For the dual-role port, it will assign the phy dev to usb-phy dev and
use the port dev driver as the dev driver of usb-phy.
When we try to destroy the port dev, it will destroy its dev driver
as well. But we did not remove the reference from usb-phy dev. This
might cause the use-after-free issue in KASAN.
Fixes: e8f7d2f409 ("phy: tegra: xusb: Add usb-phy support")
Cc: stable@vger.kernel.org
Signed-off-by: EJ Hsu <ejh@nvidia.com>
Signed-off-by: Haotien Hsu <haotienh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20230609062932.3276509-1-haotienh@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The tegra_xusb_port_unregister should be called when usb2_port
and ulpi_port map fails in tegra_xusb_add_usb2_port() or in
tegra_xusb_add_ulpi_port(), fix it.
Fixes: 53d2a715c2 ("phy: Add Tegra XUSB pad controller support")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20221129111634.1547747-1-cuigaosheng1@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add new registers programming in sleepwalk sequence for Tegra234:
MASTER_ENABLE_A/B/C/D in XUSB_AO_UTMIP_SLEEPWALK.
Signed-off-by: Henry Lin <henryl@nvidia.com>
Signed-off-by: Haotien Hsu <haotienh@nvidia.com>
Link: https://lore.kernel.org/r/20230309061708.4156383-1-haotienh@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230307115900.2293120-25-u.kleine-koenig@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for the XUSB pad controller found on Tegra234 SoCs. It is
mostly similar to the same IP found on Tegra194, because most of
the Tegra234 XUSB PADCTL registers definition and programming sequence
are the same as Tegra194, Tegra234 XUSB PADCTL can share the same
driver with Tegra186 and Tegra194 XUSB PADCTL.
Introduce a new feature, USB2 HW tracking, for Tegra234.
The feature is to enable HW periodical PAD tracking which measure
and capture the electric parameters of USB2.0 PAD.
Signed-off-by: Sing-Han Chen <singhanc@nvidia.com>
Co-developed-by: Wayne Chang <waynec@nvidia.com>
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20230111110450.24617-6-jonathanh@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Pad tracking is a one-time calibration for Tegra186 and Tegra194.
Clk should be disabled after calibration.
Disable clk after calibration.
While at it add 100us delay for HW recording the calibration value.
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20230111110450.24617-5-jonathanh@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Remove redundant codes for getting the vbus supply of usb3 ports because
we get and control the vbus supply by the companion usb2 ports
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Signed-off-by: Haotien Hsu <haotienh@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20221005084031.2154251-1-haotienh@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Set ENABLE_L2_EXIT_RATE_CHANGE register bit to request UPHY PLL rate change
to Gen1 during initialization. This helps in the below surprise link down
cases,
- Surprise link down happens at Gen3/Gen4 link speed.
- Surprise link down happens and external REFCLK is cut off, which causes
UPHY PLL rate to deviate to an invalid rate.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Link: https://lore.kernel.org/r/20221013183854.21087-9-vidyas@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit a88520bfc0 ("usb: gadget: tegra: Reduce pad power") added calls
to tegra_phy_xusb_utmi_pad_power_on/down in the Tegra XUDC driver to
control the pad power. This change is causing a kernel panic when
powering down the pads on entering suspend with the Jetson TX2 platform.
The panic occurs because the 'xudc->curr_utmi_phy' is not configured on
this platform and we do not check to see if the pointer is valid before
attempting to deference the pointer. Fix this by checking to see if the
'phy' pointer passed to tegra_phy_xusb_utmi_pad_power_on/down is valid.
Fixes: a88520bfc0 ("usb: gadget: tegra: Reduce pad power")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20221010135132.30809-1-jonathanh@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Here is the big set of USB and Thunderbolt driver changes for 6.1-rc1.
Nothing major in here, lots of little things with new devices supported
and updates for a few drivers. Highlights include:
- thunderbolt/USB4 devices supported a bit better than before,
and some new ids to enable new hardware devices
- USB gadget uvc updates for newer video formats and better v4l
integration (the v4l portions were acked by those maintainers)
- typec updates for tiny issues and more typec drivers for new
chips.
- xhci tiny updates for minor issues
- big usb-serial ftdi_sio driver update to handle new devices
better
- lots of tiny dwc3 fixes and updates for the IP block that is
showing up everywhere these days
- dts updates for new devices being supported
- other tiny janitorial and cleanups fixes for lots of different
USB drivers. Full details are in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY0BN9g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yljdgCdH4Fev4Nvf2Nokfv0q0krcRB3YpUAn1aZfpb/
EbgxsxhPnTJg+mmXyLms
=IxUy
-----END PGP SIGNATURE-----
Merge tag 'usb-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt driver changes for 6.1-rc1.
