Currently the fact that devlink reload failed is stored in drivers.
Move this flag into devlink core. Also, expose it to the user.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to properly implement failure indication during reload,
split the reload op into two ops, one for down phase and one for
up phase.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split the function restart_one into two functions and separate teardown
and buildup.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to a bug introduced in Linux 3.14 we cannot determine the
correctly layout for a multi-zone RAID0 array - there are two
possibilities.
It is possible to tell the kernel which to chose using a module
parameter, but this can be clumsy to use. It would be best if
the choice were recorded in the metadata.
So add a feature flag for this purpose.
If it is set, then the 'layout' field of the superblock is used
to determine which layout to use.
If this flag is not set, then mddev->layout gets set to -1,
which causes the module parameter to be required.
Acked-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Song Liu <songliubraving@fb.com>
If the drives in a RAID0 are not all the same size, the array is
divided into zones.
The first zone covers all drives, to the size of the smallest.
The second zone covers all drives larger than the smallest, up to
the size of the second smallest - etc.
A change in Linux 3.14 unintentionally changed the layout for the
second and subsequent zones. All the correct data is still stored, but
each chunk may be assigned to a different device than in pre-3.14 kernels.
This can lead to data corruption.
It is not possible to determine what layout to use - it depends which
kernel the data was written by.
So we add a module parameter to allow the old (0) or new (1) layout to be
specified, and refused to assemble an affected array if that parameter is
not set.
Fixes: 20d0189b10 ("block: Introduce new bio_split()")
cc: stable@vger.kernel.org (3.14+)
Acked-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Song Liu <songliubraving@fb.com>
If stripe in batch list is set with STRIPE_HANDLE flag, then the stripe
could be set with STRIPE_ACTIVE by the handle_stripe function. And if
error happens to the batch_head at the same time, break_stripe_batch_list
is called, then below warning could happen (the same report in [1]), it
means a member of batch list was set with STRIPE_ACTIVE.
[7028915.431770] stripe state: 2001
[7028915.431815] ------------[ cut here ]------------
[7028915.431828] WARNING: CPU: 18 PID: 29089 at drivers/md/raid5.c:4614 break_stripe_batch_list+0x203/0x240 [raid456]
[...]
[7028915.431879] CPU: 18 PID: 29089 Comm: kworker/u82:5 Tainted: G O 4.14.86-1-storage #4.14.86-1.2~deb9
[7028915.431881] Hardware name: Supermicro SSG-2028R-ACR24L/X10DRH-iT, BIOS 3.1 06/18/2018
[7028915.431888] Workqueue: raid5wq raid5_do_work [raid456]
[7028915.431890] task: ffff9ab0ef36d7c0 task.stack: ffffb72926f84000
[7028915.431896] RIP: 0010:break_stripe_batch_list+0x203/0x240 [raid456]
[7028915.431898] RSP: 0018:ffffb72926f87ba8 EFLAGS: 00010286
[7028915.431900] RAX: 0000000000000012 RBX: ffff9aaa84a98000 RCX: 0000000000000000
[7028915.431901] RDX: 0000000000000000 RSI: ffff9ab2bfa15458 RDI: ffff9ab2bfa15458
[7028915.431902] RBP: ffff9aaa8fb4e900 R08: 0000000000000001 R09: 0000000000002eb4
[7028915.431903] R10: 00000000ffffffff R11: 0000000000000000 R12: ffff9ab1736f1b00
[7028915.431904] R13: 0000000000000000 R14: ffff9aaa8fb4e900 R15: 0000000000000001
[7028915.431906] FS: 0000000000000000(0000) GS:ffff9ab2bfa00000(0000) knlGS:0000000000000000
[7028915.431907] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[7028915.431908] CR2: 00007ff953b9f5d8 CR3: 0000000bf4009002 CR4: 00000000003606e0
[7028915.431909] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[7028915.431910] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[7028915.431910] Call Trace:
[7028915.431923] handle_stripe+0x8e7/0x2020 [raid456]
[7028915.431930] ? __wake_up_common_lock+0x89/0xc0
[7028915.431935] handle_active_stripes.isra.58+0x35f/0x560 [raid456]
[7028915.431939] raid5_do_work+0xc6/0x1f0 [raid456]
Also commit 59fc630b8b ("RAID5: batch adjacent full stripe write")
said "If a stripe is added to batch list, then only the first stripe
of the list should be put to handle_list and run handle_stripe."
