Add OMAP3 SmartReflex IRQs in hwmod structures. Without these IRQs
being registered the SmartReflex driver will be unable to get the
IRQ numbers to handle notifications.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The VPBOUNDINTST field of the ERRCONFIG register has an additional
functional meaning of force clearing the SR internal signal with VP
(sr_interruptz).
This can result in scenarios where the VP->SR protocol is violated
because the SR internal signal with VP is already high and VP will
never clear the vpirqclr signal.
Therefore during the next force update to reset to nominal voltage,
VP cannot pulse vpirqclr, so the PRCM HW cannot generate the tranxdone
IRQ and the situation is not recoverable until a cold reset is invoked.
To prevent this situation, check if status is set before clearing it
as this needs to be done only on a need basis.
Reported-by: Vincent Bour <v-bour@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
ERRCONFIG register has status bits that were intended not to
be destroyed by bad modification. We cleanup and simplify the
handling the status in the modify path.
Reported-by: Vincent Bour <v-bour@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
SmartReflex fix for erratum ID i724.
Since OMAP's VP and PRM modules do not get reset by warm reset,
we should ensure that proper shutdown procedure is followed prior
to allowing the kernel to reboot back up.
Without this, Smartreflex module might be left active or
system might be caught in an indeterminate sequence when
software controlled reboot is triggered, leaving the next
reboot behavior to be unpredictable.
In the case of hardware controlled warm reset such as that
by watchdog timer, prevention of this scenario is not possible.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
SmartReflex AVS Errorgen module supplies signals to Voltage
Processor. It is suggested that by disabling Errorgen module
before we disable VP, we might be able to ensure lesser
chances of race condition to occur in the system.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
sr_modify_mask takes mask, value as parameters, the usage
currently is value, mask which is wrong, as a result
vpboundint_st which was supposed to have been disabled,
does not get disabled.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
To set sr ntarget values for all volt_domain,
volt_table is retrieved by doing a look_up of 'vdd_name'
field from omap_hwmod but voltage domain pointer does not
belong to omap_hwmod and is not used anywhere else.
As a part of voltage layer and SR Layer clean up volt
pointer is removed from omap_hwmod and added in dev
attributes of SR. The value of the field must match
the voltage domain names for the binding to be effective.
Tested on OMAP3630 SDP, OMAP3530 Beagleboard and
OMAP4430 SDP Board.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Shweta Gulati <shweta.gulati@ti.com>
Acked by: Nishanth Menon <nm@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The PandaBoard features a Texas Instruments WiLink7 Bluetooth
chip, supported by the "btwilink" driver.
Signed-off-by: Mircea Gherzan <mgherzan@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add platform data for drivers that recently appeared in kernel:
backlight and TWL4030 poweroff support.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
sdp4430_spi_board_info.irq was initialized to ETH_KS8851_IRQ and in
omap_4430sdp_init() overwritten with gpio_to_irq(ETH_KS8851_IRQ) before
sdp4430_spi_board_info was registered. This is a bit confusing, so
better don't initialize .irq and document that it is set later.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for the EMAC Ethernet controller in the AM35xx SoC.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM35xx SoCs include DaVinci EMAC IP. Initialization code in
board-am3517evm.c is pretty board independent and will work for any
AM35xx based board so move this code to it's own file to be reused by
other boards.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This change converts TSC2005 related GPIO requests to be done with
gpio_request_array() method and explicitly inits mux configuration for
these GPIOs.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds omap_reserve functionality to board-omap3logic.c
Signed-off-by: Alex Gershgorin <alexg@meprolight.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
of bugfixes and driver updates there's quite a few framework enhancements.
Most are either small or are laying the groundwork for user visible
features (especially dynamic PCM), the most directly visible change is
the dmaengine library. There's also a bunch of regmap API enhancements
pulled into the tree so that either the framework or drivers can take
advantage of the new features.
Changes include:
- Support for widgets not associated with a CODEC, an important part of
the dynamic PCM framework.
- A library factoring out the common code shared by dmaengine based DMA
drivers contributed by Lars-Peter Clausen. This will save a lot of
code and make it much easier to deploy enhancements to dmaengine.
- Support for binary controls, used for providing runtime configuration
of algorithm coefficients.
- A new DAPM widget type for regulator supplies allowing drivers for
devices that can power down unused supplies while active to do without
any per-driver code.
- DAPM widgets for DAIs, initially giving a speed boost for playback
startup and shutdown and also the basis for CODEC<->CODEC DAI link
support.
- Support for specifying the number of significant bits on audio
interfaces, useful for allowing applications to know how much effort to
put into generating data for a larger sample format.
- Conversion of the FSI driver used on some SH processors to DMAEngine.
- New CODEC drivers for Maxim MAX9768 and Wolfson Microelectronics WM2200.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=FpJH
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into topic/asoc
This has been a very active release for ASoC, as well as the usual raft
of bugfixes and driver updates there's quite a few framework enhancements.
Most are either small or are laying the groundwork for user visible
features (especially dynamic PCM), the most directly visible change is
the dmaengine library. There's also a bunch of regmap API enhancements
pulled into the tree so that either the framework or drivers can take
advantage of the new features.
Changes include:
- Support for widgets not associated with a CODEC, an important part of
the dynamic PCM framework.
- A library factoring out the common code shared by dmaengine based DMA
drivers contributed by Lars-Peter Clausen. This will save a lot of
code and make it much easier to deploy enhancements to dmaengine.
- Support for binary controls, used for providing runtime configuration
of algorithm coefficients.
- A new DAPM widget type for regulator supplies allowing drivers for
devices that can power down unused supplies while active to do without
any per-driver code.
- DAPM widgets for DAIs, initially giving a speed boost for playback
startup and shutdown and also the basis for CODEC<->CODEC DAI link
support.
- Support for specifying the number of significant bits on audio
interfaces, useful for allowing applications to know how much effort to
put into generating data for a larger sample format.
- Conversion of the FSI driver used on some SH processors to DMAEngine.
- New CODEC drivers for Maxim MAX9768 and Wolfson Microelectronics WM2200.
These two branches are a dependency for the at91 device tree changes,
so we pull them in here. at91/base2+cleanup will get merged through
the arm-soc cleanup2 branch, while the irqdomain tree will be sent
by Grant before this one gets integrated.
Conflicts:
drivers/rtc/rtc-at91sam9.c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Conflicts:
arch/arm/mach-omap1/gpio16xx.c
drivers/gpio/gpio-omap.c
Merge in the runtime-pm-cleanup branch from the gpio tree into
next/cleanup, this resolves a nonobvious merge conflict between
the two branches. Both branches move parts of the gpio-omap
driver into platform code, this takes the superset of both
changes.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add missing break statement in the function omap3xxx_check_revision.
