Pull ARM updates from Russell King:
- nommu updates from Afzal Mohammed cleaning up the vectors support
- allow DMA memory "mapping" for nommu Benjamin Gaignard
- fixing a correctness issue with R_ARM_PREL31 relocations in the
module linker
- add strlen() prototype for the decompressor
- support for DEBUG_VIRTUAL from Florian Fainelli
- adjusting memory bounds after memory reservations have been
registered
- unipher cache handling updates from Masahiro Yamada
- initrd and Thumb Kconfig cleanups
* 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: (23 commits)
ARM: mm: round the initrd reservation to page boundaries
ARM: mm: clean up initrd initialisation
ARM: mm: move initrd init code out of arm_memblock_init()
ARM: 8655/1: improve NOMMU definition of pgprot_*()
ARM: 8654/1: decompressor: add strlen prototype
ARM: 8652/1: cache-uniphier: clean up active way setup code
ARM: 8651/1: cache-uniphier: include <linux/errno.h> instead of <linux/types.h>
ARM: 8650/1: module: handle negative R_ARM_PREL31 addends correctly
ARM: 8649/2: nommu: remove Hivecs configuration is asm
ARM: 8648/2: nommu: display vectors base
ARM: 8647/2: nommu: dynamic exception base address setting
ARM: 8646/1: mmu: decouple VECTORS_BASE from Kconfig
ARM: 8644/1: Reduce "CPU: shutdown" message to debug level
ARM: 8641/1: treewide: Replace uses of virt_to_phys with __pa_symbol
ARM: 8640/1: Add support for CONFIG_DEBUG_VIRTUAL
ARM: 8639/1: Define KERNEL_START and KERNEL_END
ARM: 8638/1: mtd: lart: Rename partition defines to be prefixed with PART_
ARM: 8637/1: Adjust memory boundaries after reservations
ARM: 8636/1: Cleanup sanity_check_meminfo
ARM: add CPU_THUMB_CAPABLE to indicate possible Thumb support
...
Bart Van Assche noted that the ib DMA mapping code was significantly
similar enough to the core DMA mapping code that with a few changes
it was possible to remove the IB DMA mapping code entirely and
switch the RDMA stack to use the core DMA mapping code. This resulted
in a nice set of cleanups, but touched the entire tree. This branch
will be submitted separately to Linus at the end of the merge window
as per normal practice for tree wide changes like this.
-----BEGIN PGP SIGNATURE-----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=e0Si
-----END PGP SIGNATURE-----
Merge tag 'for-next-dma_ops' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma DMA mapping updates from Doug Ledford:
"Drop IB DMA mapping code and use core DMA code instead.
Bart Van Assche noted that the ib DMA mapping code was significantly
similar enough to the core DMA mapping code that with a few changes it
was possible to remove the IB DMA mapping code entirely and switch the
RDMA stack to use the core DMA mapping code.
This resulted in a nice set of cleanups, but touched the entire tree
and has been kept separate for that reason."
* tag 'for-next-dma_ops' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (37 commits)
IB/rxe, IB/rdmavt: Use dma_virt_ops instead of duplicating it
IB/core: Remove ib_device.dma_device
nvme-rdma: Switch from dma_device to dev.parent
RDS: net: Switch from dma_device to dev.parent
IB/srpt: Modify a debug statement
IB/srp: Switch from dma_device to dev.parent
IB/iser: Switch from dma_device to dev.parent
IB/IPoIB: Switch from dma_device to dev.parent
IB/rxe: Switch from dma_device to dev.parent
IB/vmw_pvrdma: Switch from dma_device to dev.parent
IB/usnic: Switch from dma_device to dev.parent
IB/qib: Switch from dma_device to dev.parent
IB/qedr: Switch from dma_device to dev.parent
IB/ocrdma: Switch from dma_device to dev.parent
IB/nes: Remove a superfluous assignment statement
IB/mthca: Switch from dma_device to dev.parent
IB/mlx5: Switch from dma_device to dev.parent
IB/mlx4: Switch from dma_device to dev.parent
IB/i40iw: Remove a superfluous assignment statement
IB/hns: Switch from dma_device to dev.parent
...
The callers of the DMA alloc functions already provide the proper
context GFP flags. Make sure to pass them through to the CMA allocator,
to make the CMA compaction context aware.
Link: http://lkml.kernel.org/r/20170127172328.18574-3-l.stach@pengutronix.de
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Radim Krcmar <rkrcmar@redhat.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Alexander Graf <agraf@suse.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The newly added DMA_ATTR_PRIVILEGED is useful for creating mappings that
are only accessible to privileged DMA engines. Adding it to the
arm dma-mapping.c so that the ARM32 DMA IOMMU mapper can make use of it.
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
commit ab6494f0c9 ("nommu: Add noMMU support to the DMA API") have
add CONFIG_MMU compilation flag but that prohibit to use dma_mmap_wc()
when the platform doesn't have MMU.
