STM32G0 comes with STM32 bootloader in its system memory. Add support
for some I2C bootloader commands as described in application notes
AN2606 and AN4221, to enable STM32G0 UCSI firmware update.
Upon probing, the driver needs to know the STM32G0 state:
- In bootloader mode, STM32 G0 answers at i2c addr 0x51.
- In running mode, STM32 G0 firmware may answer at two address.
- The main address specified in DT is used for UCSI.
- 0x51 addr can be re-used for FW controls like getting software version
or jump to booloader request.
So probe using the main firmware i2c address first, before attempting
bootloader address (e.g. check for blank, erased or previously aborted
firmware update).
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20220713120842.560902-4-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
STM32G0 provides an integrated USB Type-C and power delivery interface.
It can be programmed with a firmware to handle UCSI protocol over I2C
interface. A GPIO is used as an interrupt line.
Type-C connector can be used as a wakeup source (typically to detect
changes on the port, like attach or detach). PM suspend / resume routines
are used to enable wake irqs, and signal a wakeup event in case the IRQ
has fired while in suspend. The i2c core is doing the necessary
initialization when the "wakeup-source" flag is provided.
Note: the interrupt handler shouldn't be called before the i2c bus resumes.
So, the interrupts are disabled during suspend period, and re-enabled
upon resume, to avoid i2c transfer while suspended, from the irq handler.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20220713120842.560902-3-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We found PPM will not send any notification after it report error status
and OPM issue GET_ERROR_STATUS command to read the details about error.
According UCSI spec, PPM may clear the Error Status Data after the OPM
has acknowledged the command completion.
This change add operation to acknowledge the command completion from PPM.
Fixes: bdc62f2bae (usb: typec: ucsi: Simplified registration and I/O API)
Cc: <stable@vger.kernel.org> # 5.10
Signed-off-by: Jack Pham <quic_jackp@quicinc.com>
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Link: https://lore.kernel.org/r/1658817949-4632-1-git-send-email-quic_linyyuan@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fwnode_connection_find_match() function handles two cases: named
references and graph endpoints. In the second case, the match function
passed in is called with the id to check for the match. However, the
match function for the recently added type-c retimer class assumes the
connection has already been matched (which is only true for the first
case).
The result is that with that change, all type-c nodes with graph
endpoints defer probe indefinitely, independently of having a retimer
connection or not.
Add the missing check, like is done by the type-c mux and usb role
switch code, to fix the issue.
Fixes: ddaf8d96f9 ("usb: typec: Add support for retimers")
Reviewed-by: Prashant Malani <pmalani@chromium.org>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220725203129.1973260-1-nfraprado@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If i2c_new_dummy_device() fails, it never return NULL pointer, replace
NULL test with IS_ERR() to fix it.
Fixes: fe6d8a9c8e ("usb: typec: anx7411: Add Analogix PD ANX7411 support")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220721071201.269344-2-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It should be 'ctx->typec.amode[i]' passed to PTR_ERR() when
typec_partner_register_altmode() failed.
Fixes: fe6d8a9c8e ("usb: typec: anx7411: Add Analogix PD ANX7411 support")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220721071201.269344-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Semi colons and commas are equivalent in this context but semi-colons
are better style.
Reviewed-by: Xin Ji <xji@analogixsemi.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YtpD4MKBa43higNc@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a minor bug which means that certain error messages are not
printed.
The devm_gpiod_get_optional() function can return either error pointers
or NULL. It returns error pointers if there is an allocation failure,
or a similar issue. It returns NULL if no GPIO was assigned to the
requested function. Print an error in either case.
The gpiod_to_irq() function never returns zero. It either returns
a positive IRQ number or a negative error code.
Fixes: fe6d8a9c8e ("usb: typec: anx7411: Add Analogix PD ANX7411 support")
Reviewed-by: Xin Ji <xji@analogixsemi.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YtpDs8VsWIbl/Smd@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This should be ARRAY_SIZE() instead of sizeof(). ARRAY_SIZE is
4 and sizeof is 8.
Fixes: fe6d8a9c8e ("usb: typec: anx7411: Add Analogix PD ANX7411 support")
Reviewed-by: Xin Ji <xji@analogixsemi.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YtpC5s4/AD8vFz+X@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Similar to mux and orientation switch, add a handle for registered
retimer to the port, so that it has handles to the various switches
connected to it.
