There's some known configurations where the lack of these tables/scripts
is perfectly normal, reduce visibilty of complaint messages to debug.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
sil164 and friends are the most common, usually they just need to be
poked once because a fixed configuration is enough for any modes and
clocks, so they worked without this patch if the BIOS had done a good
job on POST. Display couldn't survive a suspend/resume cycle though.
Unfortunately, BIOS scripts are useless here.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Not very nice, but I don't think there's a simpler workaround.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Leaving the IRQ unack'ed while switching contexts makes the switch
fail randomly on some nv1x.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
nouveau_load() just returned directly if there was an error instead of
releasing resources.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Previously nouveau_mem_reset_agp() was only disabling AGP fast writes
when coming back from suspend. However, the "locked out of the card
because of FW" problem can also be reproduced on init if you
unload/reload nouveau.ko several times. This patch makes the AGP code
reset FW on init.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This makes it easier to see how this is working, and lets us transfer the
EDID in blocks of 16 bytes.
The primary reason for this change is because debug logs are rather hard
to read with the hundreds of single-byte auxch transactions that occur.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Commit 5349ef3127 (drm/fb: fix
FBIOGET/PUT_VSCREENINFO pixel clock handling) changed the logic of
when a pixclock was valid vs invalid.
The atomic kernel mode setting used by the kernel debugger relies upon
the drm_fb_helper_check_var() to always return -EINVAL. Until a
better solution exists, this behavior will be restored.
CC: David Airlie <airlied@linux.ie>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
If the HW compression is left on, the call backs from the HW will
crash the kernel. The only time this code is called is when kernel
mode setting is in use with kgdb and the kdb shell.
The atomic display pipe handler callback will reset everything when
kgdb restores kernel to the run state.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: David Airlie <airlied@linux.ie>
Implement atomic kernel mode settings using the fb layer's debug hook
system for supporting debugger interaction.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Implement the callbacks for KDB entry/exit via the drm helpers.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
This restricts the use of the big kernel lock to the i830 and i810
device drivers. The three remaining users in common code (open, ioctl
and release) get converted to a new mutex, the drm_global_mutex,
making the locking stricter than the big kernel lock.
This may have a performance impact, but only in those cases that
currently don't use DRM_UNLOCKED flag in the ioctl list and would
benefit from that anyway.
The reason why i810 and i830 cannot use drm_global_mutex in their
mmap functions is a lock-order inversion problem between the current
use of the BKL and mmap_sem in these drivers. Since the BKL has
release-on-sleep semantics, it's harmless but it would cause trouble
if we replace the BKL with a mutex.
Instead, these drivers get their own ioctl wrappers that take the
BKL around every ioctl call and then set their own handlers as
DRM_UNLOCKED.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
In most use cases the driver will be using the same static config all
the time: interpreting i2c_board_info::platform_data as the default
config we can can save the GPU driver a redundant set_config() call.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is required should we ever attempt to use an io-mapping where
KM_USER0 is verboten, such as inside an IRQ context.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
R4xx also uses the atom add connector function, but underscan is only
supported on avivo chips.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
v2: Userspace (notably xf86-video-{intel,ati}) became confused when
drmSetInterfaceVersion() started returning -EBUSY as they used a second
call (the first done in drmOpen()) to check their master credentials.
Since userspace wants to be able to repeatedly call
drmSetInterfaceVersion() allow them to do so.
v3: Rebase to drm-core-next.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This connector attribute allows you to enable or disable underscan
on a digital output to compensate for panels that automatically
overscan (e.g., many HDMI TVs). Valid values for the attribute are:
off - forces underscan off
on - forces underscan on
auto - enables underscan if an HDMI TV is connected, off otherwise
default value is auto.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Prior to this patch the code was dividing the src_v by the dst_h
and vice versa, rather than src_v/dst_v and src_h/dst_h.
This could lead to problems in the calculation of the display
watermarks.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'intel/drm-intel-next' of /ssd/git/drm-next: (230 commits)
drm/i915: Clear the Ironlake dithering flags when the pipe doesn't want it.
drm/agp/i915: trim stolen space to 32M
drm/i915: Unset cursor if out-of-bounds upon mode change (v4)
drm/i915: Unreference object not handle on creation
drm/i915: Attempt to uncouple object after catastrophic failure in unbind
drm/i915: Repeat unbinding during free if interrupted (v6)
drm/i915: Refactor i915_gem_retire_requests()
drm/i915: Warn if we run out of FIFO space for a mode
drm/i915: Round up the watermark entries (v3)
drm/i915: Typo in (unused) register mask for overlay.
drm/i915: Check overlay stride errata for i830 and i845
drm/i915: Validate the mode for eDP by using fixed panel size
drm/i915: Always use the fixed panel timing for eDP
drm/i915: Enable panel fitting for eDP
drm/i915: Add fixed panel mode parsed from EDID for eDP without fixed mode in VBT
drm/i915/sdvo: Set sync polarity based on actual mode
drm/i915/hdmi: Set sync polarity based on actual mode
drm/i915/pch: Set transcoder sync polarity for DP based on actual mode
drm/i915: Initialize LVDS and eDP outputs before anything else
drm/i915/dp: Correctly report eDP in the core connector type
...