Nothing major in here, lots of little things with new devices
supported and updates for a few drivers. Highlights include:
- thunderbolt/USB4 devices supported a bit better than before, and
some new ids to enable new hardware devices
- USB gadget uvc updates for newer video formats and better v4l
integration (the v4l portions were acked by those maintainers)
- typec updates for tiny issues and more typec drivers for new chips.
- xhci tiny updates for minor issues
- big usb-serial ftdi_sio driver update to handle new devices better
- lots of tiny dwc3 fixes and updates for the IP block that is
showing up everywhere these days
- dts updates for new devices being supported
- other tiny janitorial and cleanups fixes for lots of different USB
drivers. Full details are in the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (169 commits)
usb: gadget: uvc: don't put item still in use
usb: gadget: uvc: Fix argument to sizeof() in uvc_register_video()
usb: host: ehci-exynos: switch to using gpiod API
Revert "usb: dwc3: Don't switch OTG -> peripheral if extcon is present"
Revert "USB: fixup for merge issue with "usb: dwc3: Don't switch OTG -> peripheral if extcon is present""
dt-bindings: usb: Convert FOTG210 to dt schema
usb: mtu3: fix failed runtime suspend in host only mode
USB: omap_udc: Fix spelling mistake: "tranceiver_ctrl" -> "transceiver_ctrl"
usb: typec: ucsi_ccg: Disable UCSI ALT support on Tegra
usb: typec: Replace custom implementation of device_match_fwnode()
usb: typec: ucsi: Don't warn on probe deferral
usb: add quirks for Lenovo OneLink+ Dock
MAINTAINERS: switch dwc3 to Thinh
usb: idmouse: fix an uninit-value in idmouse_open
USB: PHY: JZ4770: Switch to use dev_err_probe() helper
usb: phy: generic: Switch to use dev_err_probe() helper
usb: ulpi: use DEFINE_SHOW_ATTRIBUTE to simplify ulpi_regs
usb: cdns3: remove dead code
usb: cdc-wdm: Use skb_put_data() instead of skb_put/memcpy pair
usb: musb: sunxi: Switch to use dev_err_probe() helper
...
This patch enables the usb-role-switch attribute and lets users check
the current device role of the otg capability ports
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Signed-off-by: Haotien Hsu <haotienh@nvidia.com>
Link: https://lore.kernel.org/r/20220928125640.2219402-1-haotienh@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In the probe path, dev_err() can be replaced with dev_err_probe()
which will check if error code is -EPROBE_DEFER and prints the
error name. It also sets the defer probe reason which can be
checked later through debugfs.
Signed-off-by: Yuan Can <yuancan@huawei.com>
Link: https://lore.kernel.org/r/20220922092243.22281-1-yuancan@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The single difference between returning 0 and returning an error code in
a platform remove callback is that in the latter case the platform core
emits a warning about the error being ignored.
If reset_control_assert() fails there is already a warning, so suppress
the more generic (and less helpful) by returning 0 in
tegra_xusb_padctl_remove().
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220716145403.107703-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add utmi_pad_power_on/down ops for each SOC instead of exporting
tegra_phy_xusb_utmi_pad_power_on/down directly for Tegra186 chip.
Signed-off-by: BH Hsieh <bhsieh@nvidia.com>
Signed-off-by: Jim Lin <jilin@nvidia.com>
Link: https://lore.kernel.org/r/20220816082353.13390-2-jilin@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Synopsys DesignWare core based PCIe controllers in Tegra234 SoC
interface with Universal PHY (UPHY) module through a PIPE2UPHY (P2U)
module. For each PCIe lane of a controller, there is a P2U unit
instantiated at hardware level. This driver provides support for the
programming required for each P2U that is going to be used for a PCIe
controller.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Link: https://lore.kernel.org/r/20220629060435.25297-9-vidyas@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
callers of tegra_xusb_find_port_node() function only do NULL checking for
the return value. return NULL instead of ERR_PTR(-ENOMEM) to keep
consistent.
