The UFS_RESET macro serves no purpose on QCS404, remove it.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
SAM9X60 uses high and low drive strengths. To implement this, in
at91_pinctrl_mux_ops::set_drivestrength and
at91_pinctrl_mux_ops::get_drivestrength we need bit numbers of
drive strengths (1 for low, 2 for high), thus change the code to
allow the usage of drive strength bit numbers.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds DRIF{0,1,2,3} pins, groups and functions to the R8A77990
SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Select IRQ_DOMAIN_HIERARCHY for spmi-gpio in Kconfig since this driver
is now setup as a hierarchical IRQ chip.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the pinctrl driver support for i.MX8MM.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Acked-by: Aisheng Dong <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In the original code, some function names begin with "ingenic_gpio_",
and some with "gpio_ingenic_". For the sake of uniform style,
all of them are changed to the beginning of "ingenic_gpio_".
Signed-off-by: Zhou Yanjie <zhouyanjie@cduestc.edu.cn>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add mmc2 for JZ4770 and JZ4780:
According to the datasheet, both JZ4770 and JZ4780 have mmc2. But this
part of the original code is missing. It is worth noting that JZ4770's
mmc2 supports 8bit mode while JZ4780's does not, so we added the
corresponding code for both models.
Add nemc-wait for JZ4770 and JZ4780:
Both JZ4770 and JZ4780 have a nemc-wait pin. But this part of the
original code is missing.
Add mac for JZ4770:
JZ4770 have a mac. But this part of the original code is missing.
Signed-off-by: Zhou Yanjie <zhouyanjie@cduestc.edu.cn>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Delete uart4 and i2c3/4 from JZ4770:
According to the datasheet, only JZ4780 have uart4 and i2c3/4. So we
remove it from the JZ4770 code and add a section corresponding the JZ4780.
Fix bugs in i2c0/1:
The pin number was wrong in the original code.
Fix bugs in uart2:
JZ4770 and JZ4780 have different uart2 pins. So the original section JZ4770
has been modified and the corresponding section of JZ4780 has been added.
Fix bugs in mmc0:
JZ4770 and JZ4780 assigned different pins to mmc0's 4~7 data lines. So the
original section JZ4770 has been modified and the corresponding section of
JZ4780 has been added.
Fix bugs in mmc1:
JZ4770's mmc1 has 8bit mode, while JZ4780 doesn't. So the original
section JZ4770 has been modified and the corresponding section of
JZ4780 has been added.
Fix bugs in nemc:
JZ4770's nemc has 16bit mode, while JZ4780 doesn't. So the original section
JZ4770 has been modified and the corresponding section of JZ4780 has been
added. And add missing cs2~5 groups for JZ4770 and JZ4780.
Fix bugs in cim:
JZ4770's cim has 12bit mode, while JZ4780 doesn't. So the original
section JZ4770 has been modified and the corresponding section of
JZ4780 has been added.
Fix bugs in lcd:
Both JZ4770 and JZ4780 lcd should be 24bit instead of 32bit.
Signed-off-by: Zhou Yanjie <zhouyanjie@cduestc.edu.cn>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
So that we could use the generic "pwm" for two or more pins, e.g
pwm0_pmux: pwm0-pmux {
groups = "PWM0", "PWM1";
function = "pwm";
};
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Add TMU pin groups on R-Car E3,
- Miscellaneous fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCXEnXuQAKCRCKwlD9ZEnx
cFJqAP4hmcb8FPI+WYl6S4LCPiEIoh7DyzvMNqaAIapESh2+OgEAuL90j3GPqeBW
zFEqI29YXvMwimZO+1Zsnl3lw8PiNgY=
=2+rG
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v5.1-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v5.1
- Add TMU pin groups on R-Car E3,
- Miscellaneous fixes and cleanups.
There is no need to have the 'sgpio' variable static since new
value always be assigned before use it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The main goal of the change is to remove .pin_config_dbg_parse_modify
callback before a driver with its support appears. So far the in-kernel
interface did not attract any users since its introduction 5 years ago.
Originally .pin_config_dbg_parse_modify callback and the associated
'pinconf-config' debugfs file were introduced in commit f07512e615
("pinctrl/pinconfig: add debug interface"), a short description of
'pinconf-config' usage for debugging can be expressed this way:
Write to 'pinconf-config' (see pinconf_dbg_config_write() function):
% echo -n modify $map_type $device_name $state_name $pin_name $config > \
/sys/kernel/debug/pinctrl/$pinctrl/pinconf-config
It supposes to update a global (therefore single!) 'pinconf_dbg_conf'
variable with an alternative setting, the arguments should match
an existing pinconf device and some registered pinctrl mapping 'map':
* $map_type is either 'config_pin' or 'config_group', it should match
'map->type' value of PIN_MAP_TYPE_CONFIGS_PIN or
PIN_MAP_TYPE_CONFIGS_GROUP accordingly,
* $device_name should match 'map->dev_name' string value,
* $state_name should match 'map->name' string value,
* $pin_name should match 'map->data.configs.group_or_pin' string value,
If all above has matched, then $config is a new value to be set by calling
pinconfops->pin_config_dbg_parse_modify(pctldev, config, matched_config).
After a successful write into 'pinconf-config' a user can read the file
to get information about that single modified pin configuration.
The fact is .pin_config_dbg_parse_modify callback has never been defined
in 'struct pinconf_ops' of any pinconf driver, thus an actual modification
of a pin or group state on any present pinconf controller does not happen,
and it declares that all related code is no more than dead code.
I discovered the issue while attempting to add .pin_config_dbg_parse_modify
support in some drivers and found that too short 'MAX_NAME_LEN' set by
drivers/pinctrl/pinconf.c:372:#define MAX_NAME_LEN 15
is practically insufficient to store a regular pinctrl device name,
which are like 'e6060000.pin-controller-sh-pfc' or pin names like
'MX6QDL_PAD_ENET_REF_CLK', thus it is another indicator that the code
is barely usable, insufficiently tested and unprepossessing.
Of course it might be possible to increase MAX_NAME_LEN, and then add
.pin_config_dbg_parse_modify callbacks to the drivers, but the whole
idea of such a limited debug option looks inviable. A more flexible
way to functionally substitute the original approach is to implicitly
or explicitly use pinctrl_select_state() function whenever needed.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Laurent Meunier <laurent.meunier@st.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The change adds explicit inclusion of linux/pinctrl/machine.h header
to the only needed pinctrl-madera-core.c file, and therefore inclusion
of pinctrl/machine.h header from pinctrl/pinconf.h can be removed.
The change is preparatory to a follow-up reversal of commit f07512e615
("pinctrl/pinconfig: add debug interface").
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
spmi-gpio did not have any irqchip support so consumers of this in
device tree would need to call gpio[d]_to_irq() in order to get the
proper IRQ on the underlying PMIC. IRQ chips in device tree should
be usable from the start without the consumer having to make an
additional call to get the proper IRQ on the parent. This patch adds
hierarchical IRQ chip support to the spmi-gpio code to correct this
issue.
Driver was tested using the volume buttons (via gpio-keys) on the LG
Nexus 5 (hammerhead) phone with the following two configurations.
volume-up {
interrupts-extended = <&pm8941_gpios 2 IRQ_TYPE_EDGE_BOTH>;
...
};
volume-up {
gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
...
};
Both configurations now show that spmi-gpio is the IRQ domain and that
the IRQ is setup in a hierarchy.
$ grep volume_up /proc/interrupts
72: 6 0 spmi-gpio 1 Edge volume_up
$ cat /sys/kernel/debug/irq/irqs/72
handler: handle_edge_irq
device: (null)
status: 0x00000403
_IRQ_NOPROBE
istate: 0x00000000
ddepth: 0
wdepth: 0
dstate: 0x02400203
IRQ_TYPE_EDGE_RISING
IRQ_TYPE_EDGE_FALLING
IRQD_ACTIVATED
IRQD_IRQ_STARTED
node: 0
affinity: 0-3
effectiv:
domain: :soc:spmi@fc4cf000:pm8941@0:gpios@c000
hwirq: 0x1
chip: spmi-gpio
flags: 0x4
IRQCHIP_MASK_ON_SUSPEND
parent:
domain: :soc:spmi@fc4cf000
hwirq: 0xc100057
chip: pmic_arb
flags: 0x4
IRQCHIP_MASK_ON_SUSPEND
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The H6 main pin controller has four banks of interrupt-triggering pins.
