Most other mainstream terminals support "xterm256" colours, which means
people sometimes use these blindly without checking capabilities.
Because of hardware limitations of VGA consoles, colours are downgraded to
16 foregrounds and 8 backgrounds. On fbdev consoles it would be possible
to support them without quality loss, but adding that would require quite a
large amount of code.
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 5f5c9ae56c
"serial_core: Unregister console in uart_remove_one_port()"
fixed a crash where a serial port was removed but
not deregistered as a console.
There is a side effect of that commit for platforms having serial consoles
and of_serial configured (CONFIG_SERIAL_OF_PLATFORM). The serial console
is disabled midway through the boot process.
This cessation of the serial console affects PowerPC computers
such as the MVME5100 and SAM440EP.
The sequence is:
bootconsole [udbg0] enabled
....
serial8250/16550 driver initialises and registers its UARTS,
one of these is the serial console.
console [ttyS0] enabled
....
of_serial probes "platform" devices, registering them as it goes.
One of these is the serial console.
console [ttyS0] disabled.
The disabling of the serial console is due to:
a. unregister_console in printk not clearing the
CONS_ENABLED bit in the console flags,
even though it has announced that the console is disabled; and
b. of_platform_serial_probe in of_serial not setting the port type
before it registers with serial8250_register_8250_port.
This patch ensures that the serial console is re-enabled when of_serial
registers a serial port that corresponds to the designated console.
Signed-off-by: Stephen Chivers <schivers@csc.com>
Tested-by: Stephen Chivers <schivers@csc.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [unregister_console]
Cc: stable <stable@vger.kernel.org> # 3.15
===
The above failure was identified in Linux-3.15-rc2.
Tested using MVME5100 and SAM440EP PowerPC computers with
kernels built from Linux-3.15-rc5 and tty-next.
The continued operation of the serial console is vital for computers
such as the MVME5100 as that Single Board Computer does not
have any grapical/display hardware.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using dma_mapping_error() to make sure the mapping did not
fail.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250 uart driver currently supports only software assisted hw flow
control. The software assisted hw flow control maintains a hw_stopped
flag in the tty structure to stop and start transmission and use modem
status interrupt for the event to drive the handshake signals. This is
not needed if hw has flow control capabilities. This patch adds a
DT attribute for enabling hw flow control for a uart port. Also skip
stop and start if this flag is present in flag field of the port
structure.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
CC: Rob Herring <robh+dt@kernel.org>
CC: Pawel Moll <pawel.moll@arm.com>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Ian Campbell <ijc+devicetree@hellion.org.uk>
CC: Kumar Gala <galak@codeaurora.org>
CC: Randy Dunlap <rdunlap@infradead.org>
CC: Jiri Slaby <jslaby@suse.cz>
CC: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On sam9x5, dedicated CTS (and RTS) pins are unusable together with the
LCDC, the EMAC, or the MMC because they share the same line.
Moreover, the USART controller doesn't handle DTR/DSR/DCD/RI signals,
so we have to control them via GPIO.
This patch permits to use GPIOs to control the CTS/RTS/DTR/DSR/DCD/RI
signals.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch add some helpers to control modem lines (CTS/RTS/DSR...) via
GPIO.
This will be useful for many boards which have a serial controller that
only handle CTS/RTS pins (or even just RX/TX).
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch add IGNPAR flag handling for the driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sccnxp_timer() is triggered only by timer, so there are no need to
check for timer_pending().
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch disables the receiver ready interrupt for imx_stop_rx.
It reduces the interrupt numbers when the uart is going to close
or suspend.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DMA wait queue makes the code very complicated:
For RX, the @->stop_rx hook does not really stop the RX;
For TX, the @->stop_tx hook does not really stop the TX.
The above make the imx_shutdown has to wait the RX/TX DMA to be finished.
In order to make code more simple, this patch removes the DMA wait queue.
By calling the dmaengine_terminate_all, this patch makes the RX stops
immediately after we call the @->stop_rx hook, so does the TX.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the imx_startup(), we will reset the uart port which will reset all
the FIFOs, including the URXD.
So the code to clear the RX FIFO is redundant. Just remove it.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current code resets the uart port only when it supports the irda mode.
In actually, we also need to reset the uart port in the non-irda mode.
A hang was caught in the following case:
UART A transmits data to the other end. But the transmission maybe
terminated. In some corner case, the TX FIFO maybe not empty.
The kernel will hang at the imx_set_termios():
............................................................
while (!(readl(sport->port.membase + USR2) & USR2_TXDC))
barrier();
............................................................
This patch resets the uart port all the time in the imx_startup().
And fix the hang.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bit 7 of UCR3 is described in the i.MX reference manuals (with the exception
of i.MX1) as follows:
ADNIMP: Autobaud Detection Not Improved-. Disables new features of
autobaud detection (See Baud Rate Automatic Detection
Protocol, for more details).
0 Autobaud detection new features selected
1 Keep old autobaud detection mechanism
The "new features" mechanism occasionally cause the receiver to get out of sync
and continuously produce received characters of '\xff'.
In order to reproduce the problem:
$ stty -F /dev/ttymxc0 19200
- Change the terminal baudrate to 19200
- Type in the console and it should look good
- Change the terminal baudrate back to 115200
- Type 'b' in the console, then a stream of garbage characters is seen.
Also rename the bit definition as per the reference manual.
Tested on mx6q, mx6dl, mx6solo and mx53.
Based on a patch from Eric Nelson for U-boot.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This Multi-IO card has one serial 16550-like and one parallel port connector.
Here's the lspci output, after this commit is applied:
03:07.0 Serial controller: Device 4348:5053 (rev 10) (prog-if 02 [16550])
Subsystem: Device 4348:5053
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at cf00 [size=8]
Region 1: I/O ports at ce00 [size=8]
Kernel driver in use: parport_serial
Kernel modules: 8250_pci, parport_serial
This commit adds an entry with the device ID to the blacklist declared in
8250_pci to prevent the driver from taking ownership. Also, and as was done
for the 2S/1P variant, add a quirk to skip autodetection and set the correct
type to 16550A clone.
Proper entries are added to parport_serial, to support the device parallel
and serial ports.
Cc: Gianluca Anzolin <gianluca@sottospazio.it>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add missing specification of efm32_uart_exit as module_exit.
This fixes the following compilation warning:
drivers/tty/serial/efm32-uart.c:840:123: warning: ‘efm32_uart_exit’ defined but not used [-Wunused-function]
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Jiri Slaby <jslaby@suse.cz>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add format and argument checking and fix misuses in the dbg macro.
Add __printf
Use %pR for resource
Add #include guard to samsung.h
Move static functions from .h to .c
Use vscnprintf instead of length unguarded vsprintf
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't activate the TX Space available IRQ on startup, or a simple
$ cat /dev/ttyHSU0
will cause an endless amount of IRQs, as there is always space in
the TX FIFO available if no data is going to be sent.
Also correct comments for IRQ names (RX and TX swapped).
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@men.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On my test platform (B2020/STiH416) the serial port issues bad characters
during the initial message avalanche as the console comes up. The problem
also occurs when dense(ish) I/O is done using the polled I/O interface.
The problem is fixed for me by using the FIFO half-empty bit rather than
FIFO full bit. Note that using the half-empty bit causes the FIFO to be
managed in a similar way to interrupt based I/O (i.e. where the hardware
gets best test coverage).
Running the FIFO half full will have no impact (good or bad) on console
performance. The UART will still remain fully saturated and the busy-wait
until the FIFO is empty in asc_console_write() will complete at the same
time.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Xilinx MDM (Microblaze Debug Module) also contains
uart interface via JTAG which is compatible with
uartlite driver. This interface is really slow
that's why timeout is setup to 1s.
Make this time delay not to be cpu speed dependent.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If NO_DMA=y:
drivers/built-in.o: In function `lpuart_dma_rx_free':
fsl_lpuart.c:(.text+0x7da28): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `lpuart_dma_tx_free':
fsl_lpuart.c:(.text+0x7da60): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `lpuart_dma_rx':
fsl_lpuart.c:(.text+0x7dab8): undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `lpuart_dma_tx':
fsl_lpuart.c:(.text+0x7db7e): undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `lpuart_copy_rx_to_tty':
fsl_lpuart.c:(.text+0x7dcd4): undefined reference to `dma_sync_single_for_cpu'
make[3]: *** [vmlinux] Error 1
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb78b81142 provide a workaround for
kernel panic, but bring potential deadlock risk. that is in
sirfsoc_rx_tmo_process_tl while enter into sirfsoc_uart_pio_rx_chars
cpu hold uart_port->lock, if uart interrupt comes cpu enter into
sirfsoc_uart_isr and deadlock occurs in getting uart_port->lock.
the patch replace spin_lock version to spin_lock_irq* version to avoid
spinlock dead lock issue. let function tty_flip_buffer_push in tasklet
outof spin_lock_irq* protect area to avoid add the pair of spin_lock and
spin_unlock for tty_flip_buffer_push.
BTW drop self defined unused spinlock protect of tx_lock/rx_lock.
56274.220464] BUG: spinlock lockup suspected on CPU#0, swapper/0/0
[56274.223648] lock: 0xc05d9db0, .magic: dead4ead, .owner: swapper/0/0,
.owner_cpu: 0
[56274.231278] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G
O 3.10.35 #1
[56274.238241] [<c0015530>] (unwind_backtrace+0x0/0xf4) from
[<c00120d8>] (show_stack+0x10/0x14)
[56274.246742] [<c00120d8>] (show_stack+0x10/0x14) from
[<c01b11b0>] (do_raw_spin_lock+0x110/0x184)
[56274.255501] [<c01b11b0>] (do_raw_spin_lock+0x110/0x184) from
[<c02124c8>] (sirfsoc_uart_isr+0x20/0x42c)
[56274.264874] [<c02124c8>] (sirfsoc_uart_isr+0x20/0x42c) from
[<c0075790>] (handle_irq_event_percpu+0x54/0x17c)
[56274.274758] [<c0075790>] (handle_irq_event_percpu+0x54/0x17c)
from [<c00758f4>] (handle_irq_event+0x3c/0x5c)
[56274.284561] [<c00758f4>] (handle_irq_event+0x3c/0x5c) from
[<c0077fa0>] (handle_level_irq+0x98/0xfc)
[56274.293670] [<c0077fa0>] (handle_level_irq+0x98/0xfc) from
[<c0074f44>] (generic_handle_irq+0x2c/0x3c)
[56274.302952] [<c0074f44>] (generic_handle_irq+0x2c/0x3c) from
[<c000ef80>] (handle_IRQ+0x40/0x90)
[56274.311706] [<c000ef80>] (handle_IRQ+0x40/0x90) from
[<c000dc80>] (__irq_svc+0x40/0x70)
[56274.319697] [<c000dc80>] (__irq_svc+0x40/0x70) from
[<c038113c>] (_raw_spin_unlock_irqrestore+0x10/0x48)
[56274.329158] [<c038113c>]
(_raw_spin_unlock_irqrestore+0x10/0x48) from [<c0200034>]
(tty_port_tty_get+0x58/0x90)
[56274.339213] [<c0200034>] (tty_port_tty_get+0x58/0x90) from
[<c0212008>] (sirfsoc_uart_pio_rx_chars+0x1c/0xc8)
[56274.349097] [<c0212008>]
(sirfsoc_uart_pio_rx_chars+0x1c/0xc8) from [<c0212ef8>]
(sirfsoc_rx_tmo_process_tl+0xe4/0x1fc)
[56274.359853] [<c0212ef8>]
(sirfsoc_rx_tmo_process_tl+0xe4/0x1fc) from [<c0027c04>]
(tasklet_action+0x84/0x114)
[56274.369739] [<c0027c04>] (tasklet_action+0x84/0x114) from
[<c0027db4>] (__do_softirq+0x120/0x200)
[56274.378585] [<c0027db4>] (__do_softirq+0x120/0x200) from
[<c0027f44>] (do_softirq+0x54/0x5c)
[56274.386998] [<c0027f44>] (do_softirq+0x54/0x5c) from
[<c00281ec>] (irq_exit+0x9c/0xd0)
[56274.394899] [<c00281ec>] (irq_exit+0x9c/0xd0) from
[<c000ef84>] (handle_IRQ+0x44/0x90)
[56274.402790] [<c000ef84>] (handle_IRQ+0x44/0x90) from
[<c000dc80>] (__irq_svc+0x40/0x70)
[56274.410774] [<c000dc80>] (__irq_svc+0x40/0x70) from
[<c0288af4>] (cpuidle_enter_state+0x50/0xe0)
[56274.419532] [<c0288af4>] (cpuidle_enter_state+0x50/0xe0) from
[<c0288c34>] (cpuidle_idle_call+0xb0/0x148)
[56274.429080] [<c0288c34>] (cpuidle_idle_call+0xb0/0x148) from
[<c000f3ac>] (arch_cpu_idle+0x8/0x38)
[56274.438016] [<c000f3ac>] (arch_cpu_idle+0x8/0x38) from
[<c0059344>] (cpu_startup_entry+0xfc/0x140)
[56274.446956] [<c0059344>] (cpu_startup_entry+0xfc/0x140) from
[<c04a3a54>] (start_kernel+0x2d8/0x2e4)
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All SiRFSoC UART registers are in 32-bits. If we use writeb for
TXFIFO, actually all of 32-bits are still written, for TXTIFO,
only low 8-bits are valid, so in prima2&atlas6, this causes no
problem.
