This patch adds support for Power/Status LED on Creative USB X-Fi S51.
There is just one LED on the device. The LED can either be On or it
can be set to Blink. There doesn't seem to be a way to switch it off.
The control message to change LED status is similar to that of
audigy2nx except that the index is to be set to 0 and value is 1 for
Blink and 0 for On.
The 'Power LED' control in alsamixer when muted will cause the LED to
Blink continuously. When unmuted the LED will stay On. The Creative
driver under Windows sets the LED to blink whenever audio is muted.
This LED can be treated as the CMSS LED but I figured since there is
just one LED, it should be treated as the Power LED. Is that alright?
I've also changed the comment "Usb X-Fi" to "Usb X-Fi S51" as there
are other external X-Fi devices from Creative like Usb X-Fi Go and
Xmod. The volume knob and LED support patch doesn't apply to them.
Signed-off-by: Mandar Joshi <emailmandar@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sound/usb/pcm.c::snd_usb_pcm_check_knot() fails to check the return value
from kmalloc() and may end up dereferencing a null pointer.
The patch below (compile tested only) should take care of that little
problem.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are two USB Audio Class specifications (v1 and v2), but neither of
them clearly defines the feedback format for high-speed UAC v1 devices.
Add to this whatever the Creative and M-Audio firmware writers have been
smoking, and it becomes impossible to predict the exact feedback format
used by a particular device.
Therefore, automatically detect the feedback format by looking at the
magnitude of the first received feedback value.
Also, this allows us to get rid of some special cases for E-Mu devices.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adds an entry for Creative USB X-Fi to the rc_config array in
mixer_quirks.c to allow use of volume knob on the device.
The action of the volume knob is received by lirc when its using the
alsa_usb driver.
Signed-off-by: Mandar Joshi <emailmandar@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a quirk entry for the Novation Launchpad USB MIDI controller.
QUIRK_MIDI_FASTLANE gets renamed to *_RAW_BYTES because this quirk type
is now shared by different devices.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Tested-by: Jakob Flierl <jakob.flierl@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add quirks for more devices (according to driver V.3.0.4-2).
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
"uinfo->value.enumerated.item" is an unsigned int. If it's negative
when we do the comparison:
if ((int)uinfo->value.enumerated.item >= cval->max)
then we would read past the end of the array on the next line.
I also changed the strcpy() to strlcpy() out of paranoia.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Used only when CONFIG_SND_DEBUG=y
sound/usb/mixer.c: In function 'get_min_max':
sound/usb/mixer.c:762: warning: unused variable 'chip'
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds support for the new Traktor Kontrol S4 by Native
Instruments. It features a new audio data streaming model, MIDI
in and out ports, a huge number of 174 dimmable LEDs, 96 buttons
and 46 absolute encoder axis, including some rotary encoders.
All features are supported by the driver now.
Did some code refactoring along the way.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Due to the wrong "return" in the loop, a capture substream won't be
released at disconnection properly if the device is capture only and has
no playback substream. This caused Oops occasionally at the device
reconnection.
Reported-by: Kim Minhyoung <minhyoung.kim@lge.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Audio Class v2 support code in 2.6.35 added checks for the
bInterfaceProtocol field. However, there are devices (usually those
detected by vendor-specific quirks) that do not have one of the
predefined values in this field, which made the driver reject them.
To fix this regression, restore the old behaviour, i.e., assume that
a device with an unknown bInterfaceProtocol field (other than
UAC_VERSION_2) has more or less UAC-v1-compatible descriptors.
[compile warning fixes by tiwai]
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a quirk to make the BOSS ME-25 work.
Many thanks to Kees van Veen.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a quirk for the Roland/Cakewalk A-300PRO/A-500PRO/A-800PRO keyboards.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a quirk for the other logical device of the PCR-1 so that not only
the MIDI interface but also the audio interface works.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For devices with more than one control interface, let's assume the first
one contains the audio controls. Unfortunately, there is no field in any
of the descriptors to tell us whether a control interface is for audio
or MIDI controls, so a better check is not easy to implement.
On a composite device with audio and MIDI functions, for example, the
code currently overwrites chip->ctrl_intf, causing operations on the
control interface to fail if they are issued after the device probe.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The M-Audio Fast Track Ultra series devices did not play sound correctly
at 44.1/88.2 kHz. Changing the output endpoint attribute to adaptive
fixes this.
Signed-off-by: Felix Homann <fexpop@web.de>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: sound/usb/format: silence uninitialized variable warnings
MAINTAINERS: Add Ian Lartey as comaintaner for Wolfson devices
MAINTAINERS: Make Wolfson entry also cover CODEC drivers
ASoC: Only tweak WM8994 chip configuration on devices up to rev D
ASoC: Optimise DSP performance for WM8994
ALSA: hda - Fix dynamic ADC change working again
ALSA: hda - Restrict PCM parameters per ELD information over HDMI
sound: oss: sh_dac_audio.c removed duplicated #include
Gcc complains that ret might be used uninitialized:
sound/usb/format.c: In function ‘snd_usb_parse_audio_format’:
sound/usb/format.c:354: warning: ‘ret’ may be used uninitialized in this function
sound/usb/format.c:354: note: ‘ret’ was declared here
sound/usb/format.c:414: warning: ‘ret’ may be used uninitialized in this function
sound/usb/format.c:414: note: ‘ret’ was declared here
I suppose it could be uninitialized if there is ever a UAC_VERSION_3
released. Anyway this patch is worthwhile if only to silence the gcc
warning.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is V2 of the patch, after feedback from Clemens and Daniel.
This patch adds SuperSpeed support to the USB drivers under sound/. It adds
tests for USB_SPEED_SUPER to the appropriate places that check for the USB
speed.