The driver as originally submitted only specified three, but had pin
descriptions referencing a fourth bank. This results in a out-of-bounds
access into .irq_array of struct sunxi_pinctrl. This however did not
result in a crash until v4.20, with commit a66d972465 ("devres: Align
data[] to ARCH_KMALLOC_MINALIGN"), which changed the alignment of memory
region returned by devm_kcalloc(). The increase likely moved the
out-of-bounds access into the next, unmapped page.
With KASAN on, the bug is quite clear:
BUG: KASAN: slab-out-of-bounds in sunxi_pinctrl_init_with_variant+0x49c/0x12b8
Write of size 4 at addr ffff80002c680280 by task swapper/0/1
CPU: 2 PID: 1 Comm: swapper/0 Not tainted 5.0.0-rc1-00016-gc480a5e6a077 #3
Hardware name: OrangePi Lite2 (DT)
Call trace:
dump_backtrace+0x0/0x220
show_stack+0x14/0x20
dump_stack+0xac/0xd4
print_address_description+0x60/0x25c
kasan_report+0x14c/0x1ac
__asan_store4+0x80/0xa0
sunxi_pinctrl_init_with_variant+0x49c/0x12b8
h6_pinctrl_probe+0x18/0x20
platform_drv_probe+0x6c/0xc8
really_probe+0x244/0x4b0
driver_probe_device.part.4+0x11c/0x164
__driver_attach+0x120/0x190
bus_for_each_dev+0xe8/0x158
driver_attach+0x30/0x40
bus_add_driver+0x308/0x318
driver_register+0xbc/0x1d0
__platform_driver_register+0x7c/0x88
h6_pinctrl_driver_init+0x18/0x20
do_one_initcall+0xd4/0x208
kernel_init_freeable+0x230/0x2c8
kernel_init+0x10/0x108
ret_from_fork+0x10/0x1c
Allocated by task 1:
kasan_kmalloc.part.0+0x4c/0x100
kasan_kmalloc+0xc4/0xe8
kasan_slab_alloc+0x14/0x20
__kmalloc_track_caller+0x130/0x238
devm_kmalloc+0x34/0xd0
sunxi_pinctrl_init_with_variant+0x1d8/0x12b8
h6_pinctrl_probe+0x18/0x20
platform_drv_probe+0x6c/0xc8
really_probe+0x244/0x4b0
driver_probe_device.part.4+0x11c/0x164
__driver_attach+0x120/0x190
bus_for_each_dev+0xe8/0x158
driver_attach+0x30/0x40
bus_add_driver+0x308/0x318
driver_register+0xbc/0x1d0
__platform_driver_register+0x7c/0x88
h6_pinctrl_driver_init+0x18/0x20
do_one_initcall+0xd4/0x208
kernel_init_freeable+0x230/0x2c8
kernel_init+0x10/0x108
ret_from_fork+0x10/0x1c
Freed by task 0:
(stack is not available)
The buggy address belongs to the object at ffff80002c680080
which belongs to the cache kmalloc-512 of size 512
The buggy address is located 0 bytes to the right of
512-byte region [ffff80002c680080, ffff80002c680280)
The buggy address belongs to the page:
page:ffff7e0000b1a000 count:1 mapcount:0 mapping:ffff80002e00c780 index:0xffff80002c683c80 compound_mapcount: 0
flags: 0x10200(slab|head)
raw: 0000000000010200 ffff80002e003a10 ffff80002e003a10 ffff80002e00c780
raw: ffff80002c683c80 0000000000100001 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff80002c680180: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff80002c680200: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ffff80002c680280: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^
ffff80002c680300: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff80002c680380: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
Correct the number of IRQ banks so there are no more mismatches.
Fixes: c8a8309049 ("pinctrl: sunxi: add support for the Allwinner H6 main pin controller")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On the G12a, there is a new 'region' to handle the drive-strength.
This is optional since the older do not have this.
Fixes: 29ae0952e8 ("pinctrl: meson-g12a: add pinctrl driver support")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since Meson G12A SoC, Introduce new ao registers AO_RTI_PULL_UP_EN_REG
and AO_GPIO_O.
These bits of controlling output level are remapped to the new register
AO_GPIO_O, and the AO_GPIO_O_EN_N support only controlling output enable.
These bits of controlling pull enable are remapped to the new register
AO_RTI_PULL_UP_EN_REG, and the AO_RTI_PULL_UP_REG support only controlling
pull type(up/down).
The new layout of ao gpio/pull registers is as follows:
- AO_GPIO_O_EN_N [offset: 0x9 << 2]
- AO_GPIO_I [offset: 0xa << 2]
- AO_RTI_PULL_UP_REG [offset: 0xb << 2]
- AO_RTI_PULL_UP_EN_REG [offset: 0xc << 2]
- AO_GPIO_O [offset: 0xd << 2]
From above, we can see ao GPIO registers region has been separated by the
ao pull registers. In order to ensure the continuity of the region on
software, the ao GPIO and ao pull registers use the same base address, but
can be identified by the offset.
Fixes: 29ae0952e8 ("pinctrl: meson-g12a: add pinctrl driver support")
Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com>
Signed-off-by: Jianxin Pan <jianxin.pan@amlogic.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Dont print every single iodelay register configuration - this is just
plain noise. Since this is useful debug information, just lower to debug
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Keeping the irq_chip definition static shares it with multiple instances
of the mcp23s08 gpiochip in the system. This is bad and now we get this
warning from gpiolib core:
"detected irqchip that is shared with multiple gpiochips: please fix the
driver."
Hence, move the irq_chip definition from being driver static into the
struct mcp23s08. So a unique irq_chip is used for each gpiochip
instance.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fixes issue created by 9b3e420766.
It wasn't possible for one_regmap_config to be non-NULL at the point
it was tested for mcp23s18 devices.
Applied the same pattern of allocating one_regmap_config using
devm_kmemdump() and then initializing the local regmap structure
from that.
Signed-off-by: Jason Kridner <jdk@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Armada 3700 PCIe IP relies on the pinctrl IP managed by this
driver. For reasons related to the PCI core's organization when
suspending/resuming, PCI host controller drivers must reconfigure
their register at suspend_noirq()/resume_noirq() which happens after
suspend()/suspend_late() and before resume_early()/resume().
In the current state, after resuming from a suspend to RAM cycle the
PCIe IP is reconfigured before the pinctrl one which produces an
interrupt storm. The solution to support PCIe resume operation is to
change the "priority" of this pinctrl driver PM callbacks to
"_noirq()".
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The probing of this driver calls platform_irq_count, which will
setup all of the IRQs that are configured in device tree. In
preparation for converting this driver to be a hierarchical IRQ
chip, hardcode the IRQ count based on the hardware type so that all
the IRQs are not configured immediately and are configured on an
as-needed basis later in the boot process. This change will also
allow for the removal of the interrupts property later in this
patch series once the hierarchical IRQ chip support is in.
This patch also removes the generic qcom,spmi-gpio OF match since we
don't know the number of pins. All of the existing upstream bindings
already include the more-specific binding.
The pm8941 code was tested on a LG Nexus 5 (hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for qcom,pm8005-gpio, qcom,pm8998-gpio, and
qcom,pmi8998-gpio. These three variants are already in use in some
arm64 dtsi files. Those boards work since the generic binding
qcom,spmi-gpio is also specified.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When declaring the HSPI RX1_B and TX1_B pins, two mistakes were made:
- the rows and columns in the BGA pin matrix, from which the pin
numbers are derived, were exchanged,
- it was not taken into account that pin row labelling skips
characters I, O, Q, and S.
