Use clock definitions in i.MX27 DTS files.
Additional changes included in this patch (imx27.dtsi):
- Fix IPG clock for UART6.
- Use EMI_AHB_GATE clock for WEIM.
- Added GPIO_IPG_GATE clock for GPIO nodes. Currently this clock is
not used by the driver, but it can be added in the future.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
It is not a good approach to have the USB PHY nodes inside imx27.dtsi since
the USB PHYs on mx27 are not internal to the SoC.
Place the USB PHY nodes in the board dts files instead.
Also, each board may have a different clock source for the USB PHY, so do not
hardcode it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
USB Host1, Host2 and OTG are gated via 'usb_ipg_gate' clock, so fix it in order
to avoid the following kernel oops:
usbcore: registered new interface driver usb-storage
10024000.usb supply vbus not found, using dummy regulator
Unhandled fault: external abort on non-linefetch (0x808) at 0xf4424184
Internal error: : 808 [#1] PREEMPT ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 3.15.0-rc1-26325-g971f9fd-dirty #64
task: c7829aa0 ti: c7836000 task.ti: c7836000
PC is at ci_hdrc_probe+0x3a4/0x634
LR is at ci_hdrc_probe+0x100/0x634
pc : [<c036cc78>] lr : [<c036c9d4>] psr: 60000013
sp : c7837d48 ip : 00000001 fp : 00000000
r10: 00000000 r9 : 00000000 r8 : c791b6c0
r7 : c7945000 r6 : f4424000 r5 : c7945010 r4 : c794e010
r3 : f4424184 r2 : 00000000 r1 : 8c000004 r0 : 0c000004
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 0005317f Table: a0004000 DAC: 00000017
Process swapper (pid: 1, stack limit = 0xc78361c0)
Stack: (0xc7837d48 to 0xc7838000)
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Add alias for FEC ethernet on i.MX to allow bootloaders (like U-Boot)
patch-in the MAC address for FEC using this alias.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Per bindings of fixed-clock, #clock-cells is a required property. Let's
add it for those fixed rate clocks.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch adds the missing (Universal serial bus) USB devicetree
nodes for i.MX27 CPUs.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds the missing (Synchronous Serial Interface) SSI1 & SSI2
devicetree nodes for i.MX27 CPUs.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds a iomux node for imx27 pinctrl driver. The gpio
registers are embedded in the iomux memory area. So this patch moves
them into the iomux node for a better hardware description.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The pwm-node is missing its #pwm-cells property. The pwm-framework will
complain about this.
Add the missing property.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
AUDMUX expects additional parameters to be configured correctly,
so turn it off into a template.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Clock name is not needed for "cpufreq-cpu0".
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
i.MX27 CPU can be clocked with a 32 kHz quartz, and not just 32768 Hz,
so increase "clock-latency" value, which will ensure that we use two
clock cycles on frequency change.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add a label to i.MX27 CPU node. This change allows the reuse this node
in the upper levels of the DTS.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds core voltages for i.MX27 CPUs. Only 266 and 400 MHz modes
is documented in the datasheet, so we add a 266 MHz frequency for conform this.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch moves IIM node under AIPI2 bus, since this is proper
location for this module.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Set operating-points for imx27. There is no regulator support, so the
voltages are 0. The frequencies should be the same for all imx27 boards,
so it is defined here and can be overwritten if necessary.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
On the MX27 Reference Manual the interrupt controller is named AITC:
ARM926EJ-S Interrupt Controller
So use the AITC term instead of AVIC.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Origin: id:1334193132-18944-2-git-send-email-festevam@gmail.com
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This allows to order the i2c devices correctly.
While at it reorder the aliases entries alphabetically.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
i.MX27 have only one PWM, so index from PWM devicetree node removed.
Signed-off-by: Alexander Shiyan <eagle.alexander923@gmail.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds the missing (Symmetric/Asymmetric Hashing and Random
Accelerator) SAHARA2 devicetree node for i.MX27 CPUs.
Signed-off-by: Alexander Shiyan <eagle.alexander923@gmail.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds the missing VPU devicetree node for i.MX27 CPUs.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The CSPI controller has only one clock, but the driver spi-imx.c needs
clock "per" to calculate bitrate divisor.
