The device which identifies itself as a "USB Keykoard" (no typo)
with VID:PID 1a2c:0027 does not seem to be handling the reports
initialization very well.
This results in a "usb_submit_urb(ctrl) failed: -1" message from the
kernel when connected, and a delay before its initialization. It can
also cause the hang the system.
This patch adds the quirk for this device, which causes the delay
to disappear. It is named as "USB Keykoard2" because the "USB Keykoard"
already exists.
Signed-off-by: Daniel Bristot de Oliveira <bristot@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The midi controller times-out while initializing reports, this
causes boot to take an extra 10 seconds. The device descriptor
advertises that it has an internal HID device but seems to not
actually do anything useful.
Signed-off-by: Stafford Horne <shorne@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID updates from Jiri Kosina:
- appoint Benjamin Tissoires as co-maintainer / designated reviewer
- sysfs report_descriptor visibility fix for unclaimed devices, from
Andy Lutomirski
- suspend/resume fixes for Sony driver from Frank Praznik
- IRQ deadlock fix from Ioan-Adrian Ratiu
- hid-i2c fixes affecting (at least) Yoga 900 from Mika Westerberg and
Srinivas Pandruvada
- a lot of new device support (especially, but not limited to, Wacom)
and assorted small misc fixes
- almost complete G920 support; the only bit that is missing is
switching the device to HID mode automatically; Simon Wood and Michal
Maly are working on it.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (46 commits)
Revert "INPUT: xpad: switch Logitech G920 Wheel into HID mode"
HID: sensor-hub: Add quirk for Lenovo Yoga 900 with ITE Chips
HID: Add new PID for Microchip Pick16F1454
HID: wacom: Use correct report to query pen ID from INTUOSHT2 devices
HID: i2c-hid: Prevent sending reports from racing with device reset
HID: use kobj_to_dev()
HID: wiimote: use dev_to_wii()
HID: add a new helper to_hid_driver()
HID: use to_hid_device()
HID: move to_hid_device() to hid.h
HID: usbhid: use to_usb_device
HID: corsair: Convert to use module_hid_driver
HID: input: ignore the battery in OKLICK Laser BTmouse
HID: wacom: Fix pad button range for CINTIQ_COMPANION_2
HID: wacom: Fix touchring value reporting
HID: wacom: Report 'strip2' values in ABS_RY
HID: wacom: Limit touchstrip data to 13 bits
HID: wacom: bitwise vs logical ORs
HID: wacom: Apply lowres quirk to BAMBOO_TOUCH devices
HID: enable hid device to suspend/resume asynchronously
...
Here are a number of small USB fixes for 4.4-rc5. All of them have been
in linux-next. The majority are gadget and phy issues, with a few new
quirks and device ids added as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlZs8fkACgkQMUfUDdst+ym/HwCgxdhop3PMk9QxCVaEdxcqv10p
PDkAn0uOW1sdRsHVRhutjcc29+AUJggk
=ybrB
-----END PGP SIGNATURE-----
Merge tag 'usb-4.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB driver fixes from Greg KH:
"Here are a number of small USB fixes for 4.4-rc5. All of them have
been in linux-next. The majority are gadget and phy issues, with a
few new quirks and device ids added as well"
* tag 'usb-4.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (32 commits)
USB: add quirk for devices with broken LPM
xhci: fix usb2 resume timing and races.
usb: musb: fail with error when no DMA controller set
usb: gadget: uvc: fix permissions of configfs attributes
usb: musb: core: Fix pm runtime for deferred probe
usb: phy: msm: fix a possible NULL dereference
USB: host: ohci-at91: fix a crash in ohci_hcd_at91_overcurrent_irq
usb: Quiet down false peer failure messages
usb: xhci: fix config fail of FS hub behind a HS hub with MTT
xhci: Fix memory leak in xhci_pme_acpi_rtd3_enable()
usb: Use the USB_SS_MULT() macro to decode burst multiplier for log message
USB: whci-hcd: add check for dma mapping error
usb: core : hub: Fix BOS 'NULL pointer' kernel panic
USB: quirks: Apply ALWAYS_POLL to all ELAN devices
usb-storage: Fix scsi-sd failure "Invalid field in cdb" for USB adapter JMicron
USB: quirks: Fix another ELAN touchscreen
usb: dwc3: gadget: don't prestart interrupt endpoints
USB: serial: Another Infineon flash loader USB ID
USB: cdc_acm: Ignore Infineon Flash Loader utility
USB: cp210x: Remove CP2110 ID from compatibility list
...
