Most boards use 25000000 as the default HZ, so rather than add a whole
bunch more boards, make it the default for everyone. This also fixes
randconfig builds as there was no default before.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The Blackfin arch has a bunch of custom section markings for its on-chip
regions, but they aren't declared in the right header.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Looks like the mutex-dec.h header file was incorrectly copied into the
Blackfin asm path. Nothing uses it, so punt it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This converts the irq handling in the Blackfin arch from the old irq.h /
system.h method to the new irqflags.h. A stepping stone on the way to
other tracing functionality.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Since U-Boot can support these compression types, add appropriate targets
to the Blackfin boot files.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The older smsc911x driver made platform data optional, but the newer one
always requires it, so add proper settings to the BF548-EZKIT.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The ADP5520 hooks up to PF7 rather than PG0.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The SPI flash on the BF518F-EZBRD board is actually hooked up to CS2,
not CS1, so make sure the resources are correct.
URL: http://blackfin.uclinux.org/gf/tracker/5220
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The Blackfin SPI driver can be driven by an IRQ now, so declare it in
the board resources.
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Before we configure the early UART, check to make sure we are running on
the expected processor - otherwise, we cause problems by configuring pins
that don't exist (and causing an infinite loop of faults).
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
When a low priority interrupt (like ethernet) is triggered between 2 high
priority IPI messages, a deadlock in disable_irq() is hit by the second
IPI handler. This is because the second IPI message is queued within the
first IPI handler, but the handler doesn't process all messages, and new
ones are inserted rather than appended. So now we process all the pending
messages, and append new ones to the pending list.
URL: http://blackfin.uclinux.org/gf/tracker/5226
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The IRQ functions take an "unsigned long" flags variable, not any other
type, so fix the places where we use "int" or "long".
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Rather than maintain a duplicate list of valid exceptions we can take in
the kernel both in the first if() check and the switch() check, delay the
oops check to after the switch(). All valid exceptions will have returned
by this point leaving only the invalid ones.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The trap_c() code pushes the hardware trace status onto the stack, but
doesn't always restore it when returning from some trap code paths. So
unify the exit code paths to all head to the end of the function.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The KGDB code uses this when switching processors to make sure the icache
is in a valid state.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Since the compiled-for cpu revision can be significant, include it in the
cpuinfo output along side the cpu revision we're currently running on.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We don't need to handle CPLB protection violations unless we are running
with the MPU on. Fix the entry code to call common trap_c, and remove the
code which is never run. This allows the traps test suite to run on older
boards with the MPU disabled.
URL: http://blackfin.uclinux.org/gf/tracker/5129
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6: (30 commits)
[S390] wire up sys_perf_counter_open
[S390] wire up sys_rt_tgsigqueueinfo
[S390] ftrace: add system call tracer support
[S390] ftrace: add function graph tracer support
[S390] ftrace: add function trace mcount test support
[S390] ftrace: add dynamic ftrace support
[S390] kprobes: use probe_kernel_write
[S390] maccess: arch specific probe_kernel_write() implementation
[S390] maccess: add weak attribute to probe_kernel_write
[S390] profile_tick called twice
[S390] dasd: forward internal errors to dasd_sleep_on caller
[S390] dasd: sync after async probe
[S390] dasd: check_characteristics cleanup
[S390] dasd: no High Performance FICON in 31-bit mode
[S390] dcssblk: revert devt conversion
[S390] qdio: fix access beyond ARRAY_SIZE of irq_ptr->{in,out}put_qs
[S390] vmalloc: add vmalloc kernel parameter support
[S390] uaccess: use might_fault() instead of might_sleep()
[S390] 3270: lock dependency fixes
[S390] 3270: do not register with tty_register_device
...
This will help kmemcheck (and possibly other debugging tools) since we
can now simply pass regs->bp to the stack tracer instead of specifying
the number of stack frames to skip, which is unreliable if gcc decides
to inline functions, etc.
Note that this makes the API incomplete for other architectures, but I
expect that those can be updated lazily, e.g. when they need it.
Cc: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
* 'perfcounters-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf_counter: Start documenting HAVE_PERF_COUNTERS requirements
perf_counter: Add forward/backward attribute ABI compatibility
perf record: Explicity program a default counter
perf_counter: Remove PERF_TYPE_RAW special casing
perf_counter: PERF_TYPE_HW_CACHE is a hardware counter too
powerpc, perf_counter: Fix performance counter event types
perf_counter/x86: Add a quirk for Atom processors
perf_counter tools: Remove one L1-data alias
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin: (62 commits)
Blackfin: fix sparseirq/kstat_irqs fallout
Blackfin: fix unused warnings after nommu update
Blackfin: export the last exception cause via debugfs
Blackfin: fix length checking in kgdb_ebin2mem
Blackfin: kgdb: fix up error return values
Blackfin: push access_ok() L1 attribute down
Blackfin: punt duplicated search_exception_table() prototype
Blackfin: add missing access_ok() checks to user functions
Blackfin: convert early_printk EVT init to a loop
Blackfin: document the lsl variants of the L1 allocator
Blackfin: rename Blackfin relocs according to the toolchain
Blackfin: check SIC defines rather than variant names
Blackfin: add SSYNC to set_dma_sg() for descriptor fetching
Blackfin: convert SMP to only use generic time framework
Blackfin: bf548-ezkit/bf537-stamp: add resources for ADXL345/346
Blackfin: override default uClinux MTD addr/size
Blackfin: fix command line corruption with DEBUG_DOUBLEFAULT
Blackfin: fix handling of initial L1 reservation
Blackfin: merge sram init functions
Blackfin: drop unused reserve_pda() function
...
This patch (as1241) renames a bunch of functions in the PM core.
