Size of event log is determined by uCode which is different per NICs.
Set the maximum event log size per device to better match uCode
configuration.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Resolution of a merge conflict upstream accidentally removed a hunk of
"ath5k: IQ calibration for AR5211 is slightly different", so restore it.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simple pre-scan and scan complete callbacks, this at least shows
to me that mac80211 will issue two scans at the same time on the
same wiphy.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We check the bounds on pdadc once when correcting for
negative curves but not when we later copy values from
from the pdadc_tmp array, leading to a potential overrun.
Although we shouldn't hit this case in practice, let's
be consistent.
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As pointed out by Benoit Papillault, there is a potential
race condition between the host and the hardware in reading
the next link in the transmit descriptor list:
cpu0 hw
tx for buf completed
raise tx_ok interrupt
process buf
buf->ds_link = 0
read buf->ds_link
This change checks txdp before processing a descriptor
(if there are any subsequent descriptors) to see if
hardware moved on. We'll then process this descriptor on
the next tasklet.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Review spotted a couple of strange invocations to
ieee80211_wake_queues that could potentially cause problems:
- queues are awakened in the calibration tasklet before
phy calibration, and then again after calibration
- queues are awakened inside reset when we're trying to
drain the ath5k transmit queues, and again after
reset is completed (in callers to ath5k_reset_wake).
In both cases the first wake is unnecessary, so remove it.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These channels aren't selectable anyway, but our calculations
for 2.5 mhz frequencies are incorrect. The value is supposed to
be:
(frequency - reference) * (10/25)
i.e., divide by 2.5, but we were instead doing:
(10 * frequency - reference) / 25.
Additionally, the check for (frequency % 5 == 2) had an extra
subtraction that wasn't in madwifi HAL.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2872 needs the same rf register setup as rt3070 and rt3090, hence
use rt2800_config_channel_rt3x instead of rt2800_config_channel_rt2x.
This change allows me to actually switch channels and hence scan all
configured channels on the RT305x SoC platform (which uses a rt2872)
here.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Tested-by: Luis Correia <luis.f.correia@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't modify ah->iniModes, it's supposed to be constant. Instead, apply
the fixup when the data is written to the registers.
Change ath9k_hw_init_eeprom_fix() to only determine whether the fixup is
needed.
This allows similteneous support for AR9220 cards that need AR_AN_TOP2
fixup (such as Ubiquiti SR71-12) and those that don't need it (D-Link
DWA-552 rev A2).
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Messages that are generated by the HTC layer
don't have any TX callback endpoints assigned to them.
Consequently, the allocated SKBs are never freed.
Fix this issue by handling this case in the HTC layer
itself.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
hif_usb_regout_cb() frees the given URB, which is
borked by design. Use an anchor to simplify URB
management.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The maximum number of packets in a single buffer in
stream mode is 10. The driver currently uses 8 - which
caused stack corruption, in the absence of any kind
of OOB checking.
Fixing this to the correct value of 10 fixes the module
unload issue.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Tested-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RX URBs are automatically freed when the reference
count drops to zero - this currently doesn't happen when
usb_kill_anchored_urbs() is called during unload.
Fix this by dropping the reference count by one during
initial submission.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a spin lock to prevent concurrent access
to variables dealing with RX stream mode handling.
Currently, no protection is implemented - which
causes problems in RX.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that the powersave issues on rt2500usb have been tackled, powersave
can be enabled by default again.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for a modified newer version of AR9285
chipsets.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Better use the macro for consistency, the content is the same anyway.
Signed-off-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is an Adaptive Noise Imunity (ANI) implementation for ath5k. I have looked
at both ath9k and HAL sources (they are nearly the same), and even though i
have implemented some things differently, the basic algorithm is practically
the same, for now. I hope that this can serve as a clean start to improve the
algorithm later.
This also adds a possibility to manually control ANI settings, right now only
thru a debugfs file:
* set lowest sensitivity (=highest noise immunity):
echo sens-low > /sys/kernel/debug/ath5k/phy0/ani
* set highest sensitivity (=lowest noise immunity):
echo sens-high > /sys/kernel/debug/ath5k/phy0/ani
* automatically control immunity (default):
echo ani-on > /sys/kernel/debug/ath5k/phy0/ani
* to see the parameters in use and watch them change:
cat /sys/kernel/debug/ath5k/phy0/ani
Manually setting sensitivity will turn the automatic control off. You can also
control each of the five immunity parameters (noise immunity, spur immunity,
firstep, ofdm weak signal detection, cck weak signal detection) manually thru
the debugfs file.
This is tested on AR5414 and nearly doubles the thruput in a noisy 2GHz band.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch modifies tx-queue flushing to correspond with tx-path - i.e.
also frames for which no ack was requested are forwarded to the mac80211
for disposal.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove ERROR print from psm-entry-fail scenario, instead use an INFO print.