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220711072333.2064341-3-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce a retimer device class and associated functions that register
and use retimer "switch" devices. These operate in a manner similar to
the "mode-switch" and help configure retimers that exist between the
Type-C connector and host controller(s).
Type C ports can be linked to retimers using firmware node device
references (again, in a manner similar to "mode-switch").
There are no new sysfs files being created; there is the new retimer
class directory, but there are no class-specific files being created
there.
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220711072333.2064341-2-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add driver for analogix ANX7411 USB Type-C DRP port controller.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Xin Ji <xji@analogixsemi.com>
Link: https://lore.kernel.org/r/20220714081350.36447-2-xji@analogixsemi.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
System like Android allow user control power role from UI, it is possible
to implement application base on typec uevent to refresh UI, but found
there is chance that UI show different state from typec attribute file.
In typec_set_pwr_opmode(), when partner support PD, there is no uevent
send to user space which cause the problem.
Fix it by sending uevent notification when change power mode to PD.
Fixes: bdecb33af3 ("usb: typec: API for controlling USB Type-C Multiplexers")
Cc: stable@vger.kernel.org
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Link: https://lore.kernel.org/r/1656662934-10226-1-git-send-email-quic_linyyuan@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB PD controllers which consisting of a microcontroller (acting as the TCPM)
and a port controller (TCPC) - may require that the driver for the PD
controller accesses directly also the on-chip port controller in some cases.
Move tcpci.h to include/linux/usb/ is convenience access TCPC registers.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Xin Ji <xji@analogixsemi.com>
Link: https://lore.kernel.org/r/20220706083433.2415524-1-xji@analogixsemi.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFRBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmK4zgIeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGrI8H+MeIYPff1m9vh1rZ
u1eCCtw/A+NqJ5l0Cq3Zj090crMb8zVkxr5QrdPxxJuxAK8AI/XzOUQivnNayp6v
bvWcbj9e95ZoIQjbPakozo3KYnaHXMFfrq6JNdGIBJ5yt5pVHtJ3iZk25wUZEghD
8lxoz4Uiuo14ZbLnlLjbXr5OEVupOH1OoQPghkSoolD8JBe1coOIYbzzJ69HBwNg
kCUyD0CsFCBpy0P7yBnPNrvQGOt+NVz9FLfEbYFj+ydQjzw3NNw7tyKTahqp7ScN
BS5Ftt0kuHqOyWDO9OP6dG1kGmvIWQZkrEroz1TS4FfgrrPRr5r0N9+tGvr9+tpZ
1tjaBA==
=L7lN
-----END PGP SIGNATURE-----
Merge 5.19-rc4 into usb-next
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Loosen the typec_mux_match() requirements so that searches where an
alt mode is not specified, but the target mux device lists the
"mode-switch" property, return a success.
This is helpful in Type C port drivers which would like to get a pointer
to the mux switch associated with a Type C port, but don't want to
specify a particular alt mode.
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220615172129.1314056-2-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel SoC PMIC is a generic name for all PMICs that are used
on Intel platforms. In particular, INTEL_SOC_PMIC kernel configuration
option refers to Crystal Cove PMIC, which has never been a part
of any Intel Broxton hardware. Drop wrong dependency from Kconfig.
Note, the correct dependency is satisfied via ACPI PMIC OpRegion driver,
which the Type-C depends on.
Fixes: d2061f9cc3 ("usb: typec: add driver for Intel Whiskey Cove PMIC USB Type-C PHY")
Reported-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220620104316.57592-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Register both the port and partner USB Power Delivery
Capabilities so they are exposed to the user space.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220502132058.86236-4-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All the USB Type-C Connector Class devices are protected, so
the drivers can not directly access them. This will adds a
few helpers that can be used to link the ports and partners
to the correct USB Power Delivery objects.
For ports a new optional sysfs attribute file is also added
that can be used to select the USB Power Delivery
capabilities that the port will advertise to the partner.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220502132058.86236-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introducing a small device class for USB Power Delivery.
