Even though the intent is to extend dmatest with P+Q tests there is
still value in having an always-on sanity check to prevent an
unintentionally broken driver from registering.
This depends on raid6_pq.ko for verification, the side effect being that
PQ capable channels will fail to register when raid6 is disabled.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
iop33x support is not included because that engine is a bit more awkward
to handle in that it can either be in xor mode or pq mode. The
dmaengine/async_tx layers currently only comprehend static capabilities.
Note iop13xx does not support hardware PQ continuation so the driver
must handle the DMA_PREP_CONTINUE flag for operations across > 16
sources. From the comment for dma_maxpq:
/* When an engine does not support native continuation we need 3 extra
* source slots to reuse P and Q with the following coefficients:
* 1/ {00} * P : remove P from Q', but use it as a source for P'
* 2/ {01} * Q : use Q to continue Q' calculation
* 3/ {00} * Q : subtract Q from P' to cancel (2)
*/
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
lockdep correctly identifies a potential recursive locking case for
iop_chan->lock, but in the dependency submission case we expect that the same
class will be acquired for both the parent dependency and the child channel.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Test raid6 p+q operations with a simple "always multiply by 1" q
calculation to fit into dmatest's current destination verification
scheme.
Reviewed-by: Andre Noll <maan@systemlinux.org>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
[ Based on an original patch by Yuri Tikhonov ]
This adds support for doing asynchronous GF multiplication by adding
two additional functions to the async_tx API:
async_gen_syndrome() does simultaneous XOR and Galois field
multiplication of sources.
async_syndrome_val() validates the given source buffers against known P
and Q values.
When a request is made to run async_pq against more than the hardware
maximum number of supported sources we need to reuse the previous
generated P and Q values as sources into the next operation. Care must
be taken to remove Q from P' and P from Q'. For example to perform a 5
source pq op with hardware that only supports 4 sources at a time the
following approach is taken:
p, q = PQ(src0, src1, src2, src3, COEF({01}, {02}, {04}, {08}))
p', q' = PQ(p, q, q, src4, COEF({00}, {01}, {00}, {10}))
p' = p + q + q + src4 = p + src4
q' = {00}*p + {01}*q + {00}*q + {10}*src4 = q + {10}*src4
Note: 4 is the minimum acceptable maxpq otherwise we punt to
synchronous-software path.
The DMA_PREP_CONTINUE flag indicates to the driver to reuse p and q as
sources (in the above manner) and fill the remaining slots up to maxpq
with the new sources/coefficients.
Note1: Some devices have native support for P+Q continuation and can skip
this extra work. Devices with this capability can advertise it with
dma_set_maxpq. It is up to each driver how to handle the
DMA_PREP_CONTINUE flag.
Note2: The api supports disabling the generation of P when generating Q,
this is ignored by the synchronous path but is implemented by some dma
devices to save unnecessary writes. In this case the continuation
algorithm is simplified to only reuse Q as a source.
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Reviewed-by: Andre Noll <maan@systemlinux.org>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
We currently walk the parent chain when waiting for a given tx to
complete however this walk may race with the driver cleanup routine.
The routines in async_raid6_recov.c may fall back to the synchronous
path at any point so we need to be prepared to call async_tx_quiesce()
(which calls dma_wait_for_async_tx). To remove the ->parent walk we
guarantee that every time a dependency is attached ->issue_pending() is
invoked, then we can simply poll the initial descriptor until
completion.
This also allows for a lighter weight 'issue pending' implementation as
there is no longer a requirement to iterate through all the channels'
->issue_pending() routines as long as operations have been submitted in
an ordered chain. async_tx_issue_pending() is added for this case.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
dmaengine: at_hdmac: add DMA slave transfers
dmaengine: at_hdmac: new driver for the Atmel AHB DMA Controller
dmaengine: dmatest: correct thread_count while using multiple thread per channel
dmaengine: dmatest: add a maximum number of test iterations
drivers/dma: Remove unnecessary semicolons
drivers/dma/fsldma.c: Remove unnecessary semicolons
dmaengine: move HIGHMEM64G restriction to ASYNC_TX_DMA
fsldma: do not clear bandwidth control bits on the 83xx controller
fsldma: enable external start for the 83xx controller
fsldma: use PCI Read Multiple command
When first created the ioat driver was the only inhabitant of
drivers/dma/. Now, it is the only multi-file (more than a .c and a .h)
driver in the directory. Moving it to an ioat/ subdirectory allows the
naming convention to be cleaned up, and allows for future splitting of
the source files by hardware version (v1, v2, and v3).
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch for at_hdmac adds the slave transfers capability to the Atmel DMA
controller available on some AT91 SOCs. This allow peripheral to memory and
memory to peripheral transfers with hardware handshaking.
Slave structure for controller specific information is passed through channel
private data. This at_dma_slave structure is defined in at_hdmac.h header file
and relative hardware definition are moved to this file from at_hdmac_regs.h.
Doing this we allow the channel configuration from platform definition code.
This work is intensively based on dw_dmac and several slave implementations.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This AHB DMA Controller (aka HDMA or DMAC on AT91 systems) is availlable on
at91sam9rl chip. It will be used on other products in the future.
This first release covers only the memory-to-memory tranfer type. This is the
only tranfer type supported by this chip. On other products, it will be used
also for peripheral DMA transfer (slave API support to come).
I used dmatest client without problem in different configurations to test it.
Full documentation for this controller can be found in the SAM9RL datasheet:
http://www.atmel.com/dyn/products/product_card.asp?part_id=4243
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
It seems that thread_count is not properly calculated in dmatest.
In fact the thread count number that is returned from dmatest_add_threads() is
not correctly added to the thread_count and thus not properly printed.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The dmatest usually waits for the killing of its kthreads to stop
running tests. This patch adds a parameter that sets a maximum
number of test iterations.
This feature is quite interesting for debugging when you set a lot of
traces in your dmaengine controller driver.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch reworks platform driver power management code
for txx9dmac from legacy late/early callbacks to dev_pm_ops.
The callbacks are converted for CONFIG_SUSPEND like this:
suspend_late() -> suspend_noirq()
resume_early() -> resume_noirq()
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch reworks platform driver power management code
for dw_dmac from legacy late/early callbacks to dev_pm_ops.
The callbacks are converted for CONFIG_SUSPEND like this:
suspend_late() -> suspend_noirq()
resume_early() -> resume_noirq()
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
On HIGHMEM64G systems dma_addr_t is known to be larger than (void *)
which precludes async_xor from performing dma address conversions by
reusing the input parameter address list. However, other parts of the
dmaengine infrastructure do not suffer this constraint, so the
HIGHMEM64G restriction can be down-levelled.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch does not change actual behaviour since dma_unmap_page is just
an alias of dma_unmap_single on MIPS.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds support for the integrated DMAC of the TXx9 family.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The 83xx controller does not support the external pause feature. The bit
in the mode register that controls external pause on the 85xx controller
happens to be part of the bandwidth control settings for the 83xx
controller.
This patch fixes the driver so that it only clears the external pause bit
if the hardware is the 85xx controller. When driving the 83xx controller,
the bit is left untouched. This follows the existing convention that mode
registers settings are not touched unless necessary.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The 83xx controller has external start capability, but lacks external pause
capability. Hook up the external start function pointer for the 83xx
controller.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
By default, the Freescale 83xx DMA controller uses the PCI Read Line
command when reading data over the PCI bus. Setting the controller to use
the PCI Read Multiple command instead allows the controller to read much
larger bursts of data, which provides a drastic speed increase.
The slowdown due to using PCI Read Line was only observed when a PCI-to-PCI
bridge was between the devices trying to communicate.
A simple test driver showed an increase from 4MB/sec to 116MB/sec when
performing DMA over the PCI bus. Using DMA to transfer between blocks of
local SDRAM showed no change in performance with this patch. The dmatest
driver was also used to verify the correctness of the transfers, and showed
no errors.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Acked-by: Timur Tabi <timur@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
async_xor() needs space to perform dma and page address conversions. In
most cases the code can simply reuse the struct page * array because the
size of the native pointer matches the size of a dma/page address. In
order to support archs where sizeof(dma_addr_t) is larger than
sizeof(struct page *), or to preserve the input parameters, we utilize a
memory region passed in by the caller.
Since the code is now prepared to handle the case where it cannot
perform address conversions on the stack, we no longer need the
!HIGHMEM64G dependency in drivers/dma/Kconfig.
