Commit Graph

496 Commits

Author SHA1 Message Date
Alan Stern
5f47493cdf USB: OHCI: turn off RD when remote wakeup is disabled
This patch (as1068b) disables the RD interrupt flag when an OHCI root
hub is suspended with remote wakeup disabled.  Although the spec
clearly states that this flag permits the controller to issue an
interrupt when a resume request from downstream is detected and not
when a local status change occurs, some controllers mistakenly use it
for both types of event.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-24 21:16:53 -07:00
Alan Stern
58a97ffeb2 USB: HCDs use the do_remote_wakeup flag
When a USB device is suspended, whether or not it is enabled for
remote wakeup depends on the device_may_wakeup() setting.  The setting
is then saved in the do_remote_wakeup flag.

Later on, however, the device_may_wakeup() value can change because of
user activity.  So when testing whether a suspended device is or
should be enabled for remote wakeup, we should always test
do_remote_wakeup instead of device_may_wakeup().  This patch (as1076)
makes that change for root hubs in several places.

The patch also adjusts uhci-hcd so that when an autostopped controller
is suspended, the remote wakeup setting agrees with the value recorded
in the root hub's do_remote_wakeup flag.

And the patch adjusts ehci-hcd so that wakeup events on selectively
suspended ports (i.e., the bus itself isn't suspended) don't turn on
the PME# wakeup signal.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-24 21:16:53 -07:00
David Brownell
a082b5c788 USB: ehci: qh/qtd cleanup comments
Provide better comments about qh_completions() and QTD handling.
That code can be *VERY* confusing, since it's evolved over a few
years to cope with both hardware races and silicon quirks.

Remove two unlikely() annotations that match the GCC defaults
(and are thus pointless); add an "else" to highlight code flow.

This patch doesn't change driver behavior.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-24 21:16:50 -07:00
Yoshihiro Shimoda
9424ea2965 USB: r8a66597-hcd: Add support for SH7366 USB host
R8A66597 is similar to SH7366 USB 2.0 Host/Function module. It can
support SH7366 USB host by changing several R8A66597 code.

Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-24 21:16:49 -07:00
Yoshihiro Shimoda
29fab0cd89 USB: r8a66597-hcd: fix usb device connection timing
Fix the problem that enumeration of a USB device was slow.

Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-24 21:16:49 -07:00
Yoshihiro Shimoda
6d8791076c USB: r8a66597-hcd: fix interrupt transfer interval
This driver ignored the value of bInterval and revised the problem
that performed interrupt transfer.

ASIX USB Ethernet adapter comes to work with this host controller
by applying this patch.

Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-24 21:16:49 -07:00
Sarah Sharp
21da84a893 USB: ehci shutdown refactored
This patch refactors some shutdown code so it can be shared between
ehci_stop() and ehci_shutdown().

This also fixes a couple potential bugs:
 - ehci_shutdown() was not locking ehci->lock before halting the HC.
 - ehci_shutdown() didn't disable the watchdog and IAA timers.
 - ehci_stop() was resetting the host controller when it may have been
   running, which the EHCI spec says "may result in undefined behavior".

ehci_stop() was calling port_power() to turn off the ports, which waited
20ms after applying the port change.  The msleep was for the case where
the HC might take 20ms to turn the ports on; since we're shutting them
off, we can avoid the msleep and just use ehci_turn_off_ports().

ehci_stop() doesn't need to clear the intr_enable register or revert
ownership of the companion controllers to the BIOS, because the host
controller reset should have done that.  There might be a buggy host
controller that doesn't follow the reset rules, but for now we assume
it's redundant code and remove it.

[ A subsequent patch will cancel the timers later ... this version
carries forward existing bugs where timers could get re-armed
after they're canceled. ]

Signed-off-by: Sarah Sharp <sarah.a.sharp@intel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-24 21:16:49 -07:00
Alan Stern
43bbb7e015 USB: OHCI: host-controller resumes leave root hub suspended
Drivers in the ohci-hcd family should perform certain tasks whenever
their controller device is resumed.  These include checking for loss
of power during suspend, turning on port power, and enabling interrupt
requests.

