Conflicts:
net/core/rtnetlink.c
net/core/skbuff.c
Both conflicts were very simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Lars writes: "I'm only 99% sure that the net interfaces are qmi
interfaces, nothing to lose by adding them in my opinion."
And I tend to agree based on the similarity with the two Olicard
modems we already have here.
Reported-by: Lars Melin <larsm17@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
include/net/inetpeer.h
net/ipv6/output_core.c
Changes in net were fixing bugs in code removed in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Each iPad model has a different product id, this patch adds support for iPad 2
(pid 0x12a2) and iPad 3 (pid 0x12a6). Note that iPad 2 must be jailbroken and a
third-party app must be used for tethering to work. On iPad 3, tethering works
out of the box (assuming your ISP is nice).
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The min_tx_pkt variable decides the cutoff point where the driver
will stop padding out NTBs to maximum size. The padding is a tradeoff
where we use some USB bus bandwidth to allow the device to receive
fixed size buffers. Different devices will have different optimal
settings, spanning from no padding at all to padding every NTB.
There is no way to automatically figure out which setting is best
for a specific device.
The default value is a reasonable tradeoff, calculated based on the
USB packet size and out NTB max size. This may have to be changed
along with any tx_max changes.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mandatory GetNtbParameters control request is an important part of
the host <-> device protocol negotiation in CDC NCM (and CDC MBIM). It
gives device limits which the host must obey when configuring the
protocol aggregation variables. The driver will enforce this by
rejecting attempts to set any of the tunable variables to a value
which is not supported by the device. Exporting the parameter block
helps userspace decide which values are allowed without resorting
to trial and error.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool coalesce API is not applicable for this driver. Forcing
it to fit the NCM aggregation redefined the API in a driver specific
way, which is much worse than defining a clean new API. These ethtool
coalesce functions have therefore been replaced by a new sysfs API.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Attach a driver specific sysfs group to the netdev, and use it
for the rx/tx aggregation variables.
The datagram aggregation defined by the CDC NCM specification is
specific to this device class (including CDC MBIM). Using the
ethtool interrupt coalesce API as an interface to the aggregation
parameters redefined that API in a driver specific and confusing
way. A sysfs group
- makes it clear that this is a driver specific userspace API, and
- allows us to export the real values instead of some translated
version, and
- lets us include more aggregation variables which were impossible
to force into the ethtool API.
Additionally, using sysfs allows tuning the driver on space
constrained hosts where userspace tools like ethtool are undesired.
Suggested-by: Peter Stuge <peter@stuge.se>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
It doesn't matter whether the buffer size goes up or down. We have to
keep usbnet and device syncronized to be able to split transfers at the
correct boundaries. The spec allow skipping short packets when using
max sized transfers. If we don't tell usbnet about our new expected rx
buffer size, then it will merge and/or split NTBs. The driver does not
support this, and the result will be lots of framing errors.
Fix by always reallocating usbnet rx buffers when the rx_max value
changes.
Fixes: 68864abf08 ("net: cdc_ncm: support rx_max/tx_max updates when running")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are calling usbnet_start_xmit() to flush any remaining data,
depending on the side effect that tx_curr_skb is set to NULL,
ensuring a new allocation using the updated tx_max. But this
side effect will only happen if there were any cached data ready
to transmit. If not, then an empty tx_curr_skb is still allocated
using the old tx_max size. Free it to avoid a buffer overrun.
Fixes: 68864abf08 ("net: cdc_ncm: support rx_max/tx_max updates when running")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cloning the big skbs we use for USB buffering chokes up TCP and
SCTP because the socket memory limits are hitting earlier than
they should. It is better to unconditionally copy the unwrapped
packets to freshly allocated skbs.
Reported-by: Jim Baxter <jim_baxter@mentor.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This interface is unusable, as the cdc-wdm character device doesn't reply to
any QMI command. Also, the out-of-tree Sierra Wireless GobiNet driver fully
skips it.
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
A set of new VID/PIDs retrieved from the out-of-tree GobiNet/GobiSerial
Sierra Wireless drivers.