But in the new atlas7, using writeb to write UART registers will
cause an imprecise data abort as HW does check the "wrong" writeb.
So move to writel and this also makes the code consistent with
sirfsoc_uart_pio_tx_chars() in which we use writel.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two new drivers have been added since 3.14, the MEN 16z135 uart, and
the ARM semihosting console. Both are missing an explicit 'select
SERIAL_CORE', which can leads build errors when no other driver
selects the core, as found during ARM randconfig testing.
In case of the ARM semihosting console, we also have to select
SERIAL_CORE_CONSOLE.
This adds the missing 'select' statements.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes the warnings:
drivers/tty/serial/sc16is7xx.c: In function 'sc16is7xx_handle_rx':
>> drivers/tty/serial/sc16is7xx.c:548:1: warning: 'sc16is7xx_handle_rx' uses dynamic stack allocation [enabled by default]
drivers/tty/serial/sc16is7xx.c: In function 'sc16is7xx_handle_tx':
>> drivers/tty/serial/sc16is7xx.c:589:1: warning: 'sc16is7xx_handle_tx' uses dynamic stack allocation [enabled by default]
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/tty/serial/sc16is7xx.c:1060:12: warning: 'sc16is7xx_probe' defined but not used [-Wunused-function]
static int sc16is7xx_probe(struct device *dev,
^
drivers/tty/serial/sc16is7xx.c:1176:12: warning: 'sc16is7xx_remove' defined but not used [-Wunused-function]
static int sc16is7xx_remove(struct device *dev)
^
drivers/tty/serial/sc16is7xx.c:1215:29: warning: 'regcfg' defined but not used [-Wunused-variable]
static struct regmap_config regcfg = {
^
Fixed these warnings by removing the `#ifdef CONFIG_REGMAP_I2C' around their
calls as this driver selects REGMAP_I2C in Kconfig. This part of driver just
didn't compile at all when REGMAP_I2C configured as module (CONFIG_REGMAP_I2C
is not defined, just CONFIG_REGMAP_I2C_MODULE).
Signed-off-by: Jan Moskyto Matejka <mq@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On initialization failure, an error message is already printed with
level KERN_ERR, no need to print another one with level KERN_INFO.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pch_uart driver is for a companion chip to the Intel Atom E600
series processors. These are 32-bit x86 processors so the driver is
only needed on X86_32. Add COMPILE_TEST as an alternative, so that the
driver can still be build-tested elsewhere.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This function is largely a duplicate of paste_selection() in
drivers/tty/vt/selection.c, but with its own selection state. The
speakup selection mechanism should really be merged with vt.
For now, apply the changes from 'TTY: vt, fix paste_selection ldisc
handling', 'tty: Make ldisc input flow control concurrency-friendly',
and 'tty: Fix unsafe vt paste_selection()'.
References: https://bugs.debian.org/735202
References: https://bugs.debian.org/744015
Reported-by: Paul Gevers <elbrus@debian.org>
Reported-and-tested-by: Jarek Czekalski <jarekczek@poczta.onet.pl>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: <stable@vger.kernel.org> # v3.8 but needs backporting for < 3.12
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This resolves the conflicts in the files:
drivers/iio/adc/Kconfig
drivers/staging/rtl8723au/os_dep/usb_ops_linux.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable DT based earlycon initialization for the pl011 uart.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Acked-by: Grant Likely <grant.likely@linaro.org>
This adds the infrastructure to generic earlycon for earlycon setup
using DT. The actual setup is not enabled until a following commit to
add the FDT parsing.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Grant Likely <grant.likely@linaro.org>
No functional change. Just convert to the new interface.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Grant Likely <grant.likely@linaro.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Link: http://lkml.kernel.org/r/20140507154337.873477334@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
No functional change. Just convert to the new interface.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Grant Likely <grant.likely@linaro.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Link: http://lkml.kernel.org/r/20140507154337.643399187@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Mostly spacing changes, also making the operations structure const
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 9aac588759 (tty/serial: add generic serial earlycon) moved
console option parsing from 8250_early.c and converted to kstrto*
functions from simple_strtoul along the way. However, kstrto* functions
are not equivalent in that they do not allow non-convertible characters
at the end such as "115200n8". Fix this by changing back to
simple_strtoul and ignore what checkpatch.pl says.
Reported-by: Yinghai Lu <yinghai@kernel.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d2fd6810a8 (tty/serial: convert 8250 to generic earlycon)
removed setup_early_serial8250_console, but there are still 2 callers
in:
arch/mips/mti-malta/malta-init.c
drivers/firmware/pcdp.c
Add back the function implemented as a wrapper to setup_earlycon.
Reported-by: Yinghai Lu <yinghai@kernel.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 6a20dbd6ca,
"tty: Fix race condition between __tty_buffer_request_room and flush_to_ldisc"
correctly identifies an unsafe race condition between
__tty_buffer_request_room() and flush_to_ldisc(), where the consumer
flush_to_ldisc() prematurely advances the head before consuming the
last of the data committed. For example:
CPU 0 | CPU 1
__tty_buffer_request_room | flush_to_ldisc
... | ...
| count = head->commit - head->read
n = tty_buffer_alloc() |
b->commit = b->used |
b->next = n |
| if (!count) /* T */
| if (head->next == NULL) /* F */
| buf->head = head->next
In this case, buf->head has been advanced but head->commit may have
been updated with a new value.
Instead of reintroducing an unnecessary lock, fix the race locklessly.
Read the commit-next pair in the reverse order of writing, which guarantees
the commit value read is the latest value written if the head is
advancing.
Reported-by: Manfred Schlaegl <manfred.schlaegl@gmx.at>
Cc: <stable@vger.kernel.org> # 3.12.x+
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 6a20dbd6ca.
Although the commit correctly identifies an unsafe race condition
between __tty_buffer_request_room() and flush_to_ldisc(), the commit
fixes the race with an unnecessary spinlock in a lockless algorithm.
The follow-on commit, "tty: Fix lockless tty buffer race" fixes
the race locklessly.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When 'console=hvc0' is specified to the kernel parameter in x86 KVM guest,
hvc console is setup within a kthread. However, that will cause SEGV
and the boot will fail when the driver is builtin to the kernel,
because currently hvc_console_setup() is annotated with '__init'. This
patch removes '__init' to boot the guest successfully with 'console=hvc0'.
Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama@hds.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tty atomic_write_lock does not provide an exclusion guarantee for
the tty driver if the termios settings are LECHO & !OPOST. And since
it is unexpected and not allowed to call TTY buffer helpers like
tty_insert_flip_string concurrently, this may lead to crashes when
concurrect writers call pty_write. In that case the following two
writers:
* the ECHOing from a workqueue and
* pty_write from the process
race and can overflow the corresponding TTY buffer like follows.
If we look into tty_insert_flip_string_fixed_flag, there is:
int space = __tty_buffer_request_room(port, goal, flags);
struct tty_buffer *tb = port->buf.tail;
...
memcpy(char_buf_ptr(tb, tb->used), chars, space);
...
tb->used += space;
so the race of the two can result in something like this:
A B
__tty_buffer_request_room
__tty_buffer_request_room
memcpy(buf(tb->used), ...)
tb->used += space;
memcpy(buf(tb->used), ...) ->BOOM
B's memcpy is past the tty_buffer due to the previous A's tb->used
increment.
Since the N_TTY line discipline input processing can output
concurrently with a tty write, obtain the N_TTY ldisc output_lock to
serialize echo output with normal tty writes. This ensures the tty
buffer helper tty_insert_flip_string is not called concurrently and
everything is fine.
Note that this is nicely reproducible by an ordinary user using
forkpty and some setup around that (raw termios + ECHO). And it is
present in kernels at least after commit
d945cb9cce (pty: Rework the pty layer to
use the normal buffering logic) in 2.6.31-rc3.
js: add more info to the commit log
js: switch to bool
js: lock unconditionally
js: lock only the tty->ops->write call
References: CVE-2014-0196
Reported-and-tested-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sleep function was updated to put the serial port to sleep only when necessary.
This appears to resolve the errant behavior of the driver as described in
Kernel Bug 61961 – "My Exar Corp. XR17C/D152 Dual PCI UART modem does not
work with 3.8.0".
Signed-off-by: Michael Welling <mwelling@ieee.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix by including linux/uaccess.h:
drivers/tty/serial/sc16is7xx.c: In function 'sc16is7xx_ioctl':
>> drivers/tty/serial/sc16is7xx.c:861:3: error: implicit declaration of function 'copy_from_user' [-Werror=implicit-function-declaration]
>> drivers/tty/serial/sc16is7xx.c:867:3: error: implicit declaration of function 'copy_to_user' [-Werror=implicit-function-declaration]
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SC16IS7xx is a slave I2C-bus/SPI interface to a single-channel
high performance UART. The SC16IS7xx's internal register set is
backward-compatible with the widely used and widely popular 16C450.
The SC16IS7xx also provides additional advanced features such as
auto hardware and software flow control, automatic RS-485 support, and
software reset.
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit fcbee4d49f.
It wasn't quite ready to go in yet, sorry about that.
Cc: Simon Horman <horms@verge.net.au>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add earlycon support for the arm/arm64 semihosting debug serial
interface. This allows enabling a debug console when early_params are
processed. This is based on the arm64 earlyprintk smh support and is
intended to replace it.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add earlycon support for the pl011 serial port. This allows enabling
the pl011 for console when early_params are processed. This is based
on the arm64 earlyprintk support and is intended to replace it.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the generic earlycon infrastructure in place, convert the 8250
early console to use it.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This introduces generic earlycon infrastructure for serial devices
based on the 8250 earlycon. This allows for supporting earlycon option
with other serial devices. The earlycon output is enabled at the time
early_params are processed.
Only architectures that have fixmap support or have functional ioremap
when early_params are processed are supported. This is the same
restriction that the 8250 driver had.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to support FIX_EARLYCON_MEM on other arches, make the
option per arch.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: x86@kernel.org
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add driver for MEN's 16z135 High Speed UART.
The 16z135 is a memory mapped UART Core on an MCB FPGA and has 1024 byte
deep FIFO buffers for the RX and TX path. It also has configurable FIFO
fill level IRQs and data copied to and from the hardware has to be
acknowledged.
