Cc: Gleb Natapov <gleb@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The interrupt window is currently checked twice, once in vmx.c/svm.c and
once in dm_request_for_irq_injection. The only difference is the extra
check for kvm_arch_interrupt_allowed in dm_request_for_irq_injection,
and the different return value (EINTR/KVM_EXIT_INTR for vmx.c/svm.c vs.
0/KVM_EXIT_IRQ_WINDOW_OPEN for dm_request_for_irq_injection).
However, dm_request_for_irq_injection is basically dead code! Revive it
by removing the checks in vmx.c and svm.c's vmexit handlers, and
fixing the returned values for the dm_request_for_irq_injection case.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Avoid pointer chasing and memory barriers, and simplify the code
when split irqchip (LAPIC in kernel, IOAPIC/PIC in userspace)
is introduced.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We can reuse the algorithm that computes the EOI exit bitmap to figure
out which vectors are handled by the IOAPIC. The only difference
between the two is for edge-triggered interrupts other than IRQ8
that have no notifiers active; however, the IOAPIC does not have to
do anything special for these interrupts anyway.
This again limits the interactions between the IOAPIC and the LAPIC,
making it easier to move the former to userspace.
Inspired by a patch from Steve Rutherford.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This reverts commit fd717f1101.
It was reported to cause Machine Check Exceptions (bug 104091).
Reported-by: harn-solo@gmx.de
Cc: stable@vger.kernel.org # 4.2+
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reference SDM 28.1:
The current VPID is 0000H in the following situations:
- Outside VMX operation. (This includes operation in system-management
mode under the default treatment of SMIs and SMM with VMX operation;
see Section 34.14.)
- In VMX root operation.
- In VMX non-root operation when the “enable VPID” VM-execution control
is 0.
The VPID should never be 0000H in non-root operation when "enable VPID"
VM-execution control is 1. However, commit 34a1cd60 ("kvm: x86: vmx:
move some vmx setting from vmx_init() to hardware_setup()") remove the
codes which reserve 0000H for VMX root operation.
This patch fix it by again reserving 0000H for VMX root operation.
Cc: stable@vger.kernel.org # 3.19+
Fixes: 34a1cd60d1
Reported-by: Wincy Van <fanwenyi0529@gmail.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There are two kexec load syscalls, kexec_load another and kexec_file_load.
kexec_file_load has been splited as kernel/kexec_file.c. In this patch I
split kexec_load syscall code to kernel/kexec.c.
And add a new kconfig option KEXEC_CORE, so we can disable kexec_load and
use kexec_file_load only, or vice verse.
The original requirement is from Ted Ts'o, he want kexec kernel signature
being checked with CONFIG_KEXEC_VERIFY_SIG enabled. But kexec-tools use
kexec_load syscall can bypass the checking.
Vivek Goyal proposed to create a common kconfig option so user can compile
in only one syscall for loading kexec kernel. KEXEC/KEXEC_FILE selects
KEXEC_CORE so that old config files still work.
Because there's general code need CONFIG_KEXEC_CORE, so I updated all the
architecture Kconfig with a new option KEXEC_CORE, and let KEXEC selects
KEXEC_CORE in arch Kconfig. Also updated general kernel code with to
kexec_load syscall.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Dave Young <dyoung@redhat.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Petr Tesarik <ptesarik@suse.cz>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Josh Boyer <jwboyer@fedoraproject.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
alloc_pages_exact_node() was introduced in commit 6484eb3e2a ("page
allocator: do not check NUMA node ID when the caller knows the node is
valid") as an optimized variant of alloc_pages_node(), that doesn't
fallback to current node for nid == NUMA_NO_NODE. Unfortunately the
name of the function can easily suggest that the allocation is
restricted to the given node and fails otherwise. In truth, the node is
only preferred, unless __GFP_THISNODE is passed among the gfp flags.
The misleading name has lead to mistakes in the past, see for example
commits 5265047ac3 ("mm, thp: really limit transparent hugepage
allocation to local node") and b360edb43f ("mm, mempolicy:
migrate_to_node should only migrate to node").
Another issue with the name is that there's a family of
alloc_pages_exact*() functions where 'exact' means exact size (instead
of page order), which leads to more confusion.
To prevent further mistakes, this patch effectively renames
alloc_pages_exact_node() to __alloc_pages_node() to better convey that
it's an optimized variant of alloc_pages_node() not intended for general
usage. Both functions get described in comments.
It has been also considered to really provide a convenience function for
allocations restricted to a node, but the major opinion seems to be that
__GFP_THISNODE already provides that functionality and we shouldn't
duplicate the API needlessly. The number of users would be small
anyway.
Existing callers of alloc_pages_exact_node() are simply converted to
call __alloc_pages_node(), with the exception of sba_alloc_coherent()
which open-codes the check for NUMA_NO_NODE, so it is converted to use
alloc_pages_node() instead. This means it no longer performs some
VM_BUG_ON checks, and since the current check for nid in
alloc_pages_node() uses a 'nid < 0' comparison (which includes
NUMA_NO_NODE), it may hide wrong values which would be previously
exposed.
Both differences will be rectified by the next patch.
To sum up, this patch makes no functional changes, except temporarily
hiding potentially buggy callers. Restricting the checks in
alloc_pages_node() is left for the next patch which can in turn expose
more existing buggy callers.
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Robin Holt <robinmholt@gmail.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Christoph Lameter <cl@linux.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Mel Gorman <mgorman@suse.de>
Cc: David Rientjes <rientjes@google.com>
Cc: Greg Thelen <gthelen@google.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Cliff Whickman <cpw@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull x86 asm changes from Ingo Molnar:
"The biggest changes in this cycle were:
- Revamp, simplify (and in some cases fix) Time Stamp Counter (TSC)
primitives. (Andy Lutomirski)
- Add new, comprehensible entry and exit handlers written in C.
(Andy Lutomirski)
- vm86 mode cleanups and fixes. (Brian Gerst)
- 32-bit compat code cleanups. (Brian Gerst)
The amount of simplification in low level assembly code is already
palpable:
arch/x86/entry/entry_32.S | 130 +----
arch/x86/entry/entry_64.S | 197 ++-----
but more simplifications are planned.
