This patch (as1156) straightens out some code in usbcore. The
usb_create_intf_ep_files() and usb_remove_intf_ep_files() routines
don't need to be separate inlines; they should be moved bodily into
the places where they get used.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There's no need to take the address of the function params or local variables
when the direct value byteswapping routines are available.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This will let us use this header in other header files.
Will be needed for the FHCI USB Host driver.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver implements the support for Oxford OXU210HP USB high-speed host,
no peripheral nor OTG.
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
Cc: Kan Liu <kan.k.liu@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For function ehci_bus_resume()
- Added flag resume_needed
No need to wait for 20ms if no port was suspended
- Change mdelay to msleep
- release and reacquire the spinlock around mdelay
Signed-off-by: vikram pandita <vikram.pandita@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use the newly introduced pci_ioremap_bar() function in drivers/usb.
pci_ioremap_bar() just takes a pci device and a bar number, with the goal
of making it really hard to get wrong, while also having a central place
to stick sanity checks.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
temp, bytes and param->{length,sglen,vary} are unsigned so
these tests do nothing.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch corrects the issue when one connects a Nokia 5200 cell
phone in data storage mode. If one uses an unpatched unusual_devs.h,
the following messages appear on /var/log/messages:
Dec 12 01:03:24 alberich kernel: usb 4-2: new full speed USB device
using uhci_hcd and address 3
Dec 12 01:03:25 alberich kernel: usb 4-2: configuration #1 chosen from 1 choice
Dec 12 01:03:25 alberich kernel: scsi10 : SCSI emulation for USB Mass
Storage devices
Dec 12 01:03:25 alberich kernel: usb 4-2: New USB device found,
idVendor=0421, idProduct=04bd
Dec 12 01:03:25 alberich kernel: usb 4-2: New USB device strings:
Mfr=1, Product=2, SerialNumber=3
Dec 12 01:03:25 alberich kernel: usb 4-2: Product: Nokia 5200
Dec 12 01:03:25 alberich kernel: usb 4-2: Manufacturer: Nokia
Dec 12 01:03:25 alberich kernel: usb 4-2: SerialNumber: 353930018354523
Dec 12 01:03:25 alberich kernel: usbcore: registered new interface driver ub
Dec 12 01:03:30 alberich kernel: scsi 10:0:0:0: Direct-Access
Nokia Nokia 5200 0000 PQ: 0 AN
SI: 4
Dec 12 01:03:30 alberich kernel: sd 10:0:0:0: [sdg] 3985409 512-byte
hardware sectors (2041 MB)
Dec 12 01:03:30 alberich kernel: sd 10:0:0:0: [sdg] Write Protect is off
Dec 12 01:03:30 alberich kernel: sd 10:0:0:0: [sdg] Assuming drive
cache: write through
Dec 12 01:03:30 alberich kernel: sd 10:0:0:0: [sdg] 3985409 512-byte
hardware sectors (2041 MB)
Dec 12 01:03:30 alberich kernel: sd 10:0:0:0: [sdg] Write Protect is off
Dec 12 01:03:30 alberich kernel: sd 10:0:0:0: [sdg] Assuming drive
cache: write through
Dec 12 01:03:30 alberich kernel: sdg: sdg1
Dec 12 01:03:30 alberich kernel: sd 10:0:0:0: [sdg] Attached SCSI removable disk
Dec 12 01:03:30 alberich kernel: sd 10:0:0:0: Attached scsi generic sg9 type 0
Dec 12 01:03:30 alberich kernel: sd 10:0:0:0: [sdg] Sense Key : No
Sense [current]
Dec 12 01:03:30 alberich kernel: sd 10:0:0:0: [sdg] Add. Sense: No
additional sense information
Dec 12 01:03:30 alberich kernel: sd 10:0:0:0: [sdg] Sense Key : No
Sense [current]
Dec 12 01:03:30 alberich kernel: sd 10:0:0:0: [sdg] Add. Sense: No
additional sense information
Dec 12 01:03:30 alberich kernel: sd 10:0:0:0: [sdg] Sense Key : No
Sense [current]
(...)
The MicroSD card in the phone remains inaccessible and finally the
cell phone turns itself off. The patch solves this problem and makes
the cell phone fully accessible:
[root@alberich kernel-linus-2.6.27.5-1mdv]# df -h
Sist. Arq. Tam Usad Disp Uso% Montado em
/dev/sda6 31G 5,2G 26G 17% /
/dev/sda1 92M 27M 61M 31% /boot
/dev/mapper/homevg-homelv 240G 237G 3,5G 99% /home
/dev/sda3 21G 7,9G 13G 40% /mnt/windows
/dev/sdg1 2,0G 287M 1,7G 15% /media/disk <--------
I've found necessary to use the FL_US_CAPACITY_FIX switch, as without
it the cell phone is recognized but it went berserk when performing
low-level functions on it (a fdisk -l /dev/uba for example).
lsusb -v output follows:
Bus 004 Device 004: ID 0421:04bd Nokia Mobile Phones
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0421 Nokia Mobile Phones
idProduct 0x04bd
bcdDevice 6.03
iManufacturer 1 Nokia
iProduct 2 Nokia 5200
iSerial 3 353930018354523
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 32
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xc0
Self Powered
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk (Zip)
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Device Status: 0x0001
Self Powered
Signed-off-by: Paulo Afonso Graner Fessel <pfessel@gmail.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This device has been released in a new revision which is still buggy.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I have another Argosy USB storage device, which has the same problem
with the Argosy USB storage device already fixed in 2.6.27.7. But this
device has another product ID (840:84), so this patch adds a new entry
into unusual_devs to fix the mount problem.
I enclose here two patches: one against 2.6.27.8, and another against
the latest linus-git tree.
The information about the Argosy device is like below:
#lsusb -v -d 840:84
Bus 005 Device 005: ID 0840:0084 Argosy Research, Inc.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0840 Argosy Research, Inc.
idProduct 0x0084
bcdDevice 0.01
iManufacturer 1 Generic
iProduct 2 USB 2.0 Storage Device
iSerial 3 8400000000002549
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 32
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xc0
Self Powered
MaxPower 2mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk (Zip)
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)
Before the patch, dmesg returns a lot of information like below (my
dmesg is overflown):
....
[ 138.833390] sd 7:0:0:0: [sdb] Add. Sense: No additional sense information
[ 138.877631] sd 7:0:0:0: [sdb] Sense Key : No Sense [current]
[ 138.877643] sd 7:0:0:0: [sdb] Add. Sense: No additional sense information
[ 138.921906] sd 7:0:0:0: [sdb] Sense Key : No Sense [current]
[ 138.921923] sd 7:0:0:0: [sdb] Add. Sense: No additional sense information
....
