As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The stream is created whilst the compressed stream is opened and a
buffer is created when the DSP powers up. It is necessary at a point
once both the DSP has powered up and the the stream has been opened to
connect a stream to a buffer on the DSP. This is done in the trigger
callback as this is after the DSP has been powered and obviously the
stream must be open. Note that whilst the connect is currently trivial
it is expected that this will get more complex when support for multiple
buffers/streams per DSP is added.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add code that locates and initialises the buffer of compressed data on
the DSP if the firmware supported compressed data capture. The buffer
struct (wm_adsp_compr_buf) is kept separate from the stream struct
(wm_adsp_compr) this will allow much easier support of multiple
streams of data from the one DSP in the future, although support for
this will not be added in this patch chain.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow user-space to open a compressed stream, although no data will be
passed yet, as part of this adding the ability to define supported
capabilities per firmware and check these match the stream being opened.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Register a platform driver for the CODEC and add DAIs that will be used
to connect a compressed record path for the voice control functionality.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
PLL mode based on 32KHz master clock not supported in
AB silicon so remove support from the driver.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
HW can provide 1.6V micbias level as well the existing levels
already provided in the driver. This patch adds support for 1.6V
to the DT binding.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In AB silicon, the internal LDO is not supported so remove
DT and driver references to this (digital voltage direct from
'VDD' supply)
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In current AB silicon, BIAS_EN field is enabled by default in the
REFERENCES register, so the regmap default value should reflect
this.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If codec probe() function fails after supplies have been enabled
it should really tidy up and disable them again. This patch updates
the probe function to do just that.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Previously Sidetone would operate only when capture to DAI was in
progress, due to DAPM path configuration. There is no reason why
this should not operate without DAI capture, so this patch updates
the DAPM path accordingly.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
fsl_ssi uses different stream names ("AC97 Playback" / "AC97 Capture")
in AC'97 mode so in this case fsl-asoc-card route map should
also be using them.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add 8kHz, 11.025kHz, 16kHz, 22.05kHz output sample rate support.
According referance menual, "Limited support for the case when
output sampling rates is between 8kHz and 30kHz. The limitation
is the supported ratio (Fsin/Fsout) range as between 1/24 to 8."
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sometimes the audio play can not be resumed after it is
suspended. Add snd_soc_pm_ops to execute power management
operations, then this issue is fixed.
Signed-off-by: Songjun Wu <songjun.wu@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add NULL test on call to devm_kzalloc.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x;
identifier fld;
@@
* x = devm_kzalloc(...);
... when != x == NULL
x->fld
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add NULL test on call to devm_kzalloc.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x;
identifier fld;
@@
* x = devm_kzalloc(...);
... when != x == NULL
x->fld
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add NULL test on call to devm_kzalloc.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x;
@@
* x = devm_kzalloc(...);
... when != x == NULL
*x
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The return type "unsigned int" was used by the ssm2518_lookup_mcs()
function even though it will eventually return a negative error code.
Improve this implementation detail by deletion of the type modifier then.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds Multi channel support on Renesas R-Car sound.
This patch is tested on Salvator-X board, but it can't use
Multi channel, because supported format is different between
codec chip and R-Car.
Thus, it was tested on board which doesn't mount codec chip,
with oscilloscope.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support to the codec driver to handle mic level
detect related IRQs, and report these to user-space using a uevent
variable.
The uevent variable string "EVENT=MIC_LEVEL_DETECT" is sent to
user-space, if the mic level detect feature is enabled, and the
audio captured at the chosen mic(s) is above a certain threshold.
User-space can then handle the event accordingly (e.g. process
audio capture stream).
This method was chosen over ALSA control notification for a couple
of reasons:
1) There's no requirement here for a control to read state from.
The event is the only thing that's required and of interest.
2) tinyalsa support for control notifications does not exist so on
platforms using this over alsa-lib there is a need to add code
to support this event handling.
