Implement driver_name to provide an alternative to card_name for userspace
configuration of Amlogic audio cards.
Suggested-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20211017160028.23318-1-christianshewitt@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Up to now aic32x4_remove() returns zero unconditionally. Make it return
void instead which makes it easier to see in the callers that there is
no error to handle.
Also the return value of i2c and spi remove callbacks is ignored anyway.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20211015071113.2795767-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Do nothing if format was zero at snd_soc_runtime_set_dai_fmt().
soc-core.c can be more simple code by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87ee8jt7d3.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
DAI active count is not exchanged during for_each_rtd_dais()
loops. We don't need to keep snd_soc_dai_stream_active() as
"active" on soc_pcm_hw_clean(). This patch avoid verbose code.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87ilxvt7e6.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
soc_pcm_hw_clean() is using "continue" during for_each_rtd_dais(),
but it is very verbose. This patch cleanup it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87k0ibt7ej.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In cases where both rx and tx lrck are synced to the same source,
the resets for rx and tx need to be triggered simultaneously,
according to the downstream driver.
As there is no reset API to atomically bulk (de)assert two resets
at once, what the driver did was implement half a reset controller
specific to Rockchip, which tried to write the registers for the
resets within one write ideally or several writes within an irqsave
section.
This of course violates abstractions quite badly. The driver should
not write to the CRU's registers directly.
In practice, for the cases I tested the driver with, which is audio
playback, replacing the synchronised asserts with just individual
ones does not seem to make any difference.
If it turns out that this breaks something in the future, it should
be fixed through the specification and implementation of an atomic
bulk reset API, not with a CRU hack.
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Message-Id: <20211016105354.116513-2-frattaroli.nicolas@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Hi Mark
We already have Audio-Graph-Card which is Of-Graph base general sound
card driver. Basically it supports basic CPU-Codec connection, and is
also supporting DPCM connection. Because it was forcibly expanded to
DPCM, DT parsing is very limited and very difficult to add new features
on it, for example Multi-CPU/Codec support, Codec2Codec support, etc.
This patch adds more flexible new Audio-Graph-Card2 driver for it.
Audio-Graph-Card and Audio-Graph-Card2 are similar, but don't have
full compatibility.
The reason why I need Audio-Graph-Card2 instead of updating Audio-Graph-Card
is that it is very difficult to keep compatibility.
Audio-Graph-Card2 supports Normal/DPCM/Codec2Codec Connection wich
Single/Multi DAIs. And it is possible to Customizing.
This patch-set adds Audio-Graph-Card2 driver and its custom driver
sample, and DT settings sample which can be used for testing.
To enable testing/debuging, this patch-set also adds Test-Component
driver. We already have Dummy Component and/or Dummy DAI on soc-utils,
but 1) we can't use it from DT, 2) it do nothing.
Added new Test-Component can be used from DT, and it can indicate called
function name. We can use it to trace callback order, understanding
ALSA SoC behavior, etc, etc...
Sample DT settings of Audio Graph Card2 is using Test-Component as CPU/Codec DAI.
You can easily try to use/test it if you added below line to your DT file.
Your .config needs to have below CONFIGs to use/test it.
It will probe sample Sound Card which has Normal/DPCM/Multi/Codec2Codec
connections.
#include "../../../../../sound/soc/generic/audio-graph-card2-custom-sample.dtsi"
CONFIG_SND_AUDIO_GRAPH_CARD2
CONFIG_SND_AUDIO_GRAPH_CARD2_CUSTOM_SAMPLE
CONFIG_SND_TEST_COMPONENT
Because Audio Graph Card2 is still under experimental stage, it will
indicate such warning when probing, and the DT might be updated/exchanged.
It can use Codec2Codec, but it will start automatically when probed,
and can't stop it so far. It should be updated.
Link: https://lore.kernel.org/r/87k0xszlep.wl-kuninori.morimoto.gx@renesas.com
Link: https://lore.kernel.org/r/871r8u4s6q.wl-kuninori.morimoto.gx@renesas.com
Link: https://lore.kernel.org/r/87a6mhwyqn.wl-kuninori.morimoto.gx@renesas.com
Link: https://lore.kernel.org/r/87tuitusy4.wl-kuninori.morimoto.gx@renesas.com
Link: https://lore.kernel.org/r/87a6jn56x0.wl-kuninori.morimoto.gx@renesas.com
v1 -> v2
- don't use "port" base for_each loop
v2 -> v3
- Rename audio-graph-card2 to rich-graph-card
- Rename DSP to DPCM not to confuse
- Normal/DPCM/Codec2Codec can use Single/Multi DAIs.
- use dpcm/multi/codec2codec node instead of using extra compatible
- Sample DTSI patch is separated to Single/Multi.
v3 -> v4
- Rename rich-graph-card to audio-graph-card2
- fixup custom sample driver's connection bug
- test-component compatible uses "verbose" instead of "vv"
v4 -> v5
- tidyup git-log comment at
- tidyup Custom Sample comment
Kuninori Morimoto (16):
ASoC: test-component: add Test Component YAML bindings
ASoC: test-component: add Test Component for Sound debug/test
ASoC: simple-card-utils: add asoc_graph_is_ports0()
ASoC: simple-card-utils: add codec2codec support
ASoC: add Audio Graph Card2 driver
ASoC: audio-graph-card2: add Multi CPU/Codec support
ASoC: audio-graph-card2: add DPCM support
ASoC: audio-graph-card2: add Codec2Codec support
ASoC: add Audio Graph Card2 Yaml Document
ASoC: add Audio Graph Card2 Custom Sample
ASoC: audio-graph-card2-custom-sample.dtsi: add Sample DT for Normal (Single)
ASoC: audio-graph-card2-custom-sample.dtsi: add Sample DT for Normal (Nulti)
ASoC: audio-graph-card2-custom-sample.dtsi: add DPCM sample (Single)
ASoC: audio-graph-card2-custom-sample.dtsi: add DPCM sample (Multi)
ASoC: audio-graph-card2-custom-sample.dtsi: add Codec2Codec sample (Single)
ASoC: audio-graph-card2-custom-sample.dtsi: add Codec2Codec sample (Multi)
.../bindings/sound/audio-graph-card2.yaml | 57 +
.../bindings/sound/test-component.yaml | 33 +
include/sound/graph_card.h | 21 +
include/sound/simple_card_utils.h | 4 +
sound/soc/generic/Kconfig | 20 +
sound/soc/generic/Makefile | 6 +
.../generic/audio-graph-card2-custom-sample.c | 183 +++
.../audio-graph-card2-custom-sample.dtsi | 227 +++
sound/soc/generic/audio-graph-card2.c | 1281 +++++++++++++++++
sound/soc/generic/simple-card-utils.c | 46 +-
sound/soc/generic/test-component.c | 659 +++++++++
11 files changed, 2536 insertions(+), 1 deletion(-)
create mode 100644 Documentation/devicetree/bindings/sound/audio-graph-card2.yaml
create mode 100644 Documentation/devicetree/bindings/sound/test-component.yaml
create mode 100644 sound/soc/generic/audio-graph-card2-custom-sample.c
create mode 100644 sound/soc/generic/audio-graph-card2-custom-sample.dtsi
create mode 100644 sound/soc/generic/audio-graph-card2.c
create mode 100644 sound/soc/generic/test-component.c
--
2.25.1
The headset type detection must run to set the analogue switches
correctly for the attached headset type. Without this only headsets
with wiring matching the chip default will have a functioning mic.
