An endpoint conflict occurs when the USB is working in device mode
during an isochronous communication. When the endpointA IN direction
is an isochronous IN endpoint, and the host sends an IN token to
endpointA on another device, then the OUT transaction may be missed
regardless the OUT endpoint number. Generally, this occurs when the
device is connected to the host through a hub and other devices are
connected to the same hub.
The affected OUT endpoint can be either control, bulk, isochronous, or
an interrupt endpoint. After the OUT endpoint is primed, if an IN token
to the same endpoint number on another device is received, then the OUT
endpoint may be unprimed (cannot be detected by software), which causes
this endpoint to no longer respond to the host OUT token, and thus, no
corresponding interrupt occurs.
There is no good workaround for this issue, the only thing the software
could do is numbering isochronous IN from the highest endpoint since we
have observed most of device number endpoint from the lowest.
Cc: <stable@vger.kernel.org> #v3.14+
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch updates the Qualcomm SoC repo to a new location.
Signed-off-by: Andy Gross <agross@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
SDIO IRQ is triggered by low level. It need disable SDIO IRQ
detected function. Otherwise the interrupt register can't be cleared.
It will process the interrupt more.
Signed-off-by: Jjian Zhou <jjian.zhou@mediatek.com>
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Yong Mao <yong.mao@mediatek.com>
Fixes: 5215b2e952 ("mmc: mediatek: Add MMC_CAP_SDIO_IRQ support")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We don't have a reproducible error case, yet our BSP team suggested that
the mmc_switch_status() command in mmc_select_hs400() should come after
the callback into the driver completing HS400 setup. It makes sense to
me because we want the status of a fully setup HS400, so it will
increase the reliability of the mmc_switch_status() command.
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Fixes: ba6c7ac3a2 ("mmc: core: more fine-grained hooks for HS400 tuning")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Because RISC-V compliant implementations can cache invalid entries
in TLB, an SFENCE.VMA is necessary after changes to the page table.
This patch adds an SFENCE.vma for the vmalloc_fault path.
Signed-off-by: ShihPo Hung <shihpo.hung@sifive.com>
[paul.walmsley@sifive.com: reversed tab->whitespace conversion,
wrapped comment lines]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: linux-riscv@lists.infradead.org
Cc: stable@vger.kernel.org
My @arm.com address will stop working at the end of August, so update to
my @kernel.org address where you'll still be able to reach me.
When I say "stop working" I really mean "will go to my line manager", so
send patches there at your peril because they may reply with roadmaps
and spreadsheets. You have been warned.
Cc: Will Deacon <will@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: "Paul E . McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: arm-soc <arm@kernel.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Add initial board data for the SiFive HiFive Unleashed A00.
Currently the data populated in this DT file describes the board
DRAM configuration and the external clock sources that supply the
PRCI.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Loys Ollivier <lollivier@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Antony Pavlov <antonynpavlov@gmail.com>
Cc: devicetree@vger.kernel.org
Cc: linux-riscv@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Add initial support for the SiFive FU540-C000 SoC. This is a 28nm SoC
based around the SiFive U54-MC core complex and a TileLink
interconnect.
This file is expected to grow as more device drivers are added to the
kernel.
This patch includes a fix to the QSPI memory map due to a
documentation bug, found by ShihPo Hung <shihpo.hung@sifive.com>, adds
entries for the I2C controller, and merges all DT changes that
formerly were made dynamically by the riscv-pk BBL proxy kernel.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Loys Ollivier <lollivier@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: ShihPo Hung <shihpo.hung@sifive.com>
Cc: devicetree@vger.kernel.org
Cc: linux-riscv@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
At Rob's request, we're starting to migrate our DT binding
documentation to json-schema YAML format. Start by converting our cpu
binding documentation. While doing so, document more properties and
nodes. This includes adding binding documentation support for the E51
and U54 CPU cores ("harts") that are present on this SoC. These cores
are described in:
https://static.dev.sifive.com/FU540-C000-v1.0.pdf
This cpus.yaml file is intended to be a starting point and to
evolve over time. It passes dt-doc-validate as of the yaml-bindings
commit 4c79d42e9216.
This patch was originally based on the ARM json-schema binding
documentation as added by commit 672951cbd1 ("dt-bindings: arm: Convert
cpu binding to json-schema").
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-riscv@lists.infradead.org
Add YAML DT binding documentation for the SiFive FU540 SoC. This
SoC is documented at:
https://static.dev.sifive.com/FU540-C000-v1.0.pdf
Passes dt-doc-validate, as of yaml-bindings commit 4c79d42e9216.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: devicetree@vger.kernel.org
Cc: linux-riscv@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Similar to ARM64, add support for building DTB files from DT source
data for RISC-V boards.
