This patch sets STATUS_EXIT_PENDING on pci_remove. Otherwise
iwl4965_down may fail to uninitialize the driver.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch calls apm stop on exit and suspend. Without this patch
hardware consumes power even after driver is removed or suspended.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch "iwlwifi: do not use GFP_DMA in iwl_tx_queue_init" removes
GFP_DMA from allocation tx command buffers. GFP_DMA allows allocation
only for memory under 16M which causes allocation problems
suspend/resume flows.
Using kmalloc is temporal solution and some consistent/coherent
allocation schema will be more correct. Since iwlwifi hardware
supports 64bit address this solution should work on x86 (32 and
64bit) for now.
This patch fixes memory freeing problem in the previous patch.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Ian Schram <ischram@telenet.be>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes rx_chain computation. The code that adjusts number of
rx chains to number supported by HW was missing. Miss configuration
causes firmware error. Note: iwlwifi supports HW with up to 3 RX
chains (2x2, 2x3, 1x2, and 3x3 MIMO). This patch also simplifies the
whole RX chain computation.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the wrong use MIMO power save values. Our TX was
configured with our MIMO power save values instead of peer's MIMO power
save values, this may affect connectivity. The peer STA/AP may not sense
our traffic at all as it doesn't have all RX chains opened.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rx chain might change during power save transitions but it doesn't
require sending Full-ROXN command to the firmware. Full-RXON requires
reconnection to an AP and thus affects user experience. The patch
avoids the Full-RXON by removing the rx_chain modification check in
iwl_full_rxon_required function.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This enables sending of direct probes on passive channels, as long as
traffic was detected on that channel. This enables connectivity to
hidden/non broadcasting SSIDs APs on passive channels. Note 5000 HW
declares all 5.2 spectrum as passive.
Signed-off-by: Cahill Ben <ben.m.cahill@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is a W/A for the TSF sync issue in IBSS merging. HW is not
capable to sync TSF (it's constantly little behind). This creates
constant IBSS merging upon reception of each beacon, adding and removing
station which in turn creates above 50% packet loss and thus dramatically
degrade the throughput. The W/A simply stops the driver from declaring it
has a reliable TSF value and thus eliminates IBSS merging.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove chipset-specific quirk workaround; the workaround caused
unrecoverable DMA lockups when the driver was loaded following a
PXE boot.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Michael Brown <mbrown@fensystems.co.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This commit dropped the setting of the default interrupt throttle rate.
commit 021230d40a
Author: Ayyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Date: Mon Mar 3 15:03:45 2008 -0800
ixgbe: Introduce MSI-X queue vector code
The following patch adds it back. Without this the default value of 0
causes the performance of this card to be awful. Restoring these to the
default values yields much better performance.
This regression has been around since 2.6.25.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: stable@kernel.org [2.6.25 and later]
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Make the "pegasus" driver scream less loudly in the face of
problems as it initializes, avoiding hundreds of messages:
- ratelimit some key error messages
- avoid some spurious diagnostics caused by strange codeflow
And fix one instance of goofy indentation.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
ipsec: Fix deadlock in xfrm_state management.
ipv: Re-enable IP when MTU > 68
net/xfrm: Use an IS_ERR test rather than a NULL test
ath9: Fix ath_rx_flush_tid() for IRQs disabled kernel warning message.
ath9k: Incorrect key used when group and pairwise ciphers are different.
rt2x00: Compiler warning unmasked by fix of BUILD_BUG_ON
mac80211: Fix debugfs union misuse and pointer corruption
wireless/libertas/if_cs.c: fix memory leaks
orinoco: Multicast to the specified addresses
iwlwifi: fix 64bit platform firmware loading
iwlwifi: fix apm_stop (wrong bit polarity for FLAG_INIT_DONE)
iwlwifi: workaround interrupt handling no some platforms
iwlwifi: do not use GFP_DMA in iwl_tx_queue_init
net/wireless/Kconfig: clarify the description for CONFIG_WIRELESS_EXT_SYSFS
net: Unbreak userspace usage of linux/mroute.h
pkt_sched: Fix locking of qdisc_root with qdisc_root_sleeping_lock()
ipv6: When we droped a packet, we should return NET_RX_DROP instead of 0
Fix a bug reported by and diagnosed by Aaron Straus.
This is a regression intruduced into 2.6.26 by
commit adc782dae6
Author: Matt Mackall <mpm@selenic.com>
Date: Tue Apr 29 01:03:07 2008 -0700
random: simplify and rename credit_entropy_store
credit_entropy_bits() does:
spin_lock_irqsave(&r->lock, flags);
...
if (r->entropy_count > r->poolinfo->POOLBITS)
r->entropy_count = r->poolinfo->POOLBITS;
so there is a time window in which this BUG_ON():
static size_t account(struct entropy_store *r, size_t nbytes, int min,
int reserved)
{
unsigned long flags;
BUG_ON(r->entropy_count > r->poolinfo->POOLBITS);
/* Hold lock while accounting */
spin_lock_irqsave(&r->lock, flags);
can trigger.
We could fix this by moving the assertion inside the lock, but it seems
safer and saner to revert to the old behaviour wherein
entropy_store.entropy_count at no time exceeds
entropy_store.poolinfo->POOLBITS.
Reported-by: Aaron Straus <aaron@merfinllc.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: <stable@kernel.org> [2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update rtc-cmos shutdown handling to leave RTC alarms active, resolving
http://bugzilla.kernel.org/show_bug.cgi?id=11411 on several boards. There
are still some systems where the ACPI event handling doesn't cooperate.
(Possibly related to bugid 11312, reporting the spontaneous disabling of
RTC events.)
Bug 11411 reported that changes to work around some ACPI event issues
broke wake-from-S5 handling, as used for DVR applications. (They like to
power off, then wake later to record programs.)
[yakui.zhao@intel.com: add shutdown for PNP devices]
[dbrownell@users.sourceforge.net: update comments]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Stefan Bauer <stefan.bauer@cs.tu-chemnitz.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I got this patch through Red Hat's bugzilla from the bug submitter and
patch creator. I have just fixed it up so it applies without fuzz to
upstream kernels.
Original patch and description from Shyam kumar Iyer:
The issue [ibft module not displaying targets with short names] is because
of an offset calculatation error in the iscsi_ibft.c code. Due to this
error directory structure for the target in /sys/firmware/ibft does not
get created and so the initiator is unable to connect to the target.
Note that this bug surfaced only with an name that had a short section at
the end. eg: "iqn.1984-05.com.dell:dell". It did not surface when the
iqn's had a longer section at the end. eg:
"iqn.2001-04.com.example:storage.disk2.sys1.xyz"
So, the eot_offset was calculated such that an extra 48 bytes i.e. the
size of the ibft_header which has already been accounted was subtracted
twice.
This was not evident with longer iqn names because they would overshoot
the total ibft length more than 48 bytes and thus would escape the bug.
Signed-off-by: Shyam Kumar Iyer <shyam_iyer@dell.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Konrad Rzeszutek <konrad@virtualiron.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
commit 945185a69d ("rtc: rtc_time_to_tm: use
unsigned arithmetic") changed the some types in rtc_time_to_tm() to
unsigned:
void rtc_time_to_tm(unsigned long time, struct rtc_time *tm)
{
- register int days, month, year;
+ unsigned int days, month, year;
This doesn't work for all cases, because days is checked for < 0 later
on:
if (days < 0) {
year -= 1;
days += 365 + LEAP_YEAR(year);
}
I think the correct fix would be to keep days signed and do an appropriate
cast later on.