Another possible option would be to use the standard Jack reporting
framework but this really does not fit for this kind of event.
Finally, use of the input device framework is not being encouraged,
due to difficulties in enabling apps to access input devices, so
this has also been avoided.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
An external amp (if any) is connected to the external outputs of the SoC
of course, rather then directly to the internal amp.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a device tree match table. This serves to make the driver's support
of device tree more explicit.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
AFE is actually allowed to be turn on before configuration of DAIs
since each DAI has its own enabling control. Turn on/off AFE in
runtime resume/suspend to avoid AFE being shut down when closing a DAI
while other DAIs are still active.
Signed-off-by: Koro Chen <koro.chen@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The upstreamed code modified the control names from Mute to
Switch without changing the logic. To get audio working the Switch
needs to be off which isn't aligned with normal ALSA conventions.
Inverting the logic now so that Switch Off means mute and Switch On
means active audio using the specific volume setting.
Signed-off-by: Sebastien Guiriec <sebastien.guiriec@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
the fields channels_min, channels_max, rate and formats are
irrelevant for compressed playback, they will depend on the
content. This was probably a copy-paste mistake to have
them in the first place
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add dai links to enable additional playback stream with deeper
buffer for lower power consumption.
The normal and DEEP_buffer streams are not mutually exclusive,
content will be mixed by the DSP.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add definitions for MERR_DPCM_DEEP_BUFFER AND PIPE_MEDIA3_IN
Add relevant cpu-dai and dai link names
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
All the functionality was merged in DPCM-based driver,
keep older driver to avoid breaking userspace but
tag it as unsupported/deprecated
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge DMI quirks for various machines such as Asus T100
and clean-up code
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
first renaming and reducing delta with byt-rt5640 code before
dmi-based quirks are enabled
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
initial cleanup to use same pins
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Using the hw_fixup function in order to overwrite the default SSP
setting for Audio DSP port connected to the codec. Instead of
TDM 4ch use I2S 2ch 24 bits.
Signed-off-by: Sebastien Guiriec <sebastien.guiriec@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When pipeline is deleted, set the pipeline state to invalid state.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds clean up routine to clear the stream registers and
calls this routine before setting up stream registers.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After several open/close sai test with ctrl+c, there will be
I/O error. The SAI can't work anymore, can't recover. There
will be no frame clock. With adding the software reset in
trigger stop, the issue can be fixed.
This is a hardware bug/errata and reset is the only option.
According to the reference manual, the software reset doesn't
reset any control register but only internal hardware logics
such as bit clock generator, status flags, and FIFO pointers.
(Our purpose is just to reset the clock generator while the
software reset is the only way to do that.)
Since slave mode doesn't use the clock generator, only apply
the reset procedure to the master mode.
For asynchronous mode, TX will not be reset when RX is still
running. In this case, i can't reproduce this issue.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver is using complex macro to parse DAI connection.
This patch adds new rsnd_parse_connect_common() and replace current
macro to it.
This is prepare for multi channel support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
TDM will use 6 or 8 slots on 1 SSI, and Multi channel will use
6 or 8 slots on few SSI (each SSI uses 2 slots).
Thus, this adds new slot control functions which can be prepare
for Multi channel support.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_get_slot_rdai() returns total slots (it returns 6 if total 6
channels) , and rsnd_get_slot_extend() returns extended SSI width
(it returns 8 if total 6 channels). This will be used on SSI multi
channel support too (It will return 2 if total 6 channels with 3 SSI).
But, it is using confusable naming.
This patch changes rsnd_get_slot_rdai() -> rsnd_get_slot(),
rsnd_get_slot_extend() -> rsnd_get_slot_width()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas sound driver is using rsnd_get_slot_runtime(), but
it is same as runtime->channels. This patch removes
rsnd_get_slot_runtime()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current SSI/SSIU are using rsnd_get_slot_runtime() to check TDM,
but using rsnd_get_slot_extend() is more sane.
