[why]
We have dynamic power control in driver but
should be ignored when power is forced on.
[how]
Bypass any power control when it's forced on.
Cc: stable@vger.kernel.org
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are a number of instances where we convert HostVMMinPageSize or
GPUVMMinPageSize from bytes to KB by dividing (rather than multiplying) and
vice versa.
Additionally, in some cases, a parameter is passed through DML in KB but
later checked as if it were in bytes.
Cc: stable@vger.kernel.org
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Taimur Hassan <syed.hassan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
KFD_GC_VERSION was recently updated to use a new function
for IP version checks. As a result, use KFD_GC_VERSION as
the common function for all IP version checks in KFD.
Signed-off-by: Mukul Joshi <mukul.joshi@amd.com>
Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Prevent overwrite of dc->config.use_default_clock_table, as it should be
pre-configured.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Taimur Hassan <syed.hassan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The new table doesn't have an implicit mapping between Fclk SOC voltage
and MemClk and it currently builds the table off of number of Fclk
states rather than DcfClock states.
The DML table in use is not correct for functionality or power and
does not align with our existing policies for DCN3x.
[How]
Build the table based on DcfClock with the following assumptions:
1. Raising Soc voltage is the most expensive operation, so assume that
running at max DispClock or DppClock is preferable.
2. Assume that we can run at max Fclk / MemClk at any state, but
restrict the maximum state to the very last entry in the table as the
worst case scenario.
3. Assume that Fclk always has a 2x multiplier on DcfClock unless the
table specifies something lower.
Reviewed-by: Taimur Hassan <syed.hassan@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Handover from DMUB to driver does not perform link rate toggle.
It might cause link training failure for boot up.
[HOW]
Force toggle rate wa for first link train.
link->vendor_specific_lttpr_link_rate_wa should be zero then.
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Michael Strauss <michael.strauss@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Zhongwei <zhongwei.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some panels with residency period of 2054 exhibit flickering with
Z8 at the end of the frame.
[How]
As a workaround, increase the limit to block these panels.
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Syed Hassan <syed.hassan@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Flickering occurs on DRR supported panels when engaged in DRR due to
min_dst_y_next becoming larger than the frame size itself.
[How]
In general, we should be able to enter Z8 when this is engaged but it
might be a net power loss even if the calculation wasn't bugged.
Don't support enabling Z8 during the DRR region.
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Syed Hassan <syed.hassan@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix a memory overflow issue in the gfx IB test
for some ASICs. At least 20 bytes are needed for
the IB test packet.
v2: correct code indentation errors. (Christian)
Signed-off-by: Tim Huang <Tim.Huang@amd.com>
Reviewed-by: Yifan Zhang <yifan1.zhang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
enable init_registers callback func for nbio v7.11.
Signed-off-by: Li Ma <li.ma@amd.com>
Reviewed-by: Yifan Zhang <yifan1.zhang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Remove the brightness cache in DC. It uses a single value to represent
the brightness for both SDR and HDR mode. This leads to flash in HDR
on/off. It also unconditionally programs brightness as in HDR mode. This
may introduce garbage on SDR mode in miniLED panel.
[How]
Simplify the initialization flow by removing the DC cache and taking
what panel has as default. Expand the mechanism for PWM to DPCD Aux to
restore cached brightness value generally.
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Krunoslav Kovac <krunoslav.kovac@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Camille Cho <camille.cho@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
If during driver init stage there are greater than 20
intermediary voltage states while constructing the SOC
BB we could hit issues because we will index outside of the
clock_limits array and start overwriting data. Increase the
total number of states to 40 to avoid this issue.
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Currently DCN35 does not spread DPREFCLK
[HOW]
Remove hardcoded table with nonzero caps
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
When choosing which dummy p-state latency to use, we
need to use the DRAM speed from validation. The DRAMSpeed
DML variable can change because we use different input
params to DML when populating watermarks set B.
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Wrong function is used to translate LUT values to HW format, leading to
visible artifacting in some cases.
[How]
Use the correct cm3_helper function.
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Krunoslav Kovac <krunoslav.kovac@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Ilya Bakoulin <ilya.bakoulin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We've updated the table but the values aren't being reflected in DML2
calculation.
[How]
Pass them into the bbox overrides.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Setting register to force ordering to prevent read/write or write/read
hazards for un-cached modes.
Signed-off-by: Alex Sierra <alex.sierra@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.1.x
In nbio v7_9, host driver should not issu gpu reset
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Stanley Yang <Stanley.Yang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We can override SR watermarks but not Z8 ones.
[How]
Add new parameters for Z8 matching the SR ones and feed them into the
states.