This patch call vm_iomap_memory() in noMMU case to test if addresses
are correct and set vma->vm_flags rather than all return an error.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fs_initcall is definitely too late to initialize DMA-debug hash tables,
because some drivers might get probed and use DMA mapping framework
already in core_initcall. Late initialization of DMA-debug results in
false warning about accessing memory, that was not allocated, like this
one:
------------[ cut here ]------------
WARNING: CPU: 5 PID: 1 at lib/dma-debug.c:1104 check_unmap+0xa1c/0xe50
exynos-sysmmu 10a60000.sysmmu: DMA-API: device driver tries to free DMA memory it has not allocated [device
address=0x000000006ebd0000] [size=16384 bytes]
Modules linked in:
CPU: 5 PID: 1 Comm: swapper/0 Not tainted 4.9.0-rc5-00028-g39dde3d-dirty #44
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[<c0119dd4>] (unwind_backtrace) from [<c01122bc>] (show_stack+0x20/0x24)
[<c01122bc>] (show_stack) from [<c062714c>] (dump_stack+0x84/0xa0)
[<c062714c>] (dump_stack) from [<c0132560>] (__warn+0x14c/0x180)
[<c0132560>] (__warn) from [<c01325dc>] (warn_slowpath_fmt+0x48/0x50)
[<c01325dc>] (warn_slowpath_fmt) from [<c06814f8>] (check_unmap+0xa1c/0xe50)
[<c06814f8>] (check_unmap) from [<c06819c4>] (debug_dma_unmap_page+0x98/0xc8)
[<c06819c4>] (debug_dma_unmap_page) from [<c076c3e8>] (exynos_iommu_domain_free+0x158/0x380)
[<c076c3e8>] (exynos_iommu_domain_free) from [<c0764a30>] (iommu_domain_free+0x34/0x60)
[<c0764a30>] (iommu_domain_free) from [<c011f168>] (release_iommu_mapping+0x30/0xb8)
[<c011f168>] (release_iommu_mapping) from [<c011f23c>] (arm_iommu_release_mapping+0x4c/0x50)
[<c011f23c>] (arm_iommu_release_mapping) from [<c0b061ac>] (s5p_mfc_probe+0x640/0x80c)
[<c0b061ac>] (s5p_mfc_probe) from [<c07e6750>] (platform_drv_probe+0x70/0x148)
[<c07e6750>] (platform_drv_probe) from [<c07e25c0>] (driver_probe_device+0x12c/0x6b0)
[<c07e25c0>] (driver_probe_device) from [<c07e2c6c>] (__driver_attach+0x128/0x17c)
[<c07e2c6c>] (__driver_attach) from [<c07df74c>] (bus_for_each_dev+0x88/0xc8)
[<c07df74c>] (bus_for_each_dev) from [<c07e1b6c>] (driver_attach+0x34/0x58)
[<c07e1b6c>] (driver_attach) from [<c07e1350>] (bus_add_driver+0x18c/0x32c)
[<c07e1350>] (bus_add_driver) from [<c07e4198>] (driver_register+0x98/0x148)
[<c07e4198>] (driver_register) from [<c07e5cb0>] (__platform_driver_register+0x58/0x74)
[<c07e5cb0>] (__platform_driver_register) from [<c174cb30>] (s5p_mfc_driver_init+0x1c/0x20)
[<c174cb30>] (s5p_mfc_driver_init) from [<c0102690>] (do_one_initcall+0x64/0x258)
[<c0102690>] (do_one_initcall) from [<c17014c0>] (kernel_init_freeable+0x3d0/0x4d0)
[<c17014c0>] (kernel_init_freeable) from [<c116eeb4>] (kernel_init+0x18/0x134)
[<c116eeb4>] (kernel_init) from [<c010bbd8>] (ret_from_fork+0x14/0x3c)
---[ end trace dc54c54bd3581296 ]---
This patch moves initialization of DMA-debug to core_initcall. This is
safe from the initialization perspective. dma_debug_do_init() internally calls
debugfs functions and debugfs also gets initialised at core_initcall(), and
that is earlier than arch code in the link order, so it will get initialized
just before the DMA-debug.
Reported-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is bit large pile of code which bring in some nice additions:
- Error reporting: we have added a new mechanism for users of dmaenegine to
register a callback_result which tells them the result of the dma
transaction. Right now only one user ntb is using it.
- As we discussed on KS mailing list and pointed out NO_IRQ has no place in
kernel, this also remove NO_IRQ from dmaengine subsystem (both arm and
ppc users)
- Support for IOMMU slave transfers and it implementation for arm.
- To get better build coverage, enable COMPILE_TEST for bunch of driver,
and fix the warning and sparse complaints on these.
- Apart from above, usual updates spread across drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9iA3
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.9-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This is bit large pile of code which bring in some nice additions:
- Error reporting: we have added a new mechanism for users of
dmaenegine to register a callback_result which tells them the
result of the dma transaction. Right now only one user (ntb) is
using it.
- As we discussed on KS mailing list and pointed out NO_IRQ has no
place in kernel, this also remove NO_IRQ from dmaengine subsystem
(both arm and ppc users)
- Support for IOMMU slave transfers and its implementation for arm.
- To get better build coverage, enable COMPILE_TEST for bunch of
driver, and fix the warning and sparse complaints on these.
- Apart from above, usual updates spread across drivers"
* tag 'dmaengine-4.9-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (169 commits)
async_pq_val: fix DMA memory leak
dmaengine: virt-dma: move function declarations
dmaengine: omap-dma: Enable burst and data pack for SG
DT: dmaengine: rcar-dmac: document R8A7743/5 support
dmaengine: fsldma: Unmap region obtained by of_iomap
dmaengine: jz4780: fix resource leaks on error exit return
dma-debug: fix ia64 build, use PHYS_PFN
dmaengine: coh901318: fix integer overflow when shifting more than 32 places
dmaengine: edma: avoid uninitialized variable use
dma-mapping: fix m32r build warning
dma-mapping: fix ia64 build, use PHYS_PFN
dmaengine: ti-dma-crossbar: enable COMPILE_TEST
dmaengine: omap-dma: enable COMPILE_TEST
dmaengine: edma: enable COMPILE_TEST
dmaengine: ti-dma-crossbar: Fix of_device_id data parameter usage
dmaengine: ti-dma-crossbar: Correct type for of_find_property() third parameter
dmaengine/ARM: omap-dma: Fix the DMAengine compile test on non OMAP configs
dmaengine: edma: Rename set_bits and remove unused clear_bits helper
dmaengine: edma: Use correct type for of_find_property() third parameter
dmaengine: edma: Fix of_device_id data parameter usage (legacy vs TPCC)
...
