All of the switches in N2_count_control in the counter configuration are
required to make the branch if not equal and increment command work.
Set them when using bneq+.
A side effect of this mode requires a dummy write to TDR when both
transmitting and receiving otherwise the controller won't start shifting
receive data.
It is likely not possible to avoid TDR underrun errors in this mode and
they are harmless, so do not check for them.
Fixes: bbb6b2f986 ("spi: Add FSI-attached SPI controller driver")
Signed-off-by: Brad Bishop <bradleyb@fuzziesquirrel.com>
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20200909222857.28653-4-eajames@linux.ibm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use a clock divider tuned to a 200MHz FSI bus frequency (the maximum). Use
of the previous divider at 200MHz results in corrupt data from endpoint
devices. Ideally the clock divider would be calculated from the FSI clock,
but that would require some significant work on the FSI driver. With FSI
frequencies slower than 200MHz, the SPI clock will simply run slower, but
safely.
Signed-off-by: Brad Bishop <bradleyb@fuzziesquirrel.com>
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20200909222857.28653-3-eajames@linux.ibm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The trailing <len> - 8 bytes of transfer data in this size range is no
longer ignored.
Fixes: bbb6b2f986 ("spi: Add FSI-attached SPI controller driver")
Signed-off-by: Brad Bishop <bradleyb@fuzziesquirrel.com>
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20200909222857.28653-2-eajames@linux.ibm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This eliminates the following sparse warning:
drivers/spi/spi-bcm2835.c:78:14: warning: symbol 'polling_limit_us' was
not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Link: https://lore.kernel.org/r/20200912072211.602735-1-yanaijie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chunyan Zhang <zhang.lyra@gmail.com>
Link: https://lore.kernel.org/r/20200910160706.5883-1-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
If we're sending bytes over SPI, we know the FIFO is empty at the
start of the transfer. There's no reason to wait for the interrupt
telling us to start--we can just start right away. Then if we
transmit everything in one swell foop we don't even need to bother
listening for TX interrupts.
In a test of "flashrom -p ec -r /tmp/foo.bin" interrupts were reduced
from ~30560 to ~29730, about a 3% savings.
This patch looks bigger than it is because I moved a few functions
rather than adding a forward declaration. The only actual change to
geni_spi_handle_tx() was to make it return a bool indicating if there
is more to tx.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200912111716.1.Ied5e843fad0d6b733a1fb8bcfb364dd2fa889eb3@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
This eliminates the following sparse warning:
drivers/spi/spi-bcm2835.c:78:14: warning: symbol 'polling_limit_us' was
not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Link: https://lore.kernel.org/r/20200912072211.602735-1-yanaijie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi device tree lacks DMA
channels for DSPI, so naturally, the driver fails to probe:
[ 2.945302] fsl-dspi 2100000.spi: rx dma channel not available
[ 2.951134] fsl-dspi 2100000.spi: can't get dma channels
In retrospect, this should have been obvious, because LS2080A, LS2085A
LS2088A and LX2160A don't appear to have an eDMA module at all. Looking
again at their datasheets, the CTARE register (which is specific to XSPI
functionality) seems to be documented, so switch them to XSPI mode
instead.
Fixes: 0feaf8f5af ("spi: spi-fsl-dspi: Convert the instantiations that support it to DMA")
Reported-by: Qiang Zhao <qiang.zhao@nxp.com>
Tested-by: Qiang Zhao <qiang.zhao@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20200910121532.1138596-1-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We always toggle the chip select manually in spi-geni-qcom so that we
can properly implement the Linux API. There's no reason to program
this to the hardware on every transfer. Program it once at init and
be done with it.
This saves some part of a microsecond of overhead on each transfer.
While not really noticeable on any real world benchmarks, we might as
well save the time.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200912140730.2.I33e571179986850b4ec17042e813d0b08fb1b9c1@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
In commit 902481a78e ("spi: spi-geni-qcom: Actually use our FIFO") I
explained that the maximum size we could program the FIFO was
"mas->tx_fifo_depth - 3" but that I chose "mas->tx_fifo_depth()"
because I was worried about decreased bandwidth.
Since that time:
* All the interconnect patches have landed, making things run at the
proper speed.
* I've done more measurements.
This lets me confirm that there's really no downside of using the FIFO
more. Specifically I did "flashrom -p ec -r /tmp/foo.bin" on a
Chromebook and averaged over several runs.
Before: It took 6.66 seconds and 59669 interrupts fired.
After: It took 6.66 seconds and 47992 interrupts fired.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200912140730.1.Ie67fa32009b94702d56232c064f1d89065ee8836@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
It is redundant to do irqsave and irqrestore in hardIRQ context.
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
Link: https://lore.kernel.org/r/20200910100246.32696-1-song.bao.hua@hisilicon.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Broadcom QSPI driver now falls back to no MSPI_DEV support as the
default setting in the generic compatible string, explicit settings for
STB chips 7425, 7429, and 7435 can be removed.
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20200910152539.45584-4-ray.jui@broadcom.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add compatible string for BRCMSTB 7445 SoCs and indicate it has MSPI rev
support.
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20200910152539.45584-2-ray.jui@broadcom.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The variable ret is being initialized with a value that is
never read and it is being updated later with a new value. The
initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200910150410.750959-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Big cleanup for the Samsung S3C24xx and S3C64xx platforms, although it
also touches files shared with S5Pv210 and Exynos. This is mostly Arnd
Bergmann work which Krzysztof Kozlowski took over, rebased and polished.
The goal is to cleanup, merge and finally make the Samsung S3C24xx and
S3C64xx architectures multiplatform. The multiplatform did not happen
yet here - just cleaning up and merging into one arch/arm/mach-s3c
directory. However this is step forward for multiplatform or at least
to keep this code still maintainable.
This pulls also branch with changes for Samsung SoC sound drivers from
broonie/sound because the cleanups there were part of this series and
all further patches depend on them.
-----BEGIN PGP SIGNATURE-----
iQJEBAABCgAuFiEE3dJiKD0RGyM7briowTdm5oaLg9cFAl9NGucQHGtyemtAa2Vy
bmVsLm9yZwAKCRDBN2bmhouD1zzWD/0T5JdPls++8JUK04hxkunMJO3Ye2ir/a2C
YAI2M6fbOludcPeGCRnPBZ3uTbeSOXFrV6UuSVi8EVKoAb0EV3G50XGQecmy/TVx
nq/c90gtnsODL0Kxjm0767WZl9clKaIE3+VNSyQXAhqJqXK8A1L8ovsUpQEj6fr4
vaNQi6lW7o0r98OEB14M0z59lSWjanUZ33/R22L3AsRihlJTH0Sye2+zVG85LfMD
5okekSHndt2/NCUxgLTZIkp/cD/pzmhMRZTl1zWvZPPFsbzpuB9wZt46b7vkEzuN
NgPElEB9AJgyh/28D064lER6TFhz3TcATZjmEIXX+3tYIaoA2lj60QiSejM2FyBk
U5a0DYAyzwNs4R1GSQxrKnQS1AXQ+yoDniPcyNaSmuZbxaodAs9Hjxg9KfJ2bfs5
DFfSUJhf1Uam8UYolMbXqSkhd2KQjXpkF0eLK7sGk3wanO+YEqVs777fHpwIPLmd
767PD0YN+EfDUwmXAJ5Jgv2kvOJIGul7BTgpWtbRHEaDvLHRQl5OhjsWsj9kWCFX
fx0Jz1sAUqi+gNq3XUFM88/VPEkTgejmVRULnBxqVsar5b/0BeRJEgA6Ljycv0Jv
2ux5zdMuX/+Xc4zdaJOWaL8NqRuT8nSynKXbWHTzJk4cF3p12/g3q3LOHBBLcLL6
AzTEA6iZ0w==
=bjMI
-----END PGP SIGNATURE-----
Merge tag 'samsung-soc-s3c-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/soc
Samsung S3C24xx and S3C64xx machine code cleanup for v5.10
Big cleanup for the Samsung S3C24xx and S3C64xx platforms, although it
also touches files shared with S5Pv210 and Exynos. This is mostly Arnd
Bergmann work which Krzysztof Kozlowski took over, rebased and polished.
The goal is to cleanup, merge and finally make the Samsung S3C24xx and
S3C64xx architectures multiplatform. The multiplatform did not happen
yet here - just cleaning up and merging into one arch/arm/mach-s3c
directory. However this is step forward for multiplatform or at least
to keep this code still maintainable.
This pulls also branch with changes for Samsung SoC sound drivers from
broonie/sound because the cleanups there were part of this series and
all further patches depend on them.
* tag 'samsung-soc-s3c-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (62 commits)
ARM: s3c: Avoid naming clash of S3C24xx and S3C64xx timer setup
ARM: s3c: Cleanup from old plat-samsung include
ARM: s3c: make headers local if possible
ARM: s3c: move into a common directory
ARM: s3c24xx: stop including mach/hardware.h from mach/io.h
cpufreq: s3c24xx: move low-level clk reg access into platform code
cpufreq: s3c2412: use global s3c2412_cpufreq_setrefresh
ARM: s3c: remove cpufreq header dependencies
cpufreq: s3c24xx: split out registers
fbdev: s3c2410fb: remove mach header dependency
ARM: s3c24xx: bast: avoid irq_desc array usage
ARM: s3c24xx: spi: avoid hardcoding fiq number in driver
ARM: s3c24xx: include mach/irqs.h where needed
ARM: s3c24xx: move s3cmci pinctrl handling into board files
ARM: s3c24xx: move iis pinctrl config into boards
ARM: s3c24xx: move spi fiq handler into platform
ARM: s3c: adc: move header to linux/soc/samsung
ARM: s3c24xx: move irqchip driver back into platform
ARM: s3c24xx: move regs-spi.h into spi driver
ARM: s3c64xx: remove mach/hardware.h
...
Link: https://lore.kernel.org/r/20200831154751.7551-1-krzk@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
There's some driver specific fixes here plus one core fix for memory
leaks that could be triggered by a potential race condition when
cleaning up after we have split transfers to fit into what the
controller can support.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl9bavQTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0JuiCACAZcBZFb6hshADoyt9YCCjQrD1+khD
AzkSuDOE6UP3SGOEBx/29QL1kE7j0V9ARC0XLVZutzZhUXbIvJ1ulgUqGgeQSnLz
ZvO/rIJiC+lsKIZQANgOBjOzWhfRzYXPOwfQwtsta5NfrP5ZafKJ5iG2C0xjnETr
Arybcx8D/EDZWKQ9PntM246J/jlmK+dsnK6wouqHlP2ulo3O4UQUxN0D5SjUC0RW
3xMH165RvIqwu0L5iCUWmzQhPuxuhk2QWpt48k3dPghmNx9XNGJuHDRI0THRxIp/
2mNRXiK0qKma4AwWO7+JJshyeXufR07HNMYfkL/d159K6QOsu1Uaq4z4
=d1ma
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v5.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"There's some driver specific fixes here plus one core fix for memory
leaks that could be triggered by a potential race condition when
cleaning up after we have split transfers to fit into what the
controller can support"
* tag 'spi-fix-v5.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: stm32: fix pm_runtime_get_sync() error checking
spi: Fix memory leak on splited transfers
spi: spi-cadence-quadspi: Fix mapping of buffers for DMA reads
spi: stm32: Rate-limit the 'Communication suspended' message
spi: spi-loopback-test: Fix out-of-bounds read
spi: spi-cadence-quadspi: Populate get_name() interface
MAINTAINERS: add myself as maintainer for spi-fsl-dspi driver
The arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi device tree lacks DMA
channels for DSPI, so naturally, the driver fails to probe:
[ 2.945302] fsl-dspi 2100000.spi: rx dma channel not available
[ 2.951134] fsl-dspi 2100000.spi: can't get dma channels
In retrospect, this should have been obvious, because LS2080A, LS2085A
LS2088A and LX2160A don't appear to have an eDMA module at all. Looking
again at their datasheets, the CTARE register (which is specific to XSPI
functionality) seems to be documented, so switch them to XSPI mode
instead.
