As per the latest Data Manual, for newer samples,
the nominal voltage required for VDD_CORE at OPP_NOM can be
upto 1.06V which was 1.03V earlier.
Update the regulator max voltage constraint for SMPS7,
connected to VDD_CORE, to meet this requirement.
Document reference:
DRA74 Data Manual, SPRS857M - Dec 2012, Revised Oct 2014.
DRA72 Data Manual, SPRS906G - Dec 2012, revised Oct 2014.
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The max expected voltage for VDD_GPU, connected to SMPS6, is 1.25V.
Correct regulator max voltage constraint to meet this requirement.
Document reference: DRA74 Data Manual, SPRS857M - Dec 2012,
Revised Oct 2014.
Fixes: c56a831ca4 ("ARM: dts: DRA7: Add TPS659038 PMIC nodes")
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Caused by a copy & paste error. Note that even with
this bug AM437x SK display still works because GPIO
mux mode is always enabled. It's still wrong to mux
somebody else's pin.
Luckily ball D25 (offset 0x238 - gpio5_8) on AM437x
isn't used for anything.
While at that, also replace a pullup with a pulldown
as that gpio should be normally low, not high.
Cc: <stable@vger.kernel.org> # v3.17+
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit f4d809ec55b6 ("ARM: dts: Fix gpmc timings for omap 2430sdp")
added GPMC timings for 2430sdp. This however broke the Ethernet
for some versions of u-boot using a different L3 clock frequency:
set_gpmc_timing_reg: GPMC error! CS5: cs_rd_off: 233 ns, 39 ticks > 31
omap-gpmc 6e000000.gpmc: failed to set gpmc timings for: ethernet
This is because the smsc91x timings from 1.1.4 u-boot overflow the
GPMC registers when booted with 1.1.3 version of u-boot.
Let's fix this issue by using the better timings from u-boot 1.1.3
as they also work on 1.1.4 and are faster.
Note that so far the attempts over the years to calculate the GPMC
timings on the SDP boards have failed probably because of the
unknown latencies added by the FPGA on the debug boards.
Reported-by: Nishanth Menon <nm@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The DT branch adds a lot of new stuff for additional SoC and board
support. The branch is the largest one and contains 513 out of the
total 972 non-merge arm-soc changesets for 3.19.
Most of the changes are about enabling additional on-chip devices for
existing machines, but there are also an unusual number of new SoC
types being added this time:
* AMLogic Meson8
* ARM Realview in DT mode
* Allwinner A80
* Broadcom BCM47081
* Broadcom Cygnus
* Freescale LS1021A
* Freescale Vybrid 500 series
* Mediatek MT6592, MT8127, MT8135
* STMicroelectronics STiH410
* Samsung Exynos4415
The level of support for the above differs widely, some are just
stubs with nothing more than CPU, memory and a UART, but others
are fairly complete. As usual, these get extended over time.
There are also many new boards getting added, this is the
list of model strings that are showing up in new dts files:
* ARM RealView PB1176
* Altera SOCFPGA Arria 10
* Asus RT-N18U (BCM47081)
* Buffalo WZR-1750DHP (BCM4708)
* Buffalo WZR-600DHP2 (BCM47081)
* Cygnus Enterprise Phone (BCM911360_ENTPHN)
* D-Link DIR-665
* Google Spring
* IGEP COM MODULE Rev. G (TI OMAP AM/DM37x)
* IGEPv2 Rev. F (TI OMAP AM/DM37x)
* LS1021A QDS Board
* LS1021A TWR Board
* LeMaker Banana Pi
* MarsBoard RK3066
* MediaTek MT8127 Moose Board
* MediaTek MT8135 evaluation board
* Mele M3
* Merrii A80 Optimus Board
* Netgear R6300 V2 (BCM4708)
* Nomadik STN8815NHK
* NovaTech OrionLXm
* Olimex A20-OLinuXino-LIME2
* Raspberry Pi Model B+
* STiH410 B2120
* Samsung Monk board
* Samsung Rinato board
* Synology DS213j
* Synology DS414
* TBS2910 Matrix ARM mini PC
* TI AM5728 BeagleBoard-X15
* Toradex Colibri VF50 on Colibri Evaluation Board
* Zynq ZYBO Development Board
Other notable changes include:
* exynos: cleanup of existing dts files
* mvebu: improved pinctrl support for Armada 370/XP
* nomadik: restructuring dts files
* omap: added CAN bus support
* shmobile: added clock support for some SoCs
* shmobile: added sound support for some SoCs
* sirf: reset controller support
* sunxi: continuing the relicensing under dual GPL/MIT
* sunxi: lots of new on-chip device support
* sunxi: working simplefb support (long awaited)
* various: provide stdout-path property for earlycon
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=BHwA
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Arnd Bergmann:
"The DT branch adds a lot of new stuff for additional SoC and board
support. The branch is the largest one and contains 513 out of the
total 972 non-merge arm-soc changesets for 3.19.
Most of the changes are about enabling additional on-chip devices for
existing machines, but there are also an unusual number of new SoC
types being added this time:
- AMLogic Meson8
- ARM Realview in DT mode
- Allwinner A80
- Broadcom BCM47081
- Broadcom Cygnus
- Freescale LS1021A
- Freescale Vybrid 500 series
- Mediatek MT6592, MT8127, MT8135
- STMicroelectronics STiH410
- Samsung Exynos4415
The level of support for the above differs widely, some are just stubs
with nothing more than CPU, memory and a UART, but others are fairly
complete. As usual, these get extended over time.