Signed-off-by: Jan Altenberg <jan.altenberg@linutronix.de>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If there are more then one graphics card handled by the tdfxfb driver the
name of the frame buffer overruns reserved size.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix memory detection on Voodoo3 cards with SDRAM memory.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It turns out that event 0x4 merely indcates that a hotkey has been
pressed, not which one. A further query is required in order to determine
the actual keypress. The following patch adds support for that along with
the known keycodes.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
hp-wmi currently changes the RFKill state by altering the struct members
rather than using the dedicated interface, meaning that update events
won't be pushed to userspace. This patch fixes that, along with fixing
the declared type of the WWAN kill switch. It also ensures that rfkill
interfaces are only registered for hardware that exists.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Ivo van Doorn <ivdoorn@gmail.com>
Cc: Dave Young <hidave.darkstar@gmail.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1. Check if virtual resolution fits into memory.
Otherwise, Linux hangs during panning.
2. When selected use all available memory to
maximize yres_virtual to speed up panning
(previously also xres_virtual was increased).
3. Simplify memory restriction calculations.
Signed-off-by: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
At91_mci is abusing dma_free_coherent(), which may not be called with IRQs
disabled. I saw "mkfs.ext3" on an MMC card objecting voluminously as each
write completed:
WARNING: at arch/arm/mm/consistent.c:368 dma_free_coherent+0x2c/0x224()
[<c002726c>] (dump_stack+0x0/0x14) from [<c00387d4>] (warn_on_slowpath+0x4c/0x68)
[<c0038788>] (warn_on_slowpath+0x0/0x68) from [<c0028768>] (dma_free_coherent+0x2c/0x224)
r6:00008008 r5:ffc06000 r4:00000000
[<c002873c>] (dma_free_coherent+0x0/0x224) from [<c01918ac>] (at91_mci_irq+0x374/0x420)
[<c0191538>] (at91_mci_irq+0x0/0x420) from [<c0065d9c>] (handle_IRQ_event+0x2c/0x6c)
...
This bug has been around for a LONG time. The MM warning is from late
2005, but the driver merged a year later ... so I'm puzzled why nobody
noticed this before now.
The fix involves noting that this buffer shouldn't be DMA-coherent; it's
just used for normal DMA writes. So replace it with standard kmalloc()
buffering and DMA mapping calls.
This is the quickie fix. A better one would not rely on allocating large
bounce buffers. (Note that dma_alloc_coherent could have failed too, but
that case was ignored... kmalloc is a bit more likely to fail though.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Pierre Ossman <drzeus-mmc@drzeus.cx>
Cc: Andrew Victor <linux@maxim.org.za>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recent changes to tighten the check for UARTs that don't correctly
re-assert THRE (01c194d927: "serial 8250:
tighten test for using backup timer") caused problems when such a UART was
opened for the second time - the bug could only successfully be detected
at first initialization. For users of this version of this particular
UART IP it is fatal.
This patch stores the information about the bug in the bugs field of the
port structure when the port is first started up so subsequent opens can
check this bit even if the test for the bug fails.
David Brownell: "My own exposure to this is that the UART on DaVinci
hardware, which TI allegedly derived from its original 16550 logic, has
periodically gone from working to unusable with the mainline 8250.c ...
and back and forth a bunch. Currently it's "unusable", a regression from
some previous versions. With this patch from Will, it's usable."
Signed-off-by: Will Newton <will.newton@gmail.com>
Acked-by: Alex Williamson <alex.williamson@hp.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: David Brownell <david-b@pacbell.net>
Cc: <stable@kernel.org> [2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The exit function neglects to remove debugfs entries, leading to a BUG
on reload.
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Russ Dill <Russ.Dill@gmail.com>
Acked-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Cc: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch addresses an issue with the locking order. ath_rx_flush_tid()
uses spin_lock/unlock_bh when IRQs are disabled in sta_notify by mac80211.
As node clean up is still pending with ath9k and this problematic portion
of the code is expected to change anyway, thinking of a proper fix may not
be worthwhile. So having this interim fix helps the users to get rid of the
kernel warning message.
Pasted the kernel warning message for reference.
kernel: ath0: No ProbeResp from current AP 00:1b:11:60:7a:3d - assume out of range
kernel: ------------[ cut here ]------------
kernel: WARNING: at kernel/softirq.c:136 local_bh_enable+0x3c/0xab()
kernel: Pid: 1029, comm: ath9k Not tainted 2.6.27-rc4-wt-w1fi-wl
kernel:
kernel: Call Trace:
kernel: [<ffffffff802278d8>] warn_on_slowpath+0x51/0x77
kernel: [<ffffffff80224c51>] check_preempt_wakeup+0xf3/0x123
kernel: [<ffffffff80239658>] autoremove_wake_function+0x9/0x2e
kernel: [<ffffffff8022c281>] local_bh_enable+0x3c/0xab
kernel: [<ffffffffa01ab75a>] ath_rx_node_cleanup+0x38/0x6e [ath9k]
kernel: [<ffffffffa01b2280>] ath_node_detach+0x3b/0xb6 [ath9k]
kernel: [<ffffffffa01ab09f>] ath9k_sta_notify+0x12b/0x165 [ath9k]
kernel: [<ffffffff802366cf>] queue_work+0x1d/0x49
kernel: [<ffffffffa018c3fc>] add_todo+0x70/0x99 [mac80211]
kernel: [<ffffffffa017de76>] __sta_info_unlink+0x16b/0x19e [mac80211]
kernel: [<ffffffffa017e6ed>] sta_info_unlink+0x18/0x43 [mac80211]
kernel: [<ffffffffa0182732>] ieee80211_associated+0xaa/0x16d [mac80211]
kernel: [<ffffffffa0184a1a>] ieee80211_sta_work+0x4fb/0x6b4 [mac80211]
kernel: [<ffffffff80469c58>] thread_return+0x30/0xa9
kernel: [<ffffffffa018451f>] ieee80211_sta_work+0x0/0x6b4 [mac80211]
kernel: [<ffffffff802362c2>] run_workqueue+0xb1/0x17a
kernel: [<ffffffff80236be9>] worker_thread+0xd0/0xdb
kernel: [<ffffffff8023964f>] autoremove_wake_function+0x0/0x2e
kernel: [<ffffffff80236b19>] worker_thread+0x0/0xdb
kernel: [<ffffffff8023954a>] kthread+0x47/0x75
kernel: [<ffffffff80223121>] schedule_tail+0x18/0x50
kernel: [<ffffffff8020bc49>] child_rip+0xa/0x11
kernel: [<ffffffff80239503>] kthread+0x0/0x75
kernel: [<ffffffff8020bc3f>] child_rip+0x0/0x11
kernel:
kernel: ---[ end trace e9bb5da661055827 ]---
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Updating sc_keytype multiple times when groupwise and pairwise
ciphers are different results in incorrect pairwise key type
assumed for TX control and normal ping fails. This works fine
for cases where both groupwise and pairwise ciphers are same.
Also use mac80211 provided enums for key length calculation.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A "Set" to a sign-bit in an "&" operation causes a compiler warning.