Fixes: 0feaf8f5af ("spi: spi-fsl-dspi: Convert the instantiations that support it to DMA")
Reported-by: Qiang Zhao <qiang.zhao@nxp.com>
Tested-by: Qiang Zhao <qiang.zhao@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20200910121532.1138596-1-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Hello,
This cleans up some of the user code around calls to
dev_pm_opp_of_remove_table().
All the patches can be picked by respective maintainers directly except
for the last patch, which needs the previous two to get merged first.
These are based for 5.9-rc1.
Rajendra, Since most of these changes are related to qcom stuff, it
would be great if you can give them a try. I wasn't able to test them
due to lack of hardware.
Ulf, I had to revise the sdhci patch, sorry about that. Please pick this
one.
Diff between V1 and V2 is mentioned in each of the patches separately.
Viresh Kumar (8):
cpufreq: imx6q: Unconditionally call dev_pm_opp_of_remove_table()
drm/lima: Unconditionally call dev_pm_opp_of_remove_table()
drm/msm: Unconditionally call dev_pm_opp_of_remove_table()
mmc: sdhci-msm: Unconditionally call dev_pm_opp_of_remove_table()
spi: spi-geni-qcom: Unconditionally call dev_pm_opp_of_remove_table()
spi: spi-qcom-qspi: Unconditionally call dev_pm_opp_of_remove_table()
tty: serial: qcom_geni_serial: Unconditionally call
dev_pm_opp_of_remove_table()
qcom-geni-se: remove has_opp_table
drivers/cpufreq/imx6q-cpufreq.c | 10 ++--------
drivers/gpu/drm/lima/lima_devfreq.c | 6 +-----
drivers/gpu/drm/lima/lima_devfreq.h | 1 -
drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c | 14 +++++---------
drivers/gpu/drm/msm/disp/dpu1/dpu_kms.h | 1 -
drivers/gpu/drm/msm/dsi/dsi_host.c | 8 ++------
drivers/mmc/host/sdhci-msm.c | 14 +++++---------
drivers/spi/spi-geni-qcom.c | 13 +++++--------
drivers/spi/spi-qcom-qspi.c | 15 ++++++---------
drivers/tty/serial/qcom_geni_serial.c | 13 +++++--------
include/linux/qcom-geni-se.h | 2 --
11 files changed, 31 insertions(+), 66 deletions(-)
base-commit: f4d51dffc6
--
2.25.0.rc1.19.g042ed3e048af
In spidev_read() and spidev_write(), the variable status is being
initialized with a value that is never read and it is being updated
later with a new value. The initialization is redundant and can be
removed.
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/1599631704-53232-1-git-send-email-f.fangjian@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dev_pm_opp_of_remove_table() doesn't report any errors when it fails to
find the OPP table with error -ENODEV (i.e. OPP table not present for
the device). And we can call dev_pm_opp_of_remove_table()
unconditionally here.
While at it, create a new label and put clkname on errors.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/b77aa0bbe82a580508e321a34da488b4b27966d0.1598594714.git.viresh.kumar@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
dev_pm_opp_of_remove_table() doesn't report any errors when it fails to
find the OPP table with error -ENODEV (i.e. OPP table not present for
the device). And we can call dev_pm_opp_of_remove_table()
unconditionally here.
While at it, create a new label and put clkname on errors.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/ea0864d41277e61fa31d304fbd4cf9af6b314269.1598594714.git.viresh.kumar@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The pm_runtime_get_sync() can return either 0 or 1 on success but this
code treats 1 as a failure.
Fixes: db96bf976a ("spi: stm32: fixes suspend/resume management")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Alain Volmat <alain.volmat@st.com>
Link: https://lore.kernel.org/r/20200909094304.GA420136@mwanda
Signed-off-by: Mark Brown <broonie@kernel.org>
In the prepare_message callback the bus driver has the
opportunity to split a transfer into smaller chunks.
spi_map_msg is done after prepare_message.
Function spi_res_release releases the splited transfers
in the message. Therefore spi_res_release should be called
after spi_map_msg.
The previous try at this was commit c9ba7a16d0
which released the splited transfers after
spi_finalize_current_message had been called.
This introduced a race since the message struct could be
out of scope because the spi_sync call got completed.
Fixes this leak on spi bus driver spi-bcm2835.c when transfer
size is greater than 65532:
Kmemleak:
sg_alloc_table+0x28/0xc8
spi_map_buf+0xa4/0x300
__spi_pump_messages+0x370/0x748
__spi_sync+0x1d4/0x270
spi_sync+0x34/0x58
spi_test_execute_msg+0x60/0x340 [spi_loopback_test]
spi_test_run_iter+0x548/0x578 [spi_loopback_test]
spi_test_run_test+0x94/0x140 [spi_loopback_test]
spi_test_run_tests+0x150/0x180 [spi_loopback_test]
spi_loopback_test_probe+0x50/0xd0 [spi_loopback_test]
spi_drv_probe+0x84/0xe0
Signed-off-by: Gustav Wiklander <gustavwi@axis.com>
Link: https://lore.kernel.org/r/20200908151129.15915-1-gustav.wiklander@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The series add support for the Sparx5 SoC SPI controller in the
spi-dw-mmio.c spi driver.
v5 changes:
- rx-sample-delay-ns documentation changes from Rob Herring:
- Drop superfluous type $ref
- Add default value = 0
v4 changes:
- Changed snps,rx-sample-delay-ns to snps,rx-sample-delay-ns
suggested by Rob Herring (rockchip also has this property).
- Added support for controller-level rx-sample-delay-ns value as
well as per SPI slave value (rockchip has controller-level property).
- Dropped internal mux in favor of suggested spi-mux to
control bus inteface selection.
v3 changes:
- Added mux support for controlling SPI bus interface. This is new mux
driver, bindings and added to sparx5 base DT.
- Removed "microchip,spi-interface2" property in favour of
"mux-controls" property in SPI controller (sparx5 only).
- Changed dw_spi_sparx5_set_cs() to use the mux control instead of
directly acessing "mux" register. Associated code/defines moved to mux
driver.
- Changed dw_spi_sparx5_set_cs() to match other similar functions in
signature and avoid explicit CS toggling.
- Spun off duplicated NAND device DT chunks into separate DT file.
v2 changes:
- Moved all RX sample delay into spi-dw-core.c, using
the "snps,rx-sample-delay-ns" device property.
- Integrated Sparx5 support directly in spi-dw-mmio.c
- Changed SPI2 configuration to per-slave "microchip,spi-interface2"
property.
- Added bindings to existing snps,dw-apb-ssi.yaml file
- Dropped patches for polled mode and SPI memory operations.
Lars Povlsen (6):
spi: dw: Add support for RX sample delay register
spi: dw: Add Microchip Sparx5 support
arm64: dts: sparx5: Add SPI controller and associated mmio-mux
dt-bindings: snps,dw-apb-ssi: Add sparx5 support, plus
rx-sample-delay-ns property
arm64: dts: sparx5: Add spi-nor support
arm64: dts: sparx5: Add spi-nand devices
.../bindings/spi/snps,dw-apb-ssi.yaml | 21 ++++++
arch/arm64/boot/dts/microchip/sparx5.dtsi | 47 ++++++++++++-
.../arm64/boot/dts/microchip/sparx5_nand.dtsi | 31 ++++++++
.../boot/dts/microchip/sparx5_pcb125.dts | 30 ++++++++
.../boot/dts/microchip/sparx5_pcb134.dts | 1 +
.../dts/microchip/sparx5_pcb134_board.dtsi | 16 +++++
.../boot/dts/microchip/sparx5_pcb135.dts | 1 +
.../dts/microchip/sparx5_pcb135_board.dtsi | 16 +++++
drivers/spi/spi-dw-core.c | 26 +++++++
drivers/spi/spi-dw-mmio.c | 70 ++++++++++++++++++-
drivers/spi/spi-dw.h | 3 +
11 files changed, 260 insertions(+), 2 deletions(-)
create mode 100644 arch/arm64/boot/dts/microchip/sparx5_nand.dtsi
--
2.27.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Use default supports_op() to support spi-[rt]x-bus-width properties.
And check dummy op's byte length instead of its bus width for output.
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Link: https://lore.kernel.org/r/20200826091852.519138-1-ikjn@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200901152713.18629-11-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200901152713.18629-10-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200901152713.18629-9-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200901152713.18629-8-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200901152713.18629-7-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200901152713.18629-6-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200901152713.18629-5-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20200901152713.18629-4-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200901152713.18629-3-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
If dma_request_chan() for TX channel fails with EPROBE_DEFER, the RX
channel would not be released and on next re-probe it would be requested
second time.
Fixes: 386119bc7b ("spi: sprd: spi: sprd: Add DMA mode support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chunyan Zhang <zhang.lyra@gmail.com>
Link: https://lore.kernel.org/r/20200901152713.18629-1-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds SPI support for the Sparx5 SoC, which is using the MMIO
Designware SPI controller.
The Sparx5 differs from the Ocelot version in these areas:
* The CS override is controlled by a new set of registers for
this purpose.
* The Sparx5 SPI controller has the RX sample delay register, and it
must be configured for the (SPI NAND) device on SPI2.
* The Sparx5 SPI controller has 2 different SPI bus interfaces on the
same controller (don't ask...). The "spi-mux" driver should be used
in conjunction with the SPI driver to select the appropriate bus.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Link: https://lore.kernel.org/r/20200824203010.2033-3-lars.povlsen@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This add support for the RX_SAMPLE_DLY register. If enabled in the
Designware IP, it allows tuning of the rx data signal by means of an
internal rx sample fifo.
The register is controlled by the rx-sample-delay-ns DT property,
which is defined per SPI slave as well on controller level.
The controller level rx-sample-delay-ns will apply to all slaves
without the property explicitly defined.
The register is located at offset 0xf0, and if the option is not
enabled in the IP, changing the register will have no effect. The
register will only be written if any slave defines a nonzero value
(after scaling by the clock period).
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Link: https://lore.kernel.org/r/20200824203010.2033-2-lars.povlsen@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Buffers need to mapped to DMA channel's device pointer instead of SPI
controller's device pointer as its system DMA that actually does data
transfer.
Data inconsistencies have been reported when reading from flash
without this fix.
Fixes: ffa639e069 ("mtd: spi-nor: cadence-quadspi: Add DMA support for direct mode reads")
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Link: https://lore.kernel.org/r/20200831130720.4524-1-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There seems no reason to restrict testing to ARM, so remove this
constraint to improve test coverage.
Build-tested with allyesconfig on x86.
