* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (166 commits)
Revert "ax25: zero length frame filtering in AX25"
Revert "netrom: zero length frame filtering in NetRom"
cfg80211: default CONFIG_WIRELESS_OLD_REGULATORY to n
mac80211/iwlwifi: move virtual A-MDPU queue bookkeeping to iwlwifi
mac80211: fix aggregation to not require queue stop
mac80211: add skb length sanity checking
mac80211: unify and fix TX aggregation start
mac80211: clean up __ieee80211_tx args
mac80211: rework the pending packets code
mac80211: fix A-MPDU queue assignment
mac80211: rewrite fragmentation
iwlwifi: show current driver status in user readable format
b43: Add BCM4307 PCI-ID
cfg80211: fix locking in nl80211_set_wiphy
mac80211: fix RX path
ath5k: properly drop packets from ops->tx
ar9170: single module build
ath9k: fix dma mapping leak of rx buffer upon rmmod
rt2x00: New USB ID for rt73usb
ath5k: warn and correct rate for unknown hw rate indexes
...
This reverts commit f99bcff7a2.
Like netrom, Alan Cox says that zero lengths have real meaning
and are useful in this protocol.
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit a3ac80a130.
Alan Cox says that zero length writes do have special meaning
and are useful in this protocol.
Signed-off-by: David S. Miller <davem@davemloft.net>
And update description and feature-removal schedule according
to the new plan.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes all the virtual A-MPDU-queue bookkeeping from
mac80211. Curiously, iwlwifi already does its own bookkeeping, so
it doesn't require much changes except where it needs to handle
starting and stopping the queues in mac80211.
To handle the queue stop/wake properly, we rewrite the software
queue number for aggregation frames and internally to iwlwifi keep
track of the queues that map into the same AC queue, and only talk
to mac80211 about the AC queue. The implementation requires calling
two new functions, iwl_stop_queue and iwl_wake_queue instead of the
mac80211 counterparts.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Reinette Chattre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of stopping the entire AC queue when enabling aggregation
(which was only done for hardware with aggregation queues) buffer
the packets for each station, and release them to the pending skb
queue once aggregation is turned on successfully.
We get a little more code, but it becomes conceptually simpler and
we can remove the entire virtual queue mechanism from mac80211 in
a follow-up patch.
This changes how mac80211 behaves towards drivers that support
aggregation but have no hardware queues -- those drivers will now
not be handed packets while the aggregation session is being
established, but only after it has been fully established.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We just found a bug in zd1211rw where it would reject
packets in the ->tx() method but leave them modified,
which would cause retransmit attempts with completely
bogus skbs, eventually leading to a panic due to not
having enough headroom in those.
This patch adds a sanity check to mac80211 to catch
such driver mistakes; in this case we warn and drop
the skb.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When TX aggregation becomes operational, we do a number of steps:
1) print a debug message
2) wake the virtual queue
3) notify the driver
Unfortunately, 1) and 3) are only done if the driver is first to
reply to the aggregation request, it is, however, possible that the
remote station replies before the driver! Thus, unify the code for
this and call the new function ieee80211_agg_tx_operational in both
places where TX aggregation can become operational.
Additionally, rename the driver notification from
IEEE80211_AMPDU_TX_RESUME to IEEE80211_AMPDU_TX_OPERATIONAL.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
__ieee80211_tx takes a struct ieee80211_tx_data argument, but only
uses a few of its members, namely 'skb' and 'sta'. Make that explicit,
so that less internal knowledge is required in ieee80211_tx_pending
and the possibility of introducing errors here is removed.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The pending packets code is quite incomprehensible, uses memory barriers
nobody really understands, etc. This patch reworks it entirely, using
the queue spinlock, proper stop bits and the skb queues themselves to
indicate whether packets are pending or not (rather than a separate
variable like before).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Internally, mac80211 requires the skb's queue mapping to be set
to the AC queue, not the virtual A-MPDU queue. This is not done
correctly currently, this patch moves the code down to directly
before the driver is invoked and adds a comment that it will be
moved into the driver later.
Since this requires __ieee80211_tx() to have the sta pointer,
make sure to provide it in ieee80211_tx_pending().
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fragmentation currently uses an allocated array to store the
fragment skbs, and then keeps track of which have been sent
and which are still pending etc. This is rather complicated;
make it simpler by just chaining the fragments into skb->next
and removing from that list when sent. Also simplifies all
code that needs to touch fragments, since it now only needs
to walk the skb->next list.