There are also many new boards getting added, this is the list of
model strings that are showing up in new dts files:
- ARM RealView PB1176
- Altera SOCFPGA Arria 10
- Asus RT-N18U (BCM47081)
- Buffalo WZR-1750DHP (BCM4708)
- Buffalo WZR-600DHP2 (BCM47081)
- Cygnus Enterprise Phone (BCM911360_ENTPHN)
- D-Link DIR-665
- Google Spring
- IGEP COM MODULE Rev. G (TI OMAP AM/DM37x)
- IGEPv2 Rev. F (TI OMAP AM/DM37x)
- LS1021A QDS Board
- LS1021A TWR Board
- LeMaker Banana Pi
- MarsBoard RK3066
- MediaTek MT8127 Moose Board
- MediaTek MT8135 evaluation board
- Mele M3
- Merrii A80 Optimus Board
- Netgear R6300 V2 (BCM4708)
- Nomadik STN8815NHK
- NovaTech OrionLXm
- Olimex A20-OLinuXino-LIME2
- Raspberry Pi Model B+
- STiH410 B2120
- Samsung Monk board
- Samsung Rinato board
- Synology DS213j
- Synology DS414
- TBS2910 Matrix ARM mini PC
- TI AM5728 BeagleBoard-X15
- Toradex Colibri VF50 on Colibri Evaluation Board
- Zynq ZYBO Development Board
Other notable changes include:
- exynos: cleanup of existing dts files
- mvebu: improved pinctrl support for Armada 370/XP
- nomadik: restructuring dts files
- omap: added CAN bus support
- shmobile: added clock support for some SoCs
- shmobile: added sound support for some SoCs
- sirf: reset controller support
- sunxi: continuing the relicensing under dual GPL/MIT
- sunxi: lots of new on-chip device support
- sunxi: working simplefb support (long awaited)
- various: provide stdout-path property for earlycon"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (510 commits)
ARM: dts: rk3288: add arm,cpu-registers-not-fw-configured
Revert "ARM: dts: rockchip: temporarily disable smp on rk3288"
ARM: BCM5301X: Add DT for Buffalo WZR-600DHP2
ARM: BCM5301X: Add DT for Asus RT-N18U
ARM: BCM5301X: Add DT for Buffalo WZR-1750DHP
ARM: BCM5301X: Add DT for Netgear R6300 V2
ARM: BCM5301X: Add buttons for Netgear R6250
ARM: dts: rockchip: Add input voltage supply regulators in pmic for Marsboard
ARM: BCM5301X: Add IRQs to Broadcom's bus-axi in DTS file
arm: dts: zynq: Add Digilent ZYBO board
arm: dts: zynq: Move crystal freq. to board level
doc: dt: vendor-prefixes: Add Digilent Inc
Documentation: devicetree: Fix Xilinx VDMA specification
ARM: dts: rockchip: set FIFO size for SDMMC, SDIO and EMMC on rk3066 and rk3188
ARM: dts: rockchip: add label property for leds on Radxa Rock
ARM: BCM5301X: Add LEDs for Netgear R6250 V1
ARM: BCM5301X: Add Broadcom's bus-axi to the DTS file
ARM: dts: add sysreg phandle to i2c device nodes for exynos
ARM: dts: Remove unused bootargs from exynos3250-rinato
ARM: dts: add board dts file for Exynos3250-based Monk board
...
New and updated SoC support, notable changes include:
* bcm: brcmstb SMP support
* bcm: initial iproc/cygnus support
* exynos: Exynos4415 SoC support
* exynos: PMU and suspend support for Exynos5420
* exynos: PMU support for Exynos3250
* exynos: pm related maintenance
* imx: new LS1021A SoC support
* imx: vybrid 610 global timer support
* integrator: convert to using multiplatform configuration
* mediatek: earlyprintk support for mt8127/mt8135
* meson: meson8 soc and l2 cache controller support
* mvebu: Armada 38x CPU hotplug support
* mvebu: drop support for prerelease Armada 375 Z1 stepping
* mvebu: extended suspend support, now works on Armada 370/XP
* omap: hwmod related maintenance
* omap: prcm cleanup
* pxa: initial pxa27x DT handling
* rockchip: SMP support for rk3288
* rockchip: add cpu frequency scaling support
* shmobile: r8a7740 power domain support
* shmobile: various small restart, timer, pci apmu changes
* sunxi: Allwinner A80 (sun9i) earlyprintk support
* ux500: power domain support
Overall, a significant chunk of changes, coming mostly from
the usual suspects: omap, shmobile, samsung and mvebu, all of
which already contain a lot of platform specific code in
arch/arm.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=lFoH
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Arnd Bergmann:
"New and updated SoC support, notable changes include:
- bcm:
brcmstb SMP support
initial iproc/cygnus support
- exynos:
Exynos4415 SoC support
PMU and suspend support for Exynos5420
PMU support for Exynos3250
pm related maintenance
- imx:
new LS1021A SoC support
vybrid 610 global timer support
- integrator:
convert to using multiplatform configuration
- mediatek:
earlyprintk support for mt8127/mt8135
- meson:
meson8 soc and l2 cache controller support
- mvebu:
Armada 38x CPU hotplug support
drop support for prerelease Armada 375 Z1 stepping
extended suspend support, now works on Armada 370/XP
- omap:
hwmod related maintenance
prcm cleanup
- pxa:
initial pxa27x DT handling
- rockchip:
SMP support for rk3288
add cpu frequency scaling support
- shmobile:
r8a7740 power domain support
various small restart, timer, pci apmu changes
- sunxi:
Allwinner A80 (sun9i) earlyprintk support
- ux500:
power domain support
Overall, a significant chunk of changes, coming mostly from the usual
suspects: omap, shmobile, samsung and mvebu, all of which already
contain a lot of platform specific code in arch/arm"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (187 commits)
ARM: mvebu: use the cpufreq-dt platform_data for independent clocks
soc: integrator: Add terminating entry for integrator_cm_match
ARM: mvebu: add SDRAM controller description for Armada XP
ARM: mvebu: adjust mbus controller description on Armada 370/XP
ARM: mvebu: add suspend/resume DT information for Armada XP GP
ARM: mvebu: synchronize secondary CPU clocks on resume
ARM: mvebu: make sure MMU is disabled in armada_370_xp_cpu_resume
ARM: mvebu: Armada XP GP specific suspend/resume code
ARM: mvebu: reserve the first 10 KB of each memory bank for suspend/resume
ARM: mvebu: implement suspend/resume support for Armada XP
clk: mvebu: add suspend/resume for gatable clocks
bus: mvebu-mbus: provide a mechanism to save SDRAM window configuration
bus: mvebu-mbus: suspend/resume support
clocksource: time-armada-370-xp: add suspend/resume support
irqchip: armada-370-xp: Add suspend/resume support
ARM: add lolevel debug support for asm9260
ARM: add mach-asm9260
ARM: EXYNOS: use u8 for val[] in struct exynos_pmu_conf
power: reset: imx-snvs-poweroff: add power off driver for i.mx6
ARM: imx: temporarily remove CONFIG_SOC_FSL from LS1021A
...