After the fix, dmesg returns below information:
....
usb 5-1: new high speed USB device using ehci_hcd and address 5
usb 5-1: configuration #1 chosen from 1 choice
scsi7 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 5
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
scsi 7:0:0:0: Direct-Access HTS54808 0M9AT00 MG4O PQ: 0 ANSI: 0
sd 7:0:0:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 7:0:0:0: [sdb] Write Protect is off
sd 7:0:0:0: [sdb] Mode Sense: 03 00 00 00
sd 7:0:0:0: [sdb] Assuming drive cache: write through
sd 7:0:0:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 7:0:0:0: [sdb] Write Protect is off
sd 7:0:0:0: [sdb] Mode Sense: 03 00 00 00
sd 7:0:0:0: [sdb] Assuming drive cache: write through
sdb: sdb1
sd 7:0:0:0: [sdb] Attached SCSI disk
sd 7:0:0:0: Attached scsi generic sg1 type 0
kjournald starting. Commit interval 5 seconds
EXT3 FS on sdb1, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Cc: Kuniyasu Suzaki <k.suzaki@aist.go.jp>
Signed-off-by: Nguyen Anh Quynh <aquynh@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As suggested by Linus: Don't do the libata init in 2 separate
steps with a global sync inbetween, but do it as one async step,
with a local sync before registering the device.
This cuts the boottime on my machine with 2 sata controllers down
significantly, and it seems to work. Would be nice if the libata
folks take a good look at this patch though..
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
This patch makes the libata port scanning asynchronous (per device).
There is a synchronization point before doing the actual disk scan
so that device ordering is not affected.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
This patch makes part of the scsi probe (which is mostly device spin up and the
partition scan) asynchronous. Only the part that runs after getting the device
number allocated is asynchronous, ensuring that device numbering remains stable.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Check for ACPI resource conflicts in hwmon drivers. I've included
all Super-I/O and PCI drivers.
I've voluntarily left out:
* Vendor-specific drivers: if they conflicted on any system, this would
pretty much mean that they conflict on all systems, and we would know
by now.
* Legacy ISA drivers (lm78 and w83781d): they only support chips found
on old designs were ACPI either wasn't supported or didn't deal with
thermal management.
* Drivers accessing the I/O resources indirectly (e.g. through SMBus):
the checks are already done where they belong, i.e. in the bus drivers.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: David Hubbard <david.c.hubbard@gmail.com>
The Texas Instruments TMP121 is a SPI temperature sensor very similar
to the LM70, with slightly higher resolution. This patch extends the
LM70 driver to support the TMP121. The TMP123 differs in pin assign-
ment.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This fixes a byteswap bug in the LM70 temperature sensor driver,
which was previously covered up by a converse bug in the driver
for the LM70EVAL-LLP board (which is also fixed).
Other fixes: doc updates, remove an annoying msleep(), and improve
three-wire protocol handling.
Signed-off-by: Kaiwan N Billimoria <kaiwan@designergraphix.com>
[ dbrownell@users.sourceforge.net: doc and whitespace tweaks ]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Now that the new merged fschmd driver has gained support for the watchdog
integrated into these IC's, there is no more reason to keep the old fscher
and fscpos drivers around, so mark them as deprecated.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch adds support for the watchdog part found in _all_ supported FSC
sensor chips.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Various small cleanups in preparation of adding watchdog support,
mostly removing _MASK postfix from defines which are not masks.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
It turns out that we cannot create a pci_driver in this driver because PCI will
not call this module's probe function if the i5000-edac driver is already
loaded. That said, we only want one value (AMBASE) from the PCI config space.
Neither driver alters this value, so it's safe to read it. However, we still
want the module aliases, so provide that.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Allow it87.c to handle IT8720 chipset like IT8718 in order to
retrieve voltage, temperatures and fans speed from sensors
tools. Also updating the related documentation.
Signed-off-by: Jean-Marc Spaggiari <jean-marc@spaggiari.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
I2C_CLIENT_MODULE_PARM is overkill for force_subclients. We really
only use 4 out of the 48 slots, so we're better defining a custom
variable instead. This change saves 92 bytes of data for each of the
five drivers affected.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Marc Hulsman <m.hulsman@tudelft.nl>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Add Linux support for the Linear Technology LTC4245 Multiple Supply Hot
Swap controller I2C monitoring interface.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The RPM after conversion from / before conversion to a register value can be
much more than 65535 (up to 1500000), so putting this into an u16 can cause
overflows. This changes the functions to use an int to store / get RPM instead.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Print the mode (duty-cycle or RPM) of each fan on driver load.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add some documentation about the f71882fg driver, and update the Kconfig
documentation to report the new supported models.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Adjust auto_channels_temp show and store functions for different numbering of
temps between f8000 and other supported models.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
For some reason the fan_attr array for the f71862fg was missing the attr for
the 3th pwm output. This patch fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
And (finally) the patch actually adding f8000 support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Remove the fan_mode module option it was a monstrosity to begin with, and
when adding support for the F8000 it becomes a real pain!
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
While studying the datasheets for adding F8000 support, I noticed that the
F718x2 has separate alarms (and beep control) for its max and crit limits.
We keep the temp#_alarm attributes as they are, even though it would be more
logical to rename them to temp#_max_alarm. Because lm_sensors v2 depends
on them.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
More F8000 prep work. Take over the checking if the hwmon part is not
powered down from the standalone f8000 driver.
This check is valid for all supported models.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Simplify fan and temp hyst. handling by treating the registers as an array of
nibbles instead of using switch cases. Also unify the way hysts are handled
between temp and fans, the temp code was storing the actual per temp hyst
values in 4 u8's, where as the fan code was storing actual register values.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
While working on adding F8000 support I noticed that various of the
store sysfs functions (and a few of the show also) had issues.
This patch fixes the following issues in these functions:
* store: storing the result of strto[u]l in an int, resulting in a possible
overflow before boundary checking
* store: use of f71882fg_update_device(), we don't want to read the whole
device in store functions, just the registers we need
* store: use of cached register values instead of reading the needed regs
in the store function, including cases where f71882fg_update_device() was
not used, this could cause real isues
* show: shown value is a calculation of 2 or more cached register reads,
without locking the data struct.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch is a preparation patch for adding F8000 support to the f71882fg
driver. If you look at the register addresses and esp, the bits used for
the temperature channels, then you will notice that it appears that they
start at 1 in a system meant to start at 0. As the F8000 actually uses the 0
addresses and bits, this patch changes the f71882fg driver to take 4
temperatures numbered 0-3 in to account, using 1-3 in this new scheme for
the temperatures actually present in the F718x2FG.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The f71882fg driver did some io to ioports it hadn't reserved yet in its
find (detect) function, this patches moves this io to the probe function
where these ports are reserved and this io belongs.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch adds support for the Fintek f71862fg superio monitoring
functions to the f71882fg driver.
This support has been tested without problems on a Jetway J9F2 by
Tony McConnell.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Various small cleanups as preparation for adding f71862fg support to the
f71882fg driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add PWM (fan speed control) support to the f71882fg driver. Both
manual control and automatic (temperature-based) modes are supported.
