get pf number from lldi->pf
scsi: core: replace GFP_ATOMIC with GFP_KERNEL in scsi_scan.c
scsi: mpt3sas: Add missing breaks in switch statements
scsi: aacraid: Fix missing break in switch statement
scsi: kill command serial number
scsi: csiostor: drop serial_number usage
scsi: mvumi: use request tag instead of serial_number
scsi: dpt_i2o: remove serial number usage
scsi: st: osst: Remove negative constant left-shifts
scsi: ufs-bsg: Allow reading descriptors
scsi: ufs: Allow reading descriptor via raw upiu
scsi: ufs-bsg: Change the calling convention for write descriptor
scsi: ufs: Remove unused device quirks
Revert "scsi: ufs: disable vccq if it's not needed by UFS device"
scsi: megaraid_sas: Remove a bunch of set but not used variables
scsi: clean obsolete return values of eh_timed_out
scsi: sd: Optimal I/O size should be a multiple of physical block size
scsi: MAINTAINERS: SCSI initiator and target tweaks
scsi: fcoe: make use of fip_mode enum complete
...
With default value of register SERDES_CFG, the link is not stable for some
special disks when running IO. According to HW guys' suggestion, need to
make the bit10~19 value of register SERDES_CFG the max value to increase
the reliability of the HiLink.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: Yupeng Zhou <zhouyupeng1@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The later revision of v3 hw has added an function of interrupt coalesce
according to time for PHY RX errors. We set the coalesce time to 1s. Then
we print PHY RX errors count when PHY RX errors happen, and don't need to
worry that there may be too much log prints.
Besides, we use hisi_sas_phy.lock to protect error count value. Because we
update them by calling phy_get_events_v3_hw(), which is also used by core
driver (for get PHY events function).
We relocate phy_get_events_v3_hw() to avoid a further declaration.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
According to the tool fortify, phy_up_v3_hw() returns signed value, while
it should return an unsigned value.
So change variable "res" from int to irq_return_t.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The change to use dma_set_mask_and_coherent() incorrectly made a second
call with the 32 bit DMA mask value when the call with the 64 bit DMA
mask value succeeded.
[mkp: fixed commit message]
Fixes: e4db40e7a1 ("scsi: hisi_sas: use dma_set_mask_and_coherent")
Cc: <stable@vger.kernel.org>
Suggested-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Do some very minor tidy-up, for things like needlessly initing variable and
not leaving whitespace before quote endings.
Originally-from: Xiang Chen <chenxiang66@hisilicon.com>
Originally-from: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For auto-control irq affinity mode, choose the dq to deliver IO according
to the current CPU.
Then it decreases the performance regression that fio and CQ interrupts are
processed on different node.
For user control irq affinity mode, keep it as before.
To realize it, also need to distinguish the usage of dq lock and sas_dev
lock.
We mark as experimental due to ongoing discussion on managed MSI IRQ
during hotplug:
https://marc.info/?l=linux-scsi&m=154876335707751&w=2
We're almost at the point where we can expose multiple queues to the upper
layer for SCSI MQ, but we need to sort out the per-HBA tags performance
issue.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To support queue mapped to a CPU, it needs to be ensured that issuing an
internal abort is safe, in that it is guaranteed that an internal abort is
processed for a single IO or a device after all the relevant command(s)
which it is attempting to abort have been processed by the controller.
Currently we only deliver commands for any device on a single queue to
solve this problem, as we know that commands issued on the same queue will
be processed in order, and we will not have a scenario where the internal
abort is racing against a command(s) which it is trying to abort.
To enqueue commands on queue mapped to a CPU, choosing a queue for an
command is based on the associated queue for the current CPU, so this is
not safe for internal abort since it would definitely not be guaranteed
that commands for the command devices are issued on the same queue.
To solve this issue, we take a bludgeoning approach, and issue a separate
internal abort on any queue(s) relevant to the command or device, in that
we will be guaranteed that at least one of these internal aborts will be
received last in the controller.
So, for aborting a single command, we can just force the internal abort to
be issued on the same queue as the command which we are trying to abort.
For aborting all commands associated with a device, we issue a separate
internal abort on all relevant queues. Issuing multiple internal aborts in
this fashion would have not side affect.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds support for DIX to v3 hw driver.
For this, we build upon support for DIF, most significantly is adding new
DMA map and unmap paths.
Some pre-existing macro precedence issues are also tidied. They were
detected by checkpatch --strict.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A NULL-pointer dereference was introduced for TMF SSP commands from the
upstreaming reworking.
Fix this by relocating the scsi_get_prot_op() callsite.
Fixes: d6a9000b81 ("scsi: hisi_sas: Add support for DIF feature for v2 hw")
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hot-plugging SAS wire of direct hard disk backplane may cause disk lost. We
have done this test with several types of SATA disk from different venders,
and only two models from Seagate has this problem, ST4000NM0035-1V4107 and
ST3000VM002-1ET166.
The root cause is that the disk doesn't send D2H frame after OOB finished.
SAS controller will issue phyup interrupt only when D2H frame is received,
otherwise, will be waiting there all the time.
When this issue happen, we can find the disk again with link reset. To fix
this issue, we setup an timer after OOB finished. If the PHY is not up in
20s, do link reset. Notes: the 20s is an experience value.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In function hisi_sas_alloc(), parameter shost is not used, so remove it.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When injecting 2 bit ECC error, it will cause fatal AXI interrupts. Before
the recovery of SAS controller reset, the internal of SAS controller is in
error. If CQ interrupts return at the time, actually it is exception CQ
interrupt, and it may cause resource release in disorder.
To avoid the exception situation, shutdown AXI bus after fatal AXI
interrupt. In SAS controller reset, it will restart AXI bus. For later
version of v3 hw, hardware will shutdown AXI bus for this situation, so
just fix current ver of v3 hw.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Send primitive NOTIFY to SSP situation only, or it causes underflow issue
when sending IO. Also rename hisi_sas_hw.sl_notify() to hisi_sas_hw.
sl_notify_ssp().
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently we set the protection parameters after calling scsi_add_host()
for v3 hw.
They should be set beforehand, so make this change.
Appearantly this fixes our DIX issue (not mainline yet) also, but more
testing required.
Fixes: d6a9000b81 ("scsi: hisi_sas: Add support for DIF feature for v2 hw")
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch create debugfs file for port register and add file operations.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch create debugfs file for global register and add file
operations.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