Make calculations unsigned.
[ The warning was masked by the old definition of BUILD_BUG_ON() ]
Also remove __builtin_constant_p from FIELD_CHECK since BUILD_BUG_ON
no longer permits non-const values.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
CC: Ingo Molnar <mingo@elte.hu>
CC: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The leak in if_cs_prog_helper() is obvious.
It looks a bit as if not freeing "fw" in if_cs_prog_real() was done
intentionally, but I'm not seeing why it shouldn't be freed.
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When multicasting the driver sets the number of group addresses using
the count from the previous set multicast command. In general this means
you have to set the multicast addresses twice to get the behaviour you
want.
If we were multicasting, and reduce the number of addresses we are
multicasting to, then the driver would write uninitialised data from the
stack into the group addresses to multicast to.
Only write the multicast addresses we have specifically set.
Signed-off-by: David Kilroy <kilroyd@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes loading firmware from memory above 32bit.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Marcel Holtmann <holtmann@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch fixes CSR_GP_CNTRL_REG_FLAG_INIT_DONE was set instead of
cleared which disabled moving device to D0U state.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds workaround for an interrupt related hardware bug on
some platforms. (Apparently these platforms boot-up w/ INTX_DISABLED
set. -- JWL)
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
GFP_DMA is not necessary for the iwlwifi hardware and it can cause
allocation failures and/or invoke the OOM killer on lots of systems.
For reference:
https://bugzilla.redhat.com/show_bug.cgi?id=459709
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* fix device tree ... don't forget to set the parent device
* let init/exit code be removed where practical
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
[bart: splitted it from bigger DaVinci patch, s/hw.parent/hw.dev/]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* 'for-linus' of git://neil.brown.name/md:
Fix problem with waiting while holding rcu read lock in md/bitmap.c
Remove invalidate_partition call from do_md_stop.
This fixes a typo in commit 2a2a64714d "Disable MWAIT via DMI on broken Compal board".
It allows the nomwait dmi check to actually detect the Acer 5220.
Signed-off-by: Dennis Jansen <dennis.jansen@web.de>
Tested-by: Dennis Jansen <dennis.jansen@web.de>
Acked-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The MEMGETREGIONINFO ioctl() in mtdchar.c was clobbering user memory by
overwriting more than intended, due the size of struct mtd_erase_region_info
changing in commit 0ecbc81adf ('Support
for auto locking flash on power up').
Fix avoids this by copying struct members one by one with put_user(), as there
is no longer a convenient struct to use the size of as the length argument to
copy_to_user().
Signed-off-by: Zev Weiss <zevweiss@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch fixes a memory leak in an error path.
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
A recent patch to protect the rdev list with rcu locking leaves us
with a problem because we can sleep on memalloc while holding the
rcu lock.
The rcu lock is only needed while walking the linked list as
uninteresting devices (failed or spares) can be removed at any time.
So only take the rcu lock while actually walking the linked list.
Take a refcount on the rdev during the time when we drop the lock
and do the memalloc to start IO.
When we return to the locked code, all the interesting devices
on the list will not have moved, so we can simply use
list_for_each_continue_rcu to pick up where we left off.
Signed-off-by: NeilBrown <neilb@suse.de>
When stopping an md array, or just switching to read-only, we
currently call invalidate_partition while holding the mddev lock.
The main reason for this is probably to ensure all dirty buffers
are flushed (invalidate_partition calls fsync_bdev).
However if any dirty buffers are found, it will almost certainly cause
a deadlock as starting writeout will require an update to the
superblock, and performing that updates requires taking the mddev
lock - which is already held.
This deadlock can be demonstrated by running "reboot -f -n" with
a root filesystem on md/raid, and some dirty buffers in memory.
All other calls to stop an array should already happen after a flush.
The normal sequence is to stop using the array (e.g. umount) which
will cause __blkdev_put to call sync_blockdev. Then open the
array and issue the STOP_ARRAY ioctl while the buffers are all still
clean.
So this invalidate_partition is normally a no-op, except for one case
where it will cause a deadlock.
So remove it.
This patch possibly addresses the regression recored in
http://bugzilla.kernel.org/show_bug.cgi?id=11460
and
http://bugzilla.kernel.org/show_bug.cgi?id=11452
though it isn't yet clear how it ever worked.
Signed-off-by: NeilBrown <neilb@suse.de>
If this triggers its bad, however some machines seem to have been
triggering it for ages and we didn't know until we added the debug.
So downgrade the debug now so people don't call this a regression.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch remove blk_register_filter and blk_unregister_filter in
gendisk, and adds them to sd.c, sr.c. and ide-cd.c
The commit abf5439370 moved cmdfilter
from gendisk to request_queue. It turned out that in some subsystems
multiple gendisks share a single request_queue. So we get:
Using physmap partition information
Creating 3 MTD partitions on "physmap-flash":
0x00000000-0x01c00000 : "User FS"
0x01c00000-0x01c40000 : "booter"
kobject (8511c410): tried to init an initialized object, something is seriously wrong.
Call Trace:
[<8036644c>] dump_stack+0x8/0x34
[<8021f050>] kobject_init+0x50/0xcc
[<8021fa18>] kobject_init_and_add+0x24/0x58
[<8021d20c>] blk_register_filter+0x4c/0x64
[<8021c194>] add_disk+0x78/0xe0
[<8027d14c>] add_mtd_blktrans_dev+0x254/0x278
[<8027c8f0>] blktrans_notify_add+0x40/0x78
[<80279c00>] add_mtd_device+0xd0/0x150
[<8027b090>] add_mtd_partitions+0x568/0x5d8
[<80285458>] physmap_flash_probe+0x2ac/0x334
[<802644f8>] driver_probe_device+0x12c/0x244
[<8026465c>] __driver_attach+0x4c/0x84
[<80263c64>] bus_for_each_dev+0x58/0xac
[<802633ec>] bus_add_driver+0xc4/0x24c
[<802648e0>] driver_register+0xcc/0x184
[<80100460>] _stext+0x60/0x1bc
In the long term, we need to fix such subsystems but we need a quick
fix now. This patch add the command filter support to only sd and sr
though it might be useful for other SG_IO users (such as cciss).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Reported-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
Blackfin arch: Fix PM building on BF52x: No ROTWE on BF52x, add USBWE
Blackfin arch: sram: use 'unsigned long' for irqflags
Blackfin arch: let PCI depend on BROKEN
Blackfin arch: move include/asm-blackfin header files to arch/blackfin
Blackfin arch: fix bug - MPU crashes under stress
Blackfin arch: Fix bug - when to rmmod the L1_module, it stucks and then reboot the board.
Blackfin arch: dont actually need to muck with EMAC_SYSTAT for BF52x for demuxing
Blackfin arch: Add MTD Partitions for MTD_DATAFLASH, increase max SPI SCLK
The WWAN radio control has been working well for over three years,
and is no longer experimental.
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Some DVB adapters do not support the special I2C transaction that we
use for probing purposes. There's no point in logging this event, as
there's nothing the user can do and in general there is no actual
problem. So, degrade one of these messages to a debug message, and
move the other one around so that it is only printed on bogus drivers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Uwe Bugla <uwe.bugla@gmx.de>
device_init_wakeup must be called after device_register.