Additionally, each mode has a PWM-based and an RPM-based variant. By
default we use the mode set by the BIOS.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: Mark van Doesburg <mark.vandoesburg@hetnet.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
A few cleanups that were originally part of a larger patch but are
better submitted separately.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: Mark van Doesburg <mark.vandoesburg@hetnet.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Convert f71882fg driver from SENSOR_ATTR to SENSOR_ATTR2 use, this is a
preparation patch for adding pwm support, which is broken out to make what
changes really in the pwm support patch clear.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: Mark van Doesburg <mark.vandoesburg@hetnet.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Convert the apanel driver to the new i2c device driver binding model,
as the legacy model is going away soon. In the new model, the apanel
driver is no longer scanning all the i2c adapters, instead the
relevant bus driver (i2c-i801) is instantiating the device as needed.
One side benefit is that the apanel driver will now load automatically
on all systems where it is needed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
There are a number of drivers which set their i2c bus class to
I2C_CLASS_CAM_DIGITAL, however no chip driver actually checks for this
flag, so we might as well drop it now.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
I2C_CLASS_ALL is almost never what bus driver authors really want.
These i2c classes are really only about which devices must be probed,
not what devices can be present. As device drivers get converted to the
new i2c device driver model, only a few device types will keep relying
on probing.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Use dev_name(dev) instead of accessing dev.bus_id directly, as the
latter is going away soon.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Kay Sievers <kay.sievers@vrfy.org>
This patch is part of a larger patch series which will remove
the "char bus_id[20]" name string from struct device. The device
name is managed in the kobject anyway, and without any size
limitation, and just needlessly copied into "struct device".
To set and read the device name dev_name(dev) and dev_set_name(dev)
must be used. If your code uses static kobjects, which it shouldn't
do, "const char *init_name" can be used to statically provide the
name the registered device should have. At registration time, the
init_name field is cleared, to enforce the use of dev_name(dev) to
access the device name at a later time.
We need to get rid of all occurrences of bus_id in the entire tree
to be able to enable the new interface. Please apply this patch,
and possibly convert any remaining remaining occurrences of bus_id.
We want to submit a patch to -next, which will remove bus_id from
"struct device", to find the remaining pieces to convert, and finally
switch over to the new api, which will remove the 20 bytes array
and does no longer have a size limitation.
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* 'drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm: fix ordering of driver unload vs agp unload.
drm/i915: Respect the other stolen memory sizes we know of.
drm/i915: Non-mobile parts don't have integrated TV-out.
drm/i915: Add support for integrated HDMI on G4X hardware.
drm/i915: Pin cursor bo and unpin old bo when setting cursor.
drm/i915: Don't allow objects to get bound while VT switched.
This is ported directly from the userland 2D driver code. The HDMI audio bits
aren't hooked up yet.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
We also didn't track the cursor bo before and would leak a reference
when the cursor image was change.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This avoids a BUG_ON in the enter_vt path due to objects being in the GTT
when we shouldn't have ever let them be (as we're not supposed to touch the
device during that time).
This was triggered by a change in the 2D driver to use the GTT mapping of
objects after pinning them to improve software fallback performance.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (29 commits)
Input: i8042 - add Dell Vostro 1510 to nomux list
Input: gtco - use USB endpoint API
Input: add support for Maple controller as a joystick
Input: atkbd - broaden the Dell DMI signatures
Input: HIL drivers - add MODULE_ALIAS()
Input: map_to_7segment.h - convert to __inline__ for userspace
Input: add support for enhanced rotary controller on pxa930 and pxa935
Input: add support for trackball on pxa930 and pxa935
Input: add da9034 touchscreen support
Input: ads7846 - strict_strtoul takes unsigned long
Input: make some variables and functions static
Input: add tsc2007 based touchscreen driver
Input: psmouse - add module parameters to control OLPC touchpad delays
Input: i8042 - add Gigabyte M912 netbook to noloop exception table
Input: atkbd - Samsung NC10 key repeat fix
Input: atkbd - add keyboard quirk for HP Pavilion ZV6100 laptop
Input: libps2 - handle 0xfc responses from devices
Input: add support for Wacom W8001 penabled serial touchscreen
Input: synaptics - report multi-taps only if supported by the device
Input: add joystick driver for Walkera WK-0701 RC transmitter
...
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (41 commits)
scc_pata: make use of scc_dma_sff_read_status()
ide-dma-sff: factor out ide_dma_sff_write_status()
ide: move read_sff_dma_status() method to 'struct ide_dma_ops'
ide: don't set hwif->dma_ops in init_dma() method
Resurrect IT8172 IDE controller driver
piix: sync ich_laptop[] with ata_piix.c
ide: update warm-plug HOWTO
ide: fix ide_port_scan() to do ACPI setup after initializing request queues
ide: remove now redundant ->cur_dev checks
ide: remove unused ide_hwif_t.sg_mapped field
ide: struct ide_atapi_pc - remove unused fields and update documentation
ide: remove superfluous hwif variable assignment from ide_timer_expiry()
ide: use ide_pci_is_in_compatibility_mode() helper in setup-pci.c
ide: make "paranoia" ->handler check in ide_intr() more strict
ide-cd: convert to ide-atapi facilities
ide-cd: start DMA before sending the actual packet command
ide-cd: wait for DRQ to get set per default
ide: Fix drive's DWORD-IO handling
ide: add port and host iterators
ide: dynamic allocation of device structures
...
Use del_timer_sync() instead of del_timer() to make sure the timer won't
be running when we return from parport_wait_event(), because this would
crash due to destruction of timer_list.
This is untested and just based on a code review. Just think about the
following sequence of events:
- add_timer()
- down_interruptible() is interrupted by a signal.
- we enter the timer callback handler on another CPU.
- del_timer(), but the timer callback is still running.
- eturn from parport_wait_even, which destroys the automatic variable
"timer" while the callback is running on another CPU.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All other compatibles that are uniquely identifying the processor use a
prefix of the form fsl,mpc85...'. We add support for it so we can
deprecate the older 'fsl,85...' that was improperly used here.
Additionally added mpc8536 & mpc8560 to the compatible lists.
This patch is based on Nate's 8572 patch.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Acked-by: Dave Jiang <djiang@mvista.com>
Cc: Nate Case <ncase@xes-inc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch is part of a larger patch series which will remove the "char
bus_id[20]" name string from struct device. The device name is managed in
the kobject anyway, and without any size limitation, and just needlessly
copied into "struct device".
[akpm@linux-foundation.org: coding-style fixes]
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the newly introduced pci_ioremap_bar() function in drivers/edac.
pci_ioremap_bar() just takes a pci device and a bar number, with the goal
of making it really hard to get wrong, while also having a central place
to stick sanity checks.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As a non-atomic value, it's only safe to look at entropy_count when the
pool lock is held, so we move the BUG_ON inside the lock for correctness.
Also remove the spurious comment. It's ok for entropy_count to
temporarily exceed POOLBITS so long as it's left in a consistent state
when the lock is released.