This patch starts with the infrastructure needed for SiFive boards.
Boards from other vendors would add support here in a similar form.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Loys Ollivier <lollivier@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
There is pvinfo writing come from vgpu might be unexpected, like
writing to one unknown address, GVT-g should do as reserved register
to discard any invalid write. Now GVT-g lets it write to the vreg
without prompt error message, should ignore the unexpected pvinfo
write access and leave the vreg as the default value.
For possible guest query GVT-g host feature, this returned proper
value instead of wrong guest setting.
v2: ignore unexpected pvinfo write instead of return predefined value
Fixes: e39c5add32 ("drm/i915/gvt: vGPU MMIO virtualization")
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Weinan Li <weinan.z.li@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
lapb_register calls lapb_create_cb, which initializes the control-
block's ref-count to one, and __lapb_insert_cb, which increments it when
adding the new block to the list of blocks.
lapb_unregister calls __lapb_remove_cb, which decrements the ref-count
when removing control-block from the list of blocks, and calls lapb_put
itself to decrement the ref-count before returning.
However, lapb_unregister also calls __lapb_devtostruct to look up the
right control-block for the given net_device, and __lapb_devtostruct
also bumps the ref-count, which means that when lapb_unregister returns
the ref-count is still 1 and the control-block is leaked.
Call lapb_put after __lapb_devtostruct to fix leak.
Reported-by: syzbot+afb980676c836b4a0afa@syzkaller.appspotmail.com
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzbot reported a memleak caused by grp members' deferredq list not
purged when the grp is be deleted.
The issue occurs when more(msg_grp_bc_seqno(hdr), m->bc_rcv_nxt) in
tipc_group_filter_msg() and the skb will stay in deferredq.
So fix it by calling __skb_queue_purge for each member's deferredq
in tipc_group_delete() when a tipc sk leaves the grp.
Fixes: b87a5ea31c ("tipc: guarantee group unicast doesn't bypass group broadcast")
Reported-by: syzbot+78fbe679c8ca8d264a8d@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_tx_skb_cache_key and tcp_rx_skb_cache_key must be available
even if CONFIG_SYSCTL is not set.
Fixes: 0b7d7f6b22 ("tcp: add tcp_tx_skb_cache sysctl")
Fixes: ede61ca474 ("tcp: add tcp_rx_skb_cache sysctl")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc 8.2.0 may report these bogus warnings under some condition:
warning: ‘vnew’ may be used uninitialized in this function
warning: ‘hvs_new’ may be used uninitialized in this function
Actually, the 2 pointers are only initialized and used if the variable
"conn_from_host" is true. The code is not buggy here.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Number of Rx queues used for flow hashing returned by the driver is
incorrect and this bug prevents user to use the last Rx queue in
indirection table.
Let's say we have a NIC with 6 combined queues:
[root@sm-03 ~]# ethtool -l enp4s0f0
Channel parameters for enp4s0f0:
Pre-set maximums:
RX: 5
TX: 5
Other: 0
Combined: 6
Current hardware settings:
RX: 0
TX: 0
Other: 0
Combined: 6
Default indirection table maps all (6) queues equally but the driver
reports only 5 rings available.
[root@sm-03 ~]# ethtool -x enp4s0f0
RX flow hash indirection table for enp4s0f0 with 5 RX ring(s):
0: 0 1 2 3 4 5 0 1
8: 2 3 4 5 0 1 2 3
16: 4 5 0 1 2 3 4 5
24: 0 1 2 3 4 5 0 1
...
Now change indirection table somehow:
[root@sm-03 ~]# ethtool -X enp4s0f0 weight 1 1
[root@sm-03 ~]# ethtool -x enp4s0f0
RX flow hash indirection table for enp4s0f0 with 6 RX ring(s):
0: 0 0 0 0 0 0 0 0
...
64: 1 1 1 1 1 1 1 1
...
Now it is not possible to change mapping back to equal (default) state:
[root@sm-03 ~]# ethtool -X enp4s0f0 equal 6
Cannot set RX flow hash configuration: Invalid argument
Fixes: 594ad54a2c ("be2net: Add support for setting and getting rx flow hash options")
Reported-by: Tianhao <tizhao@redhat.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When stack receives pkt: [802.1P vlan 0][802.1AD vlan 100][IPv4],
vlan_do_receive() returns false if it does not find vlan_dev. Later
__netif_receive_skb_core() fails to find packet type handler for
skb->protocol 801.1AD and drops the packet.
801.1P header with vlan id 0 should be handled as untagged packets.
This patch fixes it by checking if vlan_id is 0 and processes next vlan
header.