Also, add INFO print to the beacon-loss scenario.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Increase the fixed listen-interval max value configured to the mac80211 on
driver init. This value will allow a larger value to be configured to the
AP, which means the AP will buffer our frames longer.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Configure meaningful rates to be used with the templates. For control frames,
use the determined basic rates (currently the lowest rate for the band) and
for data-frames (null-funcs) let the firmware use the current rate policy to
determine the rate.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the mac80211 is not telling a hardware rate controlled driver a
rate to use for association frames etc. So to be safe, use the lowest rate
of each band for communication.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware does not like the host configuring the keep-alive after it has
been once configured after a join-operation. Instead, it will complain about
invalid parameters, which do not break functionality, but do not look nice
in the syslog either.
This patch prevents the complaints by only configuring the keep-alive once
for an association, after the first time join is performed with the correct
bssid.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The command header was missing in the wl1271_cmd_disconnect structure. It
was working fine by sheer luck, because the parameters are not critical and
because our wl1271_cmd_send() function was overwriting the rx_config_options
with the actual header.
This patch adds the header to the command structure.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Our SPI driver is called "wl1271_spi" in the driver information structure.
Let's use the same for SDIO so that things are aligned.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For USB devices, this check is invalid.
Remove the check so that new product IDs can be added.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This can be used to store the bus types ( AHB/PCI/USB ).
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commits 8e6f5aa250 and
db1a052b73 accidentally introduced
compile errors that happens when ath9k debug is not enabled.
This patch fixes the declaration of the inline stubs to resolve this.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ah->mask_reg was used to hold different data throughout the driver.
ath9k_hw_init_interrupt_masks() used it to save the value written to
AR_IMR. ath9k_hw_set_interrupts() used it to hold the interrupt mask as
defined in enum ath9k_int. Those masks differ in many bits.
Use ah->imask instead of ah->mask_reg in ath9k_hw_set_interrupts() and
ath9k_hw_updatetxtriglevel(). That's what the code was meant to do.
ah->imask is initialized in ath9k_start(), so we don't need to
initialize it from ah->mask_reg.
Once it's done, ah->mask_reg becomes write-only, so it's replaced with a
local variable in ath9k_hw_init_interrupt_masks().
Signed-off-by: Pavel Roskin <proski@gnu.org>
Reported-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add ah variable in the functions that didn't have it and used sc->imask.
Replace sc->sc_ah with ah in those functions.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Symbols starting with "ATH9K_INT" are also used for interrupt mask.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a patch to files in ath/ar9170 that fixes a set of warnings
found by checkpatch.pl tool. A line over 80 characters, a few empty
spaces before tab and a few empty characters before a new line.
Signed-off-by: Luis de Bethencourt <luisbg@ubuntu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is needed to wake up the device automatically for receiving beacons,
and is required for proper powersave handling.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is needed to wake up the device automatically for receiving beacons,
and is required for proper powersave handling.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In all drivers ensure that auto wakeup is disabled before waking up the device.
This is needed to prevent connection stability issues and problems in waking up
the device.
Based upon a patch from Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When operating in 1-bit mode, SDAT1 is used as dedicated interrupt line.
However, the 8686 will only drive this line when the ECSI bit is set in
the CCCR_IF register.
Thanks to Alagu Sankar for pointing me in the right direction.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Alagu Sankar <alagusankar@embwise.com>
Cc: Volker Ernst <volker.ernst@txtr.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Holger Schurig <hs4233@mail.mn-solutions.de>
Cc: Bing Zhao <bzhao@marvell.com>
Cc: libertas-dev@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: linux-mmc@vger.kernel.org
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a patch to the ath/regd.c file that fixes two code
readability issues. A space between to separate two defines
and the indentation inside the ath_redg_is_eeprom_valid
function.
Signed-off-by: Luis de Bethencourt <luisbg@ubuntu.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a patch to the ath/hw.c file that fixes up a warning about
macros found by the checkpatch.pl tool, that said that complex values
should be enclosed in parenthesis.
Signed-off-by: Luis de Bethencourt <luisbg@ubuntu.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the enable_radio being uninitialized, ath_radio_enable() might be
called twice, which can leave some hardware in an undefined state.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ralink SoC platforms do not have an MCU.
Signed-off-by: Luis Correia <luis.f.correia@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Includes minor improvements in debugging messages in iwl-4965.c,
function iwl4965_is_temp_calib_needed().
Signed-off-by: Frans Pop <elendil@planet.nl>
Cc: Zhu Yi <yi.zhu@intel.com>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Cc: Intel Linux Wireless <ilw@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Some defines used by all agn devices, but the definitions were in
iwl-4965-hw.h, move those to iwl-agn-hw.h which is the better place for
those.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
