This reverts commit 329cabcecf.
The commit that caused us to specify LE device endianness here,
29bb45f25f (regmap-mmio: Use native endianness for read/write,
2015-10-29), has been reverted in mainline so now when we specify
LE it actively breaks big endian kernels because the byte
swapping in regmap-mmio is incorrect. Let's revert this change
because it will 1) fix the big endian kernels and 2) be redundant
to specify LE because that will become the default soon.
Cc: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add a driver for the multimedia clock controller found on MSM8996
based devices. This should allow most multimedia device drivers
to probe and control their clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The GPU clocks on msm8996 have three dedicated PLLs, MMPLL2,
MMPLL8, and MMPLL9. We leave MMPLL9 at the maximum speed (624
MHz), and we use MMPLL2 and MMPLL8 for the other frequencies. To
make switching frequencies faster, we ping-pong between MMPLL2
and MMPLL8 when we're switching between frequencies that aren't
the maximum. Implement custom rcg clk ops for this type of
frequency switching.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add support for the global clock controller found on MSM8996
based devices. This should allow most non-multimedia device
drivers to probe and control their clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add support for configuring rates of, enabling, and disabling
Alpha PLLs. This is sufficient for the types of PLLs found in
the global and multimedia clock controllers.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Move the xo and sleep clocks to device-tree, instead of hard-coding
them in the driver. This allows us to insert the RPM clocks (if they
are enabled) in between the on-board oscillators and the actual clock.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
All these clock controllers are little endian devices, but so far
we've been relying on the regmap mmio bus handling this for us
without explicitly stating that fact. After commit 4a98da2164cf
(regmap-mmio: Use native endianness for read/write, 2015-10-29),
the regmap mmio bus will read/write with the __raw_*() IO
accessors, instead of using the readl/writel() APIs that do
proper byte swapping for little endian devices.
So if we're running on a big endian processor and haven't
specified the endianness explicitly in the regmap config or in
DT, we're going to switch from doing little endian byte swapping
to big endian accesses without byte swapping, leading to some
confusing results. On my apq8074 dragonboard, this causes the
device to fail to boot as we access the clock controller with
big endian IO accesses even though the device is little endian.
Specify the endianness explicitly so that the regmap core
properly byte swaps the accesses for us.
Reported-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Tyler Baker <tyler.baker@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Cc: Simon Arlott <simon@fire.lp0.eu>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Put these clocks into the dt files instead of registering them
from C code. This provides a few benefits. It allows us to
specify the frequency of these clocks at the board level instead
of hard-coding them in the driver. It allows us to insert an RPM
clock in between the consumers of the crystals and the actual
clock. And finally, it helps us transition the GCC driver to use
RPM clocks when that configuration is enabled.
Cc: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
We want to put the XO board clocks into the dt files, but we also
need to be backwards compatible with an older dtb. Add an API to
the common code to do this. This also makes a place for us to
handle the case when the RPM clock driver is enabled and we don't
want to register the fixed factor clock.
Cc: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The halt bits for these clocks seem wrong. I get the following
warning while booting on an msm8960-cdp:
WARNING: CPU: 0 PID: 1 at drivers/clk/qcom/clk-branch.c:97 clk_branch_toggle+0xd0/0x138()
dsi1_clk status stuck at 'on'
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.3.0-rc3-00113-g5532cfb567fe #110
Hardware name: Qualcomm (Flattened Device Tree)
[<c0216984>] (unwind_backtrace) from [<c02138f8>] (show_stack+0x10/0x14)
[<c02138f8>] (show_stack) from [<c04a525c>] (dump_stack+0x70/0xbc)
[<c04a525c>] (dump_stack) from [<c0223c70>] (warn_slowpath_common+0x78/0xb4)
[<c0223c70>] (warn_slowpath_common) from [<c0223d40>] (warn_slowpath_fmt+0x30/0x40)
[<c0223d40>] (warn_slowpath_fmt) from [<c05fc2dc>] (clk_branch_toggle+0xd0/0x138)
[<c05fc2dc>] (clk_branch_toggle) from [<c05f3f3c>] (clk_disable_unused_subtree+0x98/0x1b0)
[<c05f3f3c>] (clk_disable_unused_subtree) from [<c05f3ec4>] (clk_disable_unused_subtree+0x20/0x1b0)
[<c05f3ec4>] (clk_disable_unused_subtree) from [<c05f5474>] (clk_disable_unused+0x58/0xd8)
[<c05f5474>] (clk_disable_unused) from [<c0209710>] (do_one_initcall+0xac/0x1ec)
[<c0209710>] (do_one_initcall) from [<c0991db4>] (kernel_init_freeable+0x11c/0x1e8)
[<c0991db4>] (kernel_init_freeable) from [<c0727ae0>] (kernel_init+0x8/0xec)
[<c0727ae0>] (kernel_init) from [<c0210238>] (ret_from_fork+0x14/0x3c)
Fix the status bits and the errors go away.
