The htmldoc produces this warning which was introduced
bu the commit below.
include/net/cfg80211.h:6643: warning: expecting prototype for wiphy_rfkill_set_hw_state().
Prototype was for wiphy_rfkill_set_hw_state_reason() instead
Fixes: 6f779a66dc ("cfg80211: allow specifying a reason for hw_rfkill")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://lore.kernel.org/r/20210413113850.59098-1-emmanuel.grumbach@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some HW/driver can support passing ethernet rx decap frames and
raw 802.11 frames for the monitor interface concurrently and
via separate RX calls to mac80211. Packets going to the monitor
interface(s) would be in 802.11 format and thus not have the
RX_FLAG_8023 set, and 802.11 format monitoring frames should have
RX_FLAG_ONLY_MONITOR set.
Drivers doing such can enable the SUPPORTS_CONC_MON_RX_DECAP to
allow using ethernet decap offload while a monitor interface is
active, currently RX decapsulation offload gets disabled when a
monitor interface is added.
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Link: https://lore.kernel.org/r/1617068116-32253-1-git-send-email-srirrama@codeaurora.org
[add proper documentation, rewrite commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
rfkill now allows to report a reason for the hw_rfkill state.
Allow cfg80211 drivers to specify this reason.
Keep the current API to use the default reason
(RFKILL_HARD_BLOCK_SIGNAL).
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://lore.kernel.org/r/20210322204633.102581-4-emmanuel.grumbach@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch moved the mptcp_addr_info struct from protocol.h to mptcp.h,
added a new struct mptcp_addr_info member addr in struct mptcp_out_options,
and dropped the original addr, addr6, addr_id and port fields in it. Then
we can use opts->addr to get the adding address from PM directly using
mptcp_pm_add_addr_signal.
Since the port number became big-endian now, use ntohs to convert it
before sending it out with the ADD_ADDR suboption. Also convert it
when passing it to add_addr_generate_hmac or printing it out.
Co-developed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following batch contains Netfilter/IPVS updates for your net-next tree:
1) Simplify log infrastructure modularity: Merge ipv4, ipv6, bridge,
netdev and ARP families to nf_log_syslog.c. Add module softdeps.
This fixes a rare deadlock condition that might occur when log
module autoload is required. From Florian Westphal.
2) Moves part of netfilter related pernet data from struct net to
net_generic() infrastructure. All of these users can be modules,
so if they are not loaded there is no need to waste space. Size
reduction is 7 cachelines on x86_64, also from Florian.
2) Update nftables audit support to report events once per table,
to get it aligned with iptables. From Richard Guy Briggs.
3) Check for stale routes from the flowtable garbage collector path.
This is fixing IPv6 which breaks due missing check for the dst_cookie.
4) Add a nfnl_fill_hdr() function to simplify netlink + nfnetlink
headers setup.
5) Remove documentation on several statified functions.
6) Remove printk on netns creation for the FTP IPVS tracker,
from Florian Westphal.
7) Remove unnecessary nf_tables_destroy_list_lock spinlock
initialization, from Yang Yingliang.
7) Remove a duplicated forward declaration in ipset,
from Wan Jiabing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
all have been moved to generic_net infra. On x86_64, this reduces
struct net size from 70 to 63 cache lines (4480 to 4032 byte).
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
dwork struct is large (>128 byte) and not needed when conntrack module
is not loaded.
Place it in net_generic data instead. The struct net dwork member is now
obsolete and will be removed in a followup patch.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
No need to keep this in struct net, place it in the net_generic data.
The sysctl pointer is removed from struct net in a followup patch.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This moves all nf_tables pernet data from struct net to a net_generic
extension, with the exception of the gencursor.
The latter is used in the data path and also outside of the nf_tables
core. All others are only used from the configuration plane.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This allows followup patch to remove these members from struct net.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Group all the often used fields in the first cache line,
to reduce cache line misses.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Order fields to increase locality for most used protocols.
udplite and icmp are moved at the end.
Same for proc_net_devsnmp6 which is not used in fast path.
