If we're using the default implementation of kgdb_roundup_cpus() that
uses smp_call_function_single_async() we can end up hanging
kgdb_roundup_cpus() if we try to round up a CPU that failed to round
up before.
Specifically smp_call_function_single_async() will try to wait on the
csd lock for the CPU that we're trying to round up. If the previous
round up never finished then that lock could still be held and we'll
just sit there hanging.
There's not a lot of use trying to round up a CPU that failed to round
up before. Let's keep a flag that indicates whether the CPU started
but didn't finish to round up before. If we see that flag set then
we'll skip the next round up.
In general we have a few goals here:
- We never want to end up calling smp_call_function_single_async()
when the csd is still locked. This is accomplished because
flush_smp_call_function_queue() unlocks the csd _before_ invoking
the callback. That means that when kgdb_nmicallback() runs we know
for sure the the csd is no longer locked. Thus when we set
"rounding_up = false" we know for sure that the csd is unlocked.
- If there are no timeouts rounding up we should never skip a round
up.
NOTE #1: In general trying to continue running after failing to round
up CPUs doesn't appear to be supported in the debugger. When I
simulate this I find that kdb reports "Catastrophic error detected"
when I try to continue. I can overrule and continue anyway, but it
should be noted that we may be entering the land of dragons here.
Possibly the "Catastrophic error detected" was added _because_ of the
future failure to round up, but even so this is an area of the code
that hasn't been strongly tested.
NOTE #2: I did a bit of testing before and after this change. I
introduced a 10 second hang in the kernel while holding a spinlock
that I could invoke on a certain CPU with 'taskset -c 3 cat /sys/...".
Before this change if I did:
- Invoke hang
- Enter debugger
- g (which warns about Catastrophic error, g again to go anyway)
- g
- Enter debugger
...I'd hang the rest of the 10 seconds without getting a debugger
prompt. After this change I end up in the debugger the 2nd time after
only 1 second with the standard warning about 'Timed out waiting for
secondary CPUs.'
I'll also note that once the CPU finished waiting I could actually
debug it (aka "btc" worked)
I won't promise that everything works perfectly if the errant CPU
comes back at just the wrong time (like as we're entering or exiting
the debugger) but it certainly seems like an improvement.
NOTE #3: setting 'kgdb_info[cpu].rounding_up = false' is in
kgdb_nmicallback() instead of kgdb_call_nmi_hook() because some
implementations override kgdb_call_nmi_hook(). It shouldn't hurt to
have it in kgdb_nmicallback() in any case.
NOTE #4: this logic is really only needed because there is no API call
like "smp_try_call_function_single_async()" or "smp_csd_is_locked()".
If such an API existed then we'd use it instead, but it seemed a bit
much to add an API like this just for kgdb.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Some code added to the debug_core module had KDB dependencies
that it shouldn't have. Move the KDB dependent REASON back to
the caller to remove the dependency in the debug core code.
Update the call from the UV NMI handler to conform to the new
interface.
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Hedi Berriche <hedi@sgi.com>
Cc: Russ Anderson <rja@sgi.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Link: http://lkml.kernel.org/r/20140114162551.318251993@asylum.americas.sgi.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch adds a kgdb_nmicallin() interface that can be used by
external NMI handlers to call the KGDB/KDB handler. The primary
need for this is for those types of NMI interrupts where all the
CPUs have already received the NMI signal. Therefore no
send_IPI(NMI) is required, and in fact it will cause a 2nd
unhandled NMI to occur. This generates the "Dazed and Confuzed"
messages.
Since all the CPUs are getting the NMI at roughly the same time,
it's not guaranteed that the first CPU that hits the NMI handler
will manage to enter KGDB and set the dbg_master_lock before the
slaves start entering. The new argument "send_ready" was added
for KGDB to signal the NMI handler to release the slave CPUs for
entry into KGDB.
Signed-off-by: Mike Travis <travis@sgi.com>
Acked-by: Jason Wessel <jason.wessel@windriver.com>
Reviewed-by: Dimitri Sivanich <sivanich@sgi.com>
Reviewed-by: Hedi Berriche <hedi@sgi.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Link: http://lkml.kernel.org/r/20131002151417.928886849@asylum.americas.sgi.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Although invasive kdb commands are not supported via kgdb, some useful
non-invasive commands like bt* require basic kdb state to be setup before
calling into the kdb code. Factor out some of this code and call it before
and after executing kdb commands via kgdb.
