This is no longer needed as we now just set the desired
.timer in MACHINE_START. We can now also remove timer-gp.h.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
This is needed for the following patches so we can initialize the
rest of the hardware timers later on.
As with the init_irq calls, there's no need to do cpu_is_omap calls
during the timer init as we only care about the major omap generation.
This means that we can initialize the sys_timer with the .timer
entries alone.
Note that for now we just set stubs for the various sys_timer entries
that will get populated in a later patch. The following patches will
also remove the omap_dm_timer_init calls and change the init for the
rest of the hardware timers to happen with an arch_initcall.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
to use REGULATOR_SUPPLY arrays.
CC: Mark Brown <broonie@opensource.wolfsonmicro.com>
CC: Mike Rapoport <mike@compulab.co.il>
CC: Nishant Kamat <nskamat@ti.com>
CC: Steve Sakoman <steve@sakoman.com>
CC: Felipe Balbi <balbi@ti.com>
CC: Santosh Shilimkar <santosh.shilimkar@ti.com>
CC: peter.barada@logicpd.com
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
eMMC does not handle power off when not in sleep state,
Skip regulator disable during probe when eMMC is
not in known state - state left by bootloader.
Resolves eMMC failure on OMAP4
mmc0: error -110 whilst initialising MMC card
Signed-off-by: Balaji T K <balajitk@ti.com>
Tested-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Acked-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP4 contains two separate instances of the padconf registers,
one in the core system config and one in the wakeup system config.
Pass in two tables to apply the correct values to each instance.
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The serial*_data should have been marked as __initdata as per
it's usage in the board files. Fix the same to remove the
section mismatch warnings caused by it.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Silesh C V <silesh@ti.com>
[tony@atomide.com: updated with additional fixes from Silesh]
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (33 commits)
OMAP3: PM: Boot message is not an error, and not helpful, remove it
OMAP3: cpuidle: change the power domains modes determination logic
OMAP3: cpuidle: code rework for improved readability
OMAP3: cpuidle: re-organize the C-states data
OMAP3: clean-up mach specific cpuidle data structures
OMAP3 cpuidle: remove useless SDP specific timings
usb: otg: OMAP4430: Powerdown the internal PHY when USB is disabled
usb: otg: OMAP4430: Fixing the omap4430_phy_init function
usb: musb: am35x: fix compile error when building am35x
usb: musb: OMAP4430: Power down the PHY during board init
omap: drop board-igep0030.c
omap: igep0020: add support for IGEP3
omap: igep0020: minor refactoring
omap: igep0020: name refactoring for future merge with IGEP3
omap: Remove support for omap2evm
arm: omap2plus: GPIO cleanup
omap: musb: introduce default board config
omap: move detection of NAND CS to common-board-devices
omap: use common initialization for PMIC i2c bus
omap: consolidate touch screen initialization among different boards
...
use gpio_request_<one|array>() instead of multiple gpiolib calls,
remove unneeded variables, etc.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move some of the configurable HDMI PLL parameters to dssdev.clock struct.
Cleanup the function hdmi_compute_pll() by using the parameters defined in the
board file and do some cosmetic modifications.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
arch/arm/plat-omap/include/plat/display.h is an include for the OMAP DSS
driver. A more logical place for it is in include/video.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Introduce omap_pmic_init that registers i2c bus and PMIC device on that
bus and add omap2/3/4 wrappers for common cases.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In Blaze and Panda, 32KHz clock - CLK32KG to WLAN is supplied
from Phoenix TWL6030.
Add CLK32KG platform data to blaze and omap4panda board file.
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (258 commits)
omap: zoom: host should not pull up wl1271's irq line
arm: plat-omap: iommu: fix request_mem_region() error path
OMAP2+: Common CPU DIE ID reading code reads wrong registers for OMAP4430
omap4: mux: Remove duplicate mux modes
omap: iovmm: don't check 'da' to set IOVMF_DA_FIXED flag
omap: iovmm: disallow mapping NULL address when IOVMF_DA_ANON is set
omap2+: mux: Fix compile when CONFIG_OMAP_MUX is not selected
omap4: board-omap4panda: Initialise the serial pads
omap3: board-3430sdp: Initialise the serial pads
omap4: board-4430sdp: Initialise the serial pads
omap2+: mux: Add macro for configuring static with omap_hwmod_mux_init
omap2+: mux: Remove the use of IDLE flag
omap2+: Add separate list for dynamic pads to mux
perf: add OMAP support for the new power events
OMAP4: Add IVA OPP enteries.
