Until now only the Exynos SoCs could use the serial driver via the
device tree. This patch adds compatible properties for the other
supported SoCs as well.
Tested on a s3c2416 based machine.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Certain tty line discipline implementations such slip and bluetooth hci invoke
the serial core uart_write() api in their write_wakeup callback. This leads to
a soft lockup with samsung serial driver since the uart port lock is taken in
the driver's interrupt handler and uart_write() attempts to take the same lock
again.
Fix this issue by releasing the uart port lock before the call to
uart_write_wakeup() in the tx handler. Also move the spin-lock/unlock sequence
from s3c64xx_serial_handle_irq() function into the tx and rx irq handlers so
that this change is applicable to s3c24xx platforms as well.
Reported-by: Kyungmin Park <kyungmin.park@samsung.com>
Reported-by: Hyeonkook Kim <hk619.kim@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Cc: Lucas Tavares <lucaskt@linux.vnet.ibm.com>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Tony Prisk <linux@prisktech.co.nz>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Lucas Tavares <lucaskt@linux.vnet.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Tony Prisk <linux@prisktech.co.nz>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert clk_enable/clk_disable to clk_prepare_enable/clk_disable_unprepare
calls as required by common clock framework.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following patch allows users to use KGDB over serial console on
board based on Samsung SOC. It has been tested on a board using
exynos5.
[dianders: changed poll to return NO_POLL_CHAR, which appears to
fix 'help' in kgdb; also updated commit message]
Signed-off-by: Julien Pichon <pichon.jln@gmail.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return the value returned by the failing function instead
of -1 (which does not convey the right error information).
Fixes the following smatch warning:
drivers/tty/serial/samsung.c:1687 s3c24xx_serial_modinit() info:
why not propagate 'ret' from uart_register_driver() instead of -1?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following errors and warnings:
ERROR: trailing whitespace
ERROR: return is not a function, parentheses are not required
WARNING: suspect code indent for conditional statements (32, 36)
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This will let us sort out a whole pile of tty related races. The
alternative would be to keep points and refcount the termios objects.
However
1. They are tiny anyway
2. Many devices don't use the stored copies
3. We can remove a pty special case
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When priting the serial clock source, if clock source name is null,
kernel reference NULL point.
Signed-off-by: KeyYoung Park <keyyoung.park@samsung.com>
Signed-off-by: Huisung Kang <hs1218.kang@samsung.com>
Signed-off-by: Kyoungil Kim <ki0351.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
port->baudclk_rate should be compared to the rate of port->baudclk,
because port->baudclk_rate was assigned as the rate of port->baudclk previously.
So to check that the current baudclk rate is same as previous rate,
the target of comparison sholud be the rate of port->baudclk.
Signed-off-by: Jun-Ho, Yoon <junho78.yoon@samsung.com>
Signed-off-by: Kyoungil Kim <ki0351.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kyoungil Kim <ki0351.kim@samsung.com>
Suggested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix omission initialize ulcon in s3c24xx_serial_resetport(),
reset port function in drivers/tty/serial/samsung.c. It has
been happened from commit 0dfb3b41("serial: samsung: merge
all SoC specific port reset functions")
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: stable <stable@vger.kernel.org> [3.3]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without that fix machines having a s3c2442 CPU have something
like that in dmesg:
samsung-uart s3c2440-uart.0: could not find driver data
samsung-uart s3c2440-uart.1: could not find driver data
samsung-uart s3c2440-uart.2: could not find driver data
And serial is never initialized.
The previous log was obtained trough early printk on the gta02
machine.
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This should be added for EXYNOS4212 and EXYNOS4412 SoCs.
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
exynos4120_serial_drv_data is only defined when building with support
for Exynos4210 so use the already provided define to ensure that we
don't reference it when building for other SoCs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
[kgene.kim@samsung.com: Fixed build warning]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add device tree based discovery support for Samsung's uart controller.
Cc: Ben Dooks <ben-linux@fluff.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
With reset port, set clock and get clock functions in SoC specific extentions
being removed, only the driver probe is left over in these extensions. The
probe function itself can be merged into one and moved into the samsung common
serial driver. With driver probe also moved, all the SoC specific extentions
are no longer required and they are deleted.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The port reset function in each of the platform specific extension performs
the same operations and hence all the reset port functions can be merged into
one and moved into the common samsung uart driver. The SoC specific port reset
functions are removed from SoC extensions.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Instead of using clock names supplied in platform data, use a generic
clock name 'clk_uart_baud' to look up clocks. The platform code should
register clocks with the name 'clk_uart_baud' which can be used by the
baud rate generator. The clock lookup and selection of the best clock
as baud rate clock is reworked.
Platform code can specify the clocks that can be used as source for the
baud clock (as supported previously by passing names of clocks). A new
member is added to the platform data 'clk_sel' which holds a bit-field
value with each bit representing a baud source clock. If a bit at any
bit position is set, that clock is looked up to participate in the
selection of the baud clock source.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
s3c2440 uses fclk/n (fclk divided by n) clock as one of the possible clocks used
to generate the baud rate clock. The divider 'n' in this case can be logically
represented outside of the uart controller.