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@men.de>
Reviewed-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Zynq's UART is Cadence IP. Make this visible in the prompt in kconfig
and additional comments in the driver.
This also renames functions and symbols, as far as possible without
breaking user space API, to reflect the Cadence origin. This is achieved
through simple search and replace:
- s/XUARTPS/CDNS_UART/g
- s/xuartps/cdns_uart/g
The only exceptions are PORT_XUARTPS and the driver name, which stay as is,
due to their exposure to user space. As well as the - no legacy -
compatibility string 'xlnx,xuartps'
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A comment states, that, according to the data sheet, to enable
interrupts the disable register should be written, but the enable
register could be left untouched. And it suspsects a HW bug requiring
to write both.
Reviewing the data sheet, these statements seem wrong. Just as one would
expect. Writing to the enable/disable register enables/disables
interrupts.
Hence the misleading comment and needless write to the disable register
are removed from the enable sequence.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A lot of read-modify-write sequences used a one-line statement which
nests a readl() within a writel(). Convert this into code sequences that
make the three steps more obvious.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Print a warning if the clock notifier rejects a clock frequency change
to facilitate debugging (see:
http://thread.gmane.org/gmane.linux.ports.arm.kernel/304329/focus=304379)
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is all white space and comment clean up. Mostly reformatting
comments.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Register port numbers according to order in DT aliases.
If aliases are not defined, order in DT is used.
If aliases are defined, register port id based
on that.
This patch ensures proper ttyPS0/1 assignment.
[soren]: Combined integer declarations in probe(), removed warning message
if no alias is found.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
nobody passes a DTR_gpio to this driver, so
this code is not necessary.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
just using helper function to remove some duplicated
code a bit. While at that, also move allocation of
struct uart_omap_port higher in the code so that
we return much earlier in case of no memory.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
this way we can remove one pointer declaration.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
this will make sure gpio gets freed automatically
when this device is destroyed.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
per CodingStyle we should have those braces, no
functional changes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 0324a82102.
That commit tried to fix a deadlock problem when using
hci_ldisc, but it turns out the bug was in hci_ldsic
all along where it was calling ->write() from within
->write_wakeup() callback.
The problem is that ->write_wakeup() was called with
port lock held and ->write() tried to grab the same
port lock.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In (efe2f29 kgdboc,kdb: Allow kdb to work on a non open console port)
support was added to directly use the "write_char" functions when
doing kdb over a non-open console port. This is great, but it ends up
bypassing the normal code in uart_console_write() that adds a carriage
return before any newlines.
There appears to have been a trend to add this support directly in
some console driver's poll_put_char() functions. This had a few side
effects, including:
- In this case we were doing LFCR, not CRLF. This was fixed in
uart_console_write() back in (d358788 [SERIAL] kernel console should
send CRLF not LFCR)
- Not all serial drivers had the LFCR code in their poll_put_char()
functions. In my case I was running serial/samsung.c which lacked
it.
I've moved the handling to uart_poll_put_char() to fix the above
problems. Now when I use kdb (and don't point console= to the same
UART) I no longer get:
[0]kdb>
[0]kdb>
[0]kdb>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use del_timer_sync to ensure that the timer is stopped on all CPUs before
the driver exists.
This change was suggested by Thomas Gleixner.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
declarer name module_exit;
identifier ex;
@@
module_exit(ex);
@@
identifier r.ex;
@@
ex(...) {
<...
- del_timer
+ del_timer_sync
(...)
...>
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mux driver is anomalous among all the serial drivers that can
define SUPPORT_SYSRQ because it can, with some configs, set
SUPPORT_SYSRQ when SERIAL_CORE_CONSOLE is not set.
Not only does this impose a pointless (but tiny) runtime overhead for
such configs but, more significantly, it adds needless complexity when
doing a code review to check for unexpected side effects of any
changes to the serial core.
This is (cross-)compile tested only because I do not have any PA-RISC
hardware.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the platform data for the legacy-C initialisation of sh-sci
for the r8a7779 SoC and my own testing the SCIx_SH4_SCIF_REGTYPE bit of
scscr needs to be set.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the same manner as 8250_pci, 8250_dw needs some
baytrail specific quirks to be used. The reference
clock needs to be adjusted before divided in order
to have the minimum error rate on the baudrate.
The specific byt set termios function is stored in
the driver_data field of the acpi device id via the
dw8250_acpi_desc structure.
Remove the uartclk field which is no longer delivered
as driver data.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This will additionally show the specific UART device instead of the
general module name. This cames in handy so check for the interupts of
a specific device if there are several of them.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While porting a RS485 driver from 2.6.29 to 3.14, i noticed that the serial tty
driver could break it by using uart ports that it does not own :
1. uart_change_pm ist called during uart_open and calls the uart pm function
without checking for PORT_UNKNOWN.
The fix is to move uart_change_pm from uart_open to uart_port_startup.
2. The return code from the uart request_port call in uart_set_info is not
handled properly, leading to the situation that the serial driver also
thinks it owns the uart ports.
This can triggered by doing following actions :
setserial /dev/ttyS0 uart none # release the uart ports
modprobe lirc-serial # or any other device that uses the uart
setserial /dev/ttyS0 uart 16550 # gives no error and the uart tty driver
# can use the ports as well
Signed-off-by: Thomas Pfaff <tpfaff@pcs.com>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The two functions to write out to the console (one used in normal
console mode and one in polling console mode) were slightly different.
One used a barrier() in its loop and the other a cpu_relax(). The
barrier() really doesn't do anything since we're using rd_regl() to
read the port anyway. Switch it to cpu_relax() to make things
consistent.
No known bugs / issues are fixed by this change--it just makes things
more consistent.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The s3c24xx_serial_console_putchar() is _only_ ever used by
s3c24xx_serial_console_write() and is called in a loop (indirectly
through uart_console_write()). There's no reason to call
s3c24xx_port_configured() for every iteration through the loop. Move
it outside the loop.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The two functions in the samsung serial driver used for writing
characters out to the port were inconsistent about whether they used
the passed in "port" or the global "cons_uart". There was no reason
to use the global and the use of the global in
s3c24xx_serial_put_poll_char() caused a crash in the case where you
used the serial port for kgdboc but not for console.
Fix it so we used the passed in variable.
Note that this doesn't fix all problems with the samsung serial
driver. Specifically:
* s3c24xx_serial_console_putchar() is still 99% identical to
s3c24xx_serial_put_poll_char() (the function signature is different,
but that's about it). A future patch will make them slightly less
identical and judging by other serial drivers we may need yet more
differences eventually.
* The samsung serial driver still doesn't allow you to have more than
one console port since it still uses the global cons_uart in
s3c24xx_serial_console_write().
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__dma_tx_complete is not protected against concurrent
call of serial8250_tx_dma. it can lead to circular tail
index corruption or parallel call of serial_tx_dma on the
same data portion.
This patch fixes this issue by holding the port lock.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On transmit-hold-register empty, serial8250_tx_chars
should be called only if we don't use DMA.
DMA has its own tx cycle.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The race was introduced while development of linux-3.11 by
e8437d7ecb and
e9975fdec0.
Originally it was found and reproduced on linux-3.12.15 and
linux-3.12.15-rt25, by sending 500 byte blocks with 115kbaud to the
target uart in a loop with 100 milliseconds delay.
In short:
1. The consumer flush_to_ldisc is on to remove the head tty_buffer.
2. The producer adds a number of bytes, so that a new tty_buffer must
be allocated and added by __tty_buffer_request_room.
3. The consumer removes the head tty_buffer element, without handling
newly committed data.
Detailed example:
* Initial buffer:
* Head, Tail -> 0: used=250; commit=250; read=240; next=NULL
* Consumer: ''flush_to_ldisc''
* consumed 10 Byte
* buffer:
* Head, Tail -> 0: used=250; commit=250; read=250; next=NULL
{{{
count = head->commit - head->read; // count = 0
if (!count) { // enter
// INTERRUPTED BY PRODUCER ->
if (head->next == NULL)
break;
buf->head = head->next;
tty_buffer_free(port, head);
continue;
}
}}}
* Producer: tty_insert_flip_... 10 bytes + tty_flip_buffer_push
* buffer:
* Head, Tail -> 0: used=250; commit=250; read=250; next=NULL
* added 6 bytes: head-element filled to maximum.
* buffer:
* Head, Tail -> 0: used=256; commit=250; read=250; next=NULL
* added 4 bytes: __tty_buffer_request_room is called
* buffer:
* Head -> 0: used=256; commit=256; read=250; next=1
* Tail -> 1: used=4; commit=0; read=250 next=NULL
* push (tty_flip_buffer_push)
* buffer:
* Head -> 0: used=256; commit=256; read=250; next=1
* Tail -> 1: used=4; commit=4; read=250 next=NULL
* Consumer
{{{
count = head->commit - head->read;
if (!count) {
// INTERRUPTED BY PRODUCER <-
if (head->next == NULL) // -> no break
break;
buf->head = head->next;
tty_buffer_free(port, head);
// ERROR: tty_buffer head freed -> 6 bytes lost
continue;
}
}}}
This patch reintroduces a spin_lock to protect this case. Perhaps later
a lock-less solution could be found.
Signed-off-by: Manfred Schlaegl <manfred.schlaegl@gmx.at>
Cc: stable <stable@vger.kernel.org> # 3.11
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit f4f653e987.
Jiri writes:
No, please drop this one. We need a better solution as it turned
out that some boxes need 16k loops and it will increase with new
processors :(.
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Martin Pluskal <mpluskal@suse.com>
Cc: Takashi Iwai <tiwai@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A recent commit ef2889f7ff "serial: pl011:
Move uart_register_driver call to device probe" introduced a regression,
causing the pl011 driver to Oops if more than 1 port have been probed. Fix
the Oops by only calling uart_unregister_driver() once after the last port
has been removed.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 8250 driver now reports many of these:
serial8250: too much work for irq4
These messages turned out to be common these days with a use of
virtualization. I tried to increase the limit of processed characters
in commit e7328ae184 (serial: 8250,
increase PASS_LIMIT) in 2011. It was raised from 256 to 512, but it is
still not enough, apparently.
So disable the warning unless somebody turns on DEBUG (or
DYNAMIC_DEBUG _and_ the message).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: Martin Pluskal <mpluskal@suse.com>
Reported-by: Takashi Iwai <tiwai@suse.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
References: https://bugzilla.novell.com/show_bug.cgi?id=868394
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The lack of pm_runtime_resume handling for the device state leads into
device wake-up interrupts not working after a while for runtime PM.
Also, serial-omap is confused about the use of device_may_wakeup.
The checks for device_may_wakeup should only be done for suspend and
resume, not for pm_runtime_suspend and pm_runtime_resume. The wake-up
events for PM runtime should always be enabled.
The lack of pm_runtime_resume handling leads into device wake-up
interrupts not working after a while for runtime PM.
Rather than try to patch over the issue of adding complex tests to
the pm_runtime_resume, let's fix the issues properly:
1. Make serial_omap_enable_wakeup deal with all internal PM state
handling so we don't need to test for up->wakeups_enabled elsewhere.
Later on once omap3 boots in device tree only mode we can also
remove the up->wakeups_enabled flag and rely on the wake-up
interrupt enable/disable state alone.
2. Do the device_may_wakeup checks in suspend and resume only,
for runtime PM the wake-up events need to be always enabled.
3. Finally just call serial_omap_enable_wakeup and make sure we
call it also in pm_runtime_resume.
4. Note that we also have to use disable_irq_nosync as serial_omap_irq
calls pm_runtime_get_sync.
Fixes: 2a0b965cfb (serial: omap: Add support for optional wake-up)
Cc: stable@vger.kernel.org # v3.13+
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is closed, uart_close() takes care of shutting down the
hardware, and powering it down.
When a serial port is unbound while in use, uart_close() bypasses all of
this, as this is supposed to be done through uart_hangup() (invoked via
tty_vhangup() in uart_remove_one_port()).