There's also the usual laudry mix of low level changes - see the
changelog for details"
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (83 commits)
x86/asm: Drop repeated macro of X86_EFLAGS_AC definition
x86/asm/msr: Make wrmsrl() a function
x86/asm/delay: Introduce an MWAITX-based delay with a configurable timer
x86/asm: Add MONITORX/MWAITX instruction support
x86/traps: Weaken context tracking entry assertions
x86/asm/tsc: Add rdtscll() merge helper
selftests/x86: Add syscall_nt selftest
selftests/x86: Disable sigreturn_64
x86/vdso: Emit a GNU hash
x86/entry: Remove do_notify_resume(), syscall_trace_leave(), and their TIF masks
x86/entry/32: Migrate to C exit path
x86/entry/32: Remove 32-bit syscall audit optimizations
x86/vm86: Rename vm86->v86flags and v86mask
x86/vm86: Rename vm86->vm86_info to user_vm86
x86/vm86: Clean up vm86.h includes
x86/vm86: Move the vm86 IRQ definitions to vm86.h
x86/vm86: Use the normal pt_regs area for vm86
x86/vm86: Eliminate 'struct kernel_vm86_struct'
x86/vm86: Move fields from 'struct kernel_vm86_struct' to 'struct vm86'
x86/vm86: Move vm86 fields out of 'thread_struct'
...
VMX encodes access rights differently from LAR, and the latter is
most likely what x86 people think of when they think of "access
rights".
Rename them to avoid confusion.
Cc: kvm@vger.kernel.org
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The logic used to check ept misconfig is completely contained in common
reserved bits check for sptes, so it can be removed
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Allow a nested hypervisor to single step its guests.
Signed-off-by: Mihai Donțu <mihai.dontu@gmail.com>
[Fix overlong line. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
According to Intel SDM several checks must be applied for memory operands
of VMX instructions.
Long mode: #GP(0) or #SS(0) depending on the segment must be thrown
if the memory address is in a non-canonical form.
Protected mode, checks in chronological order:
- The segment type must be checked with access type (read or write) taken
into account.
For write access: #GP(0) must be generated if the destination operand
is located in a read-only data segment or any code segment.
For read access: #GP(0) must be generated if if the source operand is
located in an execute-only code segment.
- Usability of the segment must be checked. #GP(0) or #SS(0) depending on the
segment must be thrown if the segment is unusable.
- Limit check. #GP(0) or #SS(0) depending on the segment must be
thrown if the memory operand effective address is outside the segment
limit.
Signed-off-by: Eugene Korenevsky <ekorenevsky@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make them clearly architecture-dependent; the capability is valid for
all architectures, but the argument is not.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
OVMF depends on WB to boot fast, because it only clears caches after
it has set up MTRRs---which is too late.
Let's do writeback if CR0.CD is set to make it happy, similar to what
SVM is already doing.
Signed-off-by: Xiao Guangrong <guangrong.xiao@intel.com>
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently guest MTRR is avoided if kvm_is_reserved_pfn returns true.
However, the guest could prefer a different page type than UC for
such pages. A good example is that pass-throughed VGA frame buffer is
not always UC as host expected.
This patch enables full use of virtual guest MTRRs.
Suggested-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Tested-by: Joerg Roedel <jroedel@suse.de> (on AMD)
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now that there is no paravirt TSC, the "native" is
inappropriate. The function does RDTSC, so give it the obvious
name: rdtsc().
Suggested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Huang Rui <ray.huang@amd.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kvm ML <kvm@vger.kernel.org>
Link: http://lkml.kernel.org/r/fd43e16281991f096c1e4d21574d9e1402c62d39.1434501121.git.luto@kernel.org
[ Ported it to v4.2-rc1. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Now that the ->read_tsc() paravirt hook is gone, rdtscll() is
just a wrapper around native_read_tsc(). Unwrap it.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Huang Rui <ray.huang@amd.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kvm ML <kvm@vger.kernel.org>
Link: http://lkml.kernel.org/r/d2449ae62c1b1fb90195bcfb19ef4a35883a04dc.1434501121.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
"monitonic raw". Also some enhancements to make the ring buffer even
faster. But the biggest and most noticeable change is the renaming of
the ftrace* files, structures and variables that have to deal with
trace events.
Over the years I've had several developers tell me about their confusion
with what ftrace is compared to events. Technically, "ftrace" is the
infrastructure to do the function hooks, which include tracing and also
helps with live kernel patching. But the trace events are a separate
entity altogether, and the files that affect the trace events should
not be named "ftrace". These include:
include/trace/ftrace.h -> include/trace/trace_events.h
include/linux/ftrace_event.h -> include/linux/trace_events.h
Also, functions that are specific for trace events have also been renamed:
ftrace_print_*() -> trace_print_*()
(un)register_ftrace_event() -> (un)register_trace_event()
ftrace_event_name() -> trace_event_name()
ftrace_trigger_soft_disabled()-> trace_trigger_soft_disabled()
ftrace_define_fields_##call() -> trace_define_fields_##call()
ftrace_get_offsets_##call() -> trace_get_offsets_##call()
Structures have been renamed:
ftrace_event_file -> trace_event_file
ftrace_event_{call,class} -> trace_event_{call,class}
ftrace_event_buffer -> trace_event_buffer
ftrace_subsystem_dir -> trace_subsystem_dir
ftrace_event_raw_##call -> trace_event_raw_##call
ftrace_event_data_offset_##call-> trace_event_data_offset_##call
ftrace_event_type_funcs_##call -> trace_event_type_funcs_##call
And a few various variables and flags have also been updated.