This is a more correct, simple, and idiomatic fix for the bug in
8b76f46a2d. I've left the reorderings introduced by that patch in place
as they're harmless, even though they don't properly deal with potential
atomicity issues.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove excess kernel-doc notation from rio header and driver:
Warning(include/linux/rio_drv.h:399): Excess function parameter or struct member 'buffer' description in 'rio_get_inb_message'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The code to draw penguin logos always uses some properties of the main logo.
This is incorrect if additional logos (CONFIG_FB_LOGO_EXTRA=y) have different
types than the main logo, which causes corrupted logo images.
http://bugzilla.kernel.org/show_bug.cgi?id=12181
Hence skip additional logos that are not compatible with the main logo.
Technically, it's possible to draw multiple logos of different types on
truecolor displays, but this would complicate the (already quite
complicated) logo drawing code even more.
This patch fixes a problem with Debian's linux-image-2.6.26-1-powerpc64
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=508173
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
unsigned ptr cannot be negative
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix this sparse warnings:
drivers/video/neofb.c:1456:4: warning: returning void-valued expression
drivers/video/neofb.c:1464:3: warning: returning void-valued expression
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix this sparse warning:
drivers/video/pm3fb.c:543:3: warning: returning void-valued expression
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix this sparse warnings:
drivers/video/nvidia/nv_accel.c:304:3: warning: returning void-valued expression
drivers/video/nvidia/nv_accel.c:323:3: warning: returning void-valued expression
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
unsigned var->pixclock cannot be less than 0
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When I viewed drivers/video/modedb.c, I noticed a very old typo already
contained in 2.6.0.
This typo remained unheeded at least 5 years. Clear evidence of its
importance. ;)
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the newly introduced pci_ioremap_bar() function in drivers/video.
pci_ioremap_bar() just takes a pci device and a bar number, with the goal
of making it really hard to get wrong, while also having a central place
to stick sanity checks.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Minor updates to the pca953x GPIO expander driver: handle several more
compatible parts, and stop assuming that the I2C layer's return codes are
garbage (that's now been fixed).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Provide a static debounce configuration mechanism for twl4030 GPIOs,
replacing the previous dynamic one. The single user of that mechanism was
for MMC card detect debouncing.
Boards can provide a bitmask saying which GPIOs to debounce (30 msec).
It's always enabled for pins with the MMC card-detect/VMMCx link active,
so most boards won't need to set the debounce mask.
This is a net code shrink, including runtime footprint.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rtc is clearly does not satisfy IS_ERR at the point where it is tested, so
I have changed the test to consider the just initialized rtc->rtc_dev.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@match exists@
expression x, E;
identifier fld;
position p1,p2;
@@
(
x = E;
|
x = E
|
x@p1->fld
... when != x = E
IS_ERR(x@p2)
... when any
)
@other_match exists@
expression match.x, E1, E2;
position match.p1,match.p2;
@@
x = E1
... when != x = E2
when != x@p1
x@p2
@ script:python depends on !other_match@
p1 << match.p1;
p2 << match.p2;
@@
print "* file %s dereference %s test %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Driver for the on-chip RTC found in some of Marvell's SoCs such as the
Kirkwood 88F6281 and 88F6192 devices.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes a few issues with the rtc-ds1216 driver
- use rtc_valid_tm
- use platform_driver_probe
- fix init sequence - it was using rtc_unregister_driver where not
needed. I also added resource_size and removed an useless pointer
assignment.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Tested-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Drivers should only need to implement either set_mmss (counter based RTCs)
or set_time (most RTCs). The RTC subsystem will handle them
appropriately.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- no changelogs in code
- no banners
- use local buffers
- fix probe sequence
- do not init .driver.bus
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Dennis Aberilla <denzzzhome@yahoo.com>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove double spaces and adds some suggestions. It also fixes the
descriptions of options that are no more available as modules.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Small fixes for the ds1390 driver
- fixed initialization of the spi device
- added missing includes
- removed printks
- removed useless wrappers for rtc ops
- removed dead code
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Mark Jackson <mpfj@mimc.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Small fixes for the pxa27x/pxa3xx driver
- use platform_driver_probe
- fixed exit paths
- fixed probe sequence
- added missing include
- using linux/io.h instead of asm/io.h
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With PXA27x and above, a new RTC hardware block was added in addition to
the legacy one which is also found on the SA1100 SOC family. This second
RTC block is called "wristwatch" and "periodic interrupt" and works
independently from the other RTC block.
The driver offers provides :
- a 1Hz ticking clock
- a periodic alarm, in the 1Hz to 1000Hz range
- a one shot alarm
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the power of 2 check on frequencies down into individual rtc drivers
This is to allow for non power of 2 real time clock periodic interrupts
such as those on the pxa27x to be found in the new pxa27x-rtc driver
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes a bunch of irq checking misuses. Most drivers were
getting irq via platform_get_irq(), which returns -ENXIO or r->start.
rtc-cmos.c is special. It is using PNP and platform bindings. Hopefully
nobody is using PNP IRQ 0 for RTC. So the changes should be safe.
rtc-sh.c is using platform_get_irq, but was storing a result into an
unsigned type, then was checking for < 0. This is fixed now.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Blackfin platforms do not support the hardware which this driver drives.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove excess kernel-doc function parameter notation from i2o/.
Warning(drivers/message/i2o/iop.c:64): Excess function parameter 'msg' description in 'i2o_msg_get_wait'
Warning(drivers/message/i2o/device.c:62): Excess function parameter 'drv' description in 'i2o_device_claim'
Warning(drivers/message/i2o/device.c:95): Excess function parameter 'drv' description in 'i2o_device_claim_release'
Warning(drivers/message/i2o/driver.c:186): Excess function parameter 'msg' description in 'i2o_driver_dispatch'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In each case, if the NULL test is necessary, then the dereference should be
moved below the NULL test.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T;
expression E;
identifier i,fld;
statement S;
@@
- T i = E->fld;
+ T i;
... when != E
when != i
if (E == NULL) S
+ i = E->fld;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change the spi_s3c2410 driver to use the generic gpio calls that are now
available.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This solves several issues:
* It fixes the wrong idle clock polarity issue in a cleaner and less
expensive way.
* It handles the AT32AP7000 errata "SPI Chip Select 0 BITS field
overrides other Chip Selects". Other chips, e.g. AT91SAM9261, have
similar issues.
Currently, the AT91RM9200 code path is left alone. But it might be
interesting to try the same technique on RM9200 using a different CSR
register.
[dbrownell@users.sourceforge.net: restore debug message for activation]
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, we have a flag called "new_1" which is basically equivalent
to cpu_is_at91rm9200(). The latter is also called directly a few places.
Clean up this mess by introducing a atmel_spi_v2() function for
determining the controller version, and move all version dependent code
over to use it. This allows us to remove the new_1 flag.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Generalize the old at91rm9200 "bootstrap" bitbanging SPI master driver as
"spi_gpio", so it works with arbitrary GPIOs and can be configured through
platform_data. Such SPI masters support:
- any number of bus instances (bus_num is the platform_device.id)
- any number of chipselects (one GPIO per spi_device)
- all four SPI_MODE values, and SPI_CS_HIGH
- i/o word sizes from 1 to 32 bits;
- devices configured as with any other spi_master controller
When configured using platform_data, this provides relatively low clock
rates. On platforms that support inlined GPIO calls, significantly
improved transfer speeds are also possible with a semi-custom driver.