This potentially saves one cache line miss for typical TCP/UDP over IPv4/IPv6.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MPTCP reset option allows to carry a mptcp-specific error code that
provides more information on the nature of a connection reset.
Reset option data received gets stored in the subflow context so it can
be sent to userspace via the 'subflow closed' netlink event.
When a subflow is closed, the desired error code that should be sent to
the peer is also placed in the subflow context structure.
If a reset is sent before subflow establishment could complete, e.g. on
HMAC failure during an MP_JOIN operation, the mptcp skb extension is
used to store the reset information.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2021-04-01
The following pull-request contains BPF updates for your *net-next* tree.
We've added 68 non-merge commits during the last 7 day(s) which contain
a total of 70 files changed, 2944 insertions(+), 1139 deletions(-).
The main changes are:
1) UDP support for sockmap, from Cong.
2) Verifier merge conflict resolution fix, from Daniel.
3) xsk selftests enhancements, from Maciej.
4) Unstable helpers aka kernel func calling, from Martin.
5) Batches ops for LPM map, from Pedro.
6) Fix race in bpf_get_local_storage, from Yonghong.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
struct ctl_table_header is declared twice. One is declared
at 46th line. The blew one is not needed. Remove the duplicate.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although these two functions are only used by TCP, they are not
specific to TCP at all, both operate on skmsg and ingress_msg,
so fit in net/core/skmsg.c very well.
And we will need them for non-TCP, so rename and move them to
skmsg.c and export them to modules.
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210331023237.41094-13-xiyou.wangcong@gmail.com
This is similar to tcp_read_sock(), except we do not need
to worry about connections, we just need to retrieve skb
from UDP receive queue.
Note, the return value of ->read_sock() is unused in
sk_psock_verdict_data_ready(), and UDP still does not
support splice() due to lack of ->splice_read(), so users
can not reach udp_read_sock() directly.
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20210331023237.41094-12-xiyou.wangcong@gmail.com
Currently sockmap calls into each protocol to update the struct
proto and replace it. This certainly won't work when the protocol
is implemented as a module, for example, AF_UNIX.
Introduce a new ops sk->sk_prot->psock_update_sk_prot(), so each
protocol can implement its own way to replace the struct proto.
This also helps get rid of symbol dependencies on CONFIG_INET.
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210331023237.41094-11-xiyou.wangcong@gmail.com
ip6_dst_ops have cache line alignement.
Moving it at beginning of netns_ipv6
removes a 48 byte hole, and shrinks netns_ipv6
from 12 to 11 cache lines.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By shuffling around some fields to remove 8 bytes of hole,
we can save one cache line.
pahole result before/after the patch :
/* size: 768, cachelines: 12, members: 139 */
/* sum members: 673, holes: 11, sum holes: 39 */
/* padding: 56 */
/* paddings: 2, sum paddings: 7 */
/* forced alignments: 1 */
->
/* size: 704, cachelines: 11, members: 139 */
/* sum members: 673, holes: 10, sum holes: 31 */
/* paddings: 2, sum paddings: 7 */
/* forced alignments: 1 */
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct inet_timewait_death_row uses two cache lines, because we want
tw_count to use a full cache line to avoid false sharing.
Rework its definition and placement in netns_ipv4 so that:
1) We add 60 bytes of padding after tw_count to avoid
false sharing, knowing that tcp_death_row will
have ____cacheline_aligned_in_smp attribute.
2) We do not risk padding before tcp_death_row, because
we move it at the beginning of netns_ipv4, even if new
fields are added later.
3) We do not waste 48 bytes of padding after it.
Note that I have not changed dccp.
pahole result for struct netns_ipv4 before/after the patch :
/* size: 832, cachelines: 13, members: 139 */
/* sum members: 721, holes: 12, sum holes: 95 */
/* padding: 16 */
/* paddings: 2, sum paddings: 55 */
->
/* size: 768, cachelines: 12, members: 139 */
/* sum members: 673, holes: 11, sum holes: 39 */
/* padding: 56 */
/* paddings: 2, sum paddings: 7 */
/* forced alignments: 1 */
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move dst_check() to the garbage collector path. Stale routes trigger the
flow entry teardown state which makes affected flows go back to the
classic forwarding path to re-evaluate flow offloading.
