Setting the numa_preferred_node for a task in task_numa_migrate
does nothing on a 2-node system. Either we migrate to the node
that already was our preferred node, or we stay where we were.
On a 4-node system, it can slightly decrease overhead, by not
calling the NUMA code as much. Since every node tends to be
directly connected to every other node, running on the wrong
node for a while does not do much damage.
However, on an 8 node system, there are far more bad nodes
than there are good ones, and pretending that a second choice
is actually the preferred node can greatly delay, or even
prevent, a workload from converging.
The only time we can safely pretend that a second choice
node is the preferred node is when the task is part of a
workload that spans multiple NUMA nodes.
Signed-off-by: Rik van Riel <riel@redhat.com>
Tested-by: Vinod Chegu <chegu_vinod@hp.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1397235629-16328-4-git-send-email-riel@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When tasks have not converged on their preferred nodes yet, we want
to retry fairly often, to make sure we do not migrate a task's memory
to an undesirable location, only to have to move it again later.
This patch reduces the interval at which migration is retried,
when the task's numa_scan_period is small.
Signed-off-by: Rik van Riel <riel@redhat.com>
Tested-by: Vinod Chegu <chegu_vinod@hp.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1397235629-16328-3-git-send-email-riel@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The NUMA code is smart enough to distribute the memory of workloads
that span multiple NUMA nodes across those NUMA nodes.
However, it still has a pretty high scan rate for such workloads,
because any memory that is left on a node other than the node of
the CPU that faulted on the memory is counted as non-local, which
causes the scan rate to go up.
Counting the memory on any node where the task's numa group is
actively running as local, allows the scan rate to slow down
once the application is settled in.
This should reduce the overhead of the automatic NUMA placement
code, when a workload spans multiple NUMA nodes.
Signed-off-by: Rik van Riel <riel@redhat.com>
Tested-by: Vinod Chegu <chegu_vinod@hp.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1397235629-16328-2-git-send-email-riel@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The following commit:
e5fc66119e ("sched: Fix race in idle_balance()")
can potentially cause rq->max_idle_balance_cost to not be updated,
even when load_balance(NEWLY_IDLE) is attempted and the per-sd
max cost value is updated.
Preeti noticed a similar issue with updating rq->next_balance.
In this patch, we fix this by making sure we still check/update those values
even if a task gets enqueued while browsing the domains.
Signed-off-by: Jason Low <jason.low2@hp.com>
Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: morten.rasmussen@arm.com
Cc: aswin@hp.com
Cc: daniel.lezcano@linaro.org
Cc: alex.shi@linaro.org
Cc: efault@gmx.de
Cc: vincent.guittot@linaro.org
Link: http://lkml.kernel.org/r/1398725155-7591-2-git-send-email-jason.low2@hp.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tim wrote:
"The current code will call pick_next_task_fair a second time in the
slow path if we did not pull any task in our first try. This is
really unnecessary as we already know no task can be pulled and it
doubles the delay for the cpu to enter idle.
We instrumented some network workloads and that saw that
pick_next_task_fair is frequently called twice before a cpu enters
idle. The call to pick_next_task_fair can add non trivial latency as
it calls load_balance which runs find_busiest_group on an hierarchy of
sched domains spanning the cpus for a large system. For some 4 socket
systems, we saw almost 0.25 msec spent per call of pick_next_task_fair
before a cpu can be idled."
Optimize the second call away for the common case and document the
dependency.
Reported-by: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Len Brown <len.brown@intel.com>
Link: http://lkml.kernel.org/r/20140424100047.GP11096@twins.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The check at the beginning of cpupri_find() makes sure that the task_pri
variable does not exceed the cp->pri_to_cpu array length. But that length
is CPUPRI_NR_PRIORITIES not MAX_RT_PRIO, where it will miss the last two
priorities in that array.
As task_pri is computed from convert_prio() which should never be bigger
than CPUPRI_NR_PRIORITIES, if the check should cause a panic if it is
hit.
Reported-by: Mike Galbraith <umgwanakikbuti@gmail.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1397015410.5212.13.camel@marge.simpson.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
yield_task_dl() is broken:
o it forces current to be throttled setting its runtime to zero;
o it sets current's dl_se->dl_new to one, expecting that dl_task_timer()
will queue it back with proper parameters at replenish time.
Unfortunately, dl_task_timer() has this check at the very beginning:
if (!dl_task(p) || dl_se->dl_new)
goto unlock;
So, it just bails out and the task is never replenished. It actually
yielded forever.