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20211213020507.1458-1-linmq006@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When these are not referenced, gcc prints a harmless warning:
drivers/phy/tegra/xusb.c:1286:12: error: 'tegra_xusb_padctl_resume_noirq' defined but not used [-Werror=unused-function]
1286 | static int tegra_xusb_padctl_resume_noirq(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/phy/tegra/xusb.c:1276:12: error: 'tegra_xusb_padctl_suspend_noirq' defined but not used [-Werror=unused-function]
1276 | static int tegra_xusb_padctl_suspend_noirq(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: c545a90567 ("phy: tegra: xusb: Add sleepwalk and suspend/resume")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210721152550.2976003-1-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
To support XUSB host controller ELPG, this commit moves VBUS control
.phy_power_on()/.phy_power_off() to .phy_init()/.phy_exit().
When XUSB host controller enters ELPG, host driver invokes
.phy_power_off(), VBUS should remain ON so that USB devices will not
disconnect. VBUS can be turned OFF when host driver invokes
.phy_exit() which indicates disabling a USB port.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This commit implements Tegra210 XUSB PADCTL wake and sleepwalk
routines. Sleepwalk logic is in PMC (always-on) hardware block.
PMC driver provides managed access to the sleepwalk registers
via regmap framework.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This commit adds sleepwalk/wake and suspend/resume interfaces
to Tegra XUSB PHY driver.
Tegra XUSB host controller driver makes use of sleepwalk functions
to enable/disable sleepwalk circuit which is in always-on partition
and can respond to USB resume signals when controller is not powered.
Sleepwalk can be enabled/disabled for any USB UPHY individually.
- tegra_xusb_padctl_enable_phy_sleepwalk()
- tegra_xusb_padctl_disable_phy_sleepwalk()
Tegra XUSB host controller driver makes use of wake functions to
enable/disable/query wake circuit which is in always-on partition
can wake system up when USB resume happens.
Wake circuit can be enabled/disabled for any USB PHY individually.
- tegra_xusb_padctl_enable_phy_wake()
- tegra_xusb_padctl_disable_phy_wake()
- tegra_xusb_padctl_remote_wake_detected()
This commit also adds two system suspend stubs that can be used to
save and restore XUSB PADCTL context during system suspend and
resume.
- tegra_xusb_padctl_suspend_noirq()
- tegra_xusb_padctl_resume_noirq()
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
As per Tegra210 TRM, before changing lane assignments, driver should
keep lanes in IDDQ and sleep state; after changing lane assignments,
driver should bring lanes out of IDDQ.
This commit implements the required operations.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This commit is a preparation for enabling XUSB SC7 support.
It rearranges Tegra210 XUSB PADCTL UPHY initialization sequence,
for the following reasons:
1. PLLE hardware power sequencer has to be enabled only after both
PEX UPHY PLL and SATA UPHY PLL are initialized.
tegra210_uphy_init() -> tegra210_pex_uphy_enable()
-> tegra210_sata_uphy_enable()
-> tegra210_plle_hw_sequence_start()
-> tegra210_aux_mux_lp0_clamp_disable()
2. At cold boot and SC7 exit, the following bits must be cleared after
PEX/SATA lanes are out of IDDQ (IDDQ_DISABLE=1).
a. XUSB_PADCTL_ELPG_PROGRAM1_AUX_MUX_LP0_CLAMP_EN,
b. XUSB_PADCTL_ELPG_PROGRAM1_AUX_MUX_LP0_CLAMP_EN_EARLY
c. XUSB_PADCTL_ELPG_PROGRAM1_AUX_MUX_LP0_VCORE_DOWN
tegra210_pex_uphy_enable() and tegra210_sata_uphy_enable() are in
charge of bringing lanes out of IDDQ, and then AUX_MUX_LP0_* bits
will be cleared by tegra210_aux_mux_lp0_clamp_disable().