[ Impact: don't clobber input buffers for address conversions ]
Reviewed-by: Andre Noll <maan@systemlinux.org>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Testing the i7300_idle driver on i5000-series hardware required
an edit to i7300_idle.h to "#define SUPPORT_I5000 1" and a re-build
of both i7300_idle and ioat_dma.
Replace that build-time scheme with a load-time module parameter:
"7300_idle.forceload=1" to make it easier to test the driver
on hardware that while not officially validated, works fine
and is much more commonly available.
By default (no modparam) the driver will continue to load
only on the i7300.
Note that ioat_dma runs a copy of i7300_idle's probe routine
to know to reserve an IOAT channel for i7300_idle.
This change makes ioat_dma do that always on the i5000,
just like it does on the i7300.
Signed-off-by: Len Brown <len.brown@intel.com>
Acked-by: Andrew Henroid <andrew.d.henroid@intel.com>
We we build with dma_addr_t as a 64-bit quantity we get:
drivers/dma/fsldma.c: In function 'fsl_chan_xfer_ld_queue':
drivers/dma/fsldma.c:625: warning: cast to pointer from integer of different size
drivers/dma/fsldma.c: In function 'fsl_dma_chan_do_interrupt':
drivers/dma/fsldma.c:737: warning: cast to pointer from integer of different size
drivers/dma/fsldma.c:737: warning: cast to pointer from integer of different size
drivers/dma/fsldma.c: In function 'of_fsl_dma_probe':
drivers/dma/fsldma.c:927: warning: cast to pointer from integer of different
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
When preparing a memcpy operation, if the kernel fails to allocate memory
for a link descriptor after the first link descriptor has already been
allocated, then some memory will never be released. Fix the problem by
walking the list of allocated descriptors backwards, and freeing the
allocated descriptors back into the DMA pool.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Li Yang <leoli@freescale.com>
On the 83xx controller, snooping is necessary for the DMA controller to
ensure cache coherence with the CPU when transferring to/from RAM.
The last descriptor in a chain will always have the End-of-Chain interrupt
bit set, so we can set the snoop bit while adding the End-of-Chain
interrupt bit.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Li Yang <leoli@freescale.com>
When creating a DMA transaction with multiple descriptors, the async_tx
cookie is set to 0 for each descriptor in the chain, excluding the last
descriptor, whose cookie is set to -EBUSY.
When fsl_dma_tx_submit() is run, it only assigns a cookie to the first
descriptor. All of the remaining descriptors keep their original value,
including the last descriptor, which is set to -EBUSY.
After the DMA completes, the driver will update the last completed cookie
to be -EBUSY, which is an error code instead of a valid cookie. This causes
dma_async_is_complete() to always return DMA_IN_PROGRESS.
This causes the fsldma driver to never cleanup the queue of link
descriptors, and the driver will re-run the DMA transaction on the hardware
each time it receives the End-of-Chain interrupt. This causes an infinite
loop.
With this patch, fsl_dma_tx_submit() is changed to assign a cookie to every
descriptor in the chain. The rest of the code then works without problems.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Li Yang <leoli@freescale.com>
When using the DMA controller from multiple threads at the same time, it is
possible to get lots of "DMA halt timeout!" errors printed to the kernel
log.
This occurs due to a race between fsl_dma_memcpy_issue_pending() and the
interrupt handler, fsl_dma_chan_do_interrupt(). Both call the
fsl_chan_xfer_ld_queue() function, which does not protect against
concurrent accesses to dma_halt() and dma_start().
The existing spinlock is moved to cover the dma_halt() and dma_start()
functions. Testing shows that the "DMA halt timeout!" errors disappear.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Li Yang <leoli@freescale.com>
Fix the check of potential array overflow when using corrupted channel
device tree nodes.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Li Yang <leoli@freescale.com>
This also fixes the case of a single queued buffer, for example, when taking a
single frame snapshot with the mx3_camera driver.
Reported-by: Agustin Ferrin Pozuelo <gatoguan-os@yahoo.com>
Tested-by: Agustin Ferrin Pozuelo <gatoguan-os@yahoo.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
as reported by Alexander Beregalov <a.beregalov@gmail.com>
ioatdma 0000:00:08.0: DMA-API: device driver frees DMA memory with
wrong function [device address=0x000000007f76f800] [size=2000 bytes]
[map
ped as single] [unmapped as page]
The ioatdma driver was unmapping all regions
(either allocated as page or single) using unmap_page.
This patch lets dma driver recognize if unmap_single or unmap_page should be used.
It introduces two new dma control flags:
DMA_COMPL_SRC_UNMAP_SINGLE and DMA_COMPL_DEST_UNMAP_SINGLE.
They should be set to indicate dma driver to do dma-unmapping as single
(first one for the source, tha latter for the destination).
If respective flag is not set, the driver assumes dma-unmapping as page.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Reported-by: Alexander Beregalov <a.beregalov@gmail.com>
Tested-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
disable_irq() should wait for all running handlers to complete
before returning. As such, if it's used to disable an interrupt
from that interrupt's handler it will deadlock. This replaces
the dangerous instances with the _nosync() variant which doesn't
have this problem.
Note the 2 handlers in question are only used #ifdef DEBUG so
I imagine these code paths don't get hit often.
Signed-off-by: Ben Nizette <bn@niasdigital.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The check for reaching max_channels is short circuited by 'continuing'
after successfully adding a channel.
[ Impact: make the 'max_channels' module parameter actually have an effect ]
Cc: <stable@kernel.org>
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
'zero_sum' does not properly describe the operation of generating parity
and checking that it validates against an existing buffer. Change the
name of the operation to 'val' (for 'validate'). This is in
anticipation of the p+q case where it is a requirement to identify the
target parity buffers separately from the source buffers, because the
target parity buffers will not have corresponding pq coefficients.
Reviewed-by: Andre Noll <maan@systemlinux.org>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
dma: Add SoF and EoF debugging to ipu_idmac.c, minor cleanup
dw_dmac: add cyclic API to DW DMA driver
dmaengine: Add privatecnt to revert DMA_PRIVATE property
dmatest: add dma interrupts and callbacks
dmatest: add xor test
dmaengine: allow dma support for async_tx to be toggled
async_tx: provide __async_inline for HAS_DMA=n archs
dmaengine: kill some unused headers
dmaengine: initialize tx_list in dma_async_tx_descriptor_init
dma: i.MX31 IPU DMA robustness improvements
dma: improve section assignment in i.MX31 IPU DMA driver
dma: ipu_idmac driver cosmetic clean-up
dmaengine: fail device registration if channel registration fails
Add Start-of-Frame and End-of-Frame debugging to ipu_idmac.c, in the
future it might also be needed for the actual video processing in
mx3-camera, at which point, the ISRs will have to be transferred to
mx3_camera.c, for which ipu_irq_map() and ipu_irq_unmap() functions will
have to be exported.
Also simplify a couple of pointer-dereferences.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch adds a cyclic DMA interface to the DW DMA driver. This is
very useful if you want to use the DMA controller in combination with a
sound device which uses cyclic buffers.
Using a DMA channel for cyclic DMA will disable the possibility to use
it as a normal DMA engine until the user calls the cyclic free function
on the DMA channel. Also a cyclic DMA list can not be prepared if the
channel is already active.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Currently dma_request_channel() set DMA_PRIVATE capability but never
clear it. So if a public channel was once grabbed by
dma_request_channel(), the device stay PRIVATE forever. Add
privatecnt member to dma_device to correctly revert it.
[lg@denx.de: fix bad usage of 'chan' in dma_async_device_register]
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Use the callback infrastructure to report driver/hardware hangs or
missed interrupts. Since this makes the test threads much more
aggressive (from: explicit 1ms sleep to: wait_for_completion) we set the
nice value to 10 so as to not swamp legitimate tasks.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Centralize this common initialization (and one case where ipu_idmac is
duplicating ->chan initialization).
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Add DMA error handling to the ISR, move common code fragments to functions, fix
scatter-gather element queuing in the ISR, survive channel freeing and
re-allocation in a quick succession.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The i.MX31 IPU DMA driver is a platform driver, but doesn't need hotplug, so we
can use __init and __exit function attributes.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Atsushi points out:
"If alloc_percpu or kzalloc failed, chan_id does not match with its
position in device->channels list.
And above "continue" looks buggy anyway. Keeping incomplete channels
in device->channels list looks very dangerous..."
Also, fix up leakage of idr_ref in the idr_pre_get() and channel init
fail cases.