This patch fix it up
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It can't output corrent dma name *before* rsnd_mod_init().
It goes to *after* rsnd_mod_init() by this patch
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound driver has rsnd_get_adinr_bit/chan() functions.
It is assuming _bit() returns ADINR :: OTBL,
and _chan() returns ADINR :: CHNUM.
Current _bit() returns both OTBL and CHNUM. This patch fixup it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSIU should be controlled after SSI. This patch fix up it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This machine supports HDMI/DP ports so add these ports and its FE and BE
DAIlinks
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We have WOV module which should act as DAPM sink, so add that and
its links.
Also rename the refcap to "Wake On Voice" as some user expect to
find this name
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We have specific constraints for FE device (48KHz, stereo, 16
bits) and fixups for BE DMIC links (2 or 4 ch), so add those.
Also add one more FE DAIlink for dmiccap
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We don't support ignore suspend on few devices so remove that.
Also since we support ignore susend on PDM DMIC, add that
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAPM map for DMIC and SSP was not properly done, so fix that up.
Also mark machine as fully routed
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds Skylake I2S machine driver which uses NAU88L25 as anlog codec and
MAX98357A as speakers
Signed-off-by: Rohit Ainapure <rohit.m.ainapure@intel.com>
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the NAU88L25 + MAX98357A machine driver entry into
the machine table
Signed-off-by: Rohit Ainapure <rohit.m.ainapure@intel.com>
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds devicetree support to the wm8974 codec driver.
With a DT-based kernel, there is no board-specific setting
to select the driver so allow it to be manually chosen.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adding ACPI ID "MX98357A" for the MAXIM 98357A amp.
Signed-off-by: Rohit Ainapure <rohit.m.ainapure@intel.com>
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add driver for the Pulse Density Modulation Interface
Controller. It comes with digitallly controlled gain,
a High-Pass and a SINCC filter.
Signed-off-by: Songjun Wu <songjun.wu@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsrc-card is DPCM supported version of simple-card. Thus it has similar
DT format. OTOH, snd_soc_dai_link requests cpu/codec, but one of them
will be snd-soc-dummy in DPCM case, and DPCM requests frontend/backend
dai_link. This means it might have multi backend/codec.
And, SND_SOC_DAIFMT_xxx is based on "codec". Because of these
difference, current rsrc card can't detect correct dai_fmt.
This patch detect correct dai fmt from 1st "codec".
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
1efb53a220 ("ASoC: simple-card: Remove support for setting differing
DAI formats") removed set_fmt support from simple-card.
rsrc-card follows same style, because it is based on simple-card.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound driver will use tdm slot on TDM Multi Mode support.
This patch enables tdm slot on rsrc card driver on DT.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When power up, a "pop" is heard on line-in and mic-in.
An analysis of the PCM shows it lasts ~400ms
and looks like a filter response.
VAG power up should be delayed by 400ms as VAG power down is.
Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@veo-labs.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Older firmwares don't specify access flags for the controls,
unfortunately the usage of some of these firmware relies on being able
to read back values from the DSP. The current control code will only do
this for volatile controls. This patch will read the control from the
hardware if no flags are specified and the control is currently
enabled, which should cover these legacy use-cases.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
"data" is a u32 pointer so this copies the information to wrong place
entirely.
Fixes: 140adfba52 ('ASoC: Intel: Skylake: Add tlv byte kcontrols')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Tested-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sometimes PLL1 stops working if the codec loses power
during suspend (when pow-ldo2 or reset gpio is used).
MX-7Bh(RT5677_PLL1_CTRL2) is cleared and won't be restored
by regcache since it's volatile. MX-7Bh has one status bit
and M code for PLL1. rt5677_set_dai_pll doesn't reconfigure
PLL1 after resume because it thinks the PLL params are not
changed.
This patch clears the cached PLL params at resume so that
rt5677_set_dai_pll can reconfigure the PLL after resume.