3. Once UPHY PLL hardware power sequencer is enabled, do not assert
reset to PEX/SATA PLLs, otherwise UPHY PLL operation will be broken.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The programming sequence in tegra210_usb3_port_enable() is required
for both cold boot and SC7 exit, and must be performed only after
PEX/SATA UPHY is initialized. Therefore, this commit moves the
programming sequence to tegra210_usb3_phy_power_on(). PCIE/SATA phy
.power_on() stub will invoke tegra210_usb3_phy_power_on() if the lane
is assigned for XUSB super-speed.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
- New phy drivers:
- Mediatek MT7621 PCIe PHY (promoted from staging)
- Ingenic USB phy driver supporting JZ4775 and X2000
- Intel Keem Bay USB PHY driver
- Marvell USB HSIC PHY driver supporting MMP3 SoC
- AXG MIPI D-PHY driver
- Updates:
- Conversion to YAML binding for:
- Broadcom SATA PHY
- Cadence Sierra PHY bindings
- STM32 USBC Phy
- Support for Exynos5433 PCIe PHY
- Support for Qualcomm SM8250 PCIe QMP PHY
- Support for Exynos5420 USB2 phy
- devm_platform_ioremap_resource conversion for bunch of drivers
-----BEGIN PGP SIGNATURE-----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=EFMp
-----END PGP SIGNATURE-----
Merge tag 'phy-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy into char-misc-next
Vinod writes:
phy-for-5.11
- New phy drivers:
- Mediatek MT7621 PCIe PHY (promoted from staging)
- Ingenic USB phy driver supporting JZ4775 and X2000
- Intel Keem Bay USB PHY driver
- Marvell USB HSIC PHY driver supporting MMP3 SoC
- AXG MIPI D-PHY driver
- Updates:
- Conversion to YAML binding for:
- Broadcom SATA PHY
- Cadence Sierra PHY bindings
- STM32 USBC Phy
- Support for Exynos5433 PCIe PHY
- Support for Qualcomm SM8250 PCIe QMP PHY
- Support for Exynos5420 USB2 phy
- devm_platform_ioremap_resource conversion for bunch of drivers
* tag 'phy-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (72 commits)
drm/mediatek: avoid dereferencing a null hdmi_phy on an error message
phy: ingenic: depend on HAS_IOMEM
phy: mediatek: statify mtk_hdmi_phy_driver
dt-bindings: phy: Convert Broadcom SATA PHY to YAML
devicetree: phy: rockchip-emmc add output-tapdelay-select
phy: rockchip-emmc: output tap delay dt property
PHY: Ingenic: Add USB PHY driver using generic PHY framework.
dt-bindings: USB: Add bindings for Ingenic JZ4775 and X2000.
USB: PHY: JZ4770: Remove unnecessary function calls.
devicetree: phy: rockchip-emmc: pulldown property
phy: rockchip: set pulldown for strobe line in dts
phy: renesas: rcar-gen3-usb2: disable runtime pm in case of failure
phy: mediatek: allow compile-testing the hdmi phy
phy/rockchip: Make PHY_ROCKCHIP_INNO_HDMI depend on HAS_IOMEM to fix build error
phy: samsung: Merge Kconfig for Exynos5420 and Exynos5250
phy: ralink: phy-mt7621-pci: set correct name in MODULE_DEVICE_TABLE macro
phy: ralink: phy-mt7621-pci: drop 'COMPILE_TEST' from Kconfig
phy: mediatek: Make PHY_MTK_{XSPHY, TPHY} depend on HAS_IOMEM and OF_ADDRESS to fix build errors
phy: tegra: xusb: Fix usb_phy device driver field
phy: amlogic: replace devm_reset_control_array_get()
...
Deferred probe is an expected return value for devm_regulator_bulk_get().
Given that the driver deals with it properly, there's no need to output a
warning that may potentially confuse users.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: JC Kuo <jckuo@nvidia.com>
Link: https://lore.kernel.org/r/20201111103708.152566-1-jonathanh@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The only usage of tegra_xusb_pad_type and tegra_xusb_port_type is to
assign their address to the type field in the device struct, which is a
const pointer. Make them const to allow the compiler to put them in
read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20201109215844.167954-1-rikard.falkeborn@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The usb_get_maximum_speed() function is part of the usb-common module,
so enable it by selecting the corresponding Kconfig symbol.
While at it, also make sure to depend on USB_SUPPORT because USB_PHY
requires that. This can lead to Kconfig conflicts if USB_SUPPORT is not
enabled while attempting to enable PHY_TEGRA_XUSB.
Reported-by: kbuild test robot <lkp@intel.com>
Suggested-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20200330101038.2422389-1-thierry.reding@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I have hit the following build error:
armv7a-hardfloat-linux-gnueabi-ld: drivers/phy/tegra/xusb.o: in function `tegra_xusb_port_unregister':
xusb.c:(.text+0x2ac): undefined reference to `usb_remove_phy'
armv7a-hardfloat-linux-gnueabi-ld: drivers/phy/tegra/xusb.o: in function `tegra_xusb_setup_ports':
xusb.c:(.text+0xf30): undefined reference to `usb_add_phy_dev'
PHY_TEGRA_XUSB should select USB_PHY because it uses symbols defined in
the code enabled by that.
Fixes: 23babe30fb45d ("phy: tegra: xusb: Add usb-phy support")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The device-managed allocation API doesn't work well with the life-cycle
of device objects. Since ports have device objects allocated within, it
can lead to situations where these devices need to stay around until
after their parent pad controller has been unbound from its driver. The
device-managed memory allocated for the port objects will, however, get
freed when the pad controller unbinds from the driver. This can cause
use-after-free errors down the road.