This patch creates a new clock by name "fclk_n" for s3c2440 based platforms to
represent the fclk/n clock in the platform code. This clock provides a get_rate
callback that checks the UCON0/1/2 registers to determine the clock rate. The
samsung uart driver would receive the "fclk_n" clock name as one of the possible
baud rate clock options and the driver need not determine clock rate of fclk/n.
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add a pointer to the location of the platform data in the driver's private
data. When instantiated using device tree, pdev->dev->platform_data does not
necessarily point to a valid instance of platform data. The platform data
pointer in the driver's private data could be set to pdev->dev->platform_data
or platform data instance created from device tree.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (79 commits)
TTY: serial_core: Fix crash if DCD drop during suspend
tty/serial: atmel_serial: bootconsole removed from auto-enumerates
Revert "TTY: call tty_driver_lookup_tty unconditionally"
tty/serial: atmel_serial: add device tree support
tty/serial: atmel_serial: auto-enumerate ports
tty/serial: atmel_serial: whitespace and braces modifications
tty/serial: atmel_serial: change platform_data variable name
tty/serial: RS485 bindings for device tree
TTY: call tty_driver_lookup_tty unconditionally
TTY: pty, release tty in all ptmx_open fail paths
TTY: make tty_add_file non-failing
TTY: drop driver reference in tty_open fail path
8250_pci: Fix kernel panic when pch_uart is disabled
h8300: drivers/serial/Kconfig was moved
parport_pc: release IO region properly if unsupported ITE887x card is found
tty: Support compat_ioctl get/set termios_locked
hvc_console: display printk messages on console.
TTY: snyclinkmp: forever loop in tx_load_dma_buffer()
tty/n_gsm: avoid fifo overflow in gsm_dlci_data_output
tty/n_gsm: fix a bug in gsm_dlci_data_output (adaption = 2 case)
...
Fix up Conflicts in:
- drivers/tty/serial/8250_pci.c
Trivial conflict with removed duplicate device ID
- drivers/tty/serial/atmel_serial.c
Annoying silly conflict between "specify the port num via
platform_data" and other changes to atmel_console_init
s3c64xx and later SoC's include the interrupt mask and pending registers
in the uart controller, unlike the s3c24xx SoC's which have these registers
in the interrupt controller. When the mask and pending registers are part
of the uart controller, a unified interrupt handler can handle the tx/rx
interrupt. With this, the static reservation of interrupt numbers for the
uart tx/rx/err interrupts in the linux irq space is not required and
simplifies adding device tree support.
Suggested-by: Grant Likely <grant.likely@secretlab.ca>
CC: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (26 commits)
amba pl011: workaround for uart registers lockup
n_gsm: fix the wrong FCS handling
pch_uart: add missing comment about OKI ML7223
pch_uart: Add MSI support
tty: fix "IRQ45: nobody cared"
PTI feature to allow user to name and mark masterchannel request.
0 for o PTI Makefile bug.
tty: serial: samsung.c remove legacy PM code.
SERIAL: SC26xx: Fix link error.
serial: mrst_max3110: initialize waitqueue earlier
mrst_max3110: Change max missing message priority.
tty: s5pv210: Add delay loop on fifo reset function for UART
tty/serial: Fix XSCALE serial ports, e.g. ce4100
serial: bfin_5xx: fix off-by-one with resource size
drivers/tty: use printk_ratelimited() instead of printk_ratelimit()
tty: n_gsm: Added refcount usage to gsm_mux and gsm_dlci structs
tty: n_gsm: Add raw-ip support
tty: n_gsm: expose gsmtty device nodes at ldisc open time
pch_phub: Fix register miss-setting issue
serial: 8250, increase PASS_LIMIT
...
Uart port is registered as a console during the driver's probe.
So explict registration of console with console_initcall is
removed.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
[kgene.kim@samsung.com: removed changes of s3c2400 and s3c24a0]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
In s3c24xx_serial_console_setup function, if the uart port that is
being setup as a console has not been initialized, an error can be
returned instead of using uart port 0 as the default console port.
The uart port that was intended to be used as a console could be
initialized at a later point during boot and then registered as a
console. This will avoid using uart port 0 as a unintended console
port.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch "modernize" tty/serial/samsung.c to use non-legacy code for
suspend/resume.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: KyungMin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
remove invalid location line in each file header after location
moved from driver/char to driver/tty
Signed-off-by: Jovi Zhang <bookjovi@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
tty: update MAINTAINERS file due to driver movement
tty: move drivers/serial/ to drivers/tty/serial/
tty: move hvc drivers to drivers/tty/hvc/
The serial drivers are really just tty drivers, so move them to
drivers/tty/ to make things a bit neater overall.
This is part of the tty/serial driver movement proceedure as proposed by
Arnd Bergmann and approved by everyone involved a number of months ago.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Rogier Wolff <R.E.Wolff@bitwizard.nl>
Cc: Michael H. Warfield <mhw@wittsend.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>