Rather than go through a boring list of name changes, suffice it to
say that in the end we have a bunch of pairs of functions:
device_resume_noirq dpm_resume_noirq
device_resume dpm_resume
device_complete dpm_complete
device_suspend_noirq dpm_suspend_noirq
device_suspend dpm_suspend
device_prepare dpm_prepare
in which device_X does the X operation on a single device and dpm_X
invokes device_X for all devices in the dpm_list.
In addition, the old dpm_power_up and device_resume_noirq have been
combined into a single function (dpm_resume_noirq).
Lastly, dpm_suspend_start and dpm_resume_end are the renamed versions
of the former top-level device_suspend and device_resume routines.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Rename the functions performing "_noirq" dev_pm_ops
operations from device_power_down() and device_power_up()
to device_suspend_noirq() and device_resume_noirq().
The new function names are chosen to show that the functions
are responsible for calling the _noirq() versions to finalize
the suspend/resume operation. The current function names do
not perform power down/up anymore so the names may be misleading.
Global function renames:
- device_power_down() -> device_suspend_noirq()
- device_power_up() -> device_resume_noirq()
Static function renames:
- suspend_device_noirq() -> __device_suspend_noirq()
- resume_device_noirq() -> __device_resume_noirq()
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Len Brown <lenb@kernel.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch removes unused asm/suspend.h files for
the following architectures:
alpha, arm, ia64, m68k, mips, s390, um
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This is the last unification step. Here we do remove one of the files
and rename the left one as cpu.c, as both are now the same.
Also update power/Makefile, telling it to build cpu.o, instead of
cpu_(32|64).o
Signed-off-by: Sergio Luis <sergio@larces.uece.br>
Signed-off-by: Lauro Salmito <laurosalmito@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
In this step, we do unify the copyright notes for both files
cpu_32.c and cpu_64.c, making such files exactly the same.
It's the last step before the actual unification, that will
rename one of them to cpu.c and remove the other one.
Signed-off-by: Sergio Luis <sergio@larces.uece.br>
Signed-off-by: Lauro Salmito <laurosalmito@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
In this step we do unify cpu_32.c and cpu_64.c functions that
work on restoring the saved processor state. Also, we do
eliminate the forward declaration of fix_processor_context()
for X86_64, as it's not needed anymore.
Signed-off-by: Sergio Luis <sergio@larces.uece.br>
Signed-off-by: Lauro Salmito <laurosalmito@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
In this step we do unify cpu_32.c and cpu_64.c functions that
work on saving the processor state.
Signed-off-by: Sergio Luis <sergio@larces.uece.br>
Signed-off-by: Lauro Salmito <laurosalmito@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Aiming total unification of cpu_32.c and cpu_64.c, in this step
we do unify the global variables and existing forward declarations
for such files.
Signed-off-by: Sergio Luis <sergio@larces.uece.br>
Signed-off-by: Lauro Salmito <laurosalmito@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
First step towards the unification of cpu_32.c and cpu_64.c.
This commit unifies the headers of such files, making both
of them use the same header files. It also remove the uneeded
<module.h>.
Signed-off-by: Sergio Luis <sergio@larces.uece.br>
Signed-off-by: Lauro Salmito <laurosalmito@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
One of the numbers in arch/x86/kernel/acpi/sleep.c is long, but it is
not annotated appropriately, so sparese warns about it. Fix that.
[rjw: added the changelog.]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (290 commits)
ALSA: pcm - Update document about xrun_debug proc file
ALSA: lx6464es - support standard alsa module parameters
ALSA: snd_usb_caiaq: set mixername
ALSA: hda - add quirk for STAC92xx (SigmaTel STAC9205)
ALSA: use card device as parent for jack input-devices
ALSA: sound/ps3: Correct existing and add missing annotations
ALSA: sound/ps3: Restructure driver source
ALSA: sound/ps3: Fix checkpatch issues
ASoC: Fix lm4857 control
ALSA: ctxfi - Clear PCM resources at hw_params and hw_free
ALSA: ctxfi - Check the presence of SRC instance in PCM pointer callbacks
ALSA: ctxfi - Add missing start check in atc_pcm_playback_start()
ALSA: ctxfi - Add use_system_timer module option
ALSA: usb - Add boot quirk for C-Media 6206 USB Audio
ALSA: ctxfi - Fix wrong model id for UAA
ALSA: ctxfi - Clean up probe routines
ALSA: hda - Fix the previous tagra-8ch patch
ALSA: hda - Add 7.1 support for MSI GX620
ALSA: pcm - A helper function to compose PCM stream name for debug prints
ALSA: emu10k1 - Fix minimum periods for efx playback
...
* 'topic/slab/earlyboot-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
slab: setup cpu caches later on when interrupts are enabled
slab,slub: don't enable interrupts during early boot
slab: fix gfp flag in setup_cpu_cache()
x86: make zap_low_mapping could be used early
irq: slab alloc for default irq_affinity
memcg: fix page_cgroup fatal error in FLATMEM
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-lguest: (31 commits)
lguest: add support for indirect ring entries
lguest: suppress notifications in example Launcher
lguest: try to batch interrupts on network receive
lguest: avoid sending interrupts to Guest when no activity occurs.
lguest: implement deferred interrupts in example Launcher
lguest: remove obsolete LHREQ_BREAK call
lguest: have example Launcher service all devices in separate threads
lguest: use eventfds for device notification
eventfd: export eventfd_signal and eventfd_fget for lguest
lguest: allow any process to send interrupts
lguest: PAE fixes
lguest: PAE support
lguest: Add support for kvm_hypercall4()
lguest: replace hypercall name LHCALL_SET_PMD with LHCALL_SET_PGD
lguest: use native_set_* macros, which properly handle 64-bit entries when PAE is activated
lguest: map switcher with executable page table entries
lguest: fix writev returning short on console output
lguest: clean up length-used value in example launcher
lguest: Segment selectors are 16-bit long. Fix lg_cpu.ss1 definition.
lguest: beyond ARRAY_SIZE of cpu->arch.gdt
...
