When the RIC data element (RDE) is included in the IEs coming
from userspace for an association request, its handling is
currently broken as any IEs that are contained within it would
be split off from it and inserted again after all the IEs that
mac80211 generates (e.g. HT, VHT.)
To fix this, treat the RIC element specially, and stop after
it only when we find something that doesn't actually belong to
it. This assumes userspace is actually correctly building it,
directly after the fast BSS transition IE and before all the
others like extended capabilities.
This leaves as a potential problem the case where userspace is
building the following IEs:
[RDE] [vendor resource description] [vendor non-resource IE]
In this case, we'd erroneously consider all three IEs to be
part of the RIC data together, and not split them between the
two vendor IEs. Unfortunately, it isn't easily possible to
distinguish vendor IEs, so this isn't easy to fix. Luckily,
this case is rare as normally wpa_supplicant will include an
extended capabilities IE in the IEs, and that certainly will
break the two vendor IEs apart correctly.
Reviewed-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds 802.11p OCB (Outside the Context of a BSS) mode
support.
When communicating in OCB mode a mandatory wildcard BSSID
(48 '1' bits) is used.
The EDCA parameters handling function was changed to support
802.11p specific values.
The insertion of a newly discovered STAs is done in the similar way
as in the IBSS mode -- through the deferred insertion.
The OCB mode uses a periodic 'housekeeping task' for expiration of
disconnected STAs (in the similar manner as in the MESH mode).
New Kconfig option for verbose OCB debugging outputs is added.
Signed-off-by: Rostislav Lisovy <rostislav.lisovy@fel.cvut.cz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds new iface type (NL80211_IFTYPE_OCB) representing
the OCB (Outside the Context of a BSS) mode.
When establishing a connection to the network a cfg80211_join_ocb
function is called (particular nl80211_command is added as well).
A mandatory parameters during the ocb_join operation are 'center
frequency' and 'channel width (5/10 MHz)'.
Changes done in mac80211 are minimal possible required to avoid
many warnings (warning: enumeration value 'NL80211_IFTYPE_OCB'
not handled in switch) during compilation. Full functionality
(where needed) is added in the following patch.
Signed-off-by: Rostislav Lisovy <rostislav.lisovy@fel.cvut.cz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The configured tx power is often limited by hardware capabilities,
channel settings, antenna configuration, etc.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[fix tracing compilation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Maximum length of AMPDU that an STA can receive in VHT.
length = 2 ^ (13 + max_ampdu_length_exp) - 1.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Yaogong replaces TCP out of order receive queue by an RB tree.
As netem already does a private skb->{next/prev/tstamp} union
with a 'struct rb_node', lets do this in a cleaner way.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yaogong Wang <wygivan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-11-03
This series contains updates to i40e and i40evf.
Akeem adds a check for i40e so that flow director flush and reinit are
not done when flow director is not enabled.
Mitch fixes the i40evf driver to properly handle multiple admin queue
messages, by reinit the msg_size field each time we go through the loop.
Without this, we may receive truncated messages due to the firmware
thinking we have insufficient buffer size. Also fixes the link checking
logic to only check the carrier state if the interface is actually
open, which allows link changes to be reported correctly without spamming
the VFs. Updates i40e to inset the VSI ID in the QTX_CTL register
when configuring queues for VMDq VSIs.
Paul adds support for 10G-base-T in i40evf.
Jesse fixes i40e where the call to irq_dynamic_disable() was turning off
the interrupt completely when trying to set ITR to 0 (for lowest
moderation).
Shannon removes debugfs dump stats function, since it was not being
kept up-to-date and was redundant with the ethtool output. Also, scales
back the LAN MSIx usage to force queue/vector sharing and leave some
vectors for Flow Director, VMDq, etc. when there are more cores than
vectors available to the PF. Cleans up the error reporting for
get_lump() resource tracking errors. Also adds a check for the
debug module parameter earlier to be able to catch the early configuration
phase admin queue messages.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
efx_ef10_probe() was BUGging out if the BAR2 size was 0. This is
unnecessarily violent; instead we should just fail to probe the device.
Kept a WARN_ON as this problem indicates a broken or misconfigured NIC.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
ipv6: Fix iflink setting for ipv6 tunnels
The ipv6 tunnels do the dev->iflink setting too early, it gets
overwritten by register_netdev(). So set dev->iflink from within
a ndo_init function to keep the configured setting.