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Link: https://lore.kernel.org/r/20200904163709.110975-1-alex.dewar90@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The 'spi_stm32 44004000.spi: Communication suspended' message means that
when using PIO, the kernel did not read the FIFO fast enough and so the
SPI controller paused the transfer. Currently, this is printed on every
single such event, so if the kernel is busy and the controller is pausing
the transfers often, the kernel will be all the more busy scrolling this
message into the log buffer every few milliseconds. That is not helpful.
Instead, rate-limit the message and print it every once in a while. It is
not possible to use the default dev_warn_ratelimited(), because that is
still too verbose, as it prints 10 lines (DEFAULT_RATELIMIT_BURST) every
5 seconds (DEFAULT_RATELIMIT_INTERVAL). The policy here is to print 1 line
every 50 seconds (DEFAULT_RATELIMIT_INTERVAL * 10), because 1 line is more
than enough and the cycles saved on printing are better left to the CPU to
handle the SPI. However, dev_warn_once() is also not useful, as the user
should be aware that this condition is possibly recurring or ongoing. Thus
the custom rate-limit policy.
Finally, turn the message from dev_warn() to dev_dbg(), since the system
does not suffer any sort of malfunction if this message appears, it is
just slowing down. This further reduces the printing into the log buffer
and frees the CPU to do useful work.
Fixes: dcbe0d84df ("spi: add driver for STM32 SPI controller")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Amelie Delaunay <amelie.delaunay@st.com>
Cc: Antonio Borneo <borneo.antonio@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20200905151913.117775-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The "tx/rx-transfer - crossing PAGE_SIZE" test always fails when
len=131071 and rx_offset >= 5:
spi-loopback-test spi0.0: Running test tx/rx-transfer - crossing PAGE_SIZE
...
with iteration values: len = 131071, tx_off = 0, rx_off = 3
with iteration values: len = 131071, tx_off = 0, rx_off = 4
with iteration values: len = 131071, tx_off = 0, rx_off = 5
loopback strangeness - rx changed outside of allowed range at: ...a4321000
spi_msg@ffffffd5a4157690
frame_length: 131071
actual_length: 131071
spi_transfer@ffffffd5a41576f8
len: 131071
tx_buf: ffffffd5a4340ffc
Note that rx_offset > 3 can only occur if the SPI controller driver sets
->dma_alignment to a higher value than 4, so most SPI controller drivers
are not affect.
The allocated Rx buffer is of size SPI_TEST_MAX_SIZE_PLUS, which is 132
KiB (assuming 4 KiB pages). This test uses an initial offset into the
rx_buf of PAGE_SIZE - 4, and a len of 131071, so the range expected to
be written in this transfer ends at (4096 - 4) + 5 + 131071 == 132 KiB,
which is also the end of the allocated buffer. But the code which
verifies the content of the buffer reads a byte beyond the allocated
buffer and spuriously fails because this out-of-bounds read doesn't
return the expected value.
Fix this by using ITERATE_LEN instead of ITERATE_MAX_LEN to avoid
testing sizes which cause out-of-bounds reads.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20200902132341.7079-1-vincent.whitchurch@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The register offset is already included in the device name so even prior
%p values being hashed printing the base was redundant. Remove the %p
from the dev_info() output.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20200825050856.29616-1-chris.packham@alliedtelesis.co.nz
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Implement get_name() interface of spi_controller_mem_ops so as to avoid
changing of mtd->name due to driver being moved over to spi-mem
framework from SPI NOR. This avoids breaking of MTD cmdline args being
passed by bootloaders which maybe using old driver name.
Fixes: 31fb632b5d ("spi: Move cadence-quadspi driver to drivers/spi/")
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200825172506.14375-1-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
After the only user of the limited EOQ mode has now been converted to
DMA as of commit b09058bbf5 ("spi: spi-fsl-dspi: set ColdFire to DMA
mode"), we can finally delete this code.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20200823212657.2400075-1-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Hi Mark,
This patch series contains several improvements for the Renesas SPI/QSPI
driver related to bit rate configuration.
Changes compared to v1
(https://lore.kernel.org/r/20200608095940.30516-1-geert+renesas@glider.be):
- Drop accepted patch.
This has been tested on RSK+RZA1 (RSPI) and R-Car M2-W/Koelsch (QSPI),
using a scope and logic analyzer, except for the by-one divider on QSPI.
This has not been tested on legacy SuperH, due to lack of hardware.
Thanks for your comments!
Geert Uytterhoeven (7):
spi: rspi: Remove useless .set_config_register() check
spi: rspi: Clean up Bit Rate Division Setting handling
spi: rspi: Increase bit rate accuracy on RZ/A
spi: rspi: Increase bit rate range for RSPI on SH
spi: rspi: Increase bit rate range for QSPI
spi: rspi: Fill in spi_transfer.effective_speed_hz
spi: rspi: Fill in controller speed limits
drivers/spi/spi-rspi.c | 81 +++++++++++++++++++++++++++---------------
1 file changed, 52 insertions(+), 29 deletions(-)
--
2.17.1
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
There is no point in printing a plain "probed" message on successful probe.
Just remove it and make the kernel log a bit less noisy.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20200819123330.22880-1-festevam@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fill in the controller speed limits, so the SPI core can use them for
validating SPI transfers, and adjusting them where needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200819125904.20938-8-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Fill in the effective bit rate used for transfers, so the SPI core can
calculate instead of estimate delays.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200819125904.20938-7-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Increase bit rate range for QSPI by extending the range of supported
dividers:
1. QSPI supports a divider of 1, by setting SPBR to zero, increasing
the upper limit from 48.75 to 97.5 MHz on R-Car Gen2,
2. Make use of the Bit Rate Frequency Division Setting field in
Command Registers, to decrease the lower limit from 191 to 24 kbps
on R-Car Gen2.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200819125904.20938-6-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Increase bit rate range for RSPI on legacy SH by making use of the Bit
Rate Frequency Division Setting field in Command Registers, just like is
already done on RZ/A. This decreases the lower limit by a factor of 8.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200819125904.20938-5-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
rspi_rz_set_config_register() favors high values of "brdv" over high
values of "spbr". As "brdv" is not a plain divider, but controls a
power-of-two divider, this may cause the selection of non-optimal
divider values. E.g. on RSK+RZA1, when 3.8 MHz is requested, the actual
configured bit rate is 2.08 MHz (spbr = 1, brdv = 3), while 3.7 MHz
would be possible (spbr = 8, brdv = 0).
Fix this by only resorting to higher "brdv" values when really needed.
This makes the driver always pick optimal divider values on RZ/A.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200819125904.20938-4-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a macro for configuring the Bit Rate Division Setting field in
Command Registers, instead of open-coding the same operation using a
hardcoded shift.
Rename "div" to "brdv", as it is not a plain divider value, but controls
a power-of-two divider.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200819125904.20938-3-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Not implementing spi_ops.set_config_register() is a driver bug that
would prevent the driver from working at all.
Hence remove the run-time check.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200819125904.20938-2-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
The IRQ_EINT0 constant is a platform detail that is
defined in mach/irqs.h and not visible to drivers once
that header is made private.
Since the same calculation already happens in s3c24xx_set_fiq,
just return the value from there.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20200806182059.2431-31-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The fiq handler needs access to some register definitions that
should not be used directly by device drivers.
Since this is closely related to the irqchip driver anyway,
move it into the same place.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[krzk: Add a header guard in include/linux/spi/s3c24xx-fiq.h, fix
SPDX comment style, update maintainer's entry]
Co-developed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200806182059.2431-23-krzk%40kernel.org
Acked-by: Mark Brown <broonie@kernel.org>
The file is mostly specific to the driver, the few bits that
are actually used by the platform code get moved to mach/map.h
instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20200806182059.2431-20-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The plat-samsung directory and mach-s5pv210 can be build
completely independently, so split the two Kconfig symbols
CONFIG_PLAT_SAMSUNG and CONFIG_ARCH_S5PV210.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20200806182059.2431-18-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
There are cases that DMA is not used and the driver gracefully
falls back to PIO mode.
Do not treat it like an error message and move it to debug level instead.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20200818223519.8737-1-festevam@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A bunch of fixes that came in for SPI during the merge window, a bunch
from ST and others for their controller, one from Lukas for a race
between device addition and controller unregistration and one from fix
from Geert for the DT bindings which unbreaks validation.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl88HlMTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0LSaB/9aKqZmi7DUz1mguWny26NdYwBfYjW/
tZzpK/wfdwOoaxnxlSpZjA1tTOgjIFKQK1mN3adkKyqh1KByokSMHN0jp9nTM/BM
VyYid0jv0mnoANXCUWueQMcGxE990cRGbrJoywEY47VdGBSxGUdOiv/NukgZv8wa
z0ijmA7phTe1cCavp5rzB/fdNbOj4STg0ErgArVrafXV1E/fHvnjjTtPf2RtXWTU
LuUBw51Uo1wBZch9gDcvqiBhyfuXxk7ik+U0e0nRVeRTTw0F/ZpVqpob95mHyWm+
YuDjn/SRyZRpIdr9uxwpSEUxNB6sowAs5MJOcxesjSHJBIU77WAwX7bA
=BjOG
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A bunch of fixes that came in for SPI during the merge window.
Some from ST and others for their controller, one from Lukas for a
race between device addition and controller unregistration and one
from fix from Geert for the DT bindings which unbreaks validation"
* tag 'spi-fix-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
dt-bindings: lpspi: Add missing boolean type for fsl,spi-only-use-cs1-sel
spi: stm32: always perform registers configuration prior to transfer
spi: stm32: fixes suspend/resume management
spi: stm32: fix stm32_spi_prepare_mbr in case of odd clk_rate
spi: stm32: fix fifo threshold level in case of short transfer
spi: stm32h7: fix race condition at end of transfer
spi: stm32: clear only asserted irq flags on interrupt
spi: Prevent adding devices below an unregistering controller
Correct the kerneldoc for structure to fix W=1 compile warning:
drivers/spi/spi-s3c24xx.c:36: warning: cannot understand function prototype: 'struct s3c24xx_spi_devstate '
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Andi Shyti <andi@etezian.org>
Link: https://lore.kernel.org/r/20200804151356.28057-1-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Set DMA transfer mode for ColdFire.
After recent fixes to fsl edma engine, this mode can be used
also for ColdFire, and from some raw mtd r/w tests it definitely
improves the transfer rate, so keeping it selected.
Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Link: https://lore.kernel.org/r/20200816094635.1830006-1-angelo.dureghello@timesys.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use __maybe_unused for the suspend()/resume() hooks and get rid of
the CONFIG_PM_SLEEP ifdefery to improve the code.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20200817235812.19518-1-festevam@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI registers content may have been lost upon suspend/resume sequence.
So, always compute and apply the necessary configuration in
stm32_spi_transfer_one_setup routine.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Link: https://lore.kernel.org/r/1597043558-29668-6-git-send-email-alain.volmat@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds pinctrl power management, and reconfigure spi controller
in case of resume.
Fixes: 038ac869c9 ("spi: stm32: add runtime PM support")
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Link: https://lore.kernel.org/r/1597043558-29668-5-git-send-email-alain.volmat@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix spi->clk_rate when it is odd to the nearest lowest even value because
minimum SPI divider is 2.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Link: https://lore.kernel.org/r/1597043558-29668-4-git-send-email-alain.volmat@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When transfer is shorter than half of the fifo, set the data packet size
up to transfer size instead of up to half of the fifo.
