Current DVC can be enabled only when playback,
but, this came from misunderstanding.
It is not correct.
DVC <-> DMA relationship is...
Playback: MEM -> DMAC -> SRC -> DVC -> DMACp -> SSI
Capture: SSI -> DMACp -> SRC -> DVC -> DMAC -> MEM
DVC can be used for both Playback/Capture
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current R-Car sound driver is using DMAEngine directly,
but, ASoC is requesting to use common DMA transfer method,
like snd_dmaengine_pcm_trigger() or dmaengine_pcm_ops.
It is difficult to switch at this point, since Renesas
driver is also supporting PIO transfer.
This patch uses dmaengine_prep_dma_cyclic() instead
of dmaengine_prep_slave_single().
It is used in requested method,
and is good first step to switch over.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Sound data needs to be sent to R-Car sound SSI when playback.
But, there are 2 interfaces for it.
1st is SSITDR/SSIRDR which are mapped on SSI.
2nd is SSIn_BUSIF which are mapped on SSIU.
2nd SSIn_BUSIF is used when DMA transfer,
and it is always used if sound data came from via SRC.
But, we can use it when SSI+DMA case too.
(Current driver is assuming 1st SSITDR/SSIRDR for it)
2nd SSIn_BUSIF can be used as FIFO.
This is very helpful/useful for SSI+DMA.
But DMA address / DMA ID are not same between 1st/2nd cases.
This patch care about these settings.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current FSI driver is using DMAEngine directly,
but, ASoC is requesting to use common DMA transfer method,
like snd_dmaengine_pcm_trigger() or dmaengine_pcm_ops.
It is difficult to switch at this point, since Renesas
driver is also supporting PIO transfer.
This patch uses dmaengine_prep_dma_cyclic() instead
of dmaengine_prep_slave_single().
It is used in requested method,
and is good first step to switch over.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
fsi PIO/DMA handler are using each own pointer update method,
but these can be share.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current fsi driver is using SNDRV_DMA_TYPE_CONTINUOUS
for snd_pcm_lib_preallocate_pages_for_all().
But, it came from original dma-sh7760.c,
and no longer needed.
This patch exchange its parameter, and removed
original dma mapping and un-needed
dma_sync_single_xxx() from driver.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
dmaengine_prep_slave_single() expects a enum dma_transfer_direction and not a
enum dma_data_direction. Since the integer representations of both DMA_TO_DEVICE
and DMA_MEM_TO_DEV aswell as DMA_FROM_DEVICE and DMA_DEV_TO_MEM have the same
value the code worked fine even though it was using the wrong type.
Fixes the following warning from sparse:
sound/soc/sh/rcar/core.c:227:49: warning: mixing different enum types
sound/soc/sh/rcar/core.c:227:49: int enum dma_data_direction versus
sound/soc/sh/rcar/core.c:227:49: int enum dma_transfer_direction
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current dma name search loop didn't care about SSI index
This patch fixes it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
ad32d0c7b0
(ASoC: rsnd: add rsnd_gen_dma_addr() for DMAC addr)
added rsnd_gen_dma_addr() to calculate DMA addr,
but, it is necessary only for Gen2.
This patch ignores Gen1 case.
Kernel will be panic without this patch.
Special thanks to Simon
Reported-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mark Brown <broonie@linaro.org>
Index of dma name should use -1, not +1 when capture case.
Thank you Dan.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
At this time, majority of changes come from ASoC world while we got a
few new drivers in other places for FireWire and USB. There have been
lots of ASoC core cleanups / refactoring, but very little visible to
external users.
ASoC
- Support for specifying aux CODECs in DT
- Removal of the deprecated mux and enum macros
- More moves towards full componentisation
- Removal of some unused I/O code
- Lots of cleanups, fixes and enhancements to the davinci, Freescale,
Haswell and Realtek drivers
- Several drivers exposed directly in Kconfig for use with simple-card
- GPIO descriptor support for jacks
- More updates and fixes to the Freescale SSI, Intel and rsnd drivers
- New drivers for Cirrus CS42L56, Realtek RT5639, RT5642 and RT5651 and
ST STA350, Analog Devices ADAU1361, ADAU1381, ADAU1761 and ADAU1781,
and Realtek RT5677
HD-audio:
- Clean up Dell headset quirks
- Noise fixes for Dell and Sony laptops
- Thinkpad T440 dock fix
- Realtek codec updates (ALC293,ALC233,ALC3235)
- Tegra HD-audio HDMI support
FireWire-audio:
- FireWire audio stack enhancement (AMDTP, MIDI), support for incoming
isochronous stream and duplex streams with timestamp synchronization
- BeBoB-based devices support
- Fireworks-based device support
USB-audio:
- Behringer BCD2000 USB device support
Misc:
- Clean up of a few old drivers, atmel, fm801, etc
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=nxFA
-----END PGP SIGNATURE-----
Merge tag 'sound-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound into next
Pull sound updates from Takashi Iwai:
"At this time, majority of changes come from ASoC world while we got a
few new drivers in other places for FireWire and USB. There have been
lots of ASoC core cleanups / refactoring, but very little visible to
external users.