(It's still painful when accessing flash memory, but less so.)
Sanity checked by using this version to replace both native controllers on
a board with six different SPI slaves, relying on three different
SPI_MODE_* values and both SPI_CS_HIGH settings for correct operation.
[akpm@linux-foundation.org: cleanups]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Magnus Damm <damm@igel.co.jp>
Tested-by: Magnus Damm <damm@igel.co.jp>
Cc: Torgil Svensson <torgil.svensson@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add missing kernel-doc notation:
drivers/firmware/dmi_scan.c:475: No description found for parameter 'str'
drivers/firmware/dmi_scan.c:592: No description found for parameter 'f'
drivers/firmware/dmi_scan.c:592: No description found for parameter 'str'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add temperature sensor support for MacBook Air 2.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
of_node_put is needed before discarding a value received from
of_find_node_by_name, eg in error handling code or when the device node is
no longer used.
The semantic match that catches the bug is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression struct device_node *n;
position p1, p2;
struct device_node *n1;
statement S;
identifier f;
expression E;
expression *ptr != NULL;
@@
n@p1 = of_find_node_by_name(...)
...
if (!n) S
... when != of_node_put(n)
when != n1 = f(n,...)
when != E = n
when any
when strict
(
return \(0\|<+...n...+>\|ptr\);
|
return@p2 ...;
|
of_node_put(n);
|
n1 = f(n,...)
|
E = n
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s of_find_node_by_name %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Nicolas Palix <npalix@diku.dk>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It turns out that the adt7470's automatic fan control algorithm only works
when the temperature sensors get updated. This in turn happens only when
someone tells the chip to read its temperature sensors. Regrettably, this
means that we have to drive the chip periodically.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The adt7470 driver currently assumes that 1s is the proper time to wait to
read all temperature sensors. However, the correct time is 200ms *
number_of_sensors. This patch sets the default time to provide for 10
sensors and then lowers it based on the number of sensor inputs that have
nozero values.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the small window that it takes to read the temperature sensors, the pwm
outputs momentarily drop to 0. This causes a noticeable hiccup in fan
speed, which is slightly annoying. The solution is to manually program
the pwm output with whatever the automatic value is and then shift the
fans to manual control while reading temperatures. Once that is done, put
the fans back to whatever mode of control was there before.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Modify some hwmon drivers to use DIV_ROUND_CLOSEST instead of bloating
source with (naughty) macros.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eliminate sysrq terse help mode; make sysrq help messages more meaningful
(more explicit/verbose). Make the sysrq action letter clearer by listing
it explicitly in more sysrq help messages (when it is not simple/clear).
The SysRq help message now looks like this:
SysRq : HELP : loglevel(0-9) reBoot terminate-all-tasks(E) memory-full-oom-kill(F) kill-all-tasks(I) saK show-backtrace-all-active-cpus(L) show-memory-usage(M) nice-all-RT-tasks(N) powerOff show-registers(P) show-all-timers(Q) unRaw Sync show-task-states(T) Unmount show-blocked-tasks(W)
Addresses http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=330403.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: <jidanni@jidanni.org>
Cc: <330403@bugs.debian.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While looking at reducing the amount of architecture namespace pollution
in the generic kernel, I found that asm/irq.h is included in the vast
majority of compilations on ARM (around 650 files.)
Since asm/irq.h includes a sub-architecture include file on ARM, this
causes a negative impact on the ccache's ability to re-use the build
results from other sub-architectures, so we have a desire to reduce the
dependencies on asm/irq.h.
It turns out that a major cause of this is the needless include of
linux/hardirq.h into asm-generic/local.h. The patch below removes this
include, resulting in some 250 to 300 files (around half) of the kernel
then omitting asm/irq.h.
My test builds still succeed, provided two ARM files are fixed
(arch/arm/kernel/traps.c and arch/arm/mm/fault.c) - so there may be
negative impacts for this on other architectures.
Note that x86 does not include asm/irq.h nor linux/hardirq.h in its
asm/local.h, so this patch can be viewed as bringing the generic version
into line with the x86 version.
[kosaki.motohiro@jp.fujitsu.com: add #include <linux/irqflags.h> to acpi/processor_idle.c]
[adobriyan@gmail.com: fix sparc64]
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Modify ioc4 to always load the sgiioc4 IDE module if the board carrying
the IOC4 hardware actually implements the IDE interface (not all boards
bring this functionality off the IOC4 chip). A drive hosted on the IDE
interface may contain the root filesystem, and sgiioc4 doesn't load
automatically as ioc4 owns the PCI device ID, not sgiioc4.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: Brent Casavant <bcasavan@sgi.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
f_op->poll is the only vfs operation which is not allowed to sleep. It's
because poll and select implementation used task state to synchronize
against wake ups, which doesn't have to be the case anymore as wait/wake
interface can now use custom wake up functions. The non-sleep restriction
can be a bit tricky because ->poll is not called from an atomic context
and the result of accidentally sleeping in ->poll only shows up as
temporary busy looping when the timing is right or rather wrong.
This patch converts poll/select to use custom wake up function and use
separate triggered variable to synchronize against wake up events. The
only added overhead is an extra function call during wake up and
negligible.
This patch removes the one non-sleep exception from vfs locking rules and
is beneficial to userland filesystem implementations like FUSE, 9p or
peculiar fs like spufs as it's very difficult for those to implement
non-sleeping poll method.
While at it, make the following cosmetic changes to make poll.h and
select.c checkpatch friendly.
* s/type * symbol/type *symbol/ : three places in poll.h
* remove blank line before EXPORT_SYMBOL() : two places in select.c
Oleg: spotted missing barrier in poll_schedule_timeout()
Davide: spotted missing write barrier in pollwake()
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Ron Minnich <rminnich@sandia.gov>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Brad Boyer <flar@allandria.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Roland McGrath <roland@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Several subsystem open handlers dereference the fops_get() return value
without checking it for nullness. This opens a race condition between the
open handler and module unloading.
A module can be marked as being unloaded (MODULE_STATE_GOING) before its
exit function is called and gets the chance to unregister the driver.
During that window open handlers can still be called, and fops_get() will
fail in try_module_get() and return a NULL pointer.
This change checks the fops_get() return value and returns -ENODEV if NULL.
Reported-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Acked-by: Takashi Iwai <tiwai@suse.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Dave Airlie <airlied@linux.ie>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the newly introduced pci_ioremap_bar() function in drivers/misc.
pci_ioremap_bar() just takes a pci device and a bar number, with the goal
of making it really hard to get wrong, while also having a central place
to stick sanity checks.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sparse output following warnings.
mm/vmalloc.c:1436:6: warning: symbol 'vread' was not declared. Should it be static?
mm/vmalloc.c:1474:6: warning: symbol 'vwrite' was not declared. Should it be static?