This is a prerequisite for fixing the stored packet code,
which I need to do for proper aggregation packet storing.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis reports that there's a circular locking dependency;
this is because cfg80211_dev_rename() will acquire the
cfg80211_mutex while the device mutex is held, while
this normally is done the other way around. The solution
is to open-code the device-getting in nl80211_set_wiphy
and require holding the mutex around cfg80211_dev_rename
rather than acquiring it within.
Also fix a bug -- rtnl locking is expected by drivers so
we need to provide it.
Reported-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My previous patch ("mac80211: remove mixed-cell and userspace MLME code")
was too obvious to me, so obvious that a stupid bug crept in. The IBSS
RX function must be invoked for IBSS, of course, not anything != IBSS.
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch changes mac80211 to not notify the rate control algorithm's
tx_status() method when reporting status for a packet that didn't go
through the rate control algorithm's get_rate() method.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add IEEE80211_HW_BEACON_FILTERING flag so that driver inform that it supports
beacon filtering. Drivers need to call the new function
ieee80211_beacon_loss() to notify about beacon loss.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In beacon filtering there needs to be a way to not expire the BSS even
when no beacons are received. Add an interface to cfg80211 to hold
BSS and make sure that it's not expired.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When software scanning we need to disable power save so that all possible
probe responses and beacons are received. For hardware scanning assume that
hardware will take care of that and document that assumption.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Separate beacon and rx path tracking in preparation for the beacon filtering
support. At the same time change ieee80211_associated() to look a bit simpler.
Probe requests are now sent only after IEEE80211_PROBE_IDLE_TIME, which
is now set to 60 seconds.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the timer is triggering every two seconds
(IEEE80211_MONITORING_INTERVAL). Decrease the timer to only trigger during
data idle periods to avoid waking up CPU unnecessary. The timer will
still trigger during idle periods, that needs to be fixed later.
There's also a functional change that probe requests are sent only when the
data path is idle, earlier they were sent also while there was activity
on the data path.
This is also preparation for the beacon filtering support. Thanks to
Johannes Berg for the idea.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Neither can currently be set from userspace, so there's no
regression potential, and neither will be supported from
userspace since the new userspace APIs allow the SME, which
is in userspace, to control all we need.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When somebody tries to set the interface mode to the existing
mode, don't ask the driver but silently accept the setting.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We had left in code to allow interested developers to add
support for parsing country IEs when OLD_REG was enabled.
This never happened and since we're going to remove OLD_REG
lets just remove these comments and code for it.
This code path was never being entered so this has no
functional change.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It seems a few users are using this module parameter although its not
recommended. People are finding it useful despite there being utilities
for setting this in userspace. I'm not aware of any distribution using
this though.
Until userspace and distributions catch up with a default userspace
automatic replacement (GeoClue integration would be nirvana) we copy
the ieee80211_regdom module parameter from OLD_REG to the new reg
code to help these users migrate.
Users who are using the non-valid ISO / IEC 3166 alpha "EU" in their
ieee80211_regdom module parameter and migrate to non-OLD_REG enabled
system will world roam.
This also schedules removal of this same ieee80211_regdom module
parameter circa March 2010. Hope is by then nirvana is reached and
users will abandoned the module parameter completely.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The incorrect assumption is the last regulatory request
(last_request) is always a country IE when processing
country IEs. Although this is true 99% of the time the
first time this happens this could not be true.
This fixes an oops in the branch check for the last_request
when accessing drv_last_ie. The access was done under the
assumption the struct won't be null.
Note to stable: to port to 29 replace as follows, only 29 has
country IE code:
s|NL80211_REGDOM_SET_BY_COUNTRY_IE|REGDOM_SET_BY_COUNTRY_IE
Cc: stable@kernel.org
Reported-by: Quentin Armitage <Quentin@armitage.org.uk>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Although EU is a bogus alpha2 we need to process the send request
as our code depends on last_request being set.