The idea with it is that we do not mix any more USB Power
Delivery information into the USB Type-C connectors only.
This separation will make it possible to register USB Power
Delivery devices also from other places, for example from
USB Type-C Bridges (see USB Type-C Bridge Specification).
The device class will not always deal with only the messages
and objects that were negotiated with the partner, but
instead messages and objects that can be used in the
negotiation. That allows the USB PD devices to be shared and
reconfigured. The ports can decide which objects are to be
advertised to the partner before the contract is negotiated.
It is also possible to allow the user space to make that
decision if needed.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220502132058.86236-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of the AMD platforms have Cypress CCGX PD controller connected
to system I2C i.e designware I2C controller. Added support to enumerate
the CCGX client by adding ACPI ID to the firmware.
Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Link: https://lore.kernel.org/r/20220526063305.3144352-3-Sanket.Goswami@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implementation supports only Level trigger with ACTIVE HIGH,
which is overriding level and polarity set by the ACPI table, hence
implement the common utility function to manage irq requests.
Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Link: https://lore.kernel.org/r/20220526063305.3144352-2-Sanket.Goswami@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Spelling mistake (triple letters) in comment.
Detected with the help of Coccinelle.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Link: https://lore.kernel.org/r/20220521111145.81697-52-Julia.Lawall@inria.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the large set of char, misc, and other driver subsystem updates
for 5.19-rc1. The merge request for this has been delayed as I wanted
to get lots of linux-next testing due to some late arrivals of changes
for the habannalabs driver.
Highlights of this merge are:
- habanalabs driver updates for new hardware types and fixes and
other updates
- IIO driver tree merge which includes loads of new IIO drivers
and cleanups and additions
- PHY driver tree merge with new drivers and small updates to
existing ones
- interconnect driver tree merge with fixes and updates
- soundwire driver tree merge with some small fixes
- coresight driver tree merge with small fixes and updates
- mhi bus driver tree merge with lots of updates and new device
support
- firmware driver updates
- fpga driver updates
- lkdtm driver updates (with a merge conflict, more on that
below)
- extcon driver tree merge with small updates
- lots of other tiny driver updates and fixes and cleanups, full
details in the shortlog.
All of these have been in linux-next for almost 2 weeks with no reported
problems.
Note, there are 3 merge conflicts when merging this with your tree:
- MAINTAINERS, should be easy to resolve
- drivers/slimbus/qcom-ctrl.c, should be straightforward
resolution
- drivers/misc/lkdtm/stackleak.c, not an easy resolution. This
has been noted in the linux-next tree for a while, and
resolved there, here's a link to the resolution that Stephen
came up with and that Kees says is correct:
https://lore.kernel.org/r/20220509185344.3fe1a354@canb.auug.org.au
I will be glad to provide a merge point that contains these resolutions
if that makes things any easier for you.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYpnkbA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylOrgCggbbAFwESBY9o2YfpG+2VOLpc0GAAoJgY1XN8
P/gumbLEpFvoBZ5xLIW8
=KCgk
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc / other smaller driver subsystem updates from Greg KH:
"Here is the large set of char, misc, and other driver subsystem
updates for 5.19-rc1. The merge request for this has been delayed as I
wanted to get lots of linux-next testing due to some late arrivals of
changes for the habannalabs driver.
Highlights of this merge are:
- habanalabs driver updates for new hardware types and fixes and
other updates
- IIO driver tree merge which includes loads of new IIO drivers and
cleanups and additions
- PHY driver tree merge with new drivers and small updates to
existing ones
- interconnect driver tree merge with fixes and updates
- soundwire driver tree merge with some small fixes
- coresight driver tree merge with small fixes and updates
- mhi bus driver tree merge with lots of updates and new device
support
- firmware driver updates
- fpga driver updates
- lkdtm driver updates (with a merge conflict, more on that below)
- extcon driver tree merge with small updates
- lots of other tiny driver updates and fixes and cleanups, full
details in the shortlog.