All ELAN hid devices seem to require the ALWAYS_POLL quirk. Let's use
this quirk for all devices from this vendor, rather than maintaining a
list of all its known product IDs.
Tested-by: Adrien Vergé <adrienverge@gmail.com>
Signed-off-by: Adrien Vergé <adrienverge@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The critical section protected by usbhid->lock in hid_ctrl() is too
big and because of this it causes a recursive deadlock. "Too big" means
the case statement and the call to hid_input_report() do not need to be
protected by the spinlock (no URB operations are done inside them).
The deadlock happens because in certain rare cases drivers try to grab
the lock while handling the ctrl irq which grabs the lock before them
as described above. For example newer wacom tablets like 056a:033c try
to reschedule proximity reads from wacom_intuos_schedule_prox_event()
calling hid_hw_request() -> usbhid_request() -> usbhid_submit_report()
which tries to grab the usbhid lock already held by hid_ctrl().
There are two ways to get out of this deadlock:
1. Make the drivers work "around" the ctrl critical region, in the
wacom case for ex. by delaying the scheduling of the proximity read
request itself to a workqueue.
2. Shrink the critical region so the usbhid lock protects only the
instructions which modify usbhid state, calling hid_input_report()
with the spinlock unlocked, allowing the device driver to grab the
lock first, finish and then grab the lock afterwards in hid_ctrl().
This patch implements the 2nd solution.
Signed-off-by: Ioan-Adrian Ratiu <adi@adirat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If an event is discarded the device stays idle. Just reverse the order of
check and marking busy.
Found by code inspection.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Without quirk keyboard repeats '6' until volume control is used since it
indicates the key is pressed without ever releasing.
Signed-off-by: Jimmy Berry <jimmy@boombatower.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The WiiU adapter from Mayflash (see
http://www.mayflash.com/Products/NINTENDOWiiU/W009.html) is not
working correctly.
The "XInput" mode works fine, the controller is recognized as a xbox
controller. But it is only possible to connect one controller with this method.
In "DInput" mode the device is recognized as some kind of mouse input but no
joystick is created. This commit will change this behavior with
HID_QUIRK_MULTI_INPUT to split the device into 4 input devices so that it will
also create joysticks in /dev/input/js*.
Signed-off-by: Oliver Schmitt <voltumna@gmx.net>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Adds support for Microsoft Type Cover 3 with 0x07e2 product ID.
Signed-off-by: Donavan Lance <shvr@fedoraproject.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Looks like 0x8882 needs the same quirk than 0x8883.
Given that both devices claim they are "TPV OpticalTouchScreen" rename
the 0x8883 to add its PID in the #define.
Reported-by: Blaine Lee <blaine.j.lee@medtronic.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It was reported that after 10-20 reboots, a usb keyboard plugged
into a docking station would not work unless it was replugged in.
Using usbmon, it turns out the interrupt URBs were streaming with
callback errors of -71 for some reason. The hid-core.c::hid_io_error was
supposed to retry and then reset, but the reset wasn't really happening.
The check for HID_NO_BANDWIDTH was inverted. Fix was simple.
Tested by reporter and locally by me by unplugging a keyboard halfway until I
could recreate a stream of errors but no disconnect.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Adding support for the Microsoft Surface 3 (non-pro) Type Cover.
The existing definitions and quirks are actually for the Surface
Pro 3 type covers. I've renamed the old constants to reflect that
they belong to the Surface Pro 3, and added a new constant and
matching code for the Surface 3.