These also weren't being applied to every state, so make sure that
we loop over and update all SOC states if given an override.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The smu needs to get the rlc power down message to sync the rlc state
with smu, the rlc state updating message need to be sent at while smu
begin suspend sequence , otherwise SMU will crash while RLC state is not
notified by driver, and rlc state probally changed after that
notification, so it needs to notify rlc state to smu at the end of the
suspend sequence in amdgpu_device_suspend() that can make sure the rlc
state is correctly set to SMU.
[ 101.000590] amdgpu 0000:03:00.0: amdgpu: SMU: I'm not done with your previous command: SMN_C2PMSG_66:0x0000001E SMN_C2PMSG_82:0x00000000
[ 101.000598] amdgpu 0000:03:00.0: amdgpu: Failed to disable gfxoff!
[ 110.838026] amdgpu 0000:03:00.0: amdgpu: SMU: I'm not done with your previous command: SMN_C2PMSG_66:0x0000001E SMN_C2PMSG_82:0x00000000
[ 110.838035] amdgpu 0000:03:00.0: amdgpu: Failed to disable smu features.
[ 110.838039] amdgpu 0000:03:00.0: amdgpu: Fail to disable dpm features!
[ 110.838040] [drm:amdgpu_device_ip_suspend_phase2 [amdgpu]] *ERROR* suspend of IP block <smu> failed -62
[ 110.884394] PM: suspend of devices aborted after 21213.620 msecs
[ 110.884402] PM: start suspend of devices aborted after 21213.882 msecs
[ 110.884405] PM: Some devices failed to suspend, or early wake event detected
Reviewed-by: Yifan Zhang <yifan1.zhang@amd.com>
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
In dcn32 DML pipes are ordered the same as dc pipes but only for used
pipes. For example, if dc pipe 1 and 2 are used, their dml pipe indices
would be 0 and 1 respectively. However
update_pipe_slice_table_with_split_flags doesn't skip indices for free
pipes. This causes us to not reference correct dml pipe output when
building pipe topology.
[how]
Use two variables to iterate dc and dml pipes respectively and only
increment dml pipe index when current dc pipe is not free.
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Update to the new values per HW team request. Affects both stutter
and z8.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
GC IP 9.4.2 and up support TA reporting of the number
of xGMI links between peers.
Tested-by: Vignesh Chander <vignesh.chander@amd.com>
Signed-off-by: Jonathan Kim <jonathan.kim@amd.com>
Reviewed-by: Mukul Joshi <mukul.joshi@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DML2 means that the dcn3x policy for calculating z-state support
no longer runs from validate_bandwidth.
This means we are unconditionally allowing Z8, the hardware default.
[How]
Port the policy over to DCN35, but with a few modifications:
- Don't use min_dst_y_next_start as a check for Z8/Z10 allow
- Add support for overriding the Z10 stutter period per ASIC
- Cleanup the code to make the policy assignment more clear
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When waiting for the ACK for INBOX0 message,
we have to ensure to include the udelay
for proper wait time
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Commit 23baf831a3 ("mm, treewide: redefine MAX_ORDER sanely")
changed the meaning of MAX_ORDER from exclusive to inclusive. So, we
can allocate compound pages with up to 1 << MAX_ORDER pages.
Reflect this change in dm-flakey and start trying to allocate compound
pages with MAX_ORDER.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
dm_verity_fec_io is placed after the end of two hash digests. If the hash
digest has unaligned length, struct dm_verity_fec_io could be unaligned.
This commit fixes the placement of struct dm_verity_fec_io, so that it's
aligned.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Fixes: a739ff3f54 ("dm verity: add support for forward error correction")
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
We found an issue under Android OTA scenario that many BIOs have to do
FEC where the data under dm-verity is 100% complete and no corruption.
Android OTA has many dm-block layers, from upper to lower:
dm-verity
dm-snapshot
dm-origin & dm-cow
dm-linear
ufs
DM tables have to change 2 times during Android OTA merging process.
When doing table change, the dm-snapshot will be suspended for a while.
During this interval, many readahead IOs are submitted to dm_verity
from filesystem. Then the kverity works are busy doing FEC process
which cost too much time to finish dm-verity IO. This causes needless
delay which feels like system is hung.
After adding debugging it was found that each readahead IO needed
around 10s to finish when this situation occurred. This is due to IO
amplification:
dm-snapshot suspend
erofs_readahead // 300+ io is submitted
dm_submit_bio (dm_verity)
dm_submit_bio (dm_snapshot)
bio return EIO
bio got nothing, it's empty
verity_end_io
verity_verify_io
forloop range(0, io->n_blocks) // each io->nblocks ~= 20
verity_fec_decode
fec_decode_rsb
fec_read_bufs
forloop range(0, v->fec->rsn) // v->fec->rsn = 253
new_read
submit_bio (dm_snapshot)
end loop
end loop
dm-snapshot resume
Readahead BIOs get nothing while dm-snapshot is suspended, so all of
them will cause verity's FEC.