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch rearranges the switch statement in arizona_calc_fratio so
that older codecs are the special cases, with the default case
applying to newer codecs (WM8998 and later). This is preferable
because it avoids having to patch new cases in every time a new
codec is added.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These need to be signed because they hold negative error codes.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sst_memcpy32() only copied bytes/4 32bits, which means it dropped
the remaining bytes%4 bytes wrongly.
Here add copying those missing bytes, first to a 32bits tmp, and
then write the tmp to 32bits iomem.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We use ret as the return value from the rsnd_mix_probe() but if there
are no child nodes and no errors then we will never initialize ret leading
to build warnings. Ensure ret is initialized before we iterate over the
child nodes to avoid this.
Signed-off-by: Mark Brown <broonie@kernel.org>
We use ret as the return value from the rsnd_dvc_probe() but if there
are no child nodes and no errors then we will never initialize ret leading
to build warnings. Ensure ret is initialized before we iterate over the
child nodes to avoid this.
Signed-off-by: Mark Brown <broonie@kernel.org>
We use ret as the return value from the rsnd_ctu_probe() but if there
are no child nodes and no errors then we will never initialize ret leading
to build warnings. Ensure ret is initialized before we iterate over the
child nodes to avoid this.
Signed-off-by: Mark Brown <broonie@kernel.org>
If driver received a message that it can't handle, it won't
clear the corresponding bit and unmask interrupt, this may
lock the IRQ and DSP can't send message anymore.
To fix the issue, we should Always update IMRX after IPC.
Here we always clear the DONE/BUSY bit and unmask the IRQ
source, even when IPC failures have occurred previously.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Modified-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for PA gpio pin for controlling an external amplifier as used
on some Allwinner boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rename the codec dapm widgets and routes with a _codec prefix. This is
a preparation patch for adding card dapm widgets and routes.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DPCM does not fully support symmetry attributes. soc_pcm_apply_symmetry()
is skipped in soc_pcm_open() for DPCM, without being applied elsewhere.
So HW parameters cannot be correctly limited, and user space can do
playback/capture at different rates while HW actually does not support it.
soc_pcm_params_symmetry() will return error and the second stream stops.
This patch adds soc_pcm_apply_symmetry() for FE, BE, and codec DAIs
in DPCM path that was skipped in soc_pcm_open().
Signed-off-by: PC Liao <pc.liao@mediatek.com>
Signed-off-by: Koro Chen <koro.chen@mediatek.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add code to unregister codec in probe function,
when the error occurs after the codec is registered.
Signed-off-by: Songjun Wu <songjun.wu@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Locking is currently missing from the DSP firmware controls, which can
lead to some race conditions if the controls are accessed as the DSP
powers up or down. This patch adds them to the new power lock.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should hold the DSP power lock whilst changing the firmware since we
need to check if it is running first.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Most events around the DSP just need to be locked to ensure that the DSP
can't change power state whilst they are happening. This includes the
debugfs entries and this will make sorting the rest of the locking
simpler.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add driver for Texas Instruments pcm3168a codec
Signed-off-by: Damien.Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Explicitly set the transmit data level on the transceiver to 16 samples
rather then the default 0. This matches both the level set in the vendor
kernel and the (seemingly very similar) i2s engine. This fixes audio
glitches when playing back at 192k rate.
At the same time, fix a trivial typo in the TDL mask definition
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Attempting to use this codec driver triggers a BUG() in regcache_sync()
since no cache type is set. The register map of this device is fairly
small and has few holes so a flat cache is suitable.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
These are all off by one; the playback and bypass switches are the top
two bits of the registers, which are at shifts 7 and 6 not 8 and 7.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The condition for checking for XDAT being cleared was not correct.