Check also that threshold is set at least to 1 data frame.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Link: https://lore.kernel.org/r/1597043558-29668-3-git-send-email-alain.volmat@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The caller of stm32_spi_transfer_one(), spi_transfer_one_message(),
is waiting for us to call spi_finalize_current_transfer() and will
eventually schedule a new transfer, if available.
We should guarantee that the spi controller is really available
before calling spi_finalize_current_transfer().
Move the call to spi_finalize_current_transfer() _after_ the call
to stm32_spi_disable().
Signed-off-by: Antonio Borneo <antonio.borneo@st.com>
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Link: https://lore.kernel.org/r/1597043558-29668-2-git-send-email-alain.volmat@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This became wide and scattered updates all over the sound tree as
diffstat shows: lots of (still ongoing) refactoring works in ASoC,
fixes and cleanups caught by static analysis, inclusive term
conversions as well as lots of new drivers. Below are highlights:
ASoC core:
* API cleanups and conversions to the unified mute_stream() call
* Simplify I/O helper functions
* Use helper macros to retrieve RTD from substreams
ASoC drivers:
* Lots of fixes and cleanups in Intel ASoC drivers
* Lots of new stuff: Freescale MQS and i.MX6sx, Intel KeemBay I2S,
Maxim MAX98360A and MAX98373 SoundWire, various Mediatek boards,
nVidia Tegra 186 and 210, RealTek RL6231, Samsung Midas and Aries
boards, TI J721e EVM
ALSA core:
* Minor code refacotring for SG-buffer handling
HD-audio:
* Generalization of mute-LED handling with LED classdev
* Intel silent stream support for HDMI
* Device-specific fixes: CA0132, Loongson-3
Others:
* Usual USB- and HD-audio quirks for various devices
* Fixes for echoaudio DMA position handling
* Various documents and trivial fixes for sparse warnings
* Conversion to adapt inclusive terms
-----BEGIN PGP SIGNATURE-----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=sy7n
-----END PGP SIGNATURE-----
Merge tag 'sound-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This became wide and scattered updates all over the sound tree as
diffstat shows: lots of (still ongoing) refactoring works in ASoC,
fixes and cleanups caught by static analysis, inclusive term
conversions as well as lots of new drivers. Below are highlights:
ASoC core:
- API cleanups and conversions to the unified mute_stream() call
- Simplify I/O helper functions
- Use helper macros to retrieve RTD from substreams
ASoC drivers:
- Lots of fixes and cleanups in Intel ASoC drivers
- Lots of new stuff: Freescale MQS and i.MX6sx, Intel KeemBay I2S,
Maxim MAX98360A and MAX98373 SoundWire, various Mediatek boards,
nVidia Tegra 186 and 210, RealTek RL6231, Samsung Midas and Aries
boards, TI J721e EVM
ALSA core:
- Minor code refacotring for SG-buffer handling
HD-audio:
- Generalization of mute-LED handling with LED classdev
- Intel silent stream support for HDMI
- Device-specific fixes: CA0132, Loongson-3
Others:
- Usual USB- and HD-audio quirks for various devices
- Fixes for echoaudio DMA position handling
- Various documents and trivial fixes for sparse warnings
- Conversion to adopt inclusive terms"
* tag 'sound-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (479 commits)
ALSA: pci: delete repeated words in comments
ALSA: isa: delete repeated words in comments
ALSA: hda/tegra: Add 100us dma stop delay
ALSA: hda: Add dma stop delay variable
ASoC: hda/tegra: Set buffer alignment to 128 bytes
ALSA: seq: oss: Serialize ioctls
ALSA: hda/hdmi: Add quirk to force connectivity
ALSA: usb-audio: add startech usb audio dock name
ALSA: usb-audio: Add support for Lenovo ThinkStation P620
Revert "ALSA: hda: call runtime_allow() for all hda controllers"
ALSA: hda/ca0132 - Fix AE-5 microphone selection commands.
ALSA: hda/ca0132 - Add new quirk ID for Recon3D.
ALSA: hda/ca0132 - Fix ZxR Headphone gain control get value.
ALSA: hda/realtek: Add alc269/alc662 pin-tables for Loongson-3 laptops
ALSA: docs: fix typo
ALSA: doc: use correct config variable name
ASoC: core: Two step component registration
ASoC: core: Simplify snd_soc_component_initialize declaration
ASoC: core: Relocate and expose snd_soc_component_initialize
ASoC: sh: Replace 'select' DMADEVICES 'with depends on'
...
static priority level knowledge from non-scheduler code.
The three APIs for non-scheduler code to set SCHED_FIFO are:
- sched_set_fifo()
- sched_set_fifo_low()
- sched_set_normal()
These are two FIFO priority levels: default (high), and a 'low' priority level,
plus sched_set_normal() to set the policy back to non-SCHED_FIFO.
Since the changes affect a lot of non-scheduler code, we kept this in a separate
tree.
When merging to the latest upstream tree there's a conflict in drivers/spi/spi.c,
which can be resolved via:
sched_set_fifo(ctlr->kworker_task);
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=/7JH
-----END PGP SIGNATURE-----
Merge tag 'sched-fifo-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull sched/fifo updates from Ingo Molnar:
"This adds the sched_set_fifo*() encapsulation APIs to remove static
priority level knowledge from non-scheduler code.
The three APIs for non-scheduler code to set SCHED_FIFO are:
- sched_set_fifo()
- sched_set_fifo_low()
- sched_set_normal()
These are two FIFO priority levels: default (high), and a 'low'
priority level, plus sched_set_normal() to set the policy back to
non-SCHED_FIFO.
Since the changes affect a lot of non-scheduler code, we kept this in
a separate tree"
* tag 'sched-fifo-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
sched,tracing: Convert to sched_set_fifo()
sched: Remove sched_set_*() return value
sched: Remove sched_setscheduler*() EXPORTs
sched,psi: Convert to sched_set_fifo_low()
sched,rcutorture: Convert to sched_set_fifo_low()
sched,rcuperf: Convert to sched_set_fifo_low()
sched,locktorture: Convert to sched_set_fifo()
sched,irq: Convert to sched_set_fifo()
sched,watchdog: Convert to sched_set_fifo()
sched,serial: Convert to sched_set_fifo()
sched,powerclamp: Convert to sched_set_fifo()
sched,ion: Convert to sched_set_normal()
sched,powercap: Convert to sched_set_fifo*()
sched,spi: Convert to sched_set_fifo*()
sched,mmc: Convert to sched_set_fifo*()
sched,ivtv: Convert to sched_set_fifo*()
sched,drm/scheduler: Convert to sched_set_fifo*()
sched,msm: Convert to sched_set_fifo*()
sched,psci: Convert to sched_set_fifo*()
sched,drbd: Convert to sched_set_fifo*()
...
Previously the stm32h7 interrupt thread cleared all non-masked interrupts.
If an interrupt was to occur during the handling of another interrupt its
flag would be unset, resulting in a lost interrupt.
This patches fixes the issue by clearing only the currently set interrupt
flags.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Link: https://lore.kernel.org/r/20200804195136.1485392-1-t.schramm@manjaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
A fairly quiet release for SPI, nothing really going on in the core
although there's been quite a bit of driver related activity. This pull
request includes the addition of some shared code in drivers/memory for
the Renesas RPC-IF which is used by a newly added SPI driver, the memory
subsystem doesn't seem to have a fixed maintainer at the minute and this
seemed like the most sensible way to get that hardware supported.
- Quite a few cleanups and optimizations for the Altera, Qualcomm GENI,
sun6i and lantiq drivers.
- Several more GPIO descriptor conversions.
- Move the Cadence QuadSPI driver from drivers/mtd to drivers/spi.
- New support for Mediatek MT8192 and Renesas RPC-IF, R8A7742 and
R8A774e1.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl8oBFoTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0P2UB/47NlDsAadOiOB0ZzPKdn4Nr5BLvUza
TP63gAsxD4BErzgf/p/0D8qUTZPzmlfA833gj9hkIavJlTmv3fGrH0XeHg2OuCJb
yhyw9pE7MPpnARVOJHz1MZkAT/dY+sF3TaUXysmymlvs6CLqRnsLTOwK2f92SeGH
ygpC4J1tfD961xWmv2Zt8wNuQXtH+JePLXeZFSx2ZkpToFT56QO6kFpWjVfDquY4
/F8bc7qyXX6FcsBYAG6Ly35OSxbPazVLkTaDWQr5V4TAD0DXw0NOyvxg2OccqE31
y1jjx3hn98sN73m/VLzlEOer4w9313K5BOISaN0z7TQSQ55XRZKe4EQj
=K1PB
-----END PGP SIGNATURE-----
Merge tag 'spi-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A fairly quiet release for SPI, nothing really going on in the core
although there's been quite a bit of driver related activity.
This includes the addition of some shared code in drivers/memory for
the Renesas RPC-IF which is used by a newly added SPI driver, the
memory subsystem doesn't seem to have a fixed maintainer at the minute
and this seemed like the most sensible way to get that hardware
supported.
- Quite a few cleanups and optimizations for the Altera, Qualcomm
GENI, sun6i and lantiq drivers.
- Several more GPIO descriptor conversions.
- Move the Cadence QuadSPI driver from drivers/mtd to drivers/spi.
- New support for Mediatek MT8192 and Renesas RPC-IF, R8A7742 and
R8A774e1"
* tag 'spi-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (119 commits)
dt-bindings: lpspi: New property in document DT bindings for LPSPI
spi: lpspi: fix using CS discontinuously on i.MX8DXLEVK
spi: lpspi: remove unused fsl_lpspi->chipselect
spi: lpspi: Fix kernel warning dump when probe fail after calling spi_register
spi: rockchip: Fix error in SPI slave pio read
spi: rockchip: Support 64-location deep FIFOs
spi: rockchip: Config spi rx dma burst size depend on xfer length
spi: spi-topcliff-pch: drop call to wakeup-disable
spi: spidev: Align buffers for DMA
spi: correct kernel-doc inconsistency
spi: sun4i: update max transfer size reported
spi: imx: enable runtime pm support
spi: update bindings for MT8192 SoC
spi: mediatek: add spi support for mt8192 IC
spi: Add bindings for Lightning Mountain SoC
spi: lantiq: Add support to Lightning Mountain SoC
spi: lantiq: Move interrupt configuration to SoC specific data structure
spi: lantiq: Add fifo size bit mask in SoC specific data structure
spi: lantiq: Add support to acknowledge interrupt
spi: lantiq: Move interrupt control register offesets to SoC specific data structure
...
A couple of subsystems have their own subsystem maintainers but choose
to have the code merged through the soc tree as upstream, as the code
tends to be used across multiple SoCs or has SoC specific drivers itself:
- memory controllers:
Krzysztof Kozlowski takes ownership of the drivers/memory
subsystem and its drivers, starting out with a set of cleanup
patches.
A larger driver for the Tegra memory controller that was accidentally
missed for v5.8 is now added.
- reset controllers:
Only minor updates to drivers/reset this time
- firmware:
The "turris mox" firmware driver gains support for signed firmware blobs
The tegra firmware driver gets extended to export some debug information
Various updates to i.MX firmware drivers, mostly cosmetic
- ARM SCMI/SCPI:
A new mechanism for platform notifications is added, among a number
of minor changes.