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three fixes mostly for dra7 SoC variants that have some devices disabled
compared to the base SoC. These got broken by the change of making devices
probe with ti-sysc interconnect target module and went unnnoticed for a
while. And there is no clkcel bit for timer12 unlike timer1. Also included
is a GPIO direction fix for phytec SDIO card detection.
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEkgNvrZJU/QSQYIcQG9Q+yVyrpXMFAlz+CUURHHRvbnlAYXRv
bWlkZS5jb20ACgkQG9Q+yVyrpXN0fA/6Avr8yF2fN/EyHhab6dK5r6WkxCmk0Dpg
RnlunnQ+2dN5IDT5AbNpou/2kr/aEqnzQfzHez7eD7+JURllcpm7oUoiS6h6iWTK
Koyau7BtFA9Zy5R9vXjITaAseKTlD4l/KF8coMvSiZ2fa/ApuP33BW+2edwv27EF
jB44F01vGKkjpX8k3CsG2nrPzrhydLNAgEXHGTSXV9OU4nfgpE/LYhfTn7Cw63wr
tCcAJdTCF9envRGd+m6uYWKbsjYbWYCywS17RqsMBGdcWeoFXYRR00fJfZ2dhPFO
xEYhgNqyVU08VBASMOZTmMjUz5nlJPTPMISM9DPjD5XRmY9vby1kO1kZBOybKS4e
oHj26sWhCqCpA5jAq+I3LcFHIxJDNITg2u06u58SxbZHml3Y5wFUGn+gvcjB5xuW
k/ASGpawv3dA1MyfoCgZJrprdv0/YnFuVvW/TAa13cW/AUWseRyJcJlI6BI0cBPN
GH/wTQkKERNo+ugclbGNlz27VELoL4lsiSJALp8UOLEOg80nxoXLMlwVs9lqCW0w
Invewxaz00iDa0hjpdvuFiqwE67bC4I0wtS69NgR8BL+84UZmVj1oCdFA2njyell
TPj15GJK4ofND2r4FvFY7lnpVOvt3EpaiQ1Cmvn5YXXsTovQ7OiOQkLbnTs/hTFI
ekUIQgEuMq4=
=g05K
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.2/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omap variants
Three fixes mostly for dra7 SoC variants that have some devices disabled
compared to the base SoC. These got broken by the change of making devices
probe with ti-sysc interconnect target module and went unnnoticed for a
while. And there is no clkcel bit for timer12 unlike timer1. Also included
is a GPIO direction fix for phytec SDIO card detection.
* tag 'omap-for-v5.2/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x phytec boards: Fix cd-gpios active level
ARM: dts: dra72x: Disable usb4_tm target module
ARM: dts: Drop bogus CLKSEL for timer12 on dra7
Signed-off-by: Olof Johansson <olof@lixom.net>
This addresses an issue with probe of IO expander on DA850 EVM. There is
also a WARN_ON() fix on DA850 and DA830 devices.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=1gFV
-----END PGP SIGNATURE-----
Merge tag 'davinci-fixes-for-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into fixes
DaVinci fixes for v5.2 kernel.
This addresses an issue with probe of IO expander on DA850 EVM. There is
also a WARN_ON() fix on DA850 and DA830 devices.
* tag 'davinci-fixes-for-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: da8xx: specify dma_coherent_mask for lcdc
ARM: davinci: da850-evm: call regulator_has_full_constraints()
Signed-off-by: Olof Johansson <olof@lixom.net>
Fixing defconfig allowing to use Ethernet again on Armada 38x based
boards
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCXQNQDAAKCRALBhiOFHI7
1dqXAJ9ght2djbWrvtPLbfr10y7kkYFQHgCfbupD05I+H4+aGx7pnIvdvZ21qYU=
=SU1/
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-5.2-1' of git://git.infradead.org/linux-mvebu into fixes
mvebu fixes for 5.2 (part 1)
Fixing defconfig allowing to use Ethernet again on Armada 38x based
boards
* tag 'mvebu-fixes-5.2-1' of git://git.infradead.org/linux-mvebu:
ARM: mvebu_v7_defconfig: fix Ethernet on Clearfog
Signed-off-by: Olof Johansson <olof@lixom.net>
- Fix up a Kbuild warning when SOC_TI is not set
-----BEGIN PGP SIGNATURE-----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=Guww
-----END PGP SIGNATURE-----
Merge tag 'am654-fixes-for-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/kristo/linux into fixes
Texas Instruments AM65x fixes for v5.2
- Fix up a Kbuild warning when SOC_TI is not set
* tag 'am654-fixes-for-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/kristo/linux:
arm64: arch_k3: Fix kconfig dependency warning
Signed-off-by: Olof Johansson <olof@lixom.net>
5.2-rc1, please pull the following:
- Florian fixes the remaining Broadcom DTS files to have a valid
device_type = "memory" property which was missed during the removal of
skeleton.dtsi
-----BEGIN PGP SIGNATURE-----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=rECv
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.2/devicetree-fixes' of https://github.com/Broadcom/stblinux into fixes
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for