ASoC:
- Support for specifying aux CODECs in DT
- Removal of the deprecated mux and enum macros
- More moves towards full componentisation
- Removal of some unused I/O code
- Lots of cleanups, fixes and enhancements to the davinci, Freescale,
Haswell and Realtek drivers
- Several drivers exposed directly in Kconfig for use with
simple-card
- GPIO descriptor support for jacks
- More updates and fixes to the Freescale SSI, Intel and rsnd drivers
- New drivers for Cirrus CS42L56, Realtek RT5639, RT5642 and RT5651
and ST STA350, Analog Devices ADAU1361, ADAU1381, ADAU1761 and
ADAU1781, and Realtek RT5677
HD-audio:
- Clean up Dell headset quirks
- Noise fixes for Dell and Sony laptops
- Thinkpad T440 dock fix
- Realtek codec updates (ALC293,ALC233,ALC3235)
- Tegra HD-audio HDMI support
FireWire-audio:
- FireWire audio stack enhancement (AMDTP, MIDI), support for
incoming isochronous stream and duplex streams with timestamp
synchronization
- BeBoB-based devices support
- Fireworks-based device support
USB-audio:
- Behringer BCD2000 USB device support
Misc:
- Clean up of a few old drivers, atmel, fm801, etc"
* tag 'sound-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (480 commits)
ASoC: Fix wrong argument for card remove callbacks
ASoC: free jack GPIOs before the sound card is freed
ALSA: firewire-lib: Remove a comment about restriction of asynchronous operation
ASoC: cache: Fix error code when not using ASoC level cache
ALSA: hda/realtek - Fix COEF widget NID for ALC260 replacer fixup
ALSA: hda/realtek - Correction of fixup codes for PB V7900 laptop
ALSA: firewire-lib: Use IEC 61883-6 compliant labels for Raw Audio data
ASoC: add RT5677 CODEC driver
ASoC: intel: The Baytrail/MAX98090 driver depends on I2C
ASoC: rt5640: Add the function "get_clk_info" to RL6231 shared support
ASoC: rt5640: Add the function of the PLL clock calculation to RL6231 shared support
ASoC: rt5640: Add RL6231 class device shared support for RT5640, RT5645 and RT5651
ASoC: cache: Fix possible ZERO_SIZE_PTR pointer dereferencing error.
ASoC: Add helper functions to cast from DAPM context to CODEC/platform
ALSA: bebob: sizeof() vs ARRAY_SIZE() typo
ASoC: wm9713: correct mono out PGA sources
ALSA: synth: emux: soundfont.c: Cleaning up memory leak
ASoC: fsl: Remove dependencies of boards for SND_SOC_EUKREA_TLV320
ASoC: fsl-ssi: Use regmap
ASoC: fsl-ssi: reorder and document fsl_ssi_private
...
The commit [e1d4d3c8: ASoC: free jack GPIOs before the sound card is
freed] introduced snd_soc_card remove callbacks to a few drivers, but
they are implemented with a wrong argument type. The callback should
receive snd_soc_card pointer instead of snd_soc_pcm_runtime.
Fixes: e1d4d3c854 ('ASoC: free jack GPIOs before the sound card is freed')
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is the same change as commit fb6b8e7144 "ASoC: tegra: free jack
GPIOs before the sound card is freed", but applied to all other ASoC
machine drivers where code inspection indicates the same problem exists.
That commit's description is:
==========
snd_soc_jack_add_gpios() schedules a work queue item to poll the GPIO to
generate an initial jack status report. If sound card initialization
fails, that work item needs to be cancelled, so it doesn't run after the
card has been freed. Specifically, freeing the card calls
snd_jack_dev_free() which calls snd_jack_dev_disconnect() which sets
jack->input_dev = NULL, and input_dev is used by snd_jack_report(), which
is called from the work queue item.
snd_soc_jack_free_gpios() cancels the work item. The Tegra ASoC machine
drivers do call this function in the platform driver remove() callback.
However, this happens after the sound card is freed, at least when the
card is freed due to errors late during snd_soc_instantiate_card(). This
leaves a window where the work item can execute after the card is freed.
