The user_skb maybe be leaked if the operation on it failed and codes
skipped into the label "out:" without calling genlmsg_unicast.
Cc: Pravin Shelar <pshelar@nicira.com>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
make defconfig reports:
warning: (NETFILTER_XT_TARGET_LOG) selects NF_LOG_IPV6 which has unmet direct dependencies (NET && INET && IPV6 && NETFILTER && NETFILTER_ADVANCED)
Fixes: d79a61d netfilter: NETFILTER_XT_TARGET_LOG selects NF_LOG_*
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
pull request: Netfilter/IPVS fixes for net
The following patchset contains seven Netfilter fixes for your net
tree, they are:
1) Make the NAT infrastructure independent of x_tables, some users are
already starting to test nf_tables with NAT without enabling x_tables.
Without this patch for Kconfig, there's a superfluous dependency
between NAT and x_tables.
2) Allow to use 0 in the cgroup match, the kernel rejects with -EINVAL
with no good reason. From Daniel Borkmann.
3) Select CONFIG_NF_NAT from the nf_tables NAT expression, this also
resolves another NAT dependency with x_tables.
4) Use HAVE_JUMP_LABEL instead of CONFIG_JUMP_LABEL in the Netfilter hook
code as elsewhere in the kernel to resolve toolchain problems, from
Zhouyi Zhou.
5) Use iptunnel_handle_offloads() to set up tunnel encapsulation
depending on the offload capabilities, reported by Alex Gartrell
patch from Julian Anastasov.
6) Fix wrong family when registering the ip_vs_local_reply6() hook,
also from Julian.
7) Select the NF_LOG_* symbols from NETFILTER_XT_TARGET_LOG. Rafał
Miłecki reported that when jumping from 3.16 to 3.17-rc, his log
target is not selected anymore due to changes in the previous
development cycle to accomodate the full logging support for
nf_tables.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some hosts can be both little and big endian.
In certain scenarios a big endian kernel can kexec a little endian kernel.
This patch fixes this case from both ends:
1) Return endianity to original values on shutdown (in case little endian kernel boots after we shutdown).
2) Do not rely on HW reset values when loading driver in little endian kernel
but configure them explicitly (in case previous kernel was big endian and did not reset the HW).
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When qeth device is queried for ethtool data, hardware operation
is performed to extract the necessary information from the card.
If the card is not online at the moment (e.g. it is undergoing
recovery), this operation produces undesired effects like
temporarily freezing the system. This patch prevents execution
of the hardware query operation when the card is not online.
In such case, ioctl() operation returns error with errno ENODEV.
Reviewed-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: Frank Blaschka <blaschka@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused 'dev' variable from arc_emac_remove(), since it's
not being used any more.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary double parenthesis around if statement.
Signed-off-by: David Wood <devel@dtwood.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calxeda 1G/10G XGMAC Ethernet support should be available only on
Calxeda ECX-1000/2000 (Highbank/Midway) platforms.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Renesas SuperH Ethernet support should be available only on
Renesas ARM SoCs and SuperH architecture.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Magnus Damm <magnus.damm@gmail.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a link is already up, the following sequence makes the kernel
block completely:
ip link set dev eth0 down
ip link set dev eth0 up
This is because on suspended phy, the following lines
__lpc_eth_reset(pldat);
__lpc_eth_init(pldat);
make the LPC ethernet core block (see LPC32x0 manual). The PHY needs to be
(re-)activated low-level first.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch fixes race conditions between PCI error recovery callbacks and
potential ifup/ifdown.
First, if ifup (tg3_open) is called between tg3_io_error_detected() and
tg3_io_resume() then tp->timer is armed twice before expiry. Once during
tg3_open() and again during tg3_io_resume(). This results in BUG
at kernel/time/timer.c:945.