This has been sitting in linux-next for some time, and I have not heard
a single complaint about this rename breaking anything. Mostly because
these functions, variables and structures are mostly internal to the
tracing system and are seldom (if ever) used by anything external to that.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJViYhVAAoJEEjnJuOKh9ldcJ0IAI+mytwoMAN/CWDE8pXrTrgs
aHlcr1zorSzZ0Lq6lKsWP+V0VGVhP8KWO16vl35HaM5ZB9U+cDzWiGobI8JTHi/3
eeTAPTjQdgrr/L+ZO1ApzS1jYPhN3Xi5L7xublcYMJjKfzU+bcYXg/x8gRt0QbG3
S9QN/kBt0JIIjT7McN64m5JVk2OiU36LxXxwHgCqJvVCPHUrriAdIX7Z5KRpEv13
zxgCN4d7Jiec/FsMW8dkO0vRlVAvudZWLL7oDmdsvNhnLy8nE79UOeHos2c1qifQ
LV4DeQ+2Hlu7w9wxixHuoOgNXDUEiQPJXzPc/CuCahiTL9N/urQSGQDoOVMltR4=
=hkdz
-----END PGP SIGNATURE-----
Merge tag 'trace-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"This patch series contains several clean ups and even a new trace
clock "monitonic raw". Also some enhancements to make the ring buffer
even faster. But the biggest and most noticeable change is the
renaming of the ftrace* files, structures and variables that have to
deal with trace events.
Over the years I've had several developers tell me about their
confusion with what ftrace is compared to events. Technically,
"ftrace" is the infrastructure to do the function hooks, which include
tracing and also helps with live kernel patching. But the trace
events are a separate entity altogether, and the files that affect the
trace events should not be named "ftrace". These include:
include/trace/ftrace.h -> include/trace/trace_events.h
include/linux/ftrace_event.h -> include/linux/trace_events.h
Also, functions that are specific for trace events have also been renamed:
ftrace_print_*() -> trace_print_*()
(un)register_ftrace_event() -> (un)register_trace_event()
ftrace_event_name() -> trace_event_name()
ftrace_trigger_soft_disabled() -> trace_trigger_soft_disabled()
ftrace_define_fields_##call() -> trace_define_fields_##call()
ftrace_get_offsets_##call() -> trace_get_offsets_##call()
Structures have been renamed:
ftrace_event_file -> trace_event_file
ftrace_event_{call,class} -> trace_event_{call,class}
ftrace_event_buffer -> trace_event_buffer
ftrace_subsystem_dir -> trace_subsystem_dir
ftrace_event_raw_##call -> trace_event_raw_##call
ftrace_event_data_offset_##call-> trace_event_data_offset_##call
ftrace_event_type_funcs_##call -> trace_event_type_funcs_##call
And a few various variables and flags have also been updated.
This has been sitting in linux-next for some time, and I have not
heard a single complaint about this rename breaking anything. Mostly
because these functions, variables and structures are mostly internal
to the tracing system and are seldom (if ever) used by anything
external to that"
* tag 'trace-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (33 commits)
ring_buffer: Allow to exit the ring buffer benchmark immediately
ring-buffer-benchmark: Fix the wrong type
ring-buffer-benchmark: Fix the wrong param in module_param
ring-buffer: Add enum names for the context levels
ring-buffer: Remove useless unused tracing_off_permanent()
ring-buffer: Give NMIs a chance to lock the reader_lock
ring-buffer: Add trace_recursive checks to ring_buffer_write()
ring-buffer: Allways do the trace_recursive checks
ring-buffer: Move recursive check to per_cpu descriptor
ring-buffer: Add unlikelys to make fast path the default
tracing: Rename ftrace_get_offsets_##call() to trace_event_get_offsets_##call()
tracing: Rename ftrace_define_fields_##call() to trace_event_define_fields_##call()
tracing: Rename ftrace_event_type_funcs_##call to trace_event_type_funcs_##call
tracing: Rename ftrace_data_offset_##call to trace_event_data_offset_##call
tracing: Rename ftrace_raw_##call event structures to trace_event_raw_##call
tracing: Rename ftrace_trigger_soft_disabled() to trace_trigger_soft_disabled()
tracing: Rename FTRACE_EVENT_FL_* flags to EVENT_FILE_FL_*
tracing: Rename struct ftrace_subsystem_dir to trace_subsystem_dir
tracing: Rename ftrace_event_name() to trace_event_name()
tracing: Rename FTRACE_MAX_EVENT to TRACE_EVENT_TYPE_MAX
...
for silicon that no one owns: these are really new features for
everyone.
* ARM: several features are in progress but missed the 4.2 deadline.
So here is just a smattering of bug fixes, plus enabling the VFIO
integration.
* s390: Some fixes/refactorings/optimizations, plus support for
2GB pages.
* x86: 1) host and guest support for marking kvmclock as a stable
scheduler clock. 2) support for write combining. 3) support for
system management mode, needed for secure boot in guests. 4) a bunch
of cleanups required for 2+3. 5) support for virtualized performance
counters on AMD; 6) legacy PCI device assignment is deprecated and
defaults to "n" in Kconfig; VFIO replaces it. On top of this there are
also bug fixes and eager FPU context loading for FPU-heavy guests.
* Common code: Support for multiple address spaces; for now it is
used only for x86 SMM but the s390 folks also have plans.
There are some x86 conflicts, one with the rc8 pull request and
the rest with Ingo's FPU rework.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJViYzhAAoJEL/70l94x66Dda0H/1IepMbfEy+o849d5G71fNTs
F8Y8qUP2GZuL7T53FyFUGSBw+AX7kimu9ia4gR/PmDK+QYsdosYeEjwlsolZfTBf
sHuzNtPoJhi5o1o/ur4NGameo0WjGK8f1xyzr+U8z74QDQyQv/QYCdK/4isp4BJL
ugHNHkuROX6Zng4i7jc9rfaSRg29I3GBxQUYpMkEnD3eMYMUBWGm6Rs8pHgGAMvL
vqzntgW00WNxehTqcAkmD/Wv+txxhkvIadZnjgaxH49e9JeXeBKTIR5vtb7Hns3s
SuapZUyw+c95DIipXq4EznxxaOrjbebOeFgLCJo8+XMXZum8RZf/ob24KroYad0=
=YsAR
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull first batch of KVM updates from Paolo Bonzini:
"The bulk of the changes here is for x86. And for once it's not for
silicon that no one owns: these are really new features for everyone.
Details:
- ARM:
several features are in progress but missed the 4.2 deadline.
So here is just a smattering of bug fixes, plus enabling the
VFIO integration.
- s390:
Some fixes/refactorings/optimizations, plus support for 2GB
pages.
- x86:
* host and guest support for marking kvmclock as a stable
scheduler clock.
* support for write combining.
* support for system management mode, needed for secure boot in
guests.