To fix this, introduce a new flag indicating that the task properly yielded
the CPU before its current runtime expired. While this is a little overdoing
at the moment, the flag would be useful in the future to discriminate between
"good" jobs (of which remaining runtime could be reclaimed, i.e. recycled)
and "bad" jobs (for which dl_throttled task has been set) that needed to be
stopped.
Reported-by: yjay.kim <yjay.kim@lge.com>
Signed-off-by: Juri Lelli <juri.lelli@gmail.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20140429103953.e68eba1b2ac3309214e3dc5a@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Russell reported, that irqtime_account_idle_ticks() takes ages due to:
for (i = 0; i < ticks; i++)
irqtime_account_process_tick(current, 0, rq);
It's sad, that this code was written way _AFTER_ the NOHZ idle
functionality was available. I charge myself guitly for not paying
attention when that crap got merged with commit abb74cefa ("sched:
Export ns irqtimes through /proc/stat")
So instead of looping nr_ticks times just apply the whole thing at
once.
As a side note: The whole cputime_t vs. u64 business in that context
wants to be cleaned up as well. There is no point in having all these
back and forth conversions. Lets standardise on u64 nsec for all
kernel internal accounting and be done with it. Everything else does
not make sense at all for fine grained accounting. Frederic, can you
please take care of that?
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Venkatesh Pallipadi <venki@google.com>
Cc: Shaun Ruffell <sruffell@digium.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/alpine.DEB.2.02.1405022307000.6261@ionos.tec.linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When 'flags' argument to sched_{set,get}attr() syscalls were
added in:
6d35ab4809 ("sched: Add 'flags' argument to sched_{set,get}attr() syscalls")
no description for 'flags' was added. It causes the following warnings on "make htmldocs":
Warning(/kernel/sched/core.c:3645): No description found for parameter 'flags'
Warning(/kernel/sched/core.c:3789): No description found for parameter 'flags'
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Cc: peterz@infradead.org
Link: http://lkml.kernel.org/r/1397753955-2914-1-git-send-email-standby24x7@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull more networking fixes from David Miller:
1) Fix mlx4_en_netpoll implementation, it needs to schedule a NAPI
context, not synchronize it. From Chris Mason.
2) Ipv4 flow input interface should never be zero, it should be
LOOPBACK_IFINDEX instead. From Cong Wang and Julian Anastasov.
3) Properly configure MAC to PHY connection in mvneta devices, from
Thomas Petazzoni.
4) sys_recv should use SYSCALL_DEFINE. From Jan Glauber.
5) Tunnel driver ioctls do not use the correct namespace, fix from
Nicolas Dichtel.
6) Fix memory leak on seccomp filter attach, from Kees Cook.
7) Fix lockdep warning for nested vlans, from Ding Tianhong.
8) Crashes can happen in SCTP due to how the auth_enable value is
managed, fix from Vlad Yasevich.
9) Wireless fixes from John W Linville and co.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (45 commits)
net: sctp: cache auth_enable per endpoint
tg3: update rx_jumbo_pending ring param only when jumbo frames are enabled
vlan: Fix lockdep warning when vlan dev handle notification
seccomp: fix memory leak on filter attach
isdn: icn: buffer overflow in icn_command()
ip6_tunnel: use the right netns in ioctl handler
sit: use the right netns in ioctl handler
ip_tunnel: use the right netns in ioctl handler
net: use SYSCALL_DEFINEx for sys_recv
net: mdio-gpio: Add support for separate MDI and MDO gpio pins
net: mdio-gpio: Add support for active low gpio pins
net: mdio-gpio: Use devm_ functions where possible
ipv4, route: pass 0 instead of LOOPBACK_IFINDEX to fib_validate_source()
ipv4, fib: pass LOOPBACK_IFINDEX instead of 0 to flowi4_iif
mlx4_en: don't use napi_synchronize inside mlx4_en_netpoll
net: mvneta: properly configure the MAC <-> PHY connection in all situations
net: phy: add minimal support for QSGMII PHY
sfc:On MCDI timeout, issue an FLR (and mark MCDI to fail-fast)
mwifiex: fix hung task on command timeout
mwifiex: process event before command response
...