Reported-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch adds clkdev support for i.MX31. This is done in a
similar way done previously for i.MX27
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
dmatest: fix use after free in dmatest_exit
ipu_idmac: fix spinlock type
iop-adma, mv_xor: fix mem leak on self-test setup failure
fsldma: fix off by one in dma_halt
I/OAT: fail self-test if callback test reaches timeout
I/OAT: update driver version and copyright dates
I/OAT: list usage cleanup
I/OAT: set tcp_dma_copybreak to 256k for I/OAT ver.3
I/OAT: cancel watchdog before dma remove
I/OAT: fail initialization on zero channels detection
I/OAT: do not set DCACTRL_CMPL_WRITE_ENABLE for I/OAT ver.3
I/OAT: add verification for proper APICID_TAG_MAP setting by BIOS
dmaengine: update kerneldoc
dmatest_cleanup_chanel will free dtc, so grab ->chan before it goes away
and use it to do the release.
Reported-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
fix a probably accidently dropped reference operator while calling
spin_unlock_restore to an ipu lock.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Cc: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
iop_adma_zero_sum_self_test has the brackets in the wrong place for the
setup failure deallocation path. This error was duplicated in
mv_xor_xor_self_test.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Prevent dev_err from firing even if we successfully detected 'dma-idle'
before the full 1ms timeout has elapsed.
Acked-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
If we miss interrupts in the self test then fail registration of this
channel as it is unsuitable for use as a public channel.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Together with new fixes update driver version
and extend copyright dates ranges.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Trivial cleanup, list_del(); list_add_tail() is equivalent
to list_move_tail(). Semantic patch for coccinelle can be
found at www.cccmz.de/~snakebyte/list_move_tail.spatch
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Upcoming server platforms from Intel based on the Nehalem performance
have significantly improved CPU based copy performance.
However, the DMA engine can still be effective at higher I/O sizes
for TCP traffic and at this time copybreak
should be set to 256k for TCP traffic only.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Channel watchdog should be canceled before the rest of dma remove stuff.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
On some systems with I/OAT ver.2 when DCA is disabled in BIOS
situations have been observed
that zero DMA channels are detected instead of four.
To avoid kernel panic driver should fail gracefully with appropriate message.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Flag DCACTRL_CMPL_WRITE_ENABLE is valid only for I/OAT ver.2
so it should not be set for I/OAT ver.3.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
BIOS versions for systems with I/OAT ver.2 have been found
which fail to program APICID_TAG_MAP for DCA.
The ioatdma driver should recognize incorrectly set APICID_TAG_MAP
and disable DCA in that case.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
`iop_adma_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`mv_xor_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`mv64xxx_i2c_unmap_regs' referenced in section `.devinit.text' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`mv64xxx_i2c_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`orion_nand_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`pxafb_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The conversion of atmel-mci to dma_request_channel missed the
initialization of the channel dma_slave information. The filter_fn passed
to dma_request_channel is responsible for initializing the channel's
private data. This implementation has the additional benefit of enabling
a generic client-channel data passing mechanism.
Reviewed-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
i.MX3x SoCs contain an Image Processing Unit, consisting of a Control
Module (CM), Display Interface (DI), Synchronous Display Controller (SDC),
Asynchronous Display Controller (ADC), Image Converter (IC), Post-Filter
(PF), Camera Sensor Interface (CSI), and an Image DMA Controller (IDMAC).
CM contains, among other blocks, an Interrupt Generator (IG) and a Clock
and Reset Control Unit (CRCU). This driver serves IDMAC and IG. They are
supported over dmaengine and irq-chip APIs respectively.
IDMAC is a specialised DMA controller, its DMA channels cannot be used for
general-purpose operations, even though it might be possible to configure
a memory-to-memory channel for memcpy operation. This driver will not work
with generic dmaengine clients, clients, wishing to use it must use
respective wrapper structures, they also must specify which channels they
require, as channels are hard-wired to specific IPU functions.
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
dma_find_channel and dma_issue_pending_all are good places to warn about
improper api usage. However, warning correctly means synchronizing with
dma_list_mutex, i.e. too much overhead for these fast-path calls.
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The mpc83xx variant uses a shared IRQ for all channels, so the individual
channel nodes don't have an interrupt property. Fix the code to print the
controller IRQ instead if there isn't any for the channel.
Acked-by: Timur Tabi <timur@freescale.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
There's no per-channel IRQ on mpc83xx, so only call free_irq if we have one.
Acked-by: Timur Tabi <timur@freescale.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The dmatest driver should use DMA_BIDIRECTIONAL on the destination buffer
to ensure that the poison values are written to RAM and not just written
to cache and discarded.
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The dmaengine sysfs implementation was fixed to support proper
lifetime rules which means that the current:
new_fsl_chan->dev = &new_fsl_chan->common.dev->device;
...retrieves a NULL pointer because new_fsl_chan->common.dev has not
been allocated at this point. So, set new_fsl_chan->dev to a valid
device.
Cc: Li Yang <leoli@freescale.com>
Cc: Zhang Wei <zw@zh-kernel.org>
Reported-by: Ira Snyder <iws@ovro.caltech.edu>
Tested-by: Ira Snyder <iws@ovro.caltech.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In dmaengine we track the dependencies between the descriptors
using the 'next' pointers of the structure. These pointers are
set to NULL as soon as the corresponding descriptor has been
submitted to the channel (in dma_run_dependencies()).
But, the first 'next' in chain is still remaining set, regardless
the fact, that tx->next has been already submitted. This may lead to
multiple submissions of the same descriptor. This patch fixes this.
Actually, some previous implementation of the xxx_run_dependencies()
function already had this fix in place. The fdb..0eaf3 commit, beside the
correct things, broke this.
Cc: <stable@kernel.org>
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In the multiple device case we need to re-arm the completion and protect
against concurrent self-tests. The printk from the test callback is
removed as it can arbitrarily delay completion of the test.
Cc: <stable@kernel.org>
Cc: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
There are dmaengine users that would like to register dma devices at
subsys_initcall time to ensure channels are available by device_initcall
time.
Cc: Maciej Sosnowski <maciej.sosnowski@intel.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Allow dma_filter_fn routines to disambiguate multiple channels on a device
rather than assuming that all channels on a device are equal.
Cc: Maciej Sosnowski <maciej.sosnowski@intel.com>
Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This brings some predictability to dma device numbers, i.e. an rmmod/insmod
cycle may now result in /sys/class/dma/dma0chan0 being restored rather than
/sys/class/dma/dma1chan0 appearing.
Cc: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Resolves:
WARNING: at drivers/base/core.c:122 device_release+0x4d/0x52()
Device 'dma0chan0' does not have a release() function, it is broken and must be fixed.
The dma_chan_dev object is introduced to gear-match sysfs kobject and
dmaengine channel lifetimes. When a channel is removed access to the
sysfs entries return -ENODEV until the kobject can be released.
The bulk of the change is updates to existing code to handle the extra
layer of indirection between a dma_chan and its struct device.
Reported-by: Alexander Beregalov <a.beregalov@gmail.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Unregistering services should only happen at "remove" time. This prevents
the device from being unregistered while dmaengine clients are still
active. Also, the comment on ioat_remove is stale since removal is prevented
while a channel may be in use.
Reported-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This BUG_ON caught problems in early development but now it is in the
way as it invalidly triggers when trying to remove the module.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
DMA_NAK is now useless. We can just use a bool instead.
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reference counting is done at the module level so clients need not worry
that a channel will leave while they are actively using dmaengine.
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
All users have been converted to either the general-purpose allocator,
dma_find_channel, or dma_request_channel.
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Now that clients no longer need to be notified of channel arrival
dma_async_client_register can simply increment the dmaengine_ref_count.
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
dma_request_channel provides an exclusive channel, so we no longer need to
pass slave data through dmaengine.
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Replace the client registration infrastructure with a custom loop to
poll for channels. Once dma_request_channel returns NULL stop asking
for channels. A userspace side effect of this change if that loading
the dmatest module before loading a dma driver will result in no
channels being found, previously dmatest would get a callback. To
facilitate testing in the built-in case dmatest_init is marked as a
late_initcall. Another side effect is that channels under test can not
be used for any other purpose.
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This interface is primarily for device-to-memory clients which need to
search for dma channels with platform-specific characteristics. The
prototype is:
struct dma_chan *dma_request_channel(dma_cap_mask_t mask,
dma_filter_fn filter_fn,
void *filter_param);
When the optional 'filter_fn' parameter is set to NULL
dma_request_channel simply returns the first channel that satisfies the
capability mask. Otherwise, when the mask parameter is insufficient for
specifying the necessary channel, the filter_fn routine can be used to
disposition the available channels in the system. The filter_fn routine
is called once for each free channel in the system. Upon seeing a
suitable channel filter_fn returns DMA_ACK which flags that channel to
be the return value from dma_request_channel. A channel allocated via
this interface is exclusive to the caller, until dma_release_channel()
is called.