Intel variants don't support it.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Logic was:
if (mode0 && mode1)
else if (mode0)
else
Should be:
if (mode0 && mode1)
else if (mode0)
else if (mode1)
Otherwise we may end up calculating the priority regs with
unitialized values.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=16492
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
I wrote this for the prime sharing work, but I also noticed other external
non-upstream drivers from a large company carrying a similiar patch, so I
may as well ship it in master.
Signed-off-by: Dave Airlie <airlied@redhat.com>
My fine DisplayPort output was getting ST dithering forever after
having had the LVDS enabled at one point.
Signed-off-by: Eric Anholt <eric@anholt.net>
If we were not able to map the io bar in device init, don't attempt
to unmap it in device fini. All radeons should have a io bar, so
I doubt this would ever trigger, but just to be on the safe side...
Pointed out by: Alberto Milone <alberto.milone@canonical.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some BIOSes will claim a large chunk of stolen space. Unless we
reclaim it, our aperture for remapping buffer objects will be
constrained. So clamp the stolen space to 32M and ignore the rest.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=15469 among others.
Adding the ignored stolen memory back into the general pool using the
memory hotplug code is left as an exercise for the reader.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Simon Farnsworth <simon.farnsworth@onelan.com>
Tested-by: Artem S. Tashkinov <t.artem@mailcity.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The docs warn that to position the cursor such that no part of it is
visible on the pipe is an undefined operation. Avoid such circumstances
upon changing the mode, or at any other time, by unsetting the cursor if
it moves out of bounds.
"For normal high resolution display modes, the cursor must have at least a
single pixel positioned over the active screen.” (p143, p148 of the hardware
registers docs).
Fixes:
Bug 24748 - [965G] Graphics crashes when resolution is changed with KMS
enabled
https://bugs.freedesktop.org/show_bug.cgi?id=24748
v2: Only update the cursor registers if they change.
v3: Fix the unsigned comparision of x,y against width,height.
v4: Always set CUR.BASE or else the cursor may become corrupt.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-by: Christian Eggers <ceggers@gmx.de>
Cc: Christopher James Halse Rogers <chalserogers@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
When creating an object, we create the handle by which it is known to
the process and which own the reference to the object. That reference to
the new handle is what we want to transfer to the process, not the lost
reference to the object; so free the local object reference *not* the
process's handle reference.
This brings i915_gem_object_create_ioctl() into line with
drm_gem_open_ioctl()
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
If we fail to flush outstanding GPU writes but return the memory to the
system, we risk corrupting memory should the GPU recovery and complete
those writes. On the other hand, if we bail early and free the object
then we have a definite use-after-free and real memory corruption.
Choose the lesser of two evils, since in order to recover from the hung
GPU we need to completely reset it, those pending writes should
never happen.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
If during the freeing of an object the unbind is interrupted by a system
call, which is quite possible if we have outstanding GPU writes that
must be flushed, the unbind is silently aborted. This still leaves the
AGP region and backing pages allocated, and perhaps more importantly,
the object remains upon the various lists exposing us to memory
corruption.
I think this is the cause behind the use-after-free, such as
Bug 15664 - Graphics hang and kernel backtrace when starting Azureus
with Compiz enabled
https://bugzilla.kernel.org/show_bug.cgi?id=15664
v2: Daniel Vetter reminded me that kernel space programming is never easy.
We cannot simply spin to clear the pending signal and so must deferred
the freeing of the object until later.
v3: Run from the top level retire requests.
v4: Tested with P(return -ERESTARTSYS)=.5 from i915_gem_do_wait_request()
v5: Rebase against Eric's for-linus tree.
v6: Refactor, split and add a comment about avoiding unbounded recursion.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
Combine the iteration over active render rings into a common function.
This is in preparation for reusing the idle function to also retire
deferred free requests.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Even though "we have enough padding that it should be ok", round up the
watermark entries to the next unit to be on the safe side...
v2: Use the DIV_ROUND_UP macro
v3: Spotted a few more missing round-ups.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Apparently i830 and i845 cannot handle any stride that is not a multiple
of 256, unlike their brethren which do support 64 byte aligned strides.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
When trying to set other display mode besides the fixed panel mode, the
panel fitting should be enabled. This is similar to LVDS.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
This makes them sort to the front in X, which makes them likely to be
the primary outputs if you haven't specified a preference in your DE,
which is likely to be what you want.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Do this for both real eDP and for PCH_DP_D when used as the eDP
connection.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Move the common routines into separate functions to not only increase
readability, but also throwaway surplus code.
In doing so, we review the calculation of the aspect preserving scaling
and avoid the use of fixed-point until we need to calculate the accurate
scale factor.
v2: Improve comments as suggested by Jesse.
1 files changed, 105 insertions(+), 194 deletions(-)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
We already checked just a couple of lines above that we have found a
fixed_panel_mode for the LVDS, so remove the surplus check.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes https://bugs.freedesktop.org/show_bug.cgi?id=29141 though the
workaround itself is still a bit of a mystery.
Tested-by: Adam Hill <sidepipeuk@yahoo.co.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
When trying to keep track of features between the kernel, the 2D driver,
mesa and the specs, it helps to list any other name by which the device
is referred to.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
The original i965, including the revised G35 and Q35, requires an
alignment of 128K for the display surface with linear memory, so
increase the requirement from 64k for these chipsets. For the later
chipsets in the i965 family, only a 4k alignment is required. (So
long as we do not start performing asynchronous flips.)