Fix:
BUG: using __this_cpu_write() in preemptible [00000000] code: systemd-udevd/497
caller is __this_cpu_preempt_check+0x13/0x20
CPU: 3 PID: 497 Comm: systemd-udevd Tainted: G W 3.15.0-rc1 #9
Hardware name: Hewlett-Packard HP EliteBook 8470p/179B, BIOS 68ICF Ver. F.02 04/27/2012
Call Trace:
check_preemption_disabled+0xe1/0xf0
__this_cpu_preempt_check+0x13/0x20
touch_nmi_watchdog+0x28/0x40
Reported-by: Luis Henriques <luis.henriques@canonical.com>
Tested-by: Luis Henriques <luis.henriques@canonical.com>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Cc: Robert Moore <robert.moore@intel.com>
Cc: Lv Zheng <lv.zheng@intel.com>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Christoph Lameter <cl@linux.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The first is to remove a duplication of creating debugfs files that
already exist and causes an error report to be printed due to the
failure of the second creation.
The second is a memory leak fix that was introduced in 3.14.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTUGZwAAoJEKQekfcNnQGu7W8IAIAMBVfrWdP6cmGle4tGfhVE
sHcwqTH+07oANQJ3eFwFs5wBMb08s3hXwUHUxXcpjyq2Bs+AHr0vSL/nqCG4k8Ap
2T4ntL7esC1BWKw2lVVVYD12FiL7grUXVlx/q0WE2NuhCzWzNRTyb8sKrPoCRUEB
3o5rAt9+45PKUb2k/eqGBGhK8b4XDz2Wtk5Gj6YB3xttse/yjjcuw0gWMHN1JWfm
eRuQUUBDDGUGkfF98k1aLrjPZooT3LIAV8L8md5C3ebEcXSC/h86hTYCGXv3oBDO
8sxcT0zoQcLuFhjkYLL1J1lBW6gxaVh052jYmQwMppQMos+WID2un2E92Ccg49E=
=BwLF
-----END PGP SIGNATURE-----
Merge tag 'trace-fixes-v3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"This contains two fixes.
The first is to remove a duplication of creating debugfs files that
already exist and causes an error report to be printed due to the
failure of the second creation.
The second is a memory leak fix that was introduced in 3.14"
* tag 'trace-fixes-v3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing/uprobes: Fix uprobe_cpu_buffer memory leak
tracing: Do not try to recreated toplevel set_ftrace_* files
This reverts commit 4c6c4e38c4 ("sched/core: Fix endless loop in
pick_next_task()"), which is not necessary after ("sched/rt: Substract number
of tasks of throttled queues from rq->nr_running").
Signed-off-by: Kirill Tkhai <tkhai@yandex.ru>
Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
[conflict resolution with stop task checking patch]
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1394835307.18748.34.camel@HP-250-G1-Notebook-PC
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Now rq->rt becomes to be able to be in dequeued or enqueued state.
We add new member rt_rq->rt_queued, which is used to indicate this.
The member is used only for top queue rq->rt_rq.
The goal is to fit generic scheme which is used in deadline and
fair classes, i.e. throttled rt_rq's rt_nr_running is beeing
substracted from rq->nr_running.
Signed-off-by: Kirill Tkhai <tkhai@yandex.ru>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1394835300.18748.33.camel@HP-250-G1-Notebook-PC
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
{inc,dec}_rt_tasks() used to count entities which are directly queued
on the rt_rq. If an entity was not a task (i.e., it is some queue), its
children were not counted.
There is no problem here, but now we want to count number of all tasks
which are actually queued under the rt_rq in all the hierarchy (except
throttled rt queues).
Empty queues are not able to be queued and all of the places, which
use ->rt_nr_running, just compare it with zero, so we do not break
anything here.
Signed-off-by: Kirill Tkhai <tkhai@yandex.ru>
Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1394835289.18748.31.camel@HP-250-G1-Notebook-PC
Cc: linux-kernel@vger.kernel.org
[ Twiddled the changelog. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Just switched pinned task is not able to be pushed. If the rq had had
several RT tasks before they have already been considered as candidates
to be pushed (or pulled).
Signed-off-by: Kirill V Tkhai <tkhai@yandex.ru>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20140312061833.3a43aa64@gandalf.local.home
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Mike reported that, while unlikely, its entirely possible for
scale_rt_power() to see the time go backwards. This yields rather
'interesting' results.
So like all other sites that deal with clocks; make this one ignore
backward clock movement too.
Reported-by: Mike Galbraith <bitbucket@online.de>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20140227094035.GZ9987@twins.programming.kicks-ass.net
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull timer fixes from Thomas Gleixner:
"Viresh unearthed the following three hickups in the timer/timekeeping
code:
- Negated check for the result of a clock event selection
- A missing early exit in the jiffies update path which causes
update_wall_time to be called for nothing causing lock contention
and wasted cycles in the timer interrupt
- Checking a variable in the NOHZ code enable code for true which can
only be set by that very code after the check succeeds. That
results in a rock solid runtime disablement of that feature"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick-sched: Check tick_nohz_enabled in tick_nohz_switch_to_nohz()
tick-sched: Don't call update_wall_time() when delta is lesser than tick_period
tick-common: Fix wrong check in tick_check_replacement()
We need to do it like we do for the other higher priority classes..