5.2-rc1, please pull the following:
- Florian fixes the remaining Broadcom DTS files to have a valid
device_type = "memory" property which was missed during the removal of
skeleton.dtsi
* tag 'arm-soc/for-5.2/devicetree-fixes' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm: Add missing device_type = "memory" property
Signed-off-by: Olof Johansson <olof@lixom.net>
This series contains dra7 mmc voltage fixes, and fixes to the recent
changes to probe devices with device tree data insteas of legacy
platform data:
- Two fixes for dra7 mmc that needs 1.8V mode disabled as in case of a
reset, the bootrom will try to access the mmc card at 3.3V potentially
damaging the card
- Two regression fixes for am335x d_can. We must allow devices with no
control registers for ti-sysc interconnect target module driver for
at least d_can, and we remove the incorrect control registers for
d_can. And we must configure the osc clock for d_can as otherwise
register access may fail depending on the bootloader version
- Four regression fixes for dra7 variant dts files to tag rtc and usb4
as disabled for dra71x and dra76x. These SoC variants do not have
these devices, and got accidentally enabled when the L4 interconnect
got defined in the dra7-l4.dtsi for the dra7 SoC family
-----BEGIN PGP SIGNATURE-----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=Ajjk
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.2/fixes-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omap variants for dra7 mmc voltage and boot issues
This series contains dra7 mmc voltage fixes, and fixes to the recent
changes to probe devices with device tree data insteas of legacy
platform data:
- Two fixes for dra7 mmc that needs 1.8V mode disabled as in case of a
reset, the bootrom will try to access the mmc card at 3.3V potentially
damaging the card
- Two regression fixes for am335x d_can. We must allow devices with no
control registers for ti-sysc interconnect target module driver for
at least d_can, and we remove the incorrect control registers for
d_can. And we must configure the osc clock for d_can as otherwise
register access may fail depending on the bootloader version
- Four regression fixes for dra7 variant dts files to tag rtc and usb4
as disabled for dra71x and dra76x. These SoC variants do not have
these devices, and got accidentally enabled when the L4 interconnect
got defined in the dra7-l4.dtsi for the dra7 SoC family
* tag 'omap-for-v5.2/fixes-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: dra71x: Disable usb4_tm target module
ARM: dts: dra71x: Disable rtc target module
ARM: dts: dra76x: Disable usb4_tm target module
ARM: dts: dra76x: Disable rtc target module
ARM: dts: dra76x: Update MMC2_HS200_MANUAL1 iodelay values
ARM: dts: am57xx-idk: Remove support for voltage switching for SD card
bus: ti-sysc: Handle devices with no control registers
ARM: dts: Configure osc clock for d_can on am335x
Signed-off-by: Olof Johansson <olof@lixom.net>
- A build fix for soc-imx8 driver which needs SOC_BUS support. To
avoid dealing with the dependency for every single i.MX SoC bus
driver, we selects at from architecture level.
- A fix on i.MX SCU firmware driver to ensure SCU irq is enabled only
after IPC is ready.
- A regression fix on cpuidle-imx6sx driver, which causes some
characters loss on serial communication.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJc50FAAAoJEFBXWFqHsHzOt4wIAJJ4MLXCMKj2oVWXimkF3DAF
g9M7ridrarhPAXowuTYV4FuW7me7nPxr5VTmwVIJE23wEKdaOd7cg0tkmvMi0tG6
3TlNwCsEjJx+9rtGF196SZfR9HinLziAc4x7Qcl88xlQTQEIptvx6AMPit7Gy0je
MJ0PzLA1l+tazo7dXvMjZ+LkxlvLTSB/RuBciA8sgOvwsdbG1Azz/AduSLxO7e/T
ZSmEElTluqIKVxH5sbVY0T7mxWat7l5As28nx27cWDHGPoDMOt/TWiCTAvFR0d6T
m+bW6xcvy63Z2II1Er//ig4rwcmK1mcUv+3i63/sIkFxl9fa0H4WnTu67T+/mck=
=zbC7
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 5.2:
- A build fix for soc-imx8 driver which needs SOC_BUS support. To
avoid dealing with the dependency for every single i.MX SoC bus
driver, we selects at from architecture level.
- A fix on i.MX SCU firmware driver to ensure SCU irq is enabled only
after IPC is ready.
- A regression fix on cpuidle-imx6sx driver, which causes some
characters loss on serial communication.