The commit id 4390f5b2cb [ARM: OMAP: TI814X: Add cpu type macros
and detection support], removed the 'break' statement from the function
omap3xxx_check_revision(), resulting into wrong omap/cpu_revision
initialization for AM335x devices.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
[tony@atomide.com: refreshed to apply after changes to cpu_rev]
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix L4_EMU_34XX_BASE error after iomap changes
ARM: OMAP2+: Limit omap_read/write usage to legacy USB drivers
ARM: OMAP: Remove plat/io.h by splitting it into mach/io.h and mach/hardware.h
ARM: OMAP2+: Move most of plat/io.h into local iomap.h
ARM: OMAP1: Move most of plat/io.h into local iomap.h
ARM: OMAP1: Move 16xx GPIO system clock to platform init code
ARM: OMAP: Move omap_init_consistent_dma_size() to local common.h
ARM: OMAP2+: Move SDRC related functions from io.h into local common.h
ARM: OMAP2+: Drop DISPC L3 firewall code
ARM: OMAP2xxx: PM: remove obsolete timer disable code in the suspend path
ARM: OMAP: McSPI: Remove unused flag from struct omap2_mcspi_device_config
(update to latest rmk/for-arm-soc branch)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
arm/dts: Add support for TI OMAP3 EVM board
arm/dts: OMAP4: Update DTS file with new GIC bindings
arm/dts: OMAP3: Add i2c controller nodes
arm/dts: OMAP4: Add i2c controller nodes
ARM: OMAP2+: Set Kconfig dependencies for PROC_DEVICETREE
arm/dts: OMAP3&4: Remove the '0x' prefix for serial nodes
ARM: OMAP1: kconfig: Enable IRQ_DOMAIN by default for OMAP1 platforms
ARM: OMAP2+: pm: Do not init statically the SR and voltage layer with DT
ARM: OMAP2+: omap_device: Replace dev_warn by dev_dbg in omap_device_build_from_dt
ARM: OMAP2+: board-generic: Remove un-needed .atag_offset for DT_MACHINE
ARM: OMAP2+: kconfig: Enable devicetree by default for OMAP2+ systems
arm/dts: OMAP: Remove bootargs node from board files
* 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: split omap2/3/4_check_revision function
ARM: OMAP2+: Make cpu_rev static global variable
bits are all for devices that still need to get set up in board code.
Only three platforms are in this set of fixes: omap2+, pxa and lpc32xx.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ElaK
-----END PGP SIGNATURE-----
Merge tag 'fixes-3.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Arnd Bergmann says:
"Another set of arm-soc bug fixes on top of v3.3-rc5. The few larger
bits are all for devices that still need to get set up in board code.
Only three platforms are in this set of fixes: omap2+, pxa and lpc32xx."
* tag 'fixes-3.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (22 commits)
ARM: LPC32xx: serial.c: Fixed loop limit
ARM: LPC32xx: serial.c: HW bug workaround
ARM: LPC32xx: irq.c: Clear latched event
ARM: LPC32xx: Fix interrupt controller init
ARM: LPC32xx: Fix irq on GPI_28
ARM: OMAP2: fix mailbox init code
ARM: OMAP2+: gpmc-smsc911x: add required smsc911x regulators
ARM: OMAP1: Fix out-of-bounds array access for Innovator
OMAP3 EVM: remove out-of-bounds array access of gpio_leds
ARM: OMAP: Fix build error when mmc_omap is built as module
ARM: OMAP: Fix kernel panic with HSMMC when twl4030_gpio is a module
pxa/hx4700: add platform device and I2C info for AK4641 codec
arch/arm/mach-pxa/: included linux/gpio.h twice
arch/arm/mach-mmp/: some files include some headers twice
ARM: pxa: fix error handling in pxa2xx_drv_pcmcia_probe
ARM: pxa: fix including linux/gpio.h twice
ARM: pxa: fix mixed declarations and code in sharpsl_pm
ARM: pxa: fix wrong parsing gpio event on spitz
ARM: OMAP2+: usb-host: fix compile warning
ARM: OMAP4: Move the barrier memboclk_steal() as part of reserve callback
...
* 'at91-3.4-base2+cleanup' of git://github.com/at91linux/linux-at91: (20 commits)
ARM: at91: properly sort dtb files in Makefile.boot
ARM: at91: add at91sam9g25ek.dts in Makefile.boot
ARM: at91/board-dt: drop default console
Atmel: move console default platform_device to serial driver
ARM: at91: merge SRAM Memory banks thanks to mirroring
ARM: at91: finally drop at91_sys_read/write
ARM: at91/rtc-at91sam9: pass the GPBR to use via resources
ARM: at91:rtc/rtc-at91sam9: ioremap register bank
ARM: at91/rtc-at91sam9: each SoC can select the RTT device to use
ARM: at91/PMC: make register base soc independent
ARM: at91/PMC: move assignment out of printf
ARM: at91/pm_slowclock: add runtime detection of memory contoller
ARM: at91: make sdram/ddr register base soc independent
ARM: at91: move at91rm9200 sdramc defines to at91rm9200_sdramc.h
ARM: at91/pm_slowclock: function slow_clock() accepts parameters
ARM: at91/pm_slowclock: rename register to named define
ARM: at91/ST: remove not needed casts
ARM: at91: make ST (System Timer) soc independent
ARM: at91: make matrix register base soc independent
ARM: at91/at91x40: remove use of at91_sys_read/write
Based on top of the at91/9x5, rmk/for-armsoc, at91/device-board,
at91/pm_cleanup and at91/base.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
With the introduction of iomap changes platform init code
fails for emu.c if CONFIG_OMAP3_EMU is selected:
arch/arm/mach-omap2/emu.c:35:8: error:
'L4_EMU_34XX_BASE' undeclared here (not in a function)
Signed-off-by: Tony Lindgren <tony@atomide.com>
VUSB is a fixed regulator, so get rid of the apply_uV constraint
for it, which fixes the following error seen at boot on omap4
SDP and PANDA boards.
machine_constraints_voltage: VUSB: failed to apply 3300000uV constraint
twl_reg twl_reg.46: can't register VUSB, -22
twl_reg: probe of twl_reg.46 failed with error -22
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
CCDN is the last common channel register in all OMAP4 versions. Use
cpu_is_omap44xx() instead of the cpu_is_omap4430().
cpu_is_omap4430() returns 0 unconditionally. This causes that the
dma_common_ch_end register variable is not configured correctly on OMAP4, not
even for OMAP4430.
Because of this, registers between CCFN - CCDN will be not cleard in the
omap2_clear_dma function in OMAP4.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
WARNING: vmlinux.o(.text+0x226d0):
Section mismatch in reference from the function
platform_cpu_die() to the function .cpuinit.text:omap4_hotplug_cpu()
The function platform_cpu_die() references
the function __cpuinit omap4_hotplug_cpu().
This is often because platform_cpu_die lacks a __cpuinit
annotation or the annotation of omap4_hotplug_cpu is wrong.
Thanks to Russell King for suggesting to use __ref instead of
the initial (and wrong) approach to use __cpuinit.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
WARNING: arch/arm/mach-omap2/built-in.o(.text+0x8b80):
Section mismatch in reference from the function omap4_hotplug_cpu() to
the function .cpuinit.text:omap_secondary_startup()
The function omap4_hotplug_cpu() references
the function __cpuinit omap_secondary_startup().
This is often because omap4_hotplug_cpu lacks a __cpuinit
annotation or the annotation of omap_secondary_startup is wrong.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
All the fixes are for the OMAP IOMMU driver. The first patch is the
biggest one. It fixes the calls of the function omap_find_iovm_area() in
the omap-iommu-debug module which expects a 'struct device' parameter
since commit fabdbca instead of an omap_iommu handle. The
omap-iommu-debug code still passed the handle to the function which
caused a crash.
The second patch fixes a NULL pointer dereference in the OMAP code and
the third patch makes sure that the omap-iommu is initialized before the
omap-isp driver, which relies on the iommu. The last patch is only a
workaround until defered probing is implemented.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=aclV
-----END PGP SIGNATURE-----
Merge tag 'iommu-fixes-v3.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
IOMMU fixes for Linux 3.3-rc5
All the fixes are for the OMAP IOMMU driver. The first patch is the
biggest one. It fixes the calls of the function omap_find_iovm_area() in
the omap-iommu-debug module which expects a 'struct device' parameter
since commit fabdbca instead of an omap_iommu handle. The
omap-iommu-debug code still passed the handle to the function which
caused a crash.
