This patch fixes the return type of b43_plcp_get_bitrate_idx_ofdm. If
the plcp contains an error, the function return value is 255 instead
of -1, and the packet was not dropped. This causes a warning in
__ieee80211_rx function because rate idx is out of range.
Cc: stable@kernel.org
Signed-off-by: Lorenzo Nava <navalorenx@gmail.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This changes the RX handler to pass more status flags to mac80211.
It also changes part of the drop policy, if bad frames were requested. (Note that
currently mac80211 will throw a WARN_ON in that case. But nothing bad will happen).
This also removes some obsolete unused timestamping code.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I frequently run into this warning, and added some
debugging to see why, and got this:
b43 bad rx: 00000000: 2f d2 e2 63 cf a7 14 04 28 18 c8 5f 88 4a a2 00
bogus junk | plcp | fctl| dur
b43 bad rx: 00000010: 00 11 24 91 07 4d 00 06 25 ff 8f 78 00 06 25 ff
my MAC address | BSSID | AP MAC
b43 bad rx: 00000020: 8f 76 20 74 00 00 42 07 00 20 00 00 00 00 aa aa
| seq | QoS | CCMP IV | data
...
As you can see, there are 6 bogus bytes (sometimes only five) and then
the frame. I don't know why, and I don't see how to recover, so let's
just drop these frames.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
So after the previous changes we were still unhappy with how
convoluted the API is and decided to make things simpler for
everybody. This completely changes the rate control API, now
taking into account 802.11n with MCS rates and more control,
most drivers don't support that though.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adjusts the rate control API to allow multi-rate retry
if supported by the driver. The ieee80211_hw struct specifies how
many alternate rate selections the driver supports.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Free up 2 bytes in skb->cb to be used for multi-rate retry later.
Move iv_len and icv_len initialization into key alloc.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch rewrites the TX power recalculation algorithms to scale better
with changed enviromnent. If there's low
TX traffic, the power will be checked against the desired values
every 60 seconds.
If there is high TX traffic, the check is redone every 2 seconds. This improves
the reaction times a lot and confuses the rate control less.
It will also reduce the time it initially takes to tune to a new TX power
value. With the old algorithm it could take about 30 to 45 seconds to settle to
a new power value. This will happen in about two to four seconds now.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implements a dynamic "ops" based PHY API.
This is needed in order to conveniently support future PHY types
to avoid the "switch"-hell.
This patch does not change any functionality. It just moves lots
of code from one place to another and adjusts it for the changed
data structures.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes mac80211 to not use the skb->cb over the queue step
from virtual interfaces to the master. The patch also, for now,
disables aggregation because that would still require requeuing,
will fix that in a separate patch. There are two other places (software
requeue and powersaving stations) where requeue can happen, but that is
not currently used by any drivers/not possible to use respectively.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes mac80211 assign proper sequence numbers to
QoS-data frames. It also removes the old sequence number code
because we noticed that only the driver or hardware can assign
sequence numbers to non-QoS-data and especially management
frames in a race-free manner because beacons aren't passed
through mac80211's TX path.
This patch also adds temporary code to the rt2x00 drivers to
not break them completely, that code will have to be reworked
for proper sequence numbers on beacons.
It also moves sequence number assignment down in the TX path
so no sequence numbers are assigned to frames that are dropped.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch converts mac80211 and all drivers to have transmit
information and status in skb->cb rather than allocating extra
memory for it and copying all the data around. To make it fit,
a union is used where only data that is necessary for all steps
is kept outside of the union.
A number of fixes were done by Ivo, as well as the rt2x00 part
of this patch.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch modifies struct ieee80211_tx_control to give band
info and the rate index (instead of rate pointers) to drivers.
This mostly serves to reduce the TX control structure size to
make it fit into skb->cb so that the fragmentation code can
put it there and we can think about passing it to drivers that
way in the future.
The rt2x00 driver update was done by Ivo, thanks.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
trying to clean up the signal/noise code. the previous code in mac80211 had
confusing names for the related variables, did not have much definition of
what units of signal and noise were provided and used implicit mechanisms from
the wireless extensions.
this patch introduces hardware capability flags to let the hardware specify
clearly if it can provide signal and noise level values and which units it can
provide. this also anticipates possible new units like RCPI in the future.
for signal:
IEEE80211_HW_SIGNAL_UNSPEC - unspecified, unknown, hw specific
IEEE80211_HW_SIGNAL_DB - dB difference to unspecified reference point
IEEE80211_HW_SIGNAL_DBM - dBm, difference to 1mW
for noise we currently only have dBm:
IEEE80211_HW_NOISE_DBM - dBm, difference to 1mW
if IEEE80211_HW_SIGNAL_UNSPEC or IEEE80211_HW_SIGNAL_DB is used the driver has
to provide the maximum value (max_signal) it reports in order for applications
to make sense of the signal values.
i tried my best to find out for each driver what it can provide and update it
but i'm not sure (?) for some of them and used the more conservative guess in
doubt. this can be fixed easily after this patch has been merged by changing
the hardware flags of the driver.