The remaining cleanups for 3.19 are to a large part result of
devicetree conversion nearing completion on two other platforms
besides AT91:
* Like AT91, Renesas shmobile is in the process to migrate to DT and
multiplatform, but using a different approach of doing it one
SoC at a time. For 3.19, the r8a7791 platform and associated\
"Koelsch" board are considered complete and we remove the non-DT
non-multiplatform support for this.
* The ARM Versatile Express has supported DT and multiplatform
for a long time, but we have still kept the legacy board files
around, because not all drivers were fully working before. We
have finally taken the last step to remove the board files.
Other changes in this branch are preparation for the later branches
or just unrelated to the more interesting changes:
* The dts files for arm64 get moved into per-vendor directories for
a clearer structure.
* Some dead code removal (zynq, exynos, davinci, imx)
* Using pr_*() macros more consistently instead of printk(KERN_*)
in some platform code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Apdh
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Arnd Bergmann:
"The remaining cleanups for 3.19 are to a large part result of
devicetree conversion nearing completion on two other platforms
besides AT91:
- Like AT91, Renesas shmobile is in the process to migrate to DT and
multiplatform, but using a different approach of doing it one SoC
at a time. For 3.19, the r8a7791 platform and associated "Koelsch"
board are considered complete and we remove the non-DT
non-multiplatform support for this.
- The ARM Versatile Express has supported DT and multiplatform for a
long time, but we have still kept the legacy board files around,
because not all drivers were fully working before. We have finally
taken the last step to remove the board files.
Other changes in this branch are preparation for the later branches or
just unrelated to the more interesting changes:
- The dts files for arm64 get moved into per-vendor directories for a
clearer structure.
- Some dead code removal (zynq, exynos, davinci, imx)
- Using pr_*() macros more consistently instead of printk(KERN_*) in
some platform code"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (71 commits)
ARM: zynq: Remove secondary_startup() declaration from header
ARM: vexpress: Enable regulator framework when MMCI is in use
ARM: vexpress: Remove non-DT code
ARM: imx: Remove unneeded .map_io initialization
ARM: dts: imx6qdl-sabresd: Fix the microphone route
ARM: imx: refactor mxc_iomux_mode()
ARM: imx: simplify clk_pllv3_prepare()
ARM: imx6q: drop unnecessary semicolon
ARM: imx: clean up machine mxc_arch_reset_init_dt reset init
ARM: dts: imx6qdl-rex: Remove unneeded 'fsl,mode' property
ARM: dts: imx6qdl-gw5x: Remove unneeded 'fsl,mode' property
ARM: dts: imx6qdl-sabresd: Use IMX6QDL_CLK_CKO define
ARM: at91: remove useless init_time for DT-only SoCs
ARM: davinci: Remove redundant casts
ARM: davinci: Use standard logging styles
ARM: shmobile: r8a7779: Spelling/grammar s/entity/identity/, s/map/mapping/
ARM: shmobile: sh7372: Spelling/grammar s/entity map/identity mapping/
ARM: shmobile: sh73a0: Spelling/grammar s/entity map/identity mapping/
ARM: EXYNOS: Remove unused static iomapping
ARM: at91: fix build breakage due to legacy board removals
...
These are bug fixes for harmless problems that were not important
enough to get fixed in 3.19. This contains updates to the MAINTAINERS
file, in particular:
- Ben Dooks stepped down as Samsung co-maintainer (thanks Ben for
long years of maintaining this). Kukjin Kim, who has been
doing the work de-facto by himself recently is now the
only maintainer.
- Liviu, Sudeep and Lorenzo from ARM now officially maintain the
Versatile Express platform, which was orphaned (thanks for
- Gregory Fong and Florian Fainelli help out on the Broadcom BCM7XXX
platform
- Ray Jui and Scott Branden are the future maintainers for the
newly merged Broadcom Cygnus platform. Welcome!
In terms of actual fixes, we have the usual set of OMAP bug fixes,
which Tony Lindgren separates out well from the other OMAP changes,
one really ep93xx regression fix against 3.11 that didn't make it for
3.18, a few GIC changes from Marc Zyngier as a preparation for
later rework (the current code is wrong in a harmless way), on
Tegra regression and one samsung spelling fix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=J1gB
-----END PGP SIGNATURE-----
Merge tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-critical bug fixes from Arnd Bergmann:
"These are bug fixes for harmless problems that were not important
enough to get fixed in 3.19. This contains updates to the MAINTAINERS
file, in particular:
- Ben Dooks stepped down as Samsung co-maintainer (thanks Ben for
long years of maintaining this). Kukjin Kim, who has been doing
the work de-facto by himself recently is now the only maintainer.