- optee:
Probing of the TEE bus is rewritten to better support detection of
devices that depend on the tee-supplicant user space.
A new firmware based trusted platform module (fTPM) driver is added
based on OP-TEE
- SoC attributes:
A new driver is added to provide a generic soc_device for identifying
a machine through the SMCCC ARCH_SOC_ID firmware interface rather than
by probing SoC family specific registers.
The series also contains some cleanups to the common soc_device code.
There are also a number of updates to SoC specific drivers,
the main ones are:
- Mediatek cmdq driver gains a few in-kernel interfaces
- Minor updates to Qualcomm RPMh, socinfo, rpm drivers, mostly adding
support for additional SoC variants
- The Qualcomm GENI core code gains interconnect path voting and
performance level support, and integrating this into a number of
device drivers.
- A new driver for Samsung Exynos5800 voltage coupler for
- Renesas RZ/G2H (R8A774E1) SoC support gets added to a couple of SoC
specific device drivers
- Updates to the TI K3 Ring Accelerator driver
-----BEGIN PGP SIGNATURE-----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=nezz
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"A couple of subsystems have their own subsystem maintainers but choose
to have the code merged through the soc tree as upstream, as the code
tends to be used across multiple SoCs or has SoC specific drivers
itself:
- memory controllers:
Krzysztof Kozlowski takes ownership of the drivers/memory subsystem
and its drivers, starting out with a set of cleanup patches.
A larger driver for the Tegra memory controller that was
accidentally missed for v5.8 is now added.
- reset controllers:
Only minor updates to drivers/reset this time
- firmware:
The "turris mox" firmware driver gains support for signed firmware
blobs The tegra firmware driver gets extended to export some debug
information Various updates to i.MX firmware drivers, mostly
cosmetic
- ARM SCMI/SCPI:
A new mechanism for platform notifications is added, among a number
of minor changes.
- optee:
Probing of the TEE bus is rewritten to better support detection of
devices that depend on the tee-supplicant user space. A new
firmware based trusted platform module (fTPM) driver is added based
on OP-TEE
- SoC attributes:
A new driver is added to provide a generic soc_device for
identifying a machine through the SMCCC ARCH_SOC_ID firmware
interface rather than by probing SoC family specific registers.
The series also contains some cleanups to the common soc_device
code.
There are also a number of updates to SoC specific drivers, the main
ones are:
- Mediatek cmdq driver gains a few in-kernel interfaces
- Minor updates to Qualcomm RPMh, socinfo, rpm drivers, mostly adding
support for additional SoC variants
- The Qualcomm GENI core code gains interconnect path voting and
performance level support, and integrating this into a number of
device drivers.
- A new driver for Samsung Exynos5800 voltage coupler for
- Renesas RZ/G2H (R8A774E1) SoC support gets added to a couple of SoC
specific device drivers
- Updates to the TI K3 Ring Accelerator driver"
* tag 'arm-drivers-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (164 commits)
soc: qcom: geni: Fix unused label warning
soc: qcom: smd-rpm: Fix kerneldoc
memory: jz4780_nemc: Only request IO memory the driver will use
soc: qcom: pdr: Reorder the PD state indication ack
MAINTAINERS: Add Git repository for memory controller drivers
memory: brcmstb_dpfe: Fix language typo
memory: samsung: exynos5422-dmc: Correct white space issues
memory: samsung: exynos-srom: Correct alignment
memory: pl172: Enclose macro argument usage in parenthesis
memory: of: Correct kerneldoc
memory: omap-gpmc: Fix language typo
memory: omap-gpmc: Correct white space issues
memory: omap-gpmc: Use 'unsigned int' for consistency
memory: omap-gpmc: Enclose macro argument usage in parenthesis
memory: omap-gpmc: Correct kerneldoc
memory: mvebu-devbus: Align with open parenthesis
memory: mvebu-devbus: Add missing braces to all arms of if statement
memory: bt1-l2-ctl: Add blank lines after declarations
soc: TI knav_qmss: make symbol 'knav_acc_range_ops' static
firmware: ti_sci: Replace HTTP links with HTTPS ones
...
CONFIG_OF_DYNAMIC and CONFIG_ACPI allow adding SPI devices at runtime
using a DeviceTree overlay or DSDT patch. CONFIG_SPI_SLAVE allows the
same via sysfs.
But there are no precautions to prevent adding a device below a
controller that's being removed. Such a device is unusable and may not
even be able to unbind cleanly as it becomes inaccessible once the
controller has been torn down. E.g. it is then impossible to quiesce
the device's interrupt.
of_spi_notify() and acpi_spi_notify() do hold a ref on the controller,
but otherwise run lockless against spi_unregister_controller().
Fix by holding the spi_add_lock in spi_unregister_controller() and
bailing out of spi_add_device() if the controller has been unregistered
concurrently.
Fixes: ce79d54ae4 ("spi/of: Add OF notifier handler")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.19+
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Octavian Purdila <octavian.purdila@intel.com>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Link: https://lore.kernel.org/r/a8c3205088a969dc8410eec1eba9aface60f36af.1596451035.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI common code does not support using CS discontinuously for now.
However, i.MX8DXL-EVK only uses CS1 without CS0. Therefore, add a flag
is_only_cs1 to set the correct TCR[PCS].
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Link: https://lore.kernel.org/r/20200727031448.31661-4-xiaoning.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The RXFLR is possible larger than rx_left in Rockchip SPI, fix it.
Fixes: 01b59ce5da ("spi: rockchip: use irq rather than polling")
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Tested-by: Emil Renner Berthing <kernel@esmil.dk>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20200723004356.6390-3-jon.lin@rock-chips.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The FIFO depth of SPI V2 is 64 instead of 32, add support for it.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Tested-by: Emil Renner Berthing <kernel@esmil.dk>
Reviewed-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20200723004356.6390-2-jon.lin@rock-chips.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The burst length can be adjusted according to the transmission
length to improve the transmission rate
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Tested-by: Emil Renner Berthing <kernel@esmil.dk>
Reviewed-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20200723004356.6390-1-jon.lin@rock-chips.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Before generic upgrade, both .suspend() and .resume() were invoking
pci_enable_wake(pci_dev, PCI_D3hot, 0). Hence, disabling wakeup in both
states. (Normal trend is .suspend() enables and .resume() disables the
wakeup.)
This was ambiguous and may be buggy. Instead of replicating the legacy
behavior, drop the wakeup-disable call.
Fixes: f185bcc779 ("spi: spi-topcliff-pch: use generic power management")
Reported-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200727172936.661567-1-vaibhavgupta40@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Simply copying all xfers from userspace into one bounce buffer causes
alignment problems if the SPI controller uses DMA.
Ensure that all transfer data blocks within the rx and tx bounce buffers
are aligned for DMA (according to ARCH_KMALLOC_MINALIGN).
Alignment may increase the usage of the bounce buffers. In some cases,
the buffers may need to be increased using the "bufsiz" module
parameter.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200728100832.24788-1-ceggers@arri.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi-sun4i driver already has the ability to do large transfers.
However, the max transfer size reported is still fifo depth - 1.
Update the max transfer size reported to the max value possible.
Fixes: 196737912d ("spi: sun4i: Allow transfers larger than FIFO size")
Signed-off-by: Jonathan Liu <net147@gmail.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20200727072328.510798-1-net147@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Drivers using legacy PM have to manage PCI states and device's PM states
themselves. They also need to take care of configuration registers.
With improved and powerful support of generic PM, PCI Core takes care of
above mentioned, device-independent, jobs.
This driver makes use of PCI helper functions like
pci_save/restore_state(), pci_enable/disable_device(), pci_enable_wake()
and pci_set_power_state() to do required operations. In generic mode, they
are no longer needed.
Change function parameter in both .suspend() and .resume() to
"struct device*" type. Use dev_get_drvdata() to get drv data.
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Link: https://lore.kernel.org/r/20200720155714.714114-1-vaibhavgupta40@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This converts the PPC4xx SPI driver to use GPIO descriptors.
The driver is already just picking some GPIOs from the device
tree so the conversion is pretty straight forward. However
this driver is looking form a pure "gpios" property rather
than the standard binding "cs-gpios" so we need to add a new
exception to the gpiolib OF parser to allow this for this
driver's compatibles.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linuxppc-dev@lists.ozlabs.org
Link: https://lore.kernel.org/r/20200714072226.26071-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi cadence driver should support spi-cs-high in mode bits
so that the peripherals that needs the chip select to be high active can
use it. Add the SPI-CS-HIGH flag in the supported mode bits.
Signed-off-by: Shreyas Joshi <shreyas.joshi@biamp.com>
Link: https://lore.kernel.org/r/20200710211655.1564-1-shreyas.joshi@biamp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Call the put function after probe successfully. Otherwise, the lpspi
module will keep active status until the first spi transfer called.
Disable runtime pm when probe fails. There is no need to active runtime
pm after probe failed.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Link: https://lore.kernel.org/r/20200714075251.12777-2-xiaoning.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It turns out having a Rx DMA channel serviced with higher priority than
a Tx DMA channel is not enough to provide a well balanced DMA-based SPI
transfer interface. There might still be moments when the Tx DMA channel
is occasionally handled faster than the Rx DMA channel. That in its turn
will eventually cause the SPI Rx FIFO overflow if SPI bus speed is high
enough to fill the SPI Rx FIFO in before it's cleared by the Rx DMA
channel. That's why having the DMA-based SPI Tx interface too optimized
is the errors prone, so the commit 0b2b66514f ("spi: dw: Use DMA max
burst to set the request thresholds") though being perfectly normal from
the standard functionality point of view implicitly introduced the problem
described above. In order to fix that the Tx DMA activity is intentionally
slowed down by limiting the SPI Tx FIFO depth with a value twice bigger
than the Tx burst length calculated earlier by the
dw_spi_dma_maxburst_init() method.
Fixes: 0b2b66514f ("spi: dw: Use DMA max burst to set the request thresholds")
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Feng Tang <feng.tang@intel.com>
Link: https://lore.kernel.org/r/20200721203951.2159-1-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
The lantiq-ssc driver uses internally an own workqueue to wait till the
data is not only written out of the FIFO but really written to the wire.
This workqueue is flushed while the SPI subsystem is working in some
other system workqueue.
The system workqueue is marked as WQ_MEM_RECLAIM, but the workqueue in
the lantiq-ssc driver does not use WQ_MEM_RECLAIM for now. Add this flag
too to prevent this warning.
