Decoupling widgets from DAPM context is required when extending the ASoC
core to cross-device paths. Even the list of widgets are now kept in
struct snd_soc_card, the widget listing in sysfs and debugs remain sorted
per device.
This patch makes possible to build cross-device paths but does not extend
yet the DAPM to handle codec bias and widget power changes of an another
device.
Cross-device paths are registered by listing the widgets from device A in
a map for device B. In case of conflicting widget names between the devices,
a uniform name prefix is needed to separate them. See commit ead9b91
"ASoC: Add optional name_prefix for kcontrol, widget and route names" for
help.
An example below shows a path that connects MONO out of A into Line In of B:
static const struct snd_soc_dapm_route mapA[] = {
{"MONO", NULL, "DAC"},
};
static const struct snd_soc_dapm_route mapB[] = {
{"Line In", NULL, "MONO"},
};
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Decoupling DAPM paths from DAPM context is a first prerequisite when
extending ASoC core to cross-device paths. This patch is almost a nullop and
does not allow to construct cross-device setup but the path clean-up part in
dapm_free_widgets is prepared to remove cross-device paths between a device
being removed and others.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Gain for LineInAmp Right uses LINEGAIN[5:3], which means that
offset for right channel should be 4.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Some gains were incorrectly configured for dB values.
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
After coming back from suspend, the timeout waiting for Phoenix
chip to complete its power up sequence is not enough, which leaves
the codec cache value for some registers in an outdated state.
Increase the timeout value to wait for the power up sequence
to correclty complete.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Enable plug detection interrupt mask in order to get headset
PLUGINT/UNPLUGINT interrupts.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
On Phoenix 1.1, the INTID register default value is an invalid
one, causing the interrupt handler to think the phoenix power on
sequence is ready before it actually finishes.
This causes some i2c errors when trying to configure twl.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Phoenix 1.1 supports automatic power on sequence, a
verification is added to use it with new revision of
the chip.
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The mux control has 4 elements not 3
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The twl6040 can support more sample rates other than 88.2 and 96k.
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch moves all the PCM error handling for clock config
out of trigger() and startup() and into prepare().
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch restores the CODEC bias level at resume().
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch adds support for the twl6040 headset and handset
MUX controls.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Multiples interrupts can be received. The irq handler is modified
to attend all of them.
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Update the codec to use the new twl core register macros
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Use jack framework to enable detection for the headset microphone
and stereo output in the sdp4430.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: David Anders <x0132446@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch adds support for reporting twl6040 headset and
handset jack events.
The machine driver retrieves and report the status through
twl6040_hs_jack_detect.
A workq is used to debounce of the irq.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
twl4030 series of codecs supports S32_LE with msbits=24.
Replace the S24_LE with S32_LE format, and add constraint
for 24msbit in case of 32 S32_LE format.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Remove redundant parentheses/spaces in the use of the sizeof
operator.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This helps ensure that the ramp logic is reset when powering back up.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
In some cases it was not possible to follow the appropiate power
ON/OFF sequence like in cases where the PGA needs to be enabled
before the driver and disabled before the PGA for pop reduction.
Add a widget to support output driver (speaker, haptic, vibra, etc)
drivers where power ON/OFF ordering is important.
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
soc_unregister_ac97_dai_link() takes a CODEC as an argument, not a
rtd like the registration function, so give it what it's looking for.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Fix "ASoC: Fix bias power down of non-DAPM codec" for 3.6.37 will cause a
build error when merging into ASoC for-2.6.38. Fix the issue by doing a
change that commit ce6120c "ASoC: Decouple DAPM from CODECs" would do.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently bias of non-DAPM codec will be powered down (standby/off) whenever
there is a stream stop. This is wrong in simultaneous playback/capture since
the bias is put down immediately after stopping the first stream.
Fix this by using the codec->active count when figuring out the needed bias
level after stream stop.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The compiler really ought to have been warning about unreferenced
variables...