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-module-and-param:
module: cleanup FIXME comments about trimming exception table entries.
module: trim exception table on init free.
module: merge module_alloc() finally
uml module: fix uml build process due to this merge
x86 module: merge the rest functions with macros
x86 module: merge the same functions in module_32.c and module_64.c
uvesafb: improve parameter handling.
module_param: allow 'bool' module_params to be bool, not just int.
module_param: add __same_type convenience wrapper for __builtin_types_compatible_p
module_param: split perm field into flags and perm
module_param: invbool should take a 'bool', not an 'int'
cyber2000fb.c: use proper method for stopping unload if CONFIG_ARCH_SHARK
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Provide _sdata in the vmlinux.lds.S file
x86: handle initrd that extends into unusable memory
.ko is normally not included in Kconfig help, make it consistent.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This version requires that host and guest have the same PAE status.
NX cap is not offered to the guest, yet.
Signed-off-by: Matias Zabaljauregui <zabaljauregui@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Add support for kvm_hypercall4(); PAE wants it.
Signed-off-by: Matias Zabaljauregui <zabaljauregui at gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
replace LHCALL_SET_PMD with LHCALL_SET_PGD hypercall name
(That's really what it is, and the confusion gets worse with PAE support)
Signed-off-by: Matias Zabaljauregui <zabaljauregui@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Reported-by: Jeremy Fitzhardinge <jeremy@goop.org>
Some cleanups and replace direct assignment with native_set_* macros which properly handle 64-bit entries when PAE is activated
Signed-off-by: Matias Zabaljauregui <zabaljauregui@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The downside of the last patch which made restore_flags and irq_enable
check interrupts is that they are now too big to be patched directly
into the callsites, so the C versions are always used.
But the C versions go via PV_CALLEE_SAVE_REGS_THUNK which saves all
the registers. In fact, we don't need any registers in the fast path,
so we can do better than this if we actually code them in assembler.
The results are in the noise, but since it's about the same amount of
code, it's worth applying.
1GB Guest->Host: input(suppressed),output(suppressed)
Before:
Seconds: 0:16.53
Packets: 377268,753673
Interrupts: 22461,24297
Notifications: 1(5245),21303(732370)
Net IRQs triggered: 377023(245),42578(711095)
After:
Seconds: 0:16.48
Packets: 377289,753673
Interrupts: 22281,24465
Notifications: 1(5245),21296(732377)
Net IRQs triggered: 377060(229),42564(711109)
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
lguest never checked for pending interrupts when enabling interrupts, and
things still worked. However, it makes a significant difference to TCP
performance, so it's time we fixed it by introducing a pending_irq flag
and checking it on irq_restore and irq_enable.
These two routines are now too big to patch into the 8/10 bytes
patch space, so we drop that code.
Note: The high latency on interrupt delivery had a very curious
effect: once everything else was optimized, networking without GSO was
faster than networking with GSO, since more interrupts were sent and
hence a greater chance of one getting through to the Guest!
Note2: (Almost) Closing the same loophole for iret doesn't have any
measurable effect, so I'm leaving that patch for the moment.
Before:
1GB tcpblast Guest->Host: 30.7 seconds
1GB tcpblast Guest->Host (no GSO): 76.0 seconds
After:
1GB tcpblast Guest->Host: 6.8 seconds
1GB tcpblast Guest->Host (no GSO): 27.8 seconds
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Copy from arch/x86/kernel/irqinit_32.c: we don't use the vectors beyond
LGUEST_IRQS (if any), but we might as well set them all.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Sachin Sant reported these compiler errors:
CC arch/powerpc/kernel/power7-pmu.o
arch/powerpc/kernel/power7-pmu.c:297: error: PERF_COUNT_CPU_CYCLES undeclared here (not in a function)
Which happened because a last-minute rename of symbols crossed with
the Power7 support patch.
Fix this by using the new symbol names.
Reported-by: Sachin Sant <sachinp@in.ibm.com>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@ozlabs.org
LKML-Reference: <1244788494.5554.1.camel@ht.satnam>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Everyone cut and paste this comment from my original one. We now do
it generically, so cut the comments.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Amerigo Wang <amwang@redhat.com>
It's theoretically possible that there are exception table entries
which point into the (freed) init text of modules. These could cause
future problems if other modules get loaded into that memory and cause
an exception as we'd see the wrong fixup. The only case I know of is
kvm-intel.ko (when CONFIG_CC_OPTIMIZE_FOR_SIZE=n).
Amerigo fixed this long-standing FIXME in the x86 version, but this
patch is more general.
This implements trim_init_extable(); most archs are simple since they
use the standard lib/extable.c sort code. Alpha and IA64 use relative
addresses in their fixups, so thier trimming is a slight variation.
Sparc32 is unique; it doesn't seem to define ARCH_HAS_SORT_EXTABLE,
yet it defines its own sort_extable() which overrides the one in lib.
It doesn't sort, so we have to mark deleted entries instead of
actually trimming them.
Inspired-by: Amerigo Wang <amwang@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: linux-alpha@vger.kernel.org
Cc: sparclinux@vger.kernel.org
Cc: linux-ia64@vger.kernel.org
As Christoph Hellwig suggested, module_alloc() actually can be
unified for i386 and x86_64 (of course, also UML).
Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: 'Ingo Molnar' <mingo@elte.hu>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Due to the previous merge, uml needs to be fixed.
Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Merge the same functions both in module_32.c and module_64.c into
module.c.
This is the first step to merge both of them finally.
Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The fixed-function performance counters do not work on current Atom
processors. Use the general-purpose ones instead.