- Liviu, Sudeep and Lorenzo from ARM now officially maintain the
Versatile Express platform, which was orphaned (thanks for
- Gregory Fong and Florian Fainelli help out on the Broadcom BCM7XXX
platform
- Ray Jui and Scott Branden are the future maintainers for the newly
merged Broadcom Cygnus platform. Welcome!
In terms of actual fixes, we have the usual set of OMAP bug fixes,
which Tony Lindgren separates out well from the other OMAP changes,
one really ep93xx regression fix against 3.11 that didn't make it for
3.18, a few GIC changes from Marc Zyngier as a preparation for later
rework (the current code is wrong in a harmless way), on Tegra
regression and one samsung spelling fix"
* tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: imx6: fix bogus use of irq_get_irq_data
ARM: imx: irq: fix buggy usage of irq_data irq field
MAINTAINERS: ARM Versatile Express platform, add missing pattern
MAINTAINERS: ARM Versatile Express platform
arm: ep93xx: add dma_masks for the M2P and M2M DMA controllers
MAINTAINERS: Add ahci_st.c to ARCH/STI architecture
MAINTAINERS: add entry for the GISB arbiter driver
MAINTAINERS: update brcmstb entries
MAINTAINERS: update email address and cleanup for exynos entry
ARM: tegra: Re-add removed SoC id macro to tegra_resume()
MAINTAINERS: Entry for Cygnus/iproc arm architecture
ARM: OMAP: serial: remove last vestige of DTR_gpio support.
ARM: OMAP2+: gpmc: Get rid of "ti,elm-id not found" warning
ARM: EXYNOS: fix typo in static struct name "exynos5_list_diable_wfi_wfe"
ARM: OMAP2: Remove unnecessary KERN_* in omap_phy_internal.c
ARM: OMAP4+: Remove unused omap_l3_noc platform init
ARM: dts: Add twl keypad map for omap3 EVM
ARM: dts: Add twl keypad map for LDP
ARM: dts: Fix NAND last partition size on LDP
ARM: OMAP3: Fix errors for omap_l3_smx when booted with device tree
This will enable use of physical arch timers on rk3288, where each
core comes out of reset with a different virtual offset. Using
physical timers will help with SMP booting on coreboot and older
u-boot and should also allow suspend-resume and cpu-hotplug to work on
all firmwares.
Firmware which does initialize the cpu registers properly at boot and
cpu-hotplug can remove this property from the device tree.
Signed-off-by: Sonny Rao <sonnyrao@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
We now have the physical-timers patches lined up as a dependency in this same
branch, so we can revert the temporary disablement.
This reverts commit b77d43943e.
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds the IRQ number to the main dts file and some new dts files
for newly added devices.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=epqY
-----END PGP SIGNATURE-----
Merge tag 'bcm5301x-dt-2014-12-04' of https://github.com/hauke/linux into next/dt
Merge "ARM: BCM5301X: DT changes for v3.19 #2" from Hauke Mehrtens:
ARM: BCM5301X: dts updates
This adds the IRQ number to the main dts file and some new dts files
for newly added devices.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* tag 'bcm5301x-dt-2014-12-04' of https://github.com/hauke/linux:
ARM: BCM5301X: Add DT for Buffalo WZR-600DHP2
ARM: BCM5301X: Add DT for Asus RT-N18U
ARM: BCM5301X: Add DT for Buffalo WZR-1750DHP
ARM: BCM5301X: Add DT for Netgear R6300 V2
ARM: BCM5301X: Add buttons for Netgear R6250
ARM: BCM5301X: Add IRQs to Broadcom's bus-axi in DTS file
Signed-off-by: Olof Johansson <olof@lixom.net>
- mmc fifo sizes for Cortex-A9 SoCs
- labels for the leds on the RadxaRock
- core system supply for the Marsboard
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJUffEUAAoJEPOmecmc0R2Bk4QH/0O8+misF7MM3/EX0UOicb09
zrrVaPfH8GKHz3NlXGNZhIgy1coNoElBmdWPEb+XI+tRI3vKcyHtsJp78XHYupBl
yHFXjRYw4dHwwc08cQRDzf8qfWFpTnKX/gSBhgn5+kuIvylalLmnY8RjYtuQcaYW
DEc5B8eEMmmDH1Y3UBat+JOIJZY4NWxc9zmK+wRuMtcLt8ieCmgOWVMBjl8BerAe
Vdi0EM3YicA/HDzPVNq3xQK6cUtWDfKSFvkJhwc9Q40Yl4LQaOf2YMA2sZ/4+Qnl
F1LLJtJFMo9A0vECDJIfleXJRXnq0VjVp1Mn18Do8J6zsazzS94ppSDyk5EliVg=
=jMaL
-----END PGP SIGNATURE-----
Merge tag 'v3.19-rockchip-dts4' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Pull "last dts changes for 3.19" from Jason Cooper:
- rk3288 thermal driver that got accepted into the thermal tree
- mmc fifo sizes for Cortex-A9 SoCs
- labels for the leds on the RadxaRock
- core system supply for the Marsboard
* tag 'v3.19-rockchip-dts4' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Add input voltage supply regulators in pmic for Marsboard
ARM: dts: rockchip: set FIFO size for SDMMC, SDIO and EMMC on rk3066 and rk3188
ARM: dts: rockchip: add label property for leds on Radxa Rock
ARM: dts: rockchip: enable thermal on rk3288-evb board
ARM: dts: rockchip: add main thermal info to rk3288
ARM: dts: rockchip: add RK3288 Thermal data
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Armada 370/XP suspend/resume support
- mvebu SoC driver suspend/resume support
- irqchip
- clocksource
- mbus
- clk