* a bunch of cleanups required for the above
* support for virtualized performance counters on AMD
* legacy PCI device assignment is deprecated and defaults to "n"
in Kconfig; VFIO replaces it
On top of this there are also bug fixes and eager FPU context
loading for FPU-heavy guests.
- Common code:
Support for multiple address spaces; for now it is used only for
x86 SMM but the s390 folks also have plans"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (124 commits)
KVM: s390: clear floating interrupt bitmap and parameters
KVM: x86/vPMU: Enable PMU handling for AMD PERFCTRn and EVNTSELn MSRs
KVM: x86/vPMU: Implement AMD vPMU code for KVM
KVM: x86/vPMU: Define kvm_pmu_ops to support vPMU function dispatch
KVM: x86/vPMU: introduce kvm_pmu_msr_idx_to_pmc
KVM: x86/vPMU: reorder PMU functions
KVM: x86/vPMU: whitespace and stylistic adjustments in PMU code
KVM: x86/vPMU: use the new macros to go between PMC, PMU and VCPU
KVM: x86/vPMU: introduce pmu.h header
KVM: x86/vPMU: rename a few PMU functions
KVM: MTRR: do not map huge page for non-consistent range
KVM: MTRR: simplify kvm_mtrr_get_guest_memory_type
KVM: MTRR: introduce mtrr_for_each_mem_type
KVM: MTRR: introduce fixed_mtrr_addr_* functions
KVM: MTRR: sort variable MTRRs
KVM: MTRR: introduce var_mtrr_range
KVM: MTRR: introduce fixed_mtrr_segment table
KVM: MTRR: improve kvm_mtrr_get_guest_memory_type
KVM: MTRR: do not split 64 bits MSR content
KVM: MTRR: clean up mtrr default type
...
This patch defines a new function pointer struct (kvm_pmu_ops) to
support vPMU for both Intel and AMD. The functions pointers defined in
this new struct will be linked with Intel and AMD functions later. In the
meanwhile the struct that maps from event_sel bits to PERF_TYPE_HARDWARE
events is renamed and moved from Intel specific code to kvm_host.h as a
common struct.
Reviewed-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Wei Huang <wei@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
MTRR code locates in x86.c and mmu.c so that move them to a separate file to
make the organization more clearer and it will be the place where we fully
implement vMTRR
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently, CR0.CD is not checked when we virtualize memory cache type for
noncoherent_dma guests, this patch fixes it by :
- setting UC for all memory if CR0.CD = 1
- zapping all the last sptes in MMU if CR0.CD is changed
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
... and we're done. :)
Because SMBASE is usually relocated above 1M on modern chipsets, and
SMM handlers might indeed rely on 4G segment limits, we only expose it
if KVM is able to run the guest in big real mode. This includes any
of VMX+emulate_invalid_guest_state, VMX+unrestricted_guest, or SVM.
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch has no semantic change, but it prepares for the introduction
of a second address space for system management mode.
A new function x86_set_memory_region (and the "slots_lock taken"
counterpart __x86_set_memory_region) is introduced in order to
operate on all address spaces when adding or deleting private
memory slots.
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We need to hide SMRAM from guests not running in SMM. Therefore,
all uses of kvm_read_guest* and kvm_write_guest* must be changed to
check whether the VCPU is in system management mode and use a
different set of memslots. Switch from kvm_* to the newly-introduced
kvm_vcpu_*, which call into kvm_arch_vcpu_memslots_id.
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
SMBASE is only readable from SMM for the VCPU, but it must be always
accessible if userspace is accessing it. Thus, all functions that
read MSRs are changed to accept a struct msr_data; the host_initiated
and index fields are pre-initialized, while the data field is filled
on return.
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If the host sets hardware breakpoints to debug the guest, and a task-switch
occurs in the guest, the architectural DR7 will not be updated. The effective
DR7 would be updated instead.
This fix puts the DR7 update during task-switch emulation, so it now uses the
standard DR setting mechanism instead of the one that was previously used. As a
bonus, the update of DR7 will now be effective for AMD as well.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rename this function in line with the new FPU nomenclature.
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Now that all FPU internals using drivers are converted to public APIs,
move xcr.h's definitions into fpu/internal.h and remove xcr.h.
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
There are a number of FPU internal function prototypes and an inline function
in fpu/api.h, mostly placed so historically as the code grew over the years.
Move them over into fpu/internal.h where they belong. (Add sched.h include
to stackprotector.h which incorrectly relied on getting it from fpu/api.h.)
fpu/api.h is now a pure file that only contains FPU APIs intended for driver
use.
Reviewed-by: Borislav Petkov <bp@alien8.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We already have fpu/types.h, move i387.h to fpu/api.h.
The file name has become a misnomer anyway: it offers generic FPU APIs,
but is not limited to i387 functionality.
Reviewed-by: Borislav Petkov <bp@alien8.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The term "ftrace" is really the infrastructure of the function hooks,
and not the trace events. Rename ftrace_event.h to trace_events.h to
represent the trace_event infrastructure and decouple the term ftrace
from it.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
vcpu->arch.apic is NULL when a userspace irqchip is active. But instead
of letting the test incorrectly depend on in-kernel irqchip mode,
open-code it to catch also userspace x2APICs.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
PAT should be 0007_0406_0007_0406h on RESET and not modified on INIT.
VMX used a wrong value (host's PAT) and while SVM used the right one,
it never got to arch.pat.
This is not an issue with QEMU as it will force the correct value.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
x86 architecture defines differences between the reset and INIT sequences.
INIT does not initialize the FPU (including MMX, XMM, YMM, etc.), TSC, PMU,
MSRs (in general), MTRRs machine-check, APIC ID, APIC arbitration ID and BSP.
References (from Intel SDM):
"If the MP protocol has completed and a BSP is chosen, subsequent INITs (either
to a specific processor or system wide) do not cause the MP protocol to be
repeated." [8.4.2: MP Initialization Protocol Requirements and Restrictions]
[Table 9-1. IA-32 Processor States Following Power-up, Reset, or INIT]
"If the processor is reset by asserting the INIT# pin, the x87 FPU state is not
changed." [9.2: X87 FPU INITIALIZATION]
"The state of the local APIC following an INIT reset is the same as it is after
a power-up or hardware reset, except that the APIC ID and arbitration ID
registers are not affected." [10.4.7.3: Local APIC State After an INIT Reset
("Wait-for-SIPI" State)]
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Message-Id: <1428924848-28212-1-git-send-email-namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The host's decision to enable machine check exceptions should remain
in force during non-root mode. KVM was writing 0 to cr4 on VCPU reset
and passed a slightly-modified 0 to the vmcs.guest_cr4 value.