Note the impact of this should be slight as on i965 we should be using a
tiled frontbuffer for anything up to a 4096x4096 display.
v2: compilation fixes and note that the docs do not exclude the G35 from
the extra alignment.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Unmask the bits for link training reporting before starting link
training. If stage 1 training finished before we unmask them, then we'd
spin around in a loop a few times until smashing on through. Which is
harmless, since training _did_ succeed, it just looks ugly in dmesg.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
NUM_TV_MODES is the same as ARRAY_SIZE(tv_modes). In the end, I
decided it was cleaner to remove NUM_TV_MODES and just use
ARRAY_SIZE(tv_modes) through out.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
References:
Bug 26691 - Spurious hangcheck whilst executing a long shader over a
large vertex buffer
https://bugs.freedesktop.org/show_bug.cgi?id=26691
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
We generally issue an error message at the point of failure, and so this
warning with a fairly pointless stacktrace is superfluous and ugly.
Needless to say, the common trigger for this WARN happens to be EIO
where this is pure noise.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Since mode->clock is in kHz we should be checking against 2700000
instead of just 27000. This patch gets my x201s working again (well
working as well as it ever was anyway).
When looking for this I also noticed we set link_bw to 270000, but the
calculation is different. Does it also need to use kHz or we using
10kHz internally?
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
drivers/gpu/drm/i915/intel_tv.c|479 col 16| warning: cast truncates bits
from constant value (8 becomes 0)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
drivers/gpu/drm/i915/i915_drv.c|485 col 25| warning: symbol 'i915_pm_ops' was not declared. Should it be static?
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
drivers/gpu/drm/i915/i915_drv.c|100 col 18| warning: Initializer entry defined twice
drivers/gpu/drm/i915/i915_drv.c|101 col 3| also defined here
drivers/gpu/drm/i915/i915_drv.c|117 col 18| warning: Initializer entry defined twice
drivers/gpu/drm/i915/i915_drv.c|118 col 3| also defined here
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
drivers/gpu/drm/i915/i915_drv.h|676 col 19| warning: dubious bitfield without explicit `signed' or `unsigned'
drivers/gpu/drm/i915/i915_drv.h|712 col 19| warning: dubious bitfield without explicit `signed' or `unsigned'
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Simple fix for error propagation along the old UMS path.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
checkpatch complains about this define:
WARNING: space prohibited between function name and open parenthesis '('
+#define GEN6_RENDER TIMEOUT_COUNTER_EXPIRED (1 << 6)
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
About 0.2W power can be saved on one HP laptop.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The hardware team suggest that the "large buffer" method should be
used to calculate the cursor watermark under non-SR state as well,
which is to avoid the flicker when FBC is enabled on Ironlake.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
In SR mode cursor plane watermark calculation uses same formula
like display plane. This one fixes the case for 965G and G45.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The total self-refresh fifo entry size for display plane is 512
instead of 128 for 965G. Also fix WM value mask for 965G.
About 1.0W power can be saved on one T61 laptop after the self-refresh
watermark is configured correctly.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Zhenyu wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
For self-refresh mode WM calculation's "line time" should use
mode's htotal instead of hdisplay. "surface width" is the hdisplay
for display plane and 64 for cursor plane.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This one adds support for eDP that connected on PCH DP-D port
instead of CPU DP-A port, and only DP-D port could be used for eDP.
https://bugs.freedesktop.org/show_bug.cgi?id=27220
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Tested-by: Jan-Hendrik Zab <jan@jhz.name>
Tested-by: Templar <templar@rshc.de>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Having two sets has made me think I caught a bug more than once now.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
On some machines (currently only the Toshiba Tecra A11 is known), the GPU
locks up when modeset is forced on LID open. This patch adds a new DMI
blacklist and omits modesetting for all matches.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=15550
Signed-off-by: Thomas Bächler <thomas@archlinux.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
This interface allows userspace to request hyperz support, it probably
needs more locking, and really reporting that you can have hyperz is racy
since someone else might get it before you do.
v2: modify so we pass 0 valued packets to let DDX/r300c keep working.
also fixed incorrect 0x4f1c reference.
v3: fixup zb_bw_cntl so older drivers keep working
v4: add locking, fixup SC_HYPERZ_EN - patch stream to disable hiz
Signed-off-by: Dave Airlie <airlied@redhat.com>
This migrates a bunch of DRM_DEBUG->DRM_DEBUG_KMS so we can get more modesetting related info without all the other ioctl handling easily.
Also the PM code moves to DRM_DEBUG_DRIVER mostly.
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'nouveau/for-airlied' of ../drm-nouveau-next: (77 commits)
drm/nouveau: set TASK_(UN)INTERRUPTIBLE before schedule_timeout()
drm/nv50: fix some not-error error messages
drm/nouveau: introduce gpio engine
drm/nv50: correct wait condition for instmem flush
drm/nouveau: Fix TV-out detection on unposted cards lacking a usable DCB table.
drm/nouveau: Get rid of the remaining VGA CRTC locking.
drm/nouveau: Move display init to a new nouveau_engine.
drm/nouveau: Put back the old 2-messages I2C slave test.
drm/nouveau: Reset AGP before running the init scripts.
drm/nv30: Init the PFB+0x3xx memory timing regs.
drm/nouveau: disable hotplug detect around DP link training
drm/nv50: add function to control GPIO IRQ reporting
drm/nouveau: add nv_mask register accessor
drm/nouveau: fix build without CONFIG_ACPI
drm/nouveau: Reset CRTC owner to 0 before BIOS init.
drm/nouveau: No need to lock/unlock the VGA CRTC regs all the time.
drm/nouveau: Remove useless CRTC_OWNER logging.
drm/nouveau: Add some generic I2C gadget detection code.
drm/i2c/ch7006: Don't assume that the specified config points to static memory.
drm/nv04-nv3x: Implement init-compute-mem.
