The volume blocks have an step of 0.375dB, but TLV uses 0.01dB for
units. Only use the resolution supported, ignoring the LSB of the
volume register. This results in half the steps and 0.75dB per step,
but reports accurate levels through TLV. Update the masks to reflect
that these are registers have the LSB ignored.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
After the patch "ASoC: rt5677: Use specific r/w function for DSP mode", the
regmap_range "rt5677_ranges" was not registered in rt5677_regmap_physical, and
it caused that the regmap_range "rt5677_ranges" cannot be accessed by the
specific r/w function. The patch fixes this issue.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the slow charge of the vref in the end of the power sequences
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In DSP mode, the register r/w should use the specific function to access
that is invoked by address mapping of the DSP.
The MX-65[1] is for switching DSP or codec mode.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is for channel to slot mapping, and it is not only for 8 channels mapping,
but also in 2, 4 and 6 channels mapping. If we want to use the 2 channels in
the stereo2 adc path, we need to set the item "2/1/3/4" or "2/3/1/4".
It also adds for stereo channel swap. It can map the sterero channels "L/R"
to "R/L", "L/L" or R/R.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This allows to enable Mic Jack detection feature
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Modified-by: Anatol Pomozov <anatol.pomozov@gmail.com>
Signed-off-by: Anatol Pomozov <anatol.pomozov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ALC5677 has a programmable DSP, and there is a SPI that is dadicated for DSP
firmware loading. Therefore, the patch includes a SPI driver for writing the DSP
firmware. The VAD(Voice Activaty Detection) has be implemented and use the DSP to
recognize the key phase.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The header file is needed because struct gpio_chip is
placed in struct rt5677_priv.
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some boards have this pin statically tied and do not require any configuration,
some other boards allow to enable chip using GPIO.
Add an option that tells which GPIO is used to power the audio codec.
Signed-off-by: Anatol Pomozov <anatol.pomozov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add sidetone function
Signed-off-by: Anatol Pomozov <anatol.pomozov@gmail.com>
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are two pins can be used for rt5677's DMIC2 clock. This patch
add the select options for it.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The patch removes the redundant definition in head file
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The implementation of rt5677_pll_calc() has the same logic of rl6231_pll_calc().
The only difference is the lower boundary checking for freq_in.
This patch calls rl6231_pll_calc() instead of open-coded.
The k_bp of struct rt5677_pll_code is always false, thus also remove the
code to check pll_code.k_bp.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