Second, if ifdown (tg3_close) is called between tg3_io_error_detected()
and tg3_io_resume() then tg3_napi_disable() is called twice without
a tg3_napi_enable between. Once during tg3_io_error_detected() and again
during tg3_close(). The tg3_io_resume() then hangs on rtnl_lock().
v2: Added logging messages per Prashant's request
Cc: Prashant Sreedharan <prashant@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel says:
====================
rtnl: send notification in do_setlink()
This series ensures to call the notifier chain and to send a netlink
message when a change is done by do_setlink().
The three first patches mainly prepare the last one, which do this change.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Depending on which parameters were updated, the changes were not propagated via
the notifier chain and netlink.
The new flag has been set only when the change did not cause a call to the
notifier chain and/or to the netlink notification functions.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no functional changes with this commit, it only prepares the next one.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only effect of this patch is to print a warning if IFLA_LINKMODE is updated
and a following change fails.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only effect of this patch is to print a warning if IFLA_TXQLEN is updated
and a following change fails.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sathya Perla says:
====================
be2net: patch set
v2 changes: add a new line after variable declaration in patch 12.
***
Patch 1 adds a few new log messages to help debugging in failure cases.
Patch 2 uses new macros for parsing RX/TX completions and TX wrbs to
help shorten the lines.
Patch 3 adds a description for the RX counter rx_input_fifo_overflow_drop.
Patch 4 adds TX completion error statistics reporting via ethtool.
Patch 5 adds a dma_mapping_error counter and its reporting via ethtool.
Patch 6 fixes up log messages in the Lancer FW download path.
Patch 7 replaces gotos with direct return statements.
Patch 8 cleans up be_change_mtu() code by using a new macro BE_MAX_MTU
Patch 9 makes be_cmd_get_regs() routine to return an integer status
similar to other FW cmd routines in be_cmds.c
Patch 10 gets rid of TX budget as enforcing a budget on TX completion
processing in NAPI is neither suggested nor it provides a performance benefit.
Patch 11 defines and uses a new macro for_all_tx_queues_on_eq() similar
to the RX processing code.
Patch 12 queries max_tx_qs from the FW for BE3 super-nic profiles.
For those profiles, the driver cannot assume a constant BE3_MAX_TX_QS value,
as the value may change for each function.
Please consider applying this patch set to the net-next tree. Thanks!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In the BE3 super-nic profile, the max_tx_qs value can vary for each function.
So the driver needs to query this value from FW instead of using the
pre-defined constant BE3_MAX_TX_QS.
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the for() loop that traverses all the TX queues on an EQ
with the macro for_all_tx_queues_on_eq(). With this expalnatory
name, the one line comment is not required anymore.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enforcing a budget on the TX completion processing in NAPI doesn't
benefit performance in anyway. Just get rid of it.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few failure cases in be_cmd_get_regs() that ideally must return
an error value. This style is used across all the routines in be_cmds.c with
this routine being an exception. This patch fixes this.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch defines a new macro BE_MAX_MTU to make the code in be_change_mtu()
more readable.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In cases where there is no extra code to handle an error, this patch replaces
gotos with a direct return statement.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Log messages in the Lancer FW download path have issues such as:
- a single message spanning multiple lines
- the success message is logged even in failure cases
- status codes are already logged in the FW cmd routines
This patch fixes these issues.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a dma_mapping_error counter to count the number of packets dropped
due to DMA mapping errors.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW reports TX completion errors in TX completion. This patch adds these
counters to ethtool statistics.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AMAP_GET/SET_BITS() macro calls take structure name as a parameter
and hence are long and span more than one line. Replace these calls
with a wrapper macros for RX/Tx compls and TX wrb. This results in fewer
lines and more readable code in be_main.c
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the following log messages to help debugging
failure cases:
1) log FW version number: this is useful when driver initialization
fails and the FW version number cannot be queried via ethtool
2) per function resource limits for BEx chips: these values are
currently being printed only for Skyhawk and Lancer
3) PCI BAR mapping failure
4) function_mode/caps queried from FW: this helps catch any FW bugs
that could advertise wrong capabilities to the driver
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We ran into a case on ppc64 running mariadb where io_getevents would
return zeroed out I/O events. After adding instrumentation, it became
clear that there was some missing synchronization between reading the
tail pointer and the events themselves. This small patch fixes the
problem in testing.