...
Conflicts:
drivers/gpu/drm/nouveau/nouveau_bios.c
* 'drm-radeon-next' of ../drm-radeon-next: (333 commits)
drm/radeon/kms: trivial code style fixes for audio
drm/radeon: remove viewport transform from r6xx/r7xx blit emit
drm/radeon: group r6xx/r7xx newly sequential blit state
drm/radeon: reorder r6xx/r7xx blit state emit to make more regs sequential
drm/radeon: r6xx/r7xx move vport clipping to a single packet
drm/radeon: group r6xx/r7xx sequential blit state
drm/radeon: remove duplicate state emit in r6xx/r7xx blit
drm/radeon: add comments to r6xx/r7xx blit state
drm/radeon/kms/r7xx: add workaround for hw issue with HDP flush
drm/radeon/kms: remove rs4xx gart limit
drm: radeon: fix sign bug
drm/radeon/kms: check/restore sanity before doing anything else with GPU.
drm/radeon: fall back to GTT if bo creation/validation in VRAM fails.
drm/radeon/kms: add ioport register access
drm/radeon/kms: enable HDMI audio on RS600/RS690/RS740
drm/radeon/kms: track audio engine state, do not use not setup timer
drm/radeon/kms/r6xx+: add query for tile config (v2)
drm/radeon/kms: fix CS alignment checking for tiling (v2)
drm/radeon/kms: add tiling support to the cs checker for r6xx/r7xx
drm/radeon/kms: Add crtc tiling setup support for evergreen
...
sil164 transmitters are used for DVI outputs on Intel/nvidia and ATI setups.
So far only nouveau can use this driver.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Tested-by: Patrice Mandin <patmandin@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixed brace, macro and spacing coding style issues, and a C99 comment.
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The device name is tightly coupled and created at the same time as the
master->unique address, so we need to free it with the master. Currently
we overwrite it each time we create a new master:
unreferenced object 0xe32c54b0 (size 32):
comm "Xorg", pid 1455, jiffies 4294721798 (age 3196.879s)
hex dump (first 32 bytes):
69 39 31 35 40 70 63 69 3a 30 30 30 30 3a 30 30 i915@pci:0000:00
3a 30 32 2e 30 00 6b 6b 6b 6b 6b 6b 6b 6b 6b a5 :02.0.kkkkkkkkk.
backtrace:
[<c04e5657>] create_object+0x124/0x1f1
[<c07cf0f0>] kmemleak_alloc+0x4c/0x90
[<c04db84c>] __kmalloc+0x155/0x175
[<f8316665>] drm_setversion+0x11d/0x1b1 [drm]
[<f83148d4>] drm_ioctl+0x29a/0x356 [drm]
[<c04f27c4>] vfs_ioctl+0x33/0x91
[<c04f31cf>] do_vfs_ioctl+0x46b/0x496
[<c04f3240>] sys_ioctl+0x46/0x66
[<c040325f>] sysenter_do_call+0x12/0x38
[<ffffffff>] 0xffffffff
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
/* A typical clean-up sequence for objects stored in an idr tree, will
* use idr_for_each() to free all objects, if necessary, then
* idr_remove_all() to remove all ids, and idr_destroy() to free
* up the cached idr_layers.
*/
We were missing the vital idr_rmove_all() step and so were leaking
the used layers for every dri client:
unreferenced object 0xf32133c0 (size 148):
comm "plymouthd", pid 131, jiffies 4294678490 (age 2308.030s)
hex dump (first 32 bytes):
04 00 00 00 00 00 00 00 00 00 00 00 00 40 19 f3 .............@..
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<c04e5657>] create_object+0x124/0x1f1
[<c07cf100>] kmemleak_alloc+0x4c/0x90
[<c04db6a9>] kmem_cache_alloc+0xee/0x13c
[<c05c3d25>] idr_pre_get+0x24/0x61
[<f8315c9c>] drm_gem_handle_create+0x27/0x7f [drm]
[<f89925b2>] i915_gem_create_ioctl+0x4f/0x71 [i915]
[<f83148ac>] drm_ioctl+0x272/0x356 [drm]
[<c04f27c4>] vfs_ioctl+0x33/0x91
[<c04f31cf>] do_vfs_ioctl+0x46b/0x496
[<c04f3240>] sys_ioctl+0x46/0x66
[<c040325f>] sysenter_do_call+0x12/0x38
[<ffffffff>] 0xffffffff
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=15803
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
set_current_state() is called only once before the first iteration.
After return from schedule_timeout() current state is TASK_RUNNING. If
we are going to wait again, set_current_state() must be called.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Trivial fix to set y1 = y2 = 0.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We aren't using it, so no need. Save additional dwords.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
group state that is emitted sequentially into fewer packets.
This saves a number of dwords.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
group state that is emitted sequentially into fewer packets.