Tested: Built.
On earlier version, tested by injecting machine check
while a guest is spinning.
Before the change, if guest CR4.MCE==0, then the machine check is
escalated to Catastrophic Error (CATERR) and the machine dies.
If guest CR4.MCE==1, then the machine check causes VMEXIT and is
handled normally by host Linux. After the change, injecting a machine
check causes normal Linux machine check handling.
Signed-off-by: Ben Serebrin <serebrin@google.com>
Reviewed-by: Venkatesh Srinivas <venkateshs@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
ARM/ARM64: fixes for live migration, irqfd and ioeventfd support (enabling
vhost, too), page aging
s390: interrupt handling rework, allowing to inject all local interrupts
via new ioctl and to get/set the full local irq state for migration
and introspection. New ioctls to access memory by virtual address,
and to get/set the guest storage keys. SIMD support.
MIPS: FPU and MIPS SIMD Architecture (MSA) support. Includes some patches
from Ralf Baechle's MIPS tree.
x86: bugfixes (notably for pvclock, the others are small) and cleanups.
Another small latency improvement for the TSC deadline timer.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJVJ9vmAAoJEL/70l94x66DoMEH/R3rh8IMf4jTiWRkcqohOMPX
k1+NaSY/lCKayaSgggJ2hcQenMbQoXEOdslvaA/H0oC+VfJGK+lmU6E63eMyyhjQ
Y+Px6L85NENIzDzaVu/TIWWuhil5PvIRr3VO8cvntExRoCjuekTUmNdOgCvN2ObW
wswN2qRdPIeEj2kkulbnye+9IV4G0Ne9bvsmUdOdfSSdi6ZcV43JcvrpOZT++mKj
RrKB+3gTMZYGJXMMLBwMkdl8mK1ozriD+q0mbomT04LUyGlPwYLl4pVRDBqyksD7
KsSSybaK2E4i5R80WEljgDMkNqrCgNfg6VZe4n9Y+CfAAOToNnkMJaFEi+yuqbs=
=yu2b
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"First batch of KVM changes for 4.1
The most interesting bit here is irqfd/ioeventfd support for ARM and
ARM64.
Summary:
ARM/ARM64:
fixes for live migration, irqfd and ioeventfd support (enabling
vhost, too), page aging
s390:
interrupt handling rework, allowing to inject all local interrupts
via new ioctl and to get/set the full local irq state for migration
and introspection. New ioctls to access memory by virtual address,
and to get/set the guest storage keys. SIMD support.
MIPS:
FPU and MIPS SIMD Architecture (MSA) support. Includes some
patches from Ralf Baechle's MIPS tree.
x86:
bugfixes (notably for pvclock, the others are small) and cleanups.
Another small latency improvement for the TSC deadline timer"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (146 commits)
KVM: use slowpath for cross page cached accesses
kvm: mmu: lazy collapse small sptes into large sptes
KVM: x86: Clear CR2 on VCPU reset
KVM: x86: DR0-DR3 are not clear on reset
KVM: x86: BSP in MSR_IA32_APICBASE is writable
KVM: x86: simplify kvm_apic_map
KVM: x86: avoid logical_map when it is invalid
KVM: x86: fix mixed APIC mode broadcast
KVM: x86: use MDA for interrupt matching
kvm/ppc/mpic: drop unused IRQ_testbit
KVM: nVMX: remove unnecessary double caching of MAXPHYADDR
KVM: nVMX: checks for address bits beyond MAXPHYADDR on VM-entry
KVM: x86: cache maxphyaddr CPUID leaf in struct kvm_vcpu
KVM: vmx: pass error code with internal error #2
x86: vdso: fix pvclock races with task migration
KVM: remove kvm_read_hva and kvm_read_hva_atomic
KVM: x86: optimize delivery of TSC deadline timer interrupt
KVM: x86: extract blocking logic from __vcpu_run
kvm: x86: fix x86 eflags fixed bit
KVM: s390: migrate vcpu interrupt state
...
After reset, the CPU can change the BSP, which will be used upon INIT. Reset
should return the BSP which QEMU asked for, and therefore handled accordingly.
To quote: "If the MP protocol has completed and a BSP is chosen, subsequent
INITs (either to a specific processor or system wide) do not cause the MP
protocol to be repeated."
[Intel SDM 8.4.2: MP Initialization Protocol Requirements and Restrictions]
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Message-Id: <1427933438-12782-3-git-send-email-namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
After speed-up of cpuid_maxphyaddr() it can be called frequently:
instead of heavyweight enumeration of CPUID entries it returns a cached
pre-computed value. It is also inlined now. So caching its result became
unnecessary and can be removed.
Signed-off-by: Eugene Korenevsky <ekorenevsky@gmail.com>
Message-Id: <20150329205644.GA1258@gnote>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
On each VM-entry CPU should check the following VMCS fields for zero bits
beyond physical address width:
- APIC-access address
- virtual-APIC address
- posted-interrupt descriptor address
This patch adds these checks required by Intel SDM.
Signed-off-by: Eugene Korenevsky <ekorenevsky@gmail.com>
Message-Id: <20150329205627.GA1244@gnote>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Exposing the on-stack error code with internal error is cheap and
potentially useful.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Message-Id: <1428001865-32280-1-git-send-email-rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use the normal return values for bool functions
Signed-off-by: Joe Perches <joe@perches.com>
Message-Id: <9f593eb2f43b456851cd73f7ed09654ca58fb570.1427759009.git.joe@perches.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some constants are redfined in emulate.c. Avoid it.
s/SELECTOR_RPL_MASK/SEGMENT_RPL_MASK
s/SELECTOR_TI_MASK/SEGMENT_TI_MASK
No functional change.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Message-Id: <1427635984-8113-3-git-send-email-namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If the guest CPU is supposed to support rdtscp and the host has rdtscp
enabled in the secondary execution controls, we can also expose this
feature to L1. Just extend nested_vmx_exit_handled to properly route
EXIT_REASON_RDTSCP.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This is needed in e.g. ARM vGIC emulation, where the MMIO handling
depends on the VCPU that does the access.