* tag 'imx-fixes-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx: cpuidle-imx6sx: Restrict the SW2ISO increase to i.MX6SX
firmware: imx: SCU irq should ONLY be enabled after SCU IPC is ready
arm64: imx: Fix build error without CONFIG_SOC_BUS
Signed-off-by: Olof Johansson <olof@lixom.net>
ARM/ARM64 SoCs, please pull the following:
- Stefan updates his email address under the BCM2835 entry
-----BEGIN PGP SIGNATURE-----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=L52t
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.2/maintainers' of https://github.com/Broadcom/stblinux into fixes
This pull request contains MAINTAINERS file update for Broadcom
ARM/ARM64 SoCs, please pull the following:
- Stefan updates his email address under the BCM2835 entry
* tag 'arm-soc/for-5.2/maintainers' of https://github.com/Broadcom/stblinux:
MAINTAINERS: Update Stefan Wahren email address
Signed-off-by: Olof Johansson <olof@lixom.net>
fixes for 5.2-rc1, please pull the following:
- Florian fixes the biuctrl driver not to create an error condition/path
upon unsupported CPU and also fixes the biuctrl driver writes to used
a data barrier which is necessary given the HW block design
-----BEGIN PGP SIGNATURE-----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=VOdD
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.2/drivers-fixes' of https://github.com/Broadcom/stblinux into fixes
This pull request contains Broadcom ARM/ARM64/MIPS SoCs device drivers
fixes for 5.2-rc1, please pull the following:
- Florian fixes the biuctrl driver not to create an error condition/path
upon unsupported CPU and also fixes the biuctrl driver writes to used
a data barrier which is necessary given the HW block design
* tag 'arm-soc/for-5.2/drivers-fixes' of https://github.com/Broadcom/stblinux:
soc: bcm: brcmstb: biuctrl: Register writes require a barrier
soc: brcmstb: Fix error path for unsupported CPUs
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull x86 fixes from Thomas Gleixner:
"The accumulated fixes from this and last week:
- Fix vmalloc TLB flush and map range calculations which lead to
stale TLBs, spurious faults and other hard to diagnose issues.
- Use fault_in_pages_writable() for prefaulting the user stack in the
FPU code as it's less fragile than the current solution
- Use the PF_KTHREAD flag when checking for a kernel thread instead
of current->mm as the latter can give the wrong answer due to
use_mm()
- Compute the vmemmap size correctly for KASLR and 5-Level paging.
Otherwise this can end up with a way too small vmemmap area.
- Make KASAN and 5-level paging work again by making sure that all
invalid bits are masked out when computing the P4D offset. This
worked before but got broken recently when the LDT remap area was
moved.
- Prevent a NULL pointer dereference in the resource control code
which can be triggered with certain mount options when the
requested resource is not available.
- Enforce ordering of microcode loading vs. perf initialization on
secondary CPUs. Otherwise perf tries to access a non-existing MSR
as the boot CPU marked it as available.
- Don't stop the resource control group walk early otherwise the
control bitmaps are not updated correctly and become inconsistent.
- Unbreak kgdb by returning 0 on success from
kgdb_arch_set_breakpoint() instead of an error code.
- Add more Icelake CPU model defines so depending changes can be
queued in other trees"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/microcode, cpuhotplug: Add a microcode loader CPU hotplug callback
x86/kasan: Fix boot with 5-level paging and KASAN
x86/fpu: Don't use current->mm to check for a kthread
x86/kgdb: Return 0 from kgdb_arch_set_breakpoint()
x86/resctrl: Prevent NULL pointer dereference when local MBM is disabled
x86/resctrl: Don't stop walking closids when a locksetup group is found
x86/fpu: Update kernel's FPU state before using for the fsave header
x86/mm/KASLR: Compute the size of the vmemmap section properly
x86/fpu: Use fault_in_pages_writeable() for pre-faulting
x86/CPU: Add more Icelake model numbers
mm/vmalloc: Avoid rare case of flushing TLB with weird arguments
mm/vmalloc: Fix calculation of direct map addr range
Pull timer fixes from Thomas Gleixner:
"A set of small fixes:
- Repair the ktime_get_coarse() functions so they actually deliver
what they are supposed to: tick granular time stamps. The current
code missed to add the accumulated nanoseconds part of the
timekeeper so the resulting granularity was 1 second.
- Prevent the tracer from infinitely recursing into time getter
functions in the arm architectured timer by marking these functions
notrace
- Fix a trivial compiler warning caused by wrong qualifier ordering"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timekeeping: Repair ktime_get_coarse*() granularity
clocksource/drivers/arm_arch_timer: Don't trace count reader functions
clocksource/drivers/timer-ti-dm: Change to new style declaration
Pull RAS fixes from Thomas Gleixner:
"Two small fixes for RAS:
- Use a proper search algorithm to find the correct element in the
CEC array. The replacement was a better choice than fixing the
crash causes by the original search function with horrible duct
tape.