All of these have been in linux-next for almost 2 weeks with no
reported problems"
* tag 'char-misc-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (387 commits)
habanalabs: use separate structure info for each error collect data
habanalabs: fix missing handle shift during mmap
habanalabs: remove hdev from hl_ctx_get args
habanalabs: do MMU prefetch as deferred work
habanalabs: order memory manager messages
habanalabs: return -EFAULT on copy_to_user error
habanalabs: use NULL for eventfd
habanalabs: update firmware header
habanalabs: add support for notification via eventfd
habanalabs: add topic to memory manager buffer
habanalabs: handle race in driver fini
habanalabs: add device memory scrub ability through debugfs
habanalabs: use unified memory manager for CB flow
habanalabs: unified memory manager new code for CB flow
habanalabs/gaudi: set arbitration timeout to a high value
habanalabs: add put by handle method to memory manager
habanalabs: hide memory manager page shift
habanalabs: Add separate poll interval value for protocol
habanalabs: use get_task_pid() to take PID
habanalabs: add prefetch flag to the MAP operation
...
Here is the "big" set of USB and Thunderbolt driver changes for
5.18-rc1. For the most part it's been a quiet development cycle for the
USB core, but there are the usual "hot spots" of development activity.
Included in here are:
- Thunderbolt driver updates:
- fixes for devices without displayport adapters
- lane bonding support and improvements
- other minor changes based on device testing
- dwc3 gadget driver changes. It seems this driver will never
be finished given that the IP core is showing up in zillions
of new devices and each implementation decides to do something
different with it...
- uvc gadget driver updates as more devices start to use and
rely on this hardware as well
- usb_maxpacket() api changes to remove an unneeded and unused
parameter.
- usb-serial driver device id updates and small cleanups
- typec cleanups and fixes based on device testing
- device tree updates for usb properties
- lots of other small fixes and driver updates.
All of these have been in linux-next for weeks with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYpnZGw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymQhwCeLVANsQjBcL4ys4skl+1In17y28gAn3rEZ7rQ
Yv4uP9zadUqg3Cx0vjgf
=3s5s
-----END PGP SIGNATURE-----
Merge tag 'usb-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the "big" set of USB and Thunderbolt driver changes for
5.18-rc1. For the most part it's been a quiet development cycle for
the USB core, but there are the usual "hot spots" of development
activity.
Included in here are:
- Thunderbolt driver updates:
- fixes for devices without displayport adapters
- lane bonding support and improvements
- other minor changes based on device testing
- dwc3 gadget driver changes.
It seems this driver will never be finished given that the IP core
is showing up in zillions of new devices and each implementation
decides to do something different with it...
- uvc gadget driver updates as more devices start to use and rely on
this hardware as well
- usb_maxpacket() api changes to remove an unneeded and unused
parameter.
- usb-serial driver device id updates and small cleanups
- typec cleanups and fixes based on device testing
- device tree updates for usb properties
- lots of other small fixes and driver updates.
All of these have been in linux-next for weeks with no reported
problems"
* tag 'usb-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (154 commits)
USB: new quirk for Dell Gen 2 devices
usb: dwc3: core: Add error log when core soft reset failed
usb: dwc3: gadget: Move null pinter check to proper place
usb: hub: Simplify error and success path in port_over_current_notify
usb: cdns3: allocate TX FIFO size according to composite EP number
usb: dwc3: Fix ep0 handling when getting reset while doing control transfer
usb: Probe EHCI, OHCI controllers asynchronously
usb: isp1760: Fix out-of-bounds array access
xhci: Don't defer primary roothub registration if there is only one roothub
USB: serial: option: add Quectel BG95 modem
USB: serial: pl2303: fix type detection for odd device
xhci: Allow host runtime PM as default for Intel Alder Lake N xHCI
xhci: Remove quirk for over 10 year old evaluation hardware
xhci: prevent U2 link power state if Intel tier policy prevented U1
xhci: use generic command timer for stop endpoint commands.
usb: host: xhci-plat: omit shared hcd if either root hub has no ports
usb: host: xhci-plat: prepare operation w/o shared hcd
usb: host: xhci-plat: create shared hcd after having added main hcd
xhci: prepare for operation w/o shared hcd
xhci: factor out parts of xhci_gen_setup()
...
Merge general ACPI cleanups and processor support updates for 5.19-rc1:
- Rearrange find_child_checks() to simplify code (Rafael Wysocki).