Add methods to map/unmap device resources addresses for dma_map_ops that
are IOMMU aware. This is needed to map a device MMIO register from a
physical address.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
According to Documentation/printk-formats.txt when printing
a size_t variable we should use %zu or %zx format specifiers.
As we are printing a memory size value, we should better use %zu
in this case.
Reported-by: Frank Mori Hess <fmh6jj@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The dma-mapping core and the implementations do not change the DMA
attributes passed by pointer. Thus the pointer can point to const data.
However the attributes do not have to be a bitfield. Instead unsigned
long will do fine:
1. This is just simpler. Both in terms of reading the code and setting
attributes. Instead of initializing local attributes on the stack
and passing pointer to it to dma_set_attr(), just set the bits.
2. It brings safeness and checking for const correctness because the
attributes are passed by value.
Semantic patches for this change (at least most of them):
virtual patch
virtual context
@r@
identifier f, attrs;
@@
f(...,
- struct dma_attrs *attrs
+ unsigned long attrs
, ...)
{
...
}
@@
identifier r.f;
@@
f(...,
- NULL
+ 0
)
and
// Options: --all-includes
virtual patch
virtual context
@r@
identifier f, attrs;
type t;
@@
t f(..., struct dma_attrs *attrs);
@@
identifier r.f;
@@
f(...,
- NULL
+ 0
)
Link: http://lkml.kernel.org/r/1468399300-5399-2-git-send-email-k.kozlowski@samsung.com
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Acked-by: Mark Salter <msalter@redhat.com> [c6x]
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com> [cris]
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> [drm]
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Joerg Roedel <jroedel@suse.de> [iommu]
Acked-by: Fabien Dessenne <fabien.dessenne@st.com> [bdisp]
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com> [vb2-core]
Acked-by: David Vrabel <david.vrabel@citrix.com> [xen]
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> [xen swiotlb]
Acked-by: Joerg Roedel <jroedel@suse.de> [iommu]
Acked-by: Richard Kuo <rkuo@codeaurora.org> [hexagon]
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Acked-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> [s390]
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no> [avr32]
Acked-by: Vineet Gupta <vgupta@synopsys.com> [arc]
Acked-by: Robin Murphy <robin.murphy@arm.com> [arm64 and dma-iommu]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When doing dma allocation with IOMMU the __iommu_alloc_atomic() was
used even when the system was coherent. However, this function
allocates from a non-cacheable pool, which is fine when the device is
not cache coherent but won't work as expected in the device is cache
coherent. Indeed, the CPU and device must access the memory using the
same cacheability attributes.
Moreover when the devices are coherent, the mmap call must not change
the pg_prot flags in the vma struct. The arm_coherent_iommu_mmap_attrs
has been updated in the same way that it was done for the arm_dma_mmap
in commit 55af8a9164 ("ARM: 8387/1: arm/mm/dma-mapping.c: Add
arm_coherent_dma_mmap").
Suggested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When a L2 cache controller is used in a system that provides hardware
coherency, the entire outer cache operations are useless, and can be
skipped. Moreover, on some systems, it is harmful as it causes
deadlocks between the Marvell coherency mechanism, the Marvell PCIe
controller and the Cortex-A9.
In the current kernel implementation, the outer cache flush range
operation is triggered by the dma_alloc function.
This operation can be take place during runtime and in some
circumstances may lead to the PCIe/PL310 deadlock on Armada 375/38x
SoCs.
This patch extends the __dma_clear_buffer() function to receive a
boolean argument related to the coherency of the system. The same
things is done for the calling functions.
Reported-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull ARM updates from Russell King:
"Changes included in this pull request:
- revert pxa2xx-flash back to using ioremap_cached() and switch
memremap() to use arch_memremap_wb()
- remove pci=firmware command line argument handling
- remove unnecessary arm_dma_set_mask() implementation, the generic
implementation will do for ARM
- removal of the ARM kallsyms "hack" to work around mode switching
veneers and vectors located below PAGE_OFFSET
- tidy up build system output a little
- add L2 cache power management DT bindings
- remove duplicated local_irq_disable() in reboot paths
- handle AMBA primecell devices better at registration time with PM
domains (needed for Samsung SoCs)
- ARM specific preparation to support Keystone II kexec"
* 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8567/1: cache-uniphier: activate ways for secondary CPUs
ARM: 8570/2: Documentation: devicetree: Add PL310 PM bindings
ARM: 8569/1: pl2x0: Add OF control of cache power management
ARM: 8568/1: reboot: remove duplicated local_irq_disable()
ARM: 8566/1: drivers: amba: properly handle devices with power domains
ARM: provide arm_has_idmap_alias() helper
ARM: kexec: remove 512MB restriction on kexec crashdump
ARM: provide improved virt_to_idmap() functionality
ARM: kexec: fix crashkernel= handling
ARM: 8557/1: specify install, zinstall, and uinstall as PHONY targets
ARM: 8562/1: suppress "include/generated/mach-types.h is up to date."