To ensure that all channels are not consumed by the general-purpose
allocator the DMA_PRIVATE capability is provided to exclude a dma_device
from general-purpose (memory-to-memory) consideration.
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
async_tx and net_dma each have open-coded versions of issue_pending_all,
so provide a common routine in dmaengine.
The implementation needs to walk the global device list, so implement
rcu to allow dma_issue_pending_all to run lockless. Clients protect
themselves from channel removal events by holding a dmaengine reference.
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Allowing multiple clients to each define their own channel allocation
scheme quickly leads to a pathological situation. For memory-to-memory
offload all clients can share a central allocator.
This simply moves the existing async_tx allocator to dmaengine with
minimal fixups:
* async_tx.c:get_chan_ref_by_cap --> dmaengine.c:nth_chan
* async_tx.c:async_tx_rebalance --> dmaengine.c:dma_channel_rebalance
* split out common code from async_tx.c:__async_tx_find_channel -->
dma_find_channel
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Simply, if a client wants any dmaengine channel then prevent all dmaengine
modules from being removed. Once the clients are done re-enable module
removal.
Why?, beyond reducing complication:
1/ Tracking reference counts per-transaction in an efficient manner, as
is currently done, requires a complicated scheme to avoid cache-line
bouncing effects.
2/ Per-transaction ref-counting gives the false impression that a
dma-driver can be gracefully removed ahead of its user (net, md, or
dma-slave)
3/ None of the in-tree dma-drivers talk to hot pluggable hardware, but
if such an engine were built one day we still would not need to notify
clients of remove events. The driver can simply return NULL to a
->prep() request, something that is much easier for a client to handle.
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
async_tx.ko is a consumer of dma channels. A circular dependency arises
if modules in drivers/dma rely on common code in async_tx.ko. It
prevents either module from being unloaded.
Move dma_wait_for_async_tx and async_tx_run_dependencies to dmaeninge.o
where they should have been from the beginning.
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Mapping the destination multiple times is a misuse of the dma-api.
Since the destination may be reused as a source, ensure that it is only
mapped once and that it is mapped bidirectionally. This appears to add
ugliness on the unmap side in that it always reads back the destination
address from the descriptor, but gcc can determine that dma_unmap is a
nop and not emit the code that calculates its arguments.
Cc: <stable@kernel.org>
Cc: Saeed Bishara <saeed@marvell.com>
Acked-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
There is a possibility to have two devices registered with the same id.
Cc: <stable@kernel.org>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
As part of the ioat_dma self-test it performs a printk from a completion
callback. Depending on the system console configuration this output can
take longer than a millisecond causing the self-test to fail. Introduce a
completion with a generous timeout to mitigate this failure.
Cc: <stable@kernel.org>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Now that the critical read back to flush the next descriptor address is
fixed we can downgrade some BUG_ONs that need only be enabled when testing
changes to the driver.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The current dummy read references the wrong address allowing the next
descriptor address update to linger in the store buffer and get passed
by an 'append' event.
This issue was uncovered by the change from strongly-ordered to device
memory for the adma registers.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
async_tx.callback should be checked for the first
not the last descriptor in the chain.
Cc: <stable@kernel.org>
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Error handling needs to be modified in dma_pin_iovec_pages().
It should return NULL instead of ERR_PTR
(pinned_list is checked for NULL in tcp_recvmsg() to determine
if iovec pages have been successfully pinned down).
In case of error for the first iovec,
local_list->nr_iovecs needs to be initialized.
Cc: <stable@kernel.org>
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the ioatdma driver is loaded but not used it does not allocate descriptors.
Before it frees channel resources it should first be sure
that they have been previously allocated.
Cc: <stable@kernel.org>
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Tested-by: Tom Picard <tom.s.picard@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I7300_idle driver is not configured, there is a compile time
warning about IDLE_IOAT_CHANNEL not defined. Fix it.
Reported-by: Suresh Siddha <suresh.b.siddha@intel.com>
Reported-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Based on input from Andi Kleen:
share the platform detection code with ioat_dma and disable the channel in
dma engine only for specific platforms.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The Intel 7300 Memory Controller supports dynamic throttling of memory which can
be used to save power when system is idle. This driver does the memory
throttling when all CPUs are idle on such a system.
Refer to "Intel 7300 Memory Controller Hub (MCH)" datasheet
for the config space description.
Signed-off-by: Andy Henroid <andrew.d.henroid@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
fsldma: allow Freescale Elo DMA driver to be compiled as a module
fsldma: remove internal self-test from Freescale Elo DMA driver
drivers/dma/dmatest.c: switch a GFP_ATOMIC to GFP_KERNEL
dmatest: properly handle duplicate DMA channels
drivers/dma/ioat_dma.c: drop code after return
async_tx: make async_tx_run_dependencies() easier to read
The tasklet checks RAW.BLOCK twice, and does not check RAW.XFER. This is
obviously wrong, and could theoretically cause the driver to hang.
Reported-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Modify the Freescale Elo / Elo Plus DMA driver so that it can be compiled as
a module.
The primary change is to stop treating the DMA controller as a bus, and the
DMA channels as devices on the bus. This is because the Open Firmware (OF)
kernel code does not allow busses to be removed, so although we can call
of_platform_bus_probe() to probe the DMA channels, there is no
of_platform_bus_remove(). Instead, the DMA channels are manually probed,
similar to what fsl_elbc_nand.c does.
Cc: Scott Wood <scottwood@freescale.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The Freescale Elo DMA driver runs an internal self-test before registering
the channels with the DMA engine. This self-test has a fundemental flaw in
that it calls the DMA engine's callback functions directly before the
registration. However, the registration initializes some variables that the
callback functions uses, namely the device struct.
The code works today because there are two device structs: the one created
by the DMA engine, and one created by the Open Firmware (OF) subsystem. The
self-test currently uses the device struct created by OF. However, in the
future, some of the device structs created by OF will be eliminated.
This means that the self-test will only have access to the device struct
created by the DMA engine. But this device struct isn't initialized when
the self-test runs, and this causes a kernel panic.
Since there is already a DMA test module (dmatest), the internal self-test
code is not useful anyway. It is extremely unlikely that the test will fail
in normal usage. It may have been helpful during development, but not any more.
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
It was needlessly using the unreliable GFP_ATOMIC.
Cc: Timur Tabi <timur@freescale.com>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Update the the dmatest driver so that it handles duplicate DMA channels
properly.
When a DMA client is notified of an available DMA channel, it must check if it
has already allocated resources for that channel. If so, it should return
DMA_DUP. This can happen, for example, if a DMA driver calls
dma_async_device_register() more than once.
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The break after the return serves no purpose.
Signed-off-by: Julia Lawall <julia@diku.dk>
Reviewed-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch performs the equivalent include directory shuffle for
plat-orion, and fixes up all users.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
* 'for-linus-merged' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 5177/1: arm/mach-sa1100/Makefile: remove CONFIG_SA1100_USB
[ARM] 5166/1: magician: add MAINTAINERS entry
[ARM] fix pnx4008 build errors
[ARM] Fix SMP booting with non-zero PHYS_OFFSET
[ARM] 5185/1: Fix spi num_chipselect for lubbock
[ARM] Move include/asm-arm/arch-* to arch/arm/*/include/mach
[ARM] Add support for arch/arm/mach-*/include and arch/arm/plat-*/include
[ARM] Remove asm/hardware.h, use asm/arch/hardware.h instead
[ARM] Eliminate useless includes of asm/mach-types.h
[ARM] Fix circular include dependency with IRQ headers
avr32: Use <mach/foo.h> instead of <asm/arch/foo.h>
avr32: Introduce arch/avr32/mach-*/include/mach
avr32: Move include/asm-avr32 to arch/avr32/include/asm
[ARM] sa1100_wdt: use reset_status to remember watchdog reset status
[ARM] pxa: introduce reset_status and clear_reset_status for driver's usage
[ARM] pxa: introduce reset.h for reset specific header information
If you are using linked lists for queues list_splice() will not do what
you would expect even if you use the elements passed reversed. We need
to handle these differently. We add list_splice_tail() and
list_splice_tail_init().
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds to ioatdma and dca modules
support for Intel I/OAT DMA engine ver.3 (aka CB3 device).