- Move the timer based decay function into thread context so it can
actually acquire the mutex which protects the CEC array to prevent
corruption"
* 'ras-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
RAS/CEC: Convert the timer callback to a workqueue
RAS/CEC: Fix binary search function
If mtu probing is enabled tcp_mtu_probing() could very well end up
with a too small MSS.
Use the new sysctl tcp_min_snd_mss to make sure MSS search
is performed in an acceptable range.
CVE-2019-11479 -- tcp mss hardcoded to 48
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Cc: Jonathan Looney <jtl@netflix.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Tyler Hicks <tyhicks@canonical.com>
Cc: Bruce Curtis <brucec@netflix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some TCP peers announce a very small MSS option in their SYN and/or
SYN/ACK messages.
This forces the stack to send packets with a very high network/cpu
overhead.
Linux has enforced a minimal value of 48. Since this value includes
the size of TCP options, and that the options can consume up to 40
bytes, this means that each segment can include only 8 bytes of payload.
In some cases, it can be useful to increase the minimal value
to a saner value.
We still let the default to 48 (TCP_MIN_SND_MSS), for compatibility
reasons.
Note that TCP_MAXSEG socket option enforces a minimal value
of (TCP_MIN_MSS). David Miller increased this minimal value
in commit c39508d6f1 ("tcp: Make TCP_MAXSEG minimum more correct.")
from 64 to 88.
We might in the future merge TCP_MIN_SND_MSS and TCP_MIN_MSS.
CVE-2019-11479 -- tcp mss hardcoded to 48
Signed-off-by: Eric Dumazet <edumazet@google.com>
Suggested-by: Jonathan Looney <jtl@netflix.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Tyler Hicks <tyhicks@canonical.com>
Cc: Bruce Curtis <brucec@netflix.com>
Cc: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jonathan Looney reported that a malicious peer can force a sender
to fragment its retransmit queue into tiny skbs, inflating memory
usage and/or overflow 32bit counters.
TCP allows an application to queue up to sk_sndbuf bytes,
so we need to give some allowance for non malicious splitting
of retransmit queue.
A new SNMP counter is added to monitor how many times TCP
did not allow to split an skb if the allowance was exceeded.
Note that this counter might increase in the case applications
use SO_SNDBUF socket option to lower sk_sndbuf.
CVE-2019-11478 : tcp_fragment, prevent fragmenting a packet when the
socket is already using more than half the allowed space
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jonathan Looney <jtl@netflix.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Tyler Hicks <tyhicks@canonical.com>
Cc: Bruce Curtis <brucec@netflix.com>
Cc: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jonathan Looney reported that TCP can trigger the following crash
in tcp_shifted_skb() :
BUG_ON(tcp_skb_pcount(skb) < pcount);
This can happen if the remote peer has advertized the smallest
MSS that linux TCP accepts : 48
An skb can hold 17 fragments, and each fragment can hold 32KB
on x86, or 64KB on PowerPC.
This means that the 16bit witdh of TCP_SKB_CB(skb)->tcp_gso_segs
can overflow.
Note that tcp_sendmsg() builds skbs with less than 64KB
of payload, so this problem needs SACK to be enabled.
SACK blocks allow TCP to coalesce multiple skbs in the retransmit
queue, thus filling the 17 fragments to maximal capacity.
CVE-2019-11477 -- u16 overflow of TCP_SKB_CB(skb)->tcp_gso_segs
Fixes: 832d11c5cd ("tcp: Try to restore large SKBs while SACK processing")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jonathan Looney <jtl@netflix.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Tyler Hicks <tyhicks@canonical.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Bruce Curtis <brucec@netflix.com>
Cc: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf 2019-06-15
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) fix stack layout of JITed x64 bpf code, from Alexei.
2) fix out of bounds memory access in bpf_sk_storage, from Arthur.
3) fix lpm trie walk, from Jonathan.
4) fix nested bpf_perf_event_output, from Matt.
5) and several other fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit ef7bfa8472.
Russell King espressed some strong opposition to this
change, explaining that this is trying to make phylink
behave outside of how it has been designed.
Signed-off-by: David S. Miller <davem@davemloft.net>
BPF_PROG_TYPE_RAW_TRACEPOINTs can be executed nested on the same CPU, as
they do not increment bpf_prog_active while executing.
This enables three levels of nesting, to support
- a kprobe or raw tp or perf event,
- another one of the above that irq context happens to call, and
- another one in nmi context
(at most one of which may be a kprobe or perf event).
Fixes: 20b9d7ac48 ("bpf: avoid excessive stack usage for perf_sample_data")
Signed-off-by: Matt Mullins <mmullins@fb.com>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
bpf_sk_storage maps use multiple spin locks to reduce contention.