Fix the order, and the corresponding pin names.
Notes:
- The actual values of the pin numbers don't really matter (they just
have to be unique), so the wrong order didn't have any impact,
- Changing the names of the pins is user-visible, but there are no
users in (upstream) DTS files.
Fixes: 4f82e3ee72 ("sh-pfc: Support pins not associated with a GPIO port")
Fixes: 09cc76a958 ("sh-pfc: r8a7778: add HSPI pin groups")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds TMU TCLK{1,2} pins, groups and functions to
the R8A77990 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Unlike R-Car M3-W, R-Car M3-N does not have DU_DOTCLKIN2, but the
corresponding pin carries the DU_DOTCLKIN3 signal. Correct all
references to DU_DOTCLKIN2 to fix this.
This change does not have any runtime effect, as it only changes an
internal enum name, and a comment.
Fixes: 490e687eb8 ("pinctrl: sh-pfc: Initial R-Car M3-N support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The naming of the "b" versions of the VIN1 pin groups is a bit odd, in
that the "_b" appears in the middle of the names, instead of as a
suffix.
Increase consistency with other SoCs by making R-Car M2-W and M2-N, and
RZ/G1M and RZ/G1N, use the recently added optional "version" argument of
the VIN_DATA_PIN_GROUP() macro.
Note that this breaks backwards compatibility with existing DTBs, but
there are no upstream users of the "vin1_b_*" names.
Fixes: 8e32c9671f ("pinctrl: sh-pfc: r8a7791: Add VIN pins")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Use union vin_data12 and VIN_DATA_PIN_GROUP() to reduce redundancies in
pin definitions for the VIN1 channel.
This reduces kernel size by 144 bytes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Use union vin_data12 and VIN_DATA_PIN_GROUP() to reduce redundancies in
pin definitions for the VIN0 and VIN1 channels.
This reduces kernel size by 288 bytes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Use union vin_data16 and VIN_DATA_PIN_GROUP() to reduce redundancies in
pin definitions for the VIN5 channel.
This reduces kernel size by 240 bytes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Use union vin_data16 and VIN_DATA_PIN_GROUP() to reduce redundancies in
pin definitions for the VIN5 channel.
This reduces kernel size by 240 bytes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Documentation for ES1.0 says that some bits in TDSEL must be set (ch
5.3.35 in R-Car E2 v0.5). However, the reset value of the register is 0,
so software has to do it. Add this to the kernel driver to ensure this
is really done independent of firmware versions and use whitelisting for
ES versions known to need this.
This is needed for some SD cards supporting SDR104 transfer mode.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Documentation for ES1.0 says that some bits in TDSEL must be set (ch
5.3.39 in R-Car H2 v0.91). However, the reset value of the register is
0, so software has to do it. Add this to the kernel driver to ensure
this is really done independent of firmware versions and use
whitelisting for ES versions known to need this.
This is needed for some SD cards supporting SDR104 transfer mode. For
me, TDSEL was not initialized by the firmware and I had problems with
the card when re-inserting it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Knowing which pin group is being configured is useful information when
debugging pin configuration.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
This reverts commit f4caa6ee73.
The same can be expressed better by dropping the
SH_PFC_PIN_CFG_PULL_DOWN flag from the GPIO description, as it includes
returning an error to the caller when trying to configure the pin for
pull-down, causing:
sh-pfc e6060000.pin-controller: pin_config_set op failed for pin 201
sh-pfc e6060000.pin-controller: Error applying setting, reverse things back
sh-pfc e6060000.pin-controller: failed to select default state
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
MOD_SEL register bit numbering was different from R-Car D3 SoC and
R-Car H3/M3-[WN] SoCs.
MOD_SEL 1-bit H3/M3-[WN] D3
=============== ========== =====
Set Value = H'0 b'0 b'0
Set Value = H'1 b'1 b'1
MOD_SEL 2-bits H3/M3-[WN] D3
=============== ========== =====
Set Value = H'0 b'00 b'00
Set Value = H'1 b'01 b'10
Set Value = H'2 b'10 b'01
Set Value = H'3 b'11 b'11
MOD_SEL 3-bits H3/M3-[WN] D3
=============== ========== =====
Set Value = H'0 b'000 b'000
Set Value = H'1 b'001 b'100
Set Value = H'2 b'010 b'010
Set Value = H'3 b'011 b'110
Set Value = H'4 b'100 b'001
Set Value = H'5 b'101 b'101
Set Value = H'6 b'110 b'011
Set Value = H'7 b'111 b'111
This patch replaces the #define name and value of MOD_SEL.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Fixes: 794a671176 ("pinctrl: sh-pfc: Initial R8A77995 PFC support")
[shimoda: split a patch per SoC and revise the commit log]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
[geert: Use a macro to do the actual reordering]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
MOD_SEL register bit numbering was different from R-Car E3 SoC and
R-Car H3/M3-[WN] SoCs.
MOD_SEL 1-bit H3/M3-[WN] E3
=============== ========== =====
Set Value = H'0 b'0 b'0
Set Value = H'1 b'1 b'1
MOD_SEL 2-bits H3/M3-[WN] E3
=============== ========== =====
Set Value = H'0 b'00 b'00
Set Value = H'1 b'01 b'10
Set Value = H'2 b'10 b'01
Set Value = H'3 b'11 b'11
MOD_SEL 3-bits H3/M3-[WN] E3
=============== ========== =====
Set Value = H'0 b'000 b'000
Set Value = H'1 b'001 b'100
Set Value = H'2 b'010 b'010
Set Value = H'3 b'011 b'110
Set Value = H'4 b'100 b'001
Set Value = H'5 b'101 b'101
Set Value = H'6 b'110 b'011
Set Value = H'7 b'111 b'111
This patch replaces the #define name and value of MOD_SEL.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Fixes: 6d4036a1e3 ("pinctrl: sh-pfc: Initial R8A77990 PFC support")
[shimoda: Split a patch per SoC and revise the commit log]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
[geert: Use macros to do the actual reordering]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of
Aug 24, 2018, the MOD_SEL0 bit2 is set when RX2_{A,B}, TX2_{A,B} and
SCK2_A pin functions are selected.
Fixes: 6d4036a1e3 ("pinctrl: sh-pfc: Initial R8A77990 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of
Aug 24, 2018, the MOD_SEL0 bit3 is set to 0 when TX0_A pin function is
selected, and the MOD_SEL0 bit3 is set to 1 when TX0_B pin function is
selected.
Fixes: 6d4036a1e3 ("pinctrl: sh-pfc: Initial R8A77990 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Well, hopefully 3rd time is a charm. We tried making that check
DMI_BIOS_VERSION and DMI_BOARD_VERSION, but the real one is
DMI_PRODUCT_VERSION.
Fixes: 86c5dd6860 ("pinctrl: cherryview: limit Strago DMI workarounds to version 1.0")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=197953
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1631930
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On most newer Allwinner SoCs, there are two pinctrl devices, the PIO and
R_PIO. PIO covers pin-banks PA to PI (PJ and PK have not been seen),
while R_PIO covers PL to PN. The regulator array only has space for 12
entries, which was designed to cover PA to PL. On the A80, the pin banks
go up to PN, which would be the 14th entry in the regulator array.
However since the driver only needs to track regulators for its own pin
banks, the array only needs to have 9 entries, and also take in to
account the value of pin_base, such that the regulator for the first
pin-bank of the pinctrl device, be it "PA" or "PL" uses the first entry
of the array.
Base the regulator array index on pin_base, such that "PA" for PIO and
"PL" for R_PIO both take the first element within their respective
device's regulator array.
Also decrease the size of the regulator array to 9, just enough to cover
"PA" to "PI".
Fixes: 9a2a566adb ("pinctrl: sunxi: Deal with per-bank regulators")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The new per-pin-bank regulator handling code in the sunxi pinctrl driver
has mismatched conditions for enabling and disabling the regulator: it
is enabled each time a pin is requested, but only disabled when the
pin-bank's reference count reaches zero.