OMAP4: Update Voltage Rail Values for MPU, IVA and CORE
OMAP4: Enable 800 MHz and 1 GHz MPU-OPP
OMAP3+: OPP: Replace voltage values with Macros
OMAP3: wdtimer: Fix CORE idle transition
Watchdog: omap_wdt: add fine grain runtime-pm
...
Fix up various conflicts in
- arch/arm/mach-omap2/board-omap3evm.c
- arch/arm/mach-omap2/clock3xxx_data.c
- arch/arm/mach-omap2/usb-musb.c
- arch/arm/plat-omap/include/plat/usb.h
- drivers/usb/musb/musb_core.h
Adding board file structure for display which adds the display
structure with HDMI as the default driver when the display init
is called.
HDMI GPIO configurations are also done in this file.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Most revisions of the OMAP4 Blaze/SDP platform do not have
the EHCI signals routed by default. The pads are routed
for the alternate HSI functionality instead, and explicit
board modifications are needed to route the signals to
the USB PHY on the board.
Also, turning on the PHY connected to the EHCI port causes
a board reboot during bootup due to an unintended short
on the rails - this affects many initial revisions of the
board, and needs a minor board mod to fix (or as a
workaround, one should not attempt to power on the
USB PHY).
Given that these boards need explicit board mods to even
get EHCI working (separate from the accidental short above),
we should not attempt to enable EHCI by default.
So drop the EHCI support from the board files for the
Blaze/SDP platforms.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Keshava Munegowda <keshava_mgowda@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Modifying the device & driver name from "mmci-omap-hs" to
"omap_hsmmc".
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Acked-by: Benoit Cousson<b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The usbhs intialization is invoked by all omap3 and omap4
variant board files.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Create the ehci and ohci specific platform data structures.
The port enum values are made common for both ehci and ohci.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fixed regulators in twl6030 do not have set_voltage hook.
Regulator core returns -22 if set_voltage is NULL and apply_uV is set
while applying the constraint to set voltage resulting in failure during probe
of these regulators.
Do not set apply_uV for fixed regulators which don't have set_voltage.
machine_constraints_voltage: VANA: failed to apply 2100000uV constraint
twl_reg twl_reg.43: can't register VANA, -22
twl_reg: probe of twl_reg.43 failed with error -22
machine_constraints_voltage: VCXIO: failed to apply 1800000uV constraint
twl_reg twl_reg.44: can't register VCXIO, -22
twl_reg: probe of twl_reg.44 failed with error -22
machine_constraints_voltage: VDAC: failed to apply 1800000uV constraint
twl_reg twl_reg.45: can't register VDAC, -22
twl_reg: probe of twl_reg.45 failed with error -22
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Introduced the suspend/resume function for the OMAP4430 internal PHY.
This will be used by the twl6030-usb transceiver driver.
Moved the clock enable/disable function calls and power on/off of the PHY
code from power on/off functions to suspend/resume function.
Pass the suspend function through board data for OMAP4430sdp and OMAP4panda.
This will be used by the twl6030-usb transceiver driver.
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
-Add the platform changes for the keypad driver
-Register keyboard device with hwmod framework.
Signed-off-by: Syed Rafiuddin <rafiuddin.syed@ti.com>
Signed-off-by: Abraham Arce <x0066660@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Most revisions of the OMAP4 Blaze/SDP platform do not have
the EHCI signals routed by default. The pads are routed
for the alternate HSI functionality instead, and explicit
board modifications are needed to route the signals to
the USB PHY on the board.
Also, turning on the PHY connected to the EHCI port causes
a board reboot during bootup due to an unintended short
on the rails - this affects many initial revisions of the
board, and needs a minor board mod to fix (or as a
workaround, one should not attempt to power on the
USB PHY).
Given that these boards need explicit board mods to even
get EHCI working (separate from the accidental short above),
we should not attempt to enable EHCI by default.