Signed-off-by: Jonas Andersson <jonas@microbit.se>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The GPT is the GPT timer found on i.MX SoCs.
This adds the missing GPT devicetree nodes. Also fixup the watchdog
register map size along the way. it's 0x1000, not 0x4000. This didn't
hurt before as the region was not occupied by another device, but now
overlaps with the GPT.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Similarly as it was done for mx6q, use a DT lookup in order to make maintainance
task for the clock devices easier.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Replace /include/ (dtc) with #include (C pre-processor) for all imx DT
files, so that gcc -E handles the entire include tree, and hence any of
those files can #include some other file e.g. for constant definitions.
This allows future use of #defines and header files in order to define
names for various constants, such as pinctrl settings. Use of those
features will increase the readability of the device tree files.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Having labels before each node allows board bindings to reference
to nodes by using the &nodename {} notation. This way boards do not
have to resemble the whole devicetree layout. Due to less indention
needed the board files also get better readability. Since the label
make the documentation behind the nodes unnecessary it is removed.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This is some amount of work left/forgot from device tree conversion.
Instead of checking cpu_is_xxx to determine the controller type, the
driver should use platform_device_id, which should match the device
tree compatible string.
The patch changes the driver to use platform_device_id rather than
cpu_is_xxx to determine the controller type/version. It also updates
the platform code and device tree source accordingly.
As the result, mach/hardware.h inclusion gets removed from the driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: linux-i2c@vger.kernel.org
Instead of enabling the watchdog in each individual dts file, select in
the SoC dtsi file instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add alias for gpio nodes, so that gpio driver can identify the port
number and then specify a sensible gpio base rather than using the
one dynamically allocated by gpio core.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Change the value of #interrupt-cells of gpio nodes from 1 to 2, so that
the gpio irq type can be specified in device tree. Also update binding
document to make it clear.
Reported-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
- Updates to mxc_nand and gpmi drivers to support new boards and device tree
- Improve consistency of information about ECC strength in NAND devices
- Clean up partition handling of plat_nand
- Support NAND drivers without dedicated access to OOB area
- BCH hardware ECC support for OMAP
- Other fixes and cleanups, and a few new device IDs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAk/JG1wACgkQdwG7hYl686M80wCglN4kutx20j+KJWuZofkr9Hog
weEAoI4jrqEWEdW9EcT2CIWQw7eG+1v+
=7tdo
-----END PGP SIGNATURE-----
Merge tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd
Pull mtd update from David Woodhouse:
- More robust parsing especially of xattr data in JFFS2
- Updates to mxc_nand and gpmi drivers to support new boards and device tree
- Improve consistency of information about ECC strength in NAND devices
- Clean up partition handling of plat_nand
- Support NAND drivers without dedicated access to OOB area
- BCH hardware ECC support for OMAP
- Other fixes and cleanups, and a few new device IDs
Fixed trivial conflict in drivers/mtd/nand/gpmi-nand/gpmi-nand.c due to
added include files next to each other.
* tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd: (75 commits)
mtd: mxc_nand: move ecc strengh setup before nand_scan_tail
mtd: block2mtd: fix recursive call of mtd_writev
mtd: gpmi-nand: define ecc.strength
mtd: of_parts: fix breakage in Kconfig
mtd: nand: fix scan_read_raw_oob
mtd: docg3 fix in-middle of blocks reads
mtd: cfi_cmdset_0002: Slight cleanup of fixup messages
mtd: add fixup for S29NS512P NOR flash.
jffs2: allow to complete xattr integrity check on first GC scan
jffs2: allow to discriminate between recoverable and non-recoverable errors
mtd: nand: omap: add support for hardware BCH ecc
ARM: OMAP3: gpmc: add BCH ecc api and modes
mtd: nand: check the return code of 'read_oob/read_oob_raw'
mtd: nand: remove 'sndcmd' parameter of 'read_oob/read_oob_raw'
mtd: m25p80: Add support for Winbond W25Q80BW
jffs2: get rid of jffs2_sync_super
jffs2: remove unnecessary GC pass on sync
jffs2: remove unnecessary GC pass on umount
jffs2: remove lock_super
mtd: gpmi: add gpmi support for mx6q
...