ARM: 8553/1: kallsyms: remove --page-offset command line option
ARM: 8552/1: kallsyms: remove special lower address limit for CONFIG_ARM
ARM: 8555/1: kallsyms: ignore ARM mode switching veneers
ARM: 8548/1: dma-mapping: remove arm_dma_set_mask()
ARM: 8554/1: kernel: pci: remove pci=firmware command line parameter handling
ARM: memremap: implement arch_memremap_wb()
memremap: add arch specific hook for MEMREMAP_WB mappings
mtd: pxa2xx-flash: switch back from memremap to ioremap_cached
ARM: reintroduce ioremap_cached() for creating cached I/O mappings
As a set of driver-provided callbacks and static data, there is no
compelling reason for struct iommu_ops to be mutable in core code, so
enforce const-ness throughout.
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Commit 19e6e5e539 ("ARM: 8547/1: dma-mapping: store buffer
information") allocates a structure meant for internal buffer management
with the GFP flags of the buffer itself. This can trigger the following
safeguard in the slab/slub allocator:
if (unlikely(flags & GFP_SLAB_BUG_MASK)) {
pr_emerg("gfp: %un", flags & GFP_SLAB_BUG_MASK);
BUG();
}
Fix this by filtering the flags that make the slab allocator unhappy.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arm_dma_set_mask() implements exactly the same behavior as the fallback
that dma_set_mask() takes if the set_dma_mask op is not set. Remove it
and use that fallback instead like what is already done for
dma_get_mask().
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Given a device which uses arm_coherent_dma_ops and on which
dev_get_cma_area(dev) returns non-NULL, the following usage of the DMA
API with gfp=0 results in memory corruption and a memory leak.
p = dma_alloc_coherent(dev, sz, &dma, 0);
if (p)
dma_free_coherent(dev, sz, p, dma);
The memory leak is because the alloc allocates using
__alloc_simple_buffer() but the free attempts
dma_release_from_contiguous() which does not do free anything since the
page is not in the CMA area.
The memory corruption is because the free calls __dma_remap() on a page
which is backed by only first level page tables. The
apply_to_page_range() + __dma_update_pte() loop ends up interpreting the
section mapping as an addresses to a second level page table and writing
the new PTE to memory which is not used by page tables.
We don't have access to the GFP flags used for allocation in the free
function. Fix this by adding allocator backends and using this
information in the free function so that we always use the correct
release routine.
Fixes: 21caf3a7 ("ARM: 8398/1: arm DMA: Fix allocation from CMA for coherent DMA")
Signed-off-by: Rabin Vincent <rabin.vincent@axis.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Keep a list of allocated DMA buffers so that we can store metadata in
alloc() which we later need in free().
Signed-off-by: Rabin Vincent <rabin.vincent@axis.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If we know that TLB efficiency will not be an issue when memory is
accessed then it's not terribly important to allocate big chunks of
memory. The whole point of allocating the big chunks was that it would
make TLB usage efficient.
As Marek Szyprowski indicated:
Please note that mapping memory with larger pages significantly
improves performance, especially when IOMMU has a little TLB
cache. This can be easily observed when multimedia devices do
processing of RGB data with 90/270 degree rotation
Image rotation is distinctly an operation that needs to bounce around
through memory, so it makes sense that TLB efficiency is important
there.
Video decoding, on the other hand, is a fairly sequential operation.
During video decoding it's not expected that we'll be jumping all over
memory. Decoding video is also pretty heavy and the TLB misses aren't a
huge deal. Presumably most HW video acceleration users of dma-mapping
will not care about huge pages and will set DMA_ATTR_ALLOC_SINGLE_PAGES.
Allocating big chunks of memory is quite expensive, especially if we're
doing it repeadly and memory is full. In one (out of tree) usage model
it is common that arm_iommu_alloc_attrs() is called 16 times in a row,
each one trying to allocate 4 MB of memory. This is called whenever the
system encounters a new video, which could easily happen while the
memory system is stressed out. In fact, on certain social media
websites that auto-play video and have infinite scrolling, it's quite
common to see not just one of these 16x4MB allocations but 2 or 3 right
after another. Asking the system even to do a small amount of extra
work to give us big chunks in this case is just not a good use of time.
Allocating big chunks of memory is also expensive indirectly. Even if
we ask the system not to do ANY extra work to allocate _our_ memory,
we're still potentially eating up all big chunks in the system.
Presumably there are other users in the system that aren't quite as
flexible and that actually need these big chunks. By eating all the big
chunks we're causing extra work for the rest of the system. We also may
start making other memory allocations fail. While the system may be
robust to such failures (as is the case with dwc2 USB trying to allocate
buffers for Ethernet data and with WiFi trying to allocate buffers for
WiFi data), it is yet another big performance hit.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The __iommu_alloc_buffer() is expected to be called to allocate pretty
sizeable buffers. Upon simple tests of video I saw it trying to
allocate 4,194,304 bytes. The function tries to allocate large chunks
in order to optimize IOMMU TLB usage.
The current function is very, very slow.
One problem is the way it keeps trying and trying to allocate big
chunks. Imagine a very fragmented memory that has 4M free but no
contiguous pages at all. Further imagine allocating 4M (1024 pages).
We'll do the following memory allocations:
- For page 1:
- Try to allocate order 10 (no retry)
- Try to allocate order 9 (no retry)
- ...