The number of locks to use is determined by the number of possible CPUs.
With only 1 possible CPU, bucket_log == 0, and 2^0 = 1 locks are used.
When updating elements, the correct lock is determined with hash_ptr().
Calling hash_ptr() with 0 bits is undefined behavior, as it does:
x >> (64 - bits)
Using the value results in an out of bounds memory access.
In my case, this manifested itself as a page fault when raw_spin_lock_bh()
is called later, when running the self tests:
./tools/testing/selftests/bpf/test_verifier 773 775
[ 16.366342] BUG: unable to handle page fault for address: ffff8fe7a66f93f8
Force the minimum number of locks to two.
Signed-off-by: Arthur Fabre <afabre@cloudflare.com>
Fixes: 6ac99e8f23 ("bpf: Introduce bpf sk local storage")
Acked-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Set the SOCK_DONE flag to match the TCP_CLOSING state when a peer has
shut down and there is nothing left to read.
This fixes the following bug:
1) Peer sends SHUTDOWN(RDWR).
2) Socket enters TCP_CLOSING but SOCK_DONE is not set.
3) read() returns -ENOTCONN until close() is called, then returns 0.
Signed-off-by: Stephen Barber <smbarber@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We get this regression when using RTL8366RB as part of a bridge
with OpenWrt:
WARNING: CPU: 0 PID: 1347 at net/switchdev/switchdev.c:291
switchdev_port_attr_set_now+0x80/0xa4
lan0: Commit of attribute (id=7) failed.
(...)
realtek-smi switch lan0: failed to initialize vlan filtering on this port
This is because it is trying to disable VLAN filtering
on VLAN0, as we have forgot to add 1 to the port number
to get the right VLAN in rtl8366_vlan_filtering(): when
we initialize the VLAN we associate VLAN1 with port 0,
VLAN2 with port 1 etc, so we need to add 1 to the port
offset.
Fixes: d8652956cf ("net: dsa: realtek-smi: Add Realtek SMI driver")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy_state field of phylink should carry only valid information
especially when this can be passed to the .mac_config callback.
Update the an_enabled field with the autoneg state in the
phylink_phy_change function.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Couple of driver enumeration issues have been fixed for Mellanox.
ASUS laptops got a regression with backlight, which is fixed now.
Dell computers got a wrong mode (tablet versus laptop) after resume,
that is fixed now.
The following is an automated git shortlog grouped by driver:
asus-wmi:
- Only Tell EC the OS will handle display hotkeys from asus_nb_wmi
intel-vbtn:
- Report switch events when event wakes device
mlx-platform:
- Fix parent device in i2c-mux-reg device registration
platform/mellanox:
- mlxreg-hotplug: Add devm_free_irq call to remove flow
-----BEGIN PGP SIGNATURE-----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=/H6h
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v5.2-3' of git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver fixes from Andy Shevchenko:
- fix a couple of Mellanox driver enumeration issues
- fix ASUS laptop regression with backlight
- fix Dell computers that got a wrong mode (tablet versus laptop) after
resume
* tag 'platform-drivers-x86-v5.2-3' of git://git.infradead.org/linux-platform-drivers-x86:
platform/mellanox: mlxreg-hotplug: Add devm_free_irq call to remove flow
platform/x86: mlx-platform: Fix parent device in i2c-mux-reg device registration
platform/x86: intel-vbtn: Report switch events when event wakes device
platform/x86: asus-wmi: Only Tell EC the OS will handle display hotkeys from asus_nb_wmi
Here are some small USB driver fixes for 5.2-rc5
Nothing major, just some small gadget fixes, usb-serial new device ids,
a few new quirks, and some small fixes for some regressions that have
been found after the big 5.2-rc1 merge.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXQUTIg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykPJQCfZdiElw3N35bKVf7bhruxSb5DevEAni96uDM7
jSOSEB/EWqxZEy0ZjU7J
=cKx4
-----END PGP SIGNATURE-----
Merge tag 'usb-5.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB driver fixes for 5.2-rc5
Nothing major, just some small gadget fixes, usb-serial new device
ids, a few new quirks, and some small fixes for some regressions that
have been found after the big 5.2-rc1 merge.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: typec: Make sure an alt mode exist before getting its partner
usb: gadget: udc: lpc32xx: fix return value check in lpc32xx_udc_probe()
usb: gadget: dwc2: fix zlp handling
usb: dwc2: Set actual frame number for completed ISOC transfer for none DDMA
usb: gadget: udc: lpc32xx: allocate descriptor with GFP_ATOMIC
usb: gadget: fusb300_udc: Fix memory leak of fusb300->ep[i]
usb: phy: mxs: Disable external charger detect in mxs_phy_hw_init()
usb: dwc2: Fix DMA cache alignment issues
usb: dwc2: host: Fix wMaxPacketSize handling (fix webcam regression)
USB: Fix chipmunk-like voice when using Logitech C270 for recording audio.