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
flush_scheduled_work() is deprecated and scheduled to be removed.
* cancel[_delayed]_work() + flush_scheduled_work() ->
cancel[_delayed]_work_sync().
* wm8350, wm8753 and soc-core use custom code to cancel a delayed
work, execute it immediately if it was pending and wait for its
completion. This is equivalent to flush_delayed_work_sync(). Use
it instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Provide the user with a boolean control then automatically select
the deemphasis filter most closely matching the sample rate.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
We're already flagged as using symmetric rates so we don't need to
have a custom implementation.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
If the following scenario has been followed:
1. Enable analog bypass
amixer sset 'Analog Left Bypass' on
amixer sset 'Analog Right Bypass' on
2. Start playback
aplay -fdat -d3 /dev/zero
After the playback stopped (3 sec), and the soc timeout (5 sec),
the digital parts of the codec will remain powered up.
This means that the DAI clocks are continue to run, the
oscillator remain operational, etc.
Use the SND_SOC_DAPM_POST_PMD widget to get notification
about the stopped stream, and power down the digital
part of the codec.
If the analog bypass is enabled, than the codec will remain in
BIAS_ON level, and things will work correctly.
In case, if the bypass is disabled, than the codec will
fall to BIAS_STANDBY than to BIAS_OFF level, as it used
to.
The digital part of DAC33 is initialized at every stream start
(DAPM_PRE:PRE_PMU event), so subsequent streams (within 5 sec)
will have working DAI.
When the codec is coming out from BIAS_OFF, the full power-up
sequence followed by the same DAPM_PRE widget event will power up
the digital part.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Add glue driver to make s3c24xx-i2s and uda1380 produce some sound on
H1940.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The oversampling rate of the DAC and ADC can be controlled to optimise
for either low power consumption or maximum performance.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Tune the FLL gain for optimal performance according to evaluation
results.
Signed-off-by: Mario Becroft <mb@gem.win.co.nz>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Changes to both I2S and PCM code:
- Rates list extended up to 96kHz, it's tested on EDB9302 and works for both capture and
playback.
Signed-off-by: Alexander Sverdlin <subaparts@yandex.ru>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acc to WM8580 manual, the default value for R8 is 0x10, not 0x1c.
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Deemphasis control's .get callback should update control's value instead
of returning it - return value of callback function is used for indicating
error or success of operation.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Add FM stereo pins to the machine driver and add them as a
dapm widget.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Fix the compilation error introduced by patch:
ASoC: tlv320dac33: Avoid multiple soft power up
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The power for the DACs need to be enabled, even when only
the analog bypass is in use with the codec, otherwise
the audio is going to be distorted.
Make sure that the DACs are powered all the time, when
there is audio activity.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Use better name for the widget, and remove the 'Power'
from it's name.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Uk Kim <w0806.kim@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8994 supports mono signals - enable this in the driver. With DSP
mode an automatic data channel selector is available, activate this
when in mono mode.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
In case the codec driver did not provide a read/write function,
codec->driver->read|write will be NULL. Ensure that we use the one
specified in codec->read|write to avoid oopsing when we access
the debugfs entries. This is achieved by using snd_soc_read() and
snd_soc_write().
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In case of SNDRV_PCM_FORMAT_S32_LE, we need to set WM8580_AIF_LENGTH_32,
rather than WM8580_AIF_LENGTH_24.
Also, the BCLK has to be 64fs, for sample size of 20, 24 and 32 bits.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Properly free the resources in the case of snd_card_register failure
and soc_register_ac97_dai_link failure.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Properly free the resources in the case of soc_register_ac97_dai_link failure.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is no need to mark this function as inline. Inline functions
usually are small and concise functions that benefit from not needing
to set up a stack frame and undergo a call/ret sequence upon each
invocation.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
By using strncpy() if the source string does not have a null byte in the
first n bytes, then the destination string is not null-terminated.