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <20090612080855.GA2286@ywang-moblin2.bj.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The sparseirq changes (d7e51e66) played poorly with the Blackfin irqchip
implementation as we're still using the old hardirq method. Our bad irq
structure had a NULL kstat_irqs field so when all the common code tries
to increment this field, everything goes big bada boom.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We have some test code that runs in userspace that exercises the exception
handling of the Blackfin pretty thoroughly. Part of the validation process
is checking the exact exception triggered, so export the last one seen to
userspace via debugfs when debugging is enabled for the test code to check.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The kgdb_ebin2mem() was decrementing the count variable to do parsing, but
then later still tries to use it based on its original meaning. So leave
it untouched and use a different variable to walk the memory.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The Blackfin kgdb code was all passing back positive errno values when it
really should have been using negative errno values.
Reported-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
There is no need for the L1 attribute to be on the prototype of the
access_ok() function as all consumers of the function do not care where it
lives -- they'll always use pcrel calls to get to it. This prevents
pointless recompiles of most of the system when this config option changes.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The common code already has a prototype for this function and we don't use
it anywhere in the Blackfin code, so punt it from the Blackfin headers.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The core string/clear user functions weren't checking the user pointers
which caused kernel crashes with some bad programs and tests (like LTP).
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The EVT registers are all contiguous in the memory map, so using a loop to
initialize them all rather than hardcoding the list results in much better
generated code (a hardware loop rather than a whole bunch of individual
loads).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Make sure the meaning of "lsl" is covered somewhere and it is clear why we
somewhat duplicate the sram alloc/free functions.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The latest Blackfin toolchain has fixed its relocation scheme to match
other ports: always use R_BFIN_ prefix and capitalize everything. This
brings the kernel in line with those fixes.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Rather than having to maintain a hard coded list of Blackfin variants, use
the SIC defines themselves. This fixes build problems on BF51x/BF538 under
some configurations as they were missing from one of the lists.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Make sure the internal core buffers are flushed before telling the DMA
engine to fetch the descriptor structure so that it gets the right values.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Due to a processor anomaly (05000263 to be exact), most Blackfin parts
cannot keep the embedded filesystem image directly after the kernel in
RAM. Instead, the filesystem needs to be relocated to the end of memory.
As such, we need to tweak the map addr/size during boot for Blackfin
systems.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Commit 6b3087c6 (which introduced Blackfin SMP) broke command line passing
when the DEBUG_DOUBLEFAULT config option was enabled. Switch the code to
using a scratch register and not R7 which holds the command line.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This restores some L1 reservation logic that was lost during the Blackfin
SMP merge.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Now that the sram_init() function exists only to call the bfin_sram_init()
after the punting of the reserve_pda() function, simply merge the two to
avoid pointless overhead.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The Per-processor Data Area isn't actually reserved by this function, and
all it ended up doing was issuing a printk(), so punt it.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
First we fix the prototypes for functions that return boolean values by
using "int" rather than "uint16_t". Then we introduce a get_gptimer_run()
function for checking the current run status of a timer, and then we add a
disable_gptimers_sync() function which parallels disable_gptimers() with
corresponding normal "_sync" behavior.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
People often copy & paste crash messages without surrounding context, so
include common useful information like system/processor stats in the crash
summary. This should smooth over the report/test cycle a bit more.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Returning too fast with a bad RETI can trigger false errors.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
When displaying a crash dump, make sure accessing the stack is safe so
we don't crash at the same time.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Hardware errors on the Blackfin architecture are queued by nature of the
hardware design. Things that could generate a hardware level queue up at
the system interface and might not process until much later, at which
point the system would send a notification back to the core.
As such, it is possible for user space code to do something that would
trigger a hardware error, but have it delay long enough for the process
context to switch. So when the hardware error does signal, we mistakenly
evaluate it as a different process or as kernel context and panic (erp!).
This makes it pretty difficult to find the offending context. But wait,
there is good news somewhere.
By forcing a SSYNC in the interrupt entry, we force all pending queues at
the system level to be processed and all hardware errors to be signaled.
Then we check the current interrupt state to see if the hardware error is
now signaled. If so, we re-queue the current interrupt and return thus
allowing the higher priority hardware error interrupt to process properly.
Since we haven't done any other context processing yet, the right context
will be selected and killed. There is still the possibility that the
exact offending instruction will be unknown, but at least we'll have a
much better idea of where to look.
The downside of course is that this causes system-wide syncs at every
interrupt point which results in significant performance degradation.
Since this situation should not occur in any properly configured system
(as hardware errors are triggered by things like bad pointers), make it a
debug configuration option and disable it by default.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
When possible, work around anomaly 05000220 (external memory is write
back cached, but L2 is not cached). If not possible, detect the
conditions at build time and reject any qualifying configurations.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Try to keep the naming conventions consistent, so:
SPI_ADC_BF533 -> BFIN_SPI_ADC
TWI_LCD -> BFIN_TWI_LCD
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This way we properly catch and kill applications that jump to a NULL ptr.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
For systems where the core cycles are not a usable tick source (like SMP
or cycles gets updated), enable gptimer0 as an alternative.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Add some notes for anomaly 05000120 to make sure we work around it.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The two high address lines on the BF51x are not dedicated which means we
need to handle them like any other peripheral pin if we want to access the
upper 2MB of parallel flash.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Detect and reject operating conditions for anomaly 05000274 since the
problem cannot be worked around in software.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Workaround anomaly 05000227 by only using the scratch pad for stack when
absolutely necessary. The core code which reprograms clocks really only
touches MMRs directly with constants.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Make sure we work around anomaly 05000287 by configuring different port
preferences for the data cache.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Add a reminder note to avoid the DMA_DONE bit in our DMA core code.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Our early L1 relocate code may implicitly call code which lives in L1
memory. This is due to the dma_memcpy() rewrite that made the DMA code
lockless and safe to be used by multiple processes. If we start the
early DMA memcpy to relocate things into L1 instruction but then our
DMA memcpy code calls a function that lives in L1, things fall apart.
As such, create a small dedicated DMA memcpy routine that we can assume
sanity at boot time.