So don't set STRIPE_HANDLE to stripe which is already in batch list,
otherwise the stripe could be put to handle_list and run handle_stripe,
then the above warning could be triggered.
[1]. https://www.spinics.net/lists/raid/msg62552.html
Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
While MD continues to count read errors returned by the lower layer.
If those errors are -EILSEQ, instead of -EIO, it should NOT increase
the read_errors count.
When RAID6 is set up on dm-integrity target that detects massive
corruption, the leg will be ejected from the array. Even if the
issue is correctable with a sector re-write and the array has
necessary redundancy to correct it.
The leg is ejected because it runs up the rdev->read_errors beyond
conf->max_nr_stripes. The return status in dm-drypt when there is
a data integrity error is -EILSEQ (BLK_STS_PROTECTION).
Signed-off-by: Nigel Croxon <ncroxon@redhat.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
A Mediatek based smartphone owner reports problems with USB
tethering in Linux. The verbose USB listing shows a rndis_host
interface pair (e0/01/03 + 10/00/00), but the driver fails to
bind with
[ 355.960428] usb 1-4: bad CDC descriptors
The problem is a failsafe test intended to filter out ACM serial
functions using the same 02/02/ff class/subclass/protocol as RNDIS.
The serial functions are recognized by their non-zero bmCapabilities.
No RNDIS function with non-zero bmCapabilities were known at the time
this failsafe was added. But it turns out that some Wireless class
RNDIS functions are using the bmCapabilities field. These functions
are uniquely identified as RNDIS by their class/subclass/protocol, so
the failing test can safely be disabled. The same applies to the two
types of Misc class RNDIS functions.
Applying the failsafe to Communication class functions only retains
the original functionality, and fixes the problem for the Mediatek based
smartphone.
Tow examples of CDC functional descriptors with non-zero bmCapabilities
from Wireless class RNDIS functions are:
0e8d:000a Mediatek Crosscall Spider X5 3G Phone
CDC Header:
bcdCDC 1.10
CDC ACM:
bmCapabilities 0x0f
connection notifications
sends break
line coding and serial state
get/set/clear comm features
CDC Union:
bMasterInterface 0
bSlaveInterface 1
CDC Call Management:
bmCapabilities 0x03
call management
use DataInterface
bDataInterface 1
and
19d2:1023 ZTE K4201-z
CDC Header:
bcdCDC 1.10
CDC ACM:
bmCapabilities 0x02
line coding and serial state
CDC Call Management:
bmCapabilities 0x03
call management
use DataInterface
bDataInterface 1
CDC Union:
bMasterInterface 0
bSlaveInterface 1
The Mediatek example is believed to apply to most smartphones with
Mediatek firmware. The ZTE example is most likely also part of a larger
family of devices/firmwares.
Suggested-by: Lars Melin <larsm17@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mao Wenan says:
====================
fix memory leak for sctp_do_bind
First two patches are to do cleanup, remove redundant assignment,
and change return type of sctp_get_port_local.
Third patch is to fix memory leak for sctp_do_bind if failed
to bind address.
v2: add one patch to change return type of sctp_get_port_local.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There are more parentheses in if clause when call sctp_get_port_local
in sctp_do_bind, and redundant assignment to 'ret'. This patch is to
do cleanup.
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently sctp_get_port_local() returns a long
which is either 0,1 or a pointer casted to long.
It's neither of the callers use the return value since
commit 62208f1245 ("net: sctp: simplify sctp_get_port").
