Some variants of Goodix touchscreen firmwares use 9-bytes finger
report format instead of common 8-bytes format.
This report format may be present as:
struct goodix_contact_data {
uint8_t unknown1;
uint8_t track_id;
uint8_t unknown2;
uint16_t x;
uint16_t y;
uint16_t w;
}__attribute__((packed));
Add support for such format and use it for Lenovo Yoga Book notebook
(which uses a Goodix touchpad as a touch keyboard).
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 315 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190115.503150771@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GT5663 is capacitive touch controller with customized smart
wakeup gestures.
Add support for it by adding compatible and supported chip data.
The chip data on GT5663 is similar to GT1151, like
- config data register has 0x8050 address
- config data register max len is 240
- config data checksum has 16-bit
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Goodix CTP controllers require AVDD28, VDDIO regulators for power-on
sequence.
The delay between these regualtor operations as per Power-on Timing
from datasheet[1] is 0 (T1 >= 0 usec).
So, enable and disable these regulators in proper order using normal
regulator functions without any delay in between.
[1] GT5663 Datasheet_English_20151106_Rev.01
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
"Invalid config" gives little idea what's wrong. Print the values that
must not be 0 so we know which ones are off.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
GPD Win 2 Website: http://www.gpd.hk/gpdwin2.asp
Tested on a unit from the first production run sent to Indiegogo backers
Signed-off-by: Ethan Lee <flibitijibibo@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use touchscreen_properties structure instead of implementing all
properties by our own. It allows us to reuse generic code for parsing
device-tree properties (which was implemented manually in the driver for
now). Additionally, it allows us to report events using generic
touchscreen_report_pos(), which automatically handles inverted and
swapped axes.
This fixes the issue with the custom code incorrectly handling case where
ts->inverted_x and ts->swapped_x_y were true, but ts->inverted_y was
false. Assuming we have 720x1280 touch panel, ts->abs_x_max == 1279 and
ts->abs_y_max == 719 (because we inverted that in goodix_read_config()).
Now let's assume that we received event from (0:0) position (in touch
panel original coordinates). In function goodix_ts_report_touch() we
calculate input_x as 1279, but after swapping input_y takes that value
(which is more that maximum 719 value reported during initialization).
Note that since touchscreen coordinates are 0-indexed, we now report
touchscreen range as (0:size-1).
Developed and tested on custom DT-based device with gt1151 touch
panel.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
[dtor: fix endianness annotation reported by sparse, handle errors when
initializing MT slots]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We should not try to do any i2c transfers before the controller is
resumed (which happens before our resume method gets called).
So we need to disable our IRQ while suspended to enforce this. The
code paths for devices with GPIOs for the int and reset pins already
disable the IRQ the through goodix_free_irq().
This commit also disables the IRQ while suspended for devices without
GPIOs for the int and reset pins.
This fixes the i2c bus sometimes getting stuck after a suspend/resume
causing the touchscreen to sometimes not work after a suspend/resume.
This has been tested on a GPD pocked device.
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://www.reddit.com/r/GPDPocket/comments/7niut2/fix_for_broken_touch_after_resume_all_linux/
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Support was added based on Goodix GitHub repo [1]. There are two major
differences between gt1151 and currently supported devices (gt9x):
* CONFIG_DATA register has 0x8050 address instead of 0x8047,
* config data checksum has 16-bit width instead of 8-bit.
Also update goodix_i2c_test() function, so it reads ID register (which
has the same address for all devices) instead of CONFIG_DATA (because
its address is known only after reading ID of the device).
[1] https://github.com/goodix/gt1x_driver_generic
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Goodix panel triggers an interrupt on touch events. However, its
registers will contain the valid values a short time after the
interrupt, and not when it's raised. At that moment, the 'buffer status'
bit is set.
Previously, if the 'buffer status' bit was not set when the registers
were read, the data was discarded and no input event was emitted,
causing "finger down" or "finger up" events to be missed sometimes.
This went unnoticed until v4.9, as the DesignWare I2C driver commonly
used with this driver had enough latency for that bug to never trigger
until commit 2702ea7dbe ("i2c: designware: wait for disable/enable only
if necessary").