The main features of I/OAT ver.3 are:
* 8 single channel DMA devices (8 channels total)
* 8 DCA providers, each can accept 2 requesters
* 8-bit TAG values and 32-bit extended APIC IDs
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
I/OAT DMA performance tuning showed different optimal values of
tcp_dma_copybreak for different I/OAT versions (4096 for 1.2 and 2048
for 2.0). This patch lets ioatdma driver set tcp_dma_copybreak value
according to these results.
[dan.j.williams@intel.com: remove some ifdefs]
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Due to occasional DMA channel hangs observed for I/OAT versions 1.2 and 2.0
a watchdog has been introduced to check every 2 seconds
if all channels progress normally.
If stuck channel is detected, driver resets it.
The reset is done in two parts. The second part is scheduled
by the first one to reinitialize the channel after the restart.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Force callers that trigger an "out of descriptors" condition to run the
cleanup loop directly. Alleviates the requirement to have soft-irqs
enabled when polling for a descriptor in async_xor.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This adds a driver for the Synopsys DesignWare DMA controller (aka
DMACA on AVR32 systems.) This DMA controller can be found integrated
on the AT32AP7000 chip and is primarily meant for peripheral DMA
transfer, but can also be used for memory-to-memory transfers.
This patch is based on a driver from David Brownell which was based on
an older version of the DMA Engine framework. It also implements the
proposed extensions to the DMA Engine API for slave DMA operations.
The dmatest client shows no problems, but there may still be room for
improvement performance-wise. DMA slave transfer performance is
definitely "good enough"; reading 100 MiB from an SD card running at ~20
MHz yields ~7.2 MiB/s average transfer rate.
Full documentation for this controller can be found in the Synopsys
DW AHB DMAC Databook:
http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf
The controller has lots of implementation options, so it's usually a
good idea to check the data sheet of the chip it's intergrated on as
well. The AT32AP7000 data sheet can be found here:
http://www.atmel.com/dyn/products/datasheets.asp?family_id=682
Changes since v4:
* Use client_count instead of dma_chan_is_in_use()
* Add missing include
* Unmap buffers unless client told us not to
Changes since v3:
* Update to latest DMA engine and DMA slave APIs
* Embed the hw descriptor into the sw descriptor
* Clean up and update MODULE_DESCRIPTION, copyright date, etc.
Changes since v2:
* Dequeue all pending transfers in terminate_all()
* Rename dw_dmac.h -> dw_dmac_regs.h
* Define and use controller-specific dma_slave data
* Fix up a few outdated comments
* Define hardware registers as structs (doesn't generate better
code, unfortunately, but it looks nicer.)
* Get number of channels from platform_data instead of hardcoding it
based on CONFIG_WHATEVER_CPU.
* Give slave clients exclusive access to the channel
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>,
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch adds the necessary interfaces to the DMA Engine framework
to use functionality found on most embedded DMA controllers: DMA from
and to I/O registers with hardware handshaking.
In this context, hardware hanshaking means that the peripheral that
owns the I/O registers in question is able to tell the DMA controller
when more data is available for reading, or when there is room for
more data to be written. This usually happens internally on the chip,
but these signals may also be exported outside the chip for things
like IDE DMA, etc.
A new struct dma_slave is introduced. This contains information that
the DMA engine driver needs to set up slave transfers to and from a
slave device. Most engines supporting DMA slave transfers will want to
extend this structure with controller-specific parameters. This
additional information is usually passed from the platform/board code
through the client driver.
A "slave" pointer is added to the dma_client struct. This must point
to a valid dma_slave structure iff the DMA_SLAVE capability is
requested. The DMA engine driver may use this information in its
device_alloc_chan_resources hook to configure the DMA controller for
slave transfers from and to the given slave device.
A new operation for preparing slave DMA transfers is added to struct
dma_device. This takes a scatterlist and returns a single descriptor
representing the whole transfer.
Another new operation for terminating all pending transfers is added as
well. The latter is needed because there may be errors outside the scope
of the DMA Engine framework that may require DMA operations to be
terminated prematurely.
DMA Engine drivers may extend the dma_device, dma_chan and/or
dma_slave_descriptor structures to allow controller-specific
operations. The client driver can detect such extensions by looking at
the DMA Engine's struct device, or it can request a specific DMA
Engine device by setting the dma_dev field in struct dma_slave.
dmaslave interface changes since v4:
* Fix checkpatch errors
* Fix changelog (there are no slave descriptors anymore)
dmaslave interface changes since v3:
* Use dma_data_direction instead of a new enum
* Submit slave transfers as scatterlists
* Remove the DMA slave descriptor struct
dmaslave interface changes since v2:
* Add a dma_dev field to struct dma_slave. If set, the client can
only be bound to the DMA controller that corresponds to this
device. This allows controller-specific extensions of the
dma_slave structure; if the device matches, the controller may
safely assume its extensions are present.
* Move reg_width into struct dma_slave as there are currently no
users that need to be able to set the width on a per-transfer
basis.
dmaslave interface changes since v1:
* Drop the set_direction and set_width descriptor hooks. Pass the
direction and width to the prep function instead.
* Declare a dma_slave struct with fixed information about a slave,
i.e. register addresses, handshake interfaces and such.
* Add pointer to a dma_slave struct to dma_client. Can be NULL if
the DMA_SLAVE capability isn't requested.
* Drop the set_slave device hook since the alloc_chan_resources hook
now has enough information to set up the channel for slave
transfers.
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In some cases client code may need the dma-driver to skip the unmap of source
and/or destination buffers. Setting these flags indicates to the driver to
skip the unmap step. In this regard async_xor is currently broken in that it
allows the destination buffer to be unmapped while an operation is still in
progress, i.e. when the number of sources exceeds the hardware channel's
maximum (fixed in a subsequent patch).
Acked-by: Saeed Bishara <saeed@marvell.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
A DMA controller capable of doing slave transfers may need to know a
few things about the slave when preparing the channel. We don't want
to add this information to struct dma_channel since the channel hasn't
yet been bound to a client at this point.
Instead, pass a reference to the client requesting the channel to the
driver's device_alloc_chan_resources hook so that it can pick the
necessary information from the dma_client struct by itself.
[dan.j.williams@intel.com: fixed up fsldma and mv_xor]
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This client tests DMA memcpy using various lengths and various offsets
into the source and destination buffers. It will initialize both
buffers with a repeatable pattern and verify that the DMA engine copies
the requested region and nothing more. It will also verify that the
bytes aren't swapped around, and that the source buffer isn't modified.
The dmatest module can be configured to test a specific device, a
specific channel. It can also test multiple channels at the same time,
and it can start multiple threads competing for the same channel.
Changes since v2:
* Support testing multiple channels at the same time
* Support testing with multiple threads competing for the same channel
* Use counting test patterns in order to catch byte ordering issues
Changes since v1:
* Remove extra dashes around "help"
* Remove "default n" from Kconfig
* Turn TEST_BUF_SIZE into a module parameter
* Return DMA_NAK instead of DMA_DUP
* Print unhandled events
* Support testing specific channels and devices
* Move to the end of the Makefile
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The XOR engine found in Marvell's SoCs and system controllers
provides XOR and DMA operation, iSCSI CRC32C calculation, memory
initialization, and memory ECC error cleanup operation support.
This driver implements the DMA engine API and supports the following
capabilities:
- memcpy
- xor
- memset
The XOR engine can be used by DMA engine clients implemented in the
kernel, one of those clients is the RAID module. In that case, I
observed 20% improvement in the raid5 write throughput, and 40%
decrease in the CPU utilization when doing array construction, those
results obtained on an 5182 running at 500Mhz.
When enabling the NET DMA client, the performance decreased, so
meanwhile it is recommended to keep this client off.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Since 43cc71eed1, the platform
modalias is prefixed with "platform:". Add MODULE_ALIAS() to most
of the hotpluggable platform drivers, to re-enable auto loading.
Cc: <stable@kernel.org>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Haavard's dma-slave interface would like to test for exclusive access to a
channel. The standard channel refcounting is not sufficient in that it
tracks more than just client references, it is also inaccurate as reference
counts are percpu until the channel is removed.
This change also enables a future fix to deallocate resources when a client
declines to use a capable channel.
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The dependency is redundant since all drivers set their specific arch
dependencies. The NET_DMA option is modified to be enabled only on platforms
where it is known to have a positive effect. HAS_DMA is added as an explicit
dependency for the DMADEVICES menu.
Acked-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Set the 'parent' field of channel class devices to point to the
physical DMA device initialized by the DMA engine driver.