- Try to allocate order 0 (with retry, but not needed)
- For page 2:
- Try to allocate order 9 (no retry)
- Try to allocate order 8 (no retry)
- ...
- Try to allocate order 0 (with retry, but not needed)
- ...
- ...
Total number of calls to alloc() calls for this case is:
sum(int(math.log(i, 2)) + 1 for i in range(1, 1025))
=> 9228
The above is obviously worse case, but given how slow alloc can be we
really want to try to avoid even somewhat bad cases. I timed the old
code with a device under memory pressure and it wasn't hard to see it
take more than 120 seconds to allocate 4 megs of memory! (NOTE: testing
was done on kernel 3.14, so possibly mainline would behave
differently).
A second problem is that allocating big chunks under memory pressure
when we don't need them is just not a great idea anyway unless we really
need them. We can make due pretty well with smaller chunks so it's
probably wise to leave bigger chunks for other users once memory
pressure is on.
Let's adjust the allocation like this:
1. If a big chunk fails, stop trying to hard and bump down to lower
order allocations.
2. Don't try useless orders. The whole point of big chunks is to
optimize the TLB and it can really only make use of 2M, 1M, 64K and
4K sizes.
We'll still tend to eat up a bunch of big chunks, but that might be the
right answer for some users. A future patch could possibly add a new
DMA_ATTR that would let the caller decide that TLB optimization isn't
important and that we should use smaller chunks. Presumably this would
be a sane strategy for some callers.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There are many locations that do
if (memory_was_allocated_by_vmalloc)
vfree(ptr);
else
kfree(ptr);
but kvfree() can handle both kmalloc()ed memory and vmalloc()ed memory
using is_vmalloc_addr(). Unless callers have special reasons, we can
replace this branch with kvfree(). Please check and reply if you found
problems.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Jan Kara <jack@suse.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Acked-by: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Acked-by: David Rientjes <rientjes@google.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: Boris Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
commit db0fa0cb01 "scatterlist: use sg_phys()" did replacements of
the form:
phys_addr_t phys = page_to_phys(sg_page(s));
phys_addr_t phys = sg_phys(s) & PAGE_MASK;
However, this breaks platforms where sizeof(phys_addr_t) >
sizeof(unsigned long). Revert for 4.3 and 4.4 to make room for a
combined helper in 4.5.
Cc: <stable@vger.kernel.org>
Cc: Jens Axboe <axboe@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Fixes: db0fa0cb01 ("scatterlist: use sg_phys()")
Suggested-by: Joerg Roedel <joro@8bytes.org>
Reported-by: Vitaly Lavrov <vel21ripn@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
__GFP_WAIT has been used to identify atomic context in callers that hold
spinlocks or are in interrupts. They are expected to be high priority and
have access one of two watermarks lower than "min" which can be referred
to as the "atomic reserve". __GFP_HIGH users get access to the first
lower watermark and can be called the "high priority reserve".
Over time, callers had a requirement to not block when fallback options
were available. Some have abused __GFP_WAIT leading to a situation where
an optimisitic allocation with a fallback option can access atomic
reserves.
This patch uses __GFP_ATOMIC to identify callers that are truely atomic,
cannot sleep and have no alternative. High priority users continue to use
__GFP_HIGH. __GFP_DIRECT_RECLAIM identifies callers that can sleep and
are willing to enter direct reclaim. __GFP_KSWAPD_RECLAIM to identify
callers that want to wake kswapd for background reclaim. __GFP_WAIT is
redefined as a caller that is willing to enter direct reclaim and wake
kswapd for background reclaim.
This patch then converts a number of sites
o __GFP_ATOMIC is used by callers that are high priority and have memory
pools for those requests. GFP_ATOMIC uses this flag.
o Callers that have a limited mempool to guarantee forward progress clear
__GFP_DIRECT_RECLAIM but keep __GFP_KSWAPD_RECLAIM. bio allocations fall
into this category where kswapd will still be woken but atomic reserves
are not used as there is a one-entry mempool to guarantee progress.
o Callers that are checking if they are non-blocking should use the
helper gfpflags_allow_blocking() where possible. This is because
checking for __GFP_WAIT as was done historically now can trigger false
positives. Some exceptions like dm-crypt.c exist where the code intent
is clearer if __GFP_DIRECT_RECLAIM is used instead of the helper due to
flag manipulations.
o Callers that built their own GFP flags instead of starting with GFP_KERNEL
and friends now also need to specify __GFP_KSWAPD_RECLAIM.
The first key hazard to watch out for is callers that removed __GFP_WAIT
and was depending on access to atomic reserves for inconspicuous reasons.
In some cases it may be appropriate for them to use __GFP_HIGH.
The second key hazard is callers that assembled their own combination of
GFP flags instead of starting with something like GFP_KERNEL. They may
now wish to specify __GFP_KSWAPD_RECLAIM. It's almost certainly harmless
if it's missed in most cases as other activity will wake kswapd.
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Vitaly Wool <vitalywool@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
IOMMU-based dma_mmap() implementation lacked proper support for offset
parameter used in mmap call (it always assumed that mapping starts from
offset zero). This patch adds support for offset parameter to IOMMU-based
implementation.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: stable@vger.kernel.org # v3.6+
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
dma_mmap() function in IOMMU-based dma-mapping implementation lacked
a check for valid range of mmap parameters (offset and buffer size), what
might have caused access beyond the allocated buffer. This patch fixes
this issue.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: stable@vger.kernel.org # v3.6+
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull ARM fixes from Russell King:
"Three fixes and a resulting cleanup for -rc2:
- Andre Przywara reported that he was seeing a warning with the new
cast inside DMA_ERROR_CODE's definition, and fixed the incorrect
use.