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This issue was reported by coccicheck using the semantic patch
at scripts/coccinelle/api/memdup.cocci
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a typo here where we test for USB_CDC_NCM_NTH32_SIGN instead
of USB_CDC_NCM_NTB32_SUPPORTED. The test probably still works as
written because 0x686D636E has (1 << 1) set and doesn't have (1 << 0)
set.
Fixes: f8afb73da3 ('net: cdc_ncm: factor out one-time device initialization')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The upper timer_interval limit is arbitrary and much higher
than anything usable in the real world. Reducing it from 15s
to ~4s to make the timer_interval fit in an u32 does not make
much difference. The limit is still outside the practical
bounds.
This eliminates the need for a 64bit timer_interval, fixing a
build error related to 64bit division:
drivers/built-in.o: In function `cdc_ncm_get_coalesce':
ak8975.c:(.text+0x1ac994): undefined reference to `__aeabi_uldivmod'
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can end up with a freshly allocated tx_curr_skb with no frames
in it. In this case it does not make any sense to start the timer.
This avoids the timer periodically trying to start tx when there
is nothing in the queue.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling netif_carrier_{on,off} is sufficient. There is no need
to duplicate the carrier state in a driver specific flag.
Acked-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of devices request much larger buffers than reasonable. This
cause real problems for users of hosts with limited resources.
Reducing the default buffer size to 16kB for such devices is
a reasonable trade-off between allowing them to aggregate traffic
and avoiding memory exhaustion on resource restrained hosts.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
To have an idea of the effects of the protocol coalescing
it's useful to have some counters showing the different
aspects.
Due to the asymmetrical usbnet interface the netdev
rx_bytes counter has been counting real received payload,
while the tx_bytes counter has included the NCM/MBIM
framing overhead. This overhead can be many times the
payload because of the aggressive padding strategy of
this driver, and will vary a lot depending on device
and traffic.
With very few exceptions, users are only interested in
the payload size. Having an somewhat accurate payload
byte counter is particularly important for mobile
broadband devices, which many NCM devices and of course
all MBIM devices are. Users and userspace applications
will use this counter to monitor account quotas.
Having protocol specific counters for the overhead, we are
now able to correct the tx_bytes netdev counter so that
it shows the real payload
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
We pad frames larger than X to maximum size for devices which
don't need a ZLP after maximum sized frames. This allows the
device to optimize its transfers for one fixed buffer size.
X was arbitrarily set at 512 bytes regardless of real buffer
maximum, causing extreme overheads due to excessive padding of
larger tx buffers. Limit the padding to at most 3 full USB
packets, still allowing the overhead to payload ratio of 3/1.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many newer NCM and MBIM devices will request a maximum tx
datagram count which is much smaller than our hard-coded
absolute max. We can reduce the overhead without sacrificing
any of the simplicity for these devices, by simply using the
true negotiated count in when calculated the maximum NTH and
NDP header sizes.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Datagram coalescing is an integral part of the NCM and MBIM
protocols, intended to reduce the interrupt load primarily
on the device end of the USB link. As with all coalescing
solutions, there is a trade-off between buffering and
interrupts.
The current defaults are based on the assumption that device
side buffers should be the limiting factor. However, many
modern high speed LTE modems suffers from buffer-bloat,
making this assumption fail. This results in sub-optimal
performance due to excessive coalescing. And in cases where
such modems are connected to cheap embedded hosts there is
often severe buffer allocation issues, giving very noticeable
performance degradation .
A start on improving this is going from build time hard
coded limits to per device user configurable limits. The
ethtool coalescing API was selected as user interface
because, although the tuned values are buffer sizes, these
settings directly control datagram coalescing.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Finish the rx_max/tx_max setup by flushing buffers and
informing usbnet about the changes. This way, the settings
can be modified while the netdev is up and running.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have split out the part of the device setup
which MUST be done with the data interface in altsetting 0,
we can delay the rest of the initialization. This allows us
to move some of post-init buffer size config from bind to
the appropriate setup function.
The purpose of this refactoring is to collect all code
adjusting the rx_max and tx_max buffers in one place, so
that it is easier to call it from multiple call sites.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split the parts of setup dealing with device initialization from
parts just setting defaults for attributes which might be
changed after initialization.