commit c26a5289e8 ("ASoC: cs42l42: Add support for set_jack calls")
moved the interrupt unmasking to the component set_jack() callback.
But it's not mandatory for a machine driver to register a struct
snd_soc_jack handler. Without a registered handler the type detection
would not have run and so the mic would not work on some types of
headset.
This patch restores the unmasking of TS_PLUG and TS_UNPLUG interrupts
during probe.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211015133619.4698-17-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver must free the IRQ in remove() to prevent the potential race
where an IRQ starts to be handled while the driver is being removed but
devres has not yet called free_irq(). However, the driver can run without
an interrupt but devm_free_irq() will hit a WARN() if no devres-managed
interrupt was ever created.
Fix this by only attempting to create the interrupt handler if the hardware
config specified an interrupt, and failing probe() if the interrupt could
not be created. This means that in cs42l42_remove() an interrupt must have
been registered if the irq number is valid and therefore it is safe to call
devm_free_irq().
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211015133619.4698-16-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the datasheet the SRC MCLK must be as near as possible to
(125 * sample rate). This means it should be ~6MHz for rates up to 48k
and ~12MHz for rates above that. As per datasheet table 4-21.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211015133619.4698-14-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
After enabling the HP or ADC by writing the corresponding PDN=0,
it takes around 20 milliseconds for it to power up and the midrail
supply to be stable. Add this wait into a DAPM widget callback.
If HP and ADC are both powering up in a DAPM sequence, there's no
need to do the wait twice. The widget will perform one wait in the
POST_PMU if there was a PRE_PMU for one or both.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211015133619.4698-13-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It isn't possible to switch MCLK between 12MHz and 24MHz rate groups
on-the-fly - this can only be done when cs42l42 is powered-down.
All "normal" SCLK rates use an MCLK in the 12MHz group, so change the
configs for SCLK > 12.288 MHz to use the PLL to generate an MCLK in
the 12MHz group.
As this means MCLK_DIV is always 0 it can be removed from the pll
configuration setup.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211015133619.4698-12-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver currently only supports configuring for sample rates <= 96k
and it isn't possible to setup a configuration that will support all
sample rates up to 192k.
For sample rates up to 96k MCLK is in the 12MHz group.
However, although 192k only requires an I2S clock in the 12MHz group,
the cs42l42 audio path is not natively 192k so the audio must be
resampled. But for 192k the SRC requires a 24MHz MCLK.
It is not possible to switch MCLK between 12MHz and 24MHz groups
on-the-fly. The 12MHz group supports all sample rates up to 96k.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211015133619.4698-11-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver can run without an interrupt so if devm_request_threaded_irq()
failed, the probe() just carried on. But if this was EPROBE_DEFER the
driver would continue without an interrupt instead of deferring to wait
for the interrupt to become available.
Fixes: 2c394ca796 ("ASoC: Add support for CS42L42 codec")
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211015133619.4698-6-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
An I2S frame always has two slots (left and right) even when sending
mono. The right channel (channel 2) of ASP TX will always have the
same bit width as the left channel and will always be on the high
phase of LRCLK.
The previous implementation always passed the field masks for both
channels to snd_soc_component_update_bits() but for mono the written value
only contained the settings for channel 1. The result was that for mono
channel 2 was set to 8-bit (which is an invalid configuration) with both
channels on the low phase of LRCLK.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 585e7079de ("ASoC: cs42l42: Add Capture Support")
Link: https://lore.kernel.org/r/20211015133619.4698-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When capture and playback substreams are both running at the same time,
cs42l42_pcm_hw_params() would be called for each direction. The first
call will configure the PLL. The second call must not write the PLL
configuration registers again if the first substream is already running,
as this could destabilize the PLL.
The DAI is marked symmetric sample bits and sample rate, so the two
directions will always have the same SCLK (I2S always has 2 channel slots
so the DAI does not need to require symmetric channels to guarantee the
same SCLK). However, since cs42l42_pll_config() is checking for an active
stream it may as well test that the requested SCLK is the same as the
currently active configuration.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211015133619.4698-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently errors on register read/write/update are reported with
an error code and the corresponding function but does not provide
any details on the which register number did it actually fail.
register number can give better clue and it should be easy to
locate the code and fix.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20211014161330.26645-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds Codec2Codec-Multi sample to audio-graph-card2-custom-sample.dtsi.
Because it can use very basic connection only for now,
it can use only
- 2channels
- S32_LE format
Test-Component driver has "IN" and "OUT" widget. Thus the route is
+--+ +-+
| | | |- Codec8 <- IN
| | <- | |- Codec9 <- IN
| | +-+
| |
| | +-+
| | -> | |- Codec10 -> OUT
| | | |- Codec11 -> OUT
+--+ +-+
One note here is that it will start works when it boot.