However, it is used by /dev/kmem. fixed here.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Show node to memory section relationship with symlinks in sysfs
Add /sys/devices/system/node/nodeX/memoryY symlinks for all
the memory sections located on nodeX. For example:
/sys/devices/system/node/node1/memory135 -> ../../memory/memory135
indicates that memory section 135 resides on node1.
Also revises documentation to cover this change as well as updating
Documentation/ABI/testing/sysfs-devices-memory to include descriptions
of memory hotremove files 'phys_device', 'phys_index', and 'state'
that were previously not described there.
In addition to it always being a good policy to provide users with
the maximum possible amount of physical location information for
resources that can be hot-added and/or hot-removed, the following
are some (but likely not all) of the user benefits provided by
this change.
Immediate:
- Provides information needed to determine the specific node
on which a defective DIMM is located. This will reduce system
downtime when the node or defective DIMM is swapped out.
- Prevents unintended onlining of a memory section that was
previously offlined due to a defective DIMM. This could happen
during node hot-add when the user or node hot-add assist script
onlines _all_ offlined sections due to user or script inability
to identify the specific memory sections located on the hot-added
node. The consequences of reintroducing the defective memory
could be ugly.
- Provides information needed to vary the amount and distribution
of memory on specific nodes for testing or debugging purposes.
Future:
- Will provide information needed to identify the memory
sections that need to be offlined prior to physical removal
of a specific node.
Symlink creation during boot was tested on 2-node x86_64, 2-node
ppc64, and 2-node ia64 systems. Symlink creation during physical
memory hot-add tested on a 2-node x86_64 system.
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes the build errors and warnings in the binder driver. It can't
be a module, due to a lack of some of the symbols being exported.
Also added a MODULE_LICENSE(), as it was missing.
Cc: Arve Hjønnevåg <arve@android.com>
Cc: Brian Swetland <swetland@google.com>
Cc: Robert Love <rlove@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
From: San Mehat <san@android.com>
Cc: Brian Swetland <swetland@google.com>
Cc: Robert Love <rlove@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are files now in the drivers/staging/android/ directory, so the
dummy android.c file can be safely removed.
Cc: Robert Love <rlove@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
driver for GPIOs that turn back off after a delay
From: Mike Lockwood <lockwood@android.com>
Signed-off-by: Brian Swetland <swetland@google.com>
Cc: Robert Love <rlove@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Doesn't quite link properly under all configurations, and it has way too
many different build options, but it's a start.
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: Brian Swetland <swetland@google.com>
Cc: Robert Love <rlove@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Task credentials were moved and must be accessed through task_struct.cred
Signed-off-by: J.R. Mauro <jrm8005@gmail.com>
Cc: Arve Hjønnevåg <arve@android.com>
Cc: Brian Swetland <swetland@google.com>
Cc: Robert Love <rlove@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use the proper format specifiers for printing size_t values.
Signed-off-by: J.R. Mauro <jrm8005@gmail.com>
Cc: Arve Hjønnevåg <arve@android.com>
Cc: Brian Swetland <swetland@google.com>
Cc: Robert Love <rlove@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It builds, but not as a module, and with lots of warnings.
I also had to fix up a few syntax errors to get it to build
properly, I'm doubting that anyone has built it in a while :(
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: Brian Swetland <swetland@google.com>
Cc: Robert Love <rlove@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This prepares us to start adding the android drivers
to the build.
The dummy android.c file will go away in the next few patches, as it
will not be needed once drivers/staging/android/ has a driver in it.
Cc: Robert Love <rlove@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
netdev->priv is now gone, use netdev_priv() instead.
This fixes the build error in the network driver within the epl stack.
Cc: Daniel Krueger <daniel.krueger@systec-electronic.com>
Cc: Ronald Sieber <Ronald.Sieber@systec-electronic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Because of this, we can't set the mode for the timer, so delete this
code as it causes a build error right now.
Cc: Daniel Krueger <daniel.krueger@systec-electronic.com>
Cc: Ronald Sieber <Ronald.Sieber@systec-electronic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It's a start, still a mess...
Cc: Daniel Krueger <daniel.krueger@systec-electronic.com>
Cc: Ronald Sieber <Ronald.Sieber@systec-electronic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It's a start, still a mess...
Cc: Daniel Krueger <daniel.krueger@systec-electronic.com>
Cc: Ronald Sieber <Ronald.Sieber@systec-electronic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It's a start, still a mess...
Cc: Daniel Krueger <daniel.krueger@systec-electronic.com>
Cc: Ronald Sieber <Ronald.Sieber@systec-electronic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It's a start, still a mess...
Cc: Daniel Krueger <daniel.krueger@systec-electronic.com>
Cc: Ronald Sieber <Ronald.Sieber@systec-electronic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is the openPOWERLINK network stack from systec electronic.
It's a bit messed up as there is a driver mixed into the
middle of it, lots of work needs to be done to unwind the
different portions to make it sane.
Cc: Daniel Krueger <daniel.krueger@systec-electronic.com>
Cc: Ronald Sieber <Ronald.Sieber@systec-electronic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that netdev->priv is removed, fix the driver to use netdev->ml_priv
like it always should have been doing.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We are now using credentials, so just blindly setting the fsuid and
fsguid isn't acceptable. All this means is that the config file needs
to be readable by the driver thread, not a big deal.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is the Ralink RT2870 driver from the company that does horrible
things like reading a config file from /etc. However, the driver that
is currently under development from the wireless development community
is not working at all yet, so distros and users are using this version
instead (quite common hardware on a lot of netbook machines).
So here is this driver, for now, until the wireless developers get a
"clean" version into the main tree, or until this version is cleaned up
sufficiently to move out of the staging tree.
Ported to the Linux build system and cleaned up a bit already by me.
Cc: Linux wireless <linux-wireless@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the Mimio Xi interactive whiteboard driver to the tree.
It was originally written by mwilder@cs.nmsu.edu, but cleaned up and
forward ported by me to the latest kernel version.
Cc: Phil Hannent <phil@hannent.co.uk>
Cc: <mwilder@cs.nmsu.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds the driver for the Princeton Instruments USB camera.
Needs a lot of work...
TODO:
- make checkpatch.pl clean
- coding style fixups (typedefs, etc.)
- get it to build properly
- audit ioctls
- remove ioctls if possible
- assign proper minor number
- remove dbg() macro
- lots of general cleanups
- review locking
Cc: Judd Montgomery <judd@jpilot.org>
Cc: Jeff Frontz <jeff.frontz@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We only want to load for one PCI device, the "SE" device. The other PCI
devices that this driver supports are already supported by the existing
rtl8187 module.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a driver for the Realtek 8187 "SE" wireless PCI devices in some
netbook computers (MSI Wind, and others). It includes its own copy of
the ieee80211 stack, but it is compiled into the driver to prevend
duplicate symbol issues.