This can be fixed in a two-step process by manually null-terminating the
array after the use of strncpy() or by using strlcpy().
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 2eea392 "ASoC: Add support for optional auxiliary dailess codecs"
added much of code that can be shared with DAI link codec probing/removal.
Merge now this common code into new soc_probe_codec, soc_remove_codec and
soc_post_component_init functions.
Error prints in these functions are converted to use dev_err and to print
the error code.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Added an optional name member to snd_soc_cache_ops to enable more
sensible diagnostic messages during cache init, exit and sync.
Remove redundant newline in source code.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch fixed intial return value to be a '0' as asuccess on
set_audio_clock_heirachy(). This avoids unintended error on initialize.
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As jack detection can trigger DAPM and the latency in debouncing can create
confusing windows in operation provide some trace events which will hopefully
help in diagnostics. The soc-jack core traces all reports that it gets and
the resulting notifications to upper layers. An event for jack IRQs is also
provided for instrumentation of debounce, and used in the GPIO jack code.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
As the comments of snd_soc_instantiate_cards() said,
snd_soc_instantiate_cards() must be called with client_mutex.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
SPKOUTL_BOOST start from third bit, SPKOUTLR_BOOST start from 0 bit.
Signed-off-by: Uk Kim <w0806.kim@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Currently the machine driver can only do bias level configuration before
the CODEC bias level is brought up. This means that the machine cannot do
any configuration which depends on the CODEC bias level being maintained.
Provide a post-CODEC callback which allows the machine driver to do things
like enable the FLL on a CODEC which is brought down to BIAS_OFF when idle.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ASoC: omap: N810: Don't select CONFIG_OMAP_MUX but make it as dependency
ALSA: hda: Use "alienware" model quirk for another SSID
ASoC: WM8731: Fix incorrect mask for bypass path disable
s6105-ipcam: fix compilation
s6000-pcm: fix compilation
s6000-i2s: fix compilation
ASoC: Fix missing spin_unlock_irqrestore
ALSA: Fix SNDCTL_DSP_RESET ioctl for OSS emulation
ASoC: Add missing dev_set_drvdata in p1022_ds_probe
ASoC: Add missing dev_set_drvdata in mpc8610_hpcd_probe
ASoC: Remove unneeded !! operations while checking return value of nuc900_checkready
ASoC: Fix compile error for nuc900-pcm.c
ASoC: Fix prototype for nuc900_ac97_probe and nuc900_ac97_remove
ASoC: Fix compile error for nuc900-ac97.c
ALSA: hda: Use BIOS auto-parsing instead of existing model quirk for MEDION MD2
When we disable the WM8994 FLL code path sharing means that we end up
writing out a configuration. Currently this is the currently active
input and output frequency (which causes snd_soc_update_bits() to
suppress actual writes both immediately and in the common case where
we reenable the same configuration later) but we allow machine drivers
to pass through a source of zero. Since the register values written
are one less than the source constants this causes corruption of other
bitfields in the register.
Fix this by using the most recently configured FLL source when none is
provided.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: stable@kernel.org
We want the index of DAI's driver here.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow the CODEC driver structure to be marked const by making all
the APIs that use it do so.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch allows machine drivers to override the compression type
provided by the codec driver.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Make sure to use codec->reg_def_copy instead of codec_drv->reg_cache_default
wherever necessary. This change is necessary because in the next patch we
move the cache initialization code outside snd_soc_register_codec() and by that
time any data marked as __devinitconst such as the original reg_cache_default
array might have already been freed by the kernel.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The snd_soc_codec_conf struct now holds codec specific configuration
information.
A new configuration option has been added to allow machine drivers to
override the compression type set by the codec driver.
In the absence of providing an snd_soc_codec_conf struct or when providing
one but not setting the compress_type member to anything, the one supplied
by the codec driver will be used instead. In all other cases the one
set in the snd_soc_codec_conf struct takes effect.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We need to keep a copy of the compress_type supplied by the codec driver
so that we can override it if necessary with whatever the machine driver
has provided us with. The reason for not modifying the codec->driver
struct directly is that ideally we'd like to keep it const.