Fixes: 36bcecd0a7 ("ASoC: davinci-mcasp: Correct TX start sequence")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
This is using completely the wrong mask and value when updating the
register. Since the correct values are already defined in the header,
switch to using a table with explicit constants rather than shifting the
array index.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The previous commit removed the only use of these variables.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If we only clear the tx/rx state when both are disabled it is not
possible to start/stop one multiple times while the other is running.
Since the two are independently controlled, treat them as such and
remove the false dependency between capture and playback.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When building the da7218 driver on a 64-bit architecture, we get
a harmless warning:
sound/soc/codecs/da7218.c: In function 'da7218_of_get_id':
sound/soc/codecs/da7218.c:2261:10: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
This changes the code to use uintptr_t to ensure we have an integer
type of the same size as a pointer and won't get a warning on any
architecture.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 4d50934abd ("ASoC: da7218: Add da7218 codec driver")
Signed-off-by: Mark Brown <broonie@kernel.org>
We get a warning for the imx-pcm-fiq driver when CONFIG_LPAE
is enabled on ARM, because dma_addr_t is 64-bit then:
sound/soc/fsl/imx-pcm-fiq.c: In function 'snd_imx_pcm_mmap':
sound/soc/fsl/imx-pcm-fiq.c:223:107: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t {aka long long unsigned int}' [-Wformat=]
This changes the printk to use the correct format string for
printing a dma_addr_t.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Probing components can bring new DAI or DAI links based on the topology
info. This patch finds the unbound DAI links and bind them.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This function will return success immediately for a bound DAI link.
No need to look for the cpu/codec DAIs again.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A machine driver can register the two ops.
When a DAI link is added or removed by a component's topology, the
ASoC core can call the ops to notify the machine driver for extra
intialization or destruction.
E.g. topology can create FE DAI links from a cpu DAI component, and
the machine driver may define an add_dai_link ops to set machine-specific
.init ops for the DAI link.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Implement a dai link list for the soc card.
Add APIs to add/remove a DAI links dynamically, e.g. by topology.
And a dobj is embedded into the struct snd_soc_dai_link. Topology can
use the dobj to find the links created by it and remove them when the
topology component is unloaded.
The predefined DAI links are reserved to keep backward compatibility.
And they will also be added to the list.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should only add ignore suspend flag for some DAIs and not all.
This patches removes it from the DAIs where we do not support
this
It also marks the endpoints for which ignore_suspend should be
enabled
Signed-off-by: Praveen Diwakar <praveen.diwakar@intel.com>
Signed-off-by: Vunny Sodhi <vunnyx.sodhi@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some of the usecases can be marked as 'ignore_suspend' by
machine. For these on suspend we should keep audio controller
ON by saving the state and not suspending the device
For this we need to maintain a counter for these streams and be
active on suspend when such a stream is opened.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DAPM Machine map for machine was not specifying the paths
correctly.
The correct order should be:
"DMIC01 Rx" (SoC DMIC BE), connected to "DMIC AIF" (DMic Codec
AIF) and then "DMic" (DMic codec Input) connected to "SoC DMIC"
(Machine DMIC MIC Widget)
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since in Skylake we support another DAI for DMIC quad capture,
add a dailink for this as well. Also specify constrains for DMIC
FE devices and fixup for DMIC BEs
Signed-off-by: Dharageswari.R <dharageswari.r@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If a module is ON then we should read the module parameters from
DSP rather than driver cached values
Signed-off-by: Omair M Abdullah <omair.m.abdullah@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For messages which have larger payload than mailbox data, we need
to split the payload using set of messages containing mailbox
size as payload.
For sending such payload we already support LARGE_CONFIG_SET
IPCs and now to query such payload add LARGE_CONFIG_GET IPC
Signed-off-by: Mousami Jana <mousami.janax@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SKL actual mailbox size is 0x10000 and initial values were 0x800,
so update these accordingly
Signed-off-by: Omair M Abdullah <omair.m.abdullah@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Module initialization parameter data can be set by
- INIT_INSTANCE IPC by using the default value
- SET_PARAMS immediately after INIT_INSTANCE
- SET_PARAMS data from kcontrol values set
this patch add param type to identify the parameters
has to be sent to DSP.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mic select is a DSP module which is used to select one or many
inputs to form an output. This is useful to select data
selectively from PDM input and hence the name. This module is of
generic module type.