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Initialize the L_Key and R_Key for memory regions returned from
mlx4_ib_alloc_fast_reg_mr(). Otherwise callers just get garbage for
the memory keys and can't do anything useful with these MRs.
Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kanru Chen posted a patch versus the old code which deals with the case
where you resize the pty side of a pty/tty pair. In that situation the
termios data is updated for both pty and tty but the locks are not held
for the right side.
This implements the fix differently against the updated tty code. Patch
by self but the hard bit (noticing and fixing the bug) is thanks to Kanru
Chen.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The termios settings ioctls on a pty should affect the bound tty side not
the pty. The SOFTCAR ioctls use the wrong device file.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'drm-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm: don't set the signal blocker on the master process.
drm: don't call the vblank tasklet with irqs disabled.
r300: Fix cliprect emit
drm/radeon: r300_cmdbuf: Always emit INDX_BUFFER immediately after DRAW_INDEX
radeon: fix some hard lockups on r3/4/500s
Here's the patch. It shrinks the stack from 1152 bytes to 192 bytes (the
first version, that only did the e1000_option part, got it down to 600
bytes). About half comes from not using multiple "e1000_option"
structures, the other half comes from turning the "e1000_opt_list[]"
arrays into "static const" instead, so that gcc doesn't copy them onto the
stack.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reveiewed-by: Auke Kok <auke-jan.h.kok@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: remove blk_queue_tag_depth() and blk_queue_tag_queue()
block: remove unused ->busy part of the block queue tag map
bio: fix __bio_copy_iov() handling of bio->bv_len
bio: fix bio_copy_kern() handling of bio->bv_len
block: submit_bh() inadvertently discards barrier flag on a sync write
block: clean up cmdfilter sysfs interface
block: rename blk_scsi_cmd_filter to blk_cmd_filter
sg: restore command permission for TYPE_SCANNER
block: move cmdfilter from gendisk to request_queue
This reverts commit 5b6155ee70, because
the block device ioctl's really aren't ready for it.
In particular, the "struct file *" and the "struct inode *" arguments do
not necessarily match, which means that the unlocked version of the
ioctl (that only gets a "struct file *") isn't actually able to handle
the cases it needs to handle.
This fixes bugzilla
http://bugzilla.kernel.org/show_bug.cgi?id=11401
Reported-and-bisected-by: Laurent Riffard <laurent.riffard@free.fr>
Acked-by: Peter Osterlund <petero2@telia.com>
Cc: Alan Cox <alan@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There were 2 omitted readb's used on an iomap space. eliminate them
by using ioread8 instead.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When a preallocated header qdio buffer is filled we have to account
the offset for the data length.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
In case the netdev unicast list contains additional entries we have
to register/deregister them.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
return value -ENOTSUPP is not valid in userspace context, use
-EOPNOTSUPP instead.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We must not call dev_mc_add() from within our HW configure which happens
before we initialize and register the netdev. Do it in open() instead.
Thanks to Sebastian Siewior for tracking it down.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix the checksum feature advertised in device flags. The hardware support
TCP/UDP over IPv4 and TCP/UDP over IPv6 (without IPv6 extension headers).
However, the kernel feature flags do not distinguish IPv6 with/without
extension headers.
Therefore, the driver needs to use NETIF_F_IP_CSUM instead of
NETIF_F_HW_CSUM since the latter includes all IPv6 packets.
A future patch can be created to check for extension headers and perform
software checksum calculation.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Manfred Spraul <manfred@colorfullife.com
Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Implement set_mac_address for mcs7830. This enables me to use it with my
cable modem.
Signed-off-by: Oliver Martin <oliver.martin@student.tuwien.ac.at>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This adds USB device IDs for MosChip 7730 and Sitecom LN030
to the mcs7830 driver. The IDs have been reported to work without
further modifications.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: David Brownell <david-b@pacbell.net>
Cc: Viktor Horvath <ViktorHorvath@gmx.net>
Cc: Robbert Wethmar <robbert@wethmar.nl>
Cc: Bart van der Klip <bklip@xs4all.nl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch fixes a ibmveth bug where bad UDP checksums are being transmitted
when checksum offloading is enabled.
The hypervisor does checksum offloading only on TCP packets, so ibmveth calls
skb_checksum_help() for any other protocol. The bug happens because
the packet is being modified after the DMA map, so we would need a memory
barrier before making the hypervisor call. Reordering the code so that the
DMA map happens after skb_checksum_help() has the additional advantage of
fixing a DMA map leak if skb_checksum_help() where to fail.
Signed-off-by: Santiago Leon <santil@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fixes dev_kfree_skb happening too many times when hso_start_net_device
is called from hso_resume.
Signed-off-by: Denis Joseph Barrow <D.Barow@option.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The atl1 driver is causing stalled connections and file corruption
whenever TSO is enabled. Two examples are here:
http://lkml.org/lkml/2008/7/15/325http://lkml.org/lkml/2008/8/18/543
Disable TSO by default until we can determine the source of the
problem.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Doesn't cause problems (yet) because err gets zeroed earlier.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Disable support for device 8086:10E8. Currently the result of loading the
driver with the device present causes system instability.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
CC [M] drivers/net/skfp/ess.o
drivers/net/skfp/ess.c: In function 'ess_send_response':
drivers/net/skfp/ess.c:513: warning: cast from pointer to integer of different size
drivers/net/skfp/ess.c: In function 'ess_send_alc_req':
drivers/net/skfp/ess.c:609: warning: cast from pointer to integer of different size
drivers/net/skfp/ess.c:639: warning: cast from pointer to integer of different size
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
LCS recovery dumps in irq routine when CCW address in
Subchannel Status Word (SCSW) is zero. This occurs
when recovery is driven after cable reconnect.
Signed-off-by: Klaus-D. Wacker <kdwacker@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use netdev->ml_priv instead of netdev->priv
Signed-off-by: Peter Tiedemann <ptiedem@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use netdev->ml_priv instead of netdev->priv
Signed-off-by: Peter Tiedemann <ptiedem@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
probe_error() frees memory only, if cgdev->dev.driver_data refers
to the claw_privbk structure. Move forward its setting in claw_probe()
to ensure proper freeing of claw_privbk allocations.
Cc: Daniel <danielm77@spray.se>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The real_num_tx_queues was not being set when in MSI-X only mode. This patch
corrects that path so all interrupt types are correctly configured.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Ethtool -d is reading the EICR and ICR registers which is currently
clearing these registers and masking off interrupts. To prevent this we
read the EICS and ICS equivilents as they can be read without clearing or
masking.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Set the EICS bit for each of the RX queues at least once every 2 seconds to
prevent the rx queues from stalling.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The leak hurts with swiotlb and jumbo frames.
Fix http://bugzilla.kernel.org/show_bug.cgi?id=9468.
Heavily hinted by Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Alistair John Strachan <alistair@devzero.co.uk>
Tested-by: Timothy J Fontaine <tjfontaine@atxconsulting.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
VLAN filtering is broken, due to reading the incorrect register for
the VLAN filtering settings. Fixed by reading/writing the correct
register.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
so update things accordingly
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
sg allowed any command for TYPE_SCANNER. The cmd_filter patchset
doesn't. We can't change sg's permission since it might break the
existing software.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
cmd_filter works only for the block layer SG_IO with SCSI block
devices. It breaks scsi/sg.c, bsg, and the block layer SG_IO with SCSI
character devices (such as st). We hit a kernel crash with them.