This fixes the following warning:
[ 2.975956] WARNING: CPU: 1 PID: 17 at kernel/workqueue.c:2614 check_flush_dependency+0x168/0x184
[ 2.984752] workqueue: WQ_MEM_RECLAIM kblockd:blk_mq_run_work_fn is flushing !WQ_MEM_RECLAIM 1e100800.spi:0x0
Fixes: 891b7c5fbf ("mtd_blkdevs: convert to blk-mq")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://lore.kernel.org/r/20200717215648.20522-1-hauke@hauke-m.de
Signed-off-by: Mark Brown <broonie@kernel.org>
A couple of small driver specific fixes for fairly minor issues.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl8Rl3ETHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0DrYCACFJjlpdg7+LFK+zoQwIY9JPFd/VQWD
X0xxnpJVxBRwyoAFbjfN0TfEg4lZ7KtbOBt91T7MaxUTtLet6KSuf+1ADuZSKe4Y
K9eb1i+J1zjYzkVTDhlSCmIUIVOufZqxGPSQjuPjQhbOyT+SjyfyQhrJ0Atof8gb
EyyrkQjwiC6y6xW0TpxEcrC4Toku5Si2YbH8RkOgH3puaZ03wVzLxNNeDxPPUFSh
uu6IvXuzE+6p1MlTF13nd4TFkFRu1QNUVPL7PRlXvU9a1YtYzxp6tPYlOtnWvrER
vh2u2QfR90LeVy+r7RizJO7bfBy90H7yB8qKRPOPn3v2UhImYDEwfqtm
=zprr
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v5.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi into master
Pull spi fixes from Mark Brown:
"A couple of small driver specific fixes for fairly minor issues"
* tag 'spi-fix-v5.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi-sun6i: sun6i_spi_transfer_one(): fix setting of clock rate
spi: mediatek: use correct SPI_CFG2_REG MACRO
Since ACPI_PTR() is used to NULLify the value when !CONFIG_ACPI,
struct 'spi_acpi_match' becomes defined but unused.
Fixes the following W=1 kernel build warning(s):
drivers/spi/spi-amd.c:297:36: warning: ‘spi_acpi_match’ defined but not used [-Wunused-const-variable=]
297 | static const struct acpi_device_id spi_acpi_match[] = {
| ^~~~~~~~~~~~~~
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Sanjay R Mehta <sanju.mehta@amd.com>
Link: https://lore.kernel.org/r/20200717135424.2442271-15-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Since ACPI_PTR() is used to NULLify the value when !CONFIG_ACPI,
struct 'pxa2xx_spi_acpi_match' becomes defined but unused.
Fixes the following W=1 kernel build warning(s):
drivers/spi/spi-pxa2xx.c:1435:36: warning: ‘pxa2xx_spi_acpi_match’ defined but not used [-Wunused-const-variable=]
1435 | static const struct acpi_device_id pxa2xx_spi_acpi_match[] = {
| ^~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Link: https://lore.kernel.org/r/20200717135424.2442271-14-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The only way this driver can be probed by MFD via its parent device.
No other reference to 'microchip,at91sam9g45-usart-spi' exists in the kernel.
Fixes the following W=1 kernel build warning(s):
drivers/spi/spi-at91-usart.c:684:34: warning: ‘at91_usart_spi_dt_ids’ defined but not used [-Wunused-const-variable=]
684 | static const struct of_device_id at91_usart_spi_dt_ids[] = {
| ^~~~~~~~~~~~~~~~~~~~~
Suggested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Radu Pirea <radu_nicolae.pirea@upb.ro>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20200717135424.2442271-13-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/spi/spi-topcliff-pch.c:184: warning: Function parameter or member 'io_base_addr' not described in 'pch_spi_data'
drivers/spi/spi-topcliff-pch.c:184: warning: Function parameter or member 'pkt_tx_buff' not described in 'pch_spi_data'
drivers/spi/spi-topcliff-pch.c:184: warning: Function parameter or member 'pkt_rx_buff' not described in 'pch_spi_data'
drivers/spi/spi-topcliff-pch.c:184: warning: Function parameter or member 'dma' not described in 'pch_spi_data'
drivers/spi/spi-topcliff-pch.c:184: warning: Function parameter or member 'use_dma' not described in 'pch_spi_data'
drivers/spi/spi-topcliff-pch.c:184: warning: Function parameter or member 'save_total_len' not described in 'pch_spi_data'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200717135424.2442271-12-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/spi/spi-zynqmp-gqspi.c:205: warning: Function parameter or member 'slavecs' not described in 'zynqmp_gqspi_selectslave'
drivers/spi/spi-zynqmp-gqspi.c:205: warning: Function parameter or member 'slavebus' not described in 'zynqmp_gqspi_selectslave'
drivers/spi/spi-zynqmp-gqspi.c:205: warning: Excess function parameter 'flashcs' description in 'zynqmp_gqspi_selectslave'
drivers/spi/spi-zynqmp-gqspi.c:205: warning: Excess function parameter 'flashbus' description in 'zynqmp_gqspi_selectslave'
drivers/spi/spi-zynqmp-gqspi.c:902: warning: Function parameter or member 'dev' not described in 'zynqmp_qspi_suspend'
drivers/spi/spi-zynqmp-gqspi.c:902: warning: Excess function parameter '_dev' description in 'zynqmp_qspi_suspend'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/20200717135424.2442271-11-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/spi/spi-zynq-qspi.c:143: warning: Function parameter or member 'dev' not described in 'zynq_qspi'
drivers/spi/spi-zynq-qspi.c:334: warning: Function parameter or member 'spi' not described in 'zynq_qspi_config_op'
drivers/spi/spi-zynq-qspi.c:334: warning: Excess function parameter 'qspi' description in 'zynq_qspi_config_op'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Cc: Sureshkumar Relli <nagasure@xilinx.com>
Link: https://lore.kernel.org/r/20200717135424.2442271-10-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Also demote non-worthy kerneldoc headers to standard comment blocks.
Fixes the following W=1 kernel build warning(s):
drivers/spi/spi-pl022.c:304: warning: cannot understand function prototype: 'enum ssp_writing '
drivers/spi/spi-pl022.c:330: warning: Function parameter or member 'loopback' not described in 'vendor_data'
drivers/spi/spi-pl022.c:398: warning: Function parameter or member 'rx_lev_trig' not described in 'pl022'
drivers/spi/spi-pl022.c:398: warning: Function parameter or member 'tx_lev_trig' not described in 'pl022'
drivers/spi/spi-pl022.c:398: warning: Function parameter or member 'dma_running' not described in 'pl022'
drivers/spi/spi-pl022.c:670: warning: Function parameter or member 'pl022' not described in 'readwriter'
drivers/spi/spi-pl022.c:1250: warning: Function parameter or member 'irq' not described in 'pl022_interrupt_handler'
drivers/spi/spi-pl022.c:1250: warning: Function parameter or member 'dev_id' not described in 'pl022_interrupt_handler'
drivers/spi/spi-pl022.c:1343: warning: Function parameter or member 'pl022' not described in 'set_up_next_transfer'
drivers/spi/spi-pl022.c:1343: warning: Function parameter or member 'transfer' not described in 'set_up_next_transfer'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Sachin Verma <sachin.verma@st.com>
Link: https://lore.kernel.org/r/20200717135424.2442271-9-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/spi/spi-s3c64xx.c:150: warning: Function parameter or member 'quirks' not described in 's3c64xx_spi_port_config'
drivers/spi/spi-s3c64xx.c:150: warning: Function parameter or member 'clk_ioclk' not described in 's3c64xx_spi_port_config'
drivers/spi/spi-s3c64xx.c:189: warning: Function parameter or member 'pdev' not described in 's3c64xx_spi_driver_data'
drivers/spi/spi-s3c64xx.c:189: warning: Function parameter or member 'rx_dma' not described in 's3c64xx_spi_driver_data'
drivers/spi/spi-s3c64xx.c:189: warning: Function parameter or member 'tx_dma' not described in 's3c64xx_spi_driver_data'
drivers/spi/spi-s3c64xx.c:189: warning: Function parameter or member 'port_conf' not described in 's3c64xx_spi_driver_data'
drivers/spi/spi-s3c64xx.c:189: warning: Function parameter or member 'port_id' not described in 's3c64xx_spi_driver_data'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Andi Shyti <andi@etezian.org>
Cc: Jaswinder Singh <jassi.brar@samsung.com>
Cc: linux-samsung-soc@vger.kernel.org
Link: https://lore.kernel.org/r/20200717135424.2442271-8-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Looks like it hasn't ever been checked.
Fixes the following W=1 kernel build warning(s):
drivers/spi/spi-meson-spicc.c: In function ‘meson_spicc_reset_fifo’:
drivers/spi/spi-meson-spicc.c:365:6: warning: variable ‘data’ set but not used [-Wunused-but-set-variable]
365 | u32 data;
| ^~~~
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: linux-amlogic@lists.infradead.org
Link: https://lore.kernel.org/r/20200717135424.2442271-7-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/spi/spi-meson-spifc.c:80: warning: Function parameter or member 'dev' not described in 'meson_spifc'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Beniamino Galvani <b.galvani@gmail.com>
Cc: linux-amlogic@lists.infradead.org
Link: https://lore.kernel.org/r/20200717135424.2442271-6-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
ep93xx_spi_read_write() changed is parameters, but the function
documentation was left unchanged. Let's realign.
Fixes the following W=1 kernel build warning(s):
drivers/spi/spi-ep93xx.c:227: warning: Function parameter or member 'master' not described in 'ep93xx_spi_read_write'
drivers/spi/spi-ep93xx.c:227: warning: Excess function parameter 'espi' description in 'ep93xx_spi_read_write'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Mika Westerberg <mika.westerberg@iki.fi>
Link: https://lore.kernel.org/r/20200717135424.2442271-5-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/spi/spi-davinci.c:249: warning: Function parameter or member 'dspi' not described in 'davinci_spi_get_prescale'
drivers/spi/spi-davinci.c:249: warning: Function parameter or member 'max_speed_hz' not described in 'davinci_spi_get_prescale'
drivers/spi/spi-davinci.c:249: warning: Excess function parameter 'maxspeed_hz' description in 'davinci_spi_get_prescale'
drivers/spi/spi-davinci.c:719: warning: Function parameter or member 'data' not described in 'dummy_thread_fn'
drivers/spi/spi-davinci.c:719: warning: Excess function parameter 'context_data' description in 'dummy_thread_fn'
drivers/spi/spi-davinci.c:735: warning: Function parameter or member 'data' not described in 'davinci_spi_irq'
drivers/spi/spi-davinci.c:735: warning: Excess function parameter 'context_data' description in 'davinci_spi_irq'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200717135424.2442271-4-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
No attempt has been made to document any of the demoted functions here.
Fixes the following W=1 kernel build warning(s):
drivers/spi/spi-bitbang.c:181: warning: Function parameter or member 'spi' not described in 'spi_bitbang_setup'
drivers/spi/spi-bitbang.c:215: warning: Function parameter or member 'spi' not described in 'spi_bitbang_cleanup'
drivers/spi/spi-bitbang.c:434: warning: Function parameter or member 'bitbang' not described in 'spi_bitbang_stop'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200717135424.2442271-3-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Kerneldoc function parameter descriptions must be in '@.*: ' format.
Fixes the following W=1 kernel build warning(s):
drivers/spi/spi-loopback-test.c:897: warning: Function parameter or member 'spi' not described in 'spi_test_execute_msg'
drivers/spi/spi-loopback-test.c:897: warning: Function parameter or member 'test' not described in 'spi_test_execute_msg'
drivers/spi/spi-loopback-test.c:897: warning: Function parameter or member 'tx' not described in 'spi_test_execute_msg'
drivers/spi/spi-loopback-test.c:897: warning: Function parameter or member 'rx' not described in 'spi_test_execute_msg'
drivers/spi/spi-loopback-test.c:970: warning: Function parameter or member 'spi' not described in 'spi_test_run_test'
drivers/spi/spi-loopback-test.c:970: warning: Function parameter or member 'test' not described in 'spi_test_run_test'
drivers/spi/spi-loopback-test.c:970: warning: Function parameter or member 'tx' not described in 'spi_test_run_test'
drivers/spi/spi-loopback-test.c:970: warning: Function parameter or member 'rx' not described in 'spi_test_run_test'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Martin Sperl <kernel@martin.sperl.org>
Cc: linux-spi@vger.kernel.org
Link: https://lore.kernel.org/r/20200717135424.2442271-2-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Hello,
I've picked up and forward ported Martin Sperl's patches which add support for
effective_speed_hz to the SPI controllers found on all raspberry pi models.