Reported-by: Filip Van Rillaer <filip.vanrillaer@oneaccess-net.com>
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Add some defines to make the BF538/BF561 look like most other Blackfin
parts in that it has a MDMA0 channel available for low level init.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Make sure our bfin_addr_dcachable() function flags cached L2 SRAM properly
else memory easily goes unflushed when working with DMA.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Since 90% of this driver can be handled in user space, move it to the
corebld user space application.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Simplify the do_flush macro now that we don't need to take into account
a second instruction being used together.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Update the default revs based on what we actually support (bf54x-0.[01]
is too broken to use).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Some drivers expect to be able to request both as GPIO and GPIO IRQ, so
allow that use case.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Make sure the addresses declared match reality, and make the PATA IRQ code
optional.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
ipipe-2.6.28.9-blackfin-git95aafe6.patch
Singed-off-by: Philippe Gerum <rpm@xenomai.org>
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The I/O port functions take ints, so we need to cast them up before
passing to our read/write funcs to avoid ugly messes of warnings.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
The traps test case 21 "exception 0x3f: l1_instruction_access" would make
the kernel panic on BF533's because we end up calling show_stack()
infinitely.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Make sure we flush all data caches and their write buffers before flushing
icache, otherwise random edge cases could crop up where stale data is read
into icache from external memory. As fallout, punt the combined icache +
dcache flush function since we cannot safely do them back to back -- the
SSYNC is needed between the dcache flush and the icache flush.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Move exception stack mess from entry.S to init.c to fix link failure when
CONFIG_EXCEPTION_L1_SCRATCH is in use.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
By default, it is routed to async memory address. In GPIO case,
GPIO peripheral PINs should be requested in advance.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
System call tracer support for s390.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Function graph tracer support for s390.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add support for early test if the function tracer is enabled or
disabled. Saves some extra function calls.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use proble_kernel_write() to patch the kernel.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add an s390 specific probe_kernel_write() function which allows to
write to the kernel text segment even if write protection is enabled.
This is implemented using the lra (load real address) and stura (store
using real address) instructions.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
profile_tick is called twice for every clock comparator interrupt.
The generic clock event code does it in tick_sched_timer and the
s390 backend code in clock_comparator_work. That is one too many,
remove the one in the arch backend code.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
With the kernel parameter 'vmalloc=<size>' the size of the vmalloc area
can be specified. This can be used to increase or decrease the size of
the area. Works in the same way as on some other architectures.
This can be useful for features which make excessive use of vmalloc and
wouldn't work otherwise.
The default sizes remain unchanged: 96MB for 31 bit kernels and 1GB for
64 bit kernels.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Adds more checking in case lockdep is turned on.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Enable secure computing on s390 as well.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Implement is_compat_task and use it all over the place.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This adds a mini sclp device driver for very early use. The primary
and probably only use will be to emit a message to the console if the
cpu doesn't provide the minimum required capabilities to run the kernel.
After printing the message a disabled wait will be loaded and the
machine stops operating.
Printing the message is also part of this patch.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
All definition in cpu.h have to do with cputime accounting. Move
them to cputime.h and remove the header file.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The syntax of the vdso kernel parameter is documented as vdso=[on|off].
The implementation uses vdso=[0|1], an invalid parameter string disables
the vdso support. Fix the mismatch by adding vdso=[on|off] as additional
parameter syntax.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
_sdata is a common symbol defined by many architectures and made
available to the kernel via asm-generic/sections.h. Kmemleak uses this
symbol when scanning the data sections.
[ Impact: add new global symbol ]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
LKML-Reference: <20090511122105.26556.96593.stgit@pc1117.cambridge.arm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The patch that moved to vector.S and made common between 32 and 64-bit the
altivec code had a nasty bug on 32-bit (did I really test that ?) which
causes the kernel to blr back into userspace ... oops :-)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (87 commits)
nilfs2: get rid of bd_mount_sem use from nilfs
nilfs2: correct exclusion control in nilfs_remount function
nilfs2: simplify remaining sget() use
nilfs2: get rid of sget use for checking if current mount is present
nilfs2: get rid of sget use for acquiring nilfs object
nilfs2: remove meaningless EBUSY case from nilfs_get_sb function
remove the call to ->write_super in __sync_filesystem
nilfs2: call nilfs2_write_super from nilfs2_sync_fs
jffs2: call jffs2_write_super from jffs2_sync_fs
ufs: add ->sync_fs
sysv: add ->sync_fs
hfsplus: add ->sync_fs
hfs: add ->sync_fs
fat: add ->sync_fs
ext2: add ->sync_fs
exofs: add ->sync_fs
bfs: add ->sync_fs
affs: add ->sync_fs
sanitize ->fsync() for affs
repair bfs_write_inode(), switch bfs to simple_fsync()
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: remove unecessary include of thread_info.h in entry.S
m68knommu: enumerate INIT_THREAD fields properly
headers_check fix: m68k, swab.h
arch/m68knommu: Convert #ifdef DEBUG printk(KERN_DEBUG to pr_debug(
m68knommu: remove obsolete reset code
m68knommu: move CPU reset code for the 5272 ColdFire into its platform code
m68knommu: move CPU reset code for the 528x ColdFire into its platform code
m68knommu: move CPU reset code for the 527x ColdFire into its platform code
m68knommu: move CPU reset code for the 523x ColdFire into its platform code
m68knommu: move CPU reset code for the 520x ColdFire into its platform code
m68knommu: add CPU reset code for the 532x ColdFire
m68knommu: add CPU reset code for the 5249 ColdFire
m68knommu: add CPU reset code for the 5206e ColdFire
m68knommu: add CPU reset code for the 5206 ColdFire
m68knommu: add CPU reset code for the 5407 ColdFire
m68knommu: add CPU reset code for the 5307 ColdFire
m68knommu: merge system reset for code ColdFire 523x family
m68knommu: fix system reset for ColdFire 527x family
So we make sure MAXSMP gets a cleared cpumask
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On a system where system memory (according e820) is not covered by
mtrr, mtrr_trim_memory converts a portion of memory to reserved, but
bootloader has already put the initrd in that range.