Fixes: 5532cfb567 ("clk: qcom: mmcc-8960: Add DSI related clocks")
Acked-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add rcg and branch clk structs for DSI1 and DSI2 blocks found in MSM8960
and APQ8064. Each DSI instance has 4 pairs of rcg and branch clocks.
Populate arrays mmcc_msm8960_clks and mmcc_apq8064_clks with these clocks.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
DSI specific RCG clocks required customized clk_ops. There are
a total of 4 RCGs per DSI block: DSI, BYTE, ESC and PIXEL.
There are a total of 2 clocks coming from the DSI PLL, which serve as
inputs to these RCGs. The BYTE and ESC RCGs are fed by one of the
post dividers of DSI1 or DSI2 PLLs, and the DSI and PIXEL RCGs are fed by
another divider of the PLL.
In each of the 2 groups above, only one of the clocks sets its parent.
These are BYTE RCG and DSI RCG for each of the groups respectively, as
shown in the diagram below.
The DSI and BYTE RCGs serve as bypass clocks. We create a new set of ops
clk_rcg_bypass2_ops, which are like the regular bypass ops, but don't
take in a freq table, since the DSI driver using these clocks is
parent-able.
The PIXEL RCG needs to derive the required pixel clock using dsixpll.
It parses a m/n frac table to retrieve the correct clock.
The ESC RCG doesn't have a frac M/N block, it can just apply a pre-
divider. Its ops simply check if the required clock rate can be
achieved by the pre-divider.
+-------------------+
| |---dsixpllbyte---o---> To byte RCG
| | | (sets parent rate)
| | |
| | |
| DSI 1/2 PLL | |
| | o---> To esc RCG
| | (doesn't set parent rate)
| |
| |----dsixpll-----o---> To dsi RCG
+-------------------+ | (sets parent rate)
( x = 1, 2 ) |
|
o---> To pixel rcg
(doesn't set parent rate)
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
8960 family of devices have TSENS as part of GCC in hardware.
Hence DT would represent a GCC node with GCC properties as well
as TSENS. Create a virtual platform child device here for TSENS
so the driver can probe it and use the parent (GCC) to extract DT
properties.
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
[sboyd@codeaurora.org: Massaged to work with devm friendly
qcom_cc_probe()]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Having this hidden config below the COMMON_CLK_QCOM config causes
menuconfig to stop indenting config items after it.
<*> Support for Qualcomm's clock controllers
{M} APQ8084 Global Clock Controller
<M> APQ8084 Multimedia Clock Controller
{M} IPQ806x Global Clock Controller
<M> IPQ806x LPASS Clock Controller
<M> MSM8660 Global Clock Controller
<M> MSM8916 Global Clock Controller
{M} APQ8064/MSM8960 Global Clock Controller
<M> APQ8064/MSM8960 LPASS Clock Controller
<M> MSM8960 Multimedia Clock Controller
{M} MSM8974 Global Clock Controller
<M> MSM8974 Multimedia Clock Controller
Move it up above anything else so that we don't get odd
indenting.
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now that qcom_cc_remove() is a nop, drop calls to
qcom_cc_remove() and any empty driver remove functions.