In other words we can't stop it so far.
We need to update driver for it in the future.
...
asoc-audio-graph-card2-custom-sample: multicodec <-> multicpu mapping ok
test-component test_codec: test_dai_startup() : test_codec.9
test-component test_codec: test_dai_startup() : test_codec.8
test-component test_codec: test_dai_startup() : test_codec.11
test-component test_codec: test_dai_startup() : test_codec.10
...
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87mtnelu2k.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds Codec2Codec-Single sample to audio-graph-card2-custom-sample.dtsi.
Because it can use very basic connection only for now,
it can use only
- 2channels
- S32_LE format
Test-Component driver has "IN" and "OUT" widget. Thus the route is
+--+
| | <-- Codec6 <-- IN
| | --> Codec7 --> OUT
+--+
One note here is that it will start works when it boot.
In other words we can't stop it so far.
We need to update driver for it in the future.
...
asoc-audio-graph-card2-custom-sample: test_codec.7 <-> test_codec.6 mapping ok
test-component test_codec: test_dai_startup() : test_codec.6
test-component test_codec: test_dai_startup() : test_codec.7
...
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87o87ulu2o.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds DPCM link Multi-CPU/Codec sample to
audio-graph-card2-custom-sample.dtsi.
This sample is assuming MIXer connection.
One note is that Multi-FE is not supported on ASoC
FE BE
**** +-+
CPU5 -- * * -- | | -- Codec4
CPU6 -- * * | | -- Codec5
**** +-+
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87pmsalu2s.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds DPCM link Single-CPU/Codec sample to
audio-graph-card2-custom-sample.dtsi.
This sample is assuming MIXer connection.
FE BE
****
CPU3 -- * * -- Codec3
CPU4 -- * *
****
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87r1cqlu2w.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Audio Graph Card2 settings is a little bit difficult for beginner,
and Customizing it also difficult/confusable too.
So, this patch adds sample for it.
You can easily use it by adding below line on your DT file,
and select CONFIGs to your .config.
#include "../../../../../sound/soc/generic/audio-graph-card2-custom-sample.dtsi"
CONFIG_SND_AUDIO_GRAPH_CARD2
CONFIG_SND_AUDIO_GRAPH_CARD2_CUSTOM_SAMPLE
CONFIG_SND_TEST_COMPONENT
This patch uses audio-graph-card2 base custom sample driver.
You can directly use audio-graph-card2 instead of custom sample driver
by modifing compatible.
- compatible = "audio-graph-card2-custom-sample";
+ compatible = "audio-graph-card2";
Sample custom driver will indicate customized print.
It is using Test-Component driver for CPU/Codec.
It can indicate more detail print of each behavior if user want to.
In such case, you need to update compatible to "xxx-nv" or "xxx-vv".
- compatible = "test-cpu";
+ compatible = "test-cpu-verbose";
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87tuhmlu35.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
audio-graph-card2 has customizing support.
This means user can re-use audio-graph-card2 DT parsing, and possible
to expand to own special handling.
This patch adds Audio Graph Card2 Customize Sample Driver.
It can re-use audio-graph-card2 parsing by calling
audio_graph2_parse_of(...), and user can expand each functions by
using hooks.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87v922lu3c.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds Codec2Codec support to audio-graph-card2.
It can use Codec2Codec but very simple case only for now.
It doesn't have "SWITCH" control yet, thus it start automatically
when it was probed, and can't stop, so far.
Thus it needs to be updated around widgets/routing handling,
and you need to understand that it is under experimental.
Codec has SND_SOC_DAPM_INPUT() (= IN) / SND_SOC_DAPM_OUTPUT(= OUT)
widgets in below case.
It is assuming 2channel, S32_LE format for now.
It needs to be updated, too.
It needs "codec2codec" node (= B), needs to have routing (= A),
need to indicate CPU side at links (= X).
ports@0 is for CPU side (= X), port@1 is Codec side (= Y).
It needs to have "rate" (= C)
+--+
| |<-- Codec0 <-- IN
| |--> Codec1 --> OUT
+--+
sound {
compatible = "audio-graph-card2";
(A) routing = "OUT" ,"DAI1 Playback",
"DAI0 Capture", "IN";
(X) links = <&c2c>;
(B) codec2codec {
ports {
(C) rate = <48000>;
(X) c2c: port@0 { c2cf_ep: endpoint { remote-endpoint = <&codec0_ep>; }; };
(Y) port@1 { c2cb_ep: endpoint { remote-endpoint = <&codec1_ep>; }; };
};
};
Codec {
ports {
port@0 {
bitclock-master;
frame-master;
codec0_ep: endpoint { remote-endpoint = <&c2cf_ep>; }; };
port@1 { codec1_ep: endpoint { remote-endpoint = <&c2cb_ep>; }; };
};
};
Link: https://lore.kernel.org/r/87k0xszlep.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87y26ylu4a.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
audio-graph-card2 will support DPCM/Multi/Codec2Codec,
and these will use almost same DT settings which uses
ports0 and ports1.
This patch adds asoc_graph_is_ports0() which checks
port is under port0 or not.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/875yu2n8ra.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We already have dummy-codec, dummy-platform.
But its issues are
1) we don't have dummy-cpu,
2) we can't select it via DeviceTree
3) It do nothing
Sometimes we want to have Dummy Sound Component for debugging,
for testing, for learning Framework behavior, etc, etc...
This patch adds Test-Component driver for it.
User can select CPU Component by using "test-cpu" compatible,
and can select Codec Component by using "test-codec" compatible.
It doesn't support Platform so far, but is easy to add.
We can verbose print to know its progress if user selected
xxx-verbose compatible driver.
for example,
test-cpu : silent Component, silent DAI
test-cpu-verbose-component : verbose Component, silent DAI
test-cpu-verbose-dai : silent Component, verbose DAI
test-cpu-verbose : verbose Component, verbose DAI
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/877dein8rx.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A little pop can be heard obviously from HP while playing a silent.