Cc: stable@kernel.org
Reported-by: Quentin Armitage <Quentin@armitage.org.uk>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do not want to require all the drivers using cfg80211 to need to do
this. In addition, make the error values consistent by using
EOPNOTSUPP instead of semi-random assortment of errno values.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do not want to require all the drivers using cfg80211 to need to do
this or to be prepared to handle these commands when the interface is
down.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check that the used authentication type and reason code are valid here
so that drivers/mac80211 do not need to care about this. In addition,
remove the unnecessary validation of SSID attribute length which is
taken care of by netlink policy.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The functionality that NL80211_CMD_SET_MGMT_EXTRA_IE provided can now
be achieved with cleaner design by adding IE(s) into
NL80211_CMD_TRIGGER_SCAN, NL80211_CMD_AUTHENTICATE,
NL80211_CMD_ASSOCIATE, NL80211_CMD_DEAUTHENTICATE, and
NL80211_CMD_DISASSOCIATE.
Since this is a very recently added command and there are no known (or
known planned) applications using NL80211_CMD_SET_MGMT_EXTRA_IE and
taken into account how much extra complexity it adds to the IE
processing we have now (and need to add in the future to fix IE order
in couple of frames), it looks like the best option is to just remove
the implementation of this command for now. The enum values themselves
are left to avoid changing the nl80211 command or attribute numbers.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This file was forgotten from the quilt patch that added MLME
primitives, so the kfree on interface removal is missing. Fix this
potential memleak by freeing the temporary Authentication frame IEs
from SME when the interface is being removed.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When mac80211 resumes, it currently doesn't reconfigure the interfaces
entirely and also doesn't reconfigure BSS information -- fix this.
Also, to be able to test this, add a debugfs file that just calls
the suspend/resume code to see what happens when we go through that,
without needing the time-consuming suspend/resume cycle.
(Original version broke the build for CONFIG_PM=n. Define alternative
functions for that situation. -- JWL)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds new nl80211 commands to allow user space to request
authentication and association (and also deauthentication and
disassociation). The commands are structured to allow separate
authentication and association steps, i.e., the interface between
kernel and user space is similar to the MLME SAP interface in IEEE
802.11 standard and an user space application takes the role of the
SME.
The patch introduces MLME-AUTHENTICATE.request,
MLME-{,RE}ASSOCIATE.request, MLME-DEAUTHENTICATE.request, and
MLME-DISASSOCIATE.request primitives. The authentication and
association commands request the actual operations in two steps
(assuming the driver supports this; if not, separate authentication
step is skipped; this could end up being a separate "connect"
command).
The initial implementation for mac80211 uses the current
net/mac80211/mlme.c for actual sending and processing of management
frames and the new nl80211 commands will just stop the current state
machine from moving automatically from authentication to association.
Future cleanup may move more of the MLME operations into cfg80211.
The goal of this design is to provide more control of authentication and
association process to user space without having to move the full MLME
implementation. This should be enough to allow IEEE 802.11r FT protocol
and 802.11s SAE authentication to be implemented. Obviously, this will
also bring the extra benefit of not having to use WEXT for association
requests with mac80211. An example implementation of a user space SME
using the new nl80211 commands is available for wpa_supplicant.
This patch is enough to get IEEE 802.11r FT protocol working with
over-the-air mechanism (over-the-DS will need additional MLME
primitives for handling the FT Action frames).
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new nl80211 event notifications (and a new multicast group, "mlme")
for informing user space about received and processed Authentication,
(Re)Association Response, Deauthentication, and Disassociation frames in
station and IBSS modes (i.e., MLME SAP interface primitives
MLME-AUTHENTICATE.confirm, MLME-ASSOCIATE.confirm,
MLME-REASSOCIATE.confirm, MLME-DEAUTHENTICATE.indicate, and
MLME-DISASSOCIATE.indication). The event data is encapsulated as the 802.11
management frame since we already have the frame in that format and it
includes all the needed information.
This is the initial step in providing MLME SAP interface for
authentication and association with nl80211. In other words, kernel code
will act as the MLME and a user space application can control it as the
SME.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We must not clear the previous BSSID when roaming to another AP within
the same ESS for reassociation to be used properly. It is fine to
clear this when the SSID changes, so let's move the code into
ieee80211_sta_set_ssid().
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_tx_h_check_assoc() was dropping everything else than probe
requests during software scan. So the nullfunc frame with the power save
bit was dropped and AP never received it. This meant that AP never
buffered any frames for the station during software scan.
Fix this by allowing to transmit both probe request and nullfunc frames
during software scan. Tested with stlc45xx.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When I added scanning to cfg80211, we got a lock dependency like this:
rtnl --> cfg80211_mtx
nl80211, on the other hand, has the reverse lock dependency:
cfg80211_mtx --> rtnl
which clearly is a bad idea. This patch reworks nl80211 to take these
two locks in the other order to fix the possible, and easily
triggerable, deadlock.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the driver has been notified with a STA_REMOVE, it tears down
the internal ADDBA state. On resume, trying to initiate aggregation would
fail because mac80211 has not cleared the operational state for that <TID,STA>.