Signed-off-by: Nikolay Nikolaev <n.nikolaev@virtualopensystems.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
If EPT was enabled, unrestricted_guest was allowed in L1 regardless of
L0. L1 triple faulted when running L2 guest that required emulation.
Another side effect was 'WARN_ON_ONCE(vmx->nested.nested_run_pending)'
in L0's dmesg:
WARNING: CPU: 0 PID: 0 at arch/x86/kvm/vmx.c:9190 nested_vmx_vmexit+0x96e/0xb00 [kvm_intel] ()
Prevent this scenario by masking SECONDARY_EXEC_UNRESTRICTED_GUEST when
the host doesn't have it enabled.
Fixes: 78051e3b7e ("KVM: nVMX: Disable unrestricted mode if ept=0")
Cc: stable@vger.kernel.org
Tested-By: Kashyap Chamarthy <kchamart@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
While in L2, leave all #UD to L2 and do not try to emulate it. If L1 is
interested in doing this, it reports its interest via the exception
bitmap, and we never get into handle_exception of L0 anyway.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
In commit 3af18d9c5f ("KVM: nVMX: Prepare for using hardware MSR bitmap"),
we are setting MSR_BITMAP in prepare_vmcs02 if we should use hardware. This
is not enough since the field will be modified by following vmx_set_efer.
Fix this by setting vmx_msr_bitmap_nested in vmx_set_msr_bitmap if vcpu is
in guest mode.
Signed-off-by: Wincy Van <fanwenyi0529@gmail.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Currently kvm_emulate() skips the instruction but kvm_emulate_* sometimes
don't. The end reult is the caller ends up doing the skip themselves.
Let's make them consistant.
Signed-off-by: Joel Schopp <joel.schopp@amd.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
'apic' is not defined if !CONFIG_X86_64 && !CONFIG_X86_LOCAL_APIC.
Posted interrupt makes no sense without CONFIG_SMP, and
CONFIG_X86_LOCAL_APIC will be set with it.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pull x86 perf updates from Ingo Molnar:
"This series tightens up RDPMC permissions: currently even highly
sandboxed x86 execution environments (such as seccomp) have permission
to execute RDPMC, which may leak various perf events / PMU state such
as timing information and other CPU execution details.
This 'all is allowed' RDPMC mode is still preserved as the
(non-default) /sys/devices/cpu/rdpmc=2 setting. The new default is
that RDPMC access is only allowed if a perf event is mmap-ed (which is
needed to correctly interpret RDPMC counter values in any case).
As a side effect of these changes CR4 handling is cleaned up in the
x86 code and a shadow copy of the CR4 value is added.
The extra CR4 manipulation adds ~ <50ns to the context switch cost
between rdpmc-capable and rdpmc-non-capable mms"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86: Add /sys/devices/cpu/rdpmc=2 to allow rdpmc for all tasks
perf/x86: Only allow rdpmc if a perf_event is mapped
perf: Pass the event to arch_perf_update_userpage()
perf: Add pmu callbacks to track event mapping and unmapping
x86: Add a comment clarifying LDT context switching
x86: Store a per-cpu shadow copy of CR4
x86: Clean up cr4 manipulation
<asm/apic.h> isn't included directly and without CONFIG_SMP, an option
that automagically pulls it can't be enabled.
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Context switches and TLB flushes can change individual bits of CR4.
CR4 reads take several cycles, so store a shadow copy of CR4 in a
per-cpu variable.
To avoid wasting a cache line, I added the CR4 shadow to
cpu_tlbstate, which is already touched in switch_mm. The heaviest
users of the cr4 shadow will be switch_mm and __switch_to_xtra, and
__switch_to_xtra is called shortly after switch_mm during context
switch, so the cacheline is likely to be hot.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Vince Weaver <vince@deater.net>
Cc: "hillf.zj" <hillf.zj@alibaba-inc.com>
Cc: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/3a54dd3353fffbf84804398e00dfdc5b7c1afd7d.1414190806.git.luto@amacapital.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
CR4 manipulation was split, seemingly at random, between direct
(write_cr4) and using a helper (set/clear_in_cr4). Unfortunately,
the set_in_cr4 and clear_in_cr4 helpers also poke at the boot code,
which only a small subset of users actually wanted.
This patch replaces all cr4 access in functions that don't leave cr4
exactly the way they found it with new helpers cr4_set_bits,
cr4_clear_bits, and cr4_set_bits_and_update_boot.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Vince Weaver <vince@deater.net>
Cc: "hillf.zj" <hillf.zj@alibaba-inc.com>
Cc: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/495a10bdc9e67016b8fd3945700d46cfd5c12c2f.1414190806.git.luto@amacapital.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
If vcpu has a interrupt in vmx non-root mode, injecting that interrupt
requires a vmexit. With posted interrupt processing, the vmexit
is not needed, and interrupts are fully taken care of by hardware.
In nested vmx, this feature avoids much more vmexits than non-nested vmx.
When L1 asks L0 to deliver L1's posted interrupt vector, and the target
VCPU is in non-root mode, we use a physical ipi to deliver POSTED_INTR_NV
to the target vCPU. Using POSTED_INTR_NV avoids unexpected interrupts
if a concurrent vmexit happens and L1's vector is different with L0's.
The IPI triggers posted interrupt processing in the target physical CPU.
In case the target vCPU was not in guest mode, complete the posted
interrupt delivery on the next entry to L2.
Signed-off-by: Wincy Van <fanwenyi0529@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
With virtual interrupt delivery, the hardware lets KVM use a more
efficient mechanism for interrupt injection. This is an important feature
for nested VMX, because it reduces vmexits substantially and they are
much more expensive with nested virtualization. This is especially
important for throughput-bound scenarios.
Signed-off-by: Wincy Van <fanwenyi0529@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We can reduce apic register virtualization cost with this feature,
it is also a requirement for virtual interrupt delivery and posted
interrupt processing.