So drop the EHCI support from the board files for the
Blaze/SDP platforms.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Keshava Munegowda <keshava_mgowda@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Move non-mapping and non-irq initialization code out of .map_io and
.init_irq respectively into the new init_early hook.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 6aa85a5ae6 (omap4: 4430sdp:
enable the ehci port on 4430SDP) added code to enable EHCI
support on 4430sdp board.
Looks like the ULPI pin does not seem to be muxed properly on ES1.0
SDP and this causes the system to reboot when the ULPI PHY is
enabled.
Fix this by muxing the pin, this is the same setting for
both ES1.0 and ES2.0. Also add checking for gpio_request.
Cc: Keshava Munegowda <keshava_mgowda@ti.com
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (144 commits)
USB: add support for Dream Cheeky DL100B Webmail Notifier (1d34:0004)
USB: serial: ftdi_sio: add support for TIOCSERGETLSR
USB: ehci-mxc: Setup portsc register prior to accessing OTG viewport
USB: atmel_usba_udc: fix freeing irq in usba_udc_remove()
usb: ehci-omap: fix tll channel enable mask
usb: ohci-omap3: fix trivial typo
USB: gadget: ci13xxx: don't assume that PAGE_SIZE is 4096
USB: gadget: ci13xxx: fix complete() callback for no_interrupt rq's
USB: gadget: update ci13xxx to work with g_ether
USB: gadgets: ci13xxx: fix probing of compiled-in gadget drivers
Revert "USB: musb: pm: don't rely fully on clock support"
Revert "USB: musb: blackfin: pm: make it work"
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
...
Manually fix up trivial conflicts in USB Kconfig changes in:
arch/arm/mach-omap2/Kconfig
arch/sh/Kconfig
drivers/usb/Kconfig
drivers/usb/host/ehci-hcd.c
and annoying chip clock data conflicts in:
arch/arm/mach-omap2/clock3xxx_data.c
arch/arm/mach-omap2/clock44xx_data.c
Split omap2_init_common_hw() into two functions. The first,
omap2_init_common_infrastructure(), initializes the hwmod code and
data, the OMAP PM code, and the clock code and data. The second,
omap2_init_common_devices(), handles any other early device
initialization that, for whatever reason, has not been or cannot be
moved to initcalls or early platform devices.
This patch is required for the hwmod postsetup patch, which allows
board files to change the state that hwmods should be placed into at
the conclusion of the hwmod _setup() function. For example, for a
board whose creators wish to ensure watchdog coverage across the
entire kernel boot process, code to change the watchdog's postsetup
state will be added in the board-*.c file between the
omap2_init_common_infrastructure() and omap2_init_common_devices() function
calls.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Register BH1780GLI Ambient light sensor, which is an I2C device
for 4430SDP board.
Signed-off-by: Hemanth V <hemanthv@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enabling the musb OTG mode for SDP and PANDA boards.
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Registering the twl6030-usb transceiver device as a child to twl6030 core.
Removed the NOP transceiver init call from board file.
Populated twl4030_usb_data platform data structure with the function
pointers for OMAP4430 internal PHY operation to be used by twl630-usb driver.
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Implement GPIO as a platform device.
GPIO APIs are used in machine_init functions. Hence it is
required to complete GPIO probe before board_init. Therefore
GPIO device register and driver register are implemented as
postcore_initcalls.
omap_gpio_init() does nothing now and this function would be
removed in the next patch as it's usage is spread across most
of the board files.
Inorder to convert GPIO as platform device, modifications are
required in clockxxxx_data.c file for OMAP1 so that device names
can be used to obtain clock instead of getting clocks by
name/NULL ptr.
Use runtime pm APIs (pm_runtime_put*/pm_runtime_get*) for enabling
or disabling the clocks, modify sysconfig settings and remove usage
of clock FW APIs.
Note 1: Converting GPIO driver to use runtime PM APIs is not done as a
separate patch because GPIO clock names are different for various OMAPs
and are different for some of the banks in the same CPU. This would need
usage of cpu_is checks and bank id checks while using clock FW APIs in
the gpio driver. Hence while making GPIO a platform driver framework,
PM runtime APIs are used directly.
