When a software reset is performed on the AD2S1210 to make the selected
excitation frequency take effect, it always triggers faults on the
input signals because the output signal is interrupted momentarily.
So we need to clear the faults after the software reset to avoid
triggering fault events the next time a sample is read.
The datasheet specifies a time t[track] in Table 27 that specifies the
settle time in milliseconds after a reset depending on the selected
resolution. This is used in the driver to add an appropriate delay.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20231010-ad2s1210-mainline-v5-2-35a0f6ffa04a@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This refactors the sample line toggle in the ad2s1210 resolver driver
to a separate function. The sample has some timing requirements, so
this ensures that it is always done the same way, both in the existing
call sites and any future usage.
Previously, the sample line was kept on for the duration of the read,
but this is not necessary. Data is latched in on the rising edge and
after the specified delay the state of the sample line does not matter.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20231010-ad2s1210-mainline-v5-1-35a0f6ffa04a@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Faults have been converted to events and we are now polling the fault
register each time we read a sample, so we no longer need the fault
attribute.
This attribute was not suitable for promotion out of staging anyway
since it was returning multiple values in a single attribute.
The fault clearing feature should not be needed unless we need to
support the fault output pins on the chip which is not currently
supported. So we can add this feature back in if we need it later.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20231005-ad2s1210-mainline-v4-16-ec00746840fc@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ad2s1210 resolver driver has quite a few channels, mostly for
internal signals for event support. This makes it difficult to know
which channel is which. This patch adds a label attribute to the
channels to make it easier to identify them.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20231005-ad2s1210-mainline-v4-15-ec00746840fc@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ad2s1210 driver shoe-horns the register and fault support into IIO
events. The mapping between the registers/faults and the events is not
obvious. To save users from having to read the entire driver to figure
out how to use it, add a summary of the register/fault support to the
top of the file.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20231005-ad2s1210-mainline-v4-14-ec00746840fc@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When reading the position and velocity on the AD2S1210, there is also a
3rd byte following the two data bytes that contains the fault flag bits.
This patch adds support for reading this byte and generating events when
faults occur.
The faults are mapped to various channels and event type in order to
have a unique event for each fault.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20231005-ad2s1210-mainline-v4-13-ec00746840fc@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD2S1210 has a programmable threshold for the degradation of signal
(DOS) mismatch fault. This fault is triggered when the difference in
amplitude between the sine and cosine inputs exceeds the threshold.
The DOS reset min/max registers on the chip provide initial values
for internal tracking of the min/max of the monitor signal after the
fault register is cleared.
This patch converts the custom device DOS reset min/max threshold
attributes custom event attributes on the monitor signal channel.
The attributes now use millivolts instead of the raw register value in
accordance with the IIO ABI.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20231005-ad2s1210-mainline-v4-11-ec00746840fc@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD2S1210 has a programmable threshold for the degradation of signal
(DOS) mismatch fault. This fault is triggered when the difference in
voltage between the sine and cosine inputs exceeds the threshold. In
other words, when the magnitude of sine and cosine inputs are equal,
the AC component of the monitor signal is zero and when the magnitudes
of the sine and cosine inputs are not equal, the AC component of the
monitor signal is the difference between the sine and cosine inputs.
So the fault occurs when the magnitude of the AC component of the
monitor signal exceeds the DOS mismatch threshold voltage.
This patch converts the custom device DOS mismatch threshold attribute
to an event magnitude attribute on the monitor signal channel.
The attribute now uses millivolts instead of the raw register value in
accordance with the IIO ABI.
Emitting the event will be implemented in a later patch.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20231005-ad2s1210-mainline-v4-10-ec00746840fc@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD2S1210 has a programmable threshold for the degradation of signal
(DOS) overrange fault. This fault is triggered when either the sine or
cosine input rises above the threshold voltage.
This patch converts the custom device DOS overrange threshold attribute
to an event rising edge threshold attribute on the monitor signal
channel.
The attribute now uses millivolts instead of the raw register value in
accordance with the IIO ABI.