Thus, we need to have 64bit to use relocate_initrd too.
[ Impact: fix using initrd when mtrr_trim_memory happen ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: stable@kernel.org
ep93xx: get_uart_rate() uses the constants EP93XX_SYSCON_CLOCK_CONTROL
and EP93XX_SYSCON_CLOCK_UARTBAUD, which no longer exist. Use
EP93XX_SYSCON_PWRCNT and EP93XX_SYSCON_PWRCNT_UARTBAUD instead
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'perfcounters-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (574 commits)
perf_counter: Turn off by default
perf_counter: Add counter->id to the throttle event
perf_counter: Better align code
perf_counter: Rename L2 to LL cache
perf_counter: Standardize event names
perf_counter: Rename enums
perf_counter tools: Clean up u64 usage
perf_counter: Rename perf_counter_limit sysctl
perf_counter: More paranoia settings
perf_counter: powerpc: Implement generalized cache events for POWER processors
perf_counters: powerpc: Add support for POWER7 processors
perf_counter: Accurate period data
perf_counter: Introduce struct for sample data
perf_counter tools: Normalize data using per sample period data
perf_counter: Annotate exit ctx recursion
perf_counter tools: Propagate signals properly
perf_counter tools: Small frequency related fixes
perf_counter: More aggressive frequency adjustment
perf_counter/x86: Fix the model number of Intel Core2 processors
perf_counter, x86: Correct some event and umask values for Intel processors
...
* 'topic/slab/earlyboot' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
vgacon: use slab allocator instead of the bootmem allocator
irq: use kcalloc() instead of the bootmem allocator
sched: use slab in cpupri_init()
sched: use alloc_cpumask_var() instead of alloc_bootmem_cpumask_var()
memcg: don't use bootmem allocator in setup code
irq/cpumask: make memoryless node zero happy
x86: remove some alloc_bootmem_cpumask_var calling
vt: use kzalloc() instead of the bootmem allocator
sched: use kzalloc() instead of the bootmem allocator
init: introduce mm_init()
vmalloc: use kzalloc() instead of alloc_bootmem()
slab: setup allocators earlier in the boot sequence
bootmem: fix slab fallback on numa
bootmem: use slab if bootmem is no longer available
Some generic code is using the horribly misnamed PCI_DMA_BUS_IS_PHYS
from asm/pci.h. This makes sure that an architecture without PCI
support does not have to define this itself but can rely on the
asm-generic version.
Signed-off-by: Remis Lima Baima <remis.developer@googlemail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The current asm-generic/page.h only contains the get_order
function, and asm-generic/uaccess.h only implements
unaligned accesses. This renames the file to getorder.h
and uaccess-unaligned.h to make room for new page.h
and uaccess.h file that will be usable by all simple
(e.g. nommu) architectures.
Signed-off-by: Remis Lima Baima <remis.developer@googlemail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The existing asm-generic/atomic.h only defines the
atomic_long type. This renames it to atomic-long.h
so we have a place to add a truly generic atomic.h
that can be used on all non-SMP systems.
Signed-off-by: Remis Lima Baima <remis.developer@googlemail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
This provides a reliable way for asm-generic/types.h and other
files to find out if it is running on a 32 or 64 bit platform.
We cannot use CONFIG_64BIT for this in headers that are included
from user space because CONFIG symbols are not available there.
We also cannot do it inside of asm/types.h because some headers
need the word size but cannot include types.h.
The solution is to introduce a new header <asm/bitsperlong.h>
that defines both __BITS_PER_LONG for user space and
BITS_PER_LONG for usage in the kernel. The asm-generic
version falls back to 32 bit unless the architecture overrides
it, which I did for all 64 bit platforms.
Signed-off-by: Remis Lima Baima <remis.developer@googlemail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The existing asm-generic versions are incomplete and included
by some architectures. New architectures should be able
to use a generic version, so rename the existing files and
change all users, which lets us add the new files.
Signed-off-by: Remis Lima Baima <remis.developer@googlemail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* 'for-2.6.31' of git://git.kernel.dk/linux-2.6-block: (153 commits)
block: add request clone interface (v2)
floppy: fix hibernation
ramdisk: remove long-deprecated "ramdisk=" boot-time parameter
fs/bio.c: add missing __user annotation
block: prevent possible io_context->refcount overflow
Add serial number support for virtio_blk, V4a
block: Add missing bounce_pfn stacking and fix comments
Revert "block: Fix bounce limit setting in DM"
cciss: decode unit attention in SCSI error handling code
cciss: Remove no longer needed sendcmd reject processing code
cciss: change SCSI error handling routines to work with interrupts enabled.
cciss: separate error processing and command retrying code in sendcmd_withirq_core()
cciss: factor out fix target status processing code from sendcmd functions
cciss: simplify interface of sendcmd() and sendcmd_withirq()
cciss: factor out core of sendcmd_withirq() for use by SCSI error handling code
cciss: Use schedule_timeout_uninterruptible in SCSI error handling code
block: needs to set the residual length of a bidi request
Revert "block: implement blkdev_readpages"
block: Fix bounce limit setting in DM
Removed reference to non-existing file Documentation/PCI/PCI-DMA-mapping.txt
...
Manually fix conflicts with tracing updates in:
block/blk-sysfs.c
drivers/ide/ide-atapi.c
drivers/ide/ide-cd.c
drivers/ide/ide-floppy.c
drivers/ide/ide-tape.c
include/trace/events/block.h
kernel/trace/blktrace.c
* 'kvm-updates/2.6.31' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (138 commits)
KVM: Prevent overflow in largepages calculation
KVM: Disable large pages on misaligned memory slots
KVM: Add VT-x machine check support
KVM: VMX: Rename rmode.active to rmode.vm86_active
KVM: Move "exit due to NMI" handling into vmx_complete_interrupts()
KVM: Disable CR8 intercept if tpr patching is active
KVM: Do not migrate pending software interrupts.