The problem is that cmd_filter code accesses to gendisk (having struct
blk_scsi_cmd_filter) via inode->i_bdev->bd_disk. It works for only
SCSI block device files. With character device files, inode->i_bdev
leads you to struct cdev. inode->i_bdev->bd_disk->blk_scsi_cmd_filter
isn't safe.
SCSI ULDs don't expose gendisk; they keep it private. bsg needs to be
independent on any protocols. We shouldn't change ULDs to expose their
gendisk.
This patch moves struct blk_scsi_cmd_filter from gendisk to
request_queue, a common object, which eveyone can access to.
The user interface doesn't change; users can change the filters via
/sys/block/. gendisk has a pointer to request_queue so the cmd_filter
code accesses to struct blk_scsi_cmd_filter.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
bintval is set to the initial value at .config_interface which is too
late, since it overwrites previously set value from .config. Move the
initialization to the .add_interface.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Beacons setup and config was racy with beacon send. Ensure that
ISR and reset functions see consistent state of bbuf.
Use also dev_kfree_skb_any in ath5k_txbuf_free since we call it
from atomic now.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the AP rejects a Shared Key authentication request, try Open System
auth too.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Return errors from request_firmware() (like other drivers that do
firmware load on device open) and make up plausible codes for other
error conditions. Gives userspace tools like NetworkManager a clue that
firmware may be missing when the result of setting IFF_UP is ENOENT.
Signed-off-by: Dan Williams <dcbw@redhat.com>
v2: fix reversed check of atmel_wakeup_firmware() in probe_atmel_card()
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The drivers below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
drivers/watchdog/pc87413_wdt.c
This patch removes the said #include <version.h>.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Fix the following build error when mpc8xxx_wdt is selected to build as a
module:
drivers/watchdog/mpc8xxx_wdt.c:304: error: redefinition of '__inittest'
drivers/watchdog/mpc8xxx_wdt.c:298: error: previous definition of '__inittest' was here
drivers/watchdog/mpc8xxx_wdt.c:304: error: redefinition of 'init_module'
drivers/watchdog/mpc8xxx_wdt.c:298: error: previous definition of 'init_module' was here
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
This patch adds support for the built-in RDC R-321x SoC watchdog.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The watchdog driver mpc8xx_wdt.c was a device interface to
arch/ppc/syslib/m8xx_wdt.c for MPC8xx hardware. Now that ARCH=ppc is
gone, this driver is of no more use. For ARCH=powerpc, MPC8xx hardware
is supported by mpc8xxx_wdt.c.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Remove the changelog from the top of the driver, which
is redundant as this information is more accurately
represented from the revision control holding the
file.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Fix comparison of a pointer to 0, instead of using
NULL for a invalid pointer.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
If an error occurs on opcontrol start, the event and per cpu buffers
are released. If later opcontrol shutdown is called then the free
function will be called again to free buffers that no longer
exist. This results in a kernel oops. The following changes
prevent the call to delete buffers that don't exist.
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The multi queue support is still disabled by default for the bnx2x
(needs some more testing and validation), but there are 2 obvious bug in
it which are fixed in this patch
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixing the order of enabling and disabling NAPI and the interrupts
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Load failures were not handled correctly
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TPA initialization is part of the FW internal memory initialization
and so it is moved to the appropriate function
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increasing the lock timeout to 5 seconds instead of 1 second to minimize
the chance of failures due to timeout
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After iSCSI boot, the HW lock should only protect the flag so only the
first function will reset the chip and not then entire chip reset
process
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The A1021G board is also using the fan failure mechanism in the same way
the A1022G board does
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The has Rx work check was wrong: when the FW was at the end of the page,
the driver was already at the beginning of the next page. Since the
check only validated that both driver and FW are pointing to the same
place, it concluded that there is still work to be done. This caused
some serious issues including long latency results on ping-pong test and
lockups while unloading the driver in that condition.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: fix reference leak in pci_get_dev_by_id()
PCI: shpchp: Rename duplicate slot name N as N-1, N-2, N-M...
PCI: pciehp: Rename duplicate slot name N as N-1, N-2, N-M...
Fix this compile bug:
CC drivers/s390/block/dcssblk.o
drivers/s390/block/dcssblk.c: In function 'dcssblk_add_store':
drivers/s390/block/dcssblk.c:387: error: implicit declaration of function 'dcssblk_get_segment_by_name'
drivers/s390/block/dcssblk.c:389: error: label 'release_gd' used but not defined
make[1]: *** [drivers/s390/block/dcssblk.o] Error 1
make: *** [drivers/s390/block/] Error 2
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This is the last use of (the deprecated) stop_machine_run in the tree.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Both v and vb->num_pages are u32 and unsigned int respectively. If v is less
than vb->num_pages (and it is, when deflating the balloon), the result is a
very large 32-bit number. Since we're returning a s64, instead of getting the
same negative number we desire, we get a very large positive number.
This handles the case where v < vb->num_pages and ensures we get a small,
negative, s64 as the result.
Rusty: please push this for 2.6.27-rc4. It's probably appropriate for the
stable tree too as it will cause an unexpected OOM when ballooning.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (simplified)
The Extended Interrupt descriptor has a producer/consumer bit, but
it's not clear what that would mean, and existing BIOSes use the bit
inconsistently. This patch makes Linux PNPACPI ignore the bit.
The ACPI spec contains examples of PCI Interrupt Link devices marked
as ResourceProducers, but many BIOSes mark them as ResourceConsumers.
I also checked with a Windows contact, who said:
Windows uses only "resource consumer" when dealing with
interrupts. There's no useful way of looking at a resource
producer of interrupts.
... NT-based Windows largely infers the producer/consumer stuff
from the device type and ignores the bits in the namespace. This
was necessary because Windows 98 ignored them and early namespaces
contained random junk.
The reason I want to change this is because if PNPACPI devices exclude
ResourceProducer IRQ resources, we can't write PNP drivers for those
devices.
For example, on machines such as the the HP rx7620, rx7640, rx8620,
rx8640, and Superdome, HPET interrupts are ResourceProducers. The
HPET driver currently has to use acpi_bus_register_driver() and do its
own _CRS parsing, even though it requires absolutely no ACPI-specific
functionality.
It would be better if the HPET driver were a PNP driver and took
advantage of the _CRS parsing built into PNPACPI.
This producer/consumer check was originally added here:
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commitdiff;h=2b8de5f50e4a302b83ebcd5b0120621336d50bd6
to fix this bug:
http://bugzilla.kernel.org/show_bug.cgi?id=6292
However, the bug was related only to memory and I/O port resources,
where the distinction is sensible and important to Linux. Given that
the distinction is muddled for IRQ resources, I think it was a mistake
to add the check there.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
There is a problem with debugging the X server and gdb crashes in
the xkb startup code.
This avoids the problem by allowing the master process to get signals.
It should be safe as the signal blocker is mainly so that you can
Ctrl-Z a 3D application without locking up the whole box. Ctrl-Z the
X server isn't something many people do.
Signed-off-by: Dave Airlie <airlied@redhat.com>
If a specific tasklet shares data with irq context,
it needs to take a private irq-blocking spinlock within
the tasklet itself.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This makes our handling of cliprects sane. drm_clip_rect always has exclusiv
bottom-right corners, but the hardware expects inclusive bottom-right corner
so we adjust this here.