This patchset fixes this for ip6_tunnel, vti6, sit and gre6.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise it gets overwritten by register_netdev().
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipip6_tunnel_init() sets the dev->iflink via a call to
ipip6_tunnel_bind_dev(). After that, register_netdevice()
sets dev->iflink = -1. So we loose the iflink configuration
for ipv6 tunnels. Fix this by using ipip6_tunnel_init() as the
ndo_init function. Then ipip6_tunnel_init() is called after
dev->iflink is set to -1 from register_netdevice().
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vti6_dev_init() sets the dev->iflink via a call to
vti6_link_config(). After that, register_netdevice()
sets dev->iflink = -1. So we loose the iflink configuration
for vti6 tunnels. Fix this by using vti6_dev_init() as the
ndo_init function. Then vti6_dev_init() is called after
dev->iflink is set to -1 from register_netdevice().
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_tnl_dev_init() sets the dev->iflink via a call to
ip6_tnl_link_config(). After that, register_netdevice()
sets dev->iflink = -1. So we loose the iflink configuration
for ipv6 tunnels. Fix this by using ip6_tnl_dev_init() as the
ndo_init function. Then ip6_tnl_dev_init() is called after
dev->iflink is set to -1 from register_netdevice().
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this is check for dev is unnecessary, as we are already checking dev
after allocating it via alloc_netdev, and jumping to label: out
if it is NULL.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VLAN is in use in macvtap_put_user, we end up setting
csum_start to the wrong place. The result is that the whoever
ends up doing the checksum setting will corrupt the packet instead
of writing the checksum to the expected location, usually this
means writing the checksum with an offset of -4.
This patch fixes this by adjusting csum_start when VLAN tags are
detected.
Fixes: f09e2249c4 ("macvtap: restore vlan header on user read")
Cc: stable@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Cheers,
Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu says:
====================
tun: Fix csum_start and TUN_PKT_STRIP
The first patch fixes a serious problem that breaks checksum offload
in VMs while the second patch fixes a problem that probably affects
no one.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We set the flag TUN_PKT_STRIP if the user buffer provided is too
small to contain the entire packet plus meta-data. However, this
has been broken ever since we added GSO meta-data. VLAN acceleration
also has the same problem.
This patch fixes this by taking both into account when setting the
TUN_PKT_STRIP flag.
The fact that this has been broken for six years without anyone
realising means that nobody actually uses this flag.
Fixes: f43798c276 ("tun: Allow GSO using virtio_net_hdr")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VLAN acceleration is in use on the xmit path, we end up
setting csum_start to the wrong place. The result is that the
whoever ends up doing the checksum setting will corrupt the packet
instead of writing the checksum to the expected location, usually
this means writing the checksum with an offset of -4.
This patch fixes this by adjusting csum_start when VLAN acceleration
is detected.
Fixes: 6680ec68ef ("tuntap: hardware vlan tx support")
Cc: stable@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The makefile for sanitizing kernel headers uses the kbuild file
to determine which files to do. Several networking related headers
were missing. Without these headers iproute2 build would break.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz says:
====================
Mellanox ethernet driver update Oct-30-2014
The 1st patch from Saeed fixes a bug in the last net-next batch where
a VF could get access to set port configuration, the next patch from Amir
fixes a race in the port VPI logic. Next are two performance patches from Ido.
The patch to add checksum complete status on GRE and such packets was
preceded with a patch that converted the driver to only use napi_gro_receive
vs. the current code which goes through napi_gro_frags on it's usual track.
Eric D. has some thoughts and suggestions on that change for which we
want to take the time and consider, so for the time being dropped that
patch and the ones that depend on it.
Changes from V0:
- have the caller to provide the __GFP_COLD hint to the service function
- dropped the patch that changes the GRO logic and the subsequent dependent
patches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add code to issue CONFIG_DEV "get" firmware command.
This command is used in order to obtain certain parameters used for
supporting various RX checksumming options and vxlan UDP port.
The GET operation is allowed for VFs too.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Needed in order to get cache cold pages (L3 flushed) for HW scatter.
Otherwise memory may flush those entries when the packet comes from
PCI, causing back pressure resulting in BW decrease.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When IP_ALIGN has a non zero value, hardware will write to a non aligned
address. The only reader from this address is when copying the header
from the first frag into the linear buffer (further access to the IP
address will be from the linear buffer, in which the headers are
aligned). Since the penalty of non align access by the hardware is
greater than the software memcpy, changing the frag_align to always be 0.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to protect set_port_type() for concurrency, as the sysfs code could
call it from mutliple contexts in parallel.