Emitting the event will be implemented in a later patch.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20231005-ad2s1210-mainline-v4-9-ec00746840fc@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD2S1210 has a programmable threshold for the loss of signal (LOS)
fault. This fault is triggered when either the sine or cosine input
falls below the threshold voltage.
This patch converts the custom device LOS threshold attribute to an
event falling edge threshold attribute on a new monitor signal channel.
The monitor signal is an internal signal that combines the amplitudes
of the sine and cosine inputs as well as the current angle and position
output. This signal is used to detect faults in the input signals.
The attribute now uses millivolts instead of the raw register value in
accordance with the IIO ABI.
Emitting the event will be implemented in a later patch.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20231005-ad2s1210-mainline-v4-8-ec00746840fc@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD2S1210 monitors the internal error signal (difference between
estimated angle and measured angle) to determine a loss of position
tracking (LOT) condition. When the error value exceeds a threshold, a
fault is triggered. This threshold is user-configurable.
This patch converts the custom lot_high_thrd and lot_low_thrd attributes
in the ad2s1210 driver to standard event attributes. This will allow
tooling to be able to expose these in a generic way.
Since the low threshold determines the hysteresis, it requires some
special handling to expose the difference between the high and low
register values as the hysteresis instead of exposing the low register
value directly.
The attributes also return the values in radians now as required by the
ABI.
Actually emitting the fault event will be done in a later patch.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20231005-ad2s1210-mainline-v4-7-ec00746840fc@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD2S1210 chip has a phase lock range feature that allows selecting
the allowable phase difference between the excitation output and the
sine and cosine inputs. This can be set to either 44 degrees (default)
or 360 degrees.
This patch adds a new phase channel with a phase0_mag_rising event that
can be used to configure the phase lock range. Actually emitting the
event will be added in a subsequent patch.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20231005-ad2s1210-mainline-v4-5-ec00746840fc@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Selecting the resolution was implemented as the `bits` sysfs attribute.
However, the selection of the resolution depends on how the hardware
is wired and the specific application, so this is rather a job for
devicetree to describe.
A new devicetree property `assigned-resolution-bits` to specify the
resolution required for each chip is added and the `bits` sysfs
attribute is removed.
Since the resolution is now supplied by a devicetree property, the
resolution-gpios are now optional and we can allow for the case where
the resolution pins on the AD2S1210 are hard-wired instead of requiring
them to be connected to gpios.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20231005-ad2s1210-mainline-v4-4-ec00746840fc@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ad2s1210 driver has a device-specific attribute `fexcit` for setting
the frequency of the excitation output. This converts it to a channel in
order to use standard IIO ABI.
The excitation frequency is an analog output that generates a sine wave.
Only the frequency is configurable. According to the datasheet, the
specified range of the excitation frequency is from 2 kHz to 20 kHz and
can be set in increments of 250 Hz.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20231005-ad2s1210-mainline-v4-3-ec00746840fc@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD2S1210 resolver has a hysteresis feature that can be used to
prevent flicker in the LSB of the position register. This can be either
enabled or disabled. Disabling hysteresis is useful for increasing
precision by oversampling.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20231005-ad2s1210-mainline-v4-2-ec00746840fc@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When reading registers on the AD2S1210 chip, we have to supply a "dummy"
address for the second SPI tx byte so that we don't accidentally write
to a register. This register will be read and the value discarded on the
next regmap read or write call.
Reading the fault register has a side-effect of clearing the faults
so we should not use this register for the dummy read.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20231005-ad2s1210-mainline-v4-1-ec00746840fc@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This modifies the ad2s1210_show_fexcit() function to read the excitation
frequency from the control register. This way we don't have to keep
track of the value and don't risk returning a stale value.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20230929-ad2s1210-mainline-v3-16-fa4364281745@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This combines the ad2s1210_update_frequency_control_word() and
ad2s1210_soft_reset() functions into a single function since they
both have to be called together. (The software reset does not reset
any configuration registers, it only updates the excitation output
and resets the tracking loop.)