This saves a number of dwords.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Use of HDP_*_COHERENCY_FLUSH_CNTL can cause a hang in certain
situations. Add workaround.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
We used to limit the rs4xx gart aperture to 32 MB, but I suspect
that was due to not meeting the alignment requirements of the
aperture. This patch should only be applied after:
"drm/radeon/kms: fix gtt MC base alignment on rs4xx/rs690/rs740 asics"
has been applied.
This patch should probably soak for a bit in d-r-t.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The "error" variable is unsigned so it's never less than zero. I
changed it to check if (freq < current_freq) directly.
"best_error" is also unsigned so "best_error - 100" could be a large
number instead of a negative. Since "error" is unsigned it is never
less than a negative and so the cases where "best_error" is less than or
equal to 100 are false.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On systems using kexec, the new kernel is booted straight from the old kernel, without any warning to the graphics driver. So the GPU is basically left as-is in a running state, however the CPU side is completly reset.
Without stating the saneness of anyone using kexec on live systems, we should at least try not to crash the GPU. This patch resets 3 registers to 0 that could cause bad things to happen to the running system.
This allows kexec to work on a Power6/RN50 system.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This fixes a problem where on low VRAM cards we'd run out of space for validation.
[airlied: Tested on my M7, Thinkpad T42, compiz works with no problems.]
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is required for the NB_MISC regs on rs780/rs880 which
means HDMI/DVI/DP ports using PCIEPHY won't work without
it. It might also help with s/r (asic init) issues on other
atombios cards.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=28774
and similar issues reported by Alberto Milone.
[airlied: Squash io fix patch]
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Tested-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We will need method of selecting encoder that should receive HDMI block. For
now we assign HDMI block to first enabled encoder. Hopefully there are not many
RS6x0 chips with two digital encoders.
[airlied: add RS740 checks as per Alex suggestion.]
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is needed to enable audio support on devices using polling. In case user
decides to disable audio (module parameter) we still will try to use timer in
r600_audio_enable_polling. This would lead to BUG in kernel/timer.c.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Userspace needs this information to access tiled
buffers via the CPU.
v2: rebased on evergreen accel changes
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Check for relocs for DB_DEPTH_INFO, CB_COLOR*_INFO, and texture
resources.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
rv6xx/rv7xx/evergreen families supported; older asics did
not have an internal thermal sensor.
Note, not all oems use the internal thermal sensor, so it's
only exposed in cases where it is used.
Note also, that most laptops use an oem specific ACPI solution for
GPU thermal information rather than using the internal thermal
sensor directly.
v2: export millidegrees celsius, use hwmon device properly.
v3: fix Kconfig
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
By calling the ATIF method in the radeon driver we can make sure
that hotkeys such as the video switch key emit ACPI events when
pressed.
agd5f: fix warning
Signed-off-by: Alberto Milone <alberto.milone@canonical.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some tables have delays that can cause the timeout to hit
even when not intended.
Should fix:
https://bugs.freedesktop.org/show_bug.cgi?id=27744
and related bugs.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- Make the logic in r100_pll_errata_after_index() match the other
errata functions
- Use rdev->family rather than rdev->flags & RADEON_FAMILY_MASK for kms
- replace rn50 check using ids with ASIC_IS_RN50 convenience macro
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We're adjusting horizontal timings only here, moving vsync was just a
slavish translation of a typo in the X server.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix incorrectly reporting 'default' power profile, when it is set to 'mid'.
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix error from the last pull request. Making sure we shut the panel off
is more correct and saves power.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: add pipe A force quirks to i915 driver
drm/i915: Fix panel fitting regression since 734b4157
drm/i915: fix deadlock in fb teardown
drm/i915: don't free non-existent compressed llb on ILK+
agp/intel: Use the correct mask to detect i830 aperture size.
drm/i915: disable FBC when more than one pipe is active
drm/i915: Use the correct scanout alignment for fbcon.
drm/i915: make sure eDP panel is turned on
drm/i915: add PANEL_UNLOCK_REGS definition
drm/i915: Make G4X-style PLL search more permissive
drm/i915: Clear any existing dither mode prior to enabling spatial dithering
drm/i915: handle shared framebuffers when flipping
drm/i915: Explosion following OOM in do_execbuffer.
gpu/drm/i915: Add a blacklist to omit modeset on LID open
Ported over from the old UMS list. Unfortunately they're still
necessary especially on older laptop platforms.
Fixes https://bugs.freedesktop.org/show_bug.cgi?id=22126.
Tested-by: Xavier <shiningxc@gmail.com>
Tested-by: Diego Escalante Urrelo <diegoe@gnome.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
The crtc mode fixup is run after the encoders adjust the mode to fit on
their output, so don't reset the mode!
Fixes:
Bug 29057 - display corruption under 800x600 on netbook
(1024x600) with 'Full Aspect' scaling
https://bugs.freedesktop.org/show_bug.cgi?id=29057
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Xun Fang <xunx.fang@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
At module unload time we'll tear down the fbdev state. We do so under
the struct mutex, so we shouldn't try to use the unlocked variant of
the GEM object unreference function or we may deadlock.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
We should only free the compressed llb if we allocated it in the first
place otherwise we'll panic at unload time.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
We're really supposed to do this to avoid trouble with underflows when
multiple planes are active.