This can be fixed by tearing down the existing sessions on a suspend.
Also, the driver can initiate a new BA session when suspend is in progress.
This is fixed by marking the station as being in suspend state and
denying ADDBA requests for such STAs.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To avoid concurrent manipulations of the sta list (which shouldn't
be possible at this point, but anyway) we need to hold the sta_lock
around iterating the list.
At the same time, we do not need to iterate the list at all if
the driver doesn't want to be notified.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes nl80211 export the supported commands (command groups)
per wiphy so userspace has an idea what it can do -- this will be
required reading for userspace when we introduce auth/assoc /or/
connect for older hardware that cannot separate auth and assoc.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Radiotap was updated to include a "bad PLCP" flag and standardise
the "bad FCS" flag in the "flags" rather than "RX flags" field,
this patch updates Linux to that standard.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Even though userland probably cannot submit packets, there might
still be some coming, and that's no good when the driver doesn't
expect them. Stop the queues across suspend/resume.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The last warning can never trigger, and the explicit AP_VLAN
check is pointless if we move the config_interface check down,
in practice config_interface is required anyway.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a scan is queued in STA mode while the interface is in state direct
probe, authenticate or associate the scan is delayed until the interface
enters disabled or associated state. But in case of direct probe-,
authentication- or association- timeout sta_work will not be scheduled
anymore (without external trigger) and thus the pending scan is not
executed and prevents a new scan from being triggered (-EBUSY).
Fix this by queueing the sta work again after direct probe-, authentication-
and association- timeout.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This inline is useless and actually makes the code _longer_
rather than shorter.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The scan capability added to cfg80211/nl80211 introduced a
dependency on nl80211 by cfg80211. We can thus no longer have
just cfg80211 without nl80211. Specifically, cfg80211_scan_done()
calls nl80211_send_scan_aborted() or nl80211_send_scan_done().
Now we remove the option for user to select nl80211. It will always
be compiled if user selects cfg80211.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't call ieee80211_sta_find_ibss() directly, like it's done in STA
mode, so that the commit() call is more harmless respectively has
less site-effects.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Otherwise we can wrap the sizes and end up sending garbage.
Closes#10423
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
spin_lock() should be spin_unlock() in xfrm_state_walk_done().
caused by:
commit 12a169e7d8
"ipsec: Put dumpers on the dump list"
Reported-by: Marc Milgram <mmilgram@redhat.com>
Signed-off-by: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 778d80be52
(ipv6: Add disable_ipv6 sysctl to disable IPv6 operaion on specific interface)
seems to have introduced a leak of sk_buff's for ipv6 traffic,
at least in some configurations where idev is NULL, or when ipv6
is disabled via sysctl.
The problem is that if the first condition of the if-statement
returns non-NULL, it returns an skb with only one reference,
and when the other conditions apply, execution jumps to the "out"
label, which does not call kfree_skb for it.
To plug this leak, change to use the "drop" label instead.
(this relies on it being ok to call kfree_skb on NULL)
This also allows us to avoid calling rcu_read_unlock here,
and removes the only user of the "out" label.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I fixed the GRO crash in the legacy receive path I used
napi_complete to replace __napi_complete. Unfortunately they're
not the same when NETPOLL is enabled, which may result in us
not calling __napi_complete at all.
What's more, we really do need to keep the __napi_complete call
within the IRQ-off section since in theory an IRQ can occur in
between and fill up the backlog to the maximum, causing us to
lock up.