Signed-off-by: Kirill Tkhai <tkhai@yandex.ru>
Cc: Michael wang <wangyun@linux.vnet.ibm.com>
Cc: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/336561397137116@web27h.yandex.ru
Signed-off-by: Ingo Molnar <mingo@kernel.org>
With the restructing of the function tracer working with instances, the
"top level" buffer is a bit special, as the function tracing is mapped
to the same set of filters. This is done by using a "global_ops" descriptor
and having the "set_ftrace_filter" and "set_ftrace_notrace" map to it.
When an instance is created, it creates the same files but its for the
local instance and not the global_ops.
The issues is that the local instance creation shares some code with
the global instance one and we end up trying to create th top level
"set_ftrace_*" files twice, and on boot up, we get an error like this:
Could not create debugfs 'set_ftrace_filter' entry
Could not create debugfs 'set_ftrace_notrace' entry
The reason they failed to be created was because they were created
twice, and the second time gives this error as you can not create the
same file twice.
Reported-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Pull networking fixes from David Miller:
1) Fix BPF filter validation of netlink attribute accesses, from
Mathias Kruase.
2) Netfilter conntrack generation seqcount not initialized properly,
from Andrey Vagin.
3) Fix comparison mask computation on big-endian in nft_cmp_fast(),
from Patrick McHardy.
4) Properly limit MTU over ipv6, from Eric Dumazet.
5) Fix seccomp system call argument population on 32-bit, from Daniel
Borkmann.
6) skb_network_protocol() should not use hard-coded ETH_HLEN, instead
skb->mac_len needs to be used. From Vlad Yasevich.
7) We have several cases of using socket based communications to
implement a tunnel. For example, some tunnels are encapsulations
over UDP so we use an internal kernel UDP socket to do the
transmits.
These tunnels should behave just like other software devices and
pass the packets on down to the next layer.
Most importantly we want the top-level socket (eg TCP) that created
the traffic to be charged for the SKB memory.
However, once you get into the IP output path, we have code that
assumed that whatever was attached to skb->sk is an IP socket.
To keep the top-level socket being charged for the SKB memory,
whilst satisfying the needs of the IP output path, we now pass in an
explicit 'sk' argument.
From Eric Dumazet.
8) ping_init_sock() leaks group info, from Xiaoming Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (33 commits)
cxgb4: use the correct max size for firmware flash
qlcnic: Fix MSI-X initialization code
ip6_gre: don't allow to remove the fb_tunnel_dev
ipv4: add a sock pointer to dst->output() path.
ipv4: add a sock pointer to ip_queue_xmit()
driver/net: cosa driver uses udelay incorrectly
at86rf230: fix __at86rf230_read_subreg function
at86rf230: remove check if AVDD settled
net: cadence: Add architecture dependencies
net: Start with correct mac_len in skb_network_protocol
Revert "net: sctp: Fix a_rwnd/rwnd management to reflect real state of the receiver's buffer"
cxgb4: Save the correct mac addr for hw-loopback connections in the L2T
net: filter: seccomp: fix wrong decoding of BPF_S_ANC_SECCOMP_LD_W
seccomp: fix populating a0-a5 syscall args in 32-bit x86 BPF
qlcnic: Do not disable SR-IOV when VFs are assigned to VMs
qlcnic: Fix QLogic application/driver interface for virtual NIC configuration
qlcnic: Fix PVID configuration on eSwitch port.
qlcnic: Fix max ring count calculation
qlcnic: Fix to send INIT_NIC_FUNC as first mailbox.
qlcnic: Fix panic due to uninitialzed delayed_work struct in use.
...
In tick_do_update_jiffies64() we are processing ticks only if delta is
greater than tick_period. This is what we are supposed to do here and
it broke a bit with this patch:
commit 47a1b796 (tick/timekeeping: Call update_wall_time outside the
jiffies lock)
With above patch, we might end up calling update_wall_time() even if
delta is found to be smaller that tick_period. Fix this by returning
when the delta is less than tick period.