This patch fixes it by using two functions:
1. Enable HP 1bit output mode.
2. Change the charge pump switch size during playback on and off.
Signed-off-by: Derek Fang <derek.fang@realtek.com>
Link: https://lore.kernel.org/r/20211014094054.811-1-derek.fang@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There are several things the patch adding the support for 'I2S Reference'
got wrong:
- "None" selection is in fact equals to last selected reference
- The custom put overrides RX/TX len, TDM slot sizes, etc
- the enum is useless in most part for the reference tracking
- there is no need for EXT control as there is a single bit in
RT1011_TDM1_SET_1 register (bit 7) which selects the reference
- it was using ucontrol->value.integer.value[0] in the put/get callbacks
which causesed access to 'I2S Reference' enum with alsamixer to fail
Complements: c3de683c4d ("ASoC: rt1011: Fix 'I2S Reference' enum control caused error")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20211013123300.11095-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a noise issue for 8kHz sample rate on slave mode.
Compared with master mode, the difference is the DACDIV
setting, after correcting the DACDIV, the noise is gone.
There is no noise issue for 48kHz sample rate, because
the default value of DACDIV is correct for 48kHz.
So wm8960_configure_clocking() should be functional for
ADC and DAC function even if it is slave mode.
In order to be compatible for old use case, just add
condition for checking that sysclk is zero with
slave mode.
Fixes: 0e50b51aa2 ("ASoC: wm8960: Let wm8960 driver configure its bit clock and frame clock")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/1634102224-3922-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ChiYuan Huang <cy_huang@richtek.com>:
From: ChiYuan Huang <cy_huang@richtek.com>
This patch series Add the Richtek RT9120 support.
In v4:
- Add 'classd_tlv' for 'SPK Gain Volume' control item.
- Unify the tlv declaration to the postfix '_tlv'.
- Fix 'digital_tlv' mute as 1 to declare the minimum is muted.
In v3:
- Add dvdd regulator binding to check the dvdd voltage domain.
- Refine sdo_select_text.
- Use switch case in 'internal_power_event' function.
- Remove the volume and mute initially write in component probe.
- Remove the mute API. It's no need by HW design.
In v2:
- Add missing #sound-dai-cells property.
ChiYuan Huang (2):
ASoC: dt-bindings: rt9120: Add initial bindings
ASoC: rt9120: Add rt9210 audio amplifier support
.../devicetree/bindings/sound/richtek,rt9120.yaml | 59 +++
sound/soc/codecs/Kconfig | 10 +
sound/soc/codecs/Makefile | 2 +
sound/soc/codecs/rt9120.c | 495 +++++++++++++++++++++
4 files changed, 566 insertions(+)
create mode 100644 Documentation/devicetree/bindings/sound/richtek,rt9120.yaml
create mode 100644 sound/soc/codecs/rt9120.c
--
2.7.4
The only usage of acp5x_i2s_dai_ops is to assign its address to the ops
field in the snd_soc_dai_driver struct, which is a pointer to const.
Make it const to allow the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20211012211506.21159-1-rikard.falkeborn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
These are only assigned to the ops field in the snd_soc_dai_link struct
which is a pointer to const struct snd_soc_ops. Make them const to allow
the compiler to put them in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20211012205521.14098-1-rikard.falkeborn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This drops the rt9210 support due to a race with a new version being
sent out for some incremental changes.
Signed-off-by: Mark Brown <broonie@kernel.org>
The device advertises 8 formats, but only a rate of 48kHz is honored
by the hardware and 24 bits give chopped audio, so only report the
one working combination. This fixes out-of-the-box audio experience
with PipeWire which otherwise attempts to choose S24_3LE (while
PulseAudio defaulted to S16_LE).
Signed-off-by: Jonas Hahnfeld <hahnjo@hahnjo.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211012200906.3492-1-hahnjo@hahnjo.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The snd_hdac_bus_reset_link() contains logic to clear STATESTS register
before performing controller reset. This code dates back to an old
bugfix in commit e8a7f136f5 ("[ALSA] hda-intel - Improve HD-audio
codec probing robustness"). Originally the code was added to
azx_reset().
The code was moved around in commit a41d122449 ("ALSA: hda - Embed bus
into controller object") and ended up to snd_hdac_bus_reset_link() and
called primarily via snd_hdac_bus_init_chip().
The logic to clear STATESTS is correct when snd_hdac_bus_init_chip() is
called when controller is not in reset. In this case, STATESTS can be
cleared. This can be useful e.g. when forcing a controller reset to retry
codec probe. A normal non-power-on reset will not clear the bits.
However, this old logic is problematic when controller is already in
reset. The HDA specification states that controller must be taken out of
reset before writing to registers other than GCTL.CRST (1.0a spec,
3.3.7). The write to STATESTS in snd_hdac_bus_reset_link() will be lost
if the controller is already in reset per the HDA specification mentioned.
This has been harmless on older hardware. On newer generation of Intel
PCIe based HDA controllers, if configured to report issues, this write
will emit an unsupported request error. If ACPI Platform Error Interface
(APEI) is enabled in kernel, this will end up to kernel log.
Fix the code in snd_hdac_bus_reset_link() to only clear the STATESTS if
the function is called when controller is not in reset. Otherwise
clearing the bits is not possible and should be skipped.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211012142935.3731820-1-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We need to define the codec pin 0x1b to be the mic, but somehow
the mic doesn't support hot plugging detection, and Windows also has
this issue, so we set it to phantom headset-mic.
Also the determine_headset_type() often returns the omtp type by a
mistake when we plug a ctia headset, this makes the mic can't record
sound at all. Because most of the headset are ctia type nowadays and
some machines have the fixed ctia type audio jack, it is possible this
machine has the fixed ctia jack too. Here we set this mic jack to
fixed ctia type, this could avoid the mic type detection mistake and
make the ctia headset work stable.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214537
Reported-and-tested-by: msd <msd.mmq@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20211012114748.5238-1-hui.wang@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Access to 'I2S Reference' enum causes alsamixer to fail to load:
$ alsamixer
cannot load mixer controls: Invalid argument
cml_rt1011_rt5682 cml_rt1011_rt5682: control 2:0:0:TL I2S Reference:0: access overflow
The reason is that the original patch adding the code was using
ucontrol->value.integer.value[0]
instead the correct
ucontrol->value.enumerated.item[0]
for an ENUM control.
