* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
Blackfin arch: use KBUILD_CFLAGS and KBUILD_AFLAGS in Makefile
Blackfin arch: Javier Herrer writes: fix building when icache and dcache is disabled
We must balance calls to get_task_mm with corresponding mmput calls, otherwise
refcounting is screwed up and mms don't get freed when their task exits.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Fix up /proc/cpuinfo so it is like everyone else, and gets
parsed by various applications properly. Still needs some tweaking on
parts without full L1 sram, like 532, 531, so it doesn't print out L1
bank info that doesn't exist.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Identical handlers of PTRACE_DETACH go into ptrace_request().
Not touching compat code.
Not touching archs that don't call ptrace_request.
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a problem reported in the forums - libstdc++ can call writev with an
iovec containing { NULL, 0 }, which works fine on i686-linux, but fails on
Blackfin. Fixed by allowing size 0 transfers to/from userspace regardless
of the address.
Signed-off-by: Bernd Schmidt <bernd.schmidt@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
- flush/inv the correct range
- dmacopy test failed when policy is write_back - invalidate before dma
http://blackfin.uclinux.org/gf/project/uclinux-dist/tracker/?action=TrackerItemEdit&tracker_item_id=3367
It's the cache invalidate what is causing the issue.
There is no invalidate only instruction it's always: FLUSHINV
So when we "invalidate" after the DMA we might (do) overwrite freshly
dma'ed data by dirty Cache WB content.
Fixed by moving the "invalidate" at the beginning of dma_memcpy.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Comply with revised Anomaly Workarounds for BF533 05000311 and BF561 05000323
accoring to BF533 anomaly sheet Rev. A 09/04/07
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Print out debug info, as early as possible - even before the
kernel initializes the interrupt vectors. Now we can print out debug
messages almost anytime during the boot process.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Also ensure that the traps_c code doesn't cause a double fault, by
sending a signal to a faulting kernel before the memory subsystem
is fully initialized, by printing out the error message before sending
the signal.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Today when a double fault happens (exception during an exception
handling event), we go into an endless loop, with nothing comming out
the UART. With this patch, we actually see that we have commited a
double fault event
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
This allows debugging of problems which happen eary in the kernel
boot process (after bootargs are parsed, but before serial subsystem
is fully initialized)
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
- Update gpio_request to allow multiple request with the same signature (label)
- Use generic GPIO API where applicable
- Update generic board support form stamp board
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
rewrite our reboot code in C rather than assembly to be like
other architectures and to allow board maintainers to define
custom behavior
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Break up our .init into separate section like all other ports do and
so that we dont mix text and data (causes disassembly headaches as
pointed out by Robin)
Cc: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
add an exception request/free api similar to the interrupt request/fre
api so people can utilize the free software based exceptions for their
own purposes
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
- allow people to select the feature that is unavailable to the kernel: NMI, JTAG, or CYCLES.
- change default NMI handler to simply dump hardware trace buffer.
- remove default NMI handler completely as calling into kernel code is not safe
move example handler to wiki so people dont haphazardly copy and paste this stuff thinking its safe
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
now all BLKFIN should be BFIN, should be no functional changes.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Add ability to expend the hardware trace buffer via a configurable
software buffer - so you can have lots of history when a crash occurs.
The interesting way we do printk in the traps.c confusese the checking
script
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
revise anomaly handling by basing things on the compiler not the kconfig defines,
so the header is stable and usable outside of the kernel. This also allows us to
move some code from preprocessing to compiling (gcc culls dead code)
which should help with code quality (readability, catch minor bugs, etc...).
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Initialize the exception vectors early in the boot process, so that CPLB faults
can be handled when memory protection is enabled.
Signed-off-by: Bernd Schmidt <bernd.schmidt@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
switch to using proper defines this time (THREAD_SIZE and PAGE_SIZE)
instead of just PAGE_SIZE everywhere
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bernd Schmidt <bernd.schmidt@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