However, uart_hangup() does not set the hardware's power state, leaving it
powered up. This may also lead to unbounded nesting counts in clock and
power management, depending on their internal implementation.
Make sure to power down the port in uart_hangup(), except when the port is
used as a serial console.
For serial consoles, this operation must be postponed until after the port
becomes completely unused. This case is not fixed yet, as it depends on a
(future) fix for the tty->count vs. port->count imbalance on failed
uart_open().
After this, the module clock used by the sh-sci driver is disabled on
unbind while the serial port is in use.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The amba-pl011.c driver sets DMA burst size equal to FIFO trigger level.
If now exactly DMA burst size bytes are received, the DMAC will retrieve
them all and no Rx timeout interrupt will be generated. To fix that set
the burst size to half the FIFO trigger level.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As far as I know the Timberdale chip was only used as a companion for
Intel Atom E600 series processors. As such, its drivers are only
useful on X86_32.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver, like several others, uses the upper bits of the character
to track both real and dummy state. Unfortunately it neglects to mask
these bits properly when passing the character data around. This means
neither break detection nor sysrq character handling work correctly.
This patch adds the requires masking and has been tested to confirm
that it correctly handles magic sysrq sequences on ST's B2020 board.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 63e3ad3252,
since this not works as expected and produce runtime error:
BUG: sleeping function called from invalid context at drivers/tty/serial/clps711x.c:379
in_atomic(): 0, irqs_disabled(): 128, pid: 287, name: mount
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the serial_core ring buffer empties just as the tty layer receives
an XOFF, then start_tx will never be called when the tty layer
receives an XON as the serial_core ring buffer is empty. This will
possibly leave a few bytes trapped in the fifo for drivers that
disable the transmitter when flow controlled.
Signed-off-by: Seth Bollinger <sethb@digi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wolfram Sang pointed out that "efm32,$device" is non-standard. So use the
common scheme and prefix device with "efm32-". The old compatible string
is left in place until arch/arm/boot/dts/efm32* is fixed.
Reported-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull audit updates from Eric Paris.
* git://git.infradead.org/users/eparis/audit: (28 commits)
AUDIT: make audit_is_compat depend on CONFIG_AUDIT_COMPAT_GENERIC
audit: renumber AUDIT_FEATURE_CHANGE into the 1300 range
audit: do not cast audit_rule_data pointers pointlesly
AUDIT: Allow login in non-init namespaces
audit: define audit_is_compat in kernel internal header
kernel: Use RCU_INIT_POINTER(x, NULL) in audit.c
sched: declare pid_alive as inline
audit: use uapi/linux/audit.h for AUDIT_ARCH declarations
syscall_get_arch: remove useless function arguments
audit: remove stray newline from audit_log_execve_info() audit_panic() call
audit: remove stray newlines from audit_log_lost messages
audit: include subject in login records
audit: remove superfluous new- prefix in AUDIT_LOGIN messages
audit: allow user processes to log from another PID namespace
audit: anchor all pid references in the initial pid namespace
audit: convert PPIDs to the inital PID namespace.
pid: get pid_t ppid of task in init_pid_ns
audit: rename the misleading audit_get_context() to audit_take_context()
audit: Add generic compat syscall support
audit: Add CONFIG_HAVE_ARCH_AUDITSYSCALL
...
The firmware can notify us when new input data is available, so
let's make sure we wakeup the HVC thread in that case.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
These changes are mostly for ARM specific device drivers that either
don't have an upstream maintainer, or that had the maintainer ask
us to pick up the changes to avoid conflicts. A large chunk of this
are clock drivers (bcm281xx, exynos, versatile, shmobile), aside from
that, reset controllers for STi as well as a large rework of the
Marvell Orion/EBU watchdog driver are notable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=u/FI
-----END PGP SIGNATURE-----
Merge tag 'drivers-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Arnd Bergmann:
"These changes are mostly for ARM specific device drivers that either
don't have an upstream maintainer, or that had the maintainer ask us
to pick up the changes to avoid conflicts.
A large chunk of this are clock drivers (bcm281xx, exynos, versatile,
shmobile), aside from that, reset controllers for STi as well as a
large rework of the Marvell Orion/EBU watchdog driver are notable"
* tag 'drivers-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
Revert "dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac."
Revert "net: stmmac: Add SOCFPGA glue driver"
ARM: shmobile: r8a7791: Fix SCIFA3-5 clocks
ARM: STi: Add reset controller support to mach-sti Kconfig
drivers: reset: stih416: add softreset controller
drivers: reset: stih415: add softreset controller
drivers: reset: Reset controller driver for STiH416
drivers: reset: Reset controller driver for STiH415
drivers: reset: STi SoC system configuration reset controller support
dts: socfpga: Add sysmgr node so the gmac can use to reference
dts: socfpga: Add support for SD/MMC on the SOCFPGA platform
reset: Add optional resets and stubs
ARM: shmobile: r7s72100: fix bus clock calculation
Power: Reset: Generalize qnap-poweroff to work on Synology devices.
dts: socfpga: Update clock entry to support multiple parents
ARM: socfpga: Update socfpga_defconfig
dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
net: stmmac: Add SOCFPGA glue driver
watchdog: orion_wdt: Use %pa to print 'phys_addr_t'
drivers: cci: Export CCI PMU revision
...
These cleanup patches are mainly move stuff around and should all
be harmless. They are mainly split out so that other branches can
be based on top to avoid conflicts.
Notable changes are:
* We finally remove all mach/timex.h, after CLOCK_TICK_RATE is no
longer used. (Uwe Kleine-König)
* The Qualcomm MSM platform is split out into legacy mach-msm and
new-style mach-qcom, to allow easier maintainance of the new
hardware support without regressions. (Kumar Gala)
* A rework of some of the Kconfig logic to simplify multiplatform
support (Rob Herring)
* Samsung Exynos gets closer to supporting multiplatform (Sachin
Kamat and others)
* mach-bcm3528 gets merged into mach-bcm (Stephen Warren)
* at91 gains some common clock framework support (Alexandre Belloni,
Jean-Jacques Hiblot and other French people).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=GcBb
-----END PGP SIGNATURE-----
Merge tag 'cleanup-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Arnd Bergmann:
"These cleanup patches are mainly move stuff around and should all be
harmless. They are mainly split out so that other branches can be
based on top to avoid conflicts.
Notable changes are:
- We finally remove all mach/timex.h, after CLOCK_TICK_RATE is no
longer used (Uwe Kleine-König)
- The Qualcomm MSM platform is split out into legacy mach-msm and
new-style mach-qcom, to allow easier maintainance of the new
hardware support without regressions (Kumar Gala)
- A rework of some of the Kconfig logic to simplify multiplatform
support (Rob Herring)
- Samsung Exynos gets closer to supporting multiplatform (Sachin
Kamat and others)
- mach-bcm3528 gets merged into mach-bcm (Stephen Warren)
- at91 gains some common clock framework support (Alexandre Belloni,
Jean-Jacques Hiblot and other French people)"
* tag 'cleanup-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (89 commits)
ARM: hisi: select HAVE_ARM_SCU only for SMP
ARM: efm32: allow uncompress debug output
ARM: prima2: build reset code standalone
ARM: at91: add PWM clock
ARM: at91: move sam9261 SoC to common clk
ARM: at91: prepare common clk transition for sam9261 SoC
ARM: at91: updated the at91_dt_defconfig with support for the ADS7846
ARM: at91: dt: sam9261: Device Tree support for the at91sam9261ek
ARM: at91: dt: defconfig: Added the sam9261 to the list of DT-enabled SOCs
ARM: at91: dt: Add at91sam9261 dt SoC support
ARM: at91: switch sam9rl to common clock framework
ARM: at91/dt: define main clk frequency of at91sam9rlek
ARM: at91/dt: define at91sam9rl clocks
ARM: at91: prepare common clk transition for sam9rl SoCs
ARM: at91: prepare sam9 dt boards transition to common clk
ARM: at91: dt: sam9rl: Device Tree for the at91sam9rlek
ARM: at91/defconfig: Add the sam9rl to the list of DT-enabled SOCs
ARM: at91: Add at91sam9rl DT SoC support
ARM: at91: prepare at91sam9rl DT transition
ARM: at91/defconfig: refresh at91sam9260_9g20_defconfig
...
Here's the big tty/serial driver update for 3.15-rc1.
Nothing major, a number of serial driver updates and a few tty core
fixes as well.
All have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlM7CWAACgkQMUfUDdst+ylDXACg0vZ+J+5OXbbE3lywVCAebjhB
XzkAn1lz7JRIils7IlckAJ2w/m50b174
=M+8c
-----END PGP SIGNATURE-----
Merge tag 'tty-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver update from Greg KH:
"Here's the big tty/serial driver update for 3.15-rc1.
Nothing major, a number of serial driver updates and a few tty core
fixes as well.
All have been in linux-next for a while"
* tag 'tty-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (71 commits)
tty/serial: omap: empty the RX FIFO at the end of half-duplex TX
tty/serial: omap: fix RX interrupt enable/disable in half-duplex TX
serial: sh-sci: Neaten dev_<level> uses
serial: sh-sci: Replace hardcoded 3 by UART_PM_STATE_OFF
serial: sh-sci: Add more register documentation
serial: sh-sci: Remove useless casts
serial: sh-sci: Replace printk() by pr_*()
serial_core: Avoid NULL pointer dereference in uart_close()
serial_core: Get a reference for port->tty in uart_remove_one_port()
serial: clps711x: Give a chance to perform useful tasks during wait loop
serial_core: Grammar s/ports/port's/
serial_core: Spelling s/contro/control/
serial: efm32: properly namespace location property
serial: max310x: Add missing #include <linux/uaccess.h>
synclink: fix info leak in ioctl
serial: 8250: Clean up the locking for -rt
serial: 8250_pci: change BayTrail default uartclk
serial: 8250_pci: more BayTrail error-free bauds
serial: sh-sci: Add missing call to uart_remove_one_port() in failure path
serial_core: Unregister console in uart_remove_one_port()
...
- Device PM QoS support for latency tolerance constraints on systems with
hardware interfaces allowing such constraints to be specified. That is
necessary to prevent hardware-driven power management from becoming
overly aggressive on some systems and to prevent power management
features leading to excessive latencies from being used in some cases.
- Consolidation of the handling of ACPI hotplug notifications for device
objects. This causes all device hotplug notifications to go through
the root notify handler (that was executed for all of them anyway
before) that propagates them to individual subsystems, if necessary,
by executing callbacks provided by those subsystems (those callbacks
are associated with struct acpi_device objects during device
enumeration). As a result, the code in question becomes both smaller
in size and more straightforward and all of those changes should not
affect users.
- ACPICA update, including fixes related to the handling of _PRT in cases
when it is broken and the addition of "Windows 2013" to the list of
supported "features" for _OSI (which is necessary to support systems
that work incorrectly or don't even boot without it). Changes from
Bob Moore and Lv Zheng.
- Consolidation of ACPI _OST handling from Jiang Liu.
- ACPI battery and AC fixes allowing unusual system configurations to
be handled by that code from Alexander Mezin.
- New device IDs for the ACPI LPSS driver from Chiau Ee Chew.
- ACPI fan and thermal optimizations related to system suspend and resume
from Aaron Lu.
- Cleanups related to ACPI video from Jean Delvare.
- Assorted ACPI fixes and cleanups from Al Stone, Hanjun Guo, Lan Tianyu,
Paul Bolle, Tomasz Nowicki.
- Intel RAPL (Running Average Power Limits) driver cleanups from Jacob Pan.
- intel_pstate fixes and cleanups from Dirk Brandewie.
- cpufreq fixes related to system suspend/resume handling from Viresh Kumar.
- cpufreq core fixes and cleanups from Viresh Kumar, Stratos Karafotis,
Saravana Kannan, Rashika Kheria, Joe Perches.