Since we are doing reference counting already, there's no need to enable
the regulator each time a pin is requested. Instead we can just do it
for the first requested pin of each pin-bank. Thus we can reverse the
test and bail out early if it's not the first occurrence.
Fixes: 9a2a566adb ("pinctrl: sunxi: Deal with per-bank regulators")
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Gigabit Ethernet requires the Ethernet TXD0..3 and RXD0..3 data lines.
Add the missing eth_rxd2 and eth_rxd3 definitions so we don't have to
rely on the bootloader to set them up correctly.
The vendor u-boot sources for Odroid-C1 use the following Ethernet
pinmux configuration:
SET_CBUS_REG_MASK(PERIPHS_PIN_MUX_6, 0x3f4f);
SET_CBUS_REG_MASK(PERIPHS_PIN_MUX_7, 0xf00000);
This translates to the following pin groups in the mainline kernel:
- register 6 bit 0: eth_rxd1 (DIF_0_P)
- register 6 bit 1: eth_rxd0 (DIF_0_N)
- register 6 bit 2: eth_rx_dv (DIF_1_P)
- register 6 bit 3: eth_rx_clk (DIF_1_N)
- register 6 bit 6: eth_tx_en (DIF_3_P)
- register 6 bit 8: eth_ref_clk (DIF_3_N)
- register 6 bit 9: eth_mdc (DIF_4_P)
- register 6 bit 10: eth_mdio_en (DIF_4_N)
- register 6 bit 11: eth_tx_clk (GPIOH_9)
- register 6 bit 12: eth_txd2 (GPIOH_8)
- register 6 bit 13: eth_txd3 (GPIOH_7)
- register 7 bit 20: eth_txd0_0 (GPIOH_6)
- register 7 bit 21: eth_txd1_0 (GPIOH_5)
- register 7 bit 22: eth_rxd3 (DIF_2_P)
- register 7 bit 23: eth_rxd2 (DIF_2_N)
All functions except eth_rxd2 and eth_rxd3 are already supported by the
pinctrl-meson8b driver.
Suggested-by: Jianxin Pan <jianxin.pan@amlogic.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Reviewed-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
on i386 or x86_64:
Lots of build errors for drivers/pinctrl/mediatek/pinctrl-moore.c when
CONFIG_OF is not enabled (but COMPILE_TEST is).
first this:
WARNING: unmet direct dependencies detected for PINCTRL_MTK_MOORE
Depends on [n]: PINCTRL [=y] && (ARCH_MEDIATEK || COMPILE_TEST [=y])
&& OF [=n]
Selected by [y]:
- PINCTRL_MT7623 [=y] && PINCTRL [=y] &&
(ARCH_MEDIATEK || COMPILE_TEST [=y]) && (MACH_MT7623 || COMPILE_TEST [=y])
and then:
../drivers/pinctrl/mediatek/pinctrl-moore.c:22:44: error: array type has
incomplete element type
static const struct pinconf_generic_params mtk_custom_bindings[] = {
(etc)
Fixes: b5af33df50 ("pinctrl: mediatek: improve Kconfig dependencies")
Cc: stable@vger.kernel.org
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = devm_kzalloc(dev, sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = devm_kzalloc(dev, struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = devm_kzalloc(dev, sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = devm_kzalloc(dev, struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Virtual gpio only used inside SOC and not being exported to outside SOC.
Some modules use virtual gpio as eint and doesn't need SMT.
So this patch add EINT support to virtual GPIOs.
Signed-off-by: Chuanjia Liu <Chuanjia.Liu@mediatek.com>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is a cleanup and fix of the patch by Ken Ma <make@marvell.com>.
Fix the mpp definitions according to newest revision of the
specification:
- northbridge:
fix pmic1 gpio number to 7
fix pmic0 gpio number to 6
- southbridge
split pcie1 group bit mask to BIT(5) and BIT(9)
fix ptp group bit mask to BIT(11) | BIT(12) | BIT(13)
add smi group with bit mask BIT(4)
[gregory: split the pcie group in 2, as at hardware level they can be
configured separately]
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Tested-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
MX8QM contains a system controller that is responsible for controlling
the pad setting of the IPs that are present. Communication between the
host processor running an OS and the system controller happens through
a SCU protocol. This patch adds the SCU based MX8QM pinctrl driver.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
No core changes this time.
New drivers:
- NXP (ex Freescale) i.MX 8 QXP SoC driver.
- Mediatek MT6797 SoC driver.
- Mediatek MT7629 SoC driver.
- Actions Semiconductor S700 SoC driver.
- Renesas RZ/A2 SoC driver.
- Allwinner sunxi suniv F1C100 SoC driver.
- Qualcomm PMS405 PMIC driver.
- Microsemi Ocelot Jaguar2 SoC driver.
Improvements:
- Some RT improvements (using raw spinlocks where appropriate).
- A lot of new pin sets on the Renesas PFC pin controllers.
- GPIO hogs now work on the Qualcomm SPMI/SSBI pin controller GPIO
chips, and Xway.
- Major modernization of the Intel pin control drivers.
- STM32 pin control driver will now synchronize usage of pins
with another CPU using a hardware spinlock.
-----BEGIN PGP SIGNATURE-----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=cm6m
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"We have no core changes but lots of incremental development in drivers
all over the place: Renesas, NXP, Mediatek and Actions Semiconductor
keep churning out new SoCs.
I have some subtree maintainers for Renesas and Intel helping out to
keep down the load, it's been working smoothly (Samsung also have a
subtree but it was not used this cycle.)
New drivers:
- NXP (ex Freescale) i.MX 8 QXP SoC driver.
- Mediatek MT6797 SoC driver.
- Mediatek MT7629 SoC driver.
- Actions Semiconductor S700 SoC driver.
- Renesas RZ/A2 SoC driver.
- Allwinner sunxi suniv F1C100 SoC driver.
- Qualcomm PMS405 PMIC driver.
- Microsemi Ocelot Jaguar2 SoC driver.
Improvements:
- Some RT improvements (using raw spinlocks where appropriate).
- A lot of new pin sets on the Renesas PFC pin controllers.
- GPIO hogs now work on the Qualcomm SPMI/SSBI pin controller GPIO
chips, and Xway.
- Major modernization of the Intel pin control drivers.
- STM32 pin control driver will now synchronize usage of pins with
another CPU using a hardware spinlock"
* tag 'pinctrl-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (145 commits)
dt-bindings: arm: fsl-scu: add imx8qm pinctrl support
pinctrl: freescale: Break dependency on SOC_IMX8MQ for i.MX8MQ
pinctrl: imx-scu: Depend on IMX_SCU
pinctrl: ocelot: Add dependency on HAS_IOMEM
pinctrl: ocelot: add MSCC Jaguar2 support
pinctrl: bcm: ns: support updated DT binding as syscon subnode
dt-bindings: pinctrl: bcm4708-pinmux: rework binding to use syscon
MAINTAINERS: merge at91 pinctrl entries
pinctrl: imx8qxp: break the dependency on SOC_IMX8QXP
pinctrl: uniphier: constify uniphier_pinctrl_socdata
pinctrl: mediatek: improve Kconfig dependencies
pinctrl: msm: mark PM functions as __maybe_unused
dt-bindings: pinctrl: sunxi: Add supply properties
pinctrl: meson: meson8b: add the missing GPIO_GROUPs for BOOT and CARD
pinctrl: meson: meson8: add the missing GPIO_GROUPs for BOOT and CARD
pinctrl: meson: meson8: rename the "gpio" function to "gpio_periphs"
pinctrl: meson: meson8: rename the "gpio" function to "gpio_periphs"
pinctrl: meson: meson8b: fix the GPIO function for the GPIOAO pins
pinctrl: meson: meson8: fix the GPIO function for the GPIOAO pins
pinctrl: sh-pfc: Make pinmux_cfg_reg.var_field_width[] variable-length
...