Now two callers are sctp_get_port and sctp_do_bind,
they actually assumend a casted to an int was the same as
a pointer casted to a long, and they don't save the return
value just check whether it is zero or non-zero, so
it would better change return type from long to int for
sctp_get_port_local.
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable setting skb->mark for UDP and RAW sockets using cmsg.
This is analogous to existing support for TOS, TTL, txtime, etc.
Packet sockets already support this as of commit c7d39e3263
("packet: support per-packet fwmark for af_packet sendmsg").
Similar to other fields, implement by
1. initialize the sockcm_cookie.mark from socket option sk_mark
2. optionally overwrite this in ip_cmsg_send/ip6_datagram_send_ctl
3. initialize inet_cork.mark from sockcm_cookie.mark
4. initialize each (usually just one) skb->mark from inet_cork.mark
Step 1 is handled in one location for most protocols by ipcm_init_sk
as of commit 351782067b ("ipv4: ipcm_cookie initializers").
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ath.git patches for 5.4. Major changes:
wil6210
* add support for Enhanced Directional Multi-Gigabit (EDMG) channels 9-11
* add debugfs file to show PCM ring content
* report boottime_ns in scan results
ath9k
* add a separate loader for AR92XX (and older) pci(e) without eeprom,
enabled with the new ATH9K_PCI_NO_EEPROM Kconfig option
Report chains and chain_signal in ieee80211_rx_status.
It is useful for program such as tcpdump to see if the
antennas are well connected/placed.
8822C is able to receive CCK rates with 2 antennas, while
8822B can only use 1 antenna path to receive CCK rates.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix the wrong RF path for CCK rx power calculation.
Fixes: e3037485c6 ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Tsang-Shian Lin <thlin@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function _rtl92d_evm_db_to_percentage is functionally identical
to the generic version rtl_evm_db_to_percentage, so remove
_rtl92d_evm_db_to_percentage and use the generic version instead.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function _rtl92c_evm_db_to_percentage is functionally identical
to the generic version rtl_evm_db_to_percentage, so remove
_rtl92c_evm_db_to_percentage and use the generic version instead.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function _rtl92c_evm_db_to_percentage is functionally identical
to the generic version rtl_evm_db_to_percentage, so remove
_rtl92c_evm_db_to_percentage and use the generic version instead.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The hardware has enough buffer to receive like 8K for an MPDU.
So tell mac80211 that we can receive AMSDU in AMPDU.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This mechanism reduces the numbers of false alram in cck rate by
dynamically adjusting the value of power threshold and cs_ratio.
We determine the new value by three factors, which are rssi, false alarm
count and igi. Based on these factors, we define the current condition
into five levels. Compared to the previous level, if the level is changed,
we set the new values for power threshold and cs_ratio.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since 8822c requires to do not only IQK, but also DPK.
Move these calibrations that need to be done once the channel
is determined, into phy_calibration.
And note that the order of the calibrations matters, 8822c
should do IQK first, then DPK.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Power amplifiers are not linear components, and require DPK to
reduce its nonlinearity. DPK is called Digital Pre-distortion
Calibration, can be used to compensate the output of power.
DPK tracking is in charge of tracking the thermal changes. And
it then shifts the power curve accordingly, which makes the
power output remains linear even if the PA works in different
temperature.
To perform DPK, the parameter table should also be updated.
And the table will be applied when device is powered on.
Then DPK will reference the values to calibrate.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for doing IQK in firmware
Ideally the RF component's I/Q vectors should be orthogonal,
but usually they are not. So we need to calibrate for the RF
components, ex. PA/LNA, ADC/DAC.
And if the I/Q vectors are more orthogonal, the mixed signal
will have less deviation. This helps with those rates with
higher modulation (MCS8-9), because they have more strict
EVM/SNR requirement. Also the better of the quality of the
signal, the longer it can propagate, and the better throughput
performance we can get.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable 8822C Tx/Rx interrupt migration.