The second patch fixes a NULL pointer dereference in the OMAP code and
the third patch makes sure that the omap-iommu is initialized before the
omap-isp driver, which relies on the iommu. The last patch is only a
workaround until defered probing is implemented.
* tag 'iommu-fixes-v3.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
ARM: OMAP: make iommu subsys_initcall to fix builtin omap3isp
iommu/omap: fix NULL pointer dereference
iommu/omap: fix erroneous omap-iommu-debug API calls
* 'imx/driver' of git://git.linaro.org/people/shawnguo/linux-2.6: (3 commits)
ARM: imx6q: add cko1 clock
ARM: mxc: make imx_dma_is_general_purpose more generic for sdma
ARM: imx6: Rename DEBUG_IMX6Q_UART to UART4
* kirkwood/board: (2 commits)
ARM: kirkwood: convert uart0 to devicetree.
ARM: kirkwood: add dreamplug (fdt) support.
Series sent by email from Jason Cooper <jason@lakedaemon.net>
Update to Linux 3.3-rc3
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
omap3isp depends on omap's iommu and will fail to probe if
initialized before it (which always happen if they are builtin).
Make omap's iommu subsys_initcall as an interim solution until
the probe deferral mechanism is merged.
Reported-by: James <angweiyang@gmail.com>
Debugged-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Cc: stable <stable@vger.kernel.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Hiroshi Doyu <hdoyu@nvidia.com>
Cc: Joerg Roedel <Joerg.Roedel@amd.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Use the of_irq_init API introduced in 3.2 to handle
interrupt-controller with DT.
Update the irq_match table to map the proper XXX_of_init
functions for INTC and GIC drivers.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Add a function to initialize the OMAP2/3 interrupt controller (INTC)
using a device tree node.
This version take advantage of the new irq_domain_add_legacy API.
Replace some printk() with the proper pr_ macro.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Building omap_devices should only be done at init time, and since
omap_device_build() is using early_platform calls which are also
__init, this ensures that omap_device isn't trying to use functions
that disappear.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that omap hsmmc init is split into two functions, it's safe
to mark omap_hsmmc_init and omap_mux related functions to __init.
This basically reverts the following fixes for the case where
TWL was compiled as a module:
a98f77b (ARM: omap: fix section mismatch warning for sdp3430_twl_gpio_setup())
8930b4e (ARM: omap: fix section mismatch warnings in mux.c caused by hsmmc.c)
Additionally it fixes up the remaining section warnings for
all callers of omap_mux functions.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Drivers should no longer use omap_read/write functions
but instead use ioremap + read/write functions.
As some USB legacy code is still shared between omap1 and
omap2420, let's limit the omap_read/write to plat/usb.h.
Note that the long term fix is to update the drivers to
use ioremap and read/write functions. That can now be
done as a separate patch series that is limited to the
USB drivers.
Also make sure the legacy omap1-keypad.c driver builds
if selected for 2420 based systems.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is needed to minimize io.h so the SoC specific io.h
for ARMs can removed.
Note that minimal driver changes for DSS and RNG are needed to
include cpu.h for SoC detection macros.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There's no need to have these defines in plat/io.h.
Note that we now need to ifdef omap_read/write calls
as they will be available for omap1 only.
While at it, clean up the includes to group them like
they typically are grouped.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove omap_{read,write}l() from the 24xx PM code. The clocksource
code should now handle what this was supposed to do.
Tested on N800 -- but it's hard to say whether this fixes anything.
OMAP24xx static suspend path is currently broken, and this patch
doesn't change that.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rob Herring <robherring2@gmail.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Flag single_channel in struct omap2_mcspi_device_config is not used
by drivers/spi/spi-omap2-mcspi.c so we may remove it from include/plat/mcspi.h
and affected board files.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise we get:
`omap_sr_remove' referenced in section `.data' of arch/arm/mach-omap2/built-in.o:
defined in discarded section `.devexit.text' of arch/arm/mach-omap2/built-in.o
Signed-off-by: Tony Lindgren <tony@atomide.com>
If we don't have ARCH_OMAP2, 3 or 4 selected randconfig will always
fail with multiple errors as the CPU and MACHINE are not set.
Fix this by changing arch/arm/Makefile to build mach-omap2 based on
ARCH_OMAP2PLUS. And let's introduce SOC_OMAP and SOC_OMAP_NOOP that
allow randconfig to generate buildable .config files.
Note that we can also remove few uncecssary ARCH_OMAP2PLUS lines
as they are all within if ARCH_OMAP2PLUS block.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'vexpress-dt-v3.3-rc4' of git://git.linaro.org/people/pawelmoll/linux: (573 commits)
ARM: vexpress: Add Device Tree for V2P-CA15 core tile (TC1 variant)
ARM: vexpress: Add Device Tree for V2P-CA9 core tile
ARM: vexpress: Add Device Tree for V2P-CA5s core tile
ARM: vexpress: Motherboard RS1 memory map support
ARM: vexpress: Add Device Tree support
ARM: vexpress: Use FDT data in platform SMP calls
ARM: versatile: Map local timers using Device Tree when possible
ARM: vexpress: Get rid of MMIO_P2V
This adds full device tree boot support for the versatile express
platform, as has been awaited for a long time.
Conflicts:
arch/arm/mach-vexpress/core.h
The definition of AMBA_DEVICE was removed in one branch, and the
definition of MMIO_P2V was removed in the other branch.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Otherwise we get:
arch/arm/mach-omap2/board-zoom-display.c:64: undefined reference to `twl_i2c_read_u8'
arch/arm/mach-omap2/board-zoom-display.c:65: undefined reference to `twl_i2c_read_u8'
arch/arm/mach-omap2/board-zoom-display.c:84: undefined reference to `twl_i2c_write_u8'
arch/arm/mach-omap2/board-zoom-display.c:86: undefined reference to `twl_i2c_write_u8'
arch/arm/mach-omap2/board-zoom-display.c:91: undefined reference to `twl_i2c_write_u8'
arch/arm/mach-omap2/board-zoom-display.c:92: undefined reference to `twl_i2c_write_u8'
arch/arm/mach-omap2/board-zoom-display.c:72: undefined reference to `twl_i2c_write_u8'
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise we can get:
arch/arm/mach-omap2/mux.h:249:31: error: board_mux causes a section type conflict
Signed-off-by: Tony Lindgren <tony@atomide.com>
If CONFIG_SOC_OMAP3430 is not set and CONFIG_HDQ_MASTER_OMAP
is selected for w1 driver we get the following error:
arch/arm/mach-omap2/devices.c:662:13: error:
'OMAP_HDQ_BASE' undeclared here (not in a function)
Looks like OMAP_HDQ_BASE is valid for all omaps except
2420, so we can remove the ifdef and not register
the device on 2420.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise we get:
warning: (ARCH_OMAP3 && ARCH_OMAP4) selects USB_ARCH_HAS_EHCI
which has unmet direct dependencies (USB_SUPPORT)
Signed-off-by: Tony Lindgren <tony@atomide.com>
During kernel init, we reset all IP blocks on the OMAP that we can,
even if there is no driver compiled for that IP block. Unlike most IP
blocks, the I2C block requires some extra programming for this to
work. This reset code is incorrectly omitted when the I2C driver is
deselected. In this circumstance, the build breaks. Fix by compiling
the I2C reset code unconditionally.