This patch has been tested with our SS USB3 device emulating a set of Yamaha
speakers and a Logitech microphone, but with the descriptors modified to add
USB3 support. It has also been tested with the real speakers and microphone,
to make sure that USB2 devices still work.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Cc: Clemens Ladisch <clemens@ladisch.de>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (214 commits)
ALSA: hda - Add pin-fix for HP dc5750
ALSA: als4000: Fix potentially invalid DMA mode setup
ALSA: als4000: enable burst mode
ALSA: hda - Fix initial capsrc selection in patch_alc269()
ASoC: TWL4030: Capture route runtime DAPM ordering fix
ALSA: hda - Add PC-beep whitelist for an Intel board
ALSA: hda - More relax for pending period handling
ALSA: hda - Define AC_FMT_* constants
ALSA: hda - Fix beep frequency on IDT 92HD73xx and 92HD71Bxx codecs
ALSA: hda - Add support for HDMI HBR passthrough
ALSA: hda - Set Stream Type in Stream Format according to AES0
ALSA: hda - Fix Thinkpad X300 so SPDIF is not exposed
ALSA: hda - FIX to not expose SPDIF on Thinkpad X301, since it does not have the ability to use SPDIF
ASoC: wm9081: fix resource reclaim in wm9081_register error path
ASoC: wm8978: fix a memory leak if a wm8978_register fail
ASoC: wm8974: fix a memory leak if another WM8974 is registered
ASoC: wm8961: fix resource reclaim in wm8961_register error path
ASoC: wm8955: fix resource reclaim in wm8955_register error path
ASoC: wm8940: fix a memory leak if wm8940_register return error
ASoC: wm8904: fix resource reclaim in wm8904_register error path
...
Match usb ids in usb/quirks-table.h for some Hauppage HVR-950Q models
and for the HVR850 model to those ids at the end of au0828-cards.c
Thanks to nhJm449 for pointing out the problem.
Signed-off-by: John S Gruber <JohnSGruber@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It is not advisable to print a warning when a device does not support
setting the sample rate because this is perfectly valid for devices with
a single rate or where rates are implicitly changed by selecting another
alternate setting.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As the control interface is now carried in struct snd_usb_audio, we can
simplify the API a little and also drop the private ctrlif field from
struct usb_mixer_interface.
Also remove a left-over function prototype in pcm.h.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Get rid of the last occurances of _v1 suffixes, and move the version
number right after the "uac" string. Now things are consitent again.
Sorry for the forth and back, but it just looks much nicer this way.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some programs like Skype trying to set capture volume automatically.
Normally it will tray, carefully step by step lover or higher, set the volume.
In real word it work not really well, because devises and vendors lie about
real audio settings.
For example most Logitech webcams have 6400 or 3500 steps for capture volume.
They do not tell that actual resolution is 384. So we have only 7 or 18 real
steps. In this patch I set real resolution only for tested devices.
Signed-off-by: Alexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Stanse found that in snd_usb_parse_audio_endpoints, there is a
dangling pointer dereference. When snd_usb_parse_audio_format fails,
fp is freed, and continue invoked. On the next loop, there is
"fp && fp->altsetting == 1 && fp->channels == 1" test, but fp is set
from the last iteration (but is bogus) and thus ilegally dereferenced.
Set fp to NULL before "continue".
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For RANGE requests, we should only query as much bytes as we're in fact
interested in.
For CUR requests, we shouldn't confuse the firmware with an overlong
request but just ask for 2 bytes.
This might need fixing in the future as it's not entirely clear when to
dispatch 1-byte, 2-byte and 4-byte request blocks. For now, we assume
everything is coded in 16bit - this works for all firmware
implementations I've seen.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Reported-by: Alex Lee <alexlee188@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A device may report its supported sample rates in ranges rather than in
discrete triplets. The code used to only parse the MIN field instead of
properly paying attention to the MAX and RES values.
Also, handle RES values of 1 correctly and announce a continous sample
rate range in this case.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Reported-by: Alex Lee <alexlee188@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Control messages directed to an interface must have the interface number
set in the lower 8 bits of wIndex. This wasn't done correctly for some
clock and mixer messages.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Reported-by: Alex Lee <alexlee188@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The UAC2 clock selectors are fortunately compatible with UAC1 audio
selector units, so we can simply reuse the same approach to get all the
linked units.
Requests to this control need a different CS value though.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use a struct to parse the audio units, and return usable descriptors
for all types. There's no need to limit the result set, except for some
kind of sanity check.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The bits to enable them are always 0 for UAC1 devices, so no additional
checks are required.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move more definitions from private enums to appropriate header files.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Audio devices which comply to the UAC2 standard can export complex clock
topologies in its descriptors and set up links between them.
The entities that are defined are
- clock sources, which define the end-leafs.
- clock selectors, which act as switch to select one out of many
possible clocks sources.
- clock multipliers, which have an input clock source, and act as clock
source again. They can be used to derive one clock from another.
All sample rate changes, clock validity queries and the like must go to
clock source elements, while clock selectors and multipliers can be used
as terminal clock source.
The following patch adds a parser for these elements and functions to
iterate over the tree and find the leaf nodes (clock sources).
The samplerate set functions were moved to the new clock.c file.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
So far, UAC2 controls are marked read-only if any of the channels are
marked read-only in the descriptors. Change this behaviour and
- mark them writeable unless all channels are read-only
- store the read-only mask in usb_mixer_elem_info and
- check the mask again in set_cur_mix_value(), and bail out for
write-protected channels.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Introduce two new static inline functions for a more readable parsing
of UAC2 bmaControls.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