This patch adds support to add and configure Mic select module in
firmware topology.
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A module can require extra memory for processing, like audio
algorithms. The memory for these modules needs to be represented
in base module configuration and passed to DSP on init, so add
the memory pages as a field in widget data
Signed-off-by: Dharageswari.R <dharageswari.r@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A module is loaded when the path consisting the module is opened.
The module binary(ies) is loaded from file system and cached in
kernel memory for future use. This is downloaded to DSP using DMA
and invoking Load module IPCs
This patch adds support for load/unload module IPCs, DMAing
modules and manging the modules
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Previously we recorded "last interrupt position" and used it in
pointer callback. This is not correct implementation, and it causes
underruns when user space monitors buffer level to decide when to
send next data chunk in low latency application.
Remove position recording in IRQ handler and also hw_ptr in
struct mtk_afe_memif used to record that, and let pointer callback
reports current HW pointer instead.
Signed-off-by: Koro Chen <koro.chen@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
L/R channel data has been treated as inverted on R-Car sound 16bit mode,
Thus, 4689032b1("ASoC: rsnd: tidyup data align position") tidyuped data
align position. But it couldn't care about capture case. This patch
cares both playback/capture
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DWC IP can be powered off during system suspend in some platforms.
After system is resumed, dwc needs to be programmed again to continue
audio use case.
Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DWC in ACP 2.x IP has different offsets for I2S_COMP_PARAM_* registers.
Added a quirk to support the same.
Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When DW controller is in master mode, it can disable/enable clock
during the device runtime suspend/resume sequence.
Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
GPIOs are part of the AC'97 spec, enable their use on embedded platforms
using AC'97.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWX4h6AAoJECTWi3JdVIfQhIoH/2BB+Cdyzob3aAcIarYAPdsZ
bMXjDYyTyK1HanEUXGueQ7+CruQqXynRHhN3VRhmbjhJ+DgDP2GdgG53bm6q0J5z
TjoflP51OMX2boVokdyR3omOvuvoBDvhutVrHk5b/3Uye0p2yQ9kqdZgbvc8QE21
8QvJrm1PUg4OTj+xdUdl/uKweV7VUVMBob11NIM2C8UvURSv0lV+4UG/jy/fMHlz
KA/U0mPqCAz93XahxDHJzJsAO2O3q7K5Z1y5ZT0YXfrLiOFRGSIQSVjSZjPxAJkm
TAO6UMrxvLPEWuSqf5NcaMve5gveVbmHfocE/JvnRO8ylgGswF7wSflMPbcuYQ8=
=Fg8T
-----END PGP SIGNATURE-----
Merge tag 'asoc-ac97-gpio' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into devel
ASoC: Add a GPIO chip for AC'97
GPIOs are part of the AC'97 spec, enable their use on embedded platforms
using AC'97.
Both the sysclk and asyncclk members of arizona_priv are signed by we
refer to them through an unsigned pointer. This patch fixes this small
harmless error.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The core expects "const char * const" and "unsigned int" for enum
controls, various places in Arizona use "const char *" and "int".
This patch corrects the type of these arrays.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Always on widgets currently have some odd interactions with DAPM.
Enabling/disabling a widget (snd_soc_dapm_enable_pin) then connecting
it to a path works as expected, ie. when the widget is disabled the
path doesn't power up and it does when the widget is enabled. However
once in a path enabling the widget does not cause anything to power
up, dapm_widget_set_power will return the current power state of the
widget as 1, meaning we never check peer power states.