- cpufreq drivers updates from Viresh Kumar, Zhuoyu Zhang, Rob Herring.
- cpuidle fixes related to the menu governor from Tuukka Tikkanen.
- cpuidle fix related to coupled CPUs handling from Paul Burton.
- Asynchronous execution of all device suspend and resume callbacks,
except for ->prepare and ->complete, during system suspend and resume
from Chuansheng Liu.
- Delayed resuming of runtime-suspended devices during system suspend for
the PCI bus type and ACPI PM domain.
- New set of PM helper routines to allow device runtime PM callbacks to
be used during system suspend and resume more easily from Ulf Hansson.
- Assorted fixes and cleanups in the PM core from Geert Uytterhoeven,
Prabhakar Lad, Philipp Zabel, Rashika Kheria, Sebastian Capella.
- devfreq fix from Saravana Kannan.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=ywR6
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"The majority of this material spent some time in linux-next, some of
it even several weeks. There are a few relatively fresh commits in
it, but they are mostly fixes and simple cleanups.
ACPI took the lead this time, both in terms of the number of commits
and the number of modified lines of code, cpufreq follows and there
are a few changes in the PM core and in cpuidle too.
A new feature that already got some LWN.net's attention is the device
PM QoS extension allowing latency tolerance requirements to be
propagated from leaf devices to their ancestors with hardware
interfaces for specifying latency tolerance. That should help systems
with hardware-driven power management to avoid going too far with it
in cases when there are latency tolerance constraints.
There also are some significant changes in the ACPI core related to
the way in which hotplug notifications are handled. They affect PCI
hotplug (ACPIPHP) and the ACPI dock station code too. The bottom line
is that all those notification now go through the root notify handler
and are propagated to the interested subsystems by means of callbacks
instead of having to install a notify handler for each device object
that we can potentially get hotplug notifications for.
In addition to that ACPICA will now advertise "Windows 2013"
compatibility for _OSI, because some systems out there don't work
correctly if that is not done (some of them don't even boot).
On the system suspend side of things, all of the device suspend and
resume callbacks, except for ->prepare() and ->complete(), are now
going to be executed asynchronously as that turns out to speed up
system suspend and resume on some platforms quite significantly and we
have a few more optimizations in that area.
Apart from that, there are some new device IDs and fixes and cleanups
all over. In particular, the system suspend and resume handling by
cpufreq should be improved and the cpuidle menu governor should be a
bit more robust now.
Specifics:
- Device PM QoS support for latency tolerance constraints on systems
with hardware interfaces allowing such constraints to be specified.
That is necessary to prevent hardware-driven power management from
becoming overly aggressive on some systems and to prevent power
management features leading to excessive latencies from being used
in some cases.
- Consolidation of the handling of ACPI hotplug notifications for
device objects. This causes all device hotplug notifications to go
through the root notify handler (that was executed for all of them
anyway before) that propagates them to individual subsystems, if
necessary, by executing callbacks provided by those subsystems
(those callbacks are associated with struct acpi_device objects
during device enumeration). As a result, the code in question
becomes both smaller in size and more straightforward and all of
those changes should not affect users.
- ACPICA update, including fixes related to the handling of _PRT in
cases when it is broken and the addition of "Windows 2013" to the
list of supported "features" for _OSI (which is necessary to
support systems that work incorrectly or don't even boot without
it). Changes from Bob Moore and Lv Zheng.
- Consolidation of ACPI _OST handling from Jiang Liu.
- ACPI battery and AC fixes allowing unusual system configurations to
be handled by that code from Alexander Mezin.
- New device IDs for the ACPI LPSS driver from Chiau Ee Chew.
- ACPI fan and thermal optimizations related to system suspend and
resume from Aaron Lu.
- Cleanups related to ACPI video from Jean Delvare.
- Assorted ACPI fixes and cleanups from Al Stone, Hanjun Guo, Lan
Tianyu, Paul Bolle, Tomasz Nowicki.
- Intel RAPL (Running Average Power Limits) driver cleanups from
Jacob Pan.
- intel_pstate fixes and cleanups from Dirk Brandewie.
- cpufreq fixes related to system suspend/resume handling from Viresh
Kumar.
- cpufreq core fixes and cleanups from Viresh Kumar, Stratos
Karafotis, Saravana Kannan, Rashika Kheria, Joe Perches.
- cpufreq drivers updates from Viresh Kumar, Zhuoyu Zhang, Rob
Herring.
- cpuidle fixes related to the menu governor from Tuukka Tikkanen.
- cpuidle fix related to coupled CPUs handling from Paul Burton.
- Asynchronous execution of all device suspend and resume callbacks,
except for ->prepare and ->complete, during system suspend and
resume from Chuansheng Liu.
- Delayed resuming of runtime-suspended devices during system suspend
for the PCI bus type and ACPI PM domain.
- New set of PM helper routines to allow device runtime PM callbacks
to be used during system suspend and resume more easily from Ulf
Hansson.
- Assorted fixes and cleanups in the PM core from Geert Uytterhoeven,
Prabhakar Lad, Philipp Zabel, Rashika Kheria, Sebastian Capella.
- devfreq fix from Saravana Kannan"
* tag 'pm+acpi-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (162 commits)
PM / devfreq: Rewrite devfreq_update_status() to fix multiple bugs
PM / sleep: Correct whitespace errors in <linux/pm.h>
intel_pstate: Set core to min P state during core offline
cpufreq: Add stop CPU callback to cpufreq_driver interface
cpufreq: Remove unnecessary braces
cpufreq: Fix checkpatch errors and warnings
cpufreq: powerpc: add cpufreq transition latency for FSL e500mc SoCs
MAINTAINERS: Reorder maintainer addresses for PM and ACPI
PM / Runtime: Update runtime_idle() documentation for return value meaning
video / output: Drop display output class support
fujitsu-laptop: Drop unneeded include
acer-wmi: Stop selecting VIDEO_OUTPUT_CONTROL
ACPI / gpu / drm: Stop selecting VIDEO_OUTPUT_CONTROL
ACPI / video: fix ACPI_VIDEO dependencies
cpufreq: remove unused notifier: CPUFREQ_{SUSPENDCHANGE|RESUMECHANGE}
cpufreq: Do not allow ->setpolicy drivers to provide ->target
cpufreq: arm_big_little: set 'physical_cluster' for each CPU
cpufreq: arm_big_little: make vexpress driver depend on bL core driver
ACPI / button: Add ACPI Button event via netlink routine
ACPI: Remove duplicate definitions of PREFIX
...
Pull core locking updates from Ingo Molnar:
"The biggest change is the MCS spinlock generalization changes from Tim
Chen, Peter Zijlstra, Jason Low et al. There's also lockdep
fixes/enhancements from Oleg Nesterov, in particular a false negative
fix related to lockdep_set_novalidate_class() usage"
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (22 commits)
locking/mutex: Fix debug checks
locking/mutexes: Add extra reschedule point
locking/mutexes: Introduce cancelable MCS lock for adaptive spinning
locking/mutexes: Unlock the mutex without the wait_lock
locking/mutexes: Modify the way optimistic spinners are queued
locking/mutexes: Return false if task need_resched() in mutex_can_spin_on_owner()
locking: Move mcs_spinlock.h into kernel/locking/
m68k: Skip futex_atomic_cmpxchg_inatomic() test
futex: Allow architectures to skip futex_atomic_cmpxchg_inatomic() test
Revert "sched/wait: Suppress Sparse 'variable shadowing' warning"
lockdep: Change lockdep_set_novalidate_class() to use _and_name
lockdep: Change mark_held_locks() to check hlock->check instead of lockdep_no_validate
lockdep: Don't create the wrong dependency on hlock->check == 0
lockdep: Make held_lock->check and "int check" argument bool
locking/mcs: Allow architecture specific asm files to be used for contended case
locking/mcs: Order the header files in Kbuild of each architecture in alphabetical order
sched/wait: Suppress Sparse 'variable shadowing' warning
hung_task/Documentation: Fix hung_task_warnings description
locking/mcs: Allow architectures to hook in to contended paths
locking/mcs: Micro-optimize the MCS code, add extra comments
...
Store and log all PIDs with reference to the initial PID namespace and
use the access functions task_pid_nr() and task_tgid_nr() for task->pid
and task->tgid.
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
(informed by ebiederman's c776b5d2)
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Two cpufreq notifiers CPUFREQ_RESUMECHANGE and CPUFREQ_SUSPENDCHANGE have
not been used for some time, so remove them to clean up code a bit.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
[rjw: Changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Provided that the SER_RS485_RX_DURING_TX flag is not set, empty the
RX FIFO to prevent reading back the transmitted data.
Signed-off-by: Dimitris Lampridis <dlampridis@logikonlabs.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure that serial_omap_stop_rx() also disables RDI (Receiver Data Interrupt),
otherwise the interrupt handler will call serial_omap_rdi() to read the new data,
resulting in the transmission being echoed back.
When the half-duplex transmission is complete, in order to reverse the effects of
serial_omap_stop_rx(), we should re-enable:
* the RX interrupts _without_ overwriting up->ier
* the UART_LSR_DR bit of the up->port.read_status_mask
Signed-off-by: Dimitris Lampridis <dlampridis@logikonlabs.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make banner const while we're at it
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Simon Horman <horms@verge.net.au>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When unbinding a serial driver that's being used as a serial console,
the kernel may crash with a NULL pointer dereference in a uart_*() function
called from uart_close () (e.g. uart_flush_buffer() or
uart_chars_in_buffer()).
To fix this, let uart_close() check for port->count == 0. If this is the
case, bail out early. Else tty_port_close_start() will make the port
counts inconsistent, printing out warnings like
tty_port_close_start: tty->count = 1 port count = 0.
and
tty_port_close_start: count = -1
and once uport == NULL, it will also crash.
Also fix the related crash in pr_debug() by checking for a non-NULL uport
first.
Detailed description:
On driver unbind, uart_remove_one_port() is called. Basically it;
- marks the port dead,
- calls tty_vhangup(),
- sets state->uart_port = NULL.
What will happen depends on whether the port is just in use by e.g. getty,
or was also opened as a console.
A. If the tty was not opened as a console:
- tty_vhangup() will (in __tty_hangup()):
- mark all file descriptors for this tty hung up by pointing them to
hung_up_tty_fops,
- call uart_hangup(), which sets port->count to 0.
- A subsequent uart_open() (this may be through /dev/ttyS*, or through
/dev/console if this is a serial console) will fail with -ENXIO as the
port was marked dead,
- uart_close() after the failed uart_open() will return early, as
tty_hung_up_p() (called from tty_port_close_start()) will notice it was
hung up.
B. If the tty was also opened as a console:
- tty_vhangup() will (in __tty_hangup()):
- mark non-console file descriptors for this tty hung up by pointing
them to hung_up_tty_fops,
- NOT call uart_hangup(), but instead call uart_close() for every
non-console file descriptor, so port->count will still have a
non-zero value afterwards.
- A subsequent uart_open() will fail with -ENXIO as the port was
marked dead,
- uart_close() after the failed uart_open() starts to misbehave:
- tty_hung_up_p() will not notice it was hung up,
- As port->count is non-zero, tty_port_close_start() will decrease
port->count, making the tty and port counts inconsistent. Later,
warnings like these will be printed:
tty_port_close_start: tty->count = 1 port count = 0.
and
tty_port_close_start: count = -1
- If all of this happens after state->uart_port was set to zero, a
NULL pointer dereference will happen.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds cond_sched() calls during wait loop to perform
other tasks.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While reviewing an i2c driver for efm32 that needs a similar property
Wolfram Sang pointed out that "location" is a too generic name for something
that is efm32 specific. So add an appropriate namespace and fall back to the
generic name in case of failure.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cris allmodconfig:
drivers/tty/serial/max310x.c: In function 'max310x_ioctl':
drivers/tty/serial/max310x.c:885:3: error: implicit declaration of function 'copy_from_user' [-Werror=implicit-function-declaration]
drivers/tty/serial/max310x.c:916:3: error: implicit declaration of function 'copy_to_user' [-Werror=implicit-function-declaration]
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hdlcdev_ioctl() code fails to initialize the two padding bytes of
struct sync_serial_settings after the ->loopback member. Add an explicit
memset(0) before filling the structure to avoid the info leak.