Adjust the code in soc-cache and soc-core to make use of the compress_type
member in the snd_soc_codec struct.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Blind copy of codec finding algorithm from soc_bind_dai_link does not work
in soc_probe_aux_dev if matching codec name is not found. In that case the
code falls through and tries to start the probing procedure with invalid
codec pointer.
Fix this and add an error print showing the codec name that cannot be found.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In alc5623_i2c_probe(),
the default case for checking alc5623->id behaves the same as case 0x23.
However, In alc5623_probe() the default case for checking alc5623->id
becomes to be the same as case 0x21.
This makes the meaning of default case inconsistent.
Since we have checked codec id in alc5623_i2c_probe() by comparing
vid2 with id->driver_data, it is not possible to run into the default case now.
In case we may add more supported devices to alc5623_i2c_table in the future,
this patch changes the default case return -EINVAL to let people know that
they should not run into this case. They should also add a new case accordingly
for the new id.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current FSI driver was checking register range on fsi_master_xxx function.
This runtime check was added to avoid an illegal access
from wrong/mistake implementation.
But it is useless check under the correct implementation.
This patch escape runtime check by using macro technique.
If there is wrong implementation, it will be compile error.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current FSI driver was checking register range on fsi_reg_xxx function.
This runtime check was added to avoid an illegal access
from wrong/mistake implementation.
But it is useless check under the correct implementation.
This patch escape runtime check by using macro technique.
If there is wrong implementation, it will be compile error.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There was a strange part where fsi->xxx had been used
for fsi_master_xxx function instead of master->xxx in current FSI.
This patch modify it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We shouldn't be assigning to the driver structure (which really ought
to be const, further patch to follow) though there's unlikely to be any
actual problem except in the unlikely case that two devices with the
same driver but different bus types appear in the same system.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Silly little grammar nit but it bugs the hell out of me.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Update some of the default configuration for the device to improve
the performance.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The deemphasis filter should be selected based on sample rate for
optimal performance.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
This is much more maintainable than the array.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The use of DAPM widgets, and extra routing can cause ordering
problems in the system.
Machine drivers should use the exported direct interface with
SND_SOC_DAPM_HP's event callback to manage the state of the
amplifier.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Not all omap boards use kernel based pin multiplexing so
CONFIG_SND_OMAP_SOC_N810 should not select it by default as it can make
harm to other boards in multi-board kernels.
Therefore put CONFIG_OMAP_MUX as a dependency to N810 ASoC machine driver.
Thanks to Tony Lindgren <tony@atomide.com> for noticing.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The mute/unmute is controled by SMUTE (Soft Mute Control bit):
0: Normal Operation (Default)
1: DAC outputs soft-muted
I think this change improves readability.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The paramters of the WM8958 multiband compressor can be tuned by the
user for their system using a graphical configuration tool on the host.
Allow the user to specify a set of such paramters in platform data and
select between them at runtime.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
We need a post notification as we need to shut down the MBC after the
data stops flowing rather than before.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Commit 2eea392 "ASoC: Add support for optional auxiliary dailess codecs"
causes a build failure in soc-core.c: soc_probe_aux_dev since code tries to
access non-existing struct snd_soc_dapm_context and struct snd_soc_card
members.
Root cause for this was a double accident. Author sent the RFC patch from
top of another patch set and the RFC got committed. Fix the build failure
by removing the code line that depends on that another patch set.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
According to the datasheet the bypass path enable/disable is
bit 3 therefore we need 0x8 and not 0x4.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
New DAPM widgets, and paths to enable both channels at the
same time (for stereo output).
With this path the switch time difference can be avoided
between left and right channels.
The original DAPM paths can be still used, if only one of
TPA's output has been connected to a speaker, but for most of
the cases, switching to the stereo path is better.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