This patch updates dapm_always_on_check_power to return w->connected
such that it is effected by snd_soc_dapm_enable_pin and the like.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSICR::SWSP bit controls WS signal low/high, but in case of TDM
it is inverted. This patch solves this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds tlv bytes topology control creation and control load to
initialize kcontrol data. And this also adds the callbacks for
the these tlv byte kcontrols
Signed-off-by: Mythri P K <mythri.p.k@intel.com>
Signed-off-by: Divya Prakash <divya1.prakash@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds support to configure module parameter during module
initialization or after module init using set module param
required by the DSP firmware sequence.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some DSP modules has user configurable parameters, which are
required by some modules at module initialization.
To configure the module algorithm parameter during initialization
we add helpers here
Signed-off-by: Divya Prakash <divya1.prakash@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some DSP modules have user configurable parameters. These
parameters are required by modules in the following scenario
- during initialization
- after initialization using set parameter
This patch adds helper routine to set module parameters using
large config set IPC message and removes params to be passed as
init module routine.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On Skylake we can support upton 4DMICs on the PDM port, so update
the PCM capabilities accordingly
Also add a new DAI for DMIC pin which can be used for getting raw
DMIC data
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Dharageswari.R <dharageswari.r@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As a prerequisite for moving s3c64xx into multiplatform configurations,
we need to change the smartq audio driver to stop using hardcoded
gpio numbers from the header file, and instead pass the gpio data
through platform_data.
In order to do that, we also move the code to use module_platform_driver
and register the platform device using platform_device_register_simple
and register the gpios through the gpiod API.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
sound/soc/codecs/da7218.c:3214:9-10: WARNING: return of 0/1 in function 'da7218_volatile_register' with return type bool
Return statements in functions returning bool should use
true/false instead of 1/0.
Generated by: scripts/coccinelle/misc/boolreturn.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As hdac->num_nodes is unsigned we can not check if
snd_hdac_get_sub_nodes() has returned error or success. Lets have a
temporary int to check the error value.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
We have been returning success even if snd_soc_card_jack_new() fails.
Lets check the return value and return error if it fails.
Fixes: 12cc6d1dca ("ASoC: tegra_alc5632: Register jacks at the card level")
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 1fb34b4836 ('ASoC: sun4i: Implement MIC1 capture') added back some
code that disregards the clk_set_rate error code and always returns
-EINVAL. Fix that and return the code in order to have more clue about
what's going on.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The comment is misleading on how we should support external power amps, and
the variable is not used and generates a warning.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When switching between two clock sources using the FLL freerun to smooth
the transition we should wait 32uS after putting the FLL into freerun
before we proceed. In practice we appear to be getting enough delay from
the surrounding code, but better to make it explicit.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds missing check of snd_soc_of_get_dai_name().
It might not be able to use sound card, because it might returns
-EPROBE_DEFER.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
drv pointer should be "base + offset" instead of
"current + offset". This patch fixup this issue, otherwise
third and subsequent pointer will be broken
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas R-Car can out TDM by
1) 6ch x 1 DAI as TDM Extend Mode
2) 2ch x 4 x 1 DAI as TDM split Mode
3) 2ch x 3 DAI or
2ch x 4 DAI as TDM Multichannel Mode
This patch adds 1) TDM Extend Mode. Because of HW design,
this 6ch data will be outputed via 8ch data width.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current DVC is assuming that the sound is always stereo.
This patch makes it more flexible
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current SSI is assuming that the sound is always stereo. But, SSI needs
to calculate its frequency when master mode. Then This frequency depends
on each SSI's slots, and TDM mode (= TDM Extend Mode, TDM split Mode,
TDM Multichannel Mode).
This patch enables to use non-stereo sound.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It will have TDM settings on SSIWSR. Actually, we would like to set
it on rsnd_ssi_config_init(), but we can't. Because SSI might be used
as clock master (It doesn't need to call rsnd_ssi_config_init() when
clock master mode).
This patch adds new ssi->wsr and set it on rsnd_ssi_start().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