This allows drivers to use chan->dev.parent for syncing DMA buffers
and adds a 'device' symlink to the real device in
/sys/class/dma/dmaXchanY.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
1) Remove an explicit memset(.., 0, ...) to a variable allocated with
kzalloc (i.e. 'dest').
2) Allocate 'src' with kmalloc instead of kzalloc as all elements of the
'src' buffer are initialized in a 'for(...)' loop just after.
3) remove useless 'sizeof(u8)', which always returns 1, when computing the
size of the memory to be allocated.
Signed-off-by: Christophe Jaillet <christophe.jaillet@wanadoo.fr>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
'ack' is currently a simple integer that flags whether or not a client is done
touching fields in the given descriptor. It is effectively just a single bit
of information. Converting this to a flags parameter allows the other bits to
be put to use to control completion actions, like dma-unmap, and capture
results, like xor-zero-sum == 0.
Changes are one of:
1/ convert all open-coded ->ack manipulations to use async_tx_ack
and async_tx_test_ack.
2/ set the ack bit at prep time where possible
3/ make drivers store the flags at prep time
4/ add flags to the device_prep_dma_interrupt prototype
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
DMA drivers no longer need to be notified of dependency submission
events as async_tx_run_dependencies and async_tx_channel_switch will
handle the scheduling and execution of dependent operations.
[sfr@canb.auug.org.au: extend this for fsldma]
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Shrink struct dma_async_tx_descriptor and introduce
async_tx_channel_switch to properly inject a channel switch interrupt in
the descriptor stream. This simplifies the locking model as drivers no
longer need to handle dma_async_tx_descriptor.lock.
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Split MPC83xx EOCDI event from MPC85xx EOLNI event, which is
also need to update cookie and start the next transfer.
The DMA channel irq handler function code is refined.
The patch is tested on MPC8377MDS board.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by; Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Always enabling the fsl_dma_self_test() to ensure the DMA controller
should works well after the driver probed.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Documentation/powerpc/booting-without-of.txt specifies the
compatiables we should bind to for this driver (elo, eloplus).
Use these instead of the extremely specific 'mpc8540' and 'mpc8349'
compatiables.
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
a) every bitwise declaration will give a unique type; use typedefs.
b) no need to bother with the stuff pointed to by iomem pointers,
unless it's accessed directly. noderef will force us to use helpers
anyway.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The DMA_INTERRUPT async_tx is a NULL transfer, thus the BCR(count register)
is 0. When the transfer started with a byte count of zero, the DMA
controller will triger a PE(programming error) event and halt, not a normal
interrupt. I add special codes for PE event and DMA_INTERRUPT
async_tx testing.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The patch 'fsldma: do not cleanup descriptors in hardirq context'
(commit 222ccf9ab8) removed descriptors
cleanup function to tasklet but the completed cookie do not updated.
Thus, the DMA controller will get lots of duplicated transfer
interrupts. Just make a completed cookie update in interrupt handler.
And keep other cleanup jobs in tasklet function.
Tested-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This is a bug that I assigned DMA_INTERRUPT capability to fsldma
but missing device_prep_dma_interrupt function. For a bug in
dmaengine.c the driver passed BUG_ON() checking. The patch fixes it.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The device->device_prep_dma_interrupt function is used by
DMA_INTERRUPT capability, not DMA_ZERO_SUM.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
There are warning messages reported by Stephen Rothwell with
ARCH=powerpc allmodconfig build:
drivers/dma/fsldma.c: In function 'fsl_dma_prep_memcpy':
drivers/dma/fsldma.c:439: warning: comparison of distinct pointer types
lacks a cast
drivers/dma/fsldma.c: In function 'fsl_chan_xfer_ld_queue':
drivers/dma/fsldma.c:584: warning: format '%016llx' expects type 'long long
unsigned int', but argument 4 has type 'dma_addr_t'
drivers/dma/fsldma.c: In function 'fsl_dma_chan_do_interrupt':
drivers/dma/fsldma.c:668: warning: format '%x' expects type 'unsigned int',
but argument 5 has type 'dma_addr_t'
drivers/dma/fsldma.c:684: warning: format '%016llx' expects type 'long long
unsigned int', but argument 4 has type 'dma_addr_t'
drivers/dma/fsldma.c:684: warning: format '%016llx' expects type 'long long
unsigned int', but argument 5 has type 'dma_addr_t'
drivers/dma/fsldma.c:701: warning: format '%02x' expects type 'unsigned
int', but argument 4 has type 'dma_addr_t'
drivers/dma/fsldma.c: In function 'fsl_dma_self_test':
drivers/dma/fsldma.c:840: warning: format '%d' expects type 'int', but
argument 5 has type 'size_t'
drivers/dma/fsldma.c: In function 'of_fsl_dma_probe':
drivers/dma/fsldma.c:1010: warning: format '%08x' expects type 'unsigned
int', but argument 5 has type 'resource_size_t'
This patch fixed the above warning messages.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Initialize 'ack' to zero in case the descriptor has been recycled.
Prevents "kernel BUG at crypto/async_tx/async_xor.c:185!"
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Cc: stable@kernel.org
"Cleaning" descriptors involves calling pending callbacks and clients
assume that their callback will only ever happen in softirq context.
Delay cleanup to the tasklet.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Zhang Wei <wei.zhang@freescale.com>
The driver implements DMA engine API for Freescale MPC85xx DMA controller,
which could be used by devices in the silicon. The driver supports the
Basic mode of Freescale MPC85xx DMA controller. The MPC85xx processors
supported include MPC8540/60, MPC8555, MPC8548, MPC8641 and so on.
The MPC83xx(MPC8349, MPC8360) are also supported.
[kamalesh@linux.vnet.ibm.com: build fix]
[dan.j.williams@intel.com: merge mm fixes, rebase on async_tx-2.6.25]
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Ebony Zhu <ebony.zhu@freescale.com>
Acked-by: Kumar Gala <galak@gate.crashing.org>
Cc: Shannon Nelson <shannon.nelson@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Pass a full set of flags to drivers' per-operation 'prep' routines.
Currently the only flag passed is DMA_PREP_INTERRUPT. The expectation is
that arch-specific async_tx_find_channel() implementations can exploit this
capability to find the best channel for an operation.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Reviewed-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
The tx_set_src and tx_set_dest methods were originally implemented to allow
an array of addresses to be passed down from async_xor to the dmaengine
driver while minimizing stack overhead. Removing these methods allows
drivers to have all transaction parameters available at 'prep' time, saves
two function pointers in struct dma_async_tx_descriptor, and reduces the
number of indirect branches..
A consequence of moving this data to the 'prep' routine is that
multi-source routines like async_xor need temporary storage to convert an
array of linear addresses into an array of dma addresses. In order to keep
the same stack footprint of the previous implementation the input array is
reused as storage for the dma addresses. This requires that
sizeof(dma_addr_t) be less than or equal to sizeof(void *). As a
consequence CONFIG_DMADEVICES now depends on !CONFIG_HIGHMEM64G. It also
requires that drivers be able to make descriptor resources available when
the 'prep' routine is polled.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
these three list_head are all local variables, but can also use LIST_HEAD.
Signed-off-by: Denis Cheng <crquan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tony Jones <tonyj@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Cc: Shannon Nelson <shannon.nelson@intel.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We can't use the device in a dev_err() after a kzalloc failure or after the
kfree, so simplify it to the pdev that was originally passed in.
Cc: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A few fixups from Andrew's code comments.
- removed "static inline" forward-declares
- changed use of min() to min_t()
- removed some unnecessary NULL initializations
- removed a couple of BUG() calls
Fixes this:
drivers/dma/ioat_dma.c: In function `ioat1_tx_submit':
drivers/dma/ioat_dma.c:177: sorry, unimplemented: inlining failed in call to '__ioat1_dma_memcpy_issue_pending': function body not available
drivers/dma/ioat_dma.c:268: sorry, unimplemented: called from here
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Cc: "Williams, Dan J" <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch corrects recently changed (and now invalid) Kconfig descriptions
for the DMA engine framework:
- Non-Intel(R) hardware also has DMA engines;
- DMA is used for more than memcpy and RAID offloading.
In fact, on most platforms memcpy and RAID aren't factors, and DMA
exists so that peripherals can transfer data to/from memory while
the CPU does other work.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for version 2 of the ioatdma device. This device handles
the descriptor chain and DCA services slightly differently:
- Instead of moving the dma descriptors between a busy and an idle chain,
this new version uses a single circular chain so that we don't have
rewrite the next_descriptor pointers as we add new requests, and the
device doesn't need to re-read the last descriptor.