This complements Michel Daenzer's commit 57aea290e1e0a26d1e74df6cff777eb9f03
to Mesa. See also http://bugs.freedesktop.org/show_bug.cgi?id=16123
Signed-off-by: Dave Airlie <airlied@redhat.com>
DRAW_INDEX writes a vertex count to VAP_VF_CNTL. Docs say that behaviour
is undefined (i.e. lockups happen) when this write is not followed by the
right number of vertex indices.
Thus we used to do the wrong thing when drawing across many cliprects was
necessary, because we emitted a sequence
DRAW_INDEX, DRAW_INDEX, INDX_BUFFER, INDX_BUFFER
instead of
DRAW_INDEX, INDX_BUFFER, DRAW_INDEX, INDX_BUFFER
The latter is what we're doing now and which ought to be correct.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch should fix hard lockup and convert them in
softlockup (ie you can ssh the box but the gpu is busted
and we are waiting in loop for it to come back to reason).
Signed-off-by: Dave Airlie <airlied@redhat.com>
The acer_wmi driver does a DMI scan for quirks, and then sets flags into the
"interface" datastructure for some cases. However, the quirks happen real early
before "interface" is per se initialized from NULL.
The patch below 1) adds a NULL pointer check and 2) (re)runs the quirks at the
end, when "interface" has it's final value.
Reported-by: kerneloops.org
Acked-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
CC: stable@vger.kernel.org
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The mv643xx_eth hardware ignores the lower three bits of the buffer
size field in receive descriptors, causing the reception of full-sized
packets to fail at some MTUs. Fix this by rounding the size of
allocated receive buffers up to a multiple of eight bytes.
While we are at it, add a bit of extra space to each receive buffer so
that we can handle multiple vlan tags on ingress.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
When we are low on memory, the assumption that every descriptor in the
receive ring will have an skbuff associated with it does not hold.
rxq_process() was assuming that if the receive descriptor it is working
on is not owned by the hardware, it can safely be processed and handed
to the networking stack. But a descriptor in the receive ring not being
owned by the hardware can also happen when we are low on memory and did
not manage to refill the receive ring fully.
This patch changes rxq_process()'s bailout condition from "the first
receive descriptor to be processed is owned by the hardware" to "the
first receive descriptor to be processed is owned by the hardware OR
the number of valid receive descriptors in the ring is zero".
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Nicolas Pitre noted that mv643xx_eth_poll was incorrectly using
non-IRQ-safe locks while checking whether to wake up the netdevice's
transmit queue. Convert the locking to *_irq() variants, since we
are running from softirq context where interrupts are enabled.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Commit 12e4ab79cd ("mv643xx_eth: be
more agressive about RX refill") changed the condition for the receive
out-of-memory timer to be scheduled from "the receive ring is empty"
to "the receive ring is not full".
This can lead to a situation where the receive out-of-memory timer is
pending because a previous rxq_refill() didn't manage to refill the
receive ring entirely as a result of being out of memory, and
rxq_refill() is then called again as a side effect of a packet receive
interrupt, and that rxq_refill() call then again does not succeed to
refill the entire receive ring with fresh empty skbuffs because we are
still out of memory, and then tries to call add_timer() on the already
scheduled out-of-memory timer.
This patch fixes this issue by changing the add_timer() call in
rxq_refill() to a mod_timer() call. If the OOM timer was not already
scheduled, this will behave as before, whereas if it was already
scheduled, this patch will push back its firing time a bit, which is
safe because we've (unsuccessfully) attempted to refill the receive
ring just before we do this.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
When a receive interrupt occurs, mv643xx_eth would first process the
receive descriptors and then ACK the receive interrupt, instead of the
other way round.
This would leave a small race window between processing the last
receive descriptor and clearing the receive interrupt status in which
a new packet could come in, which would then 'rot' in the receive
ring until the next receive interrupt would come in.
Fix this by ACKing (clearing) the receive interrupt condition before
processing the receive descriptors.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
This patch lets the files using linux/version.h match the files that
#include it.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] pata_it821x: fix warning
libata: Fix a large collection of DMA mode mismatches
ahci: sis controllers actually can do PMP
pata_via: clean up recent tf_load changes
libata: restore SControl on detach
libata: use ata_link_printk() when printing SError
libata: always do follow-up SRST if hardreset returned -EAGAIN
libata: fix EH action overwriting in ata_eh_reset()
sata_mv: add the Gen IIE flag to the SoC devices.
ata_piix: IDE Mode SATA patch for Intel Ibex Peak DeviceIDs
ahci: RAID mode SATA patch for Intel Ibex Peak DeviceIDs
sata_mv: don't issue two DMA commands concurrently
libata: implement no[hs]rst force params
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IPoIB: Fix deadlock on RTNL in ipoib_stop()
IB/ipath: Fix incorrect check for max physical address in TID
IB/ipath: Fix lost UD send work request
Reported by Andrew Morton:
drivers/ata/pata_it821x.c: In function 'it821x_port_start':
drivers/ata/pata_it821x.c:609: warning: 'mtype' may be used uninitialized in
this function
Pretty horrid fix, but so's a warning..
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Dave Müller sent a diff for the pata_oldpiix that highlighted a problem
where a lot of the ATA drivers assume dma_mode == 0 means "no DMA" while
the core code uses 0xFF.
This turns out to have other consequences such as code doing >= XFER_UDMA_0
also catching 0xFF as UDMAlots. Fortunately it doesn't generally affect
set_dma_mode, although some drivers call back into their own set mode code
from other points.
Having been through the drivers I've added helpers for using_udma/using_mwdma
dma_enabled so that people don't open code ranges that may change (eg if UDMA8
appears somewhere)
Thanks to David for the initial bits
[and added fix for pata_oldpiix from and signed-off-by Dave Mueller
<dave.mueller@gmx.ch> -jg]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
SIS controllers were blacklisted for PMP as enabling it made device
detection fail whether the device was PMP or not - the natural
conclusion was the controller chokes on SRST w/ pmp==15. However, it
turned out that the controller just didn't like issuing SRST after
hardreset w/o clearing SError first. Interestingly, the SRST itself
succeeds but the following commands fail.
If SError is cleared between hardreset and SRST, which is the default
behavior now, everything works fine and SIS controllers work with PMPs
happily.
Remove PMP blacklisting for SIS AHCIs.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Piter PUNK <piterpunk@slackware.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit bfce5e0179 implemented custom
tf_load for pata_via. This patch cleans it up a bit.
* Instead of duplicating whole body, copy tf and set ATA_TFLAG_DEVICE
when necessary.
* Rename via_ata_tf_load() to via_tf_load().
* No need to set .tf_load in via_port_ops_noirq as it inherits from
via_port_ops.
* Clean up indentation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Joseph Chan <JosephChan@via.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Save SControl during probing and restore it on detach. This prevents
adjustments made by libata drivers to seep into the next driver which
gets attached (be it a libata one or not).
It's not clear whether SControl also needs to be restored on suspend.