Problem reported by Russell King <linux@arm.linux.org.uk>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Russell King <linux@arm.linux.org.uk>
Tested-by: Shubhrajyoti <shubhrajyoti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix this:
arch/arm/mach-omap2/mailbox.c: In function 'omap2_mbox_probe':
arch/arm/mach-omap2/mailbox.c:354: error: 'omap2_mboxes' undeclared (first use in this function)
arch/arm/mach-omap2/mailbox.c:354: error: (Each undeclared identifier is reported only once
arch/arm/mach-omap2/mailbox.c:354: error: for each function it appears in.)
Which happens on CONFIG_ARCH_OMAP2 && !CONFIG_SOC_OMAP2420, due to
missing omap2_mboxes declaration.
In addition, make sure we declare the right mailbox instances for 2430.
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Hiroshi Doyu <hdoyu@nvidia.com>
Cc: Omar Ramirez Luna <omar.ramirez@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This fixes smsc911x support on platforms using gpmc_smsc911x_init().
Commit c7e963f688 (net/smsc911x: Add regulator support) added
the requirement that platforms provide vdd33a and vddvario supplies.
Signed-off-by: Matt Porter <mporter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* lpc32xx/drivers: (566 commits)
ARM: LPC32xx: ADC support for mach-lpc32xx
Includes an update to Linux 3.3-rc4
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A few more things this time around. The only thing warranting some
commentry is the modpost change, which allows folk building a Thumb2
enabled kernel to see section mismatch warnings. This is why many
weren't noticed with OMAP.
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM/audit: include audit header and fix audit arch
ARM: OMAP: fix voltage domain build errors with PM_OPP disabled
ARM/PCI: Remove ARM's duplicate definition of 'pcibios_max_latency'
ARM: 7336/1: smp_twd: Don't register CPUFREQ notifiers if local timers are not initialised
ARM: 7327/1: need to include asm/system.h in asm/processor.h
ARM: 7326/2: PL330: fix null pointer dereference in pl330_chan_ctrl()
ARM: 7164/3: PL330: Fix the size of the dst_cache_ctrl field
ARM: 7325/1: fix v7 boot with lockdep enabled
ARM: 7324/1: modpost: Fix section warnings for ARM for many compilers
ARM: 7323/1: Do not allow ARM_LPAE on pre-ARMv7 architectures
Now that most platforms don't need disable_fiq and arch_ret_to_user
macros, we can remove the empty macros or empty entry-macro.S files.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Otherwise we can get the following warning on some compilers:
arch/arm/mach-omap2/board-omap3evm.c:384:11:
warning: array subscript is above array bounds
The omap3evm BSP enables a GPIO LED on the twl4030 chip. However,
the static gpio_leds array doesn't have an entry for it. This is
most likely a copy-and-paste error, because it has been in there
since the first commit of the omap3evm BSP (53c5ec31).
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
[tony@atomide.com: updated comments with the warning]
Signed-off-by: Tony Lindgren <tony@atomide.com>
commit 2fd149645e (ARM: OMAP2+: UART: Remove omap_uart_can_sleep and
add pm_qos) removed omap_uart_can_sleep and omap3_can_sleep, but not
their declarations. So remove those now.
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Shubhrajyoti D <shubhrajyoti@ti.com>
[khilman@ti.com: minor changelog edits]
Signed-off-by: Kevin Hilman <khilman@ti.com>
commit 2fd149645e (ARM: OMAP2+: UART: Remove
omap_uart_can_sleep and add pm_qos) removed the last usage of
'can_sleep' but did not remove the field.
commit 8612bd22f3 (ARM: OMAP2+: UART: Avoid console uart idling
during bootup) removed the last non-trivial use of 'pdev'.
So remove these fields and the one trivial use.
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: NeilBrown <neilb@suse.de>
[khilman@ti.com: minor changelog edits]
Signed-off-by: Kevin Hilman <khilman@ti.com>
The voltage domain code wants the voltage tables, which are in the
opp*.c files. These files aren't built when PM_OPP is disabled,
causing the following build errors at link time:
twl-common.c:(.init.text+0x2e48): undefined reference to `omap34xx_vddmpu_volt_data'
twl-common.c:(.init.text+0x2e4c): undefined reference to `omap34xx_vddcore_volt_data'
twl-common.c:(.init.text+0x2e5c): undefined reference to `omap36xx_vddmpu_volt_data'
twl-common.c:(.init.text+0x2e60): undefined reference to `omap36xx_vddcore_volt_data'
twl-common.c:(.init.text+0x2830): undefined reference to `omap44xx_vdd_mpu_volt_data'
twl-common.c:(.init.text+0x283c): undefined reference to `omap44xx_vdd_iva_volt_data'
twl-common.c:(.init.text+0x2844): undefined reference to `omap44xx_vdd_core_volt_data'
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Otherwise omap_device_build() and omap_mux related functions
can't be marked as __init when twl is build as a module.
If a board is using GPIO pins or regulators configured by an
external chip, such as TWL PMIC on I2C bus, the board must
mark those MMC controllers as deferred. Additionally both
omap_hsmmc_init() and omap_hsmmc_late_init() must be called
by the board.
For MMC controllers using internal GPIO pins for card
detect and regulators the slots don't need to be marked
deferred. In this case calling omap_hsmmc_init() is sufficient.
Only mark the MMC slots using gpio_cd or gpio_wd as deferred
as noted by Igor Grinberg <grinberg@compulab.co.il>.
Note that this patch does not change the behaviour for
board-4430sdp.c board-omap4panda.c. These boards wrongly
rely on the omap_hsmmc.c init function callback to configure
the PMIC GPIO interrupt lines on external chip. If the PMIC
interrupt lines are not configured during init, they will
fail.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise we get the following error:
arch/arm/mach-omap2/built-in.o: In function `n8x0_mmc_callback':
twl-common.c:(.text+0x108a0): undefined reference to
`omap_mmc_notify_cover_event'
Fix this by warning about unusable MMC cover events.
The long term fix needs to change the MMC drivers to
register board specific callbacks directly with PMIC.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On some omaps twl4030_gpio has a callback to try to initialize
the MMC controller. If twl4030_gpio is compiled as a module,
bad things can happen because the callback function starts
calling functions that are supposed to be marked __init:
Kernel panic - not syncing: Attempted to kill the idle task!
twl4030_gpio twl4030_gpio: can't dispatch IRQs from modules
gpiochip_add: registered GPIOs 192 to 209 on device: twl4030
Unable to handle kernel paging request at virtual address b82a4c74
...
Additionally if this does not fail, warnings are produced
about trying to register the MMC multiple times.
Fix this by removing __init from omap_mux_get_by_name,
and add checks if omap2_hsmmc_init() is getting called more
than once.
Note that this will get fixed properly later on by splitting
omap2_hsmmc_init into two functions.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The majority of them are regression fixes for stuff that broke during
the merge 3.3 window.
The notable ones are:
* The at91 ata drivers both broke because of an earlier cleanup patch that
some other patches were based on. Jean-Christophe decided to remove
the legacy at91_ide driver and fix the new-style at91-pata driver while
keeping the cleanup patch. I almost rejected the patches for being too
late and too big but in the end decided to accept them because they
fix a regression.
* A patch fixing build breakage from the sysdev-to-device conversion
colliding with other changes touches a number of mach-s3c files.
* b0654037 "ARM: orion: Fix Orion5x GPIO regression from MPP cleanup"
is a mechanical change that unfortunately touches a lot of lines
that should up in the diffstat.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=QYVn
-----END PGP SIGNATURE-----
Merge tag 'fixes-3.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
These are the bug fixes that have accumulated since 3.3-rc3 in arm-soc.
The majority of them are regression fixes for stuff that broke during
the merge 3.3 window.
The notable ones are:
* The at91 ata drivers both broke because of an earlier cleanup patch that
some other patches were based on. Jean-Christophe decided to remove
the legacy at91_ide driver and fix the new-style at91-pata driver while
keeping the cleanup patch. I almost rejected the patches for being too
late and too big but in the end decided to accept them because they
fix a regression.