Fixes https://bugs.freedesktop.org/show_bug.cgi?id=26987.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: fangxun <xunx.fang@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This fixes a potential modesetting error during boot with plymouth on
Broadwater and Crestline introduced with 9df47c. The framebuffer was
hard-coding an alignment of 64K, but the modesetting code required the
documented alignment of 128K. The result was that we would attempt to
unbind the pinned fbcon buffer, triggering an ERROR and ultimately
failing the mode change.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
When enabling the eDP port, we need to make sure the panel is turned on
after training the link. If we don't, it likely won't come back after
suspend or may not come up at all.
For unknown reasons, unlocking the panel regs before initiating a power
on sequence is necessary. There are known bugs in the PCH panel
sequencing logic, apparently this is one possible workaround.
Fixes https://bugs.freedesktop.org/show_bug.cgi?id=28739.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: "Paulo J. S. Silva" <pjssilva@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
In some cases, unlocking the panel regs is safe and can help us avoid a
flickery, full mode set sequence. So define the unlock key and use it.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes an Ironlake laptop with a 68.940MHz 1280x800 panel and 120MHz SSC
reference clock.
More generally, the 0.488% tolerance used before is just too tight to
reliably find a PLL setting. I extracted the search algorithm and
modified it to find the dot clocks with maximum error over the valid
range for the given output type:
http://people.freedesktop.org/~ajax/intel_g4x_find_best_pll.c
This gave:
Worst dotclock for Ironlake DAC refclk is 350000kHz (error 0.00571)
Worst dotclock for Ironlake SL-LVDS refclk is 102321kHz (error 0.00524)
Worst dotclock for Ironlake DL-LVDS refclk is 219642kHz (error 0.00488)
Worst dotclock for Ironlake SL-LVDS SSC refclk is 84374kHz (error 0.00529)
Worst dotclock for Ironlake DL-LVDS SSC refclk is 183035kHz (error 0.00488)
Worst dotclock for G4X SDVO refclk is 267600kHz (error 0.00448)
Worst dotclock for G4X HDMI refclk is 334400kHz (error 0.00478)
Worst dotclock for G4X SL-LVDS refclk is 95571kHz (error 0.00449)
Worst dotclock for G4X DL-LVDS refclk is 224000kHz (error 0.00510)
Signed-off-by: Adam Jackson <ajax@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
We cannot the initial configuration set by the BIOS not to have a dither
mode enabled which conflicts with our enabling the Spatial Temporal 1
dither mode for PCH. In particular, the BIOS may either enable temporal
dithering or the Spatial Temporal 2 with the result that we enable pure
temporal dithering. Temporal dithering looks bad and is perceived as a
flicker.
Fixes:
Bug 29248 - [Arrandale] Annoying flicker on internal panel, goes away
after suspend to RAM
https://bugs.freedesktop.org/show_bug.cgi?id=29248
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
If a framebuffer is shared across CRTCs, the x,y position of one of them
is likely to be something other than the origin (e.g. for extended
desktop configs). So calculate the offset at flip time so such
configurations can work.
Fixes https://bugs.freedesktop.org/show_bug.cgi?id=28518.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Thomas M. <tmezzadra@gmail.com>
Tested-by: fangxun <xunx.fang@intel.com>
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
I was hoping we could detect I2C devices at a given address without
actually writing data into them, but apparently some DDC slaves get
confused with 0-bytes transactions. Put the good old test back.
Reported-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
BIOS scripts usually make an attempt to reset the AGP controller,
however on some nv4x cards doing it properly involves switching FW off
and on: if we do that without updating the AGP bridge settings
accordingly (e.g. with the corresponding calls to agp_enable()) we
will be locking ourselves out of the card MMIO space. Do it from
nouveau_mem_reset_agp() before the init scripts are executed.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Fixes the randomly flashing vertical lines seen on some nv3x after a
cold-boot.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Fixes suspend+multihead on some boards that also use BIOS scripts for
modesetting.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Locking only makes sense in the VBIOS parsing code as it's executed
before CRTC init.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Clean up and move the external TV encoder detection code to
nouveau_i2c.c, it's also going to be useful for external TMDS and DDC
detection.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Init-compute-mem was the last piece missing for nv0x-nv3x card
cold-booting. This implementation is somewhat lacking but it's been
reported to work on most chipsets it was tested in. Let me know if it
breaks suspend to RAM for you.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Tested-by: Patrice Mandin <patmandin@gmail.com>
Tested-by: Ben Skeggs <bskeggs@redhat.com>
Tested-by: Xavier Chantry <chantry.xavier@gmail.com>
Tested-by: Marcin Kościelnicki <koriakin@0x04.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Also collect all the PFB registers in a single place and remove some
duplicated definitions.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Rescaling interlaced modes isn't going to work correctly, and even if
it did, come on, interlaced flat panels? are you pulling my leg?
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
A previous commit started additionally using the SOR link when trying to
match the correct output script. However, we never fill in this field
for LVDS so we can never match a script at all.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
There's a report of this quirk breaking modesetting on at least one board.