Until now these jobs have been carried out when the root hub is
resumed, not when the controller is.  Many drivers work around the
resulting awkwardness by automatically resuming their root hub
whenever the controller is resumed.  But this is wasteful and
unnecessary.

To simplify the situation, this patch (as1066) adds a new core
routine, ohci_finish_controller_resume(), which can be used by all the
OHCI-variant drivers.  They can call the new routine instead of
resuming their root hubs.  And ohci-pci.c can call it instead of using
its own special-purpose handler.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-24 21:16:48 -07:00
Alan Stern
7be7d74187 USB: clarify usage of hcd->suspend/resume methods
The .suspend and .resume method pointers in struct usb_hcd have not
been fully understood by host-controller driver writers.  They are
meant for use with PCI controllers; other platform-specific drivers
generally should not refer to them.

To try and clarify matters, this patch (as1065) renames those methods
to .pci_suspend and .pci_resume.  It eliminates corresponding dead code
and bogus references in the ohci-ssb and u132-hcd drivers.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-24 21:16:48 -07:00
Alan Stern
7329e211b9 USB: root hubs don't lie about their number of TTs
Currently EHCI root hubs enumerate with a bDeviceProtocol code
indicating that they possess a Transaction Translator.  However the
vast majority of controllers do not; they rely on a companion
controller to handle full- and low-speed communications.  This patch
(as1064) changes the root-hub device descriptor to match the actual
situation.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-24 21:16:48 -07:00
Alan Stern
0d22f65515 USB: OHCI: fix bug in controller resume
This patch (as1063) fixes a bug in the way ohci-hcd resumes its
controllers.  It leaves the Master Interrupt Enable bit turned off.

If the root hub is resumed immediately this won't matter.  But if the
root hub is suspended (say because no devices are plugged in), it won't
ever wake up by itself.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-24 21:16:47 -07:00
Jesper Juhl
119fc8c9ac USB: test for NULL return from platform_get_resource() in ohci_hcd_sm501_drv_remove()
platform_get_resource() may return null, so although it seems it will never
do so here unless there's a bug elsewhere, it does no harm to be defensive
and test.

Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-24 21:16:45 -07:00
Daniel Walker
50d8ca9b56 usb: u132-hcd driver: semaphore to mutex
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-24 21:16:45 -07:00
Daniel Walker
b40f8d3980 usb: u132-hcd driver style clean up
I was converting a semaphore in this file to a mutex when I noticed that
this file has some fairly rampant style problems. Practically every line
has spaces instead of tabs .. Once I cleared that up, checkpatch.pl showed
a number of other problem.. I think this file might be a good one to review
for new style checks that could be added..

Below are the only two remaining which I didn't remove. 

#5083: FILE: drivers/usb/host/u132-hcd.c:2907:
+               error:

WARNING: labels should not be indented
#5087: FILE: drivers/usb/host/u132-hcd.c:2911:
+               stall:

These labels are actually inside a switch statement, and they are right
under "default:". "default:" appears to be exempt and these other label
should be too, or default shouldn't be exempt.

I also deleted a few lines due to single statements inside { } , 

if (is_error()) {
	return;
}

becomes,

if (is_error())
	return;

with one line deleted.

Signed-off-by: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-24 21:16:44 -07:00
Robert P. J. Day
9ec249a658 USB: Remove EXPERIMENTAL designation from USB_EHCI_ROOT_HUB_TT.
According to David Brownell, this feature doesn't require an
experimental designation any longer.

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-24 21:16:43 -07:00
David Brownell
25b70a8665 USB: ehci: paranoia, reject large control transfers
Some EHCI fault paths with large control transfers aren't coded.  Avoid
problems by rejecting transfers that may need two qTDs (16+ KB).  This is
mostly paranoia; even 4 KB transfers are rare, and most HCDs use lower
limits (so it's unlikely anyone would ever try such a thing).

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-24 21:16:41 -07:00
Alan Stern
70a1c9e086 USB: remove dev->power.power_state
power.power_state is scheduled for removal.  This patch (as1053)
removes all uses of that field from drivers/usb.  Almost all of them
were write-only, the most significant exceptions being sl811-hcd.c and
u132-hcd.c.