In some platforms, performance test may cause heavy cpu loading and get
bad results. Interrupt migration can decrease the amount of interrupts,
and lower cpu loading.
Signed-off-by: Tsang-Shian Lin <thlin@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
update sequence to v13 to reduce power consumption
when MAC power off
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Each of these drivers defines some device to host macros that are never
used, thus they can be removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In this step, the read/write routines for the descriptors are converted
to use __le32 quantities, thus a lot of casts can be removed. Callback
routines still use the 8-bit arrays, but these are changed within the
specified routine.
The macro that cleared a descriptor has now been converted into an inline
routine.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As a first step in the conversion, the macros that set the RX and TX
descriptors are converted to static inline routines, and the names are
changed from upper to lower case. To minimize the changes in a given
step, the input descriptor information is left as as a byte array
(u8 *), even though it should be a little-endian word array (__le32 *).
That will be changed in the next patch.
Several places where checkpatch.pl complains about a space after a cast
are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver uses a set of local macros to manipulate the RX and TX
descriptors, which are all little-endian quantities. These macros
are replaced by the bitfield macros le32p_replace_bits() and
le32_get_bits(). In several places, the macros operated on an entire
32-bit word. In these cases, a direct read or replacement is used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
iAs the first step in converting from macros that get/set information
in the RX and TX descriptors, unused macros are being removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In this step, the read/write routines for the descriptors are converted
to use __le32 quantities, thus a lot of casts can be removed. Callback
routines still use the 8-bit arrays, but these are changed within the
specified routine.
The macro that cleared a descriptor has now been converted into an inline
routine.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As a first step in the conversion, the macros that set the RX and TX
descriptors are converted to static inline routines, and the names are
changed from upper to lower case. To minimize the changes in a given
step, the input descriptor information is left as as a byte array
(u8 *), even though it should be a little-endian word array (__le32 *).
That will be changed in the next patch.
Several places where checkpatch.pl reports lines too long are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver uses a set of local macros to manipulate the RX and TX
descriptors, which are all little-endian quantities. These macros
are replaced by the bitfield macros le32p_replace_bits() and
le32_get_bits(). In several places, the macros operated on an entire
32-bit word. In these cases, a direct read or replacement is used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As the first step in converting from macros that get/set information
in the RX and TX descriptors, unused macros are being removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With the commit e86dc1ca46 ("Libertas: cfg80211 support") we've lost
the ability to actually set the Mesh SSID from userspace.
NL80211_CMD_SET_INTERFACE with NL80211_ATTR_MESH_ID sets the mesh point
interface's ssid field. Let's use that one for the Libertas Mesh
operation
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Don't populate the array pwr_info_offset on the stack but instead make it
static const. Makes the object code smaller by 207 bytes.
Before:
text data bss dec hex filename
26066 3000 64 29130 71ca drivers/ssb/pci.o
After:
text data bss dec hex filename
25763 3096 64 28923 70fb drivers/ssb/pci.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Michael Büsch <m@bues.ch>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some controllers allow for a one-shot output pulse, in contrast to
periodic output. Now that we have extensible versions of our IOCTLs, we
can finally make use of the 'flags' field to pass a bit telling driver
that if we want one-shot pulse output.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Reviewed-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current version of the IOCTL have a small problem which prevents us
from extending the API by making use of reserved fields. In these new
IOCTLs, we are now making sure that flags and rsv fields are zero which
will allow us to extend the API in the future.
Reviewed-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Port the same fix for ixgbe to ixgbevf.
The ixgbevf driver currently does IPsec Tx offloading
based on an existing secpath. However, the secpath
can also come from the Rx side, in this case it is
misinterpreted for Tx offload and the packets are
dropped with a "bad sa_idx" error. Fix this by using
the xfrm_offload() function to test for Tx offload.
CC: Shannon Nelson <snelson@pensando.io>
Fixes: 7f68d43067 ("ixgbevf: enable VF IPsec offload operations")
Reported-by: Jonathan Tooker <jonathan@reliablehosting.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2019-09-12
This series contains updates to ice driver to implement and support
loading a Dynamic Device Personalization (DDP) package from lib/firmware
onto the device.