* A patch fixing build breakage from the sysdev-to-device conversion
colliding with other changes touches a number of mach-s3c files.
* b0654037 "ARM: orion: Fix Orion5x GPIO regression from MPP cleanup"
is a mechanical change that unfortunately touches a lot of lines
that should up in the diffstat.
* tag 'fixes-3.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
ARM: at91: drop ide driver in favor of the pata one
pata/at91: use newly introduced SMC accessors
ARM: at91: add accessor to manage SMC
ARM: at91:rtc/rtc-at91sam9: ioremap register bank
ARM: at91: USB AT91 gadget registration for module
ep93xx: fix build of vision_ep93xx.c
ARM: OMAP2xxx: PM: fix OMAP2xxx-specific UART idle bug in v3.3
ARM: orion: Fix USB phy for orion5x.
ARM: orion: Fix Orion5x GPIO regression from MPP cleanup
ARM: EXYNOS: Add cpu-offset property in gic device tree node
ARM: EXYNOS: Bring exynos4-dt up to date
ARM: OMAP3: cm-t35: fix section mismatch warning
ARM: OMAP2: Fix the OMAP2 only build break seen with 2011+ ARM tool-chains
ARM: tegra: paz00: fix wrong UART port on mini-pcie plug
ARM: tegra: paz00: fix wrong SD1 power gpio
i2c: tegra: Add devexit_p() for remove
ARM: EXYNOS: Correct M-5MOLS sensor clock frequency on Universal C210 board
ARM: EXYNOS: Correct framebuffer window size on Nuri board
ARM: SAMSUNG: Fix missing api-change from subsys_interface change
ARM: EXYNOS: Fix "warning: initialization from incompatible pointer type"
...
In the case of DT, the PMIC and SR initialization will be done using
a completely different mechanism.
Disable this part if a DT blob is available.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
irq_domain_add_simple() was a stop-gap measure until complete irq_domain
support was complete. This patch removes the irq_domain_add_simple()
interface.
This patch also drops the explicit irq_domain initialization performed
by the mach-versatile code because the versatile interrupt controller
already has irq_domain support built into it. This was a bug that was
hanging around quietly for a while, but with the full irq_domain which
actually verifies that irq_domain ranges are available it would cause
the registration to fail and the system wouldn't boot.
v4: Fixed number of irqs in mx5 gpio code
v2: Updated to pass in host_data pointer on irq_domain allocation.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Cc: Russell King <linux@arm.linux.org.uk>
Tested-by: Olof Johansson <olof@lixom.net>
Some .atag_offset entries were wrongly added during a merge conflict
resolution in 3.3.
Remove them all, since DT boot does not use that attribute anymore.
Replace as well the #if... by #ifdef for consistency.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
when commit 3528c58 (OMAP: omap_device: when
building return platform_device instead of
omap_device) started returning a platform_device
instead of a omap_device pointer when building
a device, it failed to convert all users introducing
a compile warning when building
arch/arm/mach-omap2/usb-host.c.
This patch fixes that warning.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
arm_memblock_steal() is not suppose to be used outside ->reserve callback.
OMAP barrier errata code was using it outside reserve callback and hence
it was broken.
Move the allocation as part of ->reserve callback to fix the it.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP4 cpuidle driver is reporting the state requested by governor
rather than the actually attempted one.
This is obviously misleading sysfs and powertop cpuidle statistics.
Fix it so that stats are reported correctly.
Reported-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[khilman@ti.com: minor changelog edits]
Signed-off-by: Kevin Hilman <khilman@ti.com>
opp_find_freq_ceil and opp_get_voltage are documented as requiring
rcu_lock to be held. So hold it.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This set of changes are fixing various section mismatch warnings which
look to be completely valid. Primerily, those which are fixed are those
which can cause oopses by manipulation of driver binding via sysfs. For
example: calling code marked __init from driver probe __devinit
functions.
Some of these changes will be reworked at the next merge window when the
underlying reasons are sorted out. In the mean time, I think it's
important to have this fixed for correctness.
Also included in this set are fixes to various error messages in OMAP -
including making them gramatically correct, fixing a few spelling
errors, and more importantly, making them greppable by unwrapping them.
Tony Lindgren has acked all these patches, put them out for testing a
week ago, and I've tested them on the platforms I have.
* 'omap-fixes-warnings' of git://git.linaro.org/people/rmk/linux-arm:
ARM: omap: resolve nebulous 'Error setting wl12xx data'
ARM: omap: fix wrapped error messages in omap_hwmod.c
ARM: omap: fix section mismatch warnings in mux.c caused by hsmmc.c
ARM: omap: fix section mismatch warning for sdp3430_twl_gpio_setup()
ARM: omap: fix section mismatch error for omap_4430sdp_display_init()
ARM: omap: fix section mismatch warning for omap_secondary_startup()
ARM: omap: preemptively fix section mismatch in omap4_sdp4430_wifi_mux_init()
ARM: omap: fix section mismatch warning in mux.c
ARM: omap: fix section mismatch errors in TWL PMIC driver
ARM: omap: fix uninformative vc/i2c configuration error message
ARM: omap: fix vc.c PMIC error message
ARM: omap: fix prm44xx.c OMAP44XX_IRQ_PRCM build error
This pull request covers the major oopsing issues with OMAP, caused by
the lack of the TWL driver. Even when the TWL driver is not built in,
we shouldn't oops.
* 'omap-fixes-urgent' of git://git.linaro.org/people/rmk/linux-arm:
ARM: omap: fix broken twl-core dependencies and ifdefs
ARM: omap: fix oops in drivers/video/omap2/dss/dpi.c
ARM: omap: fix oops in arch/arm/mach-omap2/vp.c when pmic is not found
It's useful to print the error code when a called function fails so a
diagnosis of why it failed is possible. In this case, it fails because
we try to register some data for the wl12xx driver, but as the driver
is not configured, a stub function is used which simply returns -ENOSYS.
Let's do the simple thing for -rc and print the error code.
Also, the return code from platform_register_device() at each of these
sites was not being checked. Add some checking, and again print the
error code.
This should be fixed properly for the next merge window so we don't
issue error messages merely because a driver is not configured.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
While trying to debug my OMAP platforms, they emitted this message:
omap_hwmod: %s: enabled state can only be entered from initialized, idle, or disabled state
The following backtrace said it was from a function called '_enable',
which didn't provide much clue. Grepping didn't find it either.
The message is wrapped, so unwrap the message so grep can find it. Do
the same for three other messages in this file.
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The previous commit causes new section mismatch warnings:
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdb30): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_gpio()
The function omap_init_hsmmc() references
the function __init omap_mux_init_gpio().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_gpio is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdb4c): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_gpio()
The function omap_init_hsmmc() references
the function __init omap_mux_init_gpio().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_gpio is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdb60): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdb6c): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdb78): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdb90): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdb9c): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdba8): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdbc0): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdbcc): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdbd8): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdbf8): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc04): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc10): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc28): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc34): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc40): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc58): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc64): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc70): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc7c): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
Again, as for omap2_hsmmc_init(), these functions are callable at
runtime via the gpio-twl4030.c driver, and so these can't be marked
__init.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xd0f0): Section mismatch in reference from the function sdp3430_twl_gpio_setup() to the function .init.text:omap2_hsmmc_init()
The function sdp3430_twl_gpio_setup() references
the function __init omap2_hsmmc_init().