See the following patch, which adds this feature to the SPI core, for more
information:
5d7e2b5ed5 spi: core: allow reporting the effectivly used speed_hz for a transfer
regards,
Marc
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Optimezed mem*io operations are defined for LE platforms, use them.
The ARM and !ARCH_EBSA110 dependencies for COMPILE_TEST were added
only for the _memcpy_fromio()/_memcpy_toio() functions. Drop these
dependencies.
Tested unaligned accesses on both sama5d2 and sam9x60 QSPI controllers
using SPI NOR flashes, everything works ok. The following performance
improvement can be seen when running mtd_speedtest:
sama5d2_xplained (mx25l25635e)
- before:
mtd_speedtest: eraseblock write speed is 983 KiB/s
mtd_speedtest: eraseblock read speed is 6150 KiB/s
- after:
mtd_speedtest: eraseblock write speed is 1055 KiB/s
mtd_speedtest: eraseblock read speed is 20144 KiB/s
sam9x60ek (sst26vf064b)
- before:
mtd_speedtest: eraseblock write speed is 4770 KiB/s
mtd_speedtest: eraseblock read speed is 8062 KiB/s
- after:
mtd_speedtest: eraseblock write speed is 4524 KiB/s
mtd_speedtest: eraseblock read speed is 21186 KiB/s
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200716043139.565734-1-tudor.ambarus@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently we always defer idling of controllers to the SPI thread, the goal
being to ensure that we're doing teardown that's not suitable for atomic
context in an appropriate context and to try to batch up more expensive
teardown operations when the system is under higher load, allowing more
work to be started before the SPI thread is scheduled. However when the
controller does not require any substantial work to idle there is no need
to do this, we can instead save the context switch and immediately mark
the controller as idle. This is particularly useful for systems where there
is frequent but not constant activity.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20200715163610.9475-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Setting spi_transfer->effective_speed_hz in transfer_one so that
it can get used in cs_change_delay configured with delay as a muliple
of SPI clock cycles.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20200709074120.110069-3-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Setting spi_transfer->effective_speed_hz in transfer_one so that
it can get used in cs_change_delay configured with delay as a muliple
of SPI clock cycles.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20200709074120.110069-2-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Hi,
This series adds support for octal DTR flashes in the spi-nor framework,
and then adds hooks for the Cypress Semper and Mircom Xcella flashes to
allow running them in octal DTR mode. This series assumes that the flash
is handed to the kernel in Legacy SPI mode.
Tested on TI J721e EVM with 1-bit ECC on the Cypress flash.
Changes in v10:
- Rebase on latest linux-next/master. Drop a couple patches that made it
in the previous release.
- Move the code that sets 20 dummy cycles for MT35XU512ABA to its octal
enable function. This way, if the controller doesn't support 8D mode
20 dummy cycles won't be used.
Changes in v9:
- Do not use '& 0xff' to get the opcode LSB in spi-mxic and
spi-zynq-qspi. The cast to u8 will do that anyway.
- Do not use if (opcode) as a check for whether the command phase exists
in spi-zynq-qspi because the opcode 0 can be valid. Use the new
cmd.nbytes instead.
Changes in v8:
- Move controller changes in spi-mxic to the commit which introduces
2-byte opcodes to avoid problems when bisecting.
- Replace usage of sizeof(op->cmd.opcode) with op->cmd.nbytes.
- Extract opcode in spi-zynq-qspi instead of using &op->cmd.opcode.
Changes in v7:
- Reject ops with more than 1 command byte in
spi_mem_default_supports_op().
- Reject ops with more than 1 command byte in atmel and mtk controllers.
- Reject ops with 0 command bytes in spi_mem_check_op().
- Set cmd.nbytes to 1 when using SPI_MEM_OP_CMD().
- Avoid endianness problems in spi-mxic.
Changes in v6:
- Instead of hard-coding 8D-8D-8D Fast Read dummy cycles to 20, find
them out from the Profile 1.0 table.
Changes in v5:
- Do not enable stateful X-X-X modes if the reset line is broken.
- Instead of setting SNOR_READ_HWCAPS_8_8_8_DTR from Profile 1.0 table
parsing, do it in spi_nor_info_init_params() instead based on the
SPI_NOR_OCTAL_DTR_READ flag instead.
- Set SNOR_HWCAPS_PP_8_8_8_DTR in s28hs post_sfdp hook since this
capability is no longer set in Profile 1.0 parsing.
- Instead of just checking for spi_nor_get_protocol_width() in
spi_nor_octal_dtr_enable(), make sure the protocol is
SNOR_PROTO_8_8_8_DTR since get_protocol_width() only cares about data
width.
- Drop flag SPI_NOR_SOFT_RESET. Instead, discover soft reset capability
via BFPT.
- Do not make an invalid Quad Enable BFPT field a fatal error. Silently
ignore it by assuming no quad enable bit is present.
- Set dummy cycles for Cypress Semper flash to 24 instead of 20. This
allows for 200MHz operation in 8D mode compared to the 166MHz with 20.
- Rename spi_nor_cypress_octal_enable() to
spi_nor_cypress_octal_dtr_enable().
- Update spi-mtk-nor.c to reject DTR ops since it doesn't call
spi_mem_default_supports_op().
Changes in v4:
- Refactor the series to use the new spi-nor framework with the
manufacturer-specific bits separated from the core.
- Add support for Micron MT35XU512ABA.
- Use cmd.nbytes as the criteria of whether the data phase exists or not
instead of cmd.buf.in || cmd.buf.out in spi_nor_spimem_setup_op().
- Update Read FSR to use the same dummy cycles and address width as Read
SR.
- Fix BFPT parsing stopping too early for JESD216 rev B flashes.
- Use 2 byte reads for Read SR and FSR commands in DTR mode.
Changes in v3:
- Drop the DT properties "spi-rx-dtr" and "spi-tx-dtr". Instead, if
later a need is felt to disable DTR in case someone has a board with
Octal DTR capable flash but does not support DTR transactions for some
reason, a property like "spi-no-dtr" can be added.
- Remove mode bits SPI_RX_DTR and SPI_TX_DTR.
- Remove the Cadence Quadspi controller patch to un-block this series. I
will submit it as a separate patch.
- Rebase on latest 'master' and fix merge conflicts.
- Update read and write dirmap templates to use DTR.
- Rename 'is_dtr' to 'dtr'.
- Make 'dtr' a bitfield.
- Reject DTR ops in spi_mem_default_supports_op().
- Update atmel-quadspi to reject DTR ops. All other controller drivers
call spi_mem_default_supports_op() so they will automatically reject
DTR ops.
- Add support for both enabling and disabling DTR modes.
- Perform a Software Reset on flashes that support it when shutting
down.
- Disable Octal DTR mode on suspend, and re-enable it on resume.
- Drop enum 'spi_mem_cmd_ext' and make command opcode u16 instead.
Update spi-nor to use the 2-byte command instead of the command
extension. Since we still need a "extension type", mode that enum to
spi-nor and name it 'spi_nor_cmd_ext'.
- Default variable address width to 3 to fix SMPT parsing.
- Drop non-volatile change to uniform sector mode and rely on parsing
SMPT.
Changes in v2:
- Add DT properties "spi-rx-dtr" and "spi-tx-dtr" to allow expressing
DTR capabilities.
- Set the mode bits SPI_RX_DTR and SPI_TX_DTR when we discover the DT
properties "spi-rx-dtr" and spi-tx-dtr".
- spi_nor_cypress_octal_enable() was updating nor->params.read[] with
the intention of setting the correct number of dummy cycles. But this
function is called _after_ selecting the read so setting
nor->params.read[] will have no effect. So, update nor->read_dummy
directly.
- Fix spi_nor_spimem_check_readop() and spi_nor_spimem_check_pp()
passing nor->read_proto and nor->write_proto to
spi_nor_spimem_setup_op() instead of read->proto and pp->proto
respectively.
- Move the call to cqspi_setup_opcode_ext() inside cqspi_enable_dtr().
This avoids repeating the 'if (f_pdata->is_dtr)
cqspi_setup_opcode_ext()...` snippet multiple times.
- Call the default 'supports_op()' from cqspi_supports_mem_op(). This
makes sure the buswidth requirements are also enforced along with the
DTR requirements.
- Drop the 'is_dtr' argument from spi_check_dtr_req(). We only call it
when a phase is DTR so it is redundant.
Pratyush Yadav (17):
spi: spi-mem: allow specifying whether an op is DTR or not
spi: spi-mem: allow specifying a command's extension
spi: atmel-quadspi: reject DTR ops
spi: spi-mtk-nor: reject DTR ops
mtd: spi-nor: add support for DTR protocol
mtd: spi-nor: sfdp: get command opcode extension type from BFPT
mtd: spi-nor: sfdp: parse xSPI Profile 1.0 table
mtd: spi-nor: core: use dummy cycle and address width info from SFDP
mtd: spi-nor: core: do 2 byte reads for SR and FSR in DTR mode
mtd: spi-nor: core: enable octal DTR mode when possible
mtd: spi-nor: sfdp: do not make invalid quad enable fatal
mtd: spi-nor: sfdp: detect Soft Reset sequence support from BFPT
mtd: spi-nor: core: perform a Soft Reset on shutdown
mtd: spi-nor: core: disable Octal DTR mode on suspend.
mtd: spi-nor: core: expose spi_nor_default_setup() in core.h
mtd: spi-nor: spansion: add support for Cypress Semper flash
mtd: spi-nor: micron-st: allow using MT35XU512ABA in Octal DTR mode
drivers/mtd/spi-nor/core.c | 446 +++++++++++++++++++++++++++-----
drivers/mtd/spi-nor/core.h | 22 ++
drivers/mtd/spi-nor/micron-st.c | 103 +++++++-
drivers/mtd/spi-nor/sfdp.c | 131 +++++++++-
drivers/mtd/spi-nor/sfdp.h | 8 +
drivers/mtd/spi-nor/spansion.c | 166 ++++++++++++
drivers/spi/atmel-quadspi.c | 6 +
drivers/spi/spi-mem.c | 16 +-
drivers/spi/spi-mtk-nor.c | 10 +-
drivers/spi/spi-mxic.c | 3 +-
drivers/spi/spi-zynq-qspi.c | 11 +-
include/linux/mtd/spi-nor.h | 53 +++-
include/linux/spi/spi-mem.h | 14 +-
13 files changed, 889 insertions(+), 100 deletions(-)
--
2.27.0
base-commit: b3a9e3b962
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Double Transfer Rate (DTR) ops are added in spi-mem. But this controller
doesn't support DTR transactions. Since we don't use the default
supports_op(), which rejects all DTR ops, do that explicitly in our
supports_op().
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200623183030.26591-5-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Double Transfer Rate (DTR) ops are added in spi-mem. But this controller
doesn't support DTR transactions. Since we don't use the default
supports_op(), which rejects all DTR ops, do that explicitly in our
supports_op().