KVM: inject NMI after IRET from a previous NMI, not before.
KVM: Always request IRQ/NMI window if an interrupt is pending
KVM: Do not re-execute INTn instruction.
KVM: skip_emulated_instruction() decode instruction if size is not known
KVM: Remove irq_pending bitmap
KVM: Do not allow interrupt injection from userspace if there is a pending event.
KVM: Unprotect a page if #PF happens during NMI injection.
KVM: s390: Verify memory in kvm run
KVM: s390: Sanity check on validity intercept
KVM: s390: Unlink vcpu on destroy - v2
KVM: s390: optimize float int lock: spin_lock_bh --> spin_lock
KVM: s390: use hrtimer for clock wakeup from idle - v2
KVM: s390: Fix memory slot versus run - v3
...
Don't hardcode to node zero for early boot IRQ setup memory allocations.
[ penberg@cs.helsinki.fi: minor cleanups ]
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Now that we set up the slab allocator earlier, we can get rid of some
alloc_bootmem_cpumask_var() calls in boot code.
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
* frv:
FRV: Implement new-style ptrace
FRV: Don't turn on TIF_SYSCALL_TRACE unconditionally in syscall prologue
FRV: Implement TIF_NOTIFY_RESUME
FRV: Remove in-kernel strace code
FRV: BUG to BUG_ON changes
FRV: bitops: Change the bitmap index from int to unsigned long
* mn10300:
MN10300: Add utrace/tracehooks support
MN10300: Don't set the dirty bit in the DTLB entries in the TLB-miss handler
Add utrace/tracehooks support to MN10300.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the special handling for the Data TLB entry dirty bit in the TLB-miss
handler. As the code stands, all that it does is to cause us to take a second
data address exception to set the dirty bit. Instead, we can just let
pte_mkdirty() set the bit.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement the new-style ptrace for FRV, including adding appropriate
tracehooks.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don't turn on TIF_SYSCALL_TRACE unconditionally in syscall prologue in FRV's
entry.S. This was originally for debugging stuff and should have been removed
a long time ago.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement the TIF_NOTIFY_RESUME thread flag, making it call do_notify_resume()
which then clears it. This will be made use of later by tracehooks in the
new-style ptrace implementation
Also discard TIF_IRET as that's not used by FRV.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove in-kernel strace code from the FRV arch as it's not really needed any
more.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change the index to unsigned long in all bitops for [frv]
Signed-off-by: Justin Chen <justin.chen@hp.com>
Reviewed-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* serial-from-alan: (79 commits)
moxa: prevent opening unavailable ports
imx: serial: use tty_encode_baud_rate to set true rate
imx: serial: add IrDA support to serial driver
imx: serial: use rational library function
lib: isolate rational fractions helper function
imx: serial: handle initialisation failure correctly
imx: serial: be sure to stop xmit upon shutdown
imx: serial: notify higher layers in case xmit IRQ was not called
imx: serial: fix one bit field type
imx: serial: fix whitespaces (no changes in functionality)
tty: use prepare/finish_wait
tty: remove sleep_on
sierra: driver interface blacklisting
sierra: driver urb handling improvements
tty: resolve some sierra breakage
timbuart: Fix the termios logic
serial: Added Timberdale UART driver
tty: Add URL for ttydev queue
devpts: unregister the file system on error
tty: Untangle termios and mm mutex dependencies
...
The top (fastest) and last level (biggest) caches are the most
interesting ones, performance wise.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
[ Fixed the Nehalem LL table to LLC Reference/Miss events ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Pure renames only, to PERF_COUNT_HW_* and PERF_COUNT_SW_*.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Using the iMX serial driver with an IrDA device
needs extra peripheral settings and specific
timing depending on the transmitter circuitry used.
Signed-off-by: Fabian Godehardt <fg@emlix.com>
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The legacy TCSETA{,W,F} ioctls failed to set the termio->c_line field
on x86. This adds a missing get_user.
The same ioctls also fail to report faulting user pointers, which
we keep ignoring.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For suspend/resume to work, spitz needs pxa_pm_suspend/resume to be
called. Otherwise PSPR is not set properly, and system will die during
resume.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This adds tables of event codes for the generalized cache events for
all the currently supported powerpc processors: POWER{4,5,5+,6,7} and
PPC970*, plus powerpc-specific code to use these tables when a
generalized cache event is requested.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <18992.36430.933526.742969@drongo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This adds the back-end for the PMU on POWER7 processors. POWER7
has 4 fully-programmable counters and two fixed-function counters
(which do respect the freeze conditions, can generate interrupts,
and are writable, unlike PMC5/6 on POWER5+/6).
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <18992.36329.189378.17992@drongo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit c9690998ef (x86: memtest: remove
64-bit division) introduced following compile warning:
arch/x86/mm/memtest.c: In function 'memtest':
arch/x86/mm/memtest.c:56: warning: comparison of distinct pointer types lacks a cast
arch/x86/mm/memtest.c:58: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Replace calls to pxa_gpio_mode with respective gpio_request() /
gpio_direction_input(). In principle these calls can be dropped as
the only use of those GPIO are IRQs and IRQ code does setup GPIO
correctly.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
As pxa now is the only user of sharpsl_pm we can drop several startup
functions into generic code thus dropping several global functions.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
collie_pm was the only non-PXA user of sharpsl_pm. Now as it's gone we
can merge code into one single file to allow further cleanup.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This file was never enabled in the mainline kernel, new ongoing work on
battery driver by Thomas Kunze makes it completely obsolete, so remove
it now.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Add default configure file for w90p910 platform.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add multi-function pin api for w90p910 platform.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch introduces three boot options (no_cmci, dont_log_ce
and ignore_ce) to control handling for corrected errors.