Fixes: 87f40af26c ("ASoC: rt1011: add i2s reference control for rt1011")
Reported-by: Seppo Ingalsuo <seppo.ingalsuo@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20211011144518.2518-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Ensure the default 0dB playback path is always used.
The code that set FULL_SCALE_VOL based on LOAD_DET_RCSTAT was
spurious, and resulted in a -6dB attenuation being accidentally
inserted into the playback path.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211011144903.28915-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The small set of cleanups against bytcr_rt5651 board file.
In v2:
- added commit message to patch 2 (Joe, Pierre)
- added cover letter (Pierre)
- added Hans to Cc list (Hans)
Andy Shevchenko (4):
ASoC: Intel: bytcr_rt5651: Get platform data via dev_get_platdata()
ASoC: Intel: bytcr_rt5651: Use temporary variable for struct device
ASoC: Intel: bytcr_rt5651: use devm_clk_get_optional() for mclk
ASoC: Intel: bytcr_rt5651: Utilize dev_err_probe() to avoid log
saturation
sound/soc/intel/boards/bytcr_rt5651.c | 118 +++++++++++---------------
1 file changed, 50 insertions(+), 68 deletions(-)
--
2.33.0
Michael Forney reported an incorrect padding type that was defined in
the commit 80fe7430c7 ("ALSA: add new 32-bit layout for
snd_pcm_mmap_status/control") for PCM control mmap data.
His analysis is correct, and this caused the misplacements of PCM
control data on 32bit arch and 32bit compat mode.
The bug is that the __pad2 definition in __snd_pcm_mmap_control64
struct was wrongly with __pad_before_uframe, which should have been
__pad_after_uframe instead. This struct is used in SYNC_PTR ioctl and
control mmap. Basically this bug leads to two problems:
- The offset of avail_min field becomes wrong, it's placed right after
appl_ptr without padding on little-endian
- When appl_ptr and avail_min are read as 64bit values in kernel side,
the values become either zero or corrupted (mixed up)
One good news is that, because both user-space and kernel
misunderstand the wrong offset, at least, 32bit application running on
32bit kernel works as is. Also, 64bit applications are unaffected
because the padding size is zero. The remaining problem is the 32bit
compat mode; as mentioned in the above, avail_min is placed right
after appl_ptr on little-endian archs, 64bit kernel reads bogus values
for appl_ptr updates, which may lead to streaming bugs like jumping,
XRUN or whatever unexpected.
(However, we haven't heard any serious bug reports due to this over
years, so practically seen, it's fairly safe to assume that the impact
by this bug is limited.)
Ideally speaking, we should correct the wrong mmap status control
definition. But this would cause again incompatibility with the
existing binaries, and fixing it (e.g. by renumbering ioctls) would be
really messy.
So, as of this patch, we only correct the behavior of 32bit compat
mode and keep the rest as is. Namely, the SYNC_PTR ioctl is now
handled differently in compat mode to read/write the 32bit values at
the right offsets. The control mmap of 32bit apps on 64bit kernels
has been already disabled (which is likely rather an overlook, but
this worked fine at this time :), so covering SYNC_PTR ioctl should
suffice as a fallback.
Fixes: 80fe7430c7 ("ALSA: add new 32-bit layout for snd_pcm_mmap_status/control")
Reported-by: Michael Forney <mforney@mforney.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Cc: <stable@vger.kernel.org>
Cc: Rich Felker <dalias@libc.org>
Link: https://lore.kernel.org/r/29QBMJU8DE71E.2YZSH8IHT5HMH@mforney.org
Link: https://lore.kernel.org/r/20211010075546.23220-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
dev_err_probe() avoids printing into log when the deferred probe is invoked.
This is possible when clock provider is pending to appear.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211007170250.27997-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The devm_clk_get_optional() helper returns NULL when devm_clk_get()
returns -ENOENT. This makes things slightly cleaner. The added benefit
is mostly cosmetic.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211007170250.27997-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dev_err_probe() avoids printing into log when the deferred probe is invoked.
This is possible when clock provider is pending to appear.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211007165715.27463-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The devm_clk_get_optional() helper returns NULL when devm_clk_get()
returns -ENOENT. This makes things slightly cleaner. The added benefit
is mostly cosmetic.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211007165715.27463-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use temporary variable for struct device to make code neater.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211007165715.27463-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Access to platform data via dev_get_platdata() getter to make code cleaner.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211007165715.27463-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We are using fch clock controller as parent mclk source for rt5682
codec. Add config to enable clock framework support for 48MHz fixed
clock when machine driver config is selected.
Signed-off-by: Ajit Kumar Pandey <AjitKumar.Pandey@amd.com>
Link: https://lore.kernel.org/r/20211011055354.67719-1-AjitKumar.Pandey@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
'component' is allocated in snd_soc_register_component(), but component->list
is not initalized, this may cause snd_soc_del_component_unlocked() deref null
ptr in the error handing case.
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
RIP: 0010:__list_del_entry_valid+0x81/0xf0
Call Trace:
snd_soc_del_component_unlocked+0x69/0x1b0 [snd_soc_core]
snd_soc_add_component.cold+0x54/0x6c [snd_soc_core]
snd_soc_register_component+0x70/0x90 [snd_soc_core]
devm_snd_soc_register_component+0x5e/0xd0 [snd_soc_core]
tas2552_probe+0x265/0x320 [snd_soc_tas2552]
? tas2552_component_probe+0x1e0/0x1e0 [snd_soc_tas2552]
i2c_device_probe+0xa31/0xbe0
Fix by adding INIT_LIST_HEAD() to snd_soc_component_initialize().
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20211009065840.3196239-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In the case where the call to i2s_tdm_prepare_enable_mclk fails the
function returns before the error handling goto is executed. Fix this
by removing the return do perform the intended error handling exit.
Fixes: 081068fd64 ("ASoC: rockchip: add support for i2s-tdm controller")
Addresses-Coverity: ("Structurally dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Message-Id: <20211008095430.62680-2-colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The call to rockchip_i2s_ch_to_io is only useful for its return
value which is not being used. The function call also has no
side effects, the call is effectively useless and can be removed.