The port_mutex is not enough because we need to protect from concurrent
modification of 'info' and stopping of the port sensing work.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added wrapper to the ACCESS_REG command for handling guest HW
registers access, preventing write operations, but do allow reads.
This will prevent SRIOV guests to change port PTYS configuration,
such as speed/advertised link modes.
Fixes: adbc7ac5c1 ('net/mlx4_core: Introduce ACCESS_REG CMD [...]')
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net_rx_action() can mask irqs a single time to transfert sd->poll_list
into a private list, for a very short duration.
Then, napi_complete() can avoid masking irqs again,
and net_rx_action() only needs to mask irq again in slow path.
This patch removes 2 couples of irq mask/unmask per typical NAPI run,
more if multiple napi were triggered.
Note this also allows to give control back to caller (do_softirq())
more often, so that other softirq handlers can be called a bit earlier,
or ksoftirqd can be wakeup earlier under pressure.
This was developed while testing an alternative to RX interrupt
mitigation to reduce latencies while keeping or improving GRO
aggregation on fast NIC.
Idea is to test napi->gro_list at the end of a napi->poll() and
reschedule one NAPI poll, but after servicing a full round of
softirqs (timers, TX, rcu, ...). This will be allowed only if softirq
is currently serviced by idle task or ksoftirqd, and resched not needed.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
flow_limit in struct softnet_data is only read from local cpu
and can be moved to fill a hole, reducing softnet_data size by
64 bytes on x86_64
While we are at it, move output_queue, output_queue_tailp and
completion_queue, so that rx / tx paths touch a single cache line.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix:
net/bridge/netfilter/nft_reject_bridge.c:
In function 'nft_reject_br_send_v6_unreach':
net/bridge/netfilter/nft_reject_bridge.c:240:3:
error: implicit declaration of function 'csum_ipv6_magic'
csum_ipv6_magic(&nip6h->saddr, &nip6h->daddr,
^
make[3]: *** [net/bridge/netfilter/nft_reject_bridge.o] Error 1
Seen with powerpc:allmodconfig.
Fixes: 523b929d54 ("netfilter: nft_reject_bridge: don't use IP stack to reject traffic")
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a few problems with our parsing of the MDET registers:
* Queue IDs are longer than 8 bits
* Queue IDs are absolute for the device and the base queue must be
subtracted out.
* VF IDs are longer than 8 bits
* Use the MASK define to mask the event value, instead of the SHIFT
define.
Change-ID: I3dc7237f480c02e1192a2a8ea782f8a02ab2a8b7
Reported-by: Marc Neustadter <marc.neustadter@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We must insert the VSI ID in the QTX_CTL register when
configuring queues for VMDQ VSIs.
Change-ID: Iedfe36bd42ca0adc90a7cc2b7cf04795a98f4761
Reported-by: Marc Neustadter <marc.neustadter@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Check the debug module parameter earlier to be able to catch the early
configuration phase adminq messages.
Change-ID: Ic84fabd72393489bbf96042de770790a80fd8468
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tweak and homogenize the error reporting for get_lump() resource
tracking errors.
Change-ID: I11330161cc6ad8d04371c499c63071c816171c3b
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When there are more cores than vectors available to the PF, scale back
the LAN msix usage to force queue/vector sharing and leave some vectors
for Flow Director, VMDq, etc.
Change-ID: Ie0317732eb85ad8d851d7da7d9af86b1bf8c21ad
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The debugfs dump stats wasn't being kept up-to-date, was redundant with
the ethtool output, and didn't offer any useful additional info. Rather
than continue trying to keep them aligned, just remove the debugfs command.
Change-ID: Id130ed9aef01c6369ab662c7b4c5ec5b1dbc5b40
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <Jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The call to irq_dynamic_disable was turning off the interrupt completely
when trying to set ITR to 0 (for lowest moderation). Just remove the
call as setting the values to 0 later in this function will suffice.
Change-ID: I47caf1ecbe65653cf63ec833db93094cd83fd84d
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-By: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add 10G-Base-T support in i40evf.
Change-ID: I98a1c3138d7d6572fe7903a7c1c4692cae3260d5
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the interface is closed, but VFs exist, current code will spam all
the VFs with link messages every second. This is because the link event
code was looking at netif_carrier_ok() without checking to see if the
interface was actually open.
