Set the module parameter ql2xmultique_tag to 1 to enable this
feature. In this mode, the total number of response queues
created is equal to the number of online cpus. Turning the block
layer's rq_affinity mode on enables requests to be routed to the
proper cpu and at the same time it enables completion of the IO
in a response queue that is affined to the cpu in the request
path.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Set the number of request queues to the module paramater
ql2xmaxqueues. Each vport gets a request queue. The QoS value
set to the request queues determines priority control for queued
IOs. If QoS value is not specified, the vports use the default
queue 0.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The short-circuit to skip the non-applicable 'full-login-lip'
process on 81xx ISPs was nested too deeply in the 'bus-reset'
routine, as the code in qla2x00_loop_reset() should skip the
whole enable_lip_full_login process. The original code could
cause device tear-down due to the qla2x00_wait_for_loop_ready()
call taking a large amount of time.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In addition to checking for potentially unnecessary iomem
readX()/writeX() operations, a pci_channel_io_perm_failure should
not trigger a full internal removal. Found during additional
testing with pSeries blade systems.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Rather than assuming a particular layout of the data. Applies to
recent ISPs only.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Interface allows for the update of onboard EDC firmware
present on mezzanine ISP25xx type cards.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
General cleanup of extraneous/legacy crud.
Additional cleanups and
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Ensure that an ISP-abort has completed before performing any
update. After the update do not wait for an ISP-abort completion,
instead just wait until the ISP is reset. This avoids long
delays due to waiting for loop ready in qla2x00_abort_isp().
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Additional cleanups and
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Since the routines can/will use resources such as devices and
rports that aren't valid after midlayer tear-down, correct this
potential race, by stopping the offending during the early stages
of the remove() callback.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
As all commands queued on the physical HBA should be aborted and
returned to the upper-layers.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Recent ISPs use this data to configure FCF information.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Post refactoring/multi-queue additions essentially eliminated the
need for separate ISP24XX+ queuecommand as isp_ops contains a
function pointer to the associated 'start_scsi()' operation.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Original code used an overabundance of indirect pointers to
function helpers. Instead, the driver can exploit the immutable
properties of a queue's ISP-association and ID, which are both
known at queue initialization-time.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The value is already pre-assigned prior to the qla2x00_mem_alloc().
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
QLA_* return codes are 'int' in size. There were still several
legacy check-points which assumed a return-code width of 8-bits.
This could cause incorrect assumptions of 'good' status if a
return of QLA_FUNCTION_TIMEOUT.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
To ensure smooth operations amongst the FCoE and NIC side
components of the ISP81xx chip, the FCoE driver (qla2xxx) must
ensure the 10gb NIC driver (qlge) does not timeout waiting for
IDC (Inter-Driver Communication) acknowledgments. The
acknowledgment requirements are trivial -- a simple mirroring of
incoming mailbox registers during the AEN to a process-context
capable mailbox command.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Jeremy Higdon noted
(http://marc.info/?l=linux-scsi&m=123262143131788&w=2) that the
rework done in commit e315cd28b9
was not setting the proper consistent and streaming DMA masks
prior to memory allocations. Correct this and remove the
unnecessary prototype.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Commit 73208dfd7a (qla2xxx: add
support for multi-queue adapter) inadvertently backed-out the fix
in 5bff55db3d (qla2xxx: Return a
FAILED status when abort mailbox-command fails.).
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Pre-ISP81XX parts (including ISP24xx and ISP25xx) could contain a
firmware image within a segment of flash, driver would fallback
to loading this firmware if the request-firmware interface failed
(userspace .bin file). Moving forward, all ISP81XX parts will
ship with a suggested-to-be-used firmware image within flash
which all driver should first attempt to load. If the flash
firmware load fails, the driver will then fallback to loading
firmware via the request-firmware interface (ql8100_fw.bin).
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
After restarting ISP the additional queues are not being setup correctly. The
following patch fixes the issue.
Please apply.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Codes to support new FCoE boards.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Original code would inadvertanly place I/Os on the default
request-queue. Also, correctly pass in the proper MSI-X vector
during response-queue initialization.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
ROMs in recent ISPs have MSI-X support, so it's no longer
necessary for the driver to fallback to interrupt polling during
ISP re-initialization.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Software should not touch this region of flash, as the firmware
will be the only writer and consumer of the region.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Following changes have been made:
1. Scan outstanding commands only in the queue where it is submitted
2. Update queue registers directly in the fast path
3. Queue specific BAR is remapped only for multiq capable adapters
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Following changes have been made.
1. qla_hw_data structure holds an array for request queue pointers,
and an array for response queue pointers.
2. The base request and response queues are created by default.
3. Additional request and response queues are created at the time of vport
creation. If queue resources are exhausted during vport creation, newly
created vports use the default queue.
4. Requests are sent to the request queue that the vport was assigned
in the beginning.
5. Responses are completed on the response queue with which the request queue
is associated with.
[fixup memcpy argument reversal spotted by davej@redhat.com]
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The following patch changes the handling of bus reset when issued from a
vport. In the bus reset code, an extra check is made to make sure that the lip
reset is not done before resetting the targets if the bus reset came from a
vport.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
drivers/scsi/qla2xxx/qla_os.c: In function 'qla2x00_probe_one':
drivers/scsi/qla2xxx/qla_os.c:1582: warning: 'mem_only' is used uninitialized in this function
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Following changes have been made:
1. Outstanding commands are based on a request queue, scsi_qla_host
does not maintain it anymore.
2. start_scsi is accessed via isp_ops struct instead of direct
invocation.