[ tglx: Made it a 3 liner and massaged changelog ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: linaro-kernel@lists.linaro.org
Cc: fweisbec@gmail.com
Cc: Arvind.Chauhan@arm.com
Cc: linaro-networking@linaro.org
Cc: John Stultz <john.stultz@linaro.org>
Cc: <stable@vger.kernel.org> # v3.14+
Link: http://lkml.kernel.org/r/80afb18a494b0bd9710975bcc4de134ae323c74f.1397537987.git.viresh.kumar@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
smp_read_barrier_depends() can be used if there is data dependency between
the readers - i.e. if the read operation after the barrier uses address
that was obtained from the read operation before the barrier.
In this file, there is only control dependency, no data dependecy, so the
use of smp_read_barrier_depends() is incorrect. The code could fail in the
following way:
* the cpu predicts that idx < entries is true and starts executing the
body of the for loop
* the cpu fetches map->extent[0].first and map->extent[0].count
* the cpu fetches map->nr_extents
* the cpu verifies that idx < extents is true, so it commits the
instructions in the body of the for loop
The problem is that in this scenario, the cpu read map->extent[0].first
and map->nr_extents in the wrong order. We need a full read memory barrier
to prevent it.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus reports that on 32-bit x86 Chromium throws the following seccomp
resp. audit log messages:
audit: type=1326 audit(1397359304.356:28108): auid=500 uid=500
gid=500 ses=2 subj=unconfined_u:unconfined_r:chrome_sandbox_t:s0-s0:c0.c1023
pid=3677 comm="chrome" exe="/opt/google/chrome/chrome" sig=0
syscall=172 compat=0 ip=0xb2dd9852 code=0x30000
audit: type=1326 audit(1397359304.356:28109): auid=500 uid=500
gid=500 ses=2 subj=unconfined_u:unconfined_r:chrome_sandbox_t:s0-s0:c0.c1023
pid=3677 comm="chrome" exe="/opt/google/chrome/chrome" sig=0 syscall=5
compat=0 ip=0xb2dd9852 code=0x50000
These audit messages are being triggered via audit_seccomp() through
__secure_computing() in seccomp mode (BPF) filter with seccomp return
codes 0x30000 (== SECCOMP_RET_TRAP) and 0x50000 (== SECCOMP_RET_ERRNO)
during filter runtime. Moreover, Linus reports that x86_64 Chromium
seems fine.
The underlying issue that explains this is that the implementation of
populate_seccomp_data() is wrong. Our seccomp data structure sd that
is being shared with user ABI is:
struct seccomp_data {
int nr;
__u32 arch;
__u64 instruction_pointer;
__u64 args[6];
};
Therefore, a simple cast to 'unsigned long *' for storing the value of
the syscall argument via syscall_get_arguments() is just wrong as on
32-bit x86 (or any other 32bit arch), it would result in storing a0-a5
at wrong offsets in args[] member, and thus i) could leak stack memory
to user space and ii) tampers with the logic of seccomp BPF programs
that read out and check for syscall arguments:
syscall_get_arguments(task, regs, 0, 1, (unsigned long *) &sd->args[0]);
Tested on 32-bit x86 with Google Chrome, unfortunately only via remote
test machine through slow ssh X forwarding, but it fixes the issue on
my side. So fix it up by storing args in type correct variables, gcc
is clever and optimizes the copy away in other cases, e.g. x86_64.
Fixes: bd4cf0ed33 ("net: filter: rework/optimize internal BPF interpreter's instruction set")
Reported-and-bisected-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Eric Paris <eparis@redhat.com>
Cc: James Morris <james.l.morris@oracle.com>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commits 11d4616bd0 ("futex: revert back to the explicit waiter
counting code") and 69cd9eba38 ("futex: avoid race between requeue and
wake") changed some of the finer details of how we think about futexes.
One was a late fix and the other a consequence of overlooking the whole
requeuing logic.
The first change caused our documentation to be incorrect, and the
second made us aware that we need to explicitly add more details to it.
Signed-off-by: Davidlohr Bueso <davidlohr@hp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull vfs updates from Al Viro:
"The first vfs pile, with deep apologies for being very late in this
window.
Assorted cleanups and fixes, plus a large preparatory part of iov_iter
work. There's a lot more of that, but it'll probably go into the next
merge window - it *does* shape up nicely, removes a lot of
boilerplate, gets rid of locking inconsistencie between aio_write and
splice_write and I hope to get Kent's direct-io rewrite merged into
the same queue, but some of the stuff after this point is having
(mostly trivial) conflicts with the things already merged into
mainline and with some I want more testing.