Some commands of the device initialization are only allowed when
the data interface is in its disabled altsetting, so we must
separate them out of we are to allow rerunning parts of setup.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split out the part of setup dealing with updating the rx_max
and tx_max buffer sizes so that this code can be reused for
dynamically updating the limits.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NCM class match in the cdc_mbim driver is confusing and
cause unexpected behaviour. The USB core guarantees that a
USB interface is in altsetting 0 when probing starts. This
means that devices implementing a NCM 1.0 backwards
compatible MBIM function (a "NCM/MBIM function") always hit
the NCM entry in the cdc_mbim driver match table. Such
functions will never match any of the MBIM entries.
This causes unexpeced behaviour for cases where the NCM and
MBIM entries are differet, which is currently the case for
all except Ericsson devices.
Improve the probing of NCM/MBIM functions by looking up the
device again in the cdc_mbim match table after switching to
the MBIM identity.
The shared altsetting selection is updated to better
accommodate the new probing logic, returning the preferred
altsetting for the control interface instead of the data
interface. The control interface altsetting update is moved
to the cdc_mbim driver. It is never necessary to change the
control interface altsetting for NCM.
Cc: Greg Suarez <gsuarez@smithmicro.com>
Reported by: Yu-an Shih <yshih@nvidia.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSS VLANs are pseudo network interfaces representing arbitrary
data streams, and specifically not IP. Preventing spurious IP
packets can sometimes be a hassle. The kernel will for example
send an IPv6 Router Solicit when the interface is brought up
unless the user has been careful enough to disable IPv6 first.
Such packets forwared to a MBIM DSS session will look like
spurious noise to the device, and can cause it to log an error
or even malfunction.
Drop all IP packets on the designated DSS VLANs to prevent such
unwanted spurious transmissions.
Cc: Greg Suarez <gsuarez@smithmicro.com>
Reported-by: Arnaud Desmier <adesmier@sequans.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cdc_mbim driver maps 802.1q VLANs to MBIM IP and DSS
sessions. MBIM IP session 0 is handled as an exception and
is mapped to untagged frames.
This patch adds optional support for remapping MBIM IP
session 0 to 802.1q VLAN ID 4094 instead. The default
behaviour is not changed. The new behaviour is triggered
by adding a link for this previously unsupported VLAN.
The untagged mapping was chosen initially to support the
assumed most common use case: Most current MBIM devices only
support a single IP session (i.e. session 0 only), and using
untagged frames lets the users completely ignore the
additonal complexity of the multiplexing layer.
But when the multiplexing features of MBIM are used, then
this netdev gets a double meaning: It becomes the master
interface for all the VLAN subdevs the additional sessions
are mapped to, while still serving as the untagged IP
interface for session 0.
This can be problematic, especially when using Device Service
Streams (DSS), as have become apparent recently with the
availability of devices with real DSS support. Some use cases
need to e.g set a MTU which is higher than allowed for IP
Session 0. The dual role also leads to the situation where
the IP Session 0 interface cannot be taken down without
breaking unrelated IP or DSS sessions - a devastating side
effect which applications managing a simple IP session cannot
be expected to be aware of. A typical DHCP client will assume
that it should bring the interface down after releasing the
IP lease.
These problems can be avoided by tagging IP session 0 packets
too, making this session similar to all other multiplexed
sessions. This redefines the main netdev as an upper master
interface only.
Cc: Greg Suarez <gsuarez@smithmicro.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
net: get rid of SET_ETHTOOL_OPS
Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.
Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
- SET_ETHTOOL_OPS(dev, ops);
+ dev->ethtool_ops = ops;
Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: Dave Miller <davem@davemloft.net>
Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __vlan_find_dev_deep should always called in RCU, according
David's suggestion, rename to __vlan_find_dev_deep_rcu looks more
reasonable.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver maps 802.1q VLANs to MBIM sessions. The mapping is based on
a bogus assumption that all tagged frames will use the acceleration API
because we enable NETIF_F_HW_VLAN_CTAG_TX. This fails for e.g. frames
tagged in userspace using packet sockets. Such frames will erroneously
be considered as untagged and silently dropped based on not being IP.
Fix by falling back to looking into the ethernet header for a tag if no
accelerated tag was found.