This is often because sdp3430_twl_gpio_setup lacks a __init
annotation or the annotation of omap2_hsmmc_init is wrong.
sdp3430_twl_gpio_setup() is called via platform data from the
gpio-twl4030 module, which can be inserted and removed at runtime.
This makes sdp3430_twl_gpio_setup() callable at runtime, and prevents
it being marked with an __init annotation.
As it calls omap2_hsmmc_init() unconditionally, the only resolution to
this warning is to remove the __init markings from omap2_hsmmc_init()
and its called functions. This addresses the functions in hsmmc.c.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xb798): Section mismatch in reference from the function omap_4430sdp_display_init() to the function .init.text:omap_display_init()
The function omap_4430sdp_display_init() references
the function __init omap_display_init().
This is often because omap_4430sdp_display_init lacks a __init
annotation or the annotation of omap_display_init is wrong.
Fix this by adding __init to omap_4430sdp_display_init().
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
WARNING: vmlinux.o(.text+0x1c664): Section mismatch in reference from the function omap_secondary_startup() to the function .cpuinit.text:secondary_startup()
The function omap_secondary_startup() references
the function __cpuinit secondary_startup().
This is often because omap_secondary_startup lacks a __cpuinit
annotation or the annotation of secondary_startup is wrong.
Unfortunately, fixing this causes a new warning which is harder to
solve:
WARNING: arch/arm/mach-omap2/built-in.o(.text+0x5328): Section mismatch in reference from the function omap4_hotplug_cpu() to the function .cpuinit.text:omap_secondary_startup()
The function omap4_hotplug_cpu() references
the function __cpuinit omap_secondary_startup().
This is often because omap4_hotplug_cpu lacks a __cpuinit
annotation or the annotation of omap_secondary_startup is wrong.
because omap4_hotplug_cpu() is used by power management code as well,
which may not end up using omap_secondary_startup().
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Found by review.
omap4_sdp4430_wifi_mux_init() is called by an __init marked function,
and only calls omap_mux_init_gpio() and omap_mux_init_signal() which
are both also an __init marked functions.
The only reason this doesn't issue a warning is because the compiler
inlines omap4_sdp4430_wifi_mux_init() into omap4_sdp4430_wifi_init().
So, lets add the __init annotation to ensure this remains safe should
the compiler choose not to inline.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
WARNING: arch/arm/mach-omap2/built-in.o(.text+0x15a4): Section mismatch in reference from the function omap_mux_init_signals() to the function .init.text:omap_mux_init_signal()
The function omap_mux_init_signals() references
the function __init omap_mux_init_signal().
This is often because omap_mux_init_signals lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On my OMAP4 platform, I'm getting this error message repeated several
times at boot:
omap_vc_i2c_init: I2C config for all channels must match.
omap_vc_i2c_init: I2C config for all channels must match.
This doesn't help identify what the problem is. Fix this message to
be more informative:
omap_vc_i2c_init: I2C config for vdd_iva does not match other channels (0).
omap_vc_i2c_init: I2C config for vdd_mpu does not match other channels (0).
This allows us to identify which voltage domains have a problem, and
what the I2C configuration state (a boolean, i2c_high_speed) setting
being used actually is.
From this we find that omap4_core_pmic has i2c_high_speed false, but
omap4_iva_pmic and omap4_mpu_pmic both have it set true.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
While testing on my OMAP3430 platform, this error message was emitted:
omap_vc_init_channel: PMIC info requried to configure vc forvdd_core not populated.Hence cannot initialize vc
Trying to find this message was difficult because it was wrapped across
several lines. It also mis-spells "required", doesn't read very well,
and has spaces lacking. Let's replace it with a more concise:
omap_vc_init_channel: No PMIC info for vdd_core
While we're here, fix a simple spelling error in a comment.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When CONFIG_OF is disabled, the compile fails with:
arch/arm/mach-omap2/prm44xx.c:41: error: 'OMAP44XX_IRQ_PRCM' undeclared here (not in a function)
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On OMAP2420-based systems, the PM code ignores the state of the UART
functional clocks when determining what idle state to enter. This
breaks the serial port now that the UART driver's clock behavior can
be controlled via the PM autosuspend timeout.
To fix, remove the special-case idle handling for the UARTs in the
OMAP2420/2430 PM idle code added by commit
4af4016c53 ("OMAP3: PM: UART: disable
clocks when idle and off-mode support").
Tested on Nokia N800. This patch is a collaboration between Tony
Lindgren <tony@atomide.com> and Paul Walmsley <paul@pwsan.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Just a few new device ids, omap serial driver regression fixes, and a
build fix for the 8250 driver movement.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk80KZgACgkQMUfUDdst+yk0HgCeIdU3VTWqdxZDXp3G1sFIXZ1b
47YAnRAMAar+/aLaNhqGrcz7aa5y2cUU
=8sr8
-----END PGP SIGNATURE-----
Merge tag 'tty-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Serial/TTY fixes for the 3.3-rc3 tree
Just a few new device ids, omap serial driver regression fixes, and a
build fix for the 8250 driver movement.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'tty-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: serial: omap-serial: wakeup latency constraint is in microseconds, not milliseconds
tty: serial: OMAP: block idle while the UART is transferring data in PIO mode
tty: serial: OMAP: use a 1-byte RX FIFO threshold in PIO mode
m32r: relocate drivers back out of 8250 dir
tty: fix a build failure on sparc
serial: samsung: Add support for EXYNOS5250
serial: samsung: Add support for EXYNOS4212 and EXYNOS4412
drivers/tty/vt/vt_ioctl.c: fix KDFONTOP 32bit compatibility layer
Prevent OMAP UARTs from going idle while they are still transferring
data in PIO mode. This works around an oversight in the OMAP UART
hardware present in OMAP34xx and earlier: an idle UART won't send a
wakeup when the TX FIFO threshold is reached. This causes long delays
during data transmission when the MPU powerdomain enters a low-power
mode. The MPU interrupt controller is not able to respond to
interrupts when it's in a low-power state, so the TX buffer is not
refilled until another wakeup event occurs.
This fix changes the erratum i291 DMA idle workaround. Rather than
toggling between force-idle and no-idle, it will toggle between
smart-idle and no-idle. The important part of the workaround is the
no-idle part, so this shouldn't result in any change in behavior.
This fix should work on all OMAP UARTs. Future patches intended for
the 3.4 merge window will make this workaround conditional on a
"feature" flag, and will use the OMAP36xx+ TX event wakeup support.
Thanks to Kevin Hilman <khilman@ti.com> for mentioning the erratum i291
workaround, which led to the development of this approach.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xeae8):
Section mismatch in reference from the function cm_t35_init_usbh()
to the (unknown reference) .init.data:(unknown)
The function cm_t35_init_usbh() references
the (unknown reference) __initdata (unknown).
This is often because cm_t35_init_usbh lacks a __initdata
annotation or the annotation of (unknown) is wrong.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the latest Sourcery G++ Lite 2011.03-41 and latest linaro
tool-chains OMAP2 only build breaks with below error.
arch/arm/mach-omap2/omap-smc.S: Assembler messages:
arch/arm/mach-omap2/omap-smc.S:30: Error: selected processor does not support ARM mode `smc #0'
arch/arm/mach-omap2/omap-smc.S:53: Error: selected processor does not support ARM mode `smc #0'
arch/arm/mach-omap2/omap-smc.S:61: Error: selected processor does not support ARM mode `smc #0'
arch/arm/mach-omap2/omap-smc.S:69: Error: selected processor does not support ARM mode `smc #0'
arch/arm/mach-omap2/omap-smc.S:77: Error: selected processor does not support ARM mode `smc #0'
make[1]: *** [arch/arm/mach-omap2/omap-smc.o] Error 1
OMAP2 devices doesn't have the security support but the security support
was getting built because of OMAP2PLUS. Don't build security code for
OMAP2 devices.