This version comes from Ralink with no authorship, but it is based
on an old version of the rtl8180 driver from Andrea Merello. It was
hacked up a bit to get it to build properly within the kernel tree and
to properly handle the merged wireless stack within the driver.
Cc: Andrea Merello <andreamrl@tiscali.it>
Cc: linux-wireless <linux-wireless@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Altera PCI Express Chaining DMA driver
A reference driver that exercises the Chaining DMA logic reference
design generated along the Altera FPGA PCI Express soft or hard core,
only if instantiated using the MegaWizard, not the SOPC builder, of
Quartus 8.1.
This driver can be used to test the logic instantiation and PCI
Express layers and acts as a starting point for driving custom logic
connected to the PCI Express End Point Chaining DMA engines.
Signed-off-by: Leon Woestenberg <leon@sidebranch.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Smartcard support was more like a proof-of-concept than a completed
work. It was only able to read serial numbers from a few smartcards,
and the goal was to be able to secure keypad access with a smartcard.
Given how the concept was limited, this was never used beyond demos,
and it's better to remove this code so that nobody tries to use it
for security purposes.
The function panel_bind_callback() was ifdef'ed out, as its only user
was smartcard. However, it would be a waste to remove it because many
variations made on this driver will need it.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Cc: Frank Menne <frank.menne@hsm.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The code began 8 years ago with kernel 2.0 or 2.1, and kernels 2.2 and
2.4 were still supported. These old version need no longer be supported
if the code gets merged in mainline.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Cc: Frank Menne <frank.menne@hsm.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
All of the 401 errors, and 108 of the 235 warnings reported by checkpatch
were cleared. The only remanining warnings left concern lines larger than
80 characters. This cleanup will be performed last.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Cc: Frank Menne <frank.menne@hsm.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds the lcd-panel parallel port driver to the staging tree.
See the file, drivers/staging/panel/TODO for what needs to be fixed up
in order for this to be properly merged into the rest of the kernel
tree.
Cc: Willy Tarreau <w@1wt.eu>
Cc: Frank Menne <frank.menne@hsm.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
next-20081120 kernel randconfig on x86_64 box fails, while !CONFIG_MODULES
drivers/staging/meilhaus/memain.c: In function 'me_probe_pci':
drivers/staging/meilhaus/memain.c:425: error: implicit declaration of function '__symbol_get'
drivers/staging/meilhaus/memain.c:425: warning: cast to pointer from integer of different size
drivers/staging/meilhaus/memain.c:433: warning: cast to pointer from integer of different size
drivers/staging/meilhaus/memain.c:453: error: implicit declaration of function '__symbol_put'
make[3]: *** [drivers/staging/meilhaus/memain.o] Error 1
the driver uses __symbol_get and __symbol_put instead of marco's
symbol_get and symbol_put, I have only build tested the patch.
Signed-off-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Originally written by Guenter Gebhardt <g.gebhardt@meilhaus.de>
and Krzysztof Gantzke <k.gantzke@meilhaus.de>
This is the drv/lnx/mod directory of ME-IDS 1.2.9 tarball with
some files from drv/lnx/include.
Signed-off-by: David Kiliani <mail@davidkiliani.de>
Cc: Guenter Gebhardt <g.gebhardt@meilhaus.de>
Cc: Krzysztof Gantzke <k.gantzke@meilhaus.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
asus_oled depends on the CONFIG_USB_SUPPORT, I have only build tested
the patch.
Signed-off-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Driver for the OLED tiny display on some Asus laptops.
From: Jakub Schmidtke <sjakub@gmail.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Don't include procfs functions if CONFIG_PROC_FS is not set
Signed-off by: J.R. Mauro <jrm8005@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
No more need for a kernel version check now that we are in the main
kernel tree.
Cc: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes the sparse issues that the tool had with the me_daq
driver.
Cc: Michael Hillmann <hillmann@syscongroup.de>
Cc: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This removes the typedefs from the me_daq driver.
Cc: Michael Hillmann <hillmann@syscongroup.de>
Cc: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a number of checkpatch.pl issues in the me_daq
driver.
Cc: Michael Hillmann <hillmann@syscongroup.de>
Cc: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds the me_daq comedi driver to the build.
From: Michael Hillmann <hillmann@syscongroup.de>
Cc: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds the rtd520 comedi driver to the build.
From: Dan Christian <dac@ptolemy.arc.nasa.gov>
Cc: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds the s626 comedi driver to the build.
From: Gianluca Palli <gpalli@deis.unibo.it>
Cc: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
comedi_pci_disable_no_regions is not called by any comedi code
(in or out of the kernel tree), so remove it, so no one tries to
use it in the future.
Cc: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
comedi_pci_enable_no_regions is not called by any comedi code
(in or out of the kernel tree), so remove it, so no one tries to
use it in the future.
Cc: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
just call pci_disable_device() directly in comedi_pci_enable()
as no wrapper is needed now that we are in the kernel tree.
Cc: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This resolves all the resolvable checkpatch.pl issues in the
comedi_pci.h file.
Cc: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This resolves all the resolvable checkpatch.pl issues in the
comedi_fc.h file.
Cc: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This resolves all the resolvable checkpatch.pl issues in the
comedi_parport.c file.
Cc: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
no more checkpatch.pl issues found in the comedi_test.c file.
Cc: Joachim Wuttke <Joachim.Wuttke@icn.siemens.de>
Cc: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes all issues pointed out by sparse with the comedi_test.c
file.
Cc: Joachim Wuttke <Joachim.Wuttke@icn.siemens.de>
Cc: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes almost all checkpatch.pl issues with the comedi_test.c
file.
Hint, volatile doesn't do what you think it does, it has been removed
from the structure...
Cc: Joachim Wuttke <Joachim.Wuttke@icn.siemens.de>
Cc: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes the issues raised by the sparse tool on the
comedi_bond.c file.
Cc: Calin A. Culianu <calin@ajvar.org>
Cc: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes the remaining checkpatch.pl issues found in the
comedi_bond.c file.
Cc: Calin A. Culianu <calin@ajvar.org>
Cc: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes all of the checkpatch.pl issues in the comedi_fc.c file.
Cc: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a number of the issues found by checkpatch.pl in the
comedi_bond.c file.
Cc: Calin A. Culianu <calin@ajvar.org>
Cc: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds the me4000 driver to the comedi staging tree
From: Guenter Gebhardt <g.gebhardt@meilhaus.com>
Cc: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds the icp_multi driver to the tree.
From: Anne Smorthit <anne.smorthit@sfwte.ch>
Cc: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The PCI wrapper macros are no longer needed, as they are
all for compatiblity with older kernel versions.
Cc: Anders Blomdell <anders.blomdell@control.lth.se>
Cc: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usb wrapper macros are no longer needed, as all of
the comedi drivers using them have been converted to
use the "native" USB core calls.
Cc: Anders Blomdell <anders.blomdell@control.lth.se>
Cc: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We don't need to set the owner field of the usb_driver structure
in the dt9812 driver.