Since we can't seem to find a fix that works properly right now,
this patch reverts all the GRO support from the netif_rx path.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'bkl-removal' of git://git.lwn.net/linux-2.6:
Rationalize fasync return values
Move FASYNC bit handling to f_op->fasync()
Use f_lock to protect f_flags
Rename struct file->f_ep_lock
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (29 commits)
crypto: sha512-s390 - Add missing block size
hwrng: timeriomem - Breaks an allyesconfig build on s390:
nlattr: Fix build error with NET off
crypto: testmgr - add zlib test
crypto: zlib - New zlib crypto module, using pcomp
crypto: testmgr - Add support for the pcomp interface
crypto: compress - Add pcomp interface
netlink: Move netlink attribute parsing support to lib
crypto: Fix dead links
hwrng: timeriomem - New driver
crypto: chainiv - Use kcrypto_wq instead of keventd_wq
crypto: cryptd - Per-CPU thread implementation based on kcrypto_wq
crypto: api - Use dedicated workqueue for crypto subsystem
crypto: testmgr - Test skciphers with no IVs
crypto: aead - Avoid infinite loop when nivaead fails selftest
crypto: skcipher - Avoid infinite loop when cipher fails selftest
crypto: api - Fix crypto_alloc_tfm/create_create_tfm return convention
crypto: api - crypto_alg_mod_lookup either tested or untested
crypto: amcc - Add crypt4xx driver
crypto: ansi_cprng - Add maintainer
...
On a box with most of the optional Netfilter switches turned off some
of the NLAs are never send, e. g. secmark, mark or the conntrack
byte/packet counters. As a worst case scenario this may possibly
still lead to ctnetlink skbs being reallocated in netlink_trim()
later, loosing all the nice effects from the previous patches.
I try to solve that (at least partly) by correctly #ifdef'ing the
NLAs in the computation.
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch renames the ebt_ulog nf_logger from "ulog" to "ebt_ulog" to
be in sync with other modules naming. As this name was currently only
used for informational purpose, the renaming should be harmless.
Signed-off-by: Eric Leblond <eric@inl.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ebt_ulog module does not follow the fixed convention about function
return. Loading the module is triggering the following message:
sys_init_module: 'ebt_ulog'->init suspiciously returned 1, it should follow 0/-E convention
sys_init_module: loading module anyway...
Pid: 2334, comm: modprobe Not tainted 2.6.29-rc5edenwall0-00883-g199e57b #146
Call Trace:
[<c0441b81>] ? printk+0xf/0x16
[<c02311af>] sys_init_module+0x107/0x186
[<c0202cfa>] syscall_call+0x7/0xb
The following patch fixes the return treatment in ebt_ulog_init()
function.
Signed-off-by: Eric Leblond <eric@inl.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the declaration of the logger structure in ebt_log
and ebt_ulog: I forgot to remove the const option from their declaration
in the commit ca735b3aaa ("netfilter:
use a linked list of loggers").
Pointed-out-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Eric Leblond <eric@inl.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes an crash when empty bond device is added to a bridge.
If an interface with invalid ethernet address (all zero) is added
to a bridge, then bridge code detects it when setting up the forward
databas entry. But the error unwind is broken, the bridge port object
can get freed twice: once when ref count went to zeo, and once by kfree.
Since object is never really accessible, just free it.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Usefull for all protocols which do not add additional data, such
as GRE or UDPlite.
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Try to allocate a Netlink skb roughly the size of the actual
message, with the help from the l3 and l4 protocol helpers.
This is all to prevent a reallocation in netlink_trim() later.
The overhead of allocating the right-sized skb is rather small, with
ctnetlink_alloc_skb() actually being inlined away on my x86_64 box.
The size of the per-proto space is determined at registration time of
the protocol helper.
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Use "hlist_nulls" infrastructure we added in 2.6.29 for RCUification of UDP & TCP.
This permits an easy conversion from call_rcu() based hash lists to a
SLAB_DESTROY_BY_RCU one.
Avoiding call_rcu() delay at nf_conn freeing time has numerous gains.
First, it doesnt fill RCU queues (up to 10000 elements per cpu).
This reduces OOM possibility, if queued elements are not taken into account
This reduces latency problems when RCU queue size hits hilimit and triggers
emergency mode.
- It allows fast reuse of just freed elements, permitting better use of
CPU cache.
- We delete rcu_head from "struct nf_conn", shrinking size of this structure
by 8 or 16 bytes.
This patch only takes care of "struct nf_conn".
call_rcu() is still used for less critical conntrack parts, that may
be converted later if necessary.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Commit e1b4b9f ([NETFILTER]: {ip,ip6,arp}_tables: fix exponential worst-case
search for loops) introduced a regression in the loop detection algorithm,
causing sporadic incorrectly detected loops.
When a chain has already been visited during the check, it is treated as
having a standard target containing a RETURN verdict directly at the
beginning in order to not check it again. The real target of the first
rule is then incorrectly treated as STANDARD target and checked not to
contain invalid verdicts.