Refactor the logic to only check the carrier state if the interface is
actually open. This allows link changes to be reported correctly without
spamming the VFs.
Change-ID: If136e79bb3820d21ea4e39e332e8a9604efc2b2a
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When we receive an admin queue message, the msg_size field in the event
struct gets overwritten. Because of this, we need to reinit the field
each time we go through the loop. Without this we may receive truncated
messages due to the firmware thinking we have insufficient buffer size.
Change-ID: I21dcca5114d91365d731169965ce3ffec0e4a190
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When FD_SB/ATR are not enabled, do not allow flow director flush
and reinit.
Change-ID: Iafe261c1862992981615815551abd1ed9fada0a8
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The SMC91x is written to explicitly look up the IRQ resource
from the platform device and extract the IRQ and flags, however
the platform_get_irq() does additional things, like call
of_irq_get() in the device tree case, which will translate
the IRQ using the irqdomain and defer the probe if the
IRQ host cannot be found.
As we're not looking up the resource, this will not retrieve
the IRQ flags, but that is better done using
irqd_get_trigger_type(), as the trigger is what the driver
wants to modify. We take care to preserve the semantics that
will make the trigger type provided from the resource
override any local specifier.
Tested on the Nomadik NHK15 which has its SMC91x IRQ line
connected to a STMPE2401 GPIO expander on I2C.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When use current latest upstream qemu (current version: 2.1.2), need let
driver compatible with 'xlnx,xps-ethernetlite-2.00.b', or can not find
net device in microblaze qemu. Related QEMU commands under fedora 20:
yum install libvirt
yum install tunctl
tunctl -b
ip link set tap0 up
brctl addif virbr0 tap0
./microblaze-softmmu/qemu-system-microblaze -M petalogix-s3adsp1800 \
-kernel ../linux-stable.microblaze/arch/microblaze/boot/linux.bin \
-no-reboot -append "console=ttyUL0,115200 doreboot" -nographic \
-net nic,vlan=0,model=xlnx.xps-ethernetlite,macaddr=00:16:35:AF:94:00 \
-net tap,vlan=0,ifname=tap0,script=no,downscript=no
in microblaze qemu bash (guest machine):
ifconfig eth0 add 192.168.122.2 netmask 255.255.255.0
ifconfig eth0 up
After add this patch, can find the device, and can be used by 'telnetd'
(need cross-build busybox with glibc for it), then outside can telnet to
it without password.
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
net: systemport: TX dma fixes
This patch series contains two fixes for our transmit path, first one
is a pretty nasty one since we were not allocating a large enough
dma coherent pool for our transmit descriptors, which would work most of the
time, since allocations are contiguous and we could have.
Second patch fixes a less frequent, though highly likley crash when using
CMA allocations.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Callers of bcm_sysport_init_tx_ring() can currently fail, and will
always call bcm_sysport_fini_tx_ring() in a loop ending at the number of
TX queues (32) without checking if the TX ring was successfully
initialized or not.
Update bcm_sysport_fini_tx_ring() to return early and avoid a crash
de-referencing ring->cbs if the TX ring was not initialized, since
ring->cbs is the last part of the initialization done by
bcm_sysport_init_tx_ring() that could fail.
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should not be allocating a single byte of DMA coherent memory, but
instead a full-sized struct dma_desc (8 bytes).
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
we are allocating memory using kzalloc for struct mvpp2_prs_entry,
but later when we are getting error we were just returning the error
value without releasing the memory.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull input updates from Dmitry Torokhov:
"A bunch of fixes for minor defects reported by Coverity, a few driver
fixups and revert of i8042.nomux change so that we are once again
enable active MUX mode if box claims to support it"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: i8042 - disable active multiplexing by default"
Input: altera_ps2 - use correct type for irq return value
Input: altera_ps2 - write to correct register when disabling interrupts
Input: max77693-haptic - fix potential overflow
Input: psmouse - remove unneeded check in psmouse_reconnect()
Input: vsxxxaa - fix code dropping bytes from queue
Input: ims-pcu - fix dead code in ims_pcu_ofn_reg_addr_store()
Input: opencores-kbd - fix error handling
Input: wm97xx - adapt parameters to tosa touchscreen.
Input: i8042 - quirks for Fujitsu Lifebook A544 and Lifebook AH544
Input: stmpe-keypad - fix valid key line bitmask
Input: soc_button_array - update calls to gpiod_get*()