Signed-off-by: Salva Peiró <speiro@ai2.upv.es>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In -RT the spin_lock_irqsave() does not spin but sleep if the lock is
taken. Before that, local_irq_save() is invoked which disables
interrupts even on -RT. Therefore local_irq_save() + spin_lock() does not
work.
In the ->sysrq and oops_in_progress case it is save to trylock the lock
i.e. this is what we do now anyway except for ->sysrq where we assume
that the lock is already taken.
The spin_lock_irqsave() grabs the lock and disables the interrupts on
vanilla (the same behavior) and on -RT it won't disable interrupts.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[bigeasy: add a patch description]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support the following additional baud rates with 0% error:
500000, 1500000, 2500000, 3500000
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJS3IyXAAoJEHm+PkMAQRiGplAH/ilCikBrCHyZ2938NHNLm+j1
yhfYnEJHLNg7T69KEj3p0cNagO3v9RPWM6UYFBQ6uFIYNN1MBKO7U+mCZuMWzeO8
+tGMV3mn5wx+oYn1RnWCCweQx5AESEl6rYn8udPDKh7LfW5fCLV60jguUjVSQ9IQ
cvtKlWknbiHyM7t1GoYgzN7jlPrRQvcNQZ+Aogzz7uSnJAgwINglBAHS7WP2tiEM
HAU2FoE4b3MbfGaid1vypaYQPBbFebx7Bw2WxAuZhkBbRiUBKlgF0/SYhOTvH38a
Sjpj1EHKfjcuCBt9tht6KP6H56R25vNloGR2+FB+fuQBdujd/SPa9xDflEMcdG4=
=iXnG
-----END PGP SIGNATURE-----
Merge tag 'v3.13' into for-3.15
Linux 3.13
Conflicts:
include/net/xfrm.h
Simple merge where v3.13 removed 'extern' from definitions and the audit
tree did s/u32/unsigned int/ to the same definitions.
If cpufreq_register_notifier() fails, we have to remove the port added by
sci_probe_single(), which is not done by sci_cleanup_single().
Else the serial port stays active from the point of view of the serial
subsystem, and it may crash when userspace getty is started, or when the
loadable driver module is unloaded.
This was introduced by commit 6dae14216c
("serial: sh-sci: Fix probe error paths").
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the serial port being removed is used as a console, it must also be
unregistered from the console subsystem using unregister_console().
uart_ops.release_port() will release resources (e.g. iounmap() the serial
port registers), causing a crash on subsequent kernel output if the console
is still registered.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 95e629b761 removed the use of board
specific hooks in serial_at91.h, so now, the open/close hook are just
dead code.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'active' sysfs attribute should refer to the currently active tty
devices the console is running on, not the currently active console. The
console structure doesn't refer to any device in sysfs, only the tty the
console is running on has. So we need to print out the tty names in
'active', not the console names.
There is one special-case, which is tty0. If the console is directed to
it, we want 'tty0' to show up in the file, so user-space knows that the
messages get forwarded to the active VT. The ->device() callback would
resolve tty0, though. Hence, treat it special and don't call into the VT
layer to resolve it (plymouth is known to depend on it).
Cc: Lennart Poettering <lennart@poettering.net>
Cc: Kay Sievers <kay@vrfy.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Werner Fink <werner@suse.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_ioremap_resource() in order to make the code simpler and
it gives proper codes on errors.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The user-settable knob, low_latency, has been the source of
several BUG reports which stem from flush_to_ldisc() running
in interrupt context. Since 3.12, which added several sleeping
locks (termios_rwsem and buf->lock) to the input processing path,
the frequency of these BUG reports has increased.
Note that changes in 3.12 did not introduce this regression;
sleeping locks were first added to the input processing path
with the removal of the BKL from N_TTY in commit
a88a69c912,
'n_tty: Fix loss of echoed characters and remove bkl from n_tty'
and later in commit 38db89799b,
'tty: throttling race fix'. Since those changes, executing
flush_to_ldisc() in interrupt_context (ie, low_latency set), is unsafe.
However, since most devices do not validate if the low_latency
setting is appropriate for the context (process or interrupt) in
which they receive data, some reports are due to misconfiguration.
Further, serial dma devices for which dma fails, resort to
interrupt receiving as a backup without resetting low_latency.
Historically, low_latency was used to force wake-up the reading
process rather than wait for the next scheduler tick. The
effect was to trim multiple milliseconds of latency from
when the process would receive new data.
Recent tests [1] have shown that the reading process now receives
data with only 10's of microseconds latency without low_latency set.
Remove the low_latency rx steering from tty_flip_buffer_push();
however, leave the knob as an optional hint to drivers that can
tune their rx fifos and such like. Cleanup stale code comments
regarding low_latency.
[1] https://lkml.org/lkml/2014/2/20/434
"Yay.. thats an annoying historical pain in the butt gone."
-- Alan Cox
Reported-by: Beat Bolli <bbolli@ewanet.ch>
Reported-by: Pavel Roskin <proski@gnu.org>
Acked-by: David Sterba <dsterba@suse.cz>
Cc: Grant Edwards <grant.b.edwards@gmail.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Hal Murray <murray+fedora@ip-64-139-1-69.sjc.megapath.net>
Cc: <stable@vger.kernel.org> # 3.12.x+
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a matching table for the the bcm63xx_uart driver on the compatible
string "brcm,bcm6345-uart" which covers all BCM63xx implementations and
reflects the fact that this block was first introduced with the BCM6345
SoC. Also make sure that we convert the id based on the uart aliases
provided by the relevant Device Tree.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bcm63xx_uart driver uses RSET_UART_SIZE which is a constant defined
for MIPS-based BCM63xx platforms, pull this constant value from the
MIPS-specific header and put it in include/linux/serial_bcm63xx.h to
make the driver platform agnostic.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Include linux/io.h which provides the definition for
__raw_{readl,writel}, this is not necessary on MIPS since there is an
implicit inclusion, but it is on ARM for instance.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These can be used to send commands consisting of an arbitrary string to the
terminal, most often used to set a terminal's window title or to redefine
the colour palette. Our console doesn't use OSC, unlike everything else,
which can lead to junk being displayed if a process sends such a code
unconditionally.
The rules for termination follow established practice rather than Ecma-48.
Ecma-48 requires the string to use only byte values 0x08..0x0D and
0x20..0x7E, terminated with either ESC \ or 0x9C. This would disallow using
8-bit characters, which are reasonable for example in window titles.
A widespread idiom is to terminate with 0x07. The behaviour for other
control characters differs between terminal emulators, I followed libvte and
xterm:
* 0x07 and ESC anything terminate
* nothing else terminates, all 8-bit values including 0x9C are considered a
part of the string
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Every couple of months, someone sends a patch to fix:
drivers/tty/serial/8250/8250_core.c: In function 'serial_unlink_irq_chain':
drivers/tty/serial/8250/8250_core.c:1712:2: warning: 'i' may be used uninitialized in this function [-Wuninitialized]
and they in turn get a NACK for their efforts, and are told that
their compiler is broken. This has been going on since at least
the year 2008: https://lkml.org/lkml/2008/11/24/433
Lets add a comment, so that subsequent patches don't get as far as
the maintainers or the mailing lists.
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge "qcom driver changes for v3.15" from Kumar Gala:
We've split Qualcomm MSM support into legacy and multiplatform. These
drivers are only relevant on the multiplatform supported SoCs so switch the
Kconfig depends to ARCH_QCOM.
* tag 'qcom-drivers-for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom:
gpio: msm: switch Kconfig to ARCH_QCOM depends
hwrng: msm: switch Kconfig to ARCH_QCOM depends
power: reset: msm - switch Kconfig to ARCH_QCOM depends
drm/msm: drop ARCH_MSM Kconfig depend
tty: serial: msm: Enable building msm_serial for ARCH_QCOM
This reverts commit d8a5dc3033.
This breaks plymouth installs, either because plymouth is using the file
"incorrectly" or because the patch is incorrect. Either way, this needs
to be reverted until it is all figured out.
Reported-by: Josh Boyer <jwboyer@fedoraproject.org>
Reported-by: Ray Strode <halfline@gmail.com>
Cc: Lennart Poettering <lennart@poettering.net>
Cc: Kay Sievers <kay@vrfy.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Werner Fink <werner@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ARCH_MULTIPLATFORM. (For multi-platform code it's already unused since
387798b (ARM: initial multiplatform support).)
To make this work some code out of arch/arm needed to be adapted. The
respective changes got acks by their maintainers to be taken via armsoc
(with Andrew Morton substituting for Alessandro Zummo as rtc maintainer).
Compared to the previous pull request there was another patch added that
fixes a (non-critical) regression on ixp4xx. Olof Johansson asked to not
squash this fix into the original commit to save him from the need to
reverify the series.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABCAAGBQJTA8PeAAoJEOLc3ZEyZpvW5GEP/iz+HIx8Rkf3exUOorZB0Kef
dPC1Bmc4SThffhgmmXTjSapTzjfnuC8xq8dni008L7QR0LFJsC/rw8bR9GqYhTDs
EP7Sk0vDJcTUw9dvlIG0jpBioxdsPY7isU8K85tr2a+dzi4JA2h8iv6gE7bsOf1c
b18hIWp2ZZdeYQX3OcuzPeVfvXuMaayBJChq0akoW7zqxG2nHG9j1vCSOhBtrgpc
xCTuEqPoaDOdXjdhyda//3SKkIYh1eMf+RWMgW38vz2uHEI3AsMn/EWe6pNRKzRt
JdVC6LWFl5tl1Dz73NoGFQO+ztTBb2pTrmqggc+Hi4iTekJSmJSFU51D/E0hdJFj
KmWDWPLiUdAItjPuRz/HyeZxoIZQjg9PJ8MkjwVNAz4f4Vmw2xNnAV1Eur3k9JyV
fo55eaBvy2KIGzBB+/ksMUvs4HzMJ7Z/dVPzZYRF8VxlYFJXExT0O42oeJ8KsfH7
dJ1bjk+3VIWPLH3DHyyiIfBL1oxe4MemqrAREFnN2QxYHyCipXLwH35uNZXAqvcU
jverroWnCdrpOn9KI+vpnp/kuE7Qc1IH/AwAZngPj2xhaFapiH6h1JK/xWcWjijR
AKv1DhFJMqSp9fvclr/ZAb7o35V/LG0rpCs+oZumCCARwpxkbo8xXgG0CfPsYFrG
KwLWPz5zwySGwvDZ2wub
=g6PN
-----END PGP SIGNATURE-----
Merge tag 'dropmachtimexh-v2' of git://git.pengutronix.de/git/ukl/linux into next/cleanup
This cleanup series gets rid of <mach/timex.h> for platforms not using
ARCH_MULTIPLATFORM. (For multi-platform code it's already unused since
387798b (ARM: initial multiplatform support).)
To make this work some code out of arch/arm needed to be adapted. The
respective changes got acks by their maintainers to be taken via armsoc
(with Andrew Morton substituting for Alessandro Zummo as rtc maintainer).
Compared to the previous pull request there was another patch added that
fixes a (non-critical) regression on ixp4xx. Olof Johansson asked to not
squash this fix into the original commit to save him from the need to
reverify the series.