USB: usb-storage: Add new ID to ums-realtek
usb: typec: ucsi: ccg: fix memory leak in do_flash
USB: serial: option: add Telit 0x1260 and 0x1261 compositions
USB: serial: pl2303: add Allied Telesis VT-Kit3
USB: serial: option: add support for Simcom SIM7500/SIM7600 RNDIS mode
One fix for a regression introduced by our 32-bit KASAN support, which broke
booting on machines with "bootx" early debugging enabled.
A fix for a bug which broke kexec on 32-bit, introduced by changes to the 32-bit
STRICT_KERNEL_RWX support in v5.1.
Finally two fixes going to stable for our THP split/collapse handling,
discovered by Nick. The first fixes random crashes and/or corruption in guests
under sufficient load.
Thanks to:
Nicholas Piggin, Christophe Leroy, Aaro Koskinen, Mathieu Malaterre.
-----BEGIN PGP SIGNATURE-----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=MXJI
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.2-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"One fix for a regression introduced by our 32-bit KASAN support, which
broke booting on machines with "bootx" early debugging enabled.
A fix for a bug which broke kexec on 32-bit, introduced by changes to
the 32-bit STRICT_KERNEL_RWX support in v5.1.
Finally two fixes going to stable for our THP split/collapse handling,
discovered by Nick. The first fixes random crashes and/or corruption
in guests under sufficient load.
Thanks to: Nicholas Piggin, Christophe Leroy, Aaro Koskinen, Mathieu
Malaterre"
* tag 'powerpc-5.2-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/32s: fix booting with CONFIG_PPC_EARLY_DEBUG_BOOTX
powerpc/64s: __find_linux_pte() synchronization vs pmdp_invalidate()
powerpc/64s: Fix THP PMD collapse serialisation
powerpc: Fix kexec failure on book3s/32
- Out of range read of stack trace output
- Fix for NULL pointer dereference in trace_uprobe_create()
- Fix to a livepatching / ftrace permission race in the module code
- Fix for NULL pointer dereference in free_ftrace_func_mapper()
- A couple of build warning clean ups
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCXQToxhQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qusmAP4/mmJPgsDchnu5ui0wB8BByzJlsPn8
luXFDuqI4f34zgD+JCmeYbj5LLh98D9XkaaEgP4yz3yKsWeSdwWPCU0vTgo=
=M/+E
-----END PGP SIGNATURE-----
Merge tag 'trace-v5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
- Out of range read of stack trace output
- Fix for NULL pointer dereference in trace_uprobe_create()
- Fix to a livepatching / ftrace permission race in the module code
- Fix for NULL pointer dereference in free_ftrace_func_mapper()
- A couple of build warning clean ups
* tag 'trace-v5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace: Fix NULL pointer dereference in free_ftrace_func_mapper()
module: Fix livepatch/ftrace module text permissions race
tracing/uprobe: Fix obsolete comment on trace_uprobe_create()
tracing/uprobe: Fix NULL pointer dereference in trace_uprobe_create()
tracing: Make two symbols static
tracing: avoid build warning with HAVE_NOP_MCOUNT
tracing: Fix out-of-range read in trace_stack_print()
Adric Blake reported the following warning during suspend-resume:
Enabling non-boot CPUs ...
x86: Booting SMP configuration:
smpboot: Booting Node 0 Processor 1 APIC 0x2
unchecked MSR access error: WRMSR to 0x10f (tried to write 0x0000000000000000) \
at rIP: 0xffffffff8d267924 (native_write_msr+0x4/0x20)
Call Trace:
intel_set_tfa
intel_pmu_cpu_starting
? x86_pmu_dead_cpu
x86_pmu_starting_cpu
cpuhp_invoke_callback
? _raw_spin_lock_irqsave
notify_cpu_starting
start_secondary
secondary_startup_64
microcode: sig=0x806ea, pf=0x80, revision=0x96
microcode: updated to revision 0xb4, date = 2019-04-01
CPU1 is up
The MSR in question is MSR_TFA_RTM_FORCE_ABORT and that MSR is emulated
by microcode. The log above shows that the microcode loader callback
happens after the PMU restoration, leading to the conjecture that
because the microcode hasn't been updated yet, that MSR is not present
yet, leading to the #GP.
Add a microcode loader-specific hotplug vector which comes before
the PERF vectors and thus executes earlier and makes sure the MSR is
present.
Fixes: 400816f60c ("perf/x86/intel: Implement support for TSX Force Abort")
Reported-by: Adric Blake <promarbler14@gmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Cc: x86@kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203637