- Doug Anderson noticed that kgdb causes a "scheduling while atomic"
bug.
- OMAP5 folk noticed that their Thumb-2 compiled X servers crashed
when enabling support to cover ARMv6 CPUs due to a kernel bug
leaking some conditional context into the signal handler"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8425/1: kgdb: Don't try to stop the machine when setting breakpoints
ARM: 8437/1: dma-mapping: fix build warning with new DMA_ERROR_CODE definition
ARM: get rid of needless #if in signal handling code
ARM: fix Thumb2 signal handling when ARMv6 is enabled
Commit 96231b2686: ("ARM: 8419/1: dma-mapping: harmonize definition
of DMA_ERROR_CODE") changed the definition of DMA_ERROR_CODE to use
dma_addr_t, which makes the compiler barf on assigning this to an
"int" variable on ARM with LPAE enabled:
*************
In file included from /src/linux/include/linux/dma-mapping.h:86:0,
from /src/linux/arch/arm/mm/dma-mapping.c:21:
/src/linux/arch/arm/mm/dma-mapping.c: In function '__iommu_create_mapping':
/src/linux/arch/arm/include/asm/dma-mapping.h:16:24: warning:
overflow in implicit constant conversion [-Woverflow]
#define DMA_ERROR_CODE (~(dma_addr_t)0x0)
^
/src/linux/arch/arm/mm/dma-mapping.c:1252:15: note: in expansion of
macro DMA_ERROR_CODE'
int i, ret = DMA_ERROR_CODE;
^
*************
Remove the actually unneeded initialization of "ret" in
__iommu_create_mapping() and move the variable declaration inside the
for-loop to make the scope of this variable more clear.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since 2009 we have a nice asm-generic header implementing lots of DMA API
functions for architectures using struct dma_map_ops, but unfortunately
it's still missing a lot of APIs that all architectures still have to
duplicate.
This series consolidates the remaining functions, although we still need
arch opt outs for two of them as a few architectures have very
non-standard implementations.
This patch (of 5):
The coherent DMA allocator works the same over all architectures supporting
dma_map operations.
This patch consolidates them and converges the minor differences:
- the debug_dma helpers are now called from all architectures, including
those that were previously missing them
- dma_alloc_from_coherent and dma_release_from_coherent are now always
called from the generic alloc/free routines instead of the ops
dma-mapping-common.h always includes dma-coherent.h to get the defintions
for them, or the stubs if the architecture doesn't support this feature
- checks for ->alloc / ->free presence are removed. There is only one
magic instead of dma_map_ops without them (mic_dma_ops) and that one
is x86 only anyway.
Besides that only x86 needs special treatment to replace a default devices
if none is passed and tweak the gfp_flags. An optional arch hook is provided
for that.
[linux@roeck-us.net: fix build]
[jcmvbkbc@gmail.com: fix xtensa]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull ARM development updates from Russell King:
"Included in this update:
- moving PSCI code from ARM64/ARM to drivers/
- removal of some architecture internals from global kernel view
- addition of software based "privileged no access" support using the
old domains register to turn off the ability for kernel
loads/stores to access userspace. Only the proper accessors will
be usable.
- addition of early fixup support for early console
- re-addition (and reimplementation) of OMAP special interconnect
barrier
- removal of finish_arch_switch()
- only expose cpuX/online in sysfs if hotpluggable
- a number of code cleanups"
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (41 commits)
ARM: software-based priviledged-no-access support
ARM: entry: provide uaccess assembly macro hooks
ARM: entry: get rid of multiple macro definitions
ARM: 8421/1: smp: Collapse arch_cpu_idle_dead() into cpu_die()
ARM: uaccess: provide uaccess_save_and_enable() and uaccess_restore()
ARM: mm: improve do_ldrd_abort macro
ARM: entry: ensure that IRQs are enabled when calling syscall_trace_exit()
ARM: entry: efficiency cleanups
ARM: entry: get rid of asm_trace_hardirqs_on_cond
ARM: uaccess: simplify user access assembly
ARM: domains: remove DOMAIN_TABLE
ARM: domains: keep vectors in separate domain
ARM: domains: get rid of manager mode for user domain
ARM: domains: move initial domain setting value to asm/domains.h
ARM: domains: provide domain_mask()
ARM: domains: switch to keeping domain value in register
ARM: 8419/1: dma-mapping: harmonize definition of DMA_ERROR_CODE
ARM: 8417/1: refactor bitops functions with BIT_MASK() and BIT_WORD()
ARM: 8416/1: Feroceon: use of_iomap() to map register base
ARM: 8415/1: early fixmap support for earlycon
...
Pull SG updates from Jens Axboe:
"This contains a set of scatter-gather related changes/fixes for 4.3:
- Add support for limited chaining of sg tables even for
architectures that do not set ARCH_HAS_SG_CHAIN. From Christoph.
- Add sg chain support to target_rd. From Christoph.
- Fixup open coded sg->page_link in crypto/omap-sham. From
Christoph.
- Fixup open coded crypto ->page_link manipulation. From Dan.
- Also from Dan, automated fixup of manual sg_unmark_end()
manipulations.
- Also from Dan, automated fixup of open coded sg_phys()
implementations.