After discussion with Francisco Jerez, we've decided to remove it:
<darktama> it's not worth limiting the quirk to just where we know it can
work? i'm happy either way really :)
<curro> hmm, don't think so, most if not all DCB15 cards have just one DAC
<curro> and with that quirk there's no way to tell if the load comes from
the VGA or DVI port
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Acked-by: Francisco Jerez <currojerez@riseup.net>
Workqueue can now handle high concurrency. Convert drm_crtc_helper to
use system_nrt_wq instead of slow-work. The conversion is mostly
straight forward. One difference is that drm_helper_hpd_irq_event()
no longer blocks and can be called from any context.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: add quirk to make HP DV5000 laptop resume
drm/radeon/kms: fix RADEON_INFO_CRTC_FROM_ID info ioctl
Fix ttm_page_alloc.c build breakage
drm/radeon/kms: fix legacy LVDS dpms sequence
drm/radeon/kms: drop taking lock around crtc lookup.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=29062
Reported-by: Andres Cimmarusti <acimmarusti@gmail.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Return the crtc_id, not the counter value. They are not
necessarily the same.
Cc: Jerome Glisse <glisse@freedesktop.org>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The commit 1e8655f873
drm/ttm: Fix build on architectures without AGP
looks at TTM_HAS_AGP before it has been set in ttm_bo_driver.h
Move the conditional inclusion of <asm/agp.h> *after* we have included
ttm_bo_driver.h
Signed-of-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add delay after turning off the LVDS encoder.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=16389
Tested-by: Jan Kreuzer <kontrollator@gmx.de>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
We only add/remove crtcs at driver load, you cannot remove when
the GPU is running a CS packet since the fd is open, when
GPU hotplugging on radeons actually is needed all this locking
needs a review and I've started re-working kms core locking to deal
with this better. But for now avoid long delays in CS processing when
hotplug detect is happening in a different thread.
this fixes a regression introduced with hotplug detection.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add the shrinkers missed in the first conversion of the API in
commit 7f8275d0d6 ("mm: add context argument to
shrinker callback").
Signed-off-by: Dave Chinner <dchinner@redhat.com>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/r600: fix possible NULL pointer derefernce
drm/radeon/kms: add quirk for ASUS HD 3600 board
include/linux/vgaarb.h: add missing part of include guard
drm/nouveau: Fix crashes during fbcon init on single head cards.
drm/nouveau: fix pcirom vbios shadow breakage from acpi rom patch
drm/radeon/kms: fix shared ddc harder
drm/i915: enable low power render writes on GEN3 hardware.
drm/i915: Define MI_ARB_STATE bits
vmwgfx: return -EFAULT if copy_to_user fails
fb: handle allocation failure in alloc_apertures()
drm: radeon: check kzalloc() result
drm/ttm: Fix build on architectures without AGP
drm/radeon/kms: fix gtt MC base alignment on rs4xx/rs690/rs740 asics
drm/radeon/kms: fix possible mis-detection of sideport on rs690/rs740
drm/radeon/kms: fix legacy tv-out pal mode
Disables the crts as per dpms and also disables the ppll
associated with the crtc. This should save additional power.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There's no convenient/reliable way for drivers to both obey the dithering
mode property, and to be able to attempt to provide a good default in all
cases.
This commit adds an "auto" method to the property which drivers can default
to if they wish, whilst still allowing the user to override the choice as
they do now.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reported-by: Alexander Y. Fomichev <git.user@gmail.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Connector is actually DVI rather than HDMI.
Reported-by: trapDoor <trapdoor6@gmail.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
this fixes a regression since the fbcon rework.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On nv50 it became impossible to attempt a PCI ROM shadow of the VBIOS,
which will break some setups.
This patch also removes the different ordering of shadow methods for
pre-nv50 chipsets. The reason for the different ordering was paranoia,
but it should hopefully be OK to try shadowing PRAMIN first.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This fixes a regression caused by b2ea4aa67b
due to the way shared ddc with multiple digital connectors was handled.
You generally have two cases where DDC lines are shared:
- HDMI + VGA
- HDMI + DVI-D
HDMI + VGA is easy to deal with because you can check the EDID for the
to see if the attached monitor is digital. A shared DDC line with two
digital connectors is more complex. You can't use the hdmi bits in the
EDID since they may not be there with DVI<->HDMI adapters. In this case
all we can do is check the HPD pins to see which is connected as we have
no way of knowing using the EDID.
Reported-by: trapdoor6@gmail.com
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
A lot of 945GMs have had stability issues for a long time, this manifested as X hangs, blitter engine hangs, and lots of crashes.
one such report is at:
https://bugs.freedesktop.org/show_bug.cgi?id=20560
along with numerous distro bugzillas.
This only took a week of digging and hair ripping to figure out.
Tracked down and tested on a 945GM Lenovo T60,
previously running
x11perf -copypixwin500
or
x11perf -copywinpix500
repeatedly would cause the GPU to wedge within 4 or 5 tries, with random busy bits set.
After this patch no hangs were observed.
cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
The i915 memory arbiter has a register full of configuration
bits which are currently not defined in the driver header file.
Signed-off-by: Keith Packard <keithp@keithp.com>
cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
copy_to_user() returns the number of bytes remaining to be copied, but
we want to return a negative error code. This gets copied to user
space.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Make inclusion of <asm/agp.h> conditional on TTM_HAS_AGP. The use
of the functions declared in it is already conditional.
Reported-by: Geert Stappers <stappers@stappers.nl>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Tested-by: Geert Stappers <stappers@stappers.nl>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The current shrinker implementation requires the registered callback
to have global state to work from. This makes it difficult to shrink
caches that are not global (e.g. per-filesystem caches). Pass the shrinker
structure to the callback so that users can embed the shrinker structure
in the context the shrinker needs to operate on and get back to it in the
callback via container_of().