- The new device has the DCA tags defined internally instead of needing
them defined statically.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Cc: "Williams, Dan J" <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a DMA device is unregistered, its reference count is decremented twice
for each channel: Once dma_class_dev_release() and once in
dma_chan_cleanup(). This may result in the DMA device driver's remove()
function completing before all channels have been cleaned up, causing lots
of use-after-free fun.
Fix it by incrementing the device's reference count twice for each
channel during registration.
[dan.j.williams@intel.com: kill unnecessary client refcounting]
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
No reason I can think of of making them default y Most people don't have
the hardware and with default y they just pollute lots of configs during
make oldconfig.
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Jeff Garzik <jeff@garzik.org>
Acked-by: "Nelson, Shannon" <shannon.nelson@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The async_tx interface includes a completion callback. This adds support
for using that callback, including using interrupts on completion.
[akpm@linux-foundation.org: various fixes]
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The change to the async_tx interface cost this driver some performance by
spreading the descriptor setup across several functions, including multiple
passes over the new descriptor chain. Here we bring the work back into one
primary function and only do one pass.
[akpm@linux-foundation.org: cleanups, uninline]
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make better use of dev_err(), and catch an error where the transaction
creation might fail.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don't start ioat_dca if ioat_dma didn't start, and then stop ioat_dca
before stopping ioat_dma. Since the ioat_dma side does the pci device
work, This takes care of ioat_dca trying to use a bad device reference.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reorder the pci release actions
Letting go of the resources in the right order helps get rid of
occasional kernel complaints.
Fix the pci_driver object name [Randy Dunlap]
Rename the struct pci_driver data so that false section mismatch
warnings won't be produced.
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adrian Bunk points out that "unsafe" was used to mark modules touched by
the deprecated MOD_INC_USE_COUNT interface, which has long gone. It's time
to remove the member from the module structure, as well.
If you want a module which can't unload, don't register an exit function.
(Vlad Yasevich says SCTP is now safe to unload, so just remove the
__unsafe there).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Cc: Sridhar Samudrala <sri@us.ibm.com>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add code to connect to the DCA driver and provide cpu tags for use by
drivers that would like to use Direct Cache Access hints.
[Adrian Bunk] Several Kconfig cleanup items
[Andrew Morten, Chris Leech] Fix for using cpu_physical_id() even when
built for uni-processor
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for MSI and MSI-X interrupt handling, including the ability
to choose the desired interrupt method.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: David S. Miller <davem@davemloft.net>
[bunk@kernel.org: drivers/dma/ioat_dma.c: make 3 functions static]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Split the general PCI startup from the DMA handling code in order to
prepare for adding support for DCA services and future versions of the
ioatdma device.
[Rusty Russell] Removal of __unsafe() usage.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Take care of a bunch of little code nits in ioatdma files
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rename the ioatdma.c file in preparation for splitting into multiple files,
which will allow for easier adding new functionality.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add device ids for new revs of the Intel I/OAT DMA engine
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that the DMA engine has a multi-client interface, fix the ioatdma
driver to play along. At the same time, remove a couple of unnecessary
reads and writes.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Al Viro pointed out that dma_memcpy_to_kernel_iovec() really was
unreachable and thus unused. The code originally was there to support
in-kernel dma needs, but since it remains unused, we'll pull it out.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Continuing the work started in 411f0f3edc ...
This enables code with a dma path, that compiles away, to build without
requiring additional code factoring. It also prevents code that calls
dma_alloc_coherent and dma_free_coherent from linking whereas previously
the code would hit a BUG() at run time. Finally, it allows archs that set
!HAS_DMA to delete their asm/dma-mapping.h file.
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Kyle McMartin <kyle@parisc-linux.org>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: <geert@linux-m68k.org>
Cc: <zippel@linux-m68k.org>
Cc: <spyro@f2s.com>
Cc: <ysato@users.sourceforge.jp>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: John Magolan <john.magolan@unisys.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The Intel(R) IOP series of i/o processors integrate an Xscale core with
raid acceleration engines. The capabilities per platform are:
iop219:
(2) copy engines
iop321:
(2) copy engines
(1) xor and block fill engine
iop33x:
(2) copy and crc32c engines
(1) xor, xor zero sum, pq, pq zero sum, and block fill engine
iop34x (iop13xx):
(2) copy, crc32c, xor, xor zero sum, and block fill engines
(1) copy, crc32c, xor, xor zero sum, pq, pq zero sum, and block fill engine
The driver supports the features of the async_tx api:
* asynchronous notification of operation completion
* implicit (interupt triggered) handling of inter-channel transaction
dependencies
The driver adapts to the platform it is running by two methods.
1/ #include <asm/arch/adma.h> which defines the hardware specific
iop_chan_* and iop_desc_* routines as a series of static inline
functions
2/ The private platform data attached to the platform_device defines the
capabilities of the channels
20070626: Callbacks are run in a tasklet. Given the recent discussion on
LKML about killing tasklets in favor of workqueues I did a quick conversion
of the driver. Raid5 resync performance dropped from 50MB/s to 30MB/s, so
the tasklet implementation remains until a generic softirq interface is
available.
Changelog:
* fixed a slot allocation bug in do_iop13xx_adma_xor that caused too few
slots to be requested eventually leading to data corruption
* enabled the slot allocation routine to attempt to free slots before
returning -ENOMEM
* switched the cleanup routine to solely use the software chain and the
status register to determine if a descriptor is complete. This is
necessary to support other IOP engines that do not have status writeback
capability
* make the driver iop generic
* modified the allocation routines to understand allocating a group of
slots for a single operation
* added a null xor initialization operation for the xor only channel on
iop3xx
* support xor operations on buffers larger than the hardware maximum
* split the do_* routines into separate prep, src/dest set, submit stages
* added async_tx support (dependent operations initiation at cleanup time)
* simplified group handling
* added interrupt support (callbacks via tasklets)
* brought the pending depth inline with ioat (i.e. 4 descriptors)
* drop dma mapping methods, suggested by Chris Leech
* don't use inline in C files, Adrian Bunk
* remove static tasklet declarations
* make iop_adma_alloc_slots easier to read and remove chances for a
corrupted descriptor chain
* fix locking bug in iop_adma_alloc_chan_resources, Benjamin Herrenschmidt
* convert capabilities over to dma_cap_mask_t
* fixup sparse warnings
* add descriptor flush before iop_chan_enable
* checkpatch.pl fixes
* gpl v2 only correction
* move set_src, set_dest, submit to async_tx methods
* move group_list and phys to async_tx
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The async_tx api provides methods for describing a chain of asynchronous
bulk memory transfers/transforms with support for inter-transactional
dependencies. It is implemented as a dmaengine client that smooths over
the details of different hardware offload engine implementations. Code
that is written to the api can optimize for asynchronous operation and the
api will fit the chain of operations to the available offload resources.
I imagine that any piece of ADMA hardware would register with the
'async_*' subsystem, and a call to async_X would be routed as
appropriate, or be run in-line. - Neil Brown
async_tx exploits the capabilities of struct dma_async_tx_descriptor to
provide an api of the following general format:
struct dma_async_tx_descriptor *
async_<operation>(..., struct dma_async_tx_descriptor *depend_tx,
dma_async_tx_callback cb_fn, void *cb_param)
{
struct dma_chan *chan = async_tx_find_channel(depend_tx, <operation>);
struct dma_device *device = chan ? chan->device : NULL;
int int_en = cb_fn ? 1 : 0;
struct dma_async_tx_descriptor *tx = device ?
device->device_prep_dma_<operation>(chan, len, int_en) : NULL;
if (tx) { /* run <operation> asynchronously */
...
tx->tx_set_dest(addr, tx, index);
...
tx->tx_set_src(addr, tx, index);
...
async_tx_submit(chan, tx, flags, depend_tx, cb_fn, cb_param);
} else { /* run <operation> synchronously */
...
<operation>
...
async_tx_sync_epilog(flags, depend_tx, cb_fn, cb_param);
}
return tx;
}
async_tx_find_channel() returns a capable channel from its pool. The
channel pool is organized as a per-cpu array of channel pointers. The
async_tx_rebalance() routine is tasked with managing these arrays. In the
uniprocessor case async_tx_rebalance() tries to spread responsibility
evenly over channels of similar capabilities. For example if there are two
copy+xor channels, one will handle copy operations and the other will
handle xor. In the SMP case async_tx_rebalance() attempts to spread the
operations evenly over the cpus, e.g. cpu0 gets copy channel0 and xor
channel0 while cpu1 gets copy channel 1 and xor channel 1. When a
dependency is specified async_tx_find_channel defaults to keeping the
operation on the same channel. A xor->copy->xor chain will stay on one
channel if it supports both operation types, otherwise the transaction will
transition between a copy and a xor resource.