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200623183030.26591-4-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In xSPI mode, flashes expect 2-byte opcodes. The second byte is called
the "command extension". There can be 3 types of extensions in xSPI:
repeat, invert, and hex. When the extension type is "repeat", the same
opcode is sent twice. When it is "invert", the second byte is the
inverse of the opcode. When it is "hex" an additional opcode byte based
is sent with the command whose value can be anything.
So, make opcode a 16-bit value and add a 'nbytes', similar to how
multiple address widths are handled.
Some places use sizeof(op->cmd.opcode). Replace them with op->cmd.nbytes
The spi-mxic and spi-zynq-qspi drivers directly use op->cmd.opcode as a
buffer. Now that opcode is a 2-byte field, this can result in different
behaviour depending on if the machine is little endian or big endian.
Extract the opcode in a local 1-byte variable and use that as the buffer
instead. Both these drivers would reject multi-byte opcodes in their
supports_op() hook anyway, so we only need to worry about single-byte
opcodes for now.
The above two changes are put in this commit to keep the series
bisectable.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200623183030.26591-3-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Each phase is given a separate 'dtr' field so mixed protocols like
4S-4D-4D can be supported.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200623183030.26591-2-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There's a bunch of overhead in spi-geni-qcom's prepare_message. Get
rid of it. Before this change spi_geni_prepare_message() took around
14.5 us. After this change, spi_geni_prepare_message() takes about
1.75 us (as measured by ftrace).
What's here:
* We're always in FIFO mode, so no need to call it for every transfer.
This avoids a whole ton of readl/writel calls.
* We don't need to write a whole pile of config registers if the mode
isn't changing. Cache the last mode and only do the work if needed.
* For several registers we were trying to do read/modify/write, but
there was no reason. The registers only have one thing in them, so
just write them.
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200701174506.3.I2b3d7aeb1ea622335482cce60c58d2f8381e61dd@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In the patch ("spi: spi-geni-qcom: Avoid clock setting if not needed")
we avoid a whole pile of clock code. As part of that, we should have
restored the clock at runtime resume. Do that.
It turns out that, at least with today's configurations, this doesn't
actually matter. That's because none of the current device trees have
an OPP table for geni SPI yet. That makes dev_pm_opp_set_rate(dev, 0)
a no-op. This is why it wasn't noticed in the testing of the original
patch. It's still a good idea to fix, though.
Reviewed-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20200709074037.v2.1.I0b701fc23eca911a5bde4ae4fa7f97543d7f960e@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Every SPI transfer could have a different clock rate. The
spi-geni-qcom controller code to deal with this was never very well
optimized and has always had a lot of code plus some calls into the
clk framework which, at the very least, would grab a mutex. However,
until recently, the overhead wasn't _too_ much. That changed with
commit 0e3b8a81f5 ("spi: spi-geni-qcom: Add interconnect support")
we're now calling geni_icc_set_bw(), which leads to a bunch of math
plus:
geni_icc_set_bw()
icc_set_bw()
apply_constraints()
qcom_icc_set()
qcom_icc_bcm_voter_commit()
rpmh_invalidate()
rpmh_write_batch()
...and those rpmh commands can be a bit beefy if you call them too
often.
We already know what speed we were running at before, so if we see
that nothing has changed let's avoid the whole pile of code.
On my hardware, this made spi_geni_prepare_message() drop down from
~145 us down to ~14 us.
NOTE: Potentially it might also make sense to add some code into the
interconnect framework to avoid executing so much code when bandwidth
isn't changing, but even if we did that we still want to short circuit
here to save the extra math / clock calls.
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Akash Asthana<akashast@codeaurora.org>
Fixes: 0e3b8a81f5 ("spi: spi-geni-qcom: Add interconnect support")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200701174506.1.Icfdcee14649fc0a6c38e87477b28523d4e60bab3@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In commit cff80645d6 ("spi: spi-qcom-qspi: Add interconnect support")
the spi_geni_runtime_suspend() and spi_geni_runtime_resume()
became a bit slower. Measuring on my hardware I see numbers in the
hundreds of microseconds now.
Let's use autosuspend to help avoid some of the overhead. Now if
we're doing a bunch of transfers we won't need to be constantly
chruning.
The number 250 ms for the autosuspend delay was picked a bit
arbitrarily, so if someone has measurements showing a better value we
could easily change this.
Fixes: cff80645d6 ("spi: spi-qcom-qspi: Add interconnect support")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Rajendra Nayak <rnayak@codeaurora.org>
Tested-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Mukesh Kumar Savaliya <msavaliy@codeaurora.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Link: https://lore.kernel.org/r/20200709075113.v2.2.I3c56d655737c89bd9b766567a04b0854db1a4152@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
As per recent changes to the spi-qcom-qspi, now when we set the clock
we'll call into the interconnect framework and also call the OPP API.
Those are expensive operations. Let's avoid calling them if possible.
This has a big impact on getting transfer rates back up to where they
were (or maybe slightly better) before those patches landed.
Fixes: cff80645d6 ("spi: spi-qcom-qspi: Add interconnect support")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Rajendra Nayak <rnayak@codeaurora.org>
Tested-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Mukesh Kumar Savaliya <msavaliy@codeaurora.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Link: https://lore.kernel.org/r/20200709075113.v2.1.Ia7cb4f41ce93d37d0a764b47c8a453ce9e9c70ef@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
QSPI needs to vote on a performance state of a power domain depending on
the clock rate. Add support for it by specifying the perf state/clock rate
as an OPP table in device tree.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Mark Brown <broonie@kernel.org>
Cc: Alok Chauhan <alokc@codeaurora.org>
Cc: Akash Asthana <akashast@codeaurora.org>
Cc: linux-spi@vger.kernel.org
Link: https://lore.kernel.org/r/1593769293-6354-2-git-send-email-rnayak@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This converts the two Freescale i.MX SPI drivers
Freescale i.MX (CONFIG_SPI_IMX) and Freescale i.MX LPSPI
(CONFIG_SPI_FSL_LPSPI) to use GPIO descriptors handled in
the SPI core for GPIO chip selects whether defined in
the device tree or a board file.
The reason why both are converted at the same time is
that they were both using the same platform data and
platform device population helpers when using
board files intertwining the code so this gives a cleaner
cut.
The platform device creation was passing a platform data
container from each boardfile down to the driver using
struct spi_imx_master from <linux/platform_data/spi-imx.h>,
but this was only conveying the number of chipselects and
an int * array of the chipselect GPIO numbers.
The imx27 and imx31 platforms had code passing the
now-unused platform data when creating the platform devices,
this has been repurposed to pass around GPIO descriptor
tables. The platform data struct that was just passing an
array of integers and number of chip selects for the GPIO
lines has been removed.
The number of chipselects used to be passed from the board
file, because this number also limits the number of native
chipselects that the platform can use. To deal with this we
just augment the i.MX (CONFIG_SPI_IMX) driver to support 3
chipselects if the platform does not define "num-cs" as a
device property (such as from the device tree). This covers
all the legacy boards as these use <= 3 native chip selects
(or GPIO lines, and in that case the number of chip selects
is determined by the core from the number of available
GPIO lines). Any new boards should use device tree, so
this is a reasonable simplification to cover all old
boards.
The LPSPI driver never assigned the number of chipselects
and thus always fall back to the core default of 1 chip
select if no GPIOs are defined in the device tree.
The Freescale i.MX driver was already partly utilizing
the SPI core to obtain the GPIO numbers from the device tree,
so this completes the transtion to let the core handle all
of it.
All board files and the core i.MX boardfile registration
code is augmented to account for these changes.
This has been compile-tested with the imx_v4_v5_defconfig
and the imx_v6_v7_defconfig.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Robin Gong <yibin.gong@nxp.com>
Cc: Trent Piepho <tpiepho@impinj.com>
Cc: Clark Wang <xiaoning.wang@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Link: https://lore.kernel.org/r/20200625200252.207614-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200708194400.22213-1-grandmaster@al2klimov.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The error exit label out_free is no longer being used, it is redundant
and can be removed.
Cleans up warning:
drivers/spi/spi-atmel.c:1680:1: warning: label ‘out_free’ defined but not used [-Wunused-label]
Fixes: 2d9a744685 ("spi: atmel: No need to call spi_master_put() if spi_alloc_master() failed")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200709101203.1374117-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use kthread_create_worker() helper to simplify the code. It uses
the kthread worker API the right way. It will eventually allow
to remove the FIXME in kthread_worker_fn() and add more consistency
checks in the future.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20200709065007.26896-1-m.szyprowski@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This series tries to reduce a whole bunch of overhead in each SPI
transfer. Much of this overhead is new with the recent interconnect
changes, but even without those changes we still had some overhead
that we could avoid. Let's avoid all of it.
These changes are atop the Qualcomm tree to avoid merge conflicts. If
they look good, the most expedient way to land them is probably to get
Ack's from Mark and land then via the Qualcomm tree.
Most testing was done on the Chrome OS 5.4 tree, but sanity check was
done on mainline.
Douglas Anderson (3):
spi: spi-geni-qcom: Avoid clock setting if not needed
spi: spi-geni-qcom: Set an autosuspend delay of 250 ms
spi: spi-geni-qcom: Get rid of most overhead in prepare_message()
drivers/spi/spi-geni-qcom.c | 67 ++++++++++++++++++-------------------
1 file changed, 32 insertions(+), 35 deletions(-)
--
2.27.0.383.g050319c2ae-goog
Hello,
this series first fixes the calculation of the clock rate. The driver will
round up to the nearest clock rate instead of rounding down. Resulting in SPI
devices accessed with a too high SPI clock.
The remaining patches improve the performance of the driver. The changes range
from micro-optimizations like reducing MMIO writes to the controller to
reducing the number of needed interrupts in some use cases.
regards,
Marc
changes since v1:
- added Maxime Ripard's to the existing patches
- 06/10: (was 05/10 in v1)
"spi: spi-sun6i: sun6i_spi_drain_fifo(): introduce sun6i_spi_get_rx_fifo_count() and make use of it"
use FIELD_GET instead of open coding it
(tnx: Maxime Ripard)
- 05/10: "spi: spi-sun6i: sun6i_spi_get_tx_fifo_count: Convert manual shift+mask to FIELD_GET()"
new patch
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
In commit 0e3b8a81f5 ("spi: spi-geni-qcom: Add interconnect
support") the spi_geni_runtime_suspend() and spi_geni_runtime_resume()
became a bit slower. Measuring on my hardware I see numbers in the
hundreds of microseconds now.
Let's use autosuspend to help avoid some of the overhead. Now if
we're doing a bunch of transfers we won't need to be constantly
chruning.
The number 250 ms for the autosuspend delay was picked a bit
arbitrarily, so if someone has measurements showing a better value we
could easily change this.
Fixes: 0e3b8a81f5 ("spi: spi-geni-qcom: Add interconnect support")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Akash Asthana<akashast@codeaurora.org>
Link: https://lore.kernel.org/r/20200701174506.2.I9b8f6bb1e7e6d8847e2ed2cf854ec55678db427f@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
In sun6i_spi_transfer_one() the RX FIFO Ready (SUN6I_INT_CTL_RF_RDY) is
unconditionally enabled.
A RX interrupt is only needed, if more data than fits into the FIFO is going to
be received during this transfer. As the RX-FIFO is drained during transfer
complete interrupt, enable the RX FIFO Ready interrupt only if the data doesn't
fit into the FIFO.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20200706143443.9855-11-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