- Use memremap() to map the UCSI mailbox that is always in main memory
and drop acpi_release_memory() that has no more users (Heikki
Krogerus, Dan Carpenter).
- Make max_cstate/nocst/bm_check_disable processor module parameters
visible in sysfs (Yajun Deng).
- Fix typo in the CPPC driver (Julia Lawall).
* acpi-glue:
ACPI: glue: Rearrange find_child_checks()
* acpi-osl:
usb: typec: ucsi: acpi: fix a NULL vs IS_ERR() check in probe
ACPI: OSL: Remove the helper for deactivating memory region
usb: typec: ucsi: acpi: Map the mailbox with memremap()
* acpi-processor:
ACPI: processor: idle: Expose max_cstate/nocst/bm_check_disable read-only in sysfs
* acpi-cppc:
ACPI: CPPC: fix typo in comment
The devm_memremap() function never returns NULL. It returns error
pointers.
Fixes: cdc3d2abf4 ("usb: typec: ucsi: acpi: Map the mailbox with memremap()")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The extcon_get_extcon_dev() function returns error pointers on error,
NULL when it's a -EPROBE_DEFER defer situation, and ERR_PTR(-ENODEV)
when the CONFIG_EXTCON option is disabled. This is very complicated for
the callers to handle and a number of them had bugs that would lead to
an Oops.
In real life, there are two things which prevented crashes. First,
error pointers would only be returned if there was bug in the caller
where they passed a NULL "extcon_name" and none of them do that.
Second, only two out of the eight drivers will build when CONFIG_EXTCON
is disabled.
The normal way to write this would be to return -EPROBE_DEFER directly
when appropriate and return NULL when CONFIG_EXTCON is disabled. Then
the error handling is simple and just looks like:
dev->edev = extcon_get_extcon_dev(acpi_dev_name(adev));
if (IS_ERR(dev->edev))
return PTR_ERR(dev->edev);
For the two drivers which can build with CONFIG_EXTCON disabled, then
extcon_get_extcon_dev() will now return NULL which is not treated as an
error and the probe will continue successfully. Those two drivers are
"typec_fusb302" and "max8997-battery". In the original code, the
typec_fusb302 driver had an 800ms hang in tcpm_get_current_limit() but
now that function is a no-op. For the max8997-battery driver everything
should continue working as is.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Returning an error value in an i2c remove callback results in an error
message being emitted by the i2c core, but otherwise it doesn't make a
difference. The device goes away anyhow and the devm cleanups are
called.
In this case the remove callback even returns early without stopping the
tcpm worker thread and various timers. A work scheduled on the work
queue, or a firing timer after tcpci_remove() returned probably results
in a use-after-free situation because the regmap and driver data were
freed. So better make sure that tcpci_unregister_port() is called even
if disabling the irq failed.
Also emit a more specific error message instead of the i2c core's
"remove failed (EIO), will be ignored" and return 0 to suppress the
core's warning.
This patch is (also) a preparation for making i2c remove callbacks
return void.
Fixes: 3ba76256fc ("usb: typec: tcpci: mask event interrupts when remove driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220502080456.21568-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmJu9FYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGAyEH/16xtJSpLmLwrQzG
o+4ToQxSQ+/9UHyu0RTEvHg2THm9/8emtIuYyc/5FgdoWctcSa3AaDcveWmuWmkS
KYcdhfJsaEqjNHS3OPYXN84fmo9Hel7263shu5+IYmP/sN0DfQp6UWTryX1q4B3Q
4Pdutkuq63Uwd8nBZ5LXQBumaBrmkkuMgWEdT4+6FOo1mPzwdIGBxCuz1UsNNl5k
chLWxkQfe2eqgWbYJrgCQfrVdORXVtoU2fGilZUNrHRVGkkldXkkz5clJfapyZD3
odmZCEbrE4GPKgZwCmDERMfD1hzhZDtYKiHfOQ506szH5ykJjPBcOjHed7dA60eB
J3+wdek=
=39Ca
-----END PGP SIGNATURE-----
Merge 5.18-rc5 into usb-next
We need the USB fixes in here, and this resolves a merge issue in
drivers/usb/dwc3/drd.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UCSI mailbox is always in main memory.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ON Semiconductor FSA4480 is a USB Type-C port multimedia switch with
support for analog audio headsets. It allows sharing a common USB Type-C
port to pass USB2.0 signal, analog audio, sideband use wires and analog
microphone signal.