Note 2: While implementing GPIO as a platform device, pm runtime APIs
are used as mentioned above and modification is not done in gpio's
prepare for idle/ resume after idle functions. This would be done
in the next patch series and GPIO driver would be made to use dev_pm_ops
instead of sysdev_class in that series only.
Due to the above, the GPIO driver implicitly relies on
CM_AUTOIDLE = 1 on its iclk for power management to work, since the
driver never disables its iclk.
This would be taken care in the next patch series (see Note 3 below).
Refer to
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg39112.html
for more details.
Note 3: only pm_runtime_get_sync is called in gpio's probe() and
pm_runtime_put* is never called. This is to make the implementation
similar to the existing GPIO code. Another patch series would be sent
to correct this.
In OMAP3 and OMAP4 gpio's debounce clocks are optional clocks. They
are enabled/ disabled whenever required using clock framework APIs
TODO:
1. Cleanup the GPIO driver. Use function pointers and register
offest pointers instead of using hardcoded values
2. Remove all cpu_is_ checks and OMAP specific macros
3. Remove usage of gpio_bank array so that only
instance specific information is used in driver code
4. Rename 'method'/ avoid it's usage
5. Fix the non-wakeup gpios handling for OMAP2430, OMAP3 & OMAP4
6. Modify gpio's prepare for idle/ resume after idle functions
to use runtime pm implentation.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Basak, Partha <p-basak2@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
[tony@atomide.com: updated for bank specific revision and updated boards]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP4 SDP has an SMSC3320 PHY hooked up to EHCI on Port1.
The PHY power is controlled by GPIO 157.
Turn on the PHY power, and register the controller at init.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Select the CBS package if SDP4430 is enabled during config.
Use the proper package (CBL or CBS) based on chip revision.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Anand Gadiyar <gadiyar@ti.com>
Select the CBL package if SDP4430 is enabled during config.
Initialize the mux framework during the board init.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Adding card detect callback function and card detect configuration
function for MMC1 Controller on OMAP4.
Card detect configuration function does initial configuration of the
MMC Control & PullUp-PullDown registers of Phoenix.
For MMC1 Controller, card detect interrupt source is
twl6030 which is non-gpio. The card detect call back function provides
card present/absent status by reading MMC Control register present
on twl6030.
Since OMAP4 doesn't use any GPIO line as used in OMAP3 for card detect,
the suspend/resume initialization which was done in omap_hsmmc_gpio_init
previously is moved to the probe thus making it generic for both OMAP3 &
OMAP4.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (163 commits)
omap: complete removal of machine_desc.io_pg_offst and .phys_io
omap: UART: fix wakeup registers for OMAP24xx UART2
omap: Fix spotty MMC voltages
ASoC: OMAP4: MCPDM: Remove unnecessary include of plat/control.h
serial: omap-serial: fix signess error
OMAP3: DMA: Errata i541: sDMA FIFO draining does not finish
omap: dma: Fix buffering disable bit setting for omap24xx
omap: serial: Fix the boot-up crash/reboot without CONFIG_PM
OMAP3: PM: fix scratchpad memory accesses for off-mode
omap4: pandaboard: enable the ehci port on pandaboard
omap4: pandaboard: Fix the init if CONFIG_MMC_OMAP_HS is not set
omap4: pandaboard: remove unused hsmmc definition
OMAP: McBSP: Remove null omap44xx ops comment
OMAP: McBSP: Swap CLKS source definition
OMAP: McBSP: Fix CLKR and FSR signal muxing
OMAP2+: clock: reduce the amount of standard debugging while disabling unused clocks
OMAP: control: move plat-omap/control.h to mach-omap2/control.h
OMAP: split plat-omap/common.c
OMAP: McBSP: implement functional clock switching via clock framework
OMAP: McBSP: implement McBSP CLKR and FSR signal muxing via mach-omap2/mcbsp.c
...
Fixed up trivial conflicts in arch/arm/mach-omap2/
{board-zoom-peripherals.c,devices.c} as per Tony
Since we're now using addruart to establish the debug mapping, we can
remove the io_pg_offst and phys_io members of struct machine_desc.