- From Robert Jarzmik, addition of an sg table splitting helper that
drivers can use"
* 'for-4.3/sg' of git://git.kernel.dk/linux-block:
lib: scatterlist: add sg splitting function
scatterlist: use sg_phys()
crypto/omap-sham: remove an open coded access to ->page_link
scatterlist: remove open coded sg_unmark_end instances
crypto: replace scatterwalk_sg_chain with sg_chain
target/rd: always chain S/G list
scatterlist: allow limited chaining without ARCH_HAS_SG_CHAIN
This patch allows the use of CMA for DMA coherent memory allocation.
At the moment if the input parameter "is_coherent" is set to true
the allocation is not made using the CMA, which I think is not the
desired behaviour.
The patch covers the allocation and free of memory for coherent
DMA.
Signed-off-by: Lorenzo Nava <lorenx4@gmail.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The dmac_* functions are private to the ARM DMA API implementation, and
should not be used by drivers. In order to discourage their use, remove
their prototypes and macros from asm/*.h.
We have to leave dmac_flush_range() behind as Exynos and MSM IOMMU code
use these; once these sites are fixed, this can be moved also.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
nr_bitmaps member of mapping structure stores the number of already
allocated bitmaps and it is interpreted as loop iterator (it starts from
0 not from 1), so a comparison against number of possible bitmap
extensions should include this fact. This patch fixes this by changing
the extension failure condition. This issue has been introduced by
commit 4d852ef8c2 ("arm: dma-mapping: Add
support to extend DMA IOMMU mappings").
Reported-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Hyungwon Hwang <human.hwang@samsung.com>
Cc: stable@vger.kernel.org # v3.15+
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When dma-coherent transfers are enabled, the mmap call must
not change the pg_prot flags in the vma struct.
Split the arm_dma_mmap into a common and specific parts,
and add a "arm_coherent_dma_mmap" implementation that does
not alter the page protection flags.
Tested on a topic-miami board (Zynq) using the ACP port
to transfer data between FPGA and CPU using the Dyplo
framework. Without this patch, byte-wise access to mmapped
coherent DMA memory was about 20x slower because of the
memory being marked as non-cacheable, and transfer speeds
would not exceed 240MB/s.
After this patch, the mapped memory is cacheable and the
transfer speed is again 600MB/s (limited by the FPGA) when
the data is in the L2 cache, while data integrity is being
maintained.
The patch has no effect on non-coherent DMA.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch 22b3c181c6 ("arm: dma-mapping: limit
IOMMU mapping size") added a check for IO address space size. However
this patch broke IOMMU initialization for typical platforms initialized
from device tree, which get the default IO address space size of 4GiB.
This value doesn't fit into size_t and fails a check introduced by that
commit resulting in failed dma-mapping/iommu initialization. This patch
fixes this issue by adding proper support for full 4GiB address space
size.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull ARM updates from Russell King:
"Included in this update are both some long term fixes and some new
features.
Fixes:
- An integer overflow in the calculation of ELF_ET_DYN_BASE.
- Avoiding OOMs for high-order IOMMU allocations
- SMP requires the data cache to be enabled for synchronisation
primitives to work, so prevent the CPU_DCACHE_DISABLE option being
visible on SMP builds.
- A bug going back 10+ years in the noMMU ARM94* CPU support code,
where it corrupts registers. Found by folk getting Linux running
on their cameras.
- Versatile Express needs an errata workaround enabled for CPU
hot-unplug to work.
Features:
- Clean up module linker by handling out of range relocations
separately from relocation cases we don't handle.
- Fix a long term bug in the pci_mmap_page_range() code, which we
hope won't impact userspace (we hope there's no users of the
existing broken interface.)
- Don't map DMA coherent allocations when we don't have a MMU.
- Drop experimental status for SMP_ON_UP.
- Warn when DT doesn't specify ePAPR mandatory cache properties.
- Add documentation concerning how we find the start of physical
memory for AUTO_ZRELADDR kernels, detailing why we have chosen the
mask and the implications of changing it.
- Updates from Ard Biesheuvel to address some issues with large
kernels (such as allyesconfig) failing to link.
- Allow hibernation to work on modern (ARMv7) CPUs - this appears to
have never worked in the past on these CPUs.
- Enable IRQ_SHOW_LEVEL, which changes the /proc/interrupts output
format (hopefully without userspace breaking... let's hope that if
it causes someone a problem, they tell us.)
- Fix tegra-ahb DT offsets.
- Rework ARM errata 643719 code (and ARMv7 flush_cache_louis()/
flush_dcache_all()) code to be more efficient, and enable this
errata workaround by default for ARMv7+SMP CPUs. This complements
the Versatile Express fix above.
- Rework ARMv7 context code for errata 430973, so that only Cortex A8
CPUs are impacted by the branch target buffer flush when this
errata is enabled. Also update the help text to indicate that all
r1p* A8 CPUs are impacted.
- Switch ARM to the generic show_mem() implementation, it conveys all
the information which we were already reporting.
- Prevent slow timer sources being used for udelay() - timers running
at less than 1MHz are not useful for this, and can cause udelay()
to return immediately, without any wait. Using such a slow timer
is silly.
- VDSO support for 32-bit ARM, mainly for gettimeofday() using the
ARM architected timer.
- Perf support for Scorpion performance monitoring units"
vdso semantic conflict fixed up as per linux-next.