Due to lacking upstream audio support for testing, the audio muxing is
left untouched, but implementation of muxing the SBU lines is provided
as a pair of Type-C mux and switch devices. This provides the necessary
support for enabling the DisplayPort altmode on devices with this
circuit.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220422222351.1297276-8-bjorn.andersson@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the Qualcomm platforms the USB/DP PHY handles muxing and orientation
switching of the SuperSpeed lines, but the SBU lines needs to be
connected and switched by external (to the SoC) hardware.
It's therefor necessary to be able to have the TypeC controller operate
multiple TypeC muxes and switches. Use the newly introduced indirection
object to handle this, to avoid having to taint the TypeC controllers
with knowledge about the downstream hardware configuration.
The max number of devs per indirection is set to 3, which account for
being able to mux/switch the USB HS, SS and SBU lines, as per defined
defined in the usb-c-connector binding. This number could be grown if
need arrises at a later point in time.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220422222351.1297276-6-bjorn.andersson@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rather than directly exposing the implementation's representation of the
typec muxes to the controller/clients, introduce an indirection object.
This enables the introduction of turning this relationship into a
one-to-many in the following patch.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220422222351.1297276-5-bjorn.andersson@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's possible that dev_set_name() returns -ENOMEM, catch and handle this.
Fixes: 3370db3519 ("usb: typec: Registering real device entries for the muxes")
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220422222351.1297276-4-bjorn.andersson@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When role switch module probe late than ucsi module,
fwnode_usb_role_switch_get() will return -EPROBE_DEFER,
it is better to restart ucsi init work to find
it again every 100ms, total wait time is 10 second.
It also means change ucsi init work to delayed_work.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Link: https://lore.kernel.org/r/1650881886-25530-3-git-send-email-quic_linyyuan@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In error path of ucsi_init(), it will unregister all valid ucsi connectors,
and similar operation also happen in ucsi_unregister(),
add a common function ucsi_unregister_connectors() for two places,
inside this function, if con->wq is NULL, it will break the loop,
if other kind of error happen after con->wq allocated,
ucsi/typec related API is safe to unregister.
Also in ucsi_init(), it allocate number of (ucsi->cap.num_connectors + 1)
connectors, there is one extra as the ending,
ucsi_unregister_connectors() is safe to unregister all ucsi connectors
according ucsi->cap.num_connectors,
remove the extra one connector to save memory.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Link: https://lore.kernel.org/r/1650881886-25530-2-git-send-email-quic_linyyuan@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Building without CONFIG_POWER_SUPPLY will fail:
drivers/usb/typec/rt1719.o: In function `rt1719_psy_set_property':
rt1719.c:(.text+0x10a): undefined reference to `power_supply_get_drvdata'
drivers/usb/typec/rt1719.o: In function `rt1719_psy_get_property':
rt1719.c:(.text+0x2c8): undefined reference to `power_supply_get_drvdata'
drivers/usb/typec/rt1719.o: In function `devm_rt1719_psy_register':
rt1719.c:(.text+0x3e9): undefined reference to `devm_power_supply_register'
drivers/usb/typec/rt1719.o: In function `rt1719_irq_handler':
rt1719.c:(.text+0xf9f): undefined reference to `power_supply_changed'
drivers/usb/typec/rt1719.o: In function `rt1719_update_pwr_opmode.part.9':
rt1719.c:(.text+0x657): undefined reference to `power_supply_changed'
drivers/usb/typec/rt1719.o: In function `rt1719_attach':
rt1719.c:(.text+0x83e): undefined reference to `power_supply_changed'
Add POWER_SUPPLY dependency to Kconfig.
Fixes: 25d29b9809 ("usb: typec: rt1719: Add support for Richtek RT1719")
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: ChiYuan Huang <cy_huang@richtek.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Ren Zhijie <renzhijie2@huawei.com>
Link: https://lore.kernel.org/r/20220418082425.41566-1-renzhijie2@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of refetching power status cache it and only update it when a
change is signalled via irq. This simplifies tracing and adding more
supply properties in follow up patches.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220317154518.4082046-2-sebastian.krzyszkowiak@puri.sm
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are few scenerio when PMC reports 'busy condition' and command
fail.