Signed-off-by: Wincy Van <fanwenyi0529@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
To enable nested apicv support, we need per-cpu vmx
control MSRs:
1. If in-kernel irqchip is enabled, we can enable nested
posted interrupt, we should set posted intr bit in
the nested_vmx_pinbased_ctls_high.
2. If in-kernel irqchip is disabled, we can not enable
nested posted interrupt, the posted intr bit
in the nested_vmx_pinbased_ctls_high will be cleared.
Since there would be different settings about in-kernel
irqchip between VMs, different nested control MSRs
are needed.
Signed-off-by: Wincy Van <fanwenyi0529@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When L2 is using x2apic, we can use virtualize x2apic mode to
gain higher performance, especially in apicv case.
This patch also introduces nested_vmx_check_apicv_controls
for the nested apicv patches.
Signed-off-by: Wincy Van <fanwenyi0529@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently, if L1 enables MSR_BITMAP, we will emulate this feature, all
of L2's msr access is intercepted by L0. Features like "virtualize
x2apic mode" require that the MSR bitmap is enabled, or the hardware
will exit and for example not virtualize the x2apic MSRs. In order to
let L1 use these features, we need to build a merged bitmap that only
not cause a VMEXIT if 1) L1 requires that 2) the bit is not required by
the processor for APIC virtualization.
For now the guests are still run with MSR bitmap disabled, but this
patch already introduces nested_vmx_merge_msr_bitmap for future use.
Signed-off-by: Wincy Van <fanwenyi0529@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Revert 7c6a98dfa1, given
that testing PIR is not necessary anymore.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A function pointer was not NULLed, causing kvm_vcpu_reload_apic_access_page to
go down the wrong path and OOPS when doing put_page(NULL).
This did not happen on old processors, only when setting the module option
explicitly.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch adds PML support in VMX. A new module parameter 'enable_pml' is added
to allow user to enable/disable it manually.
Signed-off-by: Kai Huang <kai.huang@linux.intel.com>
Reviewed-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Removes some functions that are not used anywhere:
cpu_has_vmx_eptp_writeback() cpu_has_vmx_eptp_uncacheable()
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The initialization function in mmu.c can always use walk_mmu, which
is known to be vcpu->arch.mmu. Only init_kvm_nested_mmu is used to
initialize vcpu->arch.nested_mmu.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
kvm_x86_ops->test_posted_interrupt() returns true/false depending
whether 'vector' is set.
Next patch makes use of this interface.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In most cases calling hwapic_isr_update(), we always check if
kvm_apic_vid_enabled() == 1, but actually,
kvm_apic_vid_enabled()
-> kvm_x86_ops->vm_has_apicv()
-> vmx_vm_has_apicv() or '0' in svm case
-> return enable_apicv && irqchip_in_kernel(kvm)
So its a little cost to recall vmx_vm_has_apicv() inside
hwapic_isr_update(), here just NULL out hwapic_isr_update() in
case of !enable_apicv inside hardware_setup() then make all
related stuffs follow this. Note we don't check this under that
condition of irqchip_in_kernel() since we should make sure
definitely any caller don't work without in-kernel irqchip.
Signed-off-by: Tiejun Chen <tiejun.chen@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When generating #PF VM-exit, check equality:
(PFEC & PFEC_MASK) == PFEC_MATCH
If there is equality, the 14 bit of exception bitmap is used to take decision
about generating #PF VM-exit. If there is inequality, inverted 14 bit is used.
Signed-off-by: Eugene Korenevsky <ekorenevsky@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch improve checks required by Intel Software Developer Manual.
- SMM MSRs are not allowed.
- microcode MSRs are not allowed.
- check x2apic MSRs only when LAPIC is in x2apic mode.
- MSR switch areas must be aligned to 16 bytes.
- address of first and last byte in MSR switch areas should not set any bits
beyond the processor's physical-address width.
Also it adds warning messages on failures during MSR switch. These messages
are useful for people who debug their VMMs in nVMX.
Signed-off-by: Eugene Korenevsky <ekorenevsky@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Several hypervisors need MSR auto load/restore feature.
We read MSRs from VM-entry MSR load area which specified by L1,
and load them via kvm_set_msr in the nested entry.
When nested exit occurs, we get MSRs via kvm_get_msr, writing
them to L1`s MSR store area. After this, we read MSRs from VM-exit
MSR load area, and load them via kvm_set_msr.
Signed-off-by: Wincy Van <fanwenyi0529@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The commit 34a1cd60d1, "x86: vmx: move some vmx setting from
vmx_init() to hardware_setup()", tried to refactor some codes
specific to vmx hardware setting into hardware_setup(), but some
msr writing should depend on our previous setting condition like
enable_apicv, enable_ept and so on.
Reported-by: Jamie Heilman <jamie@audible.transient.net>
Tested-by: Jamie Heilman <jamie@audible.transient.net>
Signed-off-by: Tiejun Chen <tiejun.chen@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If L0 has disabled EPT, don't advertise unrestricted
mode at all since it depends on EPT to run real mode code.
Fixes: 92fbc7b195
Cc: stable@vger.kernel.org
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add nested virtualization support for xsaves.
Signed-off-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add logic to get/set the XSS model-specific register.
Signed-off-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Initialize the XSS exit bitmap. It is zero so there should be no XSAVES
or XRSTORS exits.
Signed-off-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Expose the XSAVES feature to the guest if the kvm_x86_ops say it is
available.
Signed-off-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Instead, just use PFERR_{FETCH, PRESENT, WRITE}_MASK
inside handle_ept_violation() for slightly better code.
Signed-off-by: Tiejun Chen <tiejun.chen@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There's nothing to switch if the host and guest values are the same.
I am unable to find evidence that this makes any difference
whatsoever.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
[I could see a difference on Nehalem. From 5 runs:
userspace exit, guest!=host 12200 11772 12130 12164 12327
userspace exit, guest=host 11983 11780 11920 11919 12040
lightweight exit, guest!=host 3214 3220 3238 3218 3337
lightweight exit, guest=host 3178 3193 3193 3187 3220
This passes the t-test with 99% confidence for userspace exit,
98.5% confidence for lightweight exit. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
At least on Sandy Bridge, letting the CPU switch IA32_EFER is much
faster than switching it manually.