Fix by making sure the rule does actually contain a standard target.
Based on patch by Francis Dupont <Francis_Dupont@isc.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This is necessary in order to have an upper bound for Netlink
message calculation, which is not a problem at all, as there
are no helpers with a longer name.
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
It calculates the max. length of a Netlink policy, which is usefull
for allocating Netlink buffers roughly the size of the actual
message.
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
There is added a single callback for the l3 proto helper. The two
callbacks for the l4 protos are necessary because of the general
structure of a ctnetlink event, which is in short:
CTA_TUPLE_ORIG
<l3/l4-proto-attributes>
CTA_TUPLE_REPLY
<l3/l4-proto-attributes>
CTA_ID
...
CTA_PROTOINFO
<l4-proto-attributes>
CTA_TUPLE_MASTER
<l3/l4-proto-attributes>
Therefore the formular is
size := sizeof(generic-nlas) + 3 * sizeof(tuple_nlas) + sizeof(protoinfo_nlas)
Some of the NLAs are optional, e. g. CTA_TUPLE_MASTER, which is only
set if it's an expected connection. But the number of optional NLAs is
small enough to prevent netlink_trim() from reallocating if calculated
properly.
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
We use same not trivial helper function in four places. We can factorize it.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Using hlist_add_head() in nf_conntrack_set_hashsize() is quite dangerous.
Without any barrier, one CPU could see a loop while doing its lookup.
Its true new table cannot be seen by another cpu, but previous table is still
readable.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
net/netfilter/xt_LED.c:40: error: field netfilter_led_trigger has incomplete type
net/netfilter/xt_LED.c: In function led_timeout_callback:
net/netfilter/xt_LED.c:78: warning: unused variable ledinternal
net/netfilter/xt_LED.c: In function led_tg_check:
net/netfilter/xt_LED.c:102: error: implicit declaration of function led_trigger_register
net/netfilter/xt_LED.c: In function led_tg_destroy:
net/netfilter/xt_LED.c:135: error: implicit declaration of function led_trigger_unregister
Fix by adding a dependency on LED_TRIGGERS.
Reported-by: Sachin Sant <sachinp@in.ibm.com>
Tested-by: Subrata Modak <tosubrata@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
The ipv6 version of bind_conflict code calls ipv6_rcv_saddr_equal()
which at times wrongly identified intersections between addresses.
It particularly broke down under a few instances and caused erroneous
bind conflicts.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Binding to a v4-mapped address on an AF_INET6 socket should
produce the same result as binding to an IPv4 address on
AF_INET socket. The two are interchangable as v4-mapped
address is really a portability aid.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IPv4 wildcard (0.0.0.0) address does not intersect
in any way with explicit IPv6 addresses. These two should
be permitted, but the IPv4 conflict code checks the ipv6only
bit as part of the test. Since binding to an explicit IPv6
address restricts the socket to only that IPv6 address, the
side-effect is that the socket behaves as v6-only. By
explicitely setting ipv6only in this case, allows the 2 binds
to succeed.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A socket marked v6-only, can not receive or send traffic to v4-mapped
addresses. Thus allowing binding to v4-mapped address on such a
socket makes no sense.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch combines Greg Bank's dprintk() work with the existing dynamic
printk patchset, we are now calling it 'dynamic debug'.
The new feature of this patchset is a richer /debugfs control file interface,
(an example output from my system is at the bottom), which allows fined grained
control over the the debug output. The output can be controlled by function,
file, module, format string, and line number.
for example, enabled all debug messages in module 'nf_conntrack':
echo -n 'module nf_conntrack +p' > /mnt/debugfs/dynamic_debug/control
to disable them:
echo -n 'module nf_conntrack -p' > /mnt/debugfs/dynamic_debug/control
A further explanation can be found in the documentation patch.
Signed-off-by: Greg Banks <gnb@sgi.com>
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
dpm_list currently relies on the fact that child devices will
be registered after their parents to get a correct suspend
order. Using device_move() however destroys this assumption, as
an already registered device may be moved under a newly registered
one.
This patch adds a new argument to device_move(), allowing callers
to specify how dpm_list should be adapted.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the NETLINK_NO_ENOBUFS socket flag. This flag can
be used by unicast and broadcast listeners to avoid receiving
ENOBUFS errors.
Generally speaking, ENOBUFS errors are useful to notify two things
to the listener:
a) You may increase the receiver buffer size via setsockopt().
b) You have lost messages, you may be out of sync.