Signed-off-by: Matt Klein <mklein@twitter.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
For quite some time there have been problems with memory barriers and
various races with NMI on multi processor systems using the kernel
debugger. The algorithm for entering the kernel debug core and
resuming kernel execution was racy and had several known edge case
problems with attempting to debug something on a heavily loaded system
using breakpoints that are hit repeatedly and quickly.
The prior "locking" design entry worked as follows:
* The atomic counter kgdb_active was used with atomic exchange in
order to elect a master cpu out of all the cpus that may have
taken a debug exception.
* The master cpu increments all elements of passive_cpu_wait[].
* The master cpu issues the round up cpus message.
* Each "slave cpu" that enters the debug core increments its own
element in cpu_in_kgdb[].
* Each "slave cpu" spins on passive_cpu_wait[] until it becomes 0.
* The master cpu debugs the system.
The new scheme removes the two arrays of atomic counters and replaces
them with 2 single counters. One counter is used to count the number
of cpus waiting to become a master cpu (because one or more hit an
exception). The second counter is use to indicate how many cpus have
entered as slave cpus.
The new entry logic works as follows:
* One or more cpus enters via kgdb_handle_exception() and increments
the masters_in_kgdb. Each cpu attempts to get the spin lock called
dbg_master_lock.
* The master cpu sets kgdb_active to the current cpu.
* The master cpu takes the spinlock dbg_slave_lock.
* The master cpu asks to round up all the other cpus.
* Each slave cpu that is not already in kgdb_handle_exception()
will enter and increment slaves_in_kgdb. Each slave will now spin
try_locking on dbg_slave_lock.
* The master cpu waits for the sum of masters_in_kgdb and slaves_in_kgdb
to be equal to the sum of the online cpus.
* The master cpu debugs the system.
In the new design the kgdb_active can only be changed while holding
dbg_master_lock. Stress testing has not turned up any further
entry/exit races that existed in the prior locking design. The prior
locking design suffered from atomic variables not being truly atomic
(in the capacity as used by kgdb) along with memory barrier races.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Dongdong Deng <dongdong.deng@windriver.com>
One of the driving forces behind integrating another front end (kdb)
to the debug core is to allow front end commands to be accessible via
gdb's monitor command. It is true that you could write gdb macros to
get certain data, but you may want to just use gdb to access the
commands that are available in the kdb front end.
This patch implements the Rcmd gdb stub packet. In gdb you access
this with the "monitor" command. For instance you could type "monitor
help", "monitor lsmod" or "monitor ps A" etc...
There is no error checking or command restrictions on what you can and
cannot access at this point. Doing something like trying to set
breakpoints with the monitor command is going to cause nothing but
problems. Perhaps in the future only the commands that are actually
known to work with the gdb monitor command will be available.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
These are the minimum changes to the kgdb core in order to enable an
API to connect a new front end (kdb) to the debug core.
This patch introduces the dbg_kdb_mode variable controls where the
user level I/O is routed. It will be routed to the gdbstub (kgdb) or
to the kdb front end which is a simple shell available over the kgdboc
connection.
You can switch back and forth between kdb or the gdb stub mode of
operation dynamically. From gdb stub mode you can blindly type
"$3#33", or from the kdb mode you can enter "kgdb" to switch to the
gdb stub.
The logic in the debug core depends on kdb to look for the typical gdb
connection sequences and return immediately with KGDB_PASS_EVENT if a
gdb serial command sequence is detected. That should allow a
reasonably seamless transition between kdb -> gdb without leaving the
kernel exception state. The two gdb serial queries that kdb is
responsible for detecting are the "?" and "qSupported" packets.
CC: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Martin Hicks <mort@sgi.com>
Split the former kernel/kgdb.c into debug_core.c which contains the
kernel debugger exception logic and to the gdbstub.c which contains
the logic for allowing gdb to talk to the debug core.
This also created a private include file called debug_core.h which
contains all the definitions to glue the debug_core to any other
debugger connections.
CC: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