Currently the raid5 implementation in the MD raid456 driver has been
converted to the async_tx api. A driver for the offload engines on the
Intel Xscale series of I/O processors, iop-adma, is provided in a later
commit. With the iop-adma driver and async_tx, raid456 is able to offload
copy, xor, and xor-zero-sum operations to hardware engines.
On iop342 tiobench showed higher throughput for sequential writes (20 - 30%
improvement) and sequential reads to a degraded array (40 - 55%
improvement). For the other cases performance was roughly equal, +/- a few
percentage points. On a x86-smp platform the performance of the async_tx
implementation (in synchronous mode) was also +/- a few percentage points
of the original implementation. According to 'top' on iop342 CPU
utilization drops from ~50% to ~15% during a 'resync' while the speed
according to /proc/mdstat doubles from ~25 MB/s to ~50 MB/s.
The tiobench command line used for testing was: tiobench --size 2048
--block 4096 --block 131072 --dir /mnt/raid --numruns 5
* iop342 had 1GB of memory available
Details:
* if CONFIG_DMA_ENGINE=n the asynchronous path is compiled away by making
async_tx_find_channel a static inline routine that always returns NULL
* when a callback is specified for a given transaction an interrupt will
fire at operation completion time and the callback will occur in a
tasklet. if the the channel does not support interrupts then a live
polling wait will be performed
* the api is written as a dmaengine client that requests all available
channels
* In support of dependencies the api implicitly schedules channel-switch
interrupts. The interrupt triggers the cleanup tasklet which causes
pending operations to be scheduled on the next channel
* Xor engines treat an xor destination address differently than a software
xor routine. To the software routine the destination address is an implied
source, whereas engines treat it as a write-only destination. This patch
modifies the xor_blocks routine to take a an explicit destination address
to mirror the hardware.
Changelog:
* fixed a leftover debug print
* don't allow callbacks in async_interrupt_cond
* fixed xor_block changes
* fixed usage of ASYNC_TX_XOR_DROP_DEST
* drop dma mapping methods, suggested by Chris Leech
* printk warning fixups from Andrew Morton
* don't use inline in C files, Adrian Bunk
* select the API when MD is enabled
* BUG_ON xor source counts <= 1
* implicitly handle hardware concerns like channel switching and
interrupts, Neil Brown
* remove the per operation type list, and distribute operation capabilities
evenly amongst the available channels
* simplify async_tx_find_channel to optimize the fast path
* introduce the channel_table_initialized flag to prevent early calls to
the api
* reorganize the code to mimic crypto
* include mm.h as not all archs include it in dma-mapping.h
* make the Kconfig options non-user visible, Adrian Bunk
* move async_tx under crypto since it is meant as 'core' functionality, and
the two may share algorithms in the future
* move large inline functions into c files
* checkpatch.pl fixes
* gpl v2 only correction
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-By: NeilBrown <neilb@suse.de>
The current implementation assumes that a channel will only be used by one
client at a time. In order to enable channel sharing the dmaengine core is
changed to a model where clients subscribe to channel-available-events.
Instead of tracking how many channels a client wants and how many it has
received the core just broadcasts the available channels and lets the
clients optionally take a reference. The core learns about the clients'
needs at dma_event_callback time.
In support of multiple operation types, clients can specify a capability
mask to only be notified of channels that satisfy a certain set of
capabilities.
Changelog:
* removed DMA_TX_ARRAY_INIT, no longer needed
* dma_client_chan_free -> dma_chan_release: switch to global reference
counting only at device unregistration time, before it was also happening
at client unregistration time
* clients now return dma_state_client to dmaengine (ack, dup, nak)
* checkpatch.pl fixes
* fixup merge with git-ioat
Cc: Chris Leech <christopher.leech@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: David S. Miller <davem@davemloft.net>
The current dmaengine interface defines mutliple routines per operation,
i.e. dma_async_memcpy_buf_to_buf, dma_async_memcpy_buf_to_page etc. Adding
more operation types (xor, crc, etc) to this model would result in an
unmanageable number of method permutations.
Are we really going to add a set of hooks for each DMA engine
whizbang feature?
- Jeff Garzik
The descriptor creation process is refactored using the new common
dma_async_tx_descriptor structure. Instead of per driver
do_<operation>_<dest>_to_<src> methods, drivers integrate
dma_async_tx_descriptor into their private software descriptor and then
define a 'prep' routine per operation. The prep routine allocates a
descriptor and ensures that the tx_set_src, tx_set_dest, tx_submit routines
are valid. Descriptor creation and submission becomes:
struct dma_device *dev;
struct dma_chan *chan;
struct dma_async_tx_descriptor *tx;
tx = dev->device_prep_dma_<operation>(chan, len, int_flag)
tx->tx_set_src(dma_addr_t, tx, index /* for multi-source ops */)
tx->tx_set_dest(dma_addr_t, tx, index)
tx->tx_submit(tx)
In addition to the refactoring, dma_async_tx_descriptor also lays the
groundwork for definining cross-channel-operation dependencies, and a
callback facility for asynchronous notification of operation completion.
Changelog:
* drop dma mapping methods, suggested by Chris Leech
* fix ioat_dma_dependency_added, also caught by Andrew Morton
* fix dma_sync_wait, change from Andrew Morton
* uninline large functions, change from Andrew Morton
* add tx->callback = NULL to dmaengine calls to interoperate with async_tx
calls
* hookup ioat_tx_submit
* convert channel capabilities to a 'cpumask_t like' bitmap
* removed DMA_TX_ARRAY_INIT, no longer needed
* checkpatch.pl fixes
* make set_src, set_dest, and tx_submit descriptor specific methods
* fixup git-ioat merge
* move group_list and phys to dma_async_tx_descriptor
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Chris Leech <christopher.leech@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: David S. Miller <davem@davemloft.net>
Under kexec, I/OAT initialization breaks over busy resources because the
previous kernel did not release them.
I'm not sure this fix can be considered a complete one but it works for me.
I guess something similar to the *_remove method should occur there..
Signed-off-by: Dan Aloni <da-x@monatomic.org>
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
There's only one now anyway, and it's not in a performance path,
so make it behave the same on 32-bit and 64-bit CPUs.
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Every 20 descriptors turns out to be to few append commands with
newer/faster CPUs. Pushing every 4 still cuts down on MMIO writes to an
acceptable level without letting the DMA engine run out of work.
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Rename struct pci_driver data so that false section mismatch warnings won't
be produced.
Sam, ISTM that depending on variable names is the weakest & worst part of
modpost section checking. Should __init_refok work here? I got build
errors when I tried to use it, probably because the struct pci_driver probe
and remove methods are not marked "__init_refok".
WARNING: drivers/dma/ioatdma.o(.data+0x10): Section mismatch: reference to .init.text: (between 'ioat_pci_drv' and 'ioat_pci_tbl')
WARNING: drivers/dma/ioatdma.o(.data+0x14): Section mismatch: reference to .exit.text: (between 'ioat_pci_drv' and 'ioat_pci_tbl')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Chris Leech <christopher.leech@intel.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Disable some more menus in the configuration files that are of no
interest to a s390 machine.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This removes several pointless exports from drivers/dma/dmaengine.c; the
dma_async_memcpy_*() functions are inlined by <linux/dmaengine.h> so those
exports are inappropriate.
It also moves the existing EXPORT_SYMBOL declarations next to their functions,
so it's now trivial to confirm one-to-one correspondence between exports and
nonstatic symbols.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SLAB_KERNEL is an alias of GFP_KERNEL.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
Changes pci_module_init() to pci_register_driver().
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix kernel-doc warnings in drivers/dma/:
- use correct function & parameter names
- add descriptions where omitted
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/dma/ioatdma.c: In function 'ioat_init_module':
drivers/dma/ioatdma.c:830: warning: control reaches end of non-void function
Signed-off-by: Benoit Boissinot <benoit.boissinot@ens-lyon.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the needlessly global num_pages_spanned() static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warning:
drivers/dma/ioatdma.c:444:32: warning: constant 0xFFFFFFFFFFFFFFC0 is so big it is unsigned long
Also needs a MAINTAINERS entry.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
for_each_cpu() is going away (and is gone in -mm).
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provides for pinning user space pages in memory, copying to iovecs,
and copying from sk_buffs including fragmented and chained sk_buffs.
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Attempts to allocate per-CPU DMA channels
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provides an API for offloading memory copies to DMA devices
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