Signed-off-by: Stephen Just <stephenjust@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
During open() it is unnecessary to wait for the device to flush
stale inputs if the device is polled while closed due to a quirk
or opening fails.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The newer firmware on MS Surface 2 tablets causes the type and touch cover keyboards to timeout when waiting for reports.
The quirk HID_QUIRK_NO_INIT_REPORTS allows them to function normally.
Signed-off-by: Reyad Attiyat <reyad.attiyat@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Adding support for the Microsoft Surface Pro Power Cover.
Signed-off-by: Raimund Roth <raimundmroth@gmail.gom>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
I received a report from an user of following mouse which needs this quirk:
usb 1-1.6: USB disconnect, device number 58
usb 1-1.6: new low speed USB device number 59 using ehci_hcd
usb 1-1.6: New USB device found, idVendor=04f2, idProduct=1053
usb 1-1.6: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-1.6: Product: USB Optical Mouse
usb 1-1.6: Manufacturer: PixArt
usb 1-1.6: configuration #1 chosen from 1 choice
input: PixArt USB Optical Mouse as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.6/1-1.6:1.0/input/input5887
generic-usb 0003:04F2:1053.16FE: input,hidraw2: USB HID v1.11 Mouse [PixArt USB Optical Mouse] on usb-0000:00:1a.0-1.6/input0
The quirk was tested by the reporter and it fixed the frequent disconnections etc.
[jkosina@suse.cz: reorder the position in hid-ids.h]
Signed-off-by: Herton R. Krzesinski <herton@redhat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Like other KVM switches, the Aten DVI KVM switch needs a quirk to avoid spewing
errors:
[791759.606542] usb 1-5.4: input irq status -75 received
[791759.614537] usb 1-5.4: input irq status -75 received
[791759.622542] usb 1-5.4: input irq status -75 received
Add it.
Signed-off-by: Laura Abbott <labbott@fedoraproject.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The raphnet.net 4nes4snes and 2nes2snes multi-joystick adapters use a single
HID report descriptor with one report ID per controller. This has the effect
that the inputs of otherwise independent game controllers get packed in one
large joystick device.
With this patch each controller gets its own /dev/input/jsX device, which is
more natural and less confusing than having all inputs going to the same place.
Signed-off-by: Raphael Assenat <raph@raphnet.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The device exists with two device IDs instead of one as previously
believed.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
During a stress test these mice kept dropping and reappearing
in runlevel 1 as opposed to 5.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Force-beedback core guarantees that the 'effect' pointer that's being passed
to ->upload() callback is non-NULL.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This mouse is also known under other IDs. It needs the quirk or will disconnect
in runlevel 1 or 3.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
CC: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The PID driver (usbhid/hid-pidff.c) does not set the effect ID when
uploading an effect. The result is that the initial upload works but
subsequent uploads to modify effect parameters are all directed at the
last-created effect.
The targeted effect ID must be passed back to the device when effect
parameters are changed. This is done at the start of
"pidff_set_condition_report", "pidff_set_periodic_report" etc. based on
the value of "pidff->block_load[PID_EFFECT_
BLOCK_INDEX].value[0]".
This value is only ever set during pidff_request_effect_upload.
The result is stored in "pidff->pid_id[effect->id]" at the end of
pid_upload_effect, for later use. However, if an effect is modified and
re-sent then this identifier is not being copied back from
pidff->pid_id[effect->id] before sending the command to the device. The
fix is to do this at the start of pidff_upload_effect.
Signed-off-by: Jim Keir <jimkeir@oracledbadirect.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Based on a patch from: Nikolai Kondrashov <Nikolai.Kondrashov@redhat.com>
Most of the tablets handled by hid-uclogic already use MULTI_INPUT.
For the ones which are not quirked in usbhid/hidquirks, they have a
custom report descriptor which contains only one report per HID
interface. For those tablets HID_QUIRK_MULTI_INPUT is transparent.