Part of this patch was written by Pavel Machek.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-24 21:16:41 -07:00
David Brownell
d1b1842c39 USB: ehci: remove obsolete workaround for bogus IRQs
It was pointed out that we found and fixed the cause of the "bogus"
fatal IRQ reports some time ago ... this patch removes the code
which was working around that bug ("status" got clobbered), and a
comment which needlessly confused folk reading this code.

This also includes a minor cleanup to the code which fixed that bug.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-24 21:16:40 -07:00
Julia Lawall
dfa5ec79d2 USB: use DIV_ROUND_UP
The kernel.h macro DIV_ROUND_UP performs the computation (((n) + (d) - 1) /
(d)) but is perhaps more readable.

An extract of the semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@haskernel@
@@

#include <linux/kernel.h>

@depends on haskernel@
expression n,d;
@@

(
- (n + d - 1) / d
+ DIV_ROUND_UP(n,d)
|
- (n + (d - 1)) / d
+ DIV_ROUND_UP(n,d)
)

@depends on haskernel@
expression n,d;
@@

- DIV_ROUND_UP((n),d)
+ DIV_ROUND_UP(n,d)

@depends on haskernel@
expression n,d;
@@

- DIV_ROUND_UP(n,(d))
+ DIV_ROUND_UP(n,d)
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-24 21:16:39 -07:00
Karsten Wiese
3d01f0fe6b USB: minor ehci xITD simplifications
Remove two (or one) conditional tests in per-urb isochronous
transfer setup code paths.

Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-24 21:16:38 -07:00
Karsten Wiese
c765d4cad9 USB: EHCI: Refactor "if (handshake()) state = HC_STATE_HALT"
Refactor the EHCI "if (handshake()) state = HC_STATE_HALT" idiom,
which appears 4 times, by replacing it with calls to a new function
called handshake_on_error_set_halt().  Saves a few bytes too.

Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-24 21:16:35 -07:00
David Brownell
135db0485c USB: ehci minor SOC bus glue fixes
Various minor fixes to some SOC bus glue for EHCI:

 - Remove a bogus copyright (by "me"!) which someone added to the FSL
   driver, and an irrelevant comment.

 - Un-break MODULE_ALIAS() directives after platform_bus hotplugging
   acquired a backwards-incompatible change.  (Which didn't fix ANY
   of the in-tree drivers it prevented from hotplugging -- sigh.)

 - Remove some bogus assignments of platform_bus_type; that's done by
   the platform_bus code.

 - Add some FIXMEs for drivers with that pointless two-level idiom for
   probe() and remove() routines.  ("Obfuscation" is a non-goal.)
   That should help avoid future bus glue which copies that idiom.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-24 21:16:35 -07:00
David Brownell
caa9ef672a USB: ehci tolerates some buggy devices
This teaches EHCI how to to work around bugs in certain high speed
devices, by accomodating "bulk" packets that exceed the 512 byte
constant value required by the USB 2.0 specification.  (Have a
look at section 5.8.3, paragraphs 1 and 3.)

It also makes the descriptor parsing code warn when it encounters
such bugs.  (We've had reports of maybe two or three such devices,
all pretty recent.)

Such devices are nonconformant.  The proper fix is have the vendors
of those devices do the simple, obvious, and correct thing ... which
will let them be used with USB hosts that don't have workarounds for
this particular vendor bug.  But unless/until they do, we can at least
have one of the high speed HCDs work with such buggy devices.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-24 21:16:35 -07:00
David Brownell
e01e7fe388 USB: ohci: port reset paranoia timeout
This limits how long the OHCI port reset loop waits for the hardware
to do its job, if the controller either (a) dies, or (b) can't finish
the reset.  Such limits are always a good idea.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-24 21:16:34 -07:00
David Brownell
9776afc8b3 USB: ehci: minor cleanups
Minor cleanups to the EHCI code:  revision history is what source
code repositories should have.  Switch to a more standard way to
kick in verbose debugging -- don't be EHCI-specific.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-24 21:16:34 -07:00
Andrew Morton
1409e8e0e4 USB: usb-ohci-sm501-driver: use the conventional convention for suspend and resume
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-24 21:16:34 -07:00
Alan Stern
feccc30d90 USB: remove CONFIG_USB_PERSIST setting
This patch (as1047) removes the USB_PERSIST Kconfig option, enabling
it permanently.  It also prevents the power/persist attribute from
being created for hub devices; there's no point in having it since
USB-PERSIST is always turned on for hubs.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-24 21:16:32 -07:00
Alan Stern
3bb1af5243 USB: EHCI: carry out port handover during each root-hub resume
This patch (as1044) causes EHCI port handover for non-high-speed
devices to occur during every root-hub resume, not just in cases where
the controller lost power or was reset.  This is necessary because:

	When some machines go into suspend, they remove power from
	on-board USB devices while retaining suspend current for USB
	controllers.