Fixes: a82c7ce5bc ("net: cdc_ncm: map MBIM IPS SessionID to VLAN ID")
Cc: Greg Suarez <gsuarez@smithmicro.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4d619f625a ("net: cdc_ncm: no point in filling up the NTBs
if we send ZLPs") changed the padding logic for devices with the ZLP
flag set. This meant that frames of any size will be sent without
additional padding, except for the single byte added if the size is
a multiple of the USB packet size. But if the unpadded size is
identical to the maximum frame size, and the maximum size is a
multiplum of the USB packet size, then this one-byte padding will
overflow the buffer.
Prevent padding if already at maximum frame size, letting usbnet
transmit a ZLP instead in this case.
Fixes: 4d619f625a ("net: cdc_ncm: no point in filling up the NTBs if we send ZLPs")
Reported by: Yu-an Shih <yshih@nvidia.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan writes:
"The Dell drivers use the same configuration for PIDs:
81A2: Dell Wireless 5806 Gobi(TM) 4G LTE Mobile Broadband Card
81A3: Dell Wireless 5570 HSPA+ (42Mbps) Mobile Broadband Card
81A4: Dell Wireless 5570e HSPA+ (42Mbps) Mobile Broadband Card
81A8: Dell Wireless 5808 Gobi(TM) 4G LTE Mobile Broadband Card
81A9: Dell Wireless 5808e Gobi(TM) 4G LTE Mobile Broadband Card
These devices are all clearly Sierra devices, but are also definitely
Gobi-based. The A8 might be the MC7700/7710 and A9 is likely a MC7750.
>From DellGobi5kSetup.exe from the Dell drivers:
usbif0: serial/firmware loader?
usbif2: nmea
usbif3: modem/ppp
usbif8: net/QMI"
Reported-by: AceLan Kao <acelan.kao@canonical.com>
Reported-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of older CMOTech modems are based on Qualcomm
chips and exporting a QMI/wwan function.
Reported-by: Lars Melin <larsm17@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the device is unplugged, the driver would try to disable the
device. Add checking the flag of RTL8152_UNPLUG to skip setting
the device when it is unplugged. This could shorten the time of
unloading the driver.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device provides QMI and ethernet functionality via a standard CDC
ethernet descriptor. But when driven by cdc_ether, the QMI
functionality is unavailable because only cdc_ether can claim the USB
interface. Thus blacklist the device in cdc_ether and add its IDs to
qmi_wwan, which enables both QMI and ethernet simultaneously.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/marvell/mvneta.c
The mvneta.c conflict is a case of overlapping changes,
a conversion to devm_ioremap_resource() vs. a conversion
to netdev_alloc_pcpu_stats.
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a race which happens by freeing an object on the stack.
Quoting Julius:
> The issue is
> that it calls usbnet_terminate_urbs() before that, which temporarily
> installs a waitqueue in dev->wait in order to be able to wait on the
> tasklet to run and finish up some queues. The waiting itself looks
> okay, but the access to 'dev->wait' is totally unprotected and can
> race arbitrarily. I think in this case usbnet_bh() managed to succeed
> it's dev->wait check just before usbnet_terminate_urbs() sets it back
> to NULL. The latter then finishes and the waitqueue_t structure on its
> stack gets overwritten by other functions halfway through the
> wake_up() call in usbnet_bh().
The fix is to just not allocate the data structure on the stack.
As dev->wait is abused as a flag it also takes a runtime PM change
to fix this bug.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Reported-by: Grant Grundler <grundler@google.com>
Tested-by: Grant Grundler <grundler@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
Documentation/devicetree/bindings/net/micrel-ks8851.txt
net/core/netpoll.c
The net/core/netpoll.c conflict is a bug fix in 'net' happening
to code which is completely removed in 'net-next'.
In micrel-ks8851.txt we simply have overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
According to "Universal Serial Bus Communications Class Subclass
Specification for Mobile Broadband Interface Model, Revision 1.0,
Errata-1" published by USB-IF, the wMTU field of the MBIM extended
functional descriptor indicates the operator preferred MTU for IP data
streams.
This patch modifies cdc_ncm_setup to ensure that the MTU value set on
the usbnet device does not exceed the operator preferred MTU indicated
by wMTU if the MBIM device exposes a MBIM extended functional
descriptor.
Signed-off-by: Ben Chan <benchan@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