Paul updates the way the driver version is stored in the driver so that
we can pass the driver version to the firmware. Passing of the driver
version to the firmware is needed for the DDP package to ensure we have
the appropriate support in the driver for the features in the package.
Lukasz fixes how the firmware version is stored to align with how the
firmware stores its own version. Also extended the log message to
display additional useful information such as NVM version, API patch
information and firmware build hash.
Tony adds the needed driver support to check, load and store the DDP
package. Also add support for the ability to load DDP packages intended
for specific hardware devices, as well as what to do when loading of the
DDP package fails to load.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2019-09-11
This series contains updates to i40e, ixgbe/vf and iavf.
Wenwen Wang fixes a potential memory leak where 3 allocated variables
are not properly cleaned up on failure for ixgbe.
Stefan Assmann fixes a potential kernel panic found when repeatedly
spawning and destroying VFs in i40e when a NULL pointer is dereferenced
due to a race condition. Fixed up the i40e driver to clear the
__I40E_VIRTCHNL_OP_PENDING bit before returning after an invalid
minimum transmit rate is requested. Updates the iavf driver to only
apply the MAC address change when the PF ACK's the requested change.
Tonghao Zhang updates ixgbe to use the skb_get_queue_mapping() API call
instead of the driver accessing the queue mapping directly.
Jake updates i40e to use ktime_get_real_ts64() instead of
ktime_to_timespec64(). Removes the define for bit 0x0001 for cloud
filters, since it is a reserved bit and not a valid type. Also added
code comments to clearly state which bits are reserved and should not be
used or defined for cloud filter adminq command. Clarify the macros
used to specify the cloud filter fields are individual bits, so use the
BIT() macro.
Aleksandr fixes up the print_link_message() to include the "negotiated"
FEC status for i40e.
Czeslaw also adds additional log message for devices without FEC in the
print_link_message() for i40e.
Colin Ian King reduces the object code size by making the array API
static constant.
Magnus fixes a potential receive buffer starvation issue for AF_XDP by
kicking the NAPI context of any queue with an attached AF_XDP zero-copy
socket.
v2: Removed patch 11 from the original series (Alex Duyck's ITR fix),
so that it can be sent to the net tree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel.h macro DIV_ROUND_CLOSEST performs the computation (x + d/2)/d
but is perhaps more readable.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Arrays pwr_info_offset and sprom_sizes can be make static const rather
than populating them on the stack. Shrinks object size by 236 bytes.
Before:
text data bss dec hex filename
11300 1320 64 12684 318c drivers/bcma/sprom.o
After:
text data bss dec hex filename
10904 1480 64 12448 30a0 drivers/bcma/sprom.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The array channel_all can be make static const rather than populating
it on the stack, this makes the code smaller. Also, variable place
is being initialized with a value that is never read, so this assignment
is redundant and can be removed.
Before:
text data bss dec hex filename
118537 9591 0 128128 1f480 realtek/rtlwifi/rtl8821ae/phy.o
After:
text data bss dec hex filename
118331 9687 0 128018 1f412 realtek/rtlwifi/rtl8821ae/phy.o
Saves 110 bytes, (gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Providing a new wiphy on every PCIe reset was confusing and was causing
configuration problems for some users (supplicant and authenticators).
Sticking to the existing wiphy should make error recovery much simpler
and more reliable.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move code allocating/freeing wiphy out of above functions. This will
allow reinitializing the driver (e.g. on some error) without allocating
a new wiphy.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This moves "ops" pointer from "struct brcmf_cfg80211_info" to the
"struct brcmf_pub". This movement makes it possible to allocate wiphy
without attaching cfg80211 (brcmf_cfg80211_attach()). It's required for
later separation of wiphy allocation and driver initialization.
While at it fix also an unlikely memory leak in the brcmf_attach().
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