In some cases, ignoring ENOBUFS errors can be useful. For example:
a) nfnetlink_queue: this subsystem does not have any sort of resync
method and you can decide to ignore ENOBUFS once you have set a
given buffer size.
b) ctnetlink: you can use this together with the socket flag
NETLINK_BROADCAST_SEND_ERROR to stop getting ENOBUFS errors as
you do not need to resync (packets whose event are not delivered
are drop to provide reliable logging and state-synchronization).
Moreover, the use of NETLINK_NO_ENOBUFS also reduces a "go up, go down"
effect in terms of performance which is due to the netlink congestion
control when the listener cannot back off. The effect is the following:
1) throughput rate goes up and netlink messages are inserted in the
receiver buffer.
2) Then, netlink buffer fills and overruns (set on nlk->state bit 0).
3) While the listener empties the receiver buffer, netlink keeps
dropping messages. Thus, throughput goes dramatically down.
4) Then, once the listener has emptied the buffer (nlk->state
bit 0 is set off), goto step 1.
This effect is easy to trigger with netlink broadcast under heavy
load, and it is more noticeable when using a big receiver buffer.
You can find some results in [1] that show this problem.
[1] http://1984.lsi.us.es/linux/netlink/
This patch also includes the use of sk_drop to account the number of
netlink messages drop due to overrun. This value is shown in
/proc/net/netlink.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arches without efficient unaligned access can still perform a loop
assuming 16bit alignment in ifname_compare()
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We use RCU to defer freeing of conntrack structures. In DOS situation, RCU might
accumulate about 10.000 elements per CPU in its internal queues. To get accurate
conntrack counts (at the expense of slightly more RAM used), we might consider
conntrack counter not taking into account "about to be freed elements, waiting
in RCU queues". We thus decrement it in nf_conntrack_free(), not in the RCU
callback.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Tested-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Patrick McHardy <kaber@trash.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (32 commits)
ucc_geth: Fix oops when using fixed-link support
dm9000: locking bugfix
net: update dnet.c for bus_id removal
dnet: DNET should depend on HAS_IOMEM
dca: add missing copyright/license headers
nl80211: Check that function pointer != NULL before using it
sungem: missing net_device_ops
be2net: fix to restore vlan ids into BE2 during a IF DOWN->UP cycle
be2net: replenish when posting to rx-queue is starved in out of mem conditions
bas_gigaset: correctly allocate USB interrupt transfer buffer
smsc911x: reset last known duplex and carrier on open
sh_eth: Fix mistake of the address of SH7763
sh_eth: Change handling of IRQ
netns: oops in ip[6]_frag_reasm incrementing stats
net: kfree(napi->skb) => kfree_skb
net: fix sctp breakage
ipv6: fix display of local and remote sit endpoints
net: Document /proc/sys/net/core/netdev_budget
tulip: fix crash on iface up with shirq debug
virtio_net: Make virtio_net support carrier detection
...
This patch fixes an unaligned memory access in tcp_sack while reading
sequence numbers from TCP selective acknowledgement options. Prior to
applying this patch, upstream linux-2.6.27.20 was occasionally
generating messages like this on my sparc64 system:
[54678.532071] Kernel unaligned access at TPC[6b17d4] tcp_packet+0xcd4/0xd00
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch adds nfnetlink_set_err() to propagate the error to netlink
broadcast listener in case of memory allocation errors in the
message building.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patchs adds support of modification of the used logger via sysctl.
It can be used to change the logger to module that can not use the bind
operation (ipt_LOG and ipt_ULOG). For this purpose, it creates a
directory /proc/sys/net/netfilter/nf_log which contains a file
per-protocol. The content of the file is the name current logger (NONE if
not set) and a logger can be setup by simply echoing its name to the file.
By echoing "NONE" to a /proc/sys/net/netfilter/nf_log/PROTO file, the
logger corresponding to this PROTO is set to NULL.
Signed-off-by: Eric Leblond <eric@inl.fr>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Discard incoming packets whose ack field iincludes data not yet sent.
This is consistent with RFC 793 Section 3.9.
Change tcp_ack() to distinguish between too-small and too-large ack
field values. Keep segments with too-large ack fields out of the fast
path, and change slow path to discard them.
Reported-by: Oliver Zheng <mailinglists+netdev@oliverzheng.com>
Signed-off-by: John Dykstra <john.dykstra1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