The next system to have control (ACPI or kexec'd kernel) would
probably like to see the original SControl value but there's no
guarantee that a link is gonna keep working after SControl is adjusted
without a reset and adding a reset and modified recovery cycle soley
for this is an overkill. For now, do it only for detach.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
SError belongs to link not port. Use ata_link_printk() to print it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
As an optimization, follow-up SRST used to be skipped if
classification wasn't requested even when hardreset requested it via
-EAGAIN. However, some hardresets can't wait for device readiness and
skipping SRST can cause timeout or other failures during revalidation.
Always perform follow-up SRST if hardreset returns -EAGAIN. This
makes reset paths more predictable and thus less error-prone.
While at it, move hardreset error checking such that it's done right
after hardreset is finished. This simplifies followup SRST condition
check a bit and makes the reset path easier to modify.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ehc->i.action got accidentally overwritten to ATA_EH_HARD/SOFTRESET in
ata_eh_reset(). The original intention was to clear reset action
which wasn't selected. This can cause unexpected behavior when other
EH actions are scheduled together with reset. Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The SoC sata port is based on the 7042/6042 devices (Gen IIE). This patch
will fix various issues when working with PMP and/or NCQ.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds the Intel Ibex Peak (PCH) IDE mode SATA Controller DeviceIDs.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Resend with proper whitespace.
This patch adds the Intel Ibex Peak (PCH) SATA RAID Controller DeviceIDs.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
sata_mv allowed issuing two DMA commands concurrently which the
hardware allows. Unfortunately, libata core layer isn't ready for
this yet and spews ugly warning message and malfunctions on this.
Don't allow concurrent DMA commands for now.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Implement force params nohrst, nosrst and norst. This is to work
around reset related problems and ease debugging.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Alex Chiang and Matthew Wilcox pointed out that pci_get_dev_by_id() does
not properly decrement the reference on the from pointer if it is
present, like the documentation for the function states it will.
It fixes a pretty bad leak in the hotplug core (we were leaking an
entire struct pci_dev for each function of each offlined card, the first
time around; subsequent onlines/offlines were ok).
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: stable <stable@kernel.org>
Tested-by: Alex Chiang <achiang@hp.com>
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Commit ef0ff95f13 (shpchp: fix slot name)
introduces the shpchp_slot_with_bus module parameter, which was intended
to help work around broken firmware that assigns the same name to multiple
slots.
Commit b3bd307c62 (shpchp: add message about
shpchp_slot_with_bus option) tells the user to use the above parameter
in the event of a name collision.
This approach is sub-optimal because it requires too much work from
the user.
Instead, let's rename the slot on behalf of the user. If firmware
assigns the name N to multiple slots, then:
The first registered slot is assigned N
The second registered slot is assigned N-1
The third registered slot is assigned N-2
The Mth registered slot becomes N-M
In the event we overflow the slot->name parameter, we report an
error to the user.
This is a temporary fix until the entire PCI core can be reworked
such that individual drivers no longer have to manage their own
slot names.
Tested-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Commit 3800345f72 (pciehp: fix slot name)
introduces the pciehp_slot_with_bus module parameter, which was intended
to help work around broken firmware that assigns the same name to multiple
slots.
Commit 9e4f2e8d4d (pciehp: add message about
pciehp_slot_with_bus option) tells the user to use the above parameter
in the event of a name collision.
This approach is sub-optimal because it requires too much work from
the user.
Instead, let's rename the slot on behalf of the user. If firmware
assigns the name N to multiple slots, then:
The first registered slot is assigned N
The second registered slot is assigned N-1
The third registered slot is assigned N-2
The Mth registered slot becomes N-M
In the event we overflow the slot->name parameter, we report an
error to the user.
This is a temporary fix until the entire PCI core can be reworked
such that individual drivers no longer have to manage their own
slot names.
Tested-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
pnp: fix "add acpi:* modalias entries"
UIO: generic irq handling for some uio platform devices
UIO: uio_pdrv: fix license specification
UIO: uio_pdrv: fix memory leak
block: drop references taken by class_find_device()
block: fix partial read() of /proc/{partitions,diskstats}
PM: Remove WARN_ON from device_pm_add
driver core: add init_name to struct device
PM: don't skip device PM init when CONFIG_PM_SLEEP isn't set and CONFIG_PM is set
driver model: anti-oopsing medicine
dev_printk(): constify the `dev' argument
drivers/base/driver.c: remove unused to_dev() macro
Documentation: HOWTO-ja_JP-sync patch
Japanese translation of Documentation/SubmitChecklist
kobject: Replace ALL occurrences of '/' with '!' instead of only the first one.
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: sisusbvga: add USB ID for 0711:0918 Magic Control Technology Corp.
USB: automatically enable RHSC interrupts
USB: Don't rebind before "complete" callback
USB: Add new PM callback methods for USB
USB: Defer Set-Interface for suspended devices
USB: Add udev argument to interface suspend/resume functions
USB: cdc-acm: don't unlock acm->mutex on error path
MUSB: Fix index register corruption seen with g_ether and Windows host
usb: musb: get rid of MUSB_LOGLEVEL and use parameter
usb: musb: get rid of procfs entry
USB: Fix pxa27x_udc usb speed handling.
USB: cdc-acm: quirk for Conexant CX93010 USB modem
USB: fix bug in usb_unlink_anchored_urbs()
usb-serial: option support HSDPA modem A2502
USB: ISP1760: fixed trivial math in comment
Concurrently adding the same segment may lead to duplicate device_register()
calls, which will trigger an error in kobject code:
"... don't try to register things with the same name in the same directory".
This patch adds a check to avoid this.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Calling a ccw driver's notify function without the ccw device lock
held opens up a race window between discovery and handling of a change
in the device operational state. As a result, the device driver may
encounter unexpected device malfunction, leading to out-of-retry
situations or similar.
Remove race by extending the ccw device lock from state change
discovery to the calling of the notify function.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The Perform Subsystem Function/Prepare for Read Subsystem Data
command requires 12 bytes of parameter data, but the respective data
structure dasd_psf_prssd_data has a length of 16 bytes.
Current storage servers ignore the obsolete bytes, but older models
fail to execute the command and report an incorrect length error.
This causes the device initilization for these devices to fail.
To fix this problem we need to correct the dasd_psf_prssd_data
structure and shorten it to the correct length.
Reported-by: Ivan Warren <ivan@vmfacility.fr>
Reviewed-by: Ivan Warren <ivan@vmfacility.fr>
Tested-by: Ivan Warren <ivan@vmfacility.fr>
CC: stable <stable@kernel.org>
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Fix ccw group device initialization: initialize device object before
using reference counting during cleanup.
Fixes the following message when group device initialization fails
(e.g. because too few devices where specified):
kobject: '<NULL>' (..): is not initialized, yet kobject_put() is
being called.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Increasing the qdio reference count for every used subchannel
is unnecessary since unloading qdio (if build as a module) is
only possible if other modules that use qdio are unloaded.
Unloading modules that use qdio in turn requires that these
modules shut down all qdio subchannels. Therefore the additional
module_get reference is not needed.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Improve s390 debug feature usage:
- log busy bit in dbf
- increase size of dbf views
- consistent logging of qdio api calls to setup view
- print subchannel number so one can associate the interface
with the dbf data
- only log events to one view
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If qdio_establish fails we call qdio_shutdown to cleanup the
qdio subchannel. The tiq_list entry may not be valid at that
time, therefore we must ignore queues with an invalid list entry
in tiqdio_remove_input_queues.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In case of error, functions dasd_kmalloc_request and idal_buffer_alloc
return an ERR pointer, but never return the NULL pointer. So after a
call to one of these functions, a NULL test should be replaced by an
IS_ERR test.