The CONFIG_SOC_IMX8MQ will go away, so the dependency can be based on
ARCH_MXC && ARM64.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Otherwise building fails with only PINCTRL_IMX_SCU selected:
aarch64-linux-gnu-ld: drivers/pinctrl/freescale/pinctrl-scu.o: in function `imx_pinctrl_sc_ipc_init':
pinctrl-scu.c:(.text+0x10): undefined reference to `imx_scu_get_handle'
aarch64-linux-gnu-ld: pinctrl-scu.c:(.text+0x10): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `imx_scu_get_handle'
aarch64-linux-gnu-ld: drivers/pinctrl/freescale/pinctrl-scu.o: in function `imx_pinconf_get_scu':
pinctrl-scu.c:(.text+0x64): undefined reference to `imx_scu_call_rpc'
aarch64-linux-gnu-ld: pinctrl-scu.c:(.text+0x64): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `imx_scu_call_rpc'
aarch64-linux-gnu-ld: drivers/pinctrl/freescale/pinctrl-scu.o: in function `imx_pinconf_set_scu':
pinctrl-scu.c:(.text+0x104): undefined reference to `imx_scu_call_rpc'
aarch64-linux-gnu-ld: pinctrl-scu.c:(.text+0x104): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `imx_scu_call_rpc'
make: *** [Makefile:1038: vmlinux] Error 1
Signed-off-by: Guido Günther <agx@sigxcpu.or>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As usual the build fails on UM Linux because that thing does
not have IOMEM. Depend on HAS_IOMEM solves the build problem.
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Jaguar2 has the same register layout as Ocelot but it has 64 pins, meaning
that there are 2 registers instead of one.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Documentation has been recently updated specifying that pinctrl should
be subnode of the CRU "syscon". Support that by using parent node for
regmap and reading "offset" property from the DT.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ARM64 SoC does not encourage people to add more finegrained SoC
config options rather than a single ARCH_<family> in arch Kconfig.
So this patch aims to break the dependency on SOC_IMX8QXP.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove prompts to make all pinctrl cores to non-visible symbols and
make sure the target SoCs would be coupled with the corresponding
cores.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com
Acked-by: Sean Wang <sean.wang@kernel.org>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Without CONFIG_PM_SLEEP, we get annoying warnings about unused functions:
drivers/pinctrl/qcom/pinctrl-msm.c:1082:12: error: 'msm_pinctrl_resume' defined but not used [-Werror=unused-function]
static int msm_pinctrl_resume(struct device *dev)
^~~~~~~~~~~~~~~~~~
drivers/pinctrl/qcom/pinctrl-msm.c:1075:12: error: 'msm_pinctrl_suspend' defined but not used [-Werror=unused-function]
static int msm_pinctrl_suspend(struct device *dev)
Mark them as __maybe_unused to shut up the warning and silently drop
the functions without having to add ugly #ifdefs.
Fixes: 977d057ad3 ("pinctrl: msm: Add sleep pinctrl state transitions")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the BOOT and CARD pins as GROUP_GROUPs as well so they can be
configured in devicetree using groups = BOOTx or groups = CARDx. This
makes the behavior consistent with other pins inside the same driver as
well as with the BOOT and CARD pins of the GXBB and GXL pinctrl drivers.
Fixes: 0fefcb6876 ("pinctrl: Add support for Meson8b")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the BOOT and CARD pins as GROUP_GROUPs as well so they can be
configured in devicetree using groups = BOOTx or groups = CARDx. This
makes the behavior consistent with other pins inside the same driver as
well as with the BOOT and CARD pins of the GXBB and GXL pinctrl drivers.
Fixes: 6ac7309511 ("pinctrl: add driver for Amlogic Meson SoCs")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rename the existing "gpio" function to "gpio_periphs". This makes it
consistent with the "gpio_aobus" function. Also GXBB and GXL are also
using the "gpio_periphs" naming, so this makes the code here consistent
with other Amlogic pinctrl drivers.
No functional changes since thee "gpio" function is currently not used.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rename the existing "gpio" function to "gpio_periphs". This makes it
consistent with the "gpio_aobus" function. Also GXBB and GXL are also
using the "gpio_periphs" naming, so this makes the code here consistent
with other Amlogic pinctrl drivers.
No functional changes since thee "gpio" function is currently not used.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIOAO pins (as well as the two exotic GPIO_BSD_EN and GPIO_TEST_N)
only belong to the pin controller in the AO domain. With the current
definition these pins cannot be referred to in .dts files as group
(which is possible on GXBB and GXL for example).
Add a separate "gpio_aobus" function to fix the mapping between the pin
controller and the GPIO pins in the AO domain. This is similar to how
the GXBB and GXL drivers implement this functionality.
Fixes: 9dab1868ec ("pinctrl: amlogic: Make driver independent from two-domain configuration")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIOAO pins (as well as the two exotic GPIO_BSD_EN and GPIO_TEST_N)
only belong to the pin controller in the AO domain. With the current
definition these pins cannot be referred to in .dts files as group
(which is possible on GXBB and GXL for example).
Add a separate "gpio_aobus" function to fix the mapping between the pin
controller and the GPIO pins in the AO domain. This is similar to how
the GXBB and GXL drivers implement this functionality.
Fixes: 9dab1868ec ("pinctrl: amlogic: Make driver independent from two-domain configuration")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinmux_cfg_reg.var_field_width[] is actually a variable-length array,
terminated by a zero, and counting at most r_width entries.
Usually the number of entries is much smaller than r_width, so the
ability to catch bugs at compile time through an "excess elements in
array initializer" warning is fairly limited.
Hence make the array variable-length, decreasing kernel size slightly.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The debug code in sh_pfc_write_config_reg() prints the width of the
field being modified.
However, registers with a variable-width field layout are identified by
pinmux_cfg_reg.field_width being zero, hence zeroes are printed instead
of the actual field widths.
Fix this by printing the Hamming weight of the field mask instead, which
is correct for both fixed-width and variable-width fields.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Some values in the Peripheral Function Select Register 10 descriptor are
shifted by one position, which may cause a peripheral function to be
programmed incorrectly.
Fixing this makes all HSCIF0 pins use Function 4 (value 3), like was
already the case for the HSCK0 pin in field IP10[5:3].
Fixes: ac1ebc2190 ("sh-pfc: Add sh7734 pinmux support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The IP10[5:3] field in Peripheral Function Select Register 10 has a
width of 3 bits, i.e. it allows programming one out of 8 different
configurations.
However, 9 values are provided instead of 8, overflowing into the
subsequent field in the register, and thus breaking the configuration of
the latter.
Fix this by dropping a bogus zero value.
Fixes: ac1ebc2190 ("sh-pfc: Add sh7734 pinmux support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The Port C I/O Register 0 contains 7 reserved bits, but the descriptor
contains only dummy configuration values for 6 reserved bits, thus
breaking the configuration of all subsequent fields in the register.
Fix this by adding the two missing configuration values.
Fixes: f5e811f2a4 ("sh-pfc: Add sh7269 pinmux support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The Port F Control Register 3 (PFCR3) contains only a single field.
However, counting from left to right, it is the fourth field, not the
first field.
Insert the missing dummy configuration values (3 fields of 16 values) to
fix this.
The descriptor for the Port F Control Register 0 (PFCR0) lacks the
description for the 4th field (PF0 Mode, PF0MD[2:0]).
Add the missing configuration values to fix this.
Fixes: a8d42fc421 ("sh-pfc: Add sh7264 pinmux support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
While the SEL_PWM[0-3] fields in the Module Select Register 0 support 4
possible configurations per PWM pin, only the first 3 are valid.
Replace the invalid and unused configurations for SEL_PWM[0-3]_3 by
dummies.
Fixes: 794a671176 ("pinctrl: sh-pfc: Initial R8A77995 PFC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The SEL_I2C1 (MOD_SEL0[21:20]) field in Module Select Register 0 has a
width of 2 bits, i.e. it allows programming one out of 4 different
configurations.