Now, in the IRQ handler we will poll (with a timeout) the 'buffer status'
bit and process the data of the panel as soon as this bit gets set.
Note that the Goodix panel will send a few spurious interrupts after the
'finger up' event, in which the 'buffer status' bit will never be set.
Cc: Bastien Nocera <hadess@hadess.net>
Cc: russianneuromancer@ya.ru
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
[hdegoede@redhat.com: Change poll loop to use jiffies,
add comment about typical poll time]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[dtor: rearranged control flow a bit to avoid explicit goto and double
check]
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On some x86 tablets with a Goodix touchscreen, the Windows logo on the
front is a capacitive home button. Touching this button results in a touch
with bit 4 of the first byte set, while only the lower 4 bits (0-3) are
used to indicate the number of touches.
Report a KEY_LEFTMETA press when this happens.
Note that the hardware might support more than one button, in which
case the "id" byte of coor_data would identify the button in question.
This is not implemented as we don't have access to hardware with
multiple buttons.
Signed-off-by: Sergei A. Trusov <sergei.a.trusov@ya.ru>
Acked-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The goodix touchscreen driver uses a "rotated_screen" flag for
systems on which the touchscreen is mounted rotated by 180
degrees with respect to the display. With the addition of
support for the dt properties "touchscreen-inverted-x" and
"touchscreen-inverted-y", a separate "rotated_screen" flag
is not necessary anymore. This patch replaces it by setting
the inverted_x and inverted_y flags instead.
Signed-off-by: Karsten Merker <merker@debian.org>
Reviewed-by: Irina Tirdea <irina.tirdea@intel.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Acked-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Implement support for the following device-tree and ACPI 5.1 DSD
properties in the goodix touchscreen driver:
- touchscreen-inverted-x: X axis is inverted (boolean)
- touchscreen-inverted-y: Y axis is inverted (boolean)
- touchscreen-swapped-x-y: X and Y axis are swapped (boolean)
These are necessary on tablets which have a display in portrait
format while the touchscreen is in landscape format, such as e.g.
the MSI Primo 81.
Signed-off-by: Karsten Merker <merker@debian.org>
Tested-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Irina Tirdea <irina.tirdea@intel.com> (with ACPI DSD properties)
Tested-by: Aleksei Mamlin <mamlinav@gmail.com> (with device-tree properties)
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Implement suspend/resume for goodix driver.
The suspend and resume process uses the gpio pins. If the device ACPI/DT
information does not declare gpio pins, suspend/resume will not be
available for these devices.
This is based on Goodix datasheets for GT911 and GT9271 and on Goodix
driver gt9xx.c for Android (publicly available in Android kernel trees for
various devices).
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Goodix devices can be configured by writing custom data to the device at
init. The configuration data is read with request_firmware from
"goodix_<id>_cfg.bin", where <id> is the product id read from the device
(e.g.: goodix_911_cfg.bin for Goodix GT911, goodix_9271_cfg.bin for
GT9271).
The configuration information has a specific format described in the Goodix
datasheet. It includes X/Y resolution, maximum supported touch points,
interrupt flags, various sensitivity factors and settings for advanced
features (like gesture recognition).
Before writing the firmware, it is necessary to reset the device. If
the device ACPI/DT information does not declare gpio pins (needed for
reset), writing the firmware will not be available for these devices.
This is based on Goodix datasheets for GT911 and GT9271 and on Goodix
driver gt9xx.c for Android (publicly available in Android kernel
trees for various devices).
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
After power on, it is recommended that the driver resets the device.
The reset procedure timing is described in the datasheet and is used
at device init (before writing device configuration) and
for power management. It is a sequence of setting the interrupt
and reset pins high/low at specific timing intervals. This procedure
also includes setting the slave address to the one specified in the
ACPI/device tree.
This is based on Goodix datasheets for GT911 and GT9271 and on Goodix
driver gt9xx.c for Android (publicly available in Android kernel
trees for various devices).
For reset the driver needs to control the interrupt and
reset gpio pins (configured through ACPI/device tree). For devices
that do not have the gpio pins properly declared, the functionality
depending on these pins will not be available, but the device can still
be used with basic functionality.