3. Interrupt registrations are done using response queue instead of
device id.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Mike Reed noted
(https://bugzilla.novell.com/show_bug.cgi?id=421330) that the
driver was incorrectly returning a SUCCESS status if the driver's
request to the firmware to abort a command failed. By doing so,
the mid-layer believed, incorrectly, that the command has
completed and has been returned (ultimately clearing
scsi_cmnd.request_buffer) yet the driver still has the command.
What should correctly happen is a mid-layer escalation
(device-reset, etc.) of recovery during which the driver will
eventually return the outstanding commands to the mid-layer.
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Remove some open coded (and buggy) versions of pci_find_ext_capability
in favor of the real routine in the PCI core.
Tested-by: Tomasz Czernecki <czernecki@gmail.com>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If the fcport is not online then we do not want to block IO to all ports on
the host. We just want to stop IO on port not online, so we should be using
the SCSI_MLQUEUE_TARGET_BUSY return value.
For the case where we race with the rport memset initialization
we do not want the queuecommand to be called again so we can just use
SCSI_MLQUEUE_TARGET_BUSY for this.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
To instatiate pre-configured vport entities defined within an
HBA's flash memory.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The Flash Layout Table (FLT) present on many recent HBAs encodes
flash usage information, organizes data stored into separate
regions and presents the information uniformly to the driver.
Use this information rather than using specific hard-coded values
based on ISP type.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Josip Rodin noted
(http://article.gmane.org/gmane.linux.ports.sparc/10152) the
driver oopsing during registration of an rport to the
FC-transport layer with a backtrace indicating a dereferencing of
an shost->shost_data equal to NULL. David Miller identified a
small window in driver logic where this could happen:
> Look at how the driver registers the IRQ handler before the host has
> been registered with the SCSI layer.
>
> That leads to a window of time where the shost hasn't been setup
> fully, yet ISRs can come in and trigger DPC thread events, such as
> loop resyncs, which expect the transport area to be setup.
>
> But it won't be setup, because scsi_add_host() hasn't finished yet.
>
> Note that in Josip's crash log, we don't even see the
>
> qla_printk(KERN_INFO, ha, "\n"
> " QLogic Fibre Channel HBA Driver: %s\n"
> " QLogic %s - %s\n"
> " ISP%04X: %s @ %s hdma%c, host#=%ld, fw=%s\n",
> ...
>
> message yet.
>
> Which means that the crash occurs between qla2x00_request_irqs()
> and printing that message.
Close this window by enabling RISC interrupts after the host has
been registered with the SCSI midlayer.
Reported-by: Josip Rodin <joy@entuzijast.net>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
During internal testing, we've seen issues (hangs) with the
'deferred' vport tear-down-processing typically accompanied with
the fc_remove_host() call. This is due to the current
implementation's back-end vport handling being performed by the
physical-HA's DPC thread where premature shutdown could lead to
latent vport requests without a processor.
This should also address a problem reported by Gal Rosen
(http://marc.info/?l=linux-scsi&m=121731664417358&w=2) where the
driver would attempt to awaken a previously torn-down DPC thread
from interrupt context by implicitly calling wake_up_process()
rather than the driver's qla2xxx_wake_dpc() helper. Rather, than
reshuffle the remove_one() device-removal code, during unload,
depend on the driver's timer to wake-up the DPC process, by
limiting wake-ups based on an 'unloading' flag.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The executing-HA of an SRB can be referenced from the sp->fcport.
Use this correct value while processing status-continuation data
and abort processing.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Original code inadvertently cleared an SRB's 'flags' while
aborting; causing a follow-on scsi_dma_unmap() to be potentially
missed.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Minor fixes addressing:
- rport managements during vport deletion.
- acquire proper physical-ha during qla24xx_abort_command() and
qla24xx_queuecommand()
- do not needlessly acquire the pha for non-NPIV capable ISPs.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
drivers/scsi/qla2xxx/qla_os.c: In function 'qla2x00_post_work':
drivers/scsi/qla2xxx/qla_os.c:2158: warning: 'flags' may be used uninitialized in this function
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There were several issues here, one, during RSCN handling if a
follow-on RSCN occurred (within interrupt context) the DPC thread
could inadvertantly leave the fcport in a stale lost state.
Secondly, scheduled rport removal is handled exclusively by the
'parent' DPC thread, so wake up the proper thread. Finally,
process vport loop-resync's only when the vport has in an
"active" state (ID acquired).
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
All fcport->state management should be done within
qla2x00_mark_device_lost(), the assignment of state within
qla2x00_mark_vp_devices_dead() caused associated rports to not be
removed.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
iIDMA support requires the driver issue several additional
fabric-managegment (FM) commands per port discovered during SNS
scanning -- GFPN (Get Fabric Port Name) and GPSC (Get Port Speed
Capabilities). It has been found during testing that some
switches do not respond as *well* as expected to these commands
(silence -- no ACC nor BS_RJT). So, to handle such conditions,
allow the user the ability to indirectly disable the FM commands
by disabling iIDMA with the ql2xiidmaenable module-parameter.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Removed repeated or unnecessary operations during vport
creation/deletion.
Signed-off-by: Shyam Sundar <shyam.sundar@qlogic.com>
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
As there's no point in adding a fixed-fudge value (originally 5
seconds), honor the user settings only. We also remove the
driver's dead-callback get_rport_dev_loss_tmo function
(qla2x00_get_rport_loss_tmo()).
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Initialize all proper structure members in order to support
work-list vport processing. This code also properly acquires the
correct (physical hardware_lock) lock during work submission.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