* tag 'dropmachtimexh-v2' of git://git.pengutronix.de/git/ukl/linux:
ARM: ixp4xx: fix timer latch calculation
ARM: drop <mach/timex.h> for !ARCH_MULTIPLATFORM, too
ARM: rpc: stop using <mach/timex.h>
ARM: ixp4xx: stop using <mach/timex.h>
input: ixp4xx-beeper: don't use symbols from <mach/timex.h>
ARM: at91: don't use <mach/timex.h>
ARM: ep93xx: stop using mach/timex.h
ARM: mmp: stop using mach/timex.h
ARM: netx: stop using mach/timex.h
ARM: sa1100: stop using mach/timex.h
clocksource: sirf/marco+prima2: drop usage of CLOCK_TICK_RATE
rtc: pxa: drop unused #define TIMER_FREQ
rtc: at91sam9: include <mach/hardware.h> explicitly
ARM/serial: at91: switch atmel serial to use gpiolib
Signed-off-by: Olof Johansson <olof@lixom.net>
Add dma support for lpuart. This function depend on DMA driver.
You can turn on it by write both the dmas and dma-name properties in dts node.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig symbol SVINTO_SIM got dropped in commit e269a86941 ("Drop
code for CRISv10 CPU simulator"). Now drop the remaining code for that
simulator.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a temporary solution to fix following issue:
config: make ARCH=alpha allyesconfig
All error/warnings:
drivers/tty/serial/max310x.c: In function 'max310x_ioctl':
>> drivers/tty/serial/max310x.c:905:7: error: 'TIOCSRS485' undeclared (first use in this function)
drivers/tty/serial/max310x.c:905:7: note: each undeclared identifier is reported only once for each function it appears in
>> drivers/tty/serial/max310x.c:906:3: error: implicit declaration of function 'copy_from_user' [-Werror=implicit-function-declaration]
>> drivers/tty/serial/max310x.c:929:7: error: 'TIOCGRS485' undeclared (first use in this function)
>> drivers/tty/serial/max310x.c:938:3: error: implicit declaration of function 'copy_to_user' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit e3c6ea9b1b as it
didn't help anything, and caused more problems than expected.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
\E[3J console code (secure clear screen) needs to update_screen(vc)
in order to write-through blanks into off-screen video memory.
This has been removed accidentally in 3.6 by:
commit 81732c3b2f
Author: Jean-François Moine <moinejf@free.fr>
Date: Thu Sep 6 19:24:13 2012 +0200
tty vt: Fix line garbage in virtual console on command line edition
Signed-off-by: Petr Písař <petr.pisar@atlas.cz>
Cc: stable <stable@vger.kernel.org> # 3.6
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 3e6c6f630a ("Delay creation of
khcvd thread") moved the call of hvc_init from being a device_initcall
into hvc_alloc, and used a non-null hvc_driver as indication of whether
hvc_init had already been called.
The problem with this is that hvc_driver is only assigned a value
at the bottom of hvc_init, and so there is a window where multiple
hvc_alloc calls can be in progress at the same time and hence try
and call hvc_init multiple times. Previously the use of device_init
guaranteed that hvc_init was only called once.
This manifests itself as sporadic instances of two hvc_init calls
racing each other, and with the loser of the race getting -EBUSY
from tty_register_driver() and hence that virtual console fails:
Couldn't register hvc console driver
virtio-ports vport0p1: error -16 allocating hvc for port
Here we add an atomic_t to guarantee we'll never run hvc_init twice.
Cc: stable@vger.kernel.org # v2.6.24+
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 3e6c6f630a ("Delay creation of khcvd thread")
Reported-by: Jim Somerville <Jim.Somerville@windriver.com>
Tested-by: Jim Somerville <Jim.Somerville@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
instead of using sirf specific dma channel property like "sirf,uart-dma-rx-channel"
and "sirf,uart-dma-tx-channel", here we move to use generic dma dt-binding to get
the channel like:
- sirf,uart-dma-rx-channel = <21>;
- sirf,uart-dma-tx-channel = <2>;
+ dmas = <&dmac1 5>, <&dmac0 2>;
+ dma-names = "rx", "tx";
and we move dma_request_channel() to dma_request_slave_channel(), we don't need to
call sirfsoc dma filter function sirfsoc_dma_filter_id() again.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_register_driver call binds the driver to a specific device
node through tty_register_driver call. This should typically happen
during device probe call.
In a multiplatform scenario, it is possible that multiple serial
drivers are part of the kernel. Currently the driver registration fails
if multiple serial drivers with same default major/minor numbers are
included in the kernel.
A typical case is observed with amba-pl011 and samsung-uart drivers.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_register_driver call binds the driver to a specific device
node through tty_register_driver call. This should typically happen
during device probe call.
In a multiplatform scenario, it is possible that multiple serial
drivers are part of the kernel. Currently the driver registration fails
if multiple serial drivers with same default major/minor numbers are
included in the kernel.
A typical case is observed with amba-pl011 and samsung-uart drivers.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
config: x86_64-randconfig-x006 (attached as .config)
All warnings:
drivers/tty/serial/max310x.c: In function 'max310x_probe':
>> drivers/tty/serial/max310x.c:1240:1: warning: label 'out_uart' defined but not used [-Wunused-label]
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
config: make ARCH=alpha allyesconfig
All error/warnings:
drivers/tty/serial/max310x.c: In function 'max310x_ioctl':
>> drivers/tty/serial/max310x.c:905:7: error: 'TIOCSRS485' undeclared (first use in this function)
drivers/tty/serial/max310x.c:905:7: note: each undeclared identifier is reported only once for each function it appears in
>> drivers/tty/serial/max310x.c:906:3: error: implicit declaration of function 'copy_from_user' [-Werror=implicit-function-declaration]
>> drivers/tty/serial/max310x.c:929:7: error: 'TIOCGRS485' undeclared (first use in this function)
>> drivers/tty/serial/max310x.c:938:3: error: implicit declaration of function 'copy_to_user' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current code only wakes up the processes when the circle
buffer has less data then the WAKEUP_CHARS.
But sometimes, the circle buffer may has data more then the WAKEUP_CHARS,
in such case, the processes will hang.
This patch makes it always wakes up the processes in the TX callback.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes a driver bug which stopped the whole system (in case
of serial console).
This log message is not useful anyway as this information is
printed elsewhere.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Exar XR17V35x family of UARTs have an additional fractional divisor
register (DLD) which was not being used. Calculate and set this
register for these devices to reduce their baud rate error.
Signed-off-by: Joe Schultz <jschultz@xes-inc.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When echoes cannot be flushed to output (usually because the tty
has no more write room) and L_ECHO is subsequently turned off, then
when L_ECHO is turned back on, stale echoes are output.
Output completed echoes regardless of the L_ECHO setting:
1. before normal writes to that tty
2. if the tty was stopped by soft flow control and is being
restarted
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: <stable@vger.kernel.org> # 3.13.x
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b9ade9f74 coming from Viresh Kumar "tty: serial: sirfsoc: drop
uart_port->lock before calling tty_flip_buffer_push()" broke sirfsoc uart
driver by knic:
[ 5.129122] BUG: spinlock already unlocked on CPU#0, ip6tables/1331
[ 5.132554] lock: sirfsoc_uart_ports+0x4/0x8a0, .magic: dead4ead,
.owner: <none>/-1, .owner_cpu: -1
[ 5.141651] CPU: 0 PID: 1331 Comm: ip6tables Tainted: G
W O 3.10.16 #3
[ 5.148866] [<c0013528>] (unwind_backtrace+0x0/0xe0) from
[<c0010e70>] (show_stack+0x10/0x14)
[ 5.157362] [<c0010e70>] (show_stack+0x10/0x14) from
[<c01a5e68>] (do_raw_spin_unlock+0x40/0xc8)
[ 5.166125] [<c01a5e68>] (do_raw_spin_unlock+0x40/0xc8) from
[<c03ff8b4>] (_raw_spin_unlock+0x8/0x40)
[ 5.175322] [<c03ff8b4>] (_raw_spin_unlock+0x8/0x40) from
[<c0203fcc>] (sirfsoc_uart_pio_rx_chars+0xa4/0xc0)
[ 5.185120] [<c0203fcc>]
(sirfsoc_uart_pio_rx_chars+0xa4/0xc0) from [<c0204fb8>]
(sirfsoc_rx_tmo_process_tl+0xdc/0x1e0)
[ 5.195875] [<c0204fb8>]
(sirfsoc_rx_tmo_process_tl+0xdc/0x1e0) from [<c0024b50>]
(tasklet_action+0x8c/0xec)
[ 5.205673] [<c0024b50>] (tasklet_action+0x8c/0xec) from
[<c00242a8>] (__do_softirq+0xec/0x1d4)
[ 5.214347] [<c00242a8>] (__do_softirq+0xec/0x1d4) from
[<c0024428>] (do_softirq+0x48/0x54)
[ 5.222674] [<c0024428>] (do_softirq+0x48/0x54) from
[<c0024690>] (irq_exit+0x74/0xc0)
[ 5.230573] [<c0024690>] (irq_exit+0x74/0xc0) from
[<c000e1e8>] (handle_IRQ+0x6c/0x90)
[ 5.238465] [<c000e1e8>] (handle_IRQ+0x6c/0x90) from
[<c000d500>] (__irq_svc+0x40/0x70)
[ 5.246446] [<c000d500>] (__irq_svc+0x40/0x70) from
[<c0092e7c>] (mark_page_accessed+0xc/0x68)
[ 5.255034] [<c0092e7c>] (mark_page_accessed+0xc/0x68) from
[<c00a2a4c>] (unmap_single_vma+0x3bc/0x550)
[ 5.264402] [<c00a2a4c>] (unmap_single_vma+0x3bc/0x550) from
[<c00a3b4c>] (unmap_vmas+0x44/0x54)
[ 5.273164] [<c00a3b4c>] (unmap_vmas+0x44/0x54) from
[<c00a81a8>] (exit_mmap+0xc4/0x1e0)
[ 5.281233] [<c00a81a8>] (exit_mmap+0xc4/0x1e0) from
[<c001bb78>] (mmput+0x3c/0xdc)
[ 5.288868] [<c001bb78>] (mmput+0x3c/0xdc) from [<c0021b0c>]
(do_exit+0x30c/0x828)
[ 5.296413] [<c0021b0c>] (do_exit+0x30c/0x828) from
[<c0022dac>] (do_group_exit+0x4c/0xb0)
[ 5.304653] [<c0022dac>] (do_group_exit+0x4c/0xb0) from
[<c0022e20>] (__wake_up_parent+0x0/0x18)
Root cause:
the commit dropped uart_port->lock before calling tty_flip_buffer_push(), but in sirfsoc-uart,
sirfsoc_uart_pio_rx_chars() can be called by sirfsoc_rx_tmo_process_tl(). here uart_port->lock
has not been taken yet. so that caused unpaired lock/unlock.
Solution:
This patch is doing a quick fix for that, it adds spin_lock/unlock(&port->lock) protect to
sirfsoc_uart_pio_rx_chars() in sirfsoc_rx_tmo_process_tl() to keep spin_lock/unlock in pair.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Cc: stable <stable@vger.kernel.org> # 3.12
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Aparently 9865 uses standard BAR encoding scheme (unlike 99xx cards).
Current pci_netmos_9900_setup() uses wrong BAR indices for the 9865 PCI
device, function 2. Using standard BAR indices makes all 6 ports work
for me. Thus disable the NetMos 9900 quirk for NetMos 9865 pci device.
For the reference, here is the relevant part of lspci for my device:
02:07.0 Serial controller: MosChip Semiconductor Technology Ltd. PCI
9865 Multi-I/O Controller (prog-if 02 [16550])
Subsystem: Device a000:1000
Flags: bus master, medium devsel, latency 32, IRQ 17
I/O ports at ac00 [size=8]
Memory at fcfff000 (32-bit, non-prefetchable) [size=4K]
Memory at fcffe000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [48] Power Management version 2
Kernel driver in use: serial
02:07.1 Serial controller: MosChip Semiconductor Technology Ltd. PCI
9865 Multi-I/O Controller (prog-if 02 [16550])
Subsystem: Device a000:1000
Flags: bus master, medium devsel, latency 32, IRQ 18
I/O ports at a800 [size=8]
Memory at fcffd000 (32-bit, non-prefetchable) [size=4K]
Memory at fcffc000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [48] Power Management version 2
Kernel driver in use: serial
02:07.2 Communication controller: MosChip Semiconductor Technology Ltd.