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some APIs in qcom_cc_probe() don't have a devm counterpart, so we
have to use the calling device's platform data to pass pointers
to the remove path. Let's use devm_add_action() instead, so that
the remove path doesn't need to do anything, allowing us to
remove qcom_cc_remove() entirely.
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The oxili_cx GDSC is inside the power domain of the oxili GDSC.
Add the dependency so that the CX domain can properly power up.
Reported-by: Rob Clark <robdclark@gmail.com>
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add support for the msm8916 audio clocks. This includes core bus,
low-power audio and codec clocks. They are required for audio playback.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add support for the msm8916 BIMC (Bus Integrated Memory Controller)
clocks that are needed for GPU.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some root clock generators may have child branches that are controlled
by different CPUs. These RCGs require some special operations:
- some enable bits have to be toggled when we set the rate;
- if RCG is disabled we only cache the rate and set it later when enabled;
- when the RCG is disabled, the mux is set to the safe source;
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
[sboyd@codeaurora.org: Simplify recalc_rate implementation]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add support for the msm8916 TCU (Translation Control Unit) clocks that
are needed for IOMMU.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add the GDSC instances that exist as part of apq8084 MMCC block.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add the GDSC instances that exist as part of apq8084 GCC block
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add the GDSC instances that exist as part of msm8974 MMCC block
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
There's just one GDSC as part of the msm8974 GCC block.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add all data for the GDSCs which are part of msm8916 GCC block.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Certain devices can have GDSCs' which support ON as the only state.
They can't be power collapsed to either hit RET or OFF.
The clients drivers for these GDSCs' however would expect the state
of the core to be reset following a GDSC disable and re-enable.
To do this assert/deassert reset lines every time the client
driver would request the GDSC to be powered on/off instead.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Along with the GDSC power switch, there is additional control
to either retain all memory (core and peripheral) within a given
powerdomain or to turn them off while the GDSC is powered down.
Add support for these by modelling a RET state where all
memory is retained and an OFF state where all memory gets turned
off.
The controls provided are granular enough to be able to support
various differnt levels of RET states, like a 'shallow RET' with all memory
retained and a 'deep RET' with some memory retained while some others
are lost. The current patch does not support this and considers
just one RET state where all memory is retained. Futher work, if
needed can support multiple different levels of RET state.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The common clk probe registers a clk provider and a reset controller.
Update it to register a genpd provider using the gdsc data provided
by each platform.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
GDSCs (Global Distributed Switch Controllers) are responsible for
safely collapsing and restoring power to peripherals in the SoC.
These are best modelled as power domains using genpd and given
the registers are scattered throughout the clock controller register
space, its best to have the support added through the clock driver.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Sometimes the display driver may want to change the parent PLL of
the display clocks (byte and pixel clocks) depending on the
use-case. Currently the parent is fixed by means of having a
frequency table with one entry that chooses a particular parent.
Remove this restriction and use the parent the clock is
configured for in the hardware during clk_set_rate(). This
requires consumers to rely on the default parent or to configure
the parent with clk_set_parent()/assigned-clock-parents on the
clocks before calling clk_set_rate().
Tested-by: Archit Taneja <architt@codeaurora.org>
Cc: Hai Li <hali@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Fix the enable bit of the pseudorandom number generator clock.
Reported-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Fixes: 3966fab8b6 "clk: qcom: Add MSM8916 Global Clock Controller support"
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Use the provider based method to get a clock's name so that we
can get rid of the clk member in struct clk_hw one day. Mostly
converted with the following coccinelle script.