The "mce=no_cmci" boot option disables the CMCI feature.
Since CMCI is a new feature so having boot controls to disable
it will be a help if the hardware is misbehaving.
The "mce=dont_log_ce" boot option disables logging for corrected
errors. All reported corrected errors will be cleared silently.
This option will be useful if you never care about corrected
errors.
The "mce=ignore_ce" boot option disables features for corrected
errors, i.e. polling timer and cmci. All corrected events are
not cleared and kept in bank MSRs.
Usually this disablement is not recommended, however it will be
a help if there are some conflict with the BIOS or hardware
monitoring applications etc., that clears corrected events in
banks instead of OS.
[ And trivial cleanup (space -> tab) for doc is included. ]
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
LKML-Reference: <4A30ACDF.5030408@jp.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch:
- Adds print_mce_head() instead of first flag
- Makes the header to be printed always
- Stops double printing of corrected errors
[ This portion originates from Huang Ying's patch ]
Originally-From: Huang Ying <ying.huang@intel.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
LKML-Reference: <4A30AC83.5010708@jp.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Now that the dependent patches are merged, we are ready to enable
sparseirq support. This simply adds the Kconfig option, and then converts
from the _cpu to the _node allocation routines to follow the upstream
sparseirq API changes.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There was a typo here that had this as sys_writev() instead of
sys_pwritev(), fix this up. sh64 got this right, as did the preadv()
case.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes up a typo in the ll/sc based cmpxchg code which apparently
wasn't getting a lot of testing due to the swapped old/new pair. With
that fixed up, the ll/sc code also starts using it and provides its own
atomic_add_unless().
Signed-off-by: Aoi Shinkai <shinkoi2005@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch rewrites the sh7722 clock framework code.
The new code makes use of the recently merged div4,
div6 and mstp32 helper code. Both extal and dll are
supported as input clocks to the pll.
While at it, now when all SuperH Mobile processors
are converted, fix CONFIG_SH_CLK_CPG_LEGACY to depend
on CONFIG_ARCH_SHMOBILE.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch rewrites the sh7366 clock framework code.
The new code makes use of the recently merged div4,
div6 and mstp32 helper code. Both extal and dll are
supported as input clocks to the pll.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch rewrites the sh7343 clock framework code.
The new code makes use of the recently merged div4,
div6 and mstp32 helper code. Both extal and dll are
supported as input clocks to the pll.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch contains V3 of the sh7724 clock framework
rewrite. The new code makes use of the recently merged
div4, div6 and mstp32 helper code. Both extal and fll are
supported as input clocks to the pll. The div6 clocks are
fed through a divide-by-3 block.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch contains V2 of the sh7723 clock framework
rewrite. The new code makes use of the recently merged
div4, div6 and mstp32 helper code. Both extal and dll
are supported as input clocks to the pll.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the div6 clock helper code to add support
for enable(), disable() and set_rate() callbacks.
Needed by the camera clock enabling board code on Migo-R.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds mode pin configuration and
a machvec structure to Migo-R.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds sh7722 mode pin and pin function
controller comments.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds comments for the sh7724 mode pins
and pin function controller.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch is sh7723 mode pin V2. Mode pins and
pin function controller comments are added.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch reworks the mode pin code to keep the pin
definitions in one place. The mode pins values are now
the value of the bit instead of bit number.
With this patch in place the sh7785 header file contains
mode pin comments. The sh7785 clock code and the sh7785lcr
board code are updated to reflect the new shared mode pins.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds div6 clock helper code. The div6 clocks
are simply 6-bit divide-by-n modules where n is 1 to 64.
Needed for vclk on sh7722, sh7723, sh7343 and sh7366.
sh7724 needs this even more for vclk, fclka, fclkb,
irdaclk and spuclk.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes the per clock offset calculation in
sh_clk_div4_register(). Without this patch the offset
to the frequency table for each clock is incorrect.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use proper field value setting init INIT_THREAD macro.
Fixes this:
arch/m68knommu/kernel/init_task.c:27: warning: excess elements in array initializer
arch/m68knommu/kernel/init_task.c:27: warning: (near initialization for ‘init_task.thread.fpstate’)
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
fix the following 'make headers_check' warnings:
usr/include/asm-m68k/swab.h:4: include of <linux/types.h> is preferred over <asm/types.h>
usr/include/asm-m68k/swab.h:10: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
All ColdFire and non-MMU 68k code has custom reset routines.
Remove the obsolete and now un-used reset macros.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The sofwtare reset control code for the 523x ColdFire family uses the
same Reset unit hardware as the 527x and 528x ColdFire parts. So they
should all use the same code. Merge them.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The sofwtare reset control for the 527x ColdFire family is based on
the same Reset Control Unit as the 528x ColdFire family. So use the
same reset code for both.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
* 'tracing-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (244 commits)
Revert "x86, bts: reenable ptrace branch trace support"
tracing: do not translate event helper macros in print format
ftrace/documentation: fix typo in function grapher name
tracing/events: convert block trace points to TRACE_EVENT(), fix !CONFIG_BLOCK
tracing: add protection around module events unload
tracing: add trace_seq_vprint interface
tracing: fix the block trace points print size
tracing/events: convert block trace points to TRACE_EVENT()
ring-buffer: fix ret in rb_add_time_stamp
ring-buffer: pass in lockdep class key for reader_lock
tracing: add annotation to what type of stack trace is recorded
tracing: fix multiple use of __print_flags and __print_symbolic
tracing/events: fix output format of user stack
tracing/events: fix output format of kernel stack
tracing/trace_stack: fix the number of entries in the header
ring-buffer: discard timestamps that are at the start of the buffer
ring-buffer: try to discard unneeded timestamps
ring-buffer: fix bug in ring_buffer_discard_commit
ftrace: do not profile functions when disabled
tracing: make trace pipe recognize latency format flag
...