While at it, fix the secure-common line in the Makefile to use tabs
instead of spaces.
Reported-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
It includes:
- a compile fix for fsl-diu-fb
- a fix for a suspend/resume issue in atmel_lcdfb
- a fix for a suspend/resume issue in OMAP
- a workaround for a hardware bug to avoid physical damage in OMAP
- a really trivial dead code removal in intelfb
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.12 (GNU/Linux)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=2uP4
-----END PGP SIGNATURE-----
Merge tag 'fbdev-fixes-for-3.3-1' of git://github.com/schandinat/linux-2.6
fbdev fixes for 3.3
It includes:
- compile fix for fsl-diu-fb
- fix for a suspend/resume issue in atmel_lcdfb
- fix for a suspend/resume issue in OMAP
- workaround for a hardware bug to avoid physical damage in OMAP
- really trivial dead code removal in intelfb
* tag 'fbdev-fixes-for-3.3-1' of git://github.com/schandinat/linux-2.6:
atmel_lcdfb: fix usage of CONTRAST_CTR in suspend/resume
intelfb: remove some dead code
drivers/video: compile fixes for fsl-diu-fb.c
OMAPDSS: HDMI: PHY burnout fix
OMAP: 4430SDP/Panda: add HDMI HPD gpio
OMAP: 4430SDP/Panda: setup HDMI GPIO muxes
OMAPDSS: remove wrong HDMI HPD muxing
OMAP: 4430SDP/Panda: rename HPD GPIO to CT_CP_HPD
OMAP: 4430SDP/Panda: use gpio_free_array to free HDMI gpios
OMAPDSS: use sync versions of pm_runtime_put
.. several days delayed. No reason, I just didn't think of it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPKF4KAAoJEHm+PkMAQRiGw/YH+wXg2DpZUuHeBK52zMGlJBPc
DzX11/Uan3Y07gM0JbDzuVxwjX4vdxR2bV6r1qsLP8JEUnE8jyFC32DBGi5WAht7
F4KU/Uov2Ds5/wzvY4Iuo01C+JftQHXuy/Sbhck1d0LI0yjLejRaw+zuJv0x2/eS
7YqV+KTGE1lDuJs/Gyq1Vqr1g9831AuS1tv/g3gaqBuN6TcPBFCocaVxzwrUc+y6
94h26XbbOhQRIz38oqUkiqAGnvYS61ocyBcEiRHf0dXkNSDIINqlgukvd7YTXouA
jj/w/DWpMRcQuYAgqkrurr9+yWC9hVQcsvvQ5sAQnIPcxoR868sg1pO8Oheq+1g=
=kUzV
-----END PGP SIGNATURE-----
Merge tag 'v3.3-rc2' into depends/rmk/for-armsoc
There were conflicts between fixes going in after 3.3-rc1 and
Russell's stable arm-soc base branch. Resolving it in the dependency
branch so that each topic branch shares the same resolution.
Conflicts:
arch/arm/mach-at91/at91cap9.c
arch/arm/mach-at91/at91sam9g45.c
Call runtime pm APIs pm_runtime_get_sync() and pm_runtime_put()
for enabling/disabling clocks appropriately. Remove syscore_ops and
instead use SET_RUNTIME_PM_OPS macro.
There is no more need to call omap_device_disable_idle_on_suspend
since driver is PM runtime adapted now.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The only bank->type (method) used in the OMAP GPIO driver is MPUIO type as they
need to be handled separately. Identify the same using a flag and remove all
METHOD_* macros.
mpuio_init() function is defined under #ifdefs. It is required only in case
of MPUIO bank type and only when PM operations are supported by it.
This is applicable only in case of OMAP16xx SoC's MPUIO GPIO bank type.
For all the other cases it is a dummy function. Hence clean up the same
and remove all the OMAP SoC specific #ifdefs.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
It is not required to use hard-coded offsets any more in context save and
restore functions and instead use the generic offsets which have been correctly
initialized during device registration.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
By adding level and edge detection register offsets and then initializing them
correctly according to OMAP versions during device registrations we can now remove
lot of revision checks in these functions.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Wakeup enable register offset initialized according to OMAP versions
during device registration. Use this to avoid version checks.
Starting with OMAP4, legacy registers should not be used in combination
with the updated regsiters. Use wkup_en register consistently for
all SoCs wherever applicable.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Remove cpu-is checks while enabling/disabling OMAP GPIO module during a gpio
request/free.
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Non-wakeup GPIOs are available only in OMAP2. Avoid cpu_is checks by making
non_wakeup_gpios as part of pdata.
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Modify omap_gpio_prepare_for_idle() & omap_gpio_resume_after_idle() functions
to handle save context & restore context respectively in the OMAP GPIO driver
itself instead of calling these functions from pm specific files.
For this, in gpio_prepare_for_idle(), call *_get_context_loss_count() and in
gpio_resume_after_idle() call it again. If the count is different, do restore
context.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
In omap3, save/restore context is implemented for GPIO banks 2-6 as GPIO bank1
is in wakeup domain. Instead of identifying bank's power domain by bank id,
use 'loses_context' flag which is filled by pwrdm_can_ever_lose_context()
during dev_init.
For getting the powerdomain pointer, omap_hwmod_get_pwrdm() is used.
omap_device_get_pwrdm() could not be used as the pwrdm information needs to be
filled in pdata, whereas omap_device_get_pwrdm() could be used only after
omap_device_build() call.
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The gpio_bank_count is the count of number of GPIO devices in a SoC. Remove this
dependency from the driver by using list. Also remove the dependency on array of
pointers to gpio_bank struct of all GPIO devices.
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Add missing iounmap in error handling code, in a case where the function
already preforms iounmap on some other execution path.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
statement S,S1;
int ret;
@@
e = \(ioremap\|ioremap_nocache\)(...)
... when != iounmap(e)
if (<+...e...+>) S
... when any
when != iounmap(e)
*if (...)
{ ... when != iounmap(e)
return ...; }
... when any
iounmap(e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Tony Lindgren <tony@atomide.com>
pdata needs to be freed before leaving the function in an error case.
A simplified version of the semantic match that finds the problem is as
follows: (http://coccinelle.lip6.fr)
// <smpl>
@r exists@
local idexpression x;
statement S;
identifier f1;
position p1,p2;
expression *ptr != NULL;
@@
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...x...+> }
x->f1
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently MMC2 setup code can only enable loopback clock and
relies on reset value for boards that need to have it disabled.
This causes a problem with certain bootloaders that always enable
that clock, resulting with unwanted bootloader dependencies.
Fix this by making it disable the clock if board data says so.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
hsmmc23_before_set_reg() can set MMCSDIO2ADPCLKISEL bit, which
enables internal clock for MMC2. Currently this function is also called
by code handling MMC3, and if .internal_clock is set in platform data
(by default it currently is), it will set MMCSDIO2ADPCLKISEL for MMC2
instead of MMC3 (MMC3 doesn't have such bit so nothing actually needs to
be done). This breaks 2nd SD slot on pandora.
Fix this by changing hsmmc23_before_set_reg() to only handle MMC2.
Note that this removes .remux() call for MMC3, but no board currently
needs it and it's also not called for MMC4 and MMC5.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
following statement can only change device size from 8-bit(0) to 16-bit(1),
but not vice versa:
regval |= GPMC_CONFIG1_DEVICESIZE(wval);
so as this field has 1 reserved bit, that could be used in future,
just clear both bits and then OR with the desired value
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 2f0778af (ARM: 7205/2: sched_clock: allow sched_clock to be
selected at runtime) had a typo for the case when CONFIG_OMAP_32K_TIMER
is not set.