The various declarations were removed using the following script:
grep -rl MACHINE_START arch/arm | xargs \
sed -i '/MACHINE_START/,/MACHINE_END/ { /\.\(phys_io\|io_pg_offst\)/d }'
[ Initial patch was from Jeremy Kerr, example script from Russell King ]
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Eric Miao <eric.miao at canonical.com>
Only OMAP2+ platforms have the System Control Module (SCM) IP block.
In the past, we've kept the SCM header file in plat-omap. This has
led to abuse - device drivers including it; includes being added that
create implicit dependencies on OMAP2+ builds; etc.
In response, move the SCM headers into mach-omap2/.
As part of this, remove the direct SCM access from the OMAP UDC
driver. It was clearly broken. The UDC code needs an indepth review for
use on OMAP2+ chips.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Cory Maccarrone <darkstar6262@gmail.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
This patch fixes sparse warnings due non declarations of static functions.
arch/arm/mach-omap2/timer-gp.c:115:12: warning: symbol 'omap2_gp_clockevent_set_gptimer' was not declared. Should it be static?
arch/arm/mach-omap2/powerdomain.c:993:5: warning: symbol 'pwrdm_set_lowpwrstchange' was not declared. Should it be static?
arch/arm/mach-omap2/board-flash.c:141:8: warning: symbol 'board_nand_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-n8x0.c:416:6: warning: symbol 'n8x0_mmc_slot1_cover_handler' was not declared. Should it be static?
arch/arm/mach-omap2/board-n8x0.c:544:13: warning: symbol 'n8x0_mmc_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-rx51-peripherals.c:902:13: warning: symbol 'rx51_peripherals_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-rx51-video.c:107:13: warning: symbol 'rx51_video_mem_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-zoom-debugboard.c:155:12: warning: symbol 'zoom_debugboard_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-zoom-peripherals.c:280:13: warning: symbol 'zoom_peripherals_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-igep0020.c:110:13: warning: symbol 'igep2_flash_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-am3517evm.c:109:6: warning: symbol 'am3517_evm_ethernet_init' was not declared. Should it be static?
drivers/mtd/onenand/omap2.c:577:5: warning: symbol 'omap2_onenand_rephase' was not declared. Should it be static?
Signed-off-by: Manjunath Kondaiah G <manjugk@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On OMAP4, MMC2 controller has eMMC which draws power from VAUX regulator
on TWL. Though the eMMC supports dual voltage[1.8v/3v] as per ocr register,
its VCC is fixed at 3V for operation. With this once the mmc core selects
the minimum voltage[1.8] supported based on the ocr value read from OCR register,
eMMC will not get detected. Thus the platform data for MMC2 is updated with ocr
mask and same will be communicated to core which will set the regulator to
always operate at 3V when ever turned ON.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Avoid possible crash if CONFIG_MMC_OMAP_HS is not set
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
wires variable is renamed, extended and this single variable to be used to
pass the platform capabilities, e.g DDR mode. Also removed the hardcoded
value was using as bus-width.
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap 4430sdp board support for the proximity sensor via GPIO keys.
The proximity sensor is connected to GPIO and is registered as a
GPIO key.
- Making the default state of the sensor off at bootup
- The init is called before platform_add_devices
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The board file changes for the digital compass hmc5843.
The interface to the device is i2c.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds support for GPIO LEDs present on OMAP4
SDP and Blaze boards. This basically adds platform data
required by leds-gpio driver
Signed-off-by: Hemanth V <hemanthv@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adding board configuration for the tmp105
temperature sensor. The interface to the sensor
is I2C.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The MMC1 and MMC2 cards have seperate LDO supplies. Current code assumes
that they are powered by same LDO.
This patch fixes the same and has VAUX1 as supply to MMC2 card.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Tested-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adding support for MMC1 & MMC2 controllers of OMAP4430 SDP
to board file.
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds i2c1 peripherals data to
omap4430 sdp board file.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds the i2c board support for OMAP4430 SDP platform.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch moves OMAP4 soc specific code from 4430sdp board file.
The change is necessary so that newer board support can be added
with minimal changes. This will be also problematic for
multi-board, multi-omap builds.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch moves omap_smc1 function to a seperate omap44xx-smc.S file
and sets compile flags as -Wa,-march=armv7-a.