	The user might well unplug a USB device while the system is
	suspended and then plug it back in before resuming.

A corresponding change is made to the core resume routine; now
high-speed root hubs will always be resumed when the system wakes up,
even if they were suspended before the system went to sleep.  If this
weren't done then EHCI port handover wouldn't work, since it is called
when the EHCI root hub is resumed.

Finally, a comment is added to the hub driver explaining the khubd has
to be freezable; if it weren't frozen then it could interfere with
port handover.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-24 21:16:32 -07:00
Russell King
adf6d34e46 Merge branch 'omap2-upstream' into devel 2008-04-19 17:17:29 +01:00
Kay Sievers
f4fce61d41 usb host: fix platform driver hotplug/coldplug
Since 43cc71eed1, the platform modalias is
prefixed with "platform:".  Add MODULE_ALIAS() to the hotpluggable USB HCDs,
to allow re-enable auto loading.

[dbrownell@users.sourceforge.net: more drivers; registration fixes]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-11 08:06:44 -07:00
Richard Kennedy
9cebcdc7fb USB: ohci: fix 2 timers to fire at jiffies + 1s
Code inspection discovered in 2 places timers were being incorrectly setup
using round_jiffies_relative(HZ).  The timer would then fire at time (0 <= T <
HZ).

Fix them to use round_jiffies(jiffies + HZ);

Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-02 15:06:09 -07:00
David Brownell
cdc647a9b7 USB: another ehci_iaa_watchdog fix
This patch, suggested by Alan Stern, fixes the hung USB issues
on my notebook from suspend/resume cycles.

It does so by eliminating some confusion about the internal state
machine associated with unlinking from the EHCI async schedule ring,
which caused a recent regression:

  http://bugzilla.kernel.org/show_bug.cgi?id=10345

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-02 15:06:08 -07:00
Lennert Buytenhek
705a752162 plat-orion: make ehci-orion available for all Orion families
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
2008-03-27 14:51:40 -04:00
Lennert Buytenhek
92aecfa955 ehci-orion: mbus decode window support
Make it possible to pass mbus_dram_target_info to the ehci-orion
driver via the platform data, make the ehci-orion driver program
the window registers based on this data if it is passed in, and
make the Orion platform setup code use this method instead of
programming the EHCI mbus window registers by hand.

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
2008-03-27 14:51:39 -04:00
Rene Herman
055b93c9e3 USB: ehci: stop vt6212 bus hogging
The VIA VT6212 defaults to only waiting 1us between passes over EHCI's
async ring, which hammers PCI badly ... and by preventing other devices
from accessing the bus, causes problems like drops in IDE throughput,
a problem that's been bugging users of those chips for several years.

A (partial) datasheet for this chip eventually turned up, letting us
see how to make it use a VIA-specific register to switch over to the
the normal 10us value instead, as suggested by the EHCI specification
Solution noted by Lev A. Melnikovsky.

It's not clear whether this register exists on other VIA chips; we
know that it's ineffective on the vt8235.  So this patch only applies
to chips that seem to be incarnations of the (discrete) vt6212.

