They are a property of the SoC not the CPU itself.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Andreas Herrmann <andreas.herrmann@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7009/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some versions of the assembler will not assemble CFC1 for OCTEON, so
override the ISA for these.
Add r4k_fpu.o to handle low level FPU initialization.
Modify octeon_switch.S to save the FPU registers. And include
r4k_switch.S to pick up more FPU support.
Get rid of "#define cpu_has_fpu 0"
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Andreas Herrmann <andreas.herrmann@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7006/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch powers down the Malta in response to a power off command (eg.
poweroff or shutdown -P). It may then be powered back up by pressing the
"ON/NMI" button (S4) on the board. In cases where the power off state
cannot be entered (eg. because the required PCI support is disabled) the
current reset behaviour will be used as a fallback.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Tested-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6907/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When the system is halted it makes little sense to reset it. Instead,
hang by executing an infinite loop.
[ralf@linux-mips.org: Remove printk from mips_machine_halt() - this is not
the place to communicate with the user.]
Suggested-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6906/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch enables the PIIX4 to respond to special cycles on the PCI
bus. One such special cycle must be used in order to enter a suspend
state, and if response to it is not enabled then the suspend state will
never be entered.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6904/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch introduces code which will enter a suspend state via the
PIIX4. This can only be done when PCI support is enabled since it
requires access to PCI I/O space and the generation of a special cycle
on the PCI bus. In cases where PCI is disabled the mips_pm_suspend
function will simply always return an error.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6905/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch simply adds definitions for some I/O registers in the PIIX4
PM device, and the magic data for a special cycle which must occur on
the PCI bus in order for the PIIX4 to enter a suspend state.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6903/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On R4k DECstations the Halt button is wired to the NMI processor input
rather than an ordinary interrupt input such as on R3k DECstations. This
is possible with a different design of the CPU daughtercard that routes
the Halt button line from the baseboard connector. Additionally the
interrupt input has been reused for a different purpose on the KN04 and
KN05 R4k CPU daughtercards so it is better kept masked.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6705/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
R3k systems have no R4k timer so there's no point in pulling code that's
going to be dead.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6704/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This small update to the previous fix to __delay removes a conditional
around the ABI-dependent subtraction operation within an inline asm in
favor to the standard <asm/asm.h> LONG_SUBU macro. No change in code
produced.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6703/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Update to commit 9c9b415c50 [MIPS:
Reimplement get_cycles().]
On systems were for whatever reasons we can't use the cycle counter, fall
back to the c0_random register as an entropy source. It has however a
very small range that makes it suitable for random_get_entropy only and
not get_cycles.
This optimised version compiles to 8 instructions in the fast path even in
the worst case of all the conditions to check being variable (including a
MFC0 move delay slot that is only required for very old processors):
828: 8cf90000 lw t9,0(a3)
828: R_MIPS_LO16 jiffies
82c: 40057800 mfc0 a1,c0_prid
830: 3c0200ff lui v0,0xff
834: 00a21024 and v0,a1,v0
838: 1040007d beqz v0,a30 <add_interrupt_randomness+0x22c>
83c: 3c030000 lui v1,0x0
83c: R_MIPS_HI16 cpu_data
840: 40024800 mfc0 v0,c0_count
844: 00000000 nop
848: 00409021 move s2,v0
84c: 8ce20000 lw v0,0(a3)
84c: R_MIPS_LO16 jiffies
On most targets the sequence will be shorter and on some it will reduce to
a single `MFC0 <reg>,c0_count', as all MIPS architecture (i.e. non-legacy
MIPS) processors require the CP0 Count register to be present.
The only known exception that reports MIPS architecture compliance, but
contrary to that lacks CP0 Count is the Ingenic JZ4740 thingy. For broken
platforms like that this code requires cpu_has_counter to be hardcoded to
0 (i.e. no variable setting is permitted) so as not to penalise all the
other good platforms out there.
The asm barrier is required so that the compiler does not pull any
potentially costly (cold cache!) `cpu_data' variable access into the fast
path.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: John Crispin <blogic@openwrt.org>
Cc: Andrew McGregor <andrewmcgr@gmail.com>
Cc: Dave Taht <dave.taht@bufferbloat.net>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Simon Kelley <simon@thekelleys.org.uk>
Cc: Jim Gettys <jg@freedesktop.org>
Cc: David Daney <ddaney@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6702/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The XLP9XX SoC has an on-chip SATA controller with two ports. Add
ahci-init-xlp2.c to initialize the controller, setup the glue logic
registers, fixup PCI quirks and setup interrupt ack logic.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6913/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
XLP3XX includes an on-chip SATA controller with 4 ports. The
controller needs glue logic initialization and PCI fixup before
it can be used with the standard AHCI driver.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6872/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In XLP9XX, the interrupt routing table for MSI-X has been moved to the
PCIe controller's config space from PIC. There are also 32 MSI-X
interrupts available per link on XLP9XX.
Update XLP MSI/MSI-X code to handle this.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: g@linux-mips.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6912/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add support for the XLP5XX processor which is an 8 core variant of the
XLP9XX. Add XLP5XX cases to code which earlier handled XLP9XX.