PCI 9865 Multi-I/O Controller
Subsystem: Device a000:3004
Flags: bus master, medium devsel, latency 32, IRQ 19
I/O ports at a400 [size=8]
I/O ports at a000 [size=8]
I/O ports at 9c00 [size=8]
I/O ports at 9800 [size=8]
Memory at fcffb000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [48] Power Management version 2
Kernel driver in use: serial
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit eafbe67f84,
n_tty: Refactor input_available_p() by call site
broke poll() when TIME_CHAR(tty) and MIN_CHAR(tty) are both 0.
When TIME_CHAR and MIN_CHAR are both 0, input is available if the
read_cnt is 1 (not 0).
Reported-by: Eric Dumazet <edumazet@google.com>
Tested-by: Eric Dumazet <edumazet@google.com>
Reported-by: Stephane Eranian <eranian@google.com>
Tested-by: David Ahern <dsahern@gmail.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the gpio is not yet available we better also
defer the probing in the rs485 case.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_PM will be set if either or both CONFIG_PM_SLEEP and
CONFIG_PM_RUNTIME is set. Compiling the driver with !CONFIG_PM_SLEEP causes
following compilation warnings:
drivers/tty/serial/8250/8250_dw.c:404:12: warning: ‘dw8250_suspend’ defined but not used [-Wunused-function]
drivers/tty/serial/8250/8250_dw.c:413:12: warning: ‘dw8250_resume’ defined but not used [-Wunused-function]
Fix this by using CONFIG_PM_SLEEP instead.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the info message about a missing wakeirq for uart is printed
every time the serial driver's startup function is called. This happens
multiple times and not just once.
This can cause lots of extra messages at boot time, slowing things down. It is
caused by commit 2a0b965cfb (serial: omap: Add support for optional wake-up)
which was applied for v3.13-rc1.
This patch moves the infomessage to the probe function to display it
only once.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: stable <stable@vger.kernel.org> # 3.13
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds devicetree support for the MAX310X serial driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes some unused definitions from driver code and
sort #includes alphabetically.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for RS-485 (TIOCSRS485/TIOCGRS485) IOCTLs.
As a result this patch eliminate private driver header.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Always register GPIOs and use dynamic GPIO ID assignment.
This is no much worth if GPIOs is not used, but helps remove
private driver header and add DT support in the future.
Additionally, patch adds missing uart_unregister_driver()
call if probe() fails.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes "frequency" parameter from MAX310X platform_data
and uses CLK API for getting clock. Clock type (XTAL/OSC) is
determined by clk name.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch move all SPI-dependent stuff in one place. This include move
PM-function definitions out of CONFIG_SPI_MASTER and move regmap
initialization out of common probe into CONFIG_SPI_MASTER which
may help to add I2C support in the future for this driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since 93abe8e4 (clk: add non CONFIG_HAVE_CLK routines) code using clk.h
like this driver needs not depend on HAVE_CLK.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes excess IRQ checks at driver probe().
IRQ validation is already provided by request_threaded_irq().
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replaces loopback mode support from platform data to
dynamic setup with TIOCMSET ioctl.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Serial core calls set_termios() after port startup, so there are
no reason to setup port twice.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These callbacks were previously used for the IC power initialization.
If this initialization will be needed in the future, it should be
implemented with the regulator API.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch provide more precisely setup of baud rate generator.
If the result of division has a remainder, we use the multiplier
for the base frequency. Additionally, we report result baud rate
back to serial core.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hardware supported by the driver is only found on SUPERH or
ARCH_SHMOBILE platforms. Restrict non-COMPILE_TEST compilation to them.
Cc: linux-serial@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add CONFIG_DEBUG_FS to 'char name' in order to fix the following
build warning, because 'char name' is used only when CONFIG_DEBUG_FS
is enabled.
drivers/tty/serial/pch_uart.c:1765:7: warning: unused variable 'name' [-Wunused-variable]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following compile warning about cast to pointer from
integer of different size.
drivers/tty/serial/sh-sci.c:2021:19: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the info message about a missing wakeirq for uart is printed
every time the serial driver's startup function is called. This happens
multiple times and not just once.
This patch moves the infomessage to the probe function to display it
only once.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement the polling functionality for the MSM serial driver.
This allows us to use KGDB on this hardware.
Cc: David Brown <davidb@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "int check" argument of lock_acquire() and held_lock->check are
misleading. This is actually a boolean: 2 means "true", everything
else is "false".
And there is no need to pass 1 or 0 to lock_acquire() depending on
CONFIG_PROVE_LOCKING, __lock_acquire() checks prove_locking at the
start and clears "check" if !CONFIG_PROVE_LOCKING.
Note: probably we can simply kill this member/arg. The only explicit
user of check => 0 is rcu_lock_acquire(), perhaps we can change it to
use lock_acquire(trylock =>, read => 2). __lockdep_no_validate means
check => 0 implicitly, but we can change validate_chain() to check
hlock->instance->key instead. Not to mention it would be nice to get
rid of lockdep_set_novalidate_class().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20140120182006.GA26495@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The 'active' sysfs attribute should refer to the currently active tty
devices the console is running on, not the currently active console.
The console structure doesn't refer to any device in sysfs, only the tty
the console is running on has. So we need to print out the tty names in
'active', not the console names.
This resolves an issue on s390 platforms in determining the correct
console device to use.
Cc: Lennart Poettering <lennart@poettering.net>
Cc: Kay Sievers <kay@vrfy.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Werner Fink <werner@suse.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
3GPP TS 07.10 states in section 5.4.6.3.7:
"The length byte contains the value 2 or 3 ... depending on the break
signal." The break byte is optional and if it is sent, the length is
3. In fact the driver was not able to work with modems that send this
break byte in their modem status control message. If the modem just
sends the break byte if it is really set, then weird things might
happen.
The code for deconding the modem status to the internal linux
presentation in gsm_process_modem has already a big comment about
this 2 or 3 byte length thing and it is already able to decode the
brk, but the code calling the gsm_process_modem function in
gsm_control_modem does not encode it and hand it over the right way.
This patch fixes this.
Without this fix if the modem sends the brk byte in it's modem status
control message the driver will hang when opening a muxed channel.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The HVC_OPAL/RTAS/UDBG/XEN options are all bool, and hence their support
is either present or absent. It will never be modular, so using
module_init as an alias for __initcall is rather misleading.
Fix this up now, so that we can relocate module_init from
init.h into module.h in the future. If we don't do this, we'd
have to add module.h to obviously non-modular code, and that
would be a worse thing.
Note that direct use of __initcall is discouraged, vs. one
of the priority categorized subgroups. As __initcall gets
mapped onto device_initcall, our use of device_initcall
directly in this change means that the runtime impact is
zero -- it will remain at level 6 in initcall ordering.
Also the __exitcall functions have been outright deleted since
they are only ever of interest to UML, and UML will never be
using any of this code.
Cc: Richard Weinberger <richard@nod.at>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We've split Qualcomm MSM support into legacy and multiplatform. So add
the ability to build the serial driver on the newer ARCH_QCOM
multiplatform.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Pull MIPS updates from Ralf Baechle:
"The most notable new addition inside this pull request is the support
for MIPS's latest and greatest core called "inter/proAptiv". The
patch series describes this core as follows.
"The interAptiv is a power-efficient multi-core microprocessor
for use in system-on-chip (SoC) applications. The interAptiv combines
a multi-threading pipeline with a coherence manager to deliver improved
computational throughput and power efficiency. The interAptiv can
contain one to four MIPS32R3 interAptiv cores, system level
coherence manager with L2 cache, optional coherent I/O port,
and optional floating point unit."
The platform specific patches touch all 3 Broadcom families. It adds
support for the new Broadcom/Netlogix XLP9xx Soc, building a common
BCM63XX SMP kernel for all BCM63XX SoCs regardless of core type/count
and full gpio button/led descriptions for BCM47xx.
The rest of the series are cleanups and bug fixes that are MIPS
generic and consist largely of changes that Imgtec/MIPS had published
in their linux-mti-3.10.git stable tree. Random other cleanups and
patches preparing code to be merged in 3.15"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (139 commits)
mips: select ARCH_MIGHT_HAVE_PC_SERIO
mips: delete non-required instances of include <linux/init.h>
MIPS: KVM: remove shadow_tlb code
MIPS: KVM: use common EHINV aware UNIQUE_ENTRYHI
mips/ide: flush dcache also if icache does not snoop dcache
MIPS: BCM47XX: fix position of cpu_wait disabling
MIPS: BCM63XX: select correct MIPS_L1_CACHE_SHIFT value
MIPS: update MIPS_L1_CACHE_SHIFT based on MIPS_L1_CACHE_SHIFT_<N>
MIPS: introduce MIPS_L1_CACHE_SHIFT_<N>
MIPS: ZBOOT: gather string functions into string.c
arch/mips/pci: don't check resource with devm_ioremap_resource
arch/mips/lantiq/xway: don't check resource with devm_ioremap_resource
bcma: gpio: don't cast u32 to unsigned long
ssb: gpio: add own IRQ domain
MIPS: BCM47XX: fix sparse warnings in board.c
MIPS: BCM47XX: add board detection for Linksys WRT54GS V1
MIPS: BCM47XX: fix detection for some boards
MIPS: BCM47XX: Enable buttons support on SSB
MIPS: BCM47XX: Convert WNDR4500 to new syntax
MIPS: BCM47XX: Use "timer" trigger for status LEDs
...
Pull more powerpc bits from Ben Herrenschmidt:
"Here are a few more powerpc bits for this merge window. The bulk is
made of two pull requests from Scott and Anatolij that I had missed
previously (they arrived while I was away). Since both their branches
are in -next independently, and the content has been around for a
little while, they can still go in.
The rest is mostly bug and regression fixes, a small series of
cleanups to our pseries cpuidle code (including moving it to the right
place), and one new cpuidle bakend for the powernv platform. I also
wired up the new sched_attr syscalls"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (37 commits)
powerpc: Wire up sched_setattr and sched_getattr syscalls
powerpc/hugetlb: Replace __get_cpu_var with get_cpu_var
powerpc: Make sure "cache" directory is removed when offlining cpu
powerpc/mm: Fix mmap errno when MAP_FIXED is set and mapping exceeds the allowed address space
powerpc/powernv/cpuidle: Back-end cpuidle driver for powernv platform.
powerpc/pseries/cpuidle: smt-snooze-delay cleanup.
powerpc/pseries/cpuidle: Remove MAX_IDLE_STATE macro.
powerpc/pseries/cpuidle: Make cpuidle-pseries backend driver a non-module.
powerpc/pseries/cpuidle: Use cpuidle_register() for initialisation.
powerpc/pseries/cpuidle: Move processor_idle.c to drivers/cpuidle.
powerpc: Fix 32-bit frames for signals delivered when transactional
powerpc/iommu: Fix initialisation of DART iommu table
powerpc/numa: Fix decimal permissions
powerpc/mm: Fix compile error of pgtable-ppc64.h
powerpc: Fix hw breakpoints on !HAVE_HW_BREAKPOINT configurations
clk: corenet: Adds the clock binding
powerpc/booke64: Guard e6500 tlb handler with CONFIG_PPC_FSL_BOOK3E
powerpc/512x: dts: add MPC5125 clock specs
powerpc/512x: clk: support MPC5121/5123/5125 SoC variants
powerpc/512x: clk: enforce even SDHC divider values
...