Addresses-Coverity: ("Useless call")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Message-Id: <20211008095430.62680-1-colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Because clock names are modified in mediatek CCF driver, sync the updated
clock names to audsys driver.
Signed-off-by: Trevor Wu <trevor.wu@mediatek.com>
Message-Id: <20211008070424.14347-1-trevor.wu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The small set of cleanups against bytcht_es8316 board file.
In v4:
- fixed Pierre's email (Pierre)
- added Hans to the Cc list
In v3:
- actually added a Pierre's tag (Mark)
In v2:
- added tag (Pierre)
- added commit message to the patch 2 (Joe)
Andy Shevchenko (4):
ASoC: Intel: bytcht_es8316: Get platform data via dev_get_platdata()
ASoC: Intel: bytcht_es8316: Use temporary variable for struct device
ASoC: Intel: bytcht_es8316: Switch to use gpiod_get_optional()
ASoC: Intel: bytcht_es8316: Utilize dev_err_probe() to avoid log
saturation
sound/soc/intel/boards/bytcht_es8316.c | 37 +++++++++-----------------
1 file changed, 12 insertions(+), 25 deletions(-)
--
2.33.0
The fixed maximum size of IPC message does not allow for large
transfers, e.g. for filter data. Currently such messages will
be divided into smaller pieces and sent to firmware in multiple
chunks. For future IPC, this strategy is not suitable.
The maximum IPC message size is limited by host box size which
can be known when firmware is ready, so the fw_ready callback
can allocate IPC messages with platform-specific sizes instead
of the current fixed-size.
To be compatible with released firmware, current platforms will
still use SOF_IPC_MSG_MAX_SIZE. For future platforms, there will
be a new fw_ready function and the platform-specific allocation
will take place there.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Message-Id: <20211008093836.28210-1-peter.ujfalusi@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
dev_err_probe() avoids printing into log when the deferred probe is invoked.
This is possible when clock provider is pending to appear.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Message-Id: <20211007164523.27094-5-andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
First of all, replace indexed API by plain one since we have index 0.
Second, switch to optional variant and drop duplicated code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Message-Id: <20211007164523.27094-4-andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use temporary variable for struct device to make code neater.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Message-Id: <20211007164523.27094-3-andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Access to platform data via dev_get_platdata() getter to make code cleaner.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Message-Id: <20211007164523.27094-2-andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The max98927 codec on some devices (i.e. Xiaomi Mi A2 Lite phone) requires
hardware-resetting the codec by driving a reset-gpio. This series adds
support for it through an optional reset-gpios property.
v4:
* Correctly assert/deassert the GPIO states
* Wait for the i2c port to be ready after reset
* Reset device when removed
v3:
* Fix indentation on the dev_err_probe line
v2:
* Use dev_err_probe instead of dev_err
Alejandro Tafalla (2):
ASoC: max98927: Handle reset gpio when probing i2c
dt-bindings: sound: max98927: Add reset-gpios optional property
.../devicetree/bindings/sound/max9892x.txt | 3 +++
sound/soc/codecs/max98927.c | 25 +++++++++++++++++++
sound/soc/codecs/max98927.h | 1 +
3 files changed, 29 insertions(+)
--
2.33.0
Hi,
The aim of this series is to clean up, make it easier to interpret and less
'chatty' prints aimed for debugging errors.
For example currently the DSP/IPC dump is printed every time we have an IPC
timeout and it is posible to lost the first and more indicative dump to find the
rootcause.
Regards,
Peter
---
Peter Ujfalusi (18):
ASoC: SOF: debug: Swap the dsp_dump and ipc_dump sequence for
fw_exception
ASoC: SOF: ipc and dsp dump: Add markers for better visibility
ASoC: SOF: Print the dbg_dump and ipc_dump once to reduce kernel log
noise
ASoC: SOF: loader: Print the DSP dump if boot fails
ASoC: SOF: intel: atom: No need to do a DSP dump in atom_run()
ASoC: SOF: debug/ops: Move the IPC and DSP dump functions out from the
header
ASoC: SOF: debug: Add SOF_DBG_DUMP_OPTIONAL flag for DSP dumping
ASoC: SOF: intel: hda-loader: Use snd_sof_dsp_dbg_dump() for DSP dump
ASoC: SOF: Drop SOF_DBG_DUMP_FORCE_ERR_LEVEL and sof_dev_dbg_or_err
ASoC: SOF: debug: Print out the fw_state along with the DSP dump
ASoC: SOF: ipc: Re-enable dumps after successful IPC tx
ASoC: SOF: ops: Force DSP panic dumps to be printed
ASoC: SOF: Introduce macro to set the firmware state
ASoC: SOF: intel: hda: Drop 'error' prefix from error dump functions
ASoC: SOF: core: Clean up snd_sof_get_status() prints
ASoC: SOF: loader: Drop SOF_DBG_DUMP_REGS flag when firmware start
fails
ASoC: SOF: Intel: hda-loader: Drop SOF_DBG_DUMP_REGS flag from
dbg_dump calls
ASoC: SOF: Intel: hda: Dump registers and stack when SOF_DBG_DUMP_REGS
is set
Pierre-Louis Bossart (1):
ASoC: SOF: core: debug: force all processing on primary core
sound/soc/sof/core.c | 24 ++++++-------
sound/soc/sof/debug.c | 61 ++++++++++++++++++++++++++++++--
sound/soc/sof/intel/atom.c | 5 +--
sound/soc/sof/intel/hda-loader.c | 11 +++---
sound/soc/sof/intel/hda.c | 16 +++------
sound/soc/sof/ipc.c | 10 ++++--
sound/soc/sof/loader.c | 11 ++++--
sound/soc/sof/ops.c | 3 ++
sound/soc/sof/ops.h | 12 +------
sound/soc/sof/pm.c | 6 ++--
sound/soc/sof/sof-priv.h | 31 ++++++++++------
sound/soc/sof/topology.c | 6 ++++
12 files changed, 131 insertions(+), 65 deletions(-)
--
2.33.0
Hello,
this is version 5 of the I2S/TDM driver patchset. A big thanks
to everyone who has provided their valuable feedback so far.