Thanks to Zach for helping to look into this, and suggesting the fix.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Cc: stable@vger.kernel.org
Analogous to commit 8858d88a25
that fixed commit 70b41abc15
"ARM: ux500: move MSP pin control to the device tree"
accidentally activated MSP2, giving rise to a boot scroll
scream as the kernel attempts to probe a driver for it and
fails to obtain DMA channel 14.
For some reason I forgot to fix this on the Snowball. Fix
this up by marking the node disabled again.
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
The driver was not bound checking the received length byte to ensure it was within the
the buffer size that is allocated for SMBus blocks. This resulted in buffer overflows
whenever an invalid length byte was received.
It also failed to ensure the length byte was not zero. If it received zero, it would end up
in an infinite loop as the at91_twi_read_next_byte function returned immediately without
allowing RHR to be read to clear the RXRDY interrupt.
Tested agaisnt a SMBus compliant battery.
Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
In rk3x SOC, the I2C controller can receive/transmit up to 32 bytes data
in one chunk, so the size of data to be write/read to/from TXDATAx/RXDATAx
must be less than or equal 32 bytes at a time.
Tested on rk3288-pinky board, elan receive 158 bytes data.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Acked-by: Max Schwarz <max.schwarz@online.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
There is a race condition in at91_do_twi_xfer when signals arrive.
If a signal is recieved while waiting for a transfer to complete
wait_for_completion_interruptible_timeout() will return -ERESTARTSYS.
This is not handled correctly resulting in interrupts still being
enabled and a transfer being in flight when we return.
Symptoms include a range of oopses and bus lockups. Oopses can happen
when the transfer completes because the interrupt handler will corrupt
the stack. If a new transfer is started before the interrupt fires
the controller will start a new transfer in the middle of the old one,
resulting in confused slaves and a locked bus.
To avoid this, use wait_for_completion_io_timeout instead so that we
don't have to deal with gracefully shutting down the transfer and
disabling the interrupts.
Signed-off-by: Simon Lindgren <simon@aqwary.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
The "clock-frequency" DT property is listed as optional, However,
the current code stores the return value of of_property_read_u32 in
the return code of mv64xxx_of_config, but then forgets to clear it
after setting the default value of "clock-frequency". It is then
passed out to the main probe function, resulting in a probe failure
when "clock-frequency" is missing.
This patch checks and then throws away the return value of
of_property_read_u32, instead of storing it and having to clear it
afterwards.
This issue was discovered after the property was removed from all
sunxi DTs.
Fixes: 4c730a06c1 ("i2c: mv64xxx: Set bus frequency to 100kHz if clock-frequency is not provided")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Cc: stable@vger.kernel.org
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Sometimes the MNR and MST interrupts happen simultaneously (stop automatically
follows NACK, according to the manuals) and in such case the ID_NACK flag isn't
set since the MST interrupt handling precedes MNR and all interrupts are cleared
and disabled then, so that MNR interrupt is never noticed -- this causes NACK'ed
transfers to be falsely reported as successful. Exchanging MNR and MST handlers
fixes this issue, however the MNR bit somehow gets set again even after being
explicitly cleared, so I decided to completely suppress handling of all disabled
interrupts (which is a good thing anyway)...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When intel_tv_detect() fails to do load detection it would forget to
drop the locks and clean up the acquire context. Fix it up.