Also clean up a few things while touching this:
- move AD2S1210_DEF_EXCIT macro with similar macros
- remove unnecessary dev_err() calls
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20230929-ad2s1210-mainline-v3-15-fa4364281745@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
- Remove "adi," prefix from gpio names.
- Sample gpio is now expected to be active low.
- Convert A0 and A1 gpios to "mode-gpios" gpio array.
- Convert RES0 and RES1 gpios to "resolution-gpios" gpio array.
- Remove extraneous lookup tables.
- Remove unused mode field from state struct.
- Swap argument order of ad2s1210_set_mode() while we are touching this.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20230929-ad2s1210-mainline-v3-13-fa4364281745@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This removes the config register sysfs attribute.
Writing to the config register directly can be dangerous and userspace
should not need to have to know the register layout. This register
can still be accessed though debugfs if needed.
We can add new attributes to set specific flags in the config register
in the future if needed (e.g. `enable_hysterisis` and
`phase_lock_range`).
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20230929-ad2s1210-mainline-v3-12-fa4364281745@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This makes use of the regmap API to read and write the configuration
registers. This simplifies code quite a bit and makes it safer
(previously, it was easy to write a bad value to the config registers
which causes the chip to lock up and need to be reset).
This chip has multiple modes of operation. In normal mode, we do not use
regmap since there is no addressing - data is just bitshifted out during
the SPI read. In config mode, we use regmap since it requires writing
the address (with read/write flag) before reading and writing.
We don't use the lock provided by the regmap because we need to also
synchronize with the normal mode SPI reads and with the various GPIOs.
There is also a quirk when reading registers (other than the fault
register). If the address/data bit is set in the value read, then it
indicates there is a configuration parity error and the data is not
valid. Previously, this was checked in a few places, but not
consistently. Now, we always check it in the regmap read function.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20230929-ad2s1210-mainline-v3-10-fa4364281745@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This removes the fclkin sysfs attribute and replaces it with getting
the CLKIN clock rate using the clk subsystem (i.e. from the devicetree).
CLKIN comes from an external oscillator that is connected directly to
the AD2S1210 chip, so users of the sysfs attributes should not need to
be concerned with this.
The fclkin field (the datasheet name) is renamed to clkin_hz to be more
obvious that it is a frequency in Hz.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20230929-ad2s1210-mainline-v3-9-fa4364281745@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This adds an implementation of IIO_CHAN_INFO_SCALE to the ad2s1210
resolver driver. This allows userspace to get the scale factor for the
raw values.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20230929-ad2s1210-mainline-v3-8-fa4364281745@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This removes the special handling for resolutions lower than 16 bits.
This will allow us to use a fixed scale independent of the resolution.
A new sample field is added to store the raw data instead of reusing
the config mode rx buffer so that we don't have to do a cast or worry
about unaligned access.
Also, for the record, according to the datasheet, the logic for the
special handling based on hysteresis that was removed was incorrect.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20230929-ad2s1210-mainline-v3-7-fa4364281745@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This adds a check to the return value of ad2s1210_initial() since it
can fail. The call is also moved before devm_iio_device_register() so
that we don't have to unregister the device if it fails.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20230929-ad2s1210-mainline-v3-4-fa4364281745@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This removes the call to spi_setup() in the ad2s1210 driver.
Setting MODE_3 was incorrect. It should be MODE_1 but we can let the
device tree select this and avoid the need to call spi_setup().
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20230929-ad2s1210-mainline-v3-3-fa4364281745@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This fixes a use before initialization in ad2s1210_probe(). The
ad2s1210_setup_gpios() function uses st->sdev but it was being called
before this field was initialized.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20230929-ad2s1210-mainline-v3-2-fa4364281745@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In theory, this code path should not be reachable because of the
previous switch statement. But just in case we should make sure we
are restoring the SAMPLE gpio to its original state before returning
in addition to releasing the mutex lock.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20230921144400.62380-5-dlechner@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When reading the fault attribute, an empty string was printed if the
fault register value was non-zero.