Each readahead BIO needs to verify ~20 (io->nblocks) blocks.
Each block needs to do FEC, and every block needs to do 253
(v->fec->rsn) reads.
So during the suspend interval(~200ms), 300 readahead BIOs trigger
~1518000 (300*20*253) IOs to dm-snapshot.
As readahead IO is not required by userspace, and to fix this issue,
it is best to pass readahead errors to upper layer to handle it.
Cc: stable@vger.kernel.org
Fixes: a739ff3f54 ("dm verity: add support for forward error correction")
Signed-off-by: Wu Bo <bo.wu@vivo.com>
Reviewed-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
It is nontrivial to derive the role of the two attribute groups in source
file block/blk-sysfs.c. Hence add a comment that explains their roles. See
also commit 6d85ebf95c ("blk-sysfs: add a new attr_group for blk_mq").
Cc: Christoph Hellwig <hch@lst.de>
Cc: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20231128194019.72762-1-bvanassche@acm.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
struct ynl_req_state carries reply-related info from generated code
into generic YNL code. While we don't need reply info to execute
a request without a reply, we still need to pass in the struct, because
it's also where we get the pointer to struct ynl_sock from. Passing NULL
results in crashes if kernel returns an error or an unexpected reply.
Fixes: dc0956c98f ("tools: ynl-gen: move the response reading logic into YNL")
Link: https://lore.kernel.org/r/20231126225858.2144136-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The default dump handler needs to clear ret before returning.
Otherwise if the last interface returns an inconsequential
error this error will propagate to user space.
This may confuse user space (ethtool CLI seems to ignore it,
but YNL doesn't). It will also terminate the dump early
for mutli-skb dump, because netlink core treats EOPNOTSUPP
as a real error.
Fixes: 728480f124 ("ethtool: default handlers for GET requests")
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20231126225806.2143528-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When amd_pstate is running, writing to scaling_min_freq and
scaling_max_freq has no effect. These values are only passed to the
policy level, but not to the platform level. This means that the
platform does not know about the frequency limits set by the user.
To fix this, update the min_perf and max_perf values at the platform
level whenever the user changes the scaling_min_freq and scaling_max_freq
values.
Fixes: ffa5096a7c ("cpufreq: amd-pstate: implement Pstate EPP support for the AMD processors")
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Wyes Karny <wyes.karny@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Fix a really interesting potential core bug in the list iterator
requireing the use of READ_ONCE() discovered when testing kernel
compiles with clang.
- Check devm_kcalloc() return value and an array bounds in the STM32
driver.
- Fix an exotic string truncation issue in the s32cc driver, found
by the kernel test robot (impressive!)
- Fix an undocumented struct member in the cy8c95x0 driver.
- Fix a symbol overlap with MIPS in the Lochnagar driver, MIPS
defines a global symbol "RST" which is a bit too generic and
collide with stuff. OK this one should be renamed too, we will
fix that as well.
- Fix erroneous branch taking in the Realtek driver.
- Fix the mail address in MAINTAINERS for the s32g2 driver.
-----BEGIN PGP SIGNATURE-----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=oW3z
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v6.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
- Fix a really interesting potential core bug in the list iterator
requireing the use of READ_ONCE() discovered when testing kernel
compiles with clang.
- Check devm_kcalloc() return value and an array bounds in the STM32
driver.
- Fix an exotic string truncation issue in the s32cc driver, found by
the kernel test robot (impressive!)
- Fix an undocumented struct member in the cy8c95x0 driver.
- Fix a symbol overlap with MIPS in the Lochnagar driver, MIPS defines
a global symbol "RST" which is a bit too generic and collide with
stuff. OK this one should be renamed too, we will fix that as well.
- Fix erroneous branch taking in the Realtek driver.
- Fix the mail address in MAINTAINERS for the s32g2 driver.
* tag 'pinctrl-v6.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
dt-bindings: pinctrl: s32g2: change a maintainer email address
pinctrl: realtek: Fix logical error when finding descriptor
pinctrl: lochnagar: Don't build on MIPS
pinctrl: avoid reload of p state in list iteration
pinctrl: cy8c95x0: Fix doc warning
pinctrl: s32cc: Avoid possible string truncation
pinctrl: stm32: fix array read out of bound
pinctrl: stm32: Add check for devm_kcalloc
Before running a guest, the host process (e.g., QEMU) FP/VEC registers
are saved if they were being used, similarly to when the kernel uses FP
registers. The guest values are then loaded into regs, and the host
process registers will be restored lazily when it uses FP/VEC.