Changes in v5:
driver:
- change comment style of the first comment to C++ style
- make refcount non-atomic, as it's only ever used inside
a spinlock
- use newer SND_SOC_DAIFMT_CB* defines
- change ternary statements to if/else conditions
- make _clk_compensation_put return 1 if clock changed
- implement set_bclk_ratio callback
- always set half frame sync mode in TDM mode
- automatically enable mclk-calibrate mode when the clocks for
it are specified in the device tree
bindings:
- add Reviewed-by: Rob Herring
- drop rockchip,frame-width property (done by set_bclk_ratio)
- drop rockchip,fsync-half-frame property
- drop rockchip,mclk-calibrate property
dts:
- drop empty codec block from Quartz64 device tree
Changes in v4:
driver:
- factor TDE/RDE enable/disable into their own inlined functions
- add an RDE disable in a location where it looks like it was
forgotten (rxctrl else), judging by corresponding TDE code
- remove parentheses around CLK_PPM_MIN/MAX values
- wording + titlecasing in the clock compensation control
- use if statement in precious_reg instead
- refactor rockchip_i2s_io_multiplex to have the switch statements
in a function call to make the function less unwieldy
- get rid of IS_ERR checks around clk enable/disable calls where
already checked before by the probe
- reworded some error message strings
- fix potential deadlock in txrxctrl found by Sugar Zhang
using spin_lock_irqsave
- fix potential deadlock in trcm_mode found by Sugar Zhang
using spin_lock_irqsave
- use devm_platform_get_and_ioremap_resource in probe
- only set DMA things if controller has capture/playback ability.
Did not move this into init_dai because I'd then need to pass in
the res and probe it earlier in the function, and it's also used
elsewhere in the probe function
- use _get_optional_exclusive for reset controls, as some controllers
only have capture or playback capability
bindings:
- remove status = "okay" since that's the default
- change the path configs to be an enum
- rename "foo" to "bus"
- make resets optional as controller may lack either playback or
capture capability, and therefore also doesn't have a reset.
At least one reset is still required, because a controller with
no playback and no capture is not very useful
Changes in v3:
driver:
- alphabetically sort includes
- check pm_runtime_get_sync return value, act on it
- remove unnecessary initialisers in set_fmt
- use udelay(15) in retry code: 10 retries * 15 = 150, so at worst
we wait the full i2s register access delay
- fix some weird returns to return directly
- use __maybe_unused instead of #ifdef CONFIG_PM_SLEEP, also put
__maybe_unused on the runtime callbacks
- use (foo) instead of foo in header macros for precedence reasons
- when using mclk-calibrate, also turn off/on those clocks during
suspend and resume operations
- remove mclk_tx and mclk_rx reenablement code in remove
- move hclk enablement further down the probe, and disable it
on probe failure
- make reset controls mandatory, since the bindings state this too
- use _exclusive for getting the reset controls
- change reset assert/deassert delays to both be 10 usec
(thank you Sugar Zhang!)
- properly prepare and enable all mclks in probe, especially before
calling clk_get_rate on them
- if registering PCM fails, also use the cleanup error path instead of
returning directly
- bring back playback and capture only but in the way Sugar Zhang
suggested it: set those modes depending on dma-names
- rework clock enablement in general. Probe now always enables these,
instead of relying on the pm resume thing
- add myself to MAINTAINERS for this driver
dt bindings:
- fix a description still mentioning clk-trcm in the schema
- document rockchip,io-multiplex, a property that describes the
hardware as having multiplexed I2S GPIOs so direction needs to
be changed dynamically
- document rockchip,mclk-calibrate, which allows specifying
different clocks for the two sample rate bases and switch between
them as needed
- dma-names now doesn't have a set order and items can be absent to
indicate that the controller doesn't support this mode
- add myself to MAINTAINERS for these bindings
Changes in v2:
- remove ad-hoc writeq and needless (and broken) optimisation in
reset assert/deassert. This wouldn't have worked on Big Endian,
and would've been pointless on any other platform, as the
overhead for saving one write was comparatively big
- fix various checkpatch issues
- get rid of leftover clk-trcm in schema
- set status = "okay" in example in schema instead of "disabled"
- change dma-names so rx is first, adjust device trees as necessary
- properly reference uint32-array for rx-route and tx-route
instead of uint32
- replace trcm-sync with two boolean properties, adjust DT changes
accordingly and also get rid of the header file
- get rid of rockchip,no-dmaengine. This was only needed for
some downstream driver and shouldn't be in the DT
- get rid of rockchip,capture-only/playback-only. Rationale being
that I have no way to test whether they're needed, and
unconditionally setting channels_min to 0 breaks everything
- change hclk description in "clocks"
Nicolas Frattaroli (4):
ASoC: rockchip: add support for i2s-tdm controller
ASoC: dt-bindings: rockchip: add i2s-tdm bindings
arm64: dts: rockchip: add i2s1 on rk356x
arm64: dts: rockchip: add analog audio on Quartz64
.../bindings/sound/rockchip,i2s-tdm.yaml | 198 ++
MAINTAINERS | 7 +
.../boot/dts/rockchip/rk3566-quartz64-a.dts | 31 +-
arch/arm64/boot/dts/rockchip/rk356x.dtsi | 26 +
sound/soc/rockchip/Kconfig | 11 +
sound/soc/rockchip/Makefile | 2 +
sound/soc/rockchip/rockchip_i2s_tdm.c | 1848 +++++++++++++++++
sound/soc/rockchip/rockchip_i2s_tdm.h | 398 ++++
8 files changed, 2520 insertions(+), 1 deletion(-)
create mode 100644 Documentation/devicetree/bindings/sound/rockchip,i2s-tdm.yaml
create mode 100644 sound/soc/rockchip/rockchip_i2s_tdm.c
create mode 100644 sound/soc/rockchip/rockchip_i2s_tdm.h
--
2.33.0
Recent changes in soc-pcm completely broke basic support for mixers on
Intel systems: the filters on BE states prevent the connection of a
second mixer input while the back-end is already active.