This one passes LTP and xfstests without regressions, in addition to
usual beating. BTW, readahead02 in ltp syscalls testsuite has started
giving failures since "mm/readahead.c: fix readahead failure for
memoryless NUMA nodes and limit readahead pages" - might be a false
positive, might be a real regression..."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (63 commits)
missing bits of "splice: fix racy pipe->buffers uses"
cifs: fix the race in cifs_writev()
ceph_sync_{,direct_}write: fix an oops on ceph_osdc_new_request() failure
kill generic_file_buffered_write()
ocfs2_file_aio_write(): switch to generic_perform_write()
ceph_aio_write(): switch to generic_perform_write()
xfs_file_buffered_aio_write(): switch to generic_perform_write()
export generic_perform_write(), start getting rid of generic_file_buffer_write()
generic_file_direct_write(): get rid of ppos argument
btrfs_file_aio_write(): get rid of ppos
kill the 5th argument of generic_file_buffered_write()
kill the 4th argument of __generic_file_aio_write()
lustre: don't open-code kernel_recvmsg()
ocfs2: don't open-code kernel_recvmsg()
drbd: don't open-code kernel_recvmsg()
constify blk_rq_map_user_iov() and friends
lustre: switch to kernel_sendmsg()
ocfs2: don't open-code kernel_sendmsg()
take iov_iter stuff to mm/iov_iter.c
process_vm_access: tidy up a bit
...
design of tracepoints and how a user could register a tracepoint
and have that tracepoint not be activated but no error was shown.
The design was for an out of tree module but broke in tree users.
The clean up was to remove the saving of the hash table of tracepoint
names such that they can be enabled before they exist (enabling
a module tracepoint before that module is loaded). This added more
complexity than needed. The clean up was to remove that code and
just enable tracepoints that exist or fail if they do not.
This removed a lot of code as well as the complexity that it brought.
As a side effect, instead of registering a tracepoint by its name,
the tracepoint needs to be registered with the tracepoint descriptor.
This removes having to duplicate the tracepoint names that are
enabled.
The second patch was added that simplified the way modules were
searched for.
This cleanup required changes that were in the 3.15 queue as well as
some changes that were added late in the 3.14-rc cycle. This final
change waited till the two were merged in upstream and then the
change was added and full tests were run. Unfortunately, the
test found some errors, but after it was already submitted to the
for-next branch and not to be rebased. Sparse errors were detected
by Fengguang Wu's bot tests, and my internal tests discovered that
the anonymous union initialization triggered a bug in older gcc compilers.
Luckily, there was a bugzilla for the gcc bug which gave a work around
to the problem. The third and fourth patch handled the sparse error
and the gcc bug respectively.
A final patch was tagged along to fix a missing documentation for
the README file.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTR+pwAAoJEKQekfcNnQGuvfoH/A4XZu4/1h2ZuKhzGi6lrrWr
+zHUQ+JmGiAYRziQFwr2t/gqJ2vmDfHJnbDjKi6Emx8JcxesHas6CQOWps4zEic0
dwYSQjvuGNGFIFt+7I0K1OxfVVdt2PQ2lVrB5WgYdbash5J4Bi+09QBv0RbUKheo
37dKSeN3pbsuQsR70OTVP8laG3dA9IbHW7PsKnxIEB5zeIUHUBME/QdPPj/CuJwk
wxZjXC2dbc3rdRlQjTVtWV3ZkGgZJB0k+JxjvZTA0N6u8Hj8LiFPuNawzf7ceBHx
gc++57+WuMW0f0X/ar5/+3UPGFQKMSvKmdxIQCnWXQz5seTYYKDEx7mTH22fxgg=
=OgeQ
-----END PGP SIGNATURE-----
Merge tag 'trace-3.15-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull more tracing updates from Steven Rostedt:
"This includes the final patch to clean up and fix the issue with the
design of tracepoints and how a user could register a tracepoint and
have that tracepoint not be activated but no error was shown.
The design was for an out of tree module but broke in tree users. The
clean up was to remove the saving of the hash table of tracepoint
names such that they can be enabled before they exist (enabling a
module tracepoint before that module is loaded). This added more
complexity than needed. The clean up was to remove that code and just
enable tracepoints that exist or fail if they do not.
This removed a lot of code as well as the complexity that it brought.
As a side effect, instead of registering a tracepoint by its name, the
tracepoint needs to be registered with the tracepoint descriptor.
This removes having to duplicate the tracepoint names that are
enabled.
The second patch was added that simplified the way modules were
searched for.
This cleanup required changes that were in the 3.15 queue as well as
some changes that were added late in the 3.14-rc cycle. This final
change waited till the two were merged in upstream and then the change
was added and full tests were run. Unfortunately, the test found some
errors, but after it was already submitted to the for-next branch and
not to be rebased. Sparse errors were detected by Fengguang Wu's bot
tests, and my internal tests discovered that the anonymous union
initialization triggered a bug in older gcc compilers. Luckily, there
was a bugzilla for the gcc bug which gave a work around to the
problem. The third and fourth patch handled the sparse error and the
gcc bug respectively.