@@
struct clk_hw *E;
@@
-__clk_get_name(E->clk)
+clk_hw_get_name(E)
Acked-by: Heiko Stuebner <heiko@sntech.de>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: Prashant Gaikwad <pgaikwad@nvidia.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kevin Cernekee <cernekee@chromium.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
We're removing struct clk from the clk provider API, so switch
this code to using the clk_hw based provider APIs.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Mostly converted with the following snippet:
@@
struct clk_hw *E;
@@
-__clk_get_flags(E->clk)
+clk_hw_get_flags(E)
Acked-by: Tero Kristo <t-kristo@ti.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The missing license causes the clk-qcom.ko module to taint the
kernel. Add the appropriate license to avoid taint.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
* cleanup-clk-h-includes: (62 commits)
clk: Remove clk.h from clk-provider.h
clk: h8300: Remove clk.h and clkdev.h includes
clk: at91: Include clk.h and slab.h
clk: ti: Switch clk-provider.h include to clk.h
clk: pistachio: Include clk.h
clk: ingenic: Include clk.h
clk: si570: Include clk.h
clk: moxart: Include clk.h
clk: cdce925: Include clk.h
clk: Include clk.h in clk.c
clk: zynq: Include clk.h
clk: ti: Include clk.h
clk: sunxi: Include clk.h and remove unused clkdev.h includes
clk: st: Include clk.h
clk: qcom: Include clk.h
clk: highbank: Include clk.h
clk: bcm: Include clk.h
clk: versatile: Remove clk.h and clkdev.h includes
clk: ux500: Remove clk.h and clkdev.h includes
clk: tegra: Properly include clk.h
...
The other ce clocks have the flag set, but ce1 doesn't, so
clk_set_rate() doesn't propagate up the tree to the ce1_src_clk.
Set the flag as this is supported.
Reported-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Tested-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Fixes: 0282465320 ("clk: qcom: Add APQ8084 Global Clock Controller support")
Fixes: d33faa9ead ("clk: qcom: Add support for MSM8974's global clock controller (GCC)")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Clock rates are stored in an unsigned long field, but ->determine_rate()
(which returns a rounded rate from a requested one) returns a long
value (errors are reported using negative error codes), which can lead
to long overflow if the clock rate exceed 2Ghz.
Change ->determine_rate() prototype to return 0 or an error code, and pass
a pointer to a clk_rate_request structure containing the expected target
rate and the rate constraints imposed by clk users.
The clk_rate_request structure might be extended in the future to contain
other kind of constraints like the rounding policy, the maximum clock
inaccuracy or other things that are not yet supported by the CCF
(power consumption constraints ?).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
CC: Jonathan Corbet <corbet@lwn.net>
CC: Tony Lindgren <tony@atomide.com>
CC: Ralf Baechle <ralf@linux-mips.org>
CC: "Emilio López" <emilio@elopez.com.ar>
CC: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
CC: Peter De Schrijver <pdeschrijver@nvidia.com>
CC: Prashant Gaikwad <pgaikwad@nvidia.com>
CC: Stephen Warren <swarren@wwwdotorg.org>
CC: Thierry Reding <thierry.reding@gmail.com>
CC: Alexandre Courbot <gnurou@gmail.com>
CC: linux-doc@vger.kernel.org
CC: linux-kernel@vger.kernel.org
CC: linux-arm-kernel@lists.infradead.org
CC: linux-omap@vger.kernel.org
CC: linux-mips@linux-mips.org
CC: linux-tegra@vger.kernel.org
[sboyd@codeaurora.org: Fix parent dereference problem in
__clk_determine_rate()]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[sboyd@codeaurora.org: Folded in fix from Heiko for fixed-rate
clocks without parents or a rate determining op]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add support for SR2 type pll operations. SR2 is optimized for Time Interval
Error (TIE) or absolute jitter.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Make const both the array and the strings, so they can be
moved to .rodata section.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Since the parent rate has been recalculated, pixel RCG clock
should rely on it to find the correct M/N values during set_rate,
instead of calling __clk_round_rate() to its parent again.
Signed-off-by: Hai Li <hali@codeaurora.org>
Tested-by: Archit Taneja <architt@codeaurora.org>
Fixes: 99cbd064b0 ("clk: qcom: Support display RCG clocks")
[sboyd@codeaurora.org: Silenced unused parent variable warning]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add the NSS/GMAC clocks and the TCM clock and NSS resets.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The gfx3d_clk_src parents configuration is incorrect. Fix it.
Fixes: 3966fab8b6 "clk: qcom: Add MSM8916 Global Clock Controller support"
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
One of the video codec clock frequencies has incorrect divider
value. Fix it.
Fixes: 3966fab8b6 "clk: qcom: Add MSM8916 Global Clock Controller support"
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