Signed-off-by: Rene Herman <rene.herman@gmail.com>
Tested-by: Lev A. Melnikovsky <melnikovsky@mail.ru>
Tested-by: Alessandro Suardi <alessandro.suardi@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-03-24 22:26:15 -07:00
David Brownell
e82cc1288f USB: fix ehci unlink regressions
The recent EHCI driver update to split the IAA watchdog timer out from
the other timers made several things work better, but not everything;
and it created a couple new issues in bugzilla.  Ergo this patch:

  - Handle a should-be-rare SMP race between the watchdog firing
    and (very late) IAA interrupts;

  - Remove a shouldn't-have-been-added WARN_ON() test;

  - Guard against one observed OOPS;

  - If this watchdog fires during clean HC shutdown, it should act
    as a NOP instead of interfering with the shutdown sequence;

  - Guard against silicon errata hypothesized by some vendors:
      * IAA status latch broken, but IAAD cleared OK;
      * IAAD wasn't cleared when IAA status got reported;

The WARN_ON is in bugzilla as 10168; the OOPS as 10078; these are
both regressions.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Tested-by: Gordon Farquharson <gordonfarquharson@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-03-10 16:42:27 -07:00
Anti Sullin
0ed930bffa USB: isp116x: fix enumeration on boot
This patch removes the buffering of the status register.
USB core behavior has changed a bit and this buffering was not refreshed
at the right time.  The core got buffered old value of HCRHPORT and it
did not detect any devices on boot.

Signed-off-by: Anti Sullin <anti.sullin@artecdesign.ee>
Acked by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-03-04 14:57:43 -08:00
Misha Zhilin
b5f7a0ec11 USB: ehci: handle large bulk URBs correctly (again)
USB: ehci: Fixes completion for multi-qtd URB the short read case

When use of urb->status in the EHCI driver was reworked last August
(commit 14c04c0f88), a bug was inserted
in the handling of early completion for bulk transactions that need
more than one qTD (e.g. more than 20KB in one URB).

This patch resolves that problem by ensuring that the early completion
status is preserved until the URB is handed back to its submitter,
instead of resetting it after each qTD.

Signed-off-by: Misha Zhilin <misha@epiphan.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-03-04 14:57:43 -08:00
Mirco Tischler
038eb0ea04 Fix u132-hcd.c compile error
This fixes the following compile error caused by commit
3a2d5b7001 ("PM: Introduce
PM_EVENT_HIBERNATE callback state")

    CC [M]  drivers/usb/host/u132-hcd.o
  drivers/usb/host/u132-hcd.c: In function ‘u132_suspend’:
  drivers/usb/host/u132-hcd.c:3224: error: expected expression before ‘int’
  drivers/usb/host/u132-hcd.c:3225: error: ‘ports’ undeclared (first use in this function)
  ...

Signed-off-by: Mirco Tischler <mt-ml@gmx.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-23 20:29:09 -08:00
Rafael J. Wysocki
3a2d5b7001 PM: Introduce PM_EVENT_HIBERNATE callback state
During the last step of hibernation in the "platform" mode (with the
help of ACPI) we use the suspend code, including the devices'
->suspend() methods, to prepare the system for entering the ACPI S4
system sleep state.

But at least for some devices the operations performed by the
->suspend() callback in that case must be different from its operations
during regular suspend.

For this reason, introduce the new PM event type PM_EVENT_HIBERNATE and
pass it to the device drivers' ->suspend() methods during the last phase
of hibernation, so that they can distinguish this case and handle it as
appropriate.  Modify the drivers that handle PM_EVENT_SUSPEND in a
special way and need to handle PM_EVENT_HIBERNATE in the same way.

These changes are necessary to fix a hibernation regression related
to the i915 driver (ref. http://lkml.org/lkml/2008/2/22/488).

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Jeff Chua <jeff.chua.linux@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-23 10:40:04 -08:00
Anton Vorontsov
b5937a415f ehci-fsl: add PPC_MPC837x to default y
This patch converts USB_EHCI_FSL config option into the verbose
bool, so we'll able to select it for other freescale processors
with built-in EHCI controller.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-02-21 15:38:56 -08:00
Anton Vorontsov
c6dd2e61d3 USB: POWERPC: ehci: fix ppc build
Currently, this setup:
CONFIG_USB_ARCH_HAS_EHCI=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_EHCI_HCD_PPC_OF=y

Will fail to build:
  CC      drivers/usb/host/ehci-hcd.o
drivers/usb/host/ehci-hcd.c:1018:2: error: #error "missing bus glue for ehci-hcd"
make[3]: *** [drivers/usb/host/ehci-hcd.o] Error 1

ehci-hcd.c actually contains OF_PLATFORM_DRIVER glue, so error is bogus.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-02-21 15:38:56 -08:00
David Brownell
e1a491429e USB: fix previous sparse fix which was incorrect
The previous fix for a "sparse" warning in ehci_urb_dequeue() was
incorrect.  After rescheduling interrupt transfers it returned the
URB's completion status, not status for the dequeue operation itself.