A final patch was tagged along to fix a missing documentation for the
README file"
* tag 'trace-3.15-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Add missing function triggers dump and cpudump to README
tracing: Fix anonymous unions in struct ftrace_event_call
tracepoint: Fix sparse warnings in tracepoint.c
tracepoint: Simplify tracepoint module search
tracepoint: Use struct pointer instead of name hash for reg/unreg tracepoints
Pull audit updates from Eric Paris.
* git://git.infradead.org/users/eparis/audit: (28 commits)
AUDIT: make audit_is_compat depend on CONFIG_AUDIT_COMPAT_GENERIC
audit: renumber AUDIT_FEATURE_CHANGE into the 1300 range
audit: do not cast audit_rule_data pointers pointlesly
AUDIT: Allow login in non-init namespaces
audit: define audit_is_compat in kernel internal header
kernel: Use RCU_INIT_POINTER(x, NULL) in audit.c
sched: declare pid_alive as inline
audit: use uapi/linux/audit.h for AUDIT_ARCH declarations
syscall_get_arch: remove useless function arguments
audit: remove stray newline from audit_log_execve_info() audit_panic() call
audit: remove stray newlines from audit_log_lost messages
audit: include subject in login records
audit: remove superfluous new- prefix in AUDIT_LOGIN messages
audit: allow user processes to log from another PID namespace
audit: anchor all pid references in the initial pid namespace
audit: convert PPIDs to the inital PID namespace.
pid: get pid_t ppid of task in init_pid_ns
audit: rename the misleading audit_get_context() to audit_take_context()
audit: Add generic compat syscall support
audit: Add CONFIG_HAVE_ARCH_AUDITSYSCALL
...
that commit has fixed only the parts of that mess in fs/splice.c itself;
there had been more in several other ->splice_read() instances...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
debug_mutex_unlock() would bail when !debug_locks and forgets to
actually unlock.
Reported-by: "Michael L. Semon" <mlsemon35@gmail.com>
Reported-by: "Kirill A. Shutemov" <kirill@shutemov.name>
Reported-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Fixes: 6f008e72cd ("locking/mutex: Fix debug checks")
Tested-by: Dave Jones <davej@redhat.com>
Cc: Jason Low <jason.low2@hp.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20140410141559.GE13658@twins.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Sasha reported that lockdep claims that the following commit:
made numa_group.lock interrupt unsafe:
156654f491 ("sched/numa: Move task_numa_free() to __put_task_struct()")
While I don't see how that could be, given the commit in question moved
task_numa_free() from one irq enabled region to another, the below does
make both gripes and lockups upon gripe with numa=fake=4 go away.
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Fixes: 156654f491 ("sched/numa: Move task_numa_free() to __put_task_struct()")
Signed-off-by: Mike Galbraith <bitbucket@online.de>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: torvalds@linux-foundation.org
Cc: mgorman@suse.com
Cc: akpm@linux-foundation.org
Cc: Dave Jones <davej@redhat.com>
Link: http://lkml.kernel.org/r/1396860915.5170.5.camel@marge.simpson.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The debugfs tracing README file lists all the function triggers except for
dump and cpudump. These should be added too.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Jan Stancek reported:
"pthread_cond_broadcast/4-1.c testcase from openposix testsuite (LTP)
occasionally fails, because some threads fail to wake up.
Testcase creates 5 threads, which are all waiting on same condition.
Main thread then calls pthread_cond_broadcast() without holding mutex,
which calls:
futex(uaddr1, FUTEX_CMP_REQUEUE_PRIVATE, 1, 2147483647, uaddr2, ..)
This immediately wakes up single thread A, which unlocks mutex and
tries to wake up another thread:
futex(uaddr2, FUTEX_WAKE_PRIVATE, 1)
If thread A manages to call futex_wake() before any waiters are
requeued for uaddr2, no other thread is woken up"
The ordering constraints for the hash bucket waiter counting are that
the waiter counts have to be incremented _before_ getting the spinlock
(because the spinlock acts as part of the memory barrier), but the
"requeue" operation didn't honor those rules, and nobody had even
thought about that case.
This fairly simple patch just increments the waiter count for the target
hash bucket (hb2) when requeing a futex before taking the locks. It
then decrements them again after releasing the lock - the code that
actually moves the futex(es) between hash buckets will do the additional
required waiter count housekeeping.