This is fixed by checking that the return value is less than zero
instead of not zero.
Also always print two hex digits while we are touching this line.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20230921144400.62380-4-dlechner@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The devm_clk_get_enabled() helper:
- calls devm_clk_get()
- calls clk_prepare_enable() and registers what is needed in order to
call clk_disable_unprepare() when needed, as a managed resource.
This simplifies the code and avoids the need of a dedicated function used
with devm_add_action_or_reset().
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://lore.kernel.org/r/20230825095612.2972892-1-ruanjinjie@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
After commit b8a1a4cd5a ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498 ("i2c: Switch .probe() to not take an id parameter") convert
back to (the new) .probe() to be able to eventually drop .probe_new() from
struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230524151646.486847-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Here is the "big" set of char/misc and other driver subsystems for
6.4-rc1.
It's pretty big, but due to the removal of pcmcia drivers, almost breaks
even for number of lines added vs. removed, a nice change.
Included in here are:
- removal of unused PCMCIA drivers (finally!)
- Interconnect driver updates and additions
- Lots of IIO driver updates and additions
- MHI driver updates
- Coresight driver updates
- NVMEM driver updates, which required some OF updates
- W1 driver updates and a new maintainer to manage the subsystem
- FPGA driver updates
- New driver subsystem, CDX, for AMD systems
- lots of other small driver updates and additions
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZEp5Eg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynSXgCg0kSw3vUYwpsnhAsQkoPw1QVA23sAn2edRCMa
GEkPWjrROueCom7xbLMu
=eR+P
-----END PGP SIGNATURE-----
Merge tag 'char-misc-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc drivers updates from Greg KH:
"Here is the "big" set of char/misc and other driver subsystems for
6.4-rc1.
It's pretty big, but due to the removal of pcmcia drivers, almost
breaks even for number of lines added vs. removed, a nice change.
Included in here are:
- removal of unused PCMCIA drivers (finally!)
- Interconnect driver updates and additions
- Lots of IIO driver updates and additions
- MHI driver updates
- Coresight driver updates
- NVMEM driver updates, which required some OF updates
- W1 driver updates and a new maintainer to manage the subsystem
- FPGA driver updates
- New driver subsystem, CDX, for AMD systems
- lots of other small driver updates and additions
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (196 commits)
mcb-lpc: Reallocate memory region to avoid memory overlapping
mcb-pci: Reallocate memory region to avoid memory overlapping
mcb: Return actual parsed size when reading chameleon table
kernel/configs: Drop Android config fragments
virt: acrn: Replace obsolete memalign() with posix_memalign()
spmi: Add a check for remove callback when removing a SPMI driver
spmi: fix W=1 kernel-doc warnings
spmi: mtk-pmif: Drop of_match_ptr for ID table
spmi: pmic-arb: Convert to platform remove callback returning void
spmi: mtk-pmif: Convert to platform remove callback returning void
spmi: hisi-spmi-controller: Convert to platform remove callback returning void
w1: gpio: remove unnecessary ENOMEM messages
w1: omap-hdq: remove unnecessary ENOMEM messages
w1: omap-hdq: add SPDX tag
w1: omap-hdq: allow compile testing
w1: matrox: remove unnecessary ENOMEM messages
w1: matrox: use inline over __inline__
w1: matrox: switch from asm to linux header
w1: ds2482: do not use assignment in if condition
w1: ds2482: drop unnecessary header
...
Here is the large set of staging driver updates for 6.4-rc1. Once
again, we removed more code than was added, a nice trend.
It was a calm cycle, mostly all just small coding style cleanups,
included in here are:
- removal of the greybus loopback testing tools, userspace code that
didn't belong in a driver subdirectory and was causing problems for
some build systems
- platform remove callback cleanups
- rtl8192e huge cleanups
- other small staging driver cleanups.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZEp8GA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynwpQCeLF95LYh09qG+H4uKNLfjkS/AHR0AnAkuaH/4
4q0UhHX+jDeRFaat3qtN
=VHqC
-----END PGP SIGNATURE-----
Merge tag 'staging-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver updates from Greg KH:
"Here is the large set of staging driver updates for 6.4-rc1. Once
again, we removed more code than was added, a nice trend.