In next-20140522, sound card initialization does fail for unrelated
reasons, and hits the problem described above.
To solve this, fix the Tegra ASoC machine drivers to clean up the Jack
GPIOs during the snd_soc_card's .remove() callback, which is executed
before the overall card object is freed. also, guard the cleanup call
based on whether we actually setup up the GPIOs in the first place.
Ideally, we'd do the cleanup in a struct snd_soc_dai_link .fini/remove
function to match where the GPIOs get set up. However, there is no such
callback.
==========
Note that I have not even compile-tested this in most cases, since most
of the drivers rely on specific mach-* support I don't have enabled, and
don't support COMPILE_TEST. Testing by the relevant board maintainers
would be useful.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
A quite large set of SoC updates this cycle. In no particular order:
- Multi-cluster power management for Samsung Exynos, adding support for
big.LITTLE CPU switching on EXYNOS5
- SMP support for Marvell Armada 375 and 38x
- SMP rework on Allwinner A31
- Xilinx Zynq support for SOC_BUS, big endian
- Marvell orion5x platform cleanup, modernizing the implementation and
moving to DT.
- _Finally_ moving Samsung Exynos over to support MULTIPLATFORM, so
that their platform can be enabled in the same kernel binary as most
of the other v7 platforms in the tree. \o/ The work isn't quite complete,
there's some driver fixes still needed, but the basics now work.
New SoC support added:
- Freescale i.MX6SX
- LSI Axxia AXM55xx SoCs
- Samsung EXYNOS 3250, 5260, 5410, 5420 and 5800
- STi STIH407
Plus a large set of various smaller updates for different platforms. I'm
probably missing some important one here.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJTjOKWAAoJEIwa5zzehBx36aEP/2vTD7x9FC59FACNHJ8iO7aw
0ebTgBBjI1Np6X18O+M7URbxV5TaBgwpUm/NDN86p03MpQ2eOXr8r47qVxe/HhZs
AdlTvzgE6QwxcVL/HeCKKUEN3BPH74+TZgFl9I5aSzNjpR39xETeK1aWP/ZiAl/q
/lGRZAQ59+c7Ung00Hg0g2YDxH9WFpK50Nj90ROnyjKSFkhIYngXYVpZB3maOypq
Pgib/U8IraKZ52oGJw3yinSoORr7FdcUdAGWGTz/lQdNL/jYDfQ6GkRW2oblWXdt
3Xvj9UW6NmkbMICucMvFuuW1nXAgutZuTp9w7mBxsiUlYepxPv/DXM6yiI1WGlEb
BeVOmOreNeN2nT6avv/uUhk3Osq63Jn9x8cz5y+7/lgWQwllh3/c+G01RotvgJEQ
vpQq5ps9fMxIAMaNP6N/YqMJI1IOrBj0iXxaZEDw3VYM/k4lSvtb3VXP9c/rqApu
U4i6hpSIGzrraU4NrjndYPndcLeNOVZbByETQKosZXuCo6G1sb7FstNSkzI9vSo8
O/pujIVUfYyBW82GzZGDw+aa7DWA29FPeUQ3p+sj5MSCg051xXT8h6QwqMo2K/zY
5ATs/qo6w7zH/Ou9rtHTRynCIb0GQJThDSlWtuXFedUF9quEltS+TDz/2o+dWtGJ
yBFGKDRuBB20D36w9xqg
=6LYI
-----END PGP SIGNATURE-----
Merge tag 'soc-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next
Pull part one of ARM SoC updates from Olof Johansson:
"A quite large set of SoC updates this cycle. In no particular order:
- Multi-cluster power management for Samsung Exynos, adding support
for big.LITTLE CPU switching on EXYNOS5
- SMP support for Marvell Armada 375 and 38x
- SMP rework on Allwinner A31
- Xilinx Zynq support for SOC_BUS, big endian
- Marvell orion5x platform cleanup, modernizing the implementation
and moving to DT.
- _Finally_ moving Samsung Exynos over to support MULTIPLATFORM, so
that their platform can be enabled in the same kernel binary as
most of the other v7 platforms in the tree. \o/
The work isn't quite complete, there's some driver fixes still
needed, but the basics now work.
New SoC support added:
- Freescale i.MX6SX
- LSI Axxia AXM55xx SoCs
- Samsung EXYNOS 3250, 5260, 5410, 5420 and 5800
- STi STIH407
plus a large set of various smaller updates for different platforms.