For both device tree and ACPI, the interrupt gpio pin configuration is
read from the "irq-gpios" property and the reset pin configuration is
read from the "reset-gpios" property. For ACPI 5.1, named properties
can be specified using the _DSD section. This functionality will not be
available for devices that use indexed gpio pins declared in the _CRS
section (we need to provide backward compatibility with devices
that do not support using the interrupt gpio pin as output).
For ACPI, the pins can be specified using ACPI 5.1:
Device (STAC)
{
Name (_HID, "GDIX1001")
...
Method (_CRS, 0, Serialized)
{
Name (RBUF, ResourceTemplate ()
{
I2cSerialBus (0x0014, ControllerInitiated, 0x00061A80,
AddressingMode7Bit, "\\I2C0",
0x00, ResourceConsumer, ,
)
GpioInt (Edge, ActiveHigh, Exclusive, PullNone, 0x0000,
"\\I2C0", 0x00, ResourceConsumer, ,
)
{ // Pin list
0
}
GpioIo (Exclusive, PullDown, 0x0000, 0x0000,
IoRestrictionOutputOnly, "\\I2C0", 0x00,
ResourceConsumer, ,
)
{
1
}
})
Return (RBUF)
}
Name (_DSD, Package ()
{
ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package ()
{
Package (2) {"irq-gpios", Package() {^STAC, 0, 0, 0 }},
Package (2) {"reset-gpios", Package() {^STAC, 1, 0, 0 }},
...
}
}
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Each of the Goodix devices supported by this driver has a fixed size for
the configuration information registers. The size varies depending on the
device and is specified in the datasheet.
Use the proper configuration length as specified in the datasheet for
each device model, so we do not read more than the actual size of the
configuration registers.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Acked-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So the driver needs to export the I2C table and this
be built into the module or udev won't have the necessary information
to auto load the correct module when the device is added.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The touchscreen on the WinBook TW100 and TW700 don't match the default
display, with 0,0 touches being reported when touching at the bottom
right of the screen.
1280,800 0,800
+-------------+
| |
| |
| |
+-------------+
1280,0 0,0
It's unfortunately impossible to detect this problem with data from the
DSDT, or other auxiliary metadata, so fallback to quirking this specific
model of tablet instead.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
input_mt_init_slots() will do that for us.
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Goodix touchscreens export through their registers a Product ID and
Firmware Version. The Product ID is an ASCII encoding of the product name
(e.g.: "911").
Export to sysfs (through the input subsystem) the product id and firmware
version read from the device rather than using constant values.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Acked-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fix sparse warning:
drivers/input/touchscreen/goodix.c:182:26: warning: Variable length array is used.
Replace the variable length array with fixed length.
Some Goodix devices have maximum 5 touch points, while others have 10 touch
points. Using the maximum length (80 bytes) for all devices will lead to
wasting 40 bytes on stack when using devices with maximum 5 touch points.
However, that is preferable to using kmalloc which will use even more
resources.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Acked-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The MSB of the first byte read via I2C at the coordinates address
indicates whether the data is valid or ready (called "buffer status" in
the datasheets) when an interrupt is raised. Previously, this bit was
ignored, which resulted in a lot of incorrect detections of "finger
removed" events.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This change adds device tree support and binding information for Goodix
GT9xx series touchscreen controller. It also adds support for 5-finger
chips, like GT911 and GT912, which can be found on ARM tablets, such as
Wexler TAB7200 and MSI Primo73.
Datasheets can be found here:
https://drive.google.com/folderview?id=0BxCVOQS3ZymGfmJyY2RKbE5XbVlKNlktVTlwV0lxNEdxd2dzeWZER094cmJPVnMxN1F0Yzg&usp=sharing
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use max number of touches from device config instead of hardcoding.
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Acked-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add a driver for the Goodix touchscreen panel found in Onda v975w tablets.
The driver is based off the Android driver gt9xx.c found in some Android
code dumps, but now bears no resemblance to the original driver.
The driver was tested on the aforementioned tablet.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