In dmtimer_read_sched_clock(), wrong argument was getting passed to
__omap_dm_timer_read_counter() function call; instead of "&clksrc",
we were passing "clksrc.io_base", which results into kernel crash.
To reproduce kernel crash, just disable the CONFIG_OMAP_32K_TIMER config
option (and DEBUG_LL) and build/boot the kernel.
This will use dmtimer as a kernel clocksource and lead to kernel
crash during boot -
[ 0.000000] OMAP clocksource: GPTIMER2 at 26000000 Hz
[ 0.000000] sched_clock: 32 bits at 26MHz, resolution 38ns, wraps every
165191ms
[ 0.000000] Unable to handle kernel paging request at virtual address
00030ef1
[ 0.000000] pgd = c0004000
[ 0.000000] [00030ef1] *pgd=00000000
[ 0.000000] Internal error: Oops: 5 [#1] SMP
[ 0.000000] Modules linked in:
[ 0.000000] CPU: 0 Not tainted (3.3.0-rc1-11574-g0c76665-dirty #3)
[ 0.000000] PC is at dmtimer_read_sched_clock+0x18/0x4c
[ 0.000000] LR is at update_sched_clock+0x10/0x84
[ 0.000000] pc : [<c00243b8>] lr : [<c0018684>] psr: 200001d3
[ 0.000000] sp : c0641f38 ip : c0641e18 fp : 0000000a
[ 0.000000] r10: 151c3303 r9 : 00000026 r8 : 76276259
[ 0.000000] r7 : 00028547 r6 : c065ac80 r5 : 431bde82 r4 : c0655968
[ 0.000000] r3 : 00030ef1 r2 : fb032000 r1 : 00000028 r0 : 00000001
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
PandaBoard has twl6040 codec for audio.
Register the omap4-abe-twl6040 platform device.
Add platform data to enable the twl6040 codec.
Since there is a difference in audio between PandaBoard 4430
and PandaBoard ES (4460):
Use different name for the sound card:
"PandaBoard" for PandaBoard 4430
"PandaBoardES" for PandaBoard ES
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: Santosh Shilimkar <santosh.shilimkar@ti.com>
CC: David Anders <x0132446@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
To avoid breakage in audio support with the coming change
in ASoC machine driver (conversion to platfrom device).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
A hardware bug in the OMAP4 HDMI PHY causes physical damage to the board
if the HDMI PHY is kept powered on when the cable is not connected.
This patch solves the problem by adding hot-plug-detection into the HDMI
IP driver. This is not a real HPD support in the sense that nobody else
than the IP driver gets to know about the HPD events, but is only meant
to fix the HW bug.
The strategy is simple: If the display device is turned off by the user,
the PHY power is set to OFF. When the display device is turned on by the
user, the PHY power is set either to LDOON or TXON, depending on whether
the HDMI cable is connected.
The reason to avoid PHY OFF when the display device is on, but the cable
is disconnected, is that when the PHY is turned OFF, the HDMI IP is not
"ticking" and thus the DISPC does not receive pixel clock from the HDMI
IP. This would, for example, prevent any VSYNCs from happening, and
would thus affect the users of omapdss. By using LDOON when the cable is
disconnected we'll avoid the HW bug, but keep the HDMI working as usual
from the user's point of view.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Both Panda and 4430SDP use GPIO 63 as HDMI hot-plug-detect. Configure
this GPIO in the board files.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The HDMI GPIO pins LS_OE and CT_CP_HPD are not currently configured.
This patch configures them as output pins.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
"hdmi_hpd" pin is muxed to INPUT and PULLUP, but the pin is not
currently used, and in the future when it is used, the pin is used as a
GPIO and is board specific, not an OMAP4 wide thing.
So remove the muxing for now.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The GPIO 60 on 4430sdp and Panda is not HPD GPIO, as currently marked in
the board files, but CT_CP_HPD, which is used to enable/disable HPD
functionality.
This patch renames the GPIO.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Instead of freeing the GPIOs individually, use gpio_free_array().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
dss_core has to be initialized before any other DSS hwmod. Currently
this is broken as dss_core is listed in chip/revision specific hwmod
lists while other DSS hwmods are listed in common list which is
registered first.
This patch moves DSS hwmods (except for dss_core) to the separate list
which is registered last to ensure that dss_core is already registered.
This solves the problem with BUG() in L3 interrupt handler on boards
with DSS enabled in bootloader.
The long-term fix to this is to ensure modules are set up in dependency
order in the hwmod core code.
CC: Tomi Valkeinen <tomi.valkeinen@ti.com>
CC: Archit Taneja <archit@ti.com>
CC: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
[paul@pwsan.com: add notes that this is just a temporary workaround until
hwmod dependencies are added]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit 22f51371f8 ("ARM: OMAP3: pm: use
prcm chain handler") breaks the build on a 2420-only config, due to
a missing include for plat/irqs.h:
CC arch/arm/mach-omap2/prm2xxx_3xxx.o
arch/arm/mach-omap2/prm2xxx_3xxx.c:41:11: error: 'INT_34XX_PRCM_MPU_IRQ' undeclared here (not in a function)
Fix by explicitly including it.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Commit 7b250aff1c ("ARM: OMAP: Avoid
cpu_is_omapxxxx usage until map_io is done") breaks the build on a
2420-only config on v3.3-rc1:
arch/arm/mach-omap2/built-in.o: In function `omap2430_init_early':
arch/arm/mach-omap2/io.c:406: undefined reference to `omap2_set_globals_243x'
arch/arm/mach-omap2/io.c:410: undefined reference to `omap243x_clockdomains_init'
arch/arm/mach-omap2/io.c:411: undefined reference to `omap2430_hwmod_init'
Fix by only compiling omap2420_init_early() when CONFIG_SOC_OMAP2420
is selected, and only compiling omap2430_init_early() when
CONFIG_SOC_OMAP2430 is selected.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
To be able to get the memory resources by name from
the DMIC driver (for MPU and for DMA).
Without this patch, functionality that was working in 3.2 breaks in
3.3-rc1. This patch should have gone in as part of the 3.3 merge
window, but was inadvertently missed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[paul@pwsan.com: added commit message note]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
dispc's sysc_flags is missing SYSC_HAS_ENAWAKEUP flag. This seems to
cause SYNC_LOST errors from the DSS when the power management is
enabled.
This patch adds the missing SYSC_HAS_ENAWAKEUP flag. Note that there are
other flags missing also (clock activity, DSI's sysc flags), but as they
are not critical, they will be fixed in the next merge window.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Currently OMAP2 and 3 share the same omap_hwmod_class and
omap_hwmod_class_sysconfig for dispc. However, OMAP3 has sysconfig
bits that OMAP2 doesn't have, so we need to split those structs into
OMAP2 and OMAP3 specific versions.
This patch only splits the structs, without changing the contents.
This is a prerequisite for a subsequent fix.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[paul@pwsan.com: added commit note]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
To ensure correct alignment of cacheline-aligned data, the maximum
cacheline size needs to be known at compile time.
Since Cortex-A8 and Cortex-A15 have 64-byte cachelines (and it is likely
that there will be future ARMv7 implementations with the same line size)
then it makes sense to assume that CPU_V7 implies a 64-byte L1 cacheline
size. For CPUs with smaller caches, this will result in some harmless
padding but will help with single zImage work and avoid hitting subtle
bugs with misaligned data structures.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When this is the only content remaining in mach/system.h then the
whole file is removed.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-and-tested-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: David Brown <davidb@codeaurora.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