According to https://github.com/DIGImend/tablets, the only problematic
tablet currently handled by hid-uclogic is the TWHA60 v3. This tablet
presents different report descriptors from the ones currently quirked.
This is not a problem per se, given that this tablet is not supported
currently in this version (it needs the same command as a Huion to
start forwarding events).
Reviewed-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Genius PenSketch M912 digitizer tablet sends incorrect report descriptor by
default. This patch replaces it with a corrected one.
Signed-off-by: Milan Plzik <milan.plzik@gmail.com>
Reviewed-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The FF2 driver (usbhid/hid-pidff.c) sends commands to the stick during ff_init.
However, this is called inside a block where driver_input_lock is locked, so
the results of these initial commands are discarded. This behavior is the
"killer", without this nothing else works.
ff_init issues commands using "hid_hw_request". This eventually goes to
hid_input_report, which returns -EBUSY because driver_input_lock is locked. The
change is to delay the ff_init call in hid-core.c until after this lock has
been released.
Calling hid_device_io_start() releases the lock so the device can be
configured. We also need to call hid_device_io_stop() on exit for the lock to
remain locked while ending the init of the drivers.
[ benjamin.tissoires@redhat.com: imrpoved the changelog a lot ]
Signed-off-by: Jim Keir <jimkeir@oracledbadirect.com>
Reviewed-by: Benjamin.tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use <driver>-$(CONFIG_FOO) syntax to build multipart objects with
optional parts, since all the config options are bool. Also, delete the
obvious comments in the usbhid Makefile.
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Based on code for the US Surface Type Cover 3
from commit be3b16341d
("HID: add support for MS Surface Pro 3 Type Cover"):
Signed-off-by: Alan Wu <alan.c.wu@gmail.com>
Tested-by: Karlis Dreizis <karlisdreizis@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
New Genius MousePen i608X devices have a new id 0x501a instead of the
old 0x5011 so add a new #define with "_2" appended and change required
places.
The remaining two checkpatch warnings about line length
being over 80 characters are present in the original files too and this
patch was made in the same style (no line break).
Just adding a new id and changing the required places should make the
new device work without any issues according to the bug report in the
following url.
This patch was made according to and fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=67111
Signed-off-by: Giedrius Statkevičius <giedrius.statkevicius@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In several hid drivers it is necessary to calculate the length of an
hid_report. This patch exports the existing static function hid_report_len of
hid-core.c as an inline function in hid.h
Signed-off-by: Mathieu Magnaudet <mathieu.magnaudet@enac.fr>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The touchscreen needs the same quirk as the other models.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Reported-by: Bryan Poling <poli0048@umn.edu>
CC: stable@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Yet another device that needs this quirk.
Reported-by: Tanguy de Baritault <tdebaritault@gmail.com>
Signed-off-by: Adel Gadllah <adel.gadllah@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When events occurs while no one is listening to the node (hid->open == 0
and usb_kill_urb() called) some events are still stacked somewhere in
the USB (kernel or device?) stack. When the node gets reopened, these
events are drained, and this results in spurious touch down/up, or mouse
button clicks.
The problem was spotted with touchscreens in fdo bug #81781 [1], but it
actually occurs with any mouse using hid-generic or touchscreen.
A way to reproduce it is to call:
$ xinput disable 9 ; sleep 5 ; xinput enable 9
With 9 being the device ID for the touchscreen/mouse. During the "sleep",
produce some touch events or click events. When "xinput enable" is called,
at least one click is generated.
This patch tries to fix this by draining the queue for 50 msec and
during this time frame, not forwarding these old events to the hid layer.
Hans completed the explanation:
"""
Devices like mice (basically any hid device) will have a fifo
on the device side, when we stop submitting urbs to get hid reports from
it, that fifo will fill up, and when we resume we will get whatever
is there in that fifo.
"""
[1] https://bugs.freedesktop.org/show_bug.cgi?id=81781
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