DRIVER SIGNAL MAX NOISE QUAL
-----------------------------------------------------------------
adm8211 unspec(?) 100 n/a missing
at76_usb unspec(?) (?) unused missing
ath5k dBm dBm percent rssi
b43legacy dBm dBm percent jssi(?)
b43 dBm dBm percent jssi(?)
iwl-3945 dBm dBm percent snr+more
iwl-4965 dBm dBm percent snr+more
p54 unspec 127 n/a missing
rt2x00 dBm n/a percent rssi+tx/rx frame success
rt2400 dBm n/a
rt2500pci dBm n/a
rt2500usb dBm n/a
rt61pci dBm n/a
rt73usb dBm n/a
rtl8180 unspec(?) 65 n/a (?)
rtl8187 unspec(?) 65 (?) noise(?)
zd1211 dB(?) 100 n/a percent
drivers/net/wireless/ath5k/base.c: Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The hw_key_idx inside the ieee80211_key_conf structure does
not provide all the information drivers might need to perform
hardware encryption.
This is in particular true for rt2x00 who needs to know the
key algorithm and whether it is a shared or pairwise key.
By passing the ieee80211_key_conf pointer it assures us that
drivers can make full use of all information that it should know
about a particular key.
Additionally this patch updates all drivers to grab the hw_key_idx from
the ieee80211_key_conf structure.
v2: Removed bogus u16 cast
v3: Add warning about ieee80211_tx_control pointers
v4: Update warning about ieee80211_tx_control pointers
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds some minor stuff for N-PHY support. Nothing special.
Adds Analog switching and some TODOs for RSSI processing.
Just a patch I had floating around for quite some time now.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds PIO support back (D'oh!) for PCMCIA devices.
This is a complete rewrite of the old PIO code. It does actually work
and we get reasonable performance out of it on a modern machine.
On a PowerBook G4 I get a few MBit for TX and a few more for RX.
So it doesn't work as well as DMA (of course), but it's a _lot_ faster
than the old PIO code (only got a few kBit with that).
The limiting factor is the host CPU speed. So it will generate 100%
CPU usage when the network interface is heavily loaded. A voluntary preemption
point in the RX path makes sure Desktop Latency isn't hurt.
PIO is needed for 16bit PCMCIA devices, as we really don't want to poke with
the braindead DMA mechanisms on PCMCIA sockets. Additionally, not all
PCMCIA sockets do actually support DMA in 16bit mode (mine doesn't).
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds QOS support to the b43 driver.
QOS can be disabled on driver level with a module parameter for debugging purposes.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Having the full RX timestamp in beacons is necessary for IBSS
merge to work properly so extend the 16-bit timestamp to the
full 64 bits for beacon frames (as well as when monitor mode
is active.)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch creates new cfg80211 wiphy API for channel and bitrate
registration and converts mac80211 and drivers to the new API. The
old mac80211 API is completely ripped out. All drivers (except ath5k)
are updated to the new API, in many cases I expect that optimisations
can be done.
Along with the regulatory code I've also ripped out the
IEEE80211_HW_DEFAULT_REG_DOMAIN_CONFIGURED flag, I believe it to be
unnecessary if the hardware simply gives us whatever channels it wants
to support and we then enable/disable them as required, which is pretty
much required for travelling.
Additionally, the patch adds proper "basic" rate handling for STA
mode interface, AP mode interface will have to have new API added
to allow userspace to set the basic rate set, currently it'll be
empty... However, the basic rate handling will need to be moved to
the BSS conf stuff.
I do expect there to be bugs in this, especially wrt. transmit
power handling where I'm basically clueless about how it should work.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We must not transmit packets we're not able to encrypt.
This fixes a bug where in a tiny timeframe after machine resume
packets can get sent unencrypted and might leak information.
This also fixes three small resource leakages I spotted while fixing
the security problem. Properly deallocate the DMA slots in any DMA
allocation error path.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes suspend/resume.
We must not overwrite the MAC addresses on resume. Otherwise
the card won't ACK any packets anymore.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for new firmware.
Old firmware is still supported until July 2008.
To get new firmware, go to
ftp://ftp.linksys.com/opensourcecode/wrt150nv11/1.51.3/
and download the tarball. We don't have a smaller tarball, yet.
That will be fixed later.
You can extract firmware out of the "wl_ap.o" file contained
in this tarball using latest fwcutter. You must pass the option
--unsupported to fwcutter.
Fwcutter-010 with official support for a new firmware image will
be released soon.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch gets rid of the if_id stuff where possible in favour of
a new per-virtual-interface structure "struct ieee80211_vif". This
structure is located at the end of the per-interface structure and
contains a variable length driver-use data area.
This has two advantages:
* removes the need to look up interfaces by if_id, this is better
for working with network namespaces and performance
* allows drivers to store and retrieve per-interface data without
having to allocate own lists/hash tables
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove b43 PIO support.
DMA works well on all supported devices. There's no reason to use PIO.
Additionally, new devices don't support PIO in hardware anymore.
b43 PIO support is dead and unused code.
After applying this patch please do
git rm drivers/net/wireless/b43/pio.h
git rm drivers/net/wireless/b43/pio.c
to remove the main PIO support code.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes antenna selection in b43. It adds a sanity check
for the antenna numbers we get from mac80211.
This patch depends on
ssb: Fix extraction of values from SPROM
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes it can be useful to see the FCS, especially when
bad-FCS frames are shown. Pass the FCS to mac80211 and let
it worry about snipping it off when required.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The b43 driver is modified to use the new SPROM structure.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix my copyright notices in b43 and b43legacy.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Cc: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the limits provided by mac80211.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These drivers pass full mactime information to the stack, make them
indicate this via the new RX_FLAG_TSFT to get mac80211 to show this
information in monitor mode.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the parsing of the RX data header channel field.
The current code parses the header incorrectly and passes a wrong
channel number and frequency for each frame to mac80211.
The FIXMEs added by this patch don't matter for now as the code
where they live won't get executed anyway. They will be fixed later.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