However, the MOD_SEL0_21_20 macro contains 8 values instead of 4,
overflowing into the subsequent fields in the register, and thus breaking
the configuration of the latter.
Fix this by dropping the bogus last 4 values, including the non-existent
SEL_I2C1_4 configuration.
Fixes: 6d4036a1e3 ("pinctrl: sh-pfc: Initial R8A77990 PFC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The Peripheral Function Select Register 11 contains 3 reserved bits and
15 variable-width fields, but the variable field descriptor does not
contain the 3-bit field IP11[25:23].
Fixes: 856cb4bb33 ("sh: Add support pinmux for SH7734")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The Module Select Register 0 contains 20 (= 5 x 4) reserved bits, and 12
single-bit fields, but the variable field descriptor lacks a field of 4
reserved bits.
Fixes: f59125248a ("pinctrl: sh-pfc: Add R8A77980 PFC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The Module Select Register 0 contains 20 (= 5 x 4) reserved bits, and 12
single-bit fields, but the variable field descriptor lacks a field of 4
reserved bits.
Fixes: b92ac66a18 ("pinctrl: sh-pfc: Add R8A77970 PFC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The Peripheral Function Select Register 9 contains 12 fields, but the
variable field descriptor contains a 13th bogus field of 3 bits.
Fixes: 43c4436e2f ("pinctrl: sh-pfc: add R8A7794 PFC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Add a build-time check, to ensure the number of pins and pin marks in a
pin group matches. This helps catching bugs early.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The tpu4_to3_mux[] array contains the TPU4TO3 pin mark, but the
tpu4_to3_pins[] array lacks the corresponding pin number.
Add the missing pin number, for non-GPIO pin F26.
Fixes: 5da4eb049d ("sh-pfc: sh73a0: Add TPU pin groups and functions")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The vin1_b_data18_mux[] arrays contains pin marks for the 2 LSB bits of
the color components. The vin1_b_data18_pins[] array rightfully does
not include the corresponding pin numbers, as RGB18 is subset of RGB24,
containing only the 6 MSB bits of each component.
Fixes: 8e32c9671f ("pinctrl: sh-pfc: r8a7791: Add VIN pins")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The qspi_data4_b_mux[] array contains pin marks for the clock and chip
select pins. The qspi_data4_b_pins[] array rightfully does not contain
the corresponding pin numbers, as the control pins are provided by a
separate group (qspi_ctrl_b).
Fixes: 2d0c386f13 ("pinctrl: sh-pfc: r8a7791: Add QSPI pin groups")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The lcd0_data24_1_pins[] array contains the LCD0 D1[2-5] pin numbers,
but the lcd0_data24_1_mux[] array lacks the corresponding pin marks.
Fixes: 06c7dd866d ("sh-pfc: r8a7740: Add LCDC0 and LCDC1 pin groups and functions")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The gether_gmii_mux[] array contains the REF125CK pin mark, but the
gether_gmii_pins[] array lacks the corresponding pin number.
Fixes: bae11d30d0 ("sh-pfc: r8a7740: Add GETHER pin groups and functions")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Due to an interaction with commit 9f2b76a2db ("pinctrl: sh-pfc:
r8a77990: Add R8A774C0 PFC support"), the state of the I/O Control
Registers is saved/restored during s2ram on RZ/G2E, but not on R-Car E3.
Hence on R-Car E3, SDHI voltage state is lost after system resume.
Fix this by registering the I/O Control Registers on R-Car E3, too.
Fixes: 33847a7137 ("pinctrl: sh-pfc: r8a77990: Add voltage switch operations for SDHI")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
devm_kasprintf() may return NULL on failure of internal allocation
thus the assignments are not safe if not checked. On error
rza1_pinctrl_register() respectively rza1_parse_gpiochip() return
negative values so -ENOMEM in the (unlikely) failure case of
devm_kasprintf() should be fine here.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: 5a49b644b3 ("pinctrl: Renesas RZ/A1 pin and gpio controller")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The R-Car Gen3 HardWare Manual Errata for Rev. 1.00 (Jul 2, 2018) states
that the USB30_OVC pin supports pull-up only. It has a bit assigned in
the pull-enable register (PUEN5), but not in the pull-up/down control
register (PUD5).
Add a check for this, to prevent configuring a prohibited setting.
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Fixes: 83f6941a42 ("pinctrl: sh-pfc: r8a77990: Add bias pinconf support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
This patch is based on commit a86caa9ba5 ("pinctrl: msm: fix gpio-hog
related boot issues").
It fixes the issue that the gpio ranges needs to be defined before
gpiochip_add().
Therefore, we also have to swap the order of registering the pinctrl
driver and registering the gpio chip.
You also have to add the "gpio-ranges" property to the pinctrl device
node to get it finally working.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Clang does not support this option:
warning: unknown warning option '-Woverride-init'; did you mean
'-Woverride-module'? [-Wunknown-warning-option]
1 warning generated.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Allwinner SoCs have on most of their GPIO banks a regulator input.
This issue was mainly ignored so far because either the regulator was a
static regulator that would be providing power anyway, or the bank was used
for a feature unsupported so far (CSI). For the odd cases, enabling it in
the bootloader was the preferred option.
However, now that we are starting to support those features, and that we
can't really rely on the bootloader for this, we need to model those
regulators as such in the DT.
This is slightly more complicated than what it looks like, since some
regulators will be tied to the PMIC, and in order to have access to the
PMIC bus, you need to mux its pins, which will need the pinctrl driver,
that needs the regulator driver to be registered. And this is how you get a
circular dependency.
In practice however, the hardware cannot fall into this case since it would
result in a completely unusable bus. In order to avoid that circular
dependency, we can thus get and enable the regulators at pin_request time.
We'll then need to account for the references of all the pins of a
particular branch to know when to put the reference, but it works pretty
nicely once implemented.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Convert string compares of DT node names to use of_node_name_eq helper
instead. This removes direct access to the node name pointer.
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Tomasz Figa <tomasz.figa@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Switch to generic ->probe() callbacks.
Simplify getting .driver_data.
Code formatting fixes and headers clean up.
Special case is the driver for Intel Cherryview SoC, where GPIO enabling bit
was mistakenly cleared when pin gets freed. It's fixed now.
The below commit went to v4.20-rc3, that's why duplication.
- ad774315c3 MAINTAINERS: Add tree link for Intel pin control driver
The following is an automated git shortlog grouped by driver:
baytrail:
- Code formatting fixes
- simplify getting .driver_data
broxton:
- Code formatting fixes
- Get rid of unneeded ->probe() stub
cannonlake:
- Code formatting fixes
- Get rid of unneeded ->probe() stub
cedarfork:
- Replace acpi.h with mod_devicetable.h
- Get rid of unneeded ->probe() stub
cherryview:
- Stop clearing the GPIO_EN bit from chv_gpio_disable_free
- Add chv_gpio_clear_triggering() helper function
- simplify getting .driver_data
denverton:
- Replace acpi.h with mod_devicetable.h
- Get rid of unneeded ->probe() stub
geminilake:
- Code formatting fixes
icelake:
- Code formatting fixes
- Get rid of unneeded ->probe() stub
intel:
- Unexport intel_pinctrl_probe()
- simplify getting .driver_data
lewisburg:
- Replace acpi.h with mod_devicetable.h
- Get rid of unneeded ->probe() stub
MAINTAINERS:
- Add tree link for Intel pin control driver
merrifield:
- include bits.h instead of bitops.h
sunrisepoint:
- Get rid of unneeded ->probe() stub
-----BEGIN PGP SIGNATURE-----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=3yX5
-----END PGP SIGNATURE-----
Merge tag 'intel-pinctrl-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/intel into devel
intel-pinctrl for v4.21-1
Switch to generic ->probe() callbacks.
Simplify getting .driver_data.
Code formatting fixes and headers clean up.
Special case is the driver for Intel Cherryview SoC, where GPIO enabling bit
was mistakenly cleared when pin gets freed. It's fixed now.