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJUe0lIAAoJEP45WPkGe8Zn/IgP/jOO8c7t7dohRbAe3axzIcaC
DLL7d7j0AScZGXLx1/xJrFFY/P3gn3dlLR7HnT0t4K7vcW0kP4orMGo6FcGicSOZ
VzQf88cOkunKf9NTM1Y0LOXVWTHGuACiXAnxook5A6k+l0xQ1t+uewgEKrg/33VK
6WQ6woe2eYFwghkFwL3ybjttOPM5nxPef6v3TZ3LfwSUBsnSm70F1XiO8xZJH+LM
fL83P409LGWgohwSaXYRdPJcNM0U7QMNo6i/If9NNBhIkdKb6llhQ/DvI+aXUvqB
aD9/4t+Q75yki0mXIin6irltjspWsR8OFbaKZOM5IBFp/XrsKvNU+wy++7z9se9z
qfG1QYmKk3ddI0isoksuIJpfbrlbQqFKCGlNkn8HVi4xCYCijNgb5bUrHQ27Aa4U
GGisAOhqs9Ktpz96WeNKjvNQBSJZ3ESd6tlLrwCei8DwEdT0Z73jr1aEnulurpPG
A3kiUhVpRIU+w0cth5Kix2bZj7JGsykzu1x5xORLE+MN8RSgmoveGyY5CBp2MHrl
NxR/u98SD9I/rWT3DwQIKxM5ZqF4AAnyj4SaSWR/f40kWMU+A+eMEfo8VUeO88fl
ygeeHTghSf58gbdgganRfDyY8OaQHeYNNKbWK6c7vxyMX98vwHOtOb5JS3nn0p7q
Fugy/6qf+ZqYHT4nczJO
=uX+e
-----END PGP SIGNATURE-----
Merge tag 'mvebu-soc-suspend-3.19' of git://git.infradead.org/linux-mvebu into next/soc
Pull "mvebu SoC suspend changes for v3.19" from Jason Cooper:
- Armada 370/XP suspend/resume support
- mvebu SoC driver suspend/resume support
- irqchip
- clocksource
- mbus
- clk
* tag 'mvebu-soc-suspend-3.19' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: add SDRAM controller description for Armada XP
ARM: mvebu: adjust mbus controller description on Armada 370/XP
ARM: mvebu: add suspend/resume DT information for Armada XP GP
ARM: mvebu: synchronize secondary CPU clocks on resume
ARM: mvebu: make sure MMU is disabled in armada_370_xp_cpu_resume
ARM: mvebu: Armada XP GP specific suspend/resume code
ARM: mvebu: reserve the first 10 KB of each memory bank for suspend/resume
ARM: mvebu: implement suspend/resume support for Armada XP
clk: mvebu: add suspend/resume for gatable clocks
bus: mvebu-mbus: provide a mechanism to save SDRAM window configuration
bus: mvebu-mbus: suspend/resume support
clocksource: time-armada-370-xp: add suspend/resume support
irqchip: armada-370-xp: Add suspend/resume support
Documentation: dt-bindings: minimal documentation for MVEBU SDRAM controller
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
vsys is the core always-on supply of the Marsboard.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
IRQ support for Broadcom's bus-axi driver bcma was merged into John
Linville's wireless tree and will show up in 3.19. This patch makes use
of this feature in the DTS file for the the BCM5301X SoCs. I left the
PCIe controller out, because this still needs some discussion.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add a DTS describing the Digilent ZYBO board. Similar to ZED but with
a 50MHz crystal instead of 33MHz.
Acked-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The fact that all supported boards use the same 33MHz crystal is a
co-incidence. The Zynq PS support a range of crystal freqs so the
hardcoded setting should be removed from the dtsi. Re-implement it
on the board level.
This prepares support for Zynq boards with different crystal
frequencies (e.g. the Digilent ZYBO).
Acked-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The SDMMC, SDIO and EMMC controllers use an external FIFO whose size is 256x32bit.
This patch set the corresponding fifo-depth properties for both RK3066 and RK3188.
Signed-off-by: Julien CHAUVEAU <julien.chauveau@neo-technologies.fr>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The leds-gpio driver recently switched to the device property API. The device_node
name is no longer retrieved if the "label" devicetree property is not found.
In this case the driver tries to create entries with (null) name in
/sys/class/leds, which is wrong and generates backtrace as several gpio_leds have
the same name. Also renamed subnode "yellow" to "blue" to match the last
schematics updates.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The suspend/resume sequence on Armada XP needs to modify a number of
registers in the SDRAM controller. Therefore, this commit updates the
Armada XP Device Tree description to include the SDRAM controller
Device Tree node.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/1416585613-2113-17-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
In order to support suspend/resume on Armada XP, an additional set of
registers need to be described at the MBus controller level. This
commit therefore adjusts the Device Tree of the Armada 370/XP SoC to
include those registers in the MBus controller description;
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/1416585613-2113-16-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commit improves the Armada XP GP Device Tree description to
describe the 3 GPIOs that are used to connect the SoC to the PIC
micro-controller that we talk to shutdown the SoC when entering
suspend to RAM.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/1416585613-2113-15-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The most important part is adding the axi bus to the SoC dtsi file,
this is the main bus on the SoC.