It was a calm cycle, mostly all just small coding style cleanups,
included in here are:
- removal of the greybus loopback testing tools, userspace code that
didn't belong in a driver subdirectory and was causing problems for
some build systems
- platform remove callback cleanups
- rtl8192e huge cleanups
- other small staging driver cleanups.
All of these have been in linux-next for a while with no reported
problems"
* tag 'staging-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (185 commits)
staging: rtl8192e: Fix W_DISABLE# does not work after stop/start
staging: rtl8192e: Remove unchanged variables bfsync_processing and more
staging: rtl8192e: Remove unchanged variable frame_sync_monitor
staging: rtl8192e: Remove unchanged variable chan_forced
staging: rtl8192e: Remove set to true while true of bfirst_after_down
staging: rtl8192e: Remove second initialization of bActuallySet
staging: rtl8192e: Remove unused macro RT_SET_PS_LEVEL
staging: rtl8192e: Remove unused function rtl92e_disable_nic
staging: rtl8192e: Remove unchanged variable RegRfPsLevel
staging: rtl8172: Add blank lines after declarations
staging: rtl8192e: Remove unused variable RF_Type
staging: rtl8192e: Remove one of two checks for hardware RTL8192SE
staging: rtl8192e: Remove unused function _rtl92e_dm_init_wa_broadcom_iot
staging: rtl8192e: Remove macro IS_HARDWARE_TYPE_8192SE
staging: greybus: drop loopback test files
staging: rtl8192e: Add blank lines after declarations
staging: rtl8192e: avoid CamelCase <dot11RSNAStatsCCMPDecryptErrors>
staging: rtl8192e: avoid CamelCase <dot11RSNAStatsCCMPReplays>
staging: rtl8192e: avoid CamelCase <dot11RSNAStatsCCMPFormatErrors>
staging: rtl8192e: fix alignment to match open parenthesis
...
With linux/acpi.h no longer implicitly including of.h, add an explicit
include of of.h to fix the following error:
drivers/staging/iio/resolver/ad2s1210.c:706:21: error: implicit declaration of function 'of_match_ptr' is invalid in C99 [-Werror,-Wimplicit-function-declaration]
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This driver is so far from making correct use of the IIO infrastructure
and ABI that if someone wanted to make the driver suitable for moving
out of staging, they would more or less be starting from scratch.
As such there is little point in keeping the existing code in staging.
Note this was only user of the meter.h header so that is dropped.
There are no other drivers in the staging/iio/meter directory so drop
the build system files as well.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20230129160805.747745-1-jic23@kernel.org
Call '__adis_initial_startup()' instead of its locked variant in
'adis16240_probe()'.
The locks are not needed at this point.
Signed-off-by: Ramona Bolboaca <ramona.bolboaca@analog.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20221122082757.449452-9-ramona.bolboaca@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Call '__adis_initial_startup()' instead of its locked variant in
'adis16203_probe()'.
The locks are not needed at this point.
Signed-off-by: Ramona Bolboaca <ramona.bolboaca@analog.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20221122082757.449452-8-ramona.bolboaca@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-569-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-568-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-567-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Replace ternary operator by simple if based evaluation of the return
value. Issue identified using coccicheck.
Signed-off-by: Deepak R Varma <drv@mailo.com>
Link: https://lore.kernel.org/r/Y3CAdCa17WdWDYUa@qemulion
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Improve code readability by merging unnecessary split lines that are
well within the code-style guidelines post merge.
Signed-off-by: Deepak R Varma <drv@mailo.com>
Acked-by: Julia Lawall <julia.lawall@inria.fr>
Link: https://lore.kernel.org/r/Y0z2/qFe3kW96MTs@debian-BULLSEYE-live-builder-AMD64
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