IPv6 requires the dst cookie to work, store it in the flow_tuple,
otherwise dst_check() always fails.
Fixes: e5075c0bad ("netfilter: flowtable: call dst_check() to fall back to classic forwarding")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
modprobe calls from the nf_logger_find_get() API causes deadlock in very
special cases because they occur with the nf_tables transaction mutex held.
In the specific case of nf_log, deadlock is via:
A nf_tables -> transaction mutex -> nft_log -> modprobe -> nf_log_syslog \
-> pernet_ops rwsem -> wait for C
B netlink event -> rtnl_mutex -> nf_tables transaction mutex -> wait for A
C close() -> ip6mr_sk_done -> rtnl_mutex -> wait for B
Earlier patch added NFLOG/xt_LOG module softdeps to avoid the need to load
the backend module during a transaction.
For nft_log we would have to add a softdep for both nfnetlink_log or
nf_log_syslog, since we do not know in advance which of the two backends
are going to be configured.
This defers the modprobe op until after the transaction mutex is released.
Tested-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Remove nf_log_common. Now that all per-af modules have been merged
there is no longer a need to provide a helper module.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Provide bridge log support from nf_log_syslog.
After the merge there is no need to load the "real packet loggers",
all of them now reside in the same module.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When UDP packets generated locally by a socket with UDP_SEGMENT
traverse the following path:
UDP tunnel(xmit) -> veth (segmentation) -> veth (gro) ->
UDP tunnel (rx) -> UDP socket (no UDP_GRO)
ip_summed will be set to CHECKSUM_PARTIAL at creation time and
such checksum mode will be preserved in the above path up to the
UDP tunnel receive code where we have:
__iptunnel_pull_header() -> skb_pull_rcsum() ->
skb_postpull_rcsum() -> __skb_postpull_rcsum()
The latter will convert the skb to CHECKSUM_NONE.
The UDP GSO packet will be later segmented as part of the rx socket
receive operation, and will present a CHECKSUM_NONE after segmentation.
Additionally the segmented packets UDP CB still refers to the original
GSO packet len. Overall that causes unexpected/wrong csum validation
errors later in the UDP receive path.
We could possibly address the issue with some additional checks and
csum mangling in the UDP tunnel code. Since the issue affects only
this UDP receive slow path, let's set a suitable csum status there.
Note that SKB_GSO_UDP_L4 or SKB_GSO_FRAGLIST packets lacking an UDP
encapsulation present a valid checksum when landing to udp_queue_rcv_skb(),
as the UDP checksum has been validated by the GRO engine.
v2 -> v3:
- even more verbose commit message and comments
v1 -> v2:
- restrict the csum update to the packets strictly needing them
- hopefully clarify the commit message and code comments
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ipv6_dev_find to ipv6_stub to allow lookup of net_devices by IPV6
address in net/ipv4/icmp.c.
Signed-off-by: Andreas Roeseler <andreas.a.roeseler@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Section 8 of RFC 8335 specifies potential security concerns of
responding to PROBE requests, and states that nodes that support PROBE
functionality MUST be able to enable/disable responses and that
responses MUST be disabled by default
Signed-off-by: Andreas Roeseler <andreas.a.roeseler@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After resilient next-hop groups have been added recently, there are two
types of multipath next-hop groups: the legacy "mpath", and the new
"resilient". Calling the legacy next-hop group type "mpath" is unfortunate,
because that describes the fact that a packet could be forwarded in one of
several paths, which is also true for the resilient next-hop groups.
Therefore, to make the naming clearer, rename various artifacts to reflect
the assumptions made. Therefore as of this patch:
- The flag for multipath groups is nh_grp_entry::is_multipath. This
includes the legacy and resilient groups, as well as any future group
types that behave as multipath groups.
Functions that assume this have "mpath" in the name.
- The flag for legacy multipath groups is nh_grp_entry::hash_threshold.