A simplified version of the semantic patch that makes this change is
as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@correct_null_test@
expression x,E;
statement S1, S2;
@@
x =
(
dasd_kmalloc_request(...)
|
idal_buffer_alloc(...)
)
<... when != x = E
if (
(
- x@p2 != NULL
+ ! IS_ERR ( x )
|
- x@p2 == NULL
+ IS_ERR( x )
)
)
S1
else S2
...>
? x = E;
// </smpl>
Signed-off-by: Julien Brunel <brunel@diku.dk>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
sisusbvga: add USB ID for 0711:0918 Magic Control Technology Corp.
usb 1-2: new high speed USB device using ehci_hcd and address 4
usb 1-2: configuration #1 chosen from 1 choice
usb 1-2: USB2VGA dongle found at address 4
usb 1-2: Allocated 8 output buffers
usb 1-2: 8MB 1 ch/1 r SDR SDRAM, bus width 32
usb 1-2: New USB device found, idVendor=0711, idProduct=0918
usb 1-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
Signed-off-by: Stefan Lippers-Hollmann <s.L-H@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1069c) changes the way OHCI root-hub status-change
interrupts are enabled. Currently a special HCD method,
hub_irq_enable(), is called when the hub driver is finished using a
root hub. This approach turns out to be subject to races, resulting
in unnecessary polling.
The patch does away with the method entirely. Instead, the driver
automatically enables the RHSC interrupt when no more status changes
are present. This scheme is safe with controllers using
level-triggered semantics for their interrupt flags.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1130) fixes an incompatibility between the new PM
infrastructure and USB power management. We are not allowed to call
drivers' probe routines during a system sleep transition between the
"prepare" and "complete" callbacks, but that's exactly what we do when
a driver doesn't have full suspend/resume support. Such drivers are
unbound during the "suspend" call and reprobed during the "resume" call.
The patch causes the reprobe step to be skipped if the "complete"
callback hasn't been issued yet, i.e., if the interface's
dev.power.status field is not equal to DPM_ON. Thus during the
"resume" callback nothing bad will happen, and during the final
"complete" callback the reprobing will occur as desired.
This fixes the problem reported in Bugzilla #11263.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1129) adds support for the new PM callbacks to usbcore.
The new callbacks merely invoke the same old USB power management
routines as the old ones did.
A minor improvement is that the callbacks are present only in the
"USB-device" device_type structure, rather than in the bus_type
structure. This way they will be invoked only for USB devices, not
for USB interfaces. The core USB PM routines automatically handle
suspending and resuming interfaces along with their devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1128) fixes one of the problems related to the new PM
infrastructure. We are not allowed to register new child devices
during the middle of a system sleep transition, but unbinding a USB
driver causes the core to automatically install altsetting 0 and
thereby create new endpoint pseudo-devices.
The patch fixes this problem (and the related problem that installing
altsetting 0 will fail if the device is suspended) by deferring the
Set-Interface call until some later time when it is legal and can
succeed. Possible later times are: when a new driver is being probed
for the interface, and when the interface is being resumed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1127) makes a minor change to the prototypes of the
usb_suspend_interface() and usb_resume_interface() routines. Now the
usb_device structure is passed as an argument, instead of being
computed on-the-fly from the usb_interface argument.
It makes the code look simpler, even if it really isn't much different
from before.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If Indexed Mode register accesses are enabled, the ep0_rxstate()
function calls musb_g_ep0_giveback() before writing to the CSR
register. When control returns to this ep0_rxstate, the index
register contents are over-written. This causes the CSR register
write to fail.
Fixed by writing the correct value into the index register before
writing to the CSR.
This was observed only in ep0_rxstate() with g_ether loaded and
the device connected to a MS Windows host PC. Anticipatively fixed
ep0_txstate() as well.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We can change debugging level on the fly via
/sys/module/musb_hdrc/parameters/debug.
We can also get rid of the LOGLEVEL facility in Kconfig
and rely only in module parameter.
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drivers should not add procfs. The functionality in the old
procfs file will be moved to debugfs.
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The new composite framework revealed a weakness in the
pxa27x_udc driver gadget register function. Instead of
checking if speed asked for was USB_LOW_SPEED upon
usb_gadget_register() to deny service, it checked only
for USB_FULL_SPEED, thus denying service to usb high
speed capable gadgets (like g_ether).
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch gets my Rosewill RNX-56USB USB modem (with Conexant CX93010
chipset) up and running to the point where I can send AT commands and
retrieve caller ID data, which is all I want to do with it.
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Irqs must not accidentally be reenabled.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch support NTT DoCoMo A2502 3G/HSDPA modem on option driver.
It is produced by AnyDATA Corp. and also sold as KT Freetelecom (Korea) ADU 620UW.
It support 3.6Mbps/7.2Mbps hight speed communication.
I have tested A2502 with NTT DoCoMo MoperaU ISP service.
Signed-off-by: Hiroshi Miura <miurahr@nttdata.co.jp>
Signed-off-by: Matthias Urlichs <matthias@urlichs.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is V3 of uio_pdrv_genirq.c, a platform driver for UIO with
generic IRQ handling code. This driver is very similar to the regular
UIO platform driver, but is only suitable for devices that are
connected to the interrupt controller using unique interrupt lines.
The uio_pdrv_genirq driver includes generic interrupt handling code
which disables the serviced interrupt in the interrupt controller
and makes the user space driver responsible for acknowledging the
interrupt in the device and reenabling the interrupt in the interrupt
controller.
Shared interrupts are not supported since the in-kernel interrupt
handler will disable the interrupt line in the interrupt controller,
and in a shared interrupt configuration this will stop other devices
from delivering interrupts.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Thanks to Magnus Damm for pointing that out.
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Cc: Magnus Damm <magnus.damm@gmail.com>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Thanks to Magnus Damm for pointing that out.
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Cc: Magnus Damm <magnus.damm@gmail.com>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PM: Remove WARN_ON from device_pm_add
Fix message in device_pm_add() saying that the device will not be
added to dpm_list, although in fact the device is going to be added
to the list regardless of the ordering violation.
Remove the WARN_ON(true) triggered in that situation, because it is
hit by USB very often and spams the users' logs.
This patch fixes bug #11263
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This gives us a way to handle both the bus_id and init_name values being
used for a while during the transition period.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1124) fixes a couple of bugs in the PM core. The new
dev->power.status field should be initialized regardless of whether
CONFIG_PM_SLEEP is enabled, and similarly dpm_sysfs_add() should be
called whenever CONFIG_PM is enabled.
The patch separates out the call to dpm_sysfs_add() from the call to
device_pm_add(). As a result device_pm_add() can no longer return an
error, so its return type is changed to void.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Romit Dasgupta <romit@ti.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Anti-oops medicine for the class iterators ... the oops was
observed when a class was implicitly referenced before it
was initialized.
[Modified by Greg to spit a warning back so someone knows to fix their code]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add const markings to dev_name and dev_driver_string to make it clear that
dev_printk doesn't modify dev. This is a prerequisite to adding more
const markings to other functions make it clearer, which functions can
modify dev and which can't.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