The below commit went to v4.20-rc3, that's why duplication.
- ad774315c3 MAINTAINERS: Add tree link for Intel pin control driver
The following is an automated git shortlog grouped by driver:
baytrail:
- Code formatting fixes
- simplify getting .driver_data
broxton:
- Code formatting fixes
- Get rid of unneeded ->probe() stub
cannonlake:
- Code formatting fixes
- Get rid of unneeded ->probe() stub
cedarfork:
- Replace acpi.h with mod_devicetable.h
- Get rid of unneeded ->probe() stub
cherryview:
- Stop clearing the GPIO_EN bit from chv_gpio_disable_free
- Add chv_gpio_clear_triggering() helper function
- simplify getting .driver_data
denverton:
- Replace acpi.h with mod_devicetable.h
- Get rid of unneeded ->probe() stub
geminilake:
- Code formatting fixes
icelake:
- Code formatting fixes
- Get rid of unneeded ->probe() stub
intel:
- Unexport intel_pinctrl_probe()
- simplify getting .driver_data
lewisburg:
- Replace acpi.h with mod_devicetable.h
- Get rid of unneeded ->probe() stub
MAINTAINERS:
- Add tree link for Intel pin control driver
merrifield:
- include bits.h instead of bitops.h
sunrisepoint:
- Get rid of unneeded ->probe() stub
- Two small fixes for RZ/N1.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCXApJSwAKCRCKwlD9ZEnx
cCL8APwMFxsiK5xYd4ox7v6mnTLEaSfe0qD9AHpYv27cG9B/9gEAopmBMpGLyRph
5Vk/xBiW6AUx2yKwG7qi7XBetImxRAs=
=YSf7
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v4.21-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v4.21 (take two)
- Two small fixes for RZ/N1.
checkpatch.pl suggests to use SPDX license tag. I am happy to
follow it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pin PH11 is used on various A83T board to detect a change in the OTG
port's ID pin, as in when an OTG host cable is plugged in.
The incorrect offset meant the gpiochip/irqchip was activating the wrong
pin for interrupts.
Fixes: 4730f33f0d ("pinctrl: sunxi: add allwinner A83T PIO controller support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The A64 only has one TS (transport stream) controller. The datasheet
also lists the function as TS_XXX instead of TS0_XXX.
Rename the function names now before any there are any users.
Fixes: 96851d391d ("drivers: pinctrl: add driver for Allwinner A64 SoC")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The A64 only has one CSI (camera sensor interface) controller. The
datasheet also lists the function as CSI_XXX instead of CSI0_XXX.
Rename the function names now before any there are any users.
Fixes: 96851d391d ("drivers: pinctrl: add driver for Allwinner A64 SoC")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
devm_kstrdup() may return NULL if internal allocation failed.
Thus using label, name is unsafe without checking. Therefor
in the unlikely case of allocation failure, sx150x_probe() simply
returns -ENOMEM.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: 9e80f9064e ("pinctrl: Add SX150X GPIO Extender Pinctrl Driver")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
devm_kasprintf() may return NULL on failure of internal allocation thus
the assignment to .label is not safe if not checked. On error
npcm7xx_gpio_of() returns negative values so -ENOMEM in the
(unlikely) failure case of devm_kasprintf() should be fine here.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: 3b588e43ee ("pinctrl: nuvoton: add NPCM7xx pinctrl and GPIO driver")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Clearing the GPIO_EN bit from chv_gpio_disable_free is a bad idea and
pinctrl-cherryview.c is the only Intel pinctrl driver doing something
like this.
Clearing the GPIO_EN bit means that if the pin was an output it is now
effectively floating. The datasheet is not clear what happens to pull ups /
downs in this case, but from testing it looks like these are disabled too,
also floating input pins.
One example where this is causing issues is the soc_button_array input
driver, this parses ACPI tables to create 2 platform devices for the
gpio_keys input driver. The list of GPIOs is passed through struct
gpio_keys_platform_data which uses gpio numbers rather then gpio_desc
pointers.
The buttons handled by this drivers short the pin to ground when pressed
and the volume buttons rely on the SoC's internal pull-up to pull the
pin high when the button is not pressed.
To get the gpio number, the soc_button_array code calls gpiod_get_index
followed by a desc_to_gpio call and then gpiod_put on the gpio_desc.
This last call causes chv_gpio_disable_free to clear the GPIO_EN bit.
When the gpio_keys driver then loads next it gets the gpio_desc again
causing the GPIO_EN bit to be set again and immediately reads the GPIO
value which for the volume buttons reads 0 at this time, causing a spurious
press of the volume buttons to get reported.
Putting a small delay between the gpio_desc request and the read fixes
this, I assume that this is caused by the pull-up being temporarily
disabled while the GPIO_EN bit is cleared as the powerbutton which also
has its GPIO_EN bit cleared does not have this problem.
The soc_button_array code is not the only code temporarily requesting GPIOs
the DWC3 PCI code also does this, to set the enable and reset GPIOs for the
external phy, so that the code instantiating the ULPI phy can read the
vendor and product ID registers from the phy. These GPIOs are released
after this so that the PHY driver can claim and use them when it loads.
Another example of temporary GPIO usage would be a user-space set_gpio
utility using the userspace ioctls to set a GPIO as output value 0 or 1,
having the GPIO revert to floating as soon as this utility exits would
certainly be unexpected behavior.
One argument in favor of clearing the GPIO_EN bit is if the GPIO is going
to be muxed to another function after being released, but in that case
chv_pinmux_set_mux() already clears it.
TL;DR: Clearing the GPIO_EN bit from is a bad idea, this commit therefor
removes the clearing from chv_gpio_disable_free(), replacing it with code
to clear the interrupt-trigger condition so that the GPIO stops generating
interrupts when released, as pinctrl-baytrail.c does.
Note this commit adds a !chv_pad_locked() condition to the trigger clearing
call, which the original GPIO_EN clearing code was missing.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This is a preparation patch for clearing the interrupt trigger from
chv_gpio_disable_free().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
If we assign the result of of_get_child_count() to an unsigned int,
the code will not detect any errors. Therefore assign it to an int
instead.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This fixes the check for unused mdio bus setting and the following static
checker warning:
drivers/pinctrl/pinctrl-rzn1.c:198 rzn1_pinctrl_mdio_select()
warn: always true condition '(ipctl->mdio_func[mdio] >= 0) => (0-u32max >= 0)'
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
- Fix VIN (Video IN) versioned groups on R-Car V2H, H3, and M3-W,
- Add I2C[0-3], DU1, VIN, QSPI1, and SDHI pin groups on RZ/G1C,
- Add audio, SDHI, VIN, HSCIF, and CAN(FD) support on R-Car E3,
- Add QSPI pin groups on R-Car V3M and V3H,
- Add VIN and CAN(FD) pin groups on R-Car M3-N,
- Add I2C[035] pin groups on R-Car H3 and M3-W,
- Add pinctrl and GPIO support for the new RZ/A2M (R7S9210) SoC,
- Small cleanups,
- Maintainership updates.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCW/fATQAKCRCKwlD9ZEnx
cEcRAPoCtfqfL82fb4Yj6zTrwD8dpy2TVpRYT95YRNuPegcWZwEAxpv4bUNVAMQJ
Wj6GYkhMTuGBaaUJzNGJclD7u7nJcgc=
=YGuc
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v4.21-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v4.21
- Fix VIN (Video IN) versioned groups on R-Car V2H, H3, and M3-W,
- Add I2C[0-3], DU1, VIN, QSPI1, and SDHI pin groups on RZ/G1C,
- Add audio, SDHI, VIN, HSCIF, and CAN(FD) support on R-Car E3,
- Add QSPI pin groups on R-Car V3M and V3H,
- Add VIN and CAN(FD) pin groups on R-Car M3-N,
- Add I2C[035] pin groups on R-Car H3 and M3-W,
- Add pinctrl and GPIO support for the new RZ/A2M (R7S9210) SoC,
- Small cleanups,
- Maintainership updates.