These patches were all send to the arm list and I haven't got any
negative responses.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJUd5jfAAoJEIZ0px9YPRMyQDgP/3EKRthup3LVF0K5Y/z256Xm
95F7fjrQSAeo47WXL5YkZPhFh2Brs0tcmR/Xt9J+sm4jRUMDgaa0DIH0R1FD6R/z
j7J2mLQ+NORMQg2A0gtJPJg+o/PMi9+jZ2I3D6dyewaQOemEbs7dej7INzRQWxik
8gKjIlPm0yKIcFnkLOg6W6++GseCM4DiP2714l6SM+W4hExZUQuVqW7yNR3Y2jPt
h3omY+kWUHIhjN7iOCvoF70x89d0pgYl6u9BIjda63a9flpiAUs7+0to1dgsSn3i
QWgIB0rxVPDrtW2TYmzxKNQgRlzKJzyzowlf+uqgE48Z9CwFlwirCIa6D8bOP27G
hJ7E7FgZZdKGI7W0OB2wru7jNLgwuVVursMh0ef7T1vQXJjZGqqXdCLQWx4i/XoW
PIPTvEwr37/oI8Zx9yxPW4jxKOmDK9lW17DR1JIn4C8QWMvWJ3/wcgUCpblWhY0k
yrtenOWc83NDcrcufonhr293lBuLi9gCZel58rkj3GP02/MijkcDSslVSCgO0nH8
YLQcTzU66vnwWAhVZXp5X0BJtkAvmbxXXkKqJxa1nGMpr8aF7QHKPFZPmRqzhnHG
JKLdANoaPygJjHACgkPjvUetIdv95Pq4CRXppsqcnm7tzu6nn2LBRRxHQiXvVlyJ
7neCvZGAtQz/WpBSHriX
=oMPU
-----END PGP SIGNATURE-----
Merge tag 'bcm5301x-dt-2014-11-27' of https://github.com/hauke/linux into next/dt
Pull "ARM: BCM5301X: Add some more devices to device tree" from Hauke Mehrtens:
The most important part is adding the axi bus to the SoC dtsi file,
this is the main bus on the SoC.
These patches were all send to the arm list and I haven't got any
negative responses.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* tag 'bcm5301x-dt-2014-11-27' of https://github.com/hauke/linux:
ARM: BCM5301X: Add LEDs for Netgear R6250 V1
ARM: BCM5301X: Add Broadcom's bus-axi to the DTS file
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- mvebu
- Use simple-card audio on Armada 370 DB
- Add DSA node for Armada 370 DB
- Add SDHCI to Armada 38x
- Armada 370/XP rework to support new Synology boards
- Add Synology DS213j and DS414
- Various pinctrl and uart and alias fixes to help bootloaders
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=F5lu
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-3.19-2' of git://git.infradead.org/linux-mvebu into next/dt
Pull "mvebu DT changes for v3.19 (round 2)" from Jason Cooper:
- mvebu
- Use simple-card audio on Armada 370 DB
- Add DSA node for Armada 370 DB
- Add SDHCI to Armada 38x
- Armada 370/XP rework to support new Synology boards
- Add Synology DS213j and DS414
- Various pinctrl and uart and alias fixes to help bootloaders
* tag 'mvebu-dt-3.19-2' of git://git.infradead.org/linux-mvebu:
arm: mvebu: normalize pinctrl entries for Armada SoCs
arm: mvebu: fix wrongly named DS414 pinctrl entries
arm: mvebu: add .dts file for Synology DS414
arm: mvebu: add .dts file for Synology DS213j
arm: mvebu: define and use common Armada XP SPI pinctrl setting
arm: mvebu: define and use common Armada XP UART2/3 pinctrl settings
arm: mvebu: define and use common Armada 370 UART pinctrl settings
arm: mvebu: define and use common Armada 370 SPI pinctrl settings
arm: mvebu: move Armada 370/XP pinctrl node definition armada-370-xp.dtsi
arm: mvebu: use recently introduced uart label for stdout-path
arm: mvebu: add uartX labels for Armada SoC serial nodes
arm: mvebu: fix vendor prefix typo in kirkwood-synology.dtsi
ARM: mvebu: fix ordering in Armada 370 .dtsi
ARM: mvebu: adjust ethernet aliases according to U-Boot requirements for A38x
ARM: mvebu: remove clock-frequency from Armada 38x SDHCI Device Tree node
ARM: mvebu: enable no-1-8-v flag for Armada 385 DB SDHCI interface
mvebu: 370 RD: Add support for the switch
ARM: mvebu: use simple-card DT binding for audio on Armada 370 DB
ARM: mvebu: remove conflicting muxing on Armada 370 DB
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This enables the simple framebuffer on all the supported Allwinner SoCs (but
the A80). That allows to have at last a video display usable by using the
framebuffer the firmware might have set up.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Rgt0
-----END PGP SIGNATURE-----
Merge tag 'sunxi-simplefb-for-3.19' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Pull "Allwinner simple frambuffer support" from Maxime Ripard:
This enables the simple framebuffer on all the supported Allwinner SoCs (but
the A80). That allows to have at last a video display usable by using the
framebuffer the firmware might have set up.
* tag 'sunxi-simplefb-for-3.19' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (55 commits)
ARM: dts: sunxi: Update simplefb nodes so that u-boot can find them
ARM: dts: sunxi: Add de_be0 clk parent pll to simplefb node
ARM: dts: sun7i: Add simplefb node
ARM: dts: sun6i: Add simplefb node
ARM: dts: sun5i: Add simplefb node
ARM: dts: sun4i: Add simplefb node
ARM: dts: sun6i: Add ethernet support to M9 board
ARM: sun6i: DT: Add PLL6 multiple outputs
ARM: dts: sun6i: Add support for the status led
ARM: dts: sun6i: Add EHCI support for the M9 board
ARM: dts: sunxi: Add regulator-boot-on property to ahci-5v regulator
ARM: dts: sun7i: Cubietruck: add power supply regulator for USB OTG VBUS
ARM: dts: sun7i: Cubietruck: override regulator pin
ARM: sun7i: dtsi: add support for usbphy0
ARM: dtsi: sunxi: add common VBUS regulator
ARM: dts: sunxi: Banana Pi: increase startup-delay for the GMAC PHY regulator
ARM: sun5i: olinuxino: Relicense the device tree under GPLv2/X11
ARM: sun4i: cubieboard: Relicense the device tree under GPLv2/X11
ARM: sun7i: pcduino3: Relicense the device tree under GPLv2/X11
ARM: sun4i: pcduino: Relicense the device tree under GPLv2/X11
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Device additions for board vf610-colibri, pwm, backlight, I2C, RTC,
ADC etc.