If PMC receives a high priority command while servicing a low priority
command then it discards the low priority command and start servicing
the high priority command. The lower priority command fail and driver
returns error. If the same command resend to the PMC then PMC latches
the command and service it accordingly.
Thus adds the retry logic for the PMC command.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Tanveer Alam <tanveer1.alam@intel.com>
Link: https://lore.kernel.org/r/20220328105137.6223-1-tanveer1.alam@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of USB and Thunderbolt changes for 5.18-rc1.
Nothing major in here, just lots of little improvements and cleanups and
new device support. Highlights are:
- list iterator fixups for when we walk past the end of the list
(a common problem that was cut/pasted in almost all USB gadget
drivers)
- xen USB driver "hardening" for malicious hosts
- xhci driver updates and fixes for more hardware types
- xhci debug cable fixes to make it actually work again
- usb gadget audio driver improvements
- usb gadget storage fixes to work with OS-X
- lots of other small usb gadget fixes and updates
- USB DWC3 driver improvements for more hardware types
- Lots of other small USB driver improvements
- DTS updates for some USB platforms
Note, the DTS updates will have a merge conflict in your tree. The
fixup should be simple, but if not, I can provide a merged tree if
needed.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYj7qpQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylRsQCcCryYifAvE2gHaNfI4B01JRWk7gQAoLNiUgvl
l+srEAXgIVueDhmDxy5P
=/Ppv
-----END PGP SIGNATURE-----
Merge tag 'usb-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt changes for 5.18-rc1.
Nothing major in here, just lots of little improvements and cleanups
and new device support. Highlights are:
- list iterator fixups for when we walk past the end of the list (a
common problem that was cut/pasted in almost all USB gadget
drivers)
- xen USB driver "hardening" for malicious hosts
- xhci driver updates and fixes for more hardware types
- xhci debug cable fixes to make it actually work again
- usb gadget audio driver improvements
- usb gadget storage fixes to work with OS-X
- lots of other small usb gadget fixes and updates
- USB DWC3 driver improvements for more hardware types
- Lots of other small USB driver improvements
- DTS updates for some USB platforms
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (172 commits)
usb: gadget: fsl_qe_udc: Add missing semicolon in qe_ep_dequeue()
dt-bindings: usb: mtk-xhci: add compatible for mt8186
usb: dwc3: Issue core soft reset before enabling run/stop
usb: gadget: Makefile: remove ccflags-y
USB: usb-storage: Fix use of bitfields for hardware data in ene_ub6250.c
usb: gadget: eliminate anonymous module_init & module_exit
usb: usbip: eliminate anonymous module_init & module_exit
xen/usb: harden xen_hcd against malicious backends
usb: dwc3: gadget: Wait for ep0 xfers to complete during dequeue
usb: dwc3: gadget: move cmd_endtransfer to extra function
usb: dwc3: gadget: ep_queue simplify isoc start condition
xen/usb: don't use arbitrary_virt_to_machine()
usb: isp1760: remove redundant max_packet() macro
usb: oxu210hp-hcd: remove redundant call to max_packet() macro
usb: common: usb-conn-gpio: Make VBUS supply completely optional
USB: storage: ums-realtek: fix error code in rts51x_read_mem()
usb: early: xhci-dbc: Fix xdbc number parsing
usb: early: xhci-dbc: Remove duplicate keep parsing
x86/tsc: Be consistent about use_tsc_delay()
usb: gadget: udc: s3c2410: remove usage of list iterator past the loop body
...
In order to bring up the USB3 PHY on the Apple M1 we need to know the
orientation of the Type-C cable. Extract it from the status register and
forward it to the typec subsystem.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Link: https://lore.kernel.org/r/20220226125912.59828-1-sven@svenpeter.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to avoid exposing acpi_bus_type to modules, introduce an
acpi_bus_for_each_dev() helper for iterating over all ACPI device
objects and make typec_link_ports() use it instead of the raw
bus_for_each_dev() along with acpi_bus_type.
Having done that, drop the acpi_bus_type export.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