Note that the device is deleted as part of the driver unbind operation,
so there isn't much that can be done with it after that point, but the
memory still needs to stay around to ensure none of the references are
invalidated.
One situation where this arises is when a VBUS supply is associated with
a USB 2 or 3 port. When that supply is released using regulator_put() an
SRCU call will queue the release of the device link connecting the port
and the regulator after a grace period. This means that the regulator is
going to keep on to the last reference of the port device even after the
pad controller driver was unbound (which is when the memory backing the
port device is freed).
Fix this by allocating port objects using non-device-managed memory. Add
release callbacks for these objects so that their memory gets freed when
the last reference goes away. This decouples the port devices' lifetime
from the "active" lifetime of the pad controller (i.e. the time during
which the pad controller driver owns the device).
Signed-off-by: Thierry Reding <treding@nvidia.com>
Devices are created for each port of the XUSB pad controller. Each USB 2
and USB 3 port can potentially have an associated VBUS power supply that
needs to be removed when the device is removed.
Since port devices never bind to a driver, the driver core will not get
to perform the cleanup of device-managed resources that usually happens
on driver unbind.
Now, the driver core will also perform device-managed resource cleanup
for driver-less devices when they are released. However, when a device
link is created between the regulator and the port device, as part of
regulator_get(), the regulator takes a reference to the port device and
prevents it from being released unless regulator_put() is called, which
will never happen.
Avoid this by using the non-device-managed API and manually releasing
the regulator reference when the port is unregistered.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Probe deferral is an expected error condition that will usually be
recovered from. Print such error messages at debug level to make them
available for diagnostic purposes when building with debugging enabled
and hide them otherwise to not spam the kernel log with them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Deferred probe is an expected return value for tegra_fuse_readl().
Given that the driver deals with it properly, there's no need to
output a warning that may potentially confuse users.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for the XUSB pad controller found on Tegra194 SoCs. It is
mostly similar to the same IP found on Tegra186, but the number of
pads exposed differs, as do the programming sequences. Because most of
the Tegra194 XUSB PADCTL registers definition and programming sequence
are the same as Tegra186, Tegra194 XUSB PADCTL can share the same
driver, xusb-tegra186.c, with Tegra186 XUSB PADCTL.
Tegra194 XUSB PADCTL supports up to USB 3.1 Gen 2 speed, however, it
is possible for some platforms have long signal trace that could not
provide sufficient electrical environment for Gen 2 speed. This patch
adds a "maximum-speed" property to usb3 ports which can be used to
specify the maximum supported speed for any particular USB 3.1 port.
For a port that is not capable of SuperSpeedPlus, "maximum-speed"
property should carry "super-speed".
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
As xusb-tegra186.c will be reused for Tegra194, it would be good to
protect Tegra186 soc data with CONFIG_ARCH_TEGRA_186_SOC. This commit
also reshuffles Tegra186 soc data single CONFIG_ARCH_TEGRA_186_SOC
will be sufficient.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for set_mode on UTMI phy. This allow XUSB host/device mode
drivers to configure the hardware to corresponding modes.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for set_mode on USB 2 phy. This allow XUSB host/device mode
drivers to configure the hardware to corresponding modes.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra XUSB host, device mode driver requires the USB 3 companion port
number for corresponding USB 2 port. Add API to retrieve the same.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Reviewed-by: JC Kuo <jckuo@nvidia.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
For USB 2 ports that has usb-role-switch enabled, add usb-phy for
corresponding USB 2 phy. USB role changes from role switch are then
updated to corresponding host and device mode drivers via usb-phy notifier
block.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
[treding@nvidia.com: rebase onto Greg's usb-next branch]
Signed-off-by: Thierry Reding <treding@nvidia.com>
If usb-role-switch property is present in USB 2 port, register
usb-role-switch to receive usb role changes.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
[treding@nvidia.com: rebase onto Greg's usb-next branch]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use the new regulator helper instead of a for loop.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tegra XUSB device control driver needs to control vbus override
during its operations, add API for the support.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tegra XUSB device control driver needs to control vbus override
during its operations, add API for the support.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
On Tegra210, usb2 only otg/peripheral ports dont work in device mode.
They need an assosciated usb3 port to work in device mode. Identify
an unused usb3 port and assign it as a fake USB3 port to USB2 only
port whose mode is otg/peripheral.
Based on work by BH Hsieh <bhsieh@nvidia.com>.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