- Update i.MX6 phyFLEX board to include PCIe, CAN and audio support
- Improve SSI clocks description for i.MX5 platforms
- Add ENET2 support for imx6sx-sdb board
- Add device tree source for LS1021A SoC, board QDS and TWR
- Enable cpufreq support for i.MX53
- Enable VPU device support for i.MX6QDL
- Enable poweroff support for i.MX6 SoCs
- Add support for TBS2910 Matrix ARM mini PC which is built on i.MX6Q
- Create generic base device trees for Vybrid and add support for
Colibri VF50
Note: the change set is built on top of imx-soc-3.19 to resolve the
dependency that "ARM: dts: imx53: add cpufreq-dt support" uses the
clock define IMX5_CLK_ARM that is added by "ARM: imx53: clk: add ARM
clock".
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUcZicAAoJEFBXWFqHsHzO0ooH/ie5r7JDjklD6IlAxD9UyDyp
RQSF/8VYTc1EhECI5D/xmHARnUM5AxfMBQzFyavz/0hkGp22xJtBgp5ZlYtWwyAF
qpLI031/5hn+37NyMxdcd6nU55e7GJw4loBXTZ5pNSRdP+ubsUVccfUdQ1K5hPA6
KeS5vqaX26c5P2R+tkx2pfRLmCrSWNKNIpIbZzenlu2dS7U77ex1AO2W+ToDTgQ3
asVIMD/7oQ4soEGZfSQdzHCftQ2OdVGlybFoMCkW5xrzRVfucbSN2BbLpEM5Z117
/DZpfAmHlT4NrGz/BBzpK6l3AWFmXLmCP/dFvvfzKM3uWgr/zlVF8ChW/xgCc+g=
=FnNq
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
Pull "The i.MX device tree changes for 3.19" from Shawn Guo:
- Device additions for board vf610-colibri, pwm, backlight, I2C, RTC,
ADC etc.
- Update i.MX6 phyFLEX board to include PCIe, CAN and audio support
- Improve SSI clocks description for i.MX5 platforms
- Add ENET2 support for imx6sx-sdb board
- Add device tree source for LS1021A SoC, board QDS and TWR
- Enable cpufreq support for i.MX53
- Enable VPU device support for i.MX6QDL
- Enable poweroff support for i.MX6 SoCs
- Add support for TBS2910 Matrix ARM mini PC which is built on i.MX6Q
- Create generic base device trees for Vybrid and add support for
Colibri VF50
Note: the change set is built on top of imx-soc-3.19 to resolve the
dependency that "ARM: dts: imx53: add cpufreq-dt support" uses the
clock define IMX5_CLK_ARM that is added by "ARM: imx53: clk: add ARM
clock".
* tag 'imx-dt-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (51 commits)
ARM: dts: imx6q-tbs2910: Enable snvs-poweroff
ARM: dts: imx6: add pm_power_off support for i.mx6 chips
ARM: dts: vf-colibri: add USB regulators
ARM: dts: imx6: phyFLEX: Add CAN support
ARM: dts: imx6: phyFLEX: Add PCIe
ARM: dts: imx6: phyFLEX: Set correct interrupt for pmic
ARM: dts: imx6: phyFLEX: Enable gpmi in module file
ARM: dts: imx6: phyFLEX: set nodes in alphabetical order
ARM: dts: vf-colibri-eval-v3.dts: Enable ST-M41T0M6 RTC
ARM: dts: vf-colibri: Add I2C support
ARM: dts: imx6qdl: Enable CODA960 VPU
ARM: dts: imx6q-tbs2910: Remove unneeded 'fsl,mode' property
ARM: dts: vf610: enable USB misc/phy nodes where necessary
ARM: dts: vf610: use new GPIO support
ARM: dts: pbab01: enable I2S audio on phyFLEX-i.MX6 boards
ARM: dts: pbab01: move i2c pins and frequency configuration into pfla02
ARM: dts: vf500-colibri: add Colibri VF50 support
ARM: dts: vf610: create generic base device trees
ARM: dts: vf610: assign oscillator to clock module
dt-bindings: arm: add Freescale LS1021A SoC device tree binding
...
Signed-off-by; Arnd Bergmann <arnd@arndb.de>
- Clean up reset handler for DT machines, since reset has been handled
in watchdog driver
- Remove unneeded .map_io hook for a couple of i.MX6 machines
- A few small i.MX6 device tree source cleanups
- Some random iomuxc and pllv3 code cleanup
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUcYNdAAoJEFBXWFqHsHzOhJUH/i2Ssq8yJb7rSkjGBvytZQhW
b9JdPrGBZmeh0247brB5FB4EzDg3p8o+/v7tNPofP6RwbJXCsWQaLwNRNwTdL+mv
KoKboCnIBB9OdGQw7IWZ2tKjmP4msmXbTbX/+Rf/f6sukd9VL/lxK7An3iVNmlJw
gD2y9Ryul0xBkxajvM6JduBwpTVnjCSzpOWGB+GjpUiMPqm5li1qmyKaQc1Vh7Dm
fbr0ZWgj+NaJkuOAQ5rL4HtJs/bzoLjTkTAnehoTrt9bVWOySy7LQVG2CsHmT2eD
2jzjVUC7NcBHbubs9HhK5kCnASE2Lr7u3JnSNpjAxWpHM9e0tYo4+PiW1pZX11k=
=+FHh
-----END PGP SIGNATURE-----
Merge tag 'imx-cleanup-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/cleanup
Pull "The i.MX cleanup for 3.19" from Shawn Guo:
- Clean up reset handler for DT machines, since reset has been handled
in watchdog driver
- Remove unneeded .map_io hook for a couple of i.MX6 machines
- A few small i.MX6 device tree source cleanups
- Some random iomuxc and pllv3 code cleanup
* tag 'imx-cleanup-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx: Remove unneeded .map_io initialization
ARM: dts: imx6qdl-sabresd: Fix the microphone route
ARM: imx: refactor mxc_iomux_mode()
ARM: imx: simplify clk_pllv3_prepare()
ARM: imx6q: drop unnecessary semicolon
ARM: imx: clean up machine mxc_arch_reset_init_dt reset init
ARM: dts: imx6qdl-rex: Remove unneeded 'fsl,mode' property
ARM: dts: imx6qdl-gw5x: Remove unneeded 'fsl,mode' property
ARM: dts: imx6qdl-sabresd: Use IMX6QDL_CLK_CKO define
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
SoC related changes for omaps including hwmod clean-up for
DSS, and hwmod data for more UARTs and ADC. Also few defconfig
changes to enable devices found on am335x and am437x.