Cc: Anders Blomdell <anders.blomdell@control.lth.se>
Cc: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove the comedi usb wrapper function usage in the usbduxfast driver as
they are no longer needed.
Cc: Bernd Porr <BerndPorr@f2s.com>
Cc: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove the comedi usb wrapper function usage in the usbdux driver as
they are no longer needed.
Cc: Bernd Porr <BerndPorr@f2s.com>
Cc: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove the typedef in the usbdux driver.
Cc: Bernd Porr <BerndPorr@f2s.com>
Cc: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix up and remove almost all of the remaining checkpatch.pl errors
and warnings in the usbdux driver.
Cc: Bernd Porr <BerndPorr@f2s.com>
Cc: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
printk() needs a KERN_ level. But it's usually better to just
use the dev_* functions instead, as they provide much better
information to the user and developer.
Cc: Bernd Porr <BerndPorr@f2s.com>
Cc: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This converts all // comments to be /* */
Cc: Bernd Porr <BerndPorr@f2s.com>
Cc: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix a lot of checkpatch.pl warnings and errors in the usbdux driver.
Cc: Bernd Porr <BerndPorr@f2s.com>
Cc: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that we are in the kernel tree, these ifdefs are not needed.
Cc: Bernd Porr <BerndPorr@f2s.com>
Cc: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
remove all warnings that sparse complains about in the dt9812 driver
Cc: Anders Blomdell <anders.blomdell@control.lth.se>
Cc: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
remove all typedefs from the dt9812 driver
Cc: Anders Blomdell <anders.blomdell@control.lth.se>
Cc: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
An extra .h file is not needed for the dt9812 driver so
merge it into the .c file.
Cc: Anders Blomdell <anders.blomdell@control.lth.se>
Cc: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Lots of checkpatch.pl warnings and errors resolved in the
comedi dt9812 usb driver.
Cc: Anders Blomdell <anders.blomdell@control.lth.se>
Cc: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds the comedi_parport driver to the kernel tree
From: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds the comedi_test driver to the kernel tree
From: Joachim Wuttke <Joachim.Wuttke@icn.siemens.de>
Cc: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds the comedi_bond driver to the kernel tree
From: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Data Translation DT9812 USB driver
From: Anders Blomdell <anders.blomdell@control.lth.se>
Cc: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
University of Stirling USB DAQ & INCITE Technology Limited driver.
From: Bernd Porr <BerndPorr@f2s.com>
Cc: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Hardware driver for NI Mite PCI interface chip
From: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This module is shared by many comedi drivers.
From: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This are used by usb and pci comedi drivers to handle the different
kernel versions. They will be eventually removed, but are needed now
to be able to add comedi drivers to the tree.
From: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed for some internal comedi driver macros that were
built up over the years to handle multiple kernel versions. It will be
removed eventually.
From: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds two "generic" Kconfig options, one for PCI and one for USB
comedi drivers, and the Makefile infrastructure as well. This is so
we can start adding individual comedi drivers and add them to the build
properly.
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: David Schleef <ds@schleef.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds the kcomedilib module
From: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If anyone included this file, it would break the build.
This patch fixes the issue.
Cc: David Schleef <ds@schleef.org>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are still some >80 character lines in there, but
this catches the majority of the issues.
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: David Schleef <ds@schleef.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Only clean up some of the easier ones in the .h files
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Cc: David Schleef <ds@schleef.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds the Comedi core to the staging tree.
This is a data acquision infrastructure for Linux, providing a common
interface for these types of drivers.
Taken directly from the comedi git tree, with only minor tweaks
by Greg to get it to build properly within the kernel tree.
From: David Schleef <ds@schleef.org>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Shawn Bohrer <shawn.bohrer@gmail.com>
Signed-off-by: Frank Mori Hess <fmhess@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch cleans up the way to check if there is enough space in the rx_q
while posting buffers.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
udelay() was not being defined properly, this patch fixes it.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Subbu Seetharaman <subbus@serverengines.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
So disable the driver in that build situation and document
that this needs to be fixed.
Cc: Subbu Seetharaman <subbus@serverengines.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
netdev->priv is now gone, so fix up all of the build errors in the benet
driver due to this change.
Cc: Subbu Seetharaman <subbus@serverengines.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The netif_rx_complete() and netif_rx_schedule() functions have changed,
so fix up the build breakage in the benet driver.
Cc: Subbu Seetharaman <subbus@serverengines.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed in order to get NetworkManager to work properly
with this driver.
More details can be found at
https://bugzilla.novell.com/show_bug.cgi?id=437959
Cc: Helmut Schaa <hschaa@novell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that netdev->priv is removed, fix the driver to use netdev->ml_priv
like it always should have been doing.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We are now using credentials, so just blindly setting the fsuid and
fsguid isn't acceptable. All this means is that the config file needs
to be readable by the driver thread, not a big deal.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is the Ralink RT2860 driver from the company that does horrible
things like reading a config file from /etc. However, the driver that
is currently under development from the wireless development community
is not working at all yet, so distros and users are using this version
instead (quite common hardware on a lot of netbook machines).
So here is this driver, for now, until the wireless developers get a
"clean" version into the main tree, or until this version is cleaned up
sufficiently to move out of the staging tree.
Ported to the Linux build system and cleaned up a bit already by me.
Cc: Linux wireless <linux-wireless@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Dependence on kernel version is not needed anymore
if we are in mainline now.
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Cc: <lrodriguez@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The #ifdef for version checking is wrong, and we no longer
pass the struct pt_regs to the urb callback functions. This
patch fixes this error.
Cc: Luis Rodriguez <Luis.Rodriguez@Atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make p80211wext_handler_def in the otus driver static. It's not used outside
this file and causes name clashes if it's visible.
Signed-off by: J.R. Mauro <jrm8005@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that netdev->priv is gone, fix things up properly in the otus driver
to use ml_priv as it should have always been doing.
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Initial dump of the otus USB wireless network driver.
It builds properly, but a lot of work needs to be done cleaning
it up before it can be merged into the wireless driver tree.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In commit e6a9854b05, the rate control API
was rewritten, so make the needed changes to the agnx driver so that it
will build and work properly.
Cc: Li YanBo <dreamfly281@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The wireless core has removed the ssid variables, so also remove
them from the agnx driver so that it builds properly.
Cc: Li YanBo <dreamfly281@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This should make the driver use request_firmware() instead of a static
firmware.
Some obvious things are missing:
1) The unneeded header files are not removed yet. This is to keep the
patch size small.
2) The .bin files are missing so the driver doesn't have what to load.
3) Testing. None of this was tested. It does compiles OK though :)
Signed-off-by: Lior Dotan <liodot@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix sizeof to use the right type
Signed-off-by: Lior Dotan <liodot@gmail.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
No argument named @regs in stub_complete(), remove it.
Signed-off-by: Qinghuang Feng <qhfeng.kernel@gmail.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The 'pPacket' variable is assigned, but never used. Remove it.
Signed-off-by: Johann Felix Soden <johfel@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