Signed-off-by: Yonghong Song <ysong@broadcom.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6871/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Calculate XLP 9XX and 2XX core frequency from the per-core PLL. This
should give the correct value for all board configurations.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6870/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Update PIC frequency calculation for XLP9XX and 2XX processors using
the correct PLL registers. This should work for all possible board
configurations.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6876/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add the compatible property to the PIC entry. Also fix up the nodename
to use the correct address.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6869/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add IRQ to IRT (PIC interupt table index) mapping for SATA, GPIO, NAND
and SPI interfaces on the XLP SoC. Fix offsets for few blocks and add
device IDs for a few blocks.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6911/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The ELPA bit needs to be set in the PAGEGRAIN register to enable
access to >64GB physical address. Update reset.S to do this from
every hardware thread.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6866/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Update thread wakeup function to use scratch registers for saving SP and
RA. Move the register restore code needed for thread 0 to the calling
function. This reduces the size of code copied to the reset vector.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6910/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The macros in topology.h need CONFIG_SMP, and the uniprocessor compilation
fails due to this. Wrap the macros in an ifdef so that uniprocessor works.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6863/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This adds initial support for BPF-JIT on MIPS
Tested on mips32 LE/BE and mips64 BE/n64 using
dhcp, ping and various tcpdump filters.
Benchmarking:
Assuming the remote MIPS target uses 192.168.154.181
as its IP address, and the local host uses 192.168.154.136,
the following results can be obtained using the following
tcpdump filter (catches no frames) and a simple
'time ping -f -c 1000000' command.
[root@(none) ~]# tcpdump -p -n -s 0 -i eth0 net 10.0.0.0/24 -d
(000) ldh [12]
(001) jeq #0x800 jt 2 jf 8
(002) ld [26]
(003) and #0xffffff00
(004) jeq #0xa000000 jt 16 jf 5
(005) ld [30]
(006) and #0xffffff00
(007) jeq #0xa000000 jt 16 jf 17
(008) jeq #0x806 jt 10 jf 9
(009) jeq #0x8035 jt 10 jf 17
(010) ld [28]
(011) and #0xffffff00
(012) jeq #0xa000000 jt 16 jf 13
(013) ld [38]
(014) and #0xffffff00
(015) jeq #0xa000000 jt 16 jf 17
(016) ret #65535
- BPF-JIT Disabled
real 1m38.005s
user 0m1.510s
sys 0m6.710s
- BPF-JIT Enabled
real 1m35.215s
user 0m1.200s
sys 0m4.140s
[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
It will be used later on by bpf-jit
[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6736/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It will be used later on by bpf-jit
[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6733/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It will be used later on by bpf-jit
[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6732/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It will be used later on by bpf-jit
[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6731/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It will be used later on by bpf-jit
[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6730/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It will be used later on by bpf-jit
[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6729/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It will be used later on by bpf-jit
[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: http://patchwork.linux-mips.org/patch/6728/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It will be used later on by bpf-jit
[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6727/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It will be used later on by bpf-jit
[ralf@linux-mips.org: Fixed conflict due to other preceeding conflicts.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6726/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It will be used later on by bpf-jit
[ralf@linux-mips.org: Fixed conflict with
49e9529b9d [MIPS: uasm: add jalr instruction].
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6725/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Sometimes it's useful to let the user, while doing performance research,
know what in the IEEE754 exceptions has caused many times of FP emulation
when running a specific application. This patch adds 5 more files to
/sys/kernel/debug/mips/fpuemustats/, whose filenames begin with "ieee754".
These stats are in addition to the existing cp1ops, cp1xops, errors, loads
and stores, which may not be useful in understanding the reasons of ieee754
exceptions.
[ralf@linux-mips.org: Fixed reject due to other changes to the kernel
FP assist software.]
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Steven.Hill@imgtec.com
Cc: james.hogan@imgtec.com
Patchwork: http://patchwork.linux-mips.org/patch/7044/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patch was tested on devices with 64 MiB and 256 MiB of RAM.
It documents every part nicely and drops this hacky part of code:
max = off | ((128 << 20) - 1);
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/6808/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add interface mode detection for Octeon II. This is necessary to detect
the interface modes correctly on the UBNT E200 board. Code is taken
from the UBNT GPL source release, with some alterations: SRIO, ILK and
RXAUI interface modes are removed and instead return disabled as these
modes are not currently supported.
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Tested-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7039/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The CONFIG_MIPS_CPS SMP implementation should be able to handle all
cases the CONFIG_MIPS_CMP implementation does, but without requiring
bootloader assistance. It is also required in order to make use of
features such as hotplug & cpuidle core power gating. Enable it by
default for Malta configs that previously enabled the now deprecated
CONFIG_MIPS_CMP, and disable the latter. The local version suffix "cmp"
is removed rather than replaced with "cps" since there are other ways to
tell that the CPS SMP implementation is in use (the "VPE topology" line
in the boot log being one).
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
This patch adds a cpuidle driver for systems based around the MIPS
Coherent Processing System (CPS) architecture. It supports four idle
states:
- The standard MIPS wait instruction.
- The non-coherent wait, clock gated & power gated states exposed by
the recently added pm-cps layer.
The pm-cps layer is used to enter all the deep idle states. Since cores
in the clock or power gated states cannot service interrupts, the
gic_send_ipi_single function is modified to send a power up command for
the appropriate core to the CPC in cases where the target CPU has marked
itself potentially incoherent.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
This patch simply includes the cpuidle Kconfig entries in preparation
for cpuidle drivers used on MIPS systems.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Defines a macro intended to allow trivial use of the regular MIPS wait
instruction from cpuidle drivers, which may simply invoke the macro
within their array of states.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