Rather than reverting the changes, which would be problematic for
Tegra systems, this patch suggests an additional filter which will
only apply to Tegra systems. This is a temporary solution which will
have to be revisited - additional issues have been reported with DPCM.
Fixes: 0c25db3f76 ('ASoC: soc-pcm: Don't reconnect an already active BE')
Suggested-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20211004212141.193136-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When the system plays a sound immediately after resuming from S3,
it could hear a little pop from headphones.
It is due to the HP was unmuted before the completion of
jack re-detection finished in parallel.
This patch adds a lock to make sure the HP unmute after jack detect handler,
and adds a few depop changes.
Signed-off-by: Derek Fang <derek.fang@realtek.com>
Link: https://lore.kernel.org/r/20211007085519.12543-1-derek.fang@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This commit adds support for the rockchip i2s-tdm controller,
which enables audio output on the following rockchip SoCs:
- px30
- rk1808
- rk3308
- rk3566
- rk3568
- rv1126
This is a cleaned up version of the downstream vendor kernel's
driver. It can be enabled through the SND_SOC_ROCKCHIP_I2S_TDM
configuration option.
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Link: https://lore.kernel.org/r/20211001171531.178775-2-frattaroli.nicolas@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch prepares the introduction of the compress API with SOF.
After each fragment is accepted by the DSP we need to inform
the userspace applications that they can send the next fragment.
This is done via snd_compr_fragment_elapsed.
Similar with the PCM case, in order to avoid sending an IPC before
the previous IPC is handled we need to schedule a delayed work to
call snd_compr_fragment_elapsed().
See snd_sof_pcm_period_elapsed.
To sum up this patch offers the following API to SOF code:
* snd_sof_compr_init_elapsed_work
* snd_sof_compr_fragment_elapsed
Note that implementation for compressed function is in a new file
selected via CONFIG_SND_SOC_SOF_COMPRESS invisible config option.
This option is automatically selected for platforms that support
the compress interface. For now only i.MX8 platforms support this.
For symmetry we introduce snd_sof_pcm_init_elapsed_work to setup
the work struct for PCM case.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Bud Liviu-Alexandru <budliviu@gmail.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Paul Olaru <paul.olaru@oss.nxp.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20211004152147.1268978-5-daniel.baluta@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This makes IMX use the newly introduced generic IPC ops
instead of imx specific ones, and removes the old IMX
ipc ops, as they are no longer needed.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Bud Liviu-Alexandru <budliviu@gmail.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20211004152147.1268978-4-daniel.baluta@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This operations should be generic as there is nothing Intel
specific. This works well for NXP i.MX8 stream IPC ops.
We start by moving sof/intel/intel-ipc.c into sof/stream-ipc.c and
rename the functions to be generic.
Notice that we use newly introduced snd_sof_dsp_mailbox_read
instead of sof_mailbox_read, to make sure that we are not
bound to existing MMIO memory access, and we allow platform
to implement their own memory access routines.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Bud Liviu-Alexandru <budliviu@gmail.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@gmail.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20211004152147.1268978-3-daniel.baluta@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We need to introduce snd_sof_mailbox_{read/write} in order to provide
a generic way for mailbox access. These routines are optional, each
platform can implement their own specific routines.
So far, all platforms use mmapped I/O thus they can use custom made
routines sof_mailbox_read / sof_mailbox_write that use MMIO.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Bud Liviu-Alexandru <budliviu@gmail.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20211004152147.1268978-2-daniel.baluta@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
First thing the pipelines function which have "struct device *dev" as
parameter do is:
struct snd_sof_dev *sdev = dev_get_drvdata(dev);
and in all cases the passed dev is actually coming from sdev->dev.
Skip this steps and pass directly the sdev to all pipelines related
functions as few of them already does this.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211006111651.10027-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When removing the topology components, do not power down
the primary core. Doing so will result in an IPC timeout
when the SOF PCI device runtime suspends.
Fixes: 0dcdf84289 ("ASoC: SOF: add a "core" parameter to widget loading functions")
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20211006104041.27183-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of checking the fw_state to decide what information should be
printed, use the SOF_DBG_DUMP_REGS bit in the flags to dump registers and
stack.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211006110645.26679-20-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In cl_dsp_init() we are powering up the DSP, register dump is not valid.
In hda_dsp_cl_boot_firmware() we are downloading the firmware to DSP, again
the register dump is not a valid concept.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211006110645.26679-19-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_sof_dsp_run() failure indicates that the DSP did not even booted up,
thus asking for dumping registers at this point is not valid.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211006110645.26679-18-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Clean up the error prints when decoding the status in snd_sof_get_status():
Drop the "error:" prefixes from the prints,
Use %# to print hexadecimal numbers,
Reword some of the messages to be more precise,
For a known error print out the panic code as well,
For unknown error print only the panic code without the magic
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211006110645.26679-17-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Drop the 'error' prefix printed in hda_dsp_dump_ext_rom_status(),
hda_ipc_irq_dump() and hda_ipc_dump() as it gives no value to the
information we print.
The DSP and IPC dump is marked now, which makes the 'error' prefix more
redundant.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211006110645.26679-16-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add sof_set_fw_state() macro to wrap the sdev->fw_state management to allow
actions to be taken when certain state is set or when state is changing.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211006110645.26679-15-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If a DSP panic happens we want to see the dumps.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211006110645.26679-14-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The dumps are silenced after an IPC tx timeout by default.
The IPC timeout can indicate severe error (firmware crash) or in some cases
it is less devastating and the firmware remains operational, the timeout
was due to a scheduling spike or other anomaly.
In any case consequent IPC timeouts will not print dumps but if any IPC do
succeed than we should re-enable the dumps to print dumps the next time
a timeout might happen.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211006110645.26679-13-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The fw state can be an important information along with the DSP dump.
Print it out before the dump.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211006110645.26679-12-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The sof_dev_dbg_or_err() is only used by intel/hda.c when dumping dsp
debug information.
It was used to print the extended rom status in either dev_dbg (during
retries) and finally with dev_err, but other lines were printed with
dev_err regardless.
Since we now only print the dump once, the flag and the macros is no longer
needed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20211006110645.26679-11-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