Reported-and-tested-by: Jan Stancek <jstancek@redhat.com>
Acked-by: Davidlohr Bueso <davidlohr@hp.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org # 3.14
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the following sparse warnings:
CHECK kernel/tracepoint.c
kernel/tracepoint.c:184:18: warning: incorrect type in assignment (different address spaces)
kernel/tracepoint.c:184:18: expected struct tracepoint_func *tp_funcs
kernel/tracepoint.c:184:18: got struct tracepoint_func [noderef] <asn:4>*funcs
kernel/tracepoint.c:216:18: warning: incorrect type in assignment (different address spaces)
kernel/tracepoint.c:216:18: expected struct tracepoint_func *tp_funcs
kernel/tracepoint.c:216:18: got struct tracepoint_func [noderef] <asn:4>*funcs
kernel/tracepoint.c:392:24: error: return expression in void function
CC kernel/tracepoint.o
kernel/tracepoint.c: In function tracepoint_module_going:
kernel/tracepoint.c:491:6: warning: symbol 'syscall_regfunc' was not declared. Should it be static?
kernel/tracepoint.c:508:6: warning: symbol 'syscall_unregfunc' was not declared. Should it be static?
Link: http://lkml.kernel.org/r/1397049883-28692-1-git-send-email-mathieu.desnoyers@efficios.com
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Instead of copying the num_tracepoints and tracepoints_ptrs from
the module structure to the tp_mod structure, which only uses it to
find the module associated to tracepoints of modules that are coming
and going, simply copy the pointer to the module struct to the tracepoint
tp_module structure.
Also removed un-needed brackets around an if statement.
Link: http://lkml.kernel.org/r/20140408201705.4dad2c4a@gandalf.local.home
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Register/unregister tracepoint probes with struct tracepoint pointer
rather than tracepoint name.
This change, which vastly simplifies tracepoint.c, has been proposed by
Steven Rostedt. It also removes 8.8kB (mostly of text) to the vmlinux
size.
From this point on, the tracers need to pass a struct tracepoint pointer
to probe register/unregister. A probe can now only be connected to a
tracepoint that exists. Moreover, tracers are responsible for
unregistering the probe before the module containing its associated
tracepoint is unloaded.
text data bss dec hex filename
10443444 4282528 10391552 25117524 17f4354 vmlinux.orig
10434930 4282848 10391552 25109330 17f2352 vmlinux
Link: http://lkml.kernel.org/r/1396992381-23785-2-git-send-email-mathieu.desnoyers@efficios.com
CC: Ingo Molnar <mingo@kernel.org>
CC: Frederic Weisbecker <fweisbec@gmail.com>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Frank Ch. Eigler <fche@redhat.com>
CC: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
[ SDR - fixed return val in void func in tracepoint_module_going() ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Merge second patch-bomb from Andrew Morton:
- the rest of MM
- zram updates
- zswap updates
- exit
- procfs
- exec
- wait
- crash dump
- lib/idr
- rapidio
- adfs, affs, bfs, ufs
- cris
- Kconfig things
- initramfs
- small amount of IPC material
- percpu enhancements
- early ioremap support
- various other misc things
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (156 commits)
MAINTAINERS: update Intel C600 SAS driver maintainers
fs/ufs: remove unused ufs_super_block_third pointer
fs/ufs: remove unused ufs_super_block_second pointer
fs/ufs: remove unused ufs_super_block_first pointer
fs/ufs/super.c: add __init to init_inodecache()
doc/kernel-parameters.txt: add early_ioremap_debug
arm64: add early_ioremap support
arm64: initialize pgprot info earlier in boot
x86: use generic early_ioremap
mm: create generic early_ioremap() support
x86/mm: sparse warning fix for early_memremap
lglock: map to spinlock when !CONFIG_SMP
percpu: add preemption checks to __this_cpu ops
vmstat: use raw_cpu_ops to avoid false positives on preemption checks
slub: use raw_cpu_inc for incrementing statistics
net: replace __this_cpu_inc in route.c with raw_cpu_inc
modules: use raw_cpu_write for initialization of per cpu refcount.
mm: use raw_cpu ops for determining current NUMA node
percpu: add raw_cpu_ops
slub: fix leak of 'name' in sysfs_slab_add
...
When the system has only one CPU, lglock is effectively a spinlock; map
it directly to spinlock to eliminate the indirection and duplicate code.
In addition to removing overhead, this drops 1.6k of code with a
defconfig modified to have !CONFIG_SMP, and 1.1k with a minimal config.
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: David Howells <dhowells@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