I'm probably missing some important one here"
* tag 'soc-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (281 commits)
ARM: exynos: don't run exynos4 l2x0 setup on other platforms
ARM: exynos: Fix "allmodconfig" build errors in mcpm and hotplug
ARM: EXYNOS: mcpm rename the power_down_finish
ARM: EXYNOS: Enable mcpm for dual-cluster exynos5800 SoC
ARM: EXYNOS: Enable multi-platform build support
ARM: EXYNOS: Consolidate Kconfig entries
ARM: EXYNOS: Add support for EXYNOS5410 SoC
ARM: EXYNOS: Support secondary CPU boot of Exynos3250
ARM: EXYNOS: Add Exynos3250 SoC ID
ARM: EXYNOS: Add 5800 SoC support
ARM: EXYNOS: initial board support for exynos5260 SoC
clk: exynos5410: register clocks using common clock framework
ARM: debug: qcom: add UART addresses to Kconfig help for APQ8084
ARM: sunxi: allow building without reset controller
Documentation: devicetree: arm: sort enable-method entries
ARM: rockchip: convert smp bringup to CPU_METHOD_OF_DECLARE
clk: exynos5250: Add missing sysmmu clocks for DISP and ISP blocks
ARM: dts: axxia: Add reset controller
power: reset: Add Axxia system reset driver
ARM: axxia: Adding defconfig for AXM55xx
...
It is not an error to have no cache so we shouldn't return an error code
and cause our callers to fail, just silently do nothing instead. Thanks
to Jarkko for identify the problematic commit.
Reported-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reported-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The patch adds the function "get_clk_info" to RL6231 shared support.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The patch adds the function of the PLL clock calculation to RL6231 shared
support.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The patch adds the RL6231 class device shared support for RT5640, RT5645 and
RT5651. The function of the DMIC clock calculation can be shared by RL6231
shared support.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since we cannot make sure the 'reg_size' will always be none zero here,
and then if 'reg_size' equals to zero, the kzalloc() will return ZERO_SIZE_PTR,
which equals to ((void *)16).
So this patch fix this with just doing the 'reg_size' zero check before calling
kzalloc().
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The mono output PGA input only has four possible sources, so
omit the rest.
Signed-off-by: Matt Reimer <mreimer@sdgsystems.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Eukrea-i.MX51 board was converted to use DT, ie we no longer have a
MACH_EUKREA_MBIMXSD51_BASEBOARD symbol.
Transformation of other boards planned for the near future, so this
patch removes all these dependencies and restricts build of this
driver to ARCH_MXC.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch replaces the ssi specific functions write_ssi, read_ssi and
write_ssi_mask by standard regmap function calls.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Reorder all variables in struct fsl_ssi_private to have groups that make
sense together. The patch also updates the struct documentation.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The baudclock may be used and set by different streams.
Allow only the first stream to set the bitclock rate. Other streams have
to try to get to the correct rate without modifying the bitclock rate
using the SSI internal clock modifiers.
The variable baudclk_streams is introduced to keep track of the active
streams that are using the baudclock. This way we know if the baudclock
may be set and whether we may enable/disable the clock.
baudclock enable/disable is moved to hw_params()/hw_free(). This way we can
keep track of the baudclock in those two functions and avoid a running
clock while it is not used. As hw_params()/hw_free() may be called
multiple times for the same stream, we have to use baudclk_streams
variable to know whether we may enable/disable the clock.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
In i2s master mode the fsl_ssi driver depends on someone calling
.set_tdm_slot correctly. In this mode though only a DC value of
2 is allowed, so set it in this case and no longer depend on
.set_tdm_slot.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The baudclock_locked variable is only used in functions which
are serialized anyway from the core. No need to have a lock
around the variable, so remove it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The fsl_ssi driver uses the .set_sysclk callback to configure the
bitclock for master mode. This is unnecessary since the bitclock
is known in hw_params. This patch configures the bitclock from .hw_params.
.set_dai_sysclk now sets a bitclock frequency which is preferred over
the default calculated bitclock frequency.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The simple soundcard binding has its own way for specifying the dai
format. To be able to use this binding we have to make the fsl,mode
property optional. As the property is used in existing devicetrees
keep the option around for compatibility reasons.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Introduce a SoC data struct which contains the differences between
the different SoCs this driver supports. This makes it easy to support
more differences without having to introduce a new switch/case each
time.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use card PM ops from ASoC core instead of defining custom PM ops here since
we are calling anyway common suspend/resume callbacks.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Simplify byt-rt5640.c and haswell.c machine drivers by using
devm_snd_soc_register_card(). Remove also needless dev_set_drvdata()
from byt_rt5640_probe() since snd_soc_register_card() does it too.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