Functions that assume this have "hthr" in the name.
- The flag for resilient groups is nh_grp_entry::resilient.
Functions that assume this have "res" in the name.
Besides the above, struct nh_grp_entry::mpath was renamed to ::hthr as
well.
UAPI artifacts were obviously left intact.
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The purpose of this lock is to avoid a bottleneck in the query/report
event handler logic.
By previous patches, almost all mld data is protected by RTNL.
So, the query and report event handler, which is data path logic
acquires RTNL too. Therefore if a lot of query and report events
are received, it uses RTNL for a long time.
So it makes the control-plane bottleneck because of using RTNL.
In order to avoid this bottleneck, mc_lock is added.
mc_lock protect only per-interface mld data and per-interface mld
data is used in the query/report event handler logic.
So, no longer rtnl_lock is needed in the query/report event handler logic.
Therefore bottleneck will be disappeared by mc_lock.
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When query/report packets are received, mld module processes them.
But they are processed under BH context so it couldn't use sleepable
functions. So, in order to switch context, the two workqueues are
added which processes query and report event.
In the struct inet6_dev, mc_{query | report}_queue are added so it
is per-interface queue.
And mc_{query | report}_work are workqueue structure.
When the query or report event is received, skb is queued to proper
queue and worker function is scheduled immediately.
Workqueues and queues are protected by spinlock, which is
mc_{query | report}_lock, and worker functions are protected by RTNL.
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ifmcaddr6 has been protected by inet6_dev->lock(rwlock) so that
the critical section is atomic context. In order to switch this context,
changing locking is needed. The ifmcaddr6 actually already protected by
RTNL So if it's converted to use RCU, its control path context can be
switched to sleepable.
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ip6_sf_list has been protected by mca_lock(spin_lock) so that the
critical section is atomic context. In order to switch this context,
changing locking is needed. The ip6_sf_list actually already protected
by RTNL So if it's converted to use RCU, its control path context can
be switched to sleepable.
But It doesn't remove mca_lock yet because ifmcaddr6 isn't converted
to RCU yet. So, It's not fully converted to the sleepable context.
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sflist has been protected by rwlock so that the critical section
is atomic context.
In order to switch this context, changing locking is needed.
The sflist actually already protected by RTNL So if it's converted
to use RCU, its control path context can be switched to sleepable.
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The purpose of mc_lock is to protect inet6_dev->mc_tomb.
But mc_tomb is already protected by RTNL and all functions,
which manipulate mc_tomb are called under RTNL.
So, mc_lock is not needed.
Furthermore, it is spinlock so the critical section is atomic.
In order to reduce atomic context, it should be removed.
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mcast.c has several timers for delaying works.
Timer's expire handler is working under atomic context so it can't use
sleepable things such as GFP_KERNEL, mutex, etc.
In order to use sleepable APIs, it converts from timers to delayed work.
But there are some critical sections, which is used by both process
and BH context. So that it still uses spin_lock_bh() and rwlock.
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many tcp sysctls are either bools or small ints that can fit into u8.
Reducing space taken by sysctls can save few cache line misses
when sending/receiving data while cpu caches are empty,
for example after cpu idle period.
This is hard to measure with typical network performance tests,
but after this patch, struct netns_ipv4 has shrunk
by three cache lines.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For these sysctls, their dedicated helpers have
to use proc_dou8vec_minmax().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This sysctl uses ip_fwd_update_priority() helper,
so the conversion needs to change it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These sysctls that can fit in one byte instead of one int
are converted to save space and thus reduce cache line misses.
- icmp_echo_ignore_all, icmp_echo_ignore_broadcasts,
- icmp_ignore_bogus_error_responses, icmp_errors_use_inbound_ifaddr
- tcp_ecn, tcp_ecn_fallback
- ip_default_ttl, ip_no_pmtu_disc, ip_fwd_use_pmtu
- ip_nonlocal_bind, ip_autobind_reuse
- ip_dynaddr, ip_early_demux, raw_l3mdev_accept
- nexthop_compat_mode, fwmark_reflect
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