This patch resolves that issue, cleans up the code in the reschedule
path, and shrinks the object code by a dozen bytes.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-02-21 15:38:51 -08:00
Peter Korsgaard
618b886705 USB: ehci-fsl: mpc834x config symbol is PPC_MPC834x, not MPC834x
The config symbol for mpc834x processors is CONFIG_PPC_MPC834x,
not CONFIG_MPC834x.

Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-02-21 15:38:50 -08:00
Linus Torvalds
215e871aaa Merge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/pci-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/pci-2.6: (64 commits)
  PCI: make pci_bus a struct device
  PCI: fix codingstyle issues in include/linux/pci.h
  PCI: fix codingstyle issues in drivers/pci/pci.h
  PCI: PCIE ASPM support
  PCI: Fix fakephp deadlock
  PCI: modify SB700 SATA MSI quirk
  PCI: Run ACPI _OSC method on root bridges only
  PCI ACPI: AER driver should only register PCIe devices with _OSC
  PCI ACPI: Added a function to register _OSC with only PCIe devices.
  PCI: constify function pointer tables
  PCI: Convert drivers/pci/proc.c to use unlocked_ioctl
  pciehp: block new requests from the device before power off
  pciehp: workaround against Bad DLLP during power off
  pciehp: wait for 1000ms before LED operation after power off
  PCI: Remove pci_enable_device_bars() from documentation
  PCI: Remove pci_enable_device_bars()
  PCI: Remove users of pci_enable_device_bars()
  PCI: Add pci_enable_device_{io,mem} intefaces
  PCI: avoid save the same type of cap multiple times
  PCI: correctly initialize a structure for pcie_save_pcix_state()
  ...
2008-02-02 14:29:33 +11:00
bjorn.helgaas@hp.com
f0fda801da PCI: use dev_printk in quirk messages
Convert quirk printks to dev_printk().

I made the MSI disable messages a little more consistent:

    - always use "disabled", not "deactivated"
    - specify "device MSI disabled" or "subordinate MSI disabled" when
      disabling MSI for only a specific device or subordinate bus

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-02-01 15:04:26 -08:00
David Brownell
c06d4dcf50 usb: ehci should use u16 for isochronous intervals
While most isochronous endpoints have short polling intervals, the
EHCI driver won't necessarily handle larger ones correctly.

This patch switches to use a "u16" to represent those periods, not
a u8, since it can always work:  the largest expressible period
is 2^15 units ... not the previous too-short limit of 128 frames
(full or low speeds) or microframes (high speed, 32 frames).

This bug is essentially theoretical, since the few ISO endpoints
I've seen which don't use one transfer per frame are high speed
ones using more than that (including high bandwidth, 24 KB/msec).

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-02-01 14:35:06 -08:00
David Brownell
cd4cdc93ce usb: ehci, remove false clear-reset path
Some of the "EHCI ports reset forever" problems may be explained by
code paths which wrongly flagged resets as complete.  This removes
two such paths; the ehci_hub_status_data() path should be the only one
to have an effect, since it was already properly flagged on the other
path.  (Issue noted by Minhyoung Kim <a9a9@lge.com>.)

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-02-01 14:35:06 -08:00
Magnus Damm
f54aab6ebc usb: ohci-sm501 driver
usb: ohci-sm501 driver V2

This patch adds sm501 ohci support. It's all very straightforward with the
exception of dma_declare_coherent_memory() and HCD_LOCAL_MEM. Together they
are used to ensure that usb data is allocated using dma_alloc_coherent(),
and that only valid dma memory is used to allocate from. This driver is
a platform device, and the mfd driver sm501.c is already creating one
usb host controller instance per sm501.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-02-01 14:35:05 -08:00
Yoshihiro Shimoda
828d55c58c USB: add support for SuperH OHCI
add support for SuperH OHCI.

supported CPU are:
 - SH7720
 - SH7721
 - SH7763

Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-02-01 14:35:03 -08:00