KVM HV has a bug here: the host process registers do get saved, but the
user MSR bits remain enabled, which indicates the registers are valid
for the process. After they are clobbered by running the guest, this
valid indication causes the host process to take on the FP/VEC register
values of the guest.
Fixes: 34e119c96b ("KVM: PPC: Book3S HV P9: Reduce mtmsrd instructions required to save host SPRs")
Cc: stable@vger.kernel.org # v5.17+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20231122025811.2973-1-npiggin@gmail.com
We used to call intel_pre_plane_updates() for any pipe going through
a modeset whether the pipe was previously enabled or not. This in
fact needed to apply all the necessary clock gating workarounds/etc.
Restore the correct behaviour.
Fixes: 3991999732 ("drm/i915: Disable all planes before modesetting any pipes")
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231121054324.9988-3-ville.syrjala@linux.intel.com
(cherry picked from commit e0d5ce11ed)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Unfortunately even the HPD based detection added in
commit cfe5bdfb27 ("drm/i915: Check HPD live state during eDP probe")
fails to detect that the VBT's eDP/DDI-A is a ghost on
Asus B360M-A (CFL+CNP). On that board eDP/DDI-A has its HPD
asserted despite nothing being actually connected there :(
The straps/fuses also indicate that the eDP port is present.
So if one boots with a VGA monitor connected the eDP probe will
mistake the DP->VGA converter hooked to DDI-E for an eDP panel
on DDI-A.
As a last resort check what kind of DP device we've detected,
and if it looks like a DP->VGA converter then conclude that
the eDP port should be ignored.
Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/9636
Fixes: cfe5bdfb27 ("drm/i915: Check HPD live state during eDP probe")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231114142333.15799-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit fcd479a791)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The GSC CS is not exposed to the user, so we skipped assigning a uabi
class number for it. However, the trace logs use the uabi class and
instance to identify the engine, so leaving uabi class unset makes the
GSC CS show up as the RCS in those logs.
Given that the engine is not exposed to the user, we can't add a new
case in the uabi enum, so we insted internally define a kernel
internal class as -1.
At the same time remove special handling for the name and complete
the uabi_classes array so internal class is automatically correctly
assigned.
Engine will show as 65535:0 other0 in the logs/traces which should
be unique enough.
v2:
* Fix uabi class u8 vs u16 type confusion.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: 194babe26b ("drm/i915/mtl: don't expose GSC command streamer to the user")
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Alan Previn <alan.previn.teres.alexis@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231116084456.291533-1-tvrtko.ursulin@linux.intel.com
(cherry picked from commit dfed6b58d5)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This fixes a bug where going read-only was taking longer than it should
have due to copygc forgetting to check kthread_should_stop()
Additionally: fix a missing is_kthread check in bch2_move_ratelimit().
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
This eliminates some SRCU warnings: for_each_btree_key2() runs every
loop iteration in a distinct transaction context.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
btree writes update the btree node key after every write, in order to
update sectors_written, and they also might need to drop pointers if one
of the writes failed in a replicated btree node.
But the btree node might also have had a pointer dropped while the write
was in flight, by bch2_dev_metadata_drop(), and thus there was a bug
where the btree node write would ovewrite the btree node's key with what
it had at the start of the write.
Fix this by dropping pointers not currently in the btree node key.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
journal_cur_seq() can legitimately be used outside of the journal lock,
where this assert can race
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
The automated tests check if we've hit too many slowpath/error path
events and fail the test - if we're just shutting down, that naturally
shouldn't count.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Fix races between ravb_tx_timeout_work() and functions of net_device_ops
and ethtool_ops by using rtnl_trylock() and rtnl_unlock(). Note that
since ravb_close() is under the rtnl lock and calls cancel_work_sync(),
ravb_tx_timeout_work() should calls rtnl_trylock(). Otherwise, a deadlock
may happen in ravb_tx_timeout_work() like below:
CPU0 CPU1
ravb_tx_timeout()
schedule_work()
...
__dev_close_many()
// Under rtnl lock
ravb_close()
cancel_work_sync()
// Waiting
ravb_tx_timeout_work()
rtnl_lock()
// This is possible to cause a deadlock
If rtnl_trylock() fails, rescheduling the work with sleep for 1 msec.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20231127122420.3706751-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We can't rely on FILE_STANDARD_INFORMATION::EndOfFile for reparse
points as they will be always zero. Set it to symlink target's length
as specified by POSIX.
This will make stat() family of syscalls return the correct st_size
for such files.
Cc: stable@vger.kernel.org
Signed-off-by: Paulo Alcantara (SUSE) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