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The hibernate issues that got fixed in commit 985b823b91 ("drm/i915:
fix hibernation since i915 self-reclaim fixes") turn out to have been
incomplete. Vefa Bicakci tested lots of hibernate cycles, and without
the __GFP_RECLAIMABLE flag the system eventually fails to resume.
With the flag added, Vefa can apparently hibernate forever (or until he
gets bored running his automated scripts, whichever comes first).
The reclaimable flag was there originally, and was one of the flags that
were dropped (unintentionally) by commit 4bdadb9785 ("drm/i915:
Selectively enable self-reclaim") that introduced all these problems,
but I didn't want to just blindly add back all the flags in commit
985b823b91, and it looked like __GFP_RECLAIM wasn't necessary. It
clearly was.
I still suspect that there is some subtle reason we're missing that
causes the problems, but __GFP_RECLAIMABLE is certainly not wrong to use
in this context, and is what the code historically used. And we have no
idea what the causes the corruption without it.
Reported-and-tested-by: M. Vefa Bicakci <bicave@superonline.com>
Cc: Dave Airlie <airlied@gmail.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The asics in question have the following requirements with regard to
their gart setups:
1. The GART aperture size has to be in the form of 2^X bytes, where X is from 25 to 31
2. The GART aperture MC base has to be aligned to a boundary equal to the size of the
aperture.
3. The GART page table has to be aligned to the boundary equal to the size of the table.
4. The GART page table size is: table_entry_size * (aperture_size / page_size)
5. The GART page table has to be allocated in non-paged, non-cached, contiguous system
memory.
This patch takes care 2. The rest should already be handled properly.
This fixes a regression noticed by: Torsten Kaiser <just.for.lkml@googlemail.com>
Tested-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Unify debug printing so it easier to track what's happening
while debugging.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Check ulBootUpMemoryClock on AMD IGPs.
Fix regression noticed by Torsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
On nv50 it became impossible to attempt a PCI ROM shadow of the VBIOS,
which will break some setups.
This patch also removes the different ordering of shadow methods for
pre-nv50 chipsets. The reason for the different ordering was paranoia,
but it should hopefully be OK to try shadowing PRAMIN first.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
On older cards (<nv17) scanout gets blocked when the ROM is being
accessed. PROM access usually comes out enabled from suspend, switch
it off.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
In some situations it's possible we can receive a spurious hotplug IRQ
before we're ready to handle it, leading to an oops.
Calling the display init before enabling interrupts should clear any
pending IRQs on the GPU and prevent this from happening.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
It seems on some chipsets that doing this from the 0x20 handler causes the
display engine to not ever signal the final 0x40 stage.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This removes the previous prepare_access() and finish_access() hooks, and
replaces it with a much simpler flush() hook.
All the chipset-specific code before nv50 has its use removed completely,
as it's not required there at all.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The previous handler basically worked correctly for a full-blown mode
change. However, it did nothing at all when a partial (encoder only)
reconfiguation was necessary, leading to the display hanging on certain
types of mode switch.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
It turns out that the display engine signals an interrupt for disconnects
too. In order to make it easier to process the display interrupts
correctly, we want to ensure we only get one operation per interrupt
sequence - this is what this commit achieves.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The blob seems to have the same problem so it's probably a hardware
issue (bug 28810).
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Avoids an oops in the fence wait failure path (bug 26521).
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Tested-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
No need to spam the logs when they're found, they're equivalent to
INIT_DONE.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Load detection needs the connector wired to a CRTC, when there are no
inactive CRTCs left that means we need to cut some other head off for
a while, causing intermittent flickering.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Allows us to remove a driver hack that used to be necessary to disable
encoders in certain situations before setting up a mode. The DRM has
better knowledge of when this is needed than the driver does.
This fixes a number of display switching issues.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Uncertain if this is a weirdo configuration, or a BIOS bug. If it's not
a BIOS bug, we still don't know how to make it work anyway so ignore a
"conflicting" DCB entry to prevent a display hang.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
As long as we know the length of the opcode, we're probably better off
trying to parse the remainder of an init table rather than aborting in
the middle of it.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Create connectors before encoders to avoid having to do another loop across
encoder list whenever we create a new connector. This allows us to pass
the connector to the encoder creation functions, and avoid using a
create_resources() callback since we can now call it directly.
This can also potentially modify the connector ordering on nv50. On cards
where the DCB connector and encoder tables are in the same order, things
will be unchanged. However, there's some cards where the ordering between
the tables differ, and in one case, leads us to naming the connectors
"wrongly".
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
fixes oops in nouveau_connector_get_modes with nv_encoder is NULL
Signed-off-by: Albert Damen <albrt@gmx.net>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The nv05 card in the bug report [1] doesn't have usable I2C port
register offsets (they're all filled with zeros). Ignore them and use
the defaults.
[1] http://bugs.launchpad.net/bugs/569505
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We just need to clear the SBA and ENABLE bits to reset the AGP
controller: If the AGP bridge was configured to use "fast writes",
clearing the FW bit would break the subsequent MMIO writes and
eventually end with a lockup.
Note that all the BIOSes I've seen do the same as we did (it works for
them because they don't use MMIO), OTOH the blob leaves FW untouched.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
a7b9f9e5adef dropped it by accident.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Tested-by: Thibaut Girka <thib@sitedethib.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Luckily this had absolutely no effect whatsoever :)
Reported-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