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (52 commits)
ARM: update errata 430973 documentation to cover Cortex A8 r1p*
ARM: ensure delay timer has sufficient accuracy for delays
ARM: switch to use the generic show_mem() implementation
ARM: proc-v7: avoid errata 430973 workaround for non-Cortex A8 CPUs
ARM: enable ARM errata 643719 workaround by default
ARM: cache-v7: optimise test for Cortex A9 r0pX devices
ARM: cache-v7: optimise branches in v7_flush_cache_louis
ARM: cache-v7: consolidate initialisation of cache level index
ARM: cache-v7: shift CLIDR to extract appropriate field before masking
ARM: cache-v7: use movw/movt instructions
ARM: allow 16-bit instructions in ALT_UP()
ARM: proc-arm94*.S: fix setup function
ARM: vexpress: fix CPU hotplug with CT9x4 tile.
ARM: 8276/1: Make CPU_DCACHE_DISABLE depend on !SMP
ARM: 8335/1: Documentation: DT bindings: Tegra AHB: document the legacy base address
ARM: 8334/1: amba: tegra-ahb: detect and correct bogus base address
ARM: 8333/1: amba: tegra-ahb: fix register offsets in the macros
ARM: 8339/1: Enable CONFIG_GENERIC_IRQ_SHOW_LEVEL
ARM: 8338/1: kexec: Relax SMP validation to improve DT compatibility
ARM: 8337/1: mm: Do not invoke OOM for higher order IOMMU DMA allocations
...
IOMMU should be able to use single pages as well as bigger blocks, so if
higher order allocations fail, we should not affect state of the system,
with events such as OOM killer, but rather fall back to order 0
allocations.
This patch changes the behavior of ARM IOMMU DMA allocator to use
__GFP_NORETRY, which bypasses OOM invocation, for orders higher than
zero and, only if that fails, fall back to normal order 0 allocation
which might invoke OOM killer.
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When using the IOMMU-backed DMA ops for a device, we store a pointer to
the dma_iommu_mapping structure (used to keep track of the address
space) in the archdata.mapping field of the struct device.
Rather than access this field directly, use the to_dma_iommu_mapping
helper in dma-mapping, so that we don't really care where the mapping
information is held.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arm_iommu_create_mapping() has size parameter of size_t and
arm_setup_iommu_dma_ops() can take a value higher than that
when this is called from the OF code. So limit the size to
SIZE_MAX.
Tested-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com> (AMD Seattle)
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
CC: Joerg Roedel <joro@8bytes.org>
CC: Grant Likely <grant.likely@linaro.org>
CC: Rob Herring <robh+dt@kernel.org>
CC: Russell King <linux@arm.linux.org.uk>
CC: Arnd Bergmann <arnd@arndb.de>
When validating the mask against the amount of memory we have available
(so that we can trap 32-bit DMA addresses with >32-bits memory), we had
not taken account of the fact that max_pfn is the maximum PFN number
plus one that would be in the system.
There are several references in the code which bear this out:
mm/page_owner.c:
for (; pfn < max_pfn; pfn++) {
}
arch/x86/kernel/setup.c:
high_memory = (void *)__va(max_pfn * PAGE_SIZE - 1)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Even without an iommu, NO_KERNEL_MAPPING is still convenient to save on
kernel address space in places where we don't need a kernel mapping.
Implement support for it in the two places where we're creating an
expensive mapping.
__alloc_from_pool uses an internal pool from which we already have
virtual addresses, so it's not relevant, and __alloc_simple_buffer uses
alloc_pages, which will always return a lowmem page, which is already
mapped into kernel space, so we can't prevent a mapping for it in that
case.
Signed-off-by: Jasper St. Pierre <jstpierre@mecheye.net>
Signed-off-by: Carlo Caione <carlo@caione.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Daniel Drake <dsd@endlessm.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull ARM fix from Russell King:
"Just one fix this time around. __iommu_alloc_buffer() can cause a
BUG() if dma_alloc_coherent() is called with either __GFP_DMA32 or
__GFP_HIGHMEM set. The patch from Alexandre addresses this"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8305/1: DMA: Fix kzalloc flags in __iommu_alloc_buffer()
There doesn't seem to be any valid reason to allocate the pages array
with the same flags as the buffer itself. Doing so can eventually lead
to the following safeguard in mm/slab.c's cache_grow() to be hit:
if (unlikely(flags & GFP_SLAB_BUG_MASK)) {
pr_emerg("gfp: %un", flags & GFP_SLAB_BUG_MASK);
BUG();
}
This happens when buffers are allocated with __GFP_DMA32 or
__GFP_HIGHMEM.
Fix this by allocating the pages array with GFP_KERNEL to follow what is
done elsewhere in this file. Using GFP_KERNEL in __iommu_alloc_buffer()
is safe because atomic allocations are handled by __iommu_alloc_atomic().
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull ARM fixes from Russell King:
"A number of ARM fixes, the biggest is fixing a regression caused by
appended DT blobs exceeding 64K, causing the decompressor fixup code
to fail to patch the DT blob. Another important fix is for the ASID
allocator from Will Deacon which prevents some rare crashes seen on
some systems. Lastly, there's a build fix for v7M systems when printk
support is disabled.
The last two remaining fixes are more cosmetic - the IOMMU one
prevents an annoying harmless warning message, and we disable the
kernel strict memory permissions on non-MMU which can't support it
anyway"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8299/1: mm: ensure local active ASID is marked as allocated on rollover
ARM: 8298/1: ARM_KERNMEM_PERMS only works with MMU enabled
ARM: 8295/1: fix v7M build for !CONFIG_PRINTK
ARM: 8294/1: ATAG_DTB_COMPAT: remove the DT workspace's hardcoded 64KB size
ARM: 8288/1: dma-mapping: don't detach devices without an IOMMU during teardown