This fix was suggested by Tony Lindgren <tony@atomide.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[tony@atomide.com: otherwise multi-omap build with V6 and V7 breaks]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The musb support is enabled in omap3 platforms. For omap4 only board
support is available and the driver still isn't supported.
Because of this build with omap3_defconfig used for multi-omap
doesn't work on omap4430 sdp.
This patch avoids usb_musb_init() by adding a cpu check
in the board file.
Thanks to Anand Gadiyar and Mankad Maulik for the suggestion
of patching board file instead of musb driver.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds support for Mentor USB to 4430 SDP board
file.
It also defines the base address for HS USB OTG controller
in OMAP4.
Also updates platform specfic structure with base address
and IRQ details.
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds L2 Cache support for OMAP4. External L2 cache
is used in OMAP4
CC: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
sdp4430_uart_config isn't used anywhere, so remove it.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch enables omap_serial_early_init() function for OMAP4430
SDP. Without this the bootup would throw oops in omap_serial_init().
Note that the ifndef CONFIG_ARCH_OMAP4 is split into two sections
to enable omap_serial_early_init(). This ifndef cannot be removed
until omap4 clock framework is implemented.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-By: Tony Lindgren <tony@atomide.com>
Reviewed-By: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move the remaining headers under plat-omap/include/mach
to plat-omap/include/plat. Also search and replace the
files using these headers to include using the right path.
This was done with:
#!/bin/bash
mach_dir_old="arch/arm/plat-omap/include/mach"
plat_dir_new="arch/arm/plat-omap/include/plat"
headers=$(cd $mach_dir_old && ls *.h)
omap_dirs="arch/arm/*omap*/ \
drivers/video/omap \
sound/soc/omap"
other_files="drivers/leds/leds-ams-delta.c \
drivers/mfd/menelaus.c \
drivers/mfd/twl4030-core.c \
drivers/mtd/nand/ams-delta.c"
for header in $headers; do
old="#include <mach\/$header"
new="#include <plat\/$header"
for dir in $omap_dirs; do
find $dir -type f -name \*.[chS] | \
xargs sed -i "s/$old/$new/"
done
find drivers/ -type f -name \*omap*.[chS] | \
xargs sed -i "s/$old/$new/"
for file in $other_files; do
sed -i "s/$old/$new/" $file
done
done
for header in $(ls $mach_dir_old/*.h); do
git mv $header $plat_dir_new/
done
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the low level debug UART io address as per this series.
The change is essential to have CONFIG_DEBUG_LL working.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP tags are deprecrated so drop them.
Drop UART config data which decides which UARTs to enable during boot.
This is no longer necessary since serial core code disables clocks
after inactivity.
Background: with new UART idle code, all on-chip UARTs are idled using
a configurable inactivity timer (default 5 seconds.) After the
inactivity timer, UART clocks are disabled automatically.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Search and replace OMAP_IO_ADDRESS with OMAP1_IO_ADDRESS and OMAP2_IO_ADDRESS,
and convert omap_read/write into a functions instead of a macros.
Also rename OMAP_MPUIO_VBASE to OMAP1_MPUIO_VBASE.
In the long run, most code should use ioremap + __raw_read/write instead.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some OMAP3 boards (Beagle Cx, Overo, RX51, Pandora) have 2
SDRAM parts connected to the SDRC.
This patch adds the following:
- add a new argument of type omap_sdrc_params struct*
to omap2_init_common_hw and omap2_sdrc_init for the 2nd CS params
- adapted the OMAP boards files to the new prototype of
omap2_init_common_hw
- add the SDRC 2nd CS registers offsets defines
- adapt the sram sleep code to configure the SDRC for the 2nd CS
Note: If the 2nd param to omap2_init_common_hw is NULL, then the
parameters are not programmed into the SDRC CS1 registers
Tested on 3430 SDP and Beagleboard rev C2 and B5, with
suspend/resume and frequency changes (cpufreq).
Signed-off-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch updates the Makefile and Kconfig entries for OMAP4. The OMAP4430 SDP
board file supports only minimal set of drivers.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