[arnd: I removed the defconfig changes from the branch in order
to cherry-pick them onto the next/defconfig branch, but I did
not change the other commits]
* commit '29c4ce17bcad':
ARM: dts: cm-t3x30: add keypad support
ARM: OMAP2+: hwmod: AM43x: add hwmod support for ADC on AM43xx
ARM: DRA7: hwmod data: Add missing UART hwmod data
ARM: dts: omap4.dtsi: remove dss_fck
ARM: OMAP4: fix RFBI iclk
ARM: OMAP4: hwmod: use MODULEMODE properly
ARM: OMAP4: hwmod: set DSS submodule parent hwmods
ARM: OMAP5: hwmod: set DSS submodule parent hwmods
ARM: OMAP2+: hwmod: add parent_hwmod support
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
run again, until the patches for using the physical architected
timers got accepted.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJUcK60AAoJEPOmecmc0R2BPqYH/202nLDZaBuY3ZaXIoRUNZx4
s5oPQWmJ9xSW4K93tnAtrQ3YP9NE4SrSSAKIszeY7sNI0XapdFrT8ARinh3bA8Ir
cCr0iXMGHwpWF9K9nfYM8z+fNIwVOa2KktbmZi9tgOvxfOFkadRXoBj6gdxwN8oO
2UTgbB7iD2F0FRTj+kmrxTML+vkW8LyladQIoyyeCwoFCkUYoPerLpuwvnPEujoO
aN3eot9w7uqP28NwsD9nC5Ns+mzICF9ts3IRCyv1zoGkXpA+7meHvNvtrOW2v3JJ
xdUh8bvCwSMrb0jh07PDfSFMkOZlfNIl8eXUZrxx66ss8VDMCXwVaxLS7llxdCk=
=gBaE
-----END PGP SIGNATURE-----
Merge tag 'v3.19-rockchip-dts3' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Pull "temporarily disable rk3288-smp" from Heiko Stuebner:
Disable smp again on rk3288 temporarily to make Olof's boottest
run again, until the patches for using the physical architected
timers got accepted.
* tag 'v3.19-rockchip-dts3' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: temporarily disable smp on rk3288
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This has been successfully tested on Netgear R6250 and two other
development (unnamed) devices, all of them BCM4708 based.
We also got a possitive feedback from R7000 (BCM4709) tester.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
- explicitly set dr_mode on exynos5250-snow
this is required when kernel is built with USB gadget support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=R/UY
-----END PGP SIGNATURE-----
Merge tag 'samsung-fixes-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Pull "Samsung fixes for v3.18" from Kukjin Kim:
- explicitly set dr_mode on exynos5250-snow
this is required when kernel is built with USB gadget support.
* tag 'samsung-fixes-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Explicitly set dr_mode on exynos5250-snow
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adds syscon based phandle to i2c device nodes of exynos5250
and exynos5420. These phandles will be used to save restore i2c sysreg
configuration register during s2r from i2c driver.
CC: Rob Herring <robh+dt@kernel.org>
CC: Randy Dunlap <rdunlap@infradead.org>
CC: Russell King <linux@arm.linux.org.uk>
CC: devicetree@vger.kernel.org
CC: linux-doc@vger.kernel.org
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch removes unused dt node of command line from Exynos3250-based
Rinato board because kernel use the command line from bootloader.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds new board dts file to support Samsung Monk board which
is based on Exynos3250 SoC and has different H/W configuration from
Rinato.
This dts file support following features:
- eMMC
- Main PMIC (Samsung S2MPS14)
- Interface PMIC (Maxim MAX77836, MUIC, fuel-gauge, charger)
- RTC of Exynos3250
- ADC of Exynos3250 with NTC thermistor
- I2S of Exynos3250
- TMU of Exynos3250
- Secure firmware for Exynos3250 secondary cpu boot
- Serial ports of Exynos3250
- gpio-key for power key
Signed-off-by: Youngjun Cho <yj44.cho@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
There are currently 2 differents naming conventions used between the
existing Armada SoC DT files for pinctrl entries (*_pin(s): *-pin(s)
and pmx_*: pmx-*) with a vast majority of files using the former:
$ grep _pin arch/arm/boot/dts/armada-*.dts* | wc -l
155
$ grep pmx arch/arm/boot/dts/armada-*.dts* | wc -l
13
In fact, only some Armada XP files are using the second variant.
This patch normalizes those files (mainly ge0/1 entries) to use
the first variant.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Link: https://lkml.kernel.org/r/00114c3169e1d93259ff4150ed46ee36eae16b1e.1416670812.git.arno@natisbad.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
While renaming pinctrl entries during reviews of Synology DS414 support
series, I missed three entries, as reported by Ben. This patch fixes
those.
Reported-by: Ben Peddell <klightspeed@killerwolves.net>
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Link: https://lkml.kernel.org/r/608e4fd6e06e9c5289a84b9c38e81b2456dbcd79.1416670812.git.arno@natisbad.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
this patch adds missed resets property for CSR SiRFatlasVI SPI nodes.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