I benchmarked this using the vmexit kvm-unit-test (single run, but
GOAL multiplied by 5 to do more iterations):
Test Before After Change
cpuid 2000 1932 -3.40%
vmcall 1914 1817 -5.07%
mov_from_cr8 13 13 0.00%
mov_to_cr8 19 19 0.00%
inl_from_pmtimer 19164 10619 -44.59%
inl_from_qemu 15662 10302 -34.22%
inl_from_kernel 3916 3802 -2.91%
outl_to_kernel 2230 2194 -1.61%
mov_dr 172 176 2.33%
ipi (skipped) (skipped)
ipi+halt (skipped) (skipped)
ple-round-robin 13 13 0.00%
wr_tsc_adjust_msr 1920 1845 -3.91%
rd_tsc_adjust_msr 1892 1814 -4.12%
mmio-no-eventfd:pci-mem 16394 11165 -31.90%
mmio-wildcard-eventfd:pci-mem 4607 4645 0.82%
mmio-datamatch-eventfd:pci-mem 4601 4610 0.20%
portio-no-eventfd:pci-io 11507 7942 -30.98%
portio-wildcard-eventfd:pci-io 2239 2225 -0.63%
portio-datamatch-eventfd:pci-io 2250 2234 -0.71%
I haven't explicitly computed the significance of these numbers,
but this isn't subtle.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
[The results were reproducible on all of Nehalem, Sandy Bridge and
Ivy Bridge. The slowness of manual switching is because writing
to EFER with WRMSR triggers a TLB flush, even if the only bit you're
touching is SCE (so the page table format is not affected). Doing
the write as part of vmentry/vmexit, instead, does not flush the TLB,
probably because all processors that have EPT also have VPID. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
x86 debug registers hold a linear address. Therefore, breakpoints detection
should consider CS.base, and check whether instruction linear address equals
(CS.base + RIP). This patch introduces a function to evaluate RIP linear
address and uses it for breakpoints detection.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
DR6[0:3] (previous breakpoint indications) are cleared when #DB is injected
during handle_exception, just as real hardware does. Similarily, handle_dr
should clear DR6[0:3].
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A bug was reported as follows: when running Windows 7 32-bit guests on qemu-kvm,
sometimes the guests run into blue screen during reboot. The problem was that a
guest's RVI was not cleared when it rebooted. This patch has fixed the problem.
Signed-off-by: Wei Wang <wei.w.wang@intel.com>
Signed-off-by: Yang Zhang <yang.z.zhang@intel.com>
Tested-by: Rongrong Liu <rongrongx.liu@intel.com>, Da Chun <ngugc@qq.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Return a negative error code instead, and WARN() when we should be covering
the entire 2-bit space of vmcs_field_type's return value. For increased
robustness, add a BUILD_BUG_ON checking the range of vmcs_field_to_offset.
Suggested-by: Tiejun Chen <tiejun.chen@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Instead of vmx_init(), actually it would make reasonable sense to do
anything specific to vmx hardware setting in vmx_x86_ops->hardware_setup().
Signed-off-by: Tiejun Chen <tiejun.chen@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Just move this pair of functions down to make sure later we can
add something dependent on others.
Signed-off-by: Tiejun Chen <tiejun.chen@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If DR4/5 is accessed when it is unavailable (since CR4.DE is set), then #UD
should be generated even if CPL>0. This is according to Intel SDM Table 6-2:
"Priority Among Simultaneous Exceptions and Interrupts".
Note, that this may happen on the first DR access, even if the host does not
sets debug breakpoints. Obviously, it occurs when the host debugs the guest.
This patch moves the DR4/5 checks from __kvm_set_dr/_kvm_get_dr to handle_dr.
The emulator already checks DR4/5 availability in check_dr_read. Nested
virutalization related calls to kvm_set_dr/kvm_get_dr would not like to inject
exceptions to the guest.
As for SVM, the patch follows the previous logic as much as possible. Anyhow,
it appears the DR interception code might be buggy - even if the DR access
may cause an exception, the instruction is skipped.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
DR7.LE should be cleared during task-switch. This feature is poorly documented.
For reference, see:
http://pdos.csail.mit.edu/6.828/2005/readings/i386/s12_02.htm
SDM [17.2.4]:
This feature is not supported in the P6 family processors, later IA-32
processors, and Intel 64 processors.
AMD [2:13.1.1.4]:
This bit is ignored by implementations of the AMD64 architecture.
Intel's formulation could mean that it isn't even zeroed, but current
hardware indeed does not behave like that.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Intel SDM 17.2.4 (Debug Control Register (DR7)) says: "The processor clears the
GD flag upon entering to the debug exception handler." This sentence may be
misunderstood as if it happens only on #DB due to debug-register protection,
but it happens regardless to the cause of the #DB.
Fix the behavior to match both real hardware and Bochs.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
CR4.TSD is guest-owned; don't trap writes to it in VMX guests. This
avoids a VM exit on context switches into or out of a PR_TSC_SIGSEGV
task.
I think that this fixes an unintentional side-effect of:
4c38609ac5 KVM: VMX: Make guest cr4 mask more conservative
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In order to access the shadow VMCS, we need to load it. At this point,
vmx->loaded_vmcs->vmcs and the actually loaded one start to differ. If
we now get preempted by Linux, vmx_vcpu_put and, on return, the
vmx_vcpu_load will work against the wrong vmcs. That can cause
copy_shadow_to_vmcs12 to corrupt the vmcs12 state.
Fix the issue by disabling preemption during the copy operation.
copy_vmcs12_to_shadow is safe from this issue as it is executed by
vmx_vcpu_run when preemption is already disabled before vmentry.
This bug is exposed by running Jailhouse within KVM on CPUs with
shadow VMCS support. Jailhouse never expects an interrupt pending
vmexit, but the bug can cause it if, after copy_shadow_to_vmcs12
is preempted, the active VMCS happens to have the virtual interrupt
pending flag set in the CPU-based execution controls.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM_EXIT_UNKNOWN is a kvm bug, we don't really know whether it was
triggered by a priveledged application. Let's not kill the guest: WARN
and inject #UD instead.
Cc: stable@vger.kernel.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