This is a regression from:
commit 208bf9fdcd
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Mon Aug 11 13:15:35 2014 +0300
drm/i915: Fix locking for intel_enable_pipe_a()
v2: Make the code more readable (Chris)
v3: Drop WARN_ON(type < 0) (Chris)
Cc: stable@vger.kernel.org
Cc: Tibor Billes <tbilles@gmx.com>
Reported-by: Tibor Billes <tbilles@gmx.com>
Tested-by: Tibor Billes <tbilles@gmx.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
commit 0944fe3f4a ("s390/mm: implement software referenced bits")
triggered another paging/storage key corruption. There is an
unhandled invalid->valid pte change where we have to set the real
storage key from the pgste.
When doing paging a guest page might be swapcache or swap and when
faulted in it might be read-only and due to a parallel scan old.
An do_wp_page will make it writeable and young. Due to software
reference tracking this page was invalid and now becomes valid.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: stable@vger.kernel.org # v3.12+
Since 3.12 or more precisely commit 0944fe3f4a ("s390/mm:
implement software referenced bits") guest storage keys get
corrupted during paging. This commit added another valid->invalid
translation for page tables - namely ptep_test_and_clear_young.
We have to transfer the storage key into the pgste in that case.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: stable@vger.kernel.org # v3.12+
commit 39b2bbe3d7
"gpio: add flags argument to gpiod_get*() functions"
added a dynamic flags argument to all the GPIOD getter
functions, however this did not cover the stubs so
when people used gpiod stubs to compile out descriptor
code, compilation failed.
Solve this by:
- Also rename all the stub functions __gpiod_*
- Moving the vararg hack outside of #ifdef CONFIG_GPIOLIB
so these will always be available.
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As the race condition on the inode cache, following scenario can appear:
[Thread a] [Thread b]
->f2fs_mkdir
->f2fs_add_link
->__f2fs_add_link
->init_inode_metadata failed here
->gc_thread_func
->f2fs_gc
->do_garbage_collect
->gc_data_segment
->f2fs_iget
->iget_locked
->wait_on_inode
->unlock_new_inode
->move_data_page
->make_bad_inode
->iput
When we fail in create/symlink/mkdir/mknod/tmpfile, the new allocated inode
should be set as bad to avoid being accessed by other thread. But in above
scenario, it allows f2fs to access the invalid inode before this inode was set
as bad.
This patch fix the potential problem, and this issue was found by code review.
change log from v1:
o Add condition judgment in gc_data_segment() suggested by Changman Lee.
o use iget_failed to simplify code.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Hariprasad Shenai says:
====================
Trivial fixes for cxgb4
This patch series adds support to fix T5 adapter accessing T4 adapter registers,
issue mbox command on correct mbox for physical function, avoid dumping write
only registers, use correct length for adapter part number and support to detect
and display firmware reported errors.
The patches series is created against 'net' tree.
And includes patches on cxgb4 driver.
We have included all the maintainers of respective drivers. Kindly review the
change and let us know in case of any review comments.
Thanks
V2:
Added description for each patch as per David Miller's comment
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
A couple of RDMA-related called to t4_query_params() were issuing mbox commands
on mbox0 instead of mbox4.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid dumping MPS_RPLC_MAP_CTL for reg dumps; this is a Write-Only register.
Reading this register may cause MPS TCAM corruption.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The adapter firmware can indicate error conditions to the host.
If the firmware has indicated an error, print out the reason for
the firmware error.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes few register access for both T4 and T5.
PCIE_CORE_UTL_SYSTEM_BUS_AGENT_STATUS & PCIE_CORE_UTL_PCI_EXPRESS_PORT_STATUS
is T4 only register don't let T5 access them. For T5 MA_PARITY_ERROR_STATUS2
is additionally read. MPS_TRC_RSS_CONTROL is T4 only register, for T5 use
MPS_T5_TRC_RSS_CONTROL.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously it was using the length value of serial number.
Also added macro for VPD unique identifier (0x82).
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We previously assumed that a Port's Capabilities and Advertised Capabilities
would never change from Port Initialization time. This is no longer true
when we can have 10Gb/s and 1Gb/s SFP+ Transceiver Modules randomly swapped.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