The suniv F1C100s chip (several new F-series SoCs) of Allwinner has a
pin
controller like other SoCs from Allwinner.
Add support for it.
Signed-off-by: Mesih Kilinc <mesihkilinc@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Adds support for the pin and gpio controller found in R7S9210 (RZ/A2) SoCs.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the QSPI{0|1} pins/groups/functions to the R8A77980 PFC driver.
[Sergei: ported to the upstream driver, fixed up the swapped QSPI0 SPCLK/
SSL pins, fixed up the comments, moved the QSPI pins/groups/functions to
be in the alphanumeric order, removed unneeded empty lines, renamed the
patch.]
Signed-off-by: Dmitry Shifrin <dmitry.shifrin@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
We just changed the code so we apply bias disable on the correct
register but forgot to align the register calculation. The result
is that we apply the change on the correct register, but possibly
at the incorrect offset/bit
This went undetected because offsets tends to be the same between
REG_PULL and REG_PULLEN for a given pin the EE controller. This
is not true for the AO controller.
Fixes: e39f9dd820 ("pinctrl: meson: fix pinconf bias disable")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This was missed when tiles support was added in a revison and
causes the driver to fail to load.
Fixes: 9cf0c526bc ("pinctrl: qcom: Add sdm660 pinctrl driver")
Signed-off-by: Craig Tatlor <ctatlor97@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: linux-mediatek@lists.infradead.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add PM suspend callbacks to the msm core driver that select the
sleep and default pinctrl states. Then wire those callbacks up
in the sdm845 driver, for those boards that may have GPIO hogs
that need to change state during suspend.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds MT7629 pinctrl driver based on MediaTek pinctrl-moore core.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After patch b96eea718b ("pinctrl: fsl: add scu based pinctrl support"),
NO_PAD_CTL pads map are not skipped anymore which results in
a possible memory corruption. As we actually only need to create config
maps for SCU pads and MMIO pads which are not using the default config
(a.k.a IMX_NO_PAD_CTL), so let's add a proper check before creating
the config maps. And during MMIO pads parsing, we also need update the
list_p point as SCU case to ensure the pin data next parsed is correct.
Cc: Linus Walleij <linus.walleij@linaro.org>
Fixes: b96eea718b ("pinctrl: fsl: add scu based pinctrl support")
Reported-by: Martin Kaiser <martin@kaiser.cx>
Suggested-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Martin Kaiser <martin@kaiser.cx>
Tested-by: Leonard Crestez <leonard.crestez@nxp.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pinctrl and gpio driver for Actions Semi S700 SoC. The driver
supports pinctrl, pinmux, pinconf, gpio and interrupt functionalities
through a range of registers common to both gpio driver and pinctrl driver.
Signed-off-by: Parthiban Nallathambi <pn@denx.de>
Signed-off-by: Saravanan Sekar <sravanhome@gmail.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pad control for s900 and s700 are differs in number of
pull control configuraions
s900 has 4 pull controls - high impedence, pull up, pull down, repeater
s700, s500 has 2 pull controls - pull up and pull down
so pad control configuration has to SoC specific, moved out from pinctrl
common to s900 specific.
Signed-off-by: Parthiban Nallathambi <pn@denx.de>
Signed-off-by: Saravanan Sekar <sravanhome@gmail.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move generic defines common to the Owl family out of S900 driver.
Signed-off-by: Parthiban Nallathambi <pn@denx.de>
Signed-off-by: Saravanan Sekar <sravanhome@gmail.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If a hwspinlock if defined in device tree use it to protect
configuration registers.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds CAN FD{0,1} pins, groups and functions to the R8A77990
SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
[geert: Move canfd from common to automotive]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds CAN{0,1} pins, groups and functions to the R8A77990 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds CAN FD{0,1} pins, groups and functions to the R8A77965
SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds CAN{0,1} pins, groups and functions to the R8A77965 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds I2C{0,3,5} pins, groups and functions to the R8A7796 SoC.
These pins are physically muxed with other pins. Therefore, setup of
MOD_SEL is needed for exclusive control with other pins.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds I2C{0,3,5} pins, groups and functions to
the R8A7795 ES1.x SoC.
These pins are physically muxed with other pins. Therefore, setup of
MOD_SEL is needed for exclusive control with other pins.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds I2C{0,3,5} pins, groups and functions to the R8A7795 SoC.
These pins are physically muxed with other pins. Therefore, setup of
MOD_SEL is needed for exclusive control with other pins.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Used by I2C controllers 0, 3 and 5 in R8A7795 and R8A7796 SoCs.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The PINMUX_IPSR_MSEL2() and PINMUX_IPSR_PHYS() macros are unused, and
will conflict with generic macros that are to be added.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds HSCIF{0,1,2,3,4} pins, groups and functions to
the R8A77990 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The rk3188 has pins that are not handled through the regular iomuxing
for handling either nand-flash or an emmc and are set through only one
specifal setting. So utilize the routing function to simply do that
setting depending on one of the core nand/emmc signals that are actually
regular pins handled through pinctrl.
Signed-off-by: Heiko Stuebner <heiko.stuebner@bq.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Right now we expect the pin-rounting settings to be in the same area
as the iomux setting itself. And while that seems to be true for all
newer Rockchip socs, back in the wild west days of old this wasn't true.
Nowadays pin settings in the GRF normally stay in the GRF and the same
is true for pins configured from PMU registers. But old socs like the
rk3188 really sprinkle pin settings somewhat randomly through both
for its bank0.
Therefore add the option to specify a location for the route setting,
so that we can map older socs correctly. We'll keep "same" as the
default, so that we only need to specify a location in the corner-cases
described above.
Signed-off-by: Heiko Stuebner <heiko.stuebner@bq.com>
Reviewed-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When attempting to setup up a gpio hog, device probing will repeatedly
fail with -EPROBE_DEFERED errors. It is caused by a circular dependency
between the gpio and pinctrl frameworks. If the gpio-ranges property is
present in device tree, then the gpio framework will handle the gpio pin
registration and eliminate the circular dependency.
See Christian Lamparter's commit a86caa9ba5 ("pinctrl: msm: fix
gpio-hog related boot issues") for a detailed commit message that
explains the issue in much more detail. The code comment in this commit
came from Christian's commit.
I did not test this change against any hardware supported by this
particular driver, however I was able to validate this same fix works
for pinctrl-spmi-gpio.c using a LG Nexus 5 (hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Modify GPIO direction setting in pin configuration function by using
generic GPIO functions to set the GPIO direction instead of direct
access to the GPIO direction register.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Tested-by: Kun Yi <kunyi@google.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIOX tsin_a pins wrongly uses the SDCard pinctrl bits, this
patch completely removes these pins entries until we find out what
are the correct bits and registers to be used instead.
Fixes: 5a6ae9b801 ("pinctrl: meson-gxl: add tsin_a pins")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pin, mux and functions definitions for VIN4 and VIN5 for R-Car E3.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The VIN4 and VIN5 interfaces support parallel video input.
Add pin, mux and functions definitions for VIN4 and VIN5 for R-Car M3-N.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Versioned VIN groups can appear on different sets of pins. Using the
VIN_DATA_PIN_GROUP macro now supports proper naming of said groups
through an optional 'version' argument.
Use the 'version' argument for said macro to fix naming of versioned
groups for the R-Car M3-W R8A7796 SoC.
Fixes: a5c2949ff7 ("pinctrl: sh-pfc: r8a7796: Deduplicate VIN4 pin definitions")
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Versioned VIN groups can appear on different sets of pins. Using the
VIN_DATA_PIN_GROUP macro now supports proper naming of said groups
through an optional 'version' argument.
Use the 'version' argument for said macro to fix naming of versioned
groups for the R-Car H3 R8A7795 SoC.
Fixes: 9942a5b529 ("pinctrl: sh-pfc: r8a7795: Deduplicate VIN4 pin definitions")
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
