Commit b826291c, "drivercore/dt: add a match table pointer to struct
device" added an of_match pointer to struct device to cache the
of_match_table entry discovered at driver match time. This was unsafe
because matching is not an atomic operation with probing a driver. If
two or more drivers are attempted to be matched to a driver at the
same time, then the cached matching entry pointer could get
overwritten.
This patch reverts the of_match cache pointer and reworks all users to
call of_match_device() directly instead.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
TTY layer expects 0 if the ldisc->open operation succeeded.
Reported-by: Matvejchikov Ilya <matvejchikov@gmail.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTR frames do have a valid data length code on CAN.
The driver for SJA1000 did not handle that situation properly.
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 74888760d4
"dt/net: Eliminate users of of_platform_{,un}register_driver"
broke building mscan driver. Fix it.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (34 commits)
net: Add support for SMSC LAN9530, LAN9730 and LAN89530
mlx4_en: Restoring RX buffer pointer in case of failure
mlx4: Sensing link type at device initialization
ipv4: Fix "Set rt->rt_iif more sanely on output routes."
MAINTAINERS: add entry for Xen network backend
be2net: Fix suspend/resume operation
be2net: Rename some struct members for clarity
pppoe: drop PPPOX_ZOMBIEs in pppoe_flush_dev
dsa/mv88e6131: add support for mv88e6085 switch
ipv6: Enable RFS sk_rxhash tracking for ipv6 sockets (v2)
be2net: Fix a potential crash during shutdown.
bna: Fix for handling firmware heartbeat failure
can: mcp251x: Allow pass IRQ flags through platform data.
smsc911x: fix mac_lock acquision before calling smsc911x_mac_read
iwlwifi: accept EEPROM version 0x423 for iwl6000
rt2x00: fix cancelling uninitialized work
rtlwifi: Fix some warnings/bugs
p54usb: IDs for two new devices
wl12xx: fix potential buffer overflow in testmode nvs push
zd1211rw: reset rx idle timer from tasklet
...
When an interrupt occurs, the INT pin is driven low by the
MCP251x controller (falling edge) but in some cases the INT
pin can be connected to the MPU through a transistor or level
translator which inverts this signal. In this case interrupt
should be configured in rising edge.
This patch adds support to pass the IRQ flags via
mcp251x_platform_data.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (30 commits)
xfrm: Restrict extended sequence numbers to esp
xfrm: Check for esn buffer len in xfrm_new_ae
xfrm: Assign esn pointers when cloning a state
xfrm: Move the test on replay window size into the replay check functions
netdev: bfin_mac: document TE setting in RMII modes
drivers net: Fix declaration ordering in inline functions.
cxgb3: Apply interrupt coalescing settings to all queues
net: Always allocate at least 16 skb frags regardless of page size
ipv4: Don't ip_rt_put() an error pointer in RAW sockets.
net: fix ethtool->set_flags not intended -EINVAL return value
mlx4_en: Fix loss of promiscuity
tg3: Fix inline keyword usage
tg3: use <linux/io.h> and <linux/uaccess.h> instead <asm/io.h> and <asm/uaccess.h>
net: use CHECKSUM_NONE instead of magic number
Net / jme: Do not use legacy PCI power management
myri10ge: small rx_done refactoring
bridge: notify applications if address of bridge device changes
ipv4: Fix IP timestamp option (IPOPT_TS_PRESPEC) handling in ip_options_echo()
can: c_can: Fix tx_bytes accounting
can: c_can_platform: fix irq check in probe
...
The current SocketCAN implementation for the Bosch c_can cell doesn't
account the TX bytes correctly, because it calls
c_can_inval_msg_object() (which clears the msg ctrl register) before
reading the DLC value:
for (/* nix */; (priv->tx_next - priv->tx_echo) > 0; priv->tx_echo++) {
msg_obj_no = get_tx_echo_msg_obj(priv);
c_can_inval_msg_object(dev, 0, msg_obj_no);
val = c_can_read_reg32(priv, &priv->regs->txrqst1);
if (!(val & (1 << msg_obj_no))) {
can_get_echo_skb(dev,
msg_obj_no - C_CAN_MSG_OBJ_TX_FIRST);
stats->tx_bytes += priv->read_reg(priv,
&priv->regs->ifregs[0].msg_cntrl)
& IF_MCONT_DLC_MASK;
stats->tx_packets++;
}
}
So, we will always read 0 for the DLC value and "ifconfig" will report
*0* TX Bytes.
The fix is quite easy: Just move c_can_inval_msg_object() to the end of
the if() statement. So:
* We only call c_can_inval_msg_object() if the message was
actually transmitted
* We read out the DLC value _before_ clearing the msg ctrl
register
Signed-off-by: Jan Altenberg <jan@linutronix.de>
Acked-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the check in the probe function whether a IRQ was supplied
to the driver. The original driver check the irq "struct resource *" against
<= 0. Use "platform_get_irq" instead.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Bhupesh Sharma <bhupesh.sharma@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch disables the one shot mode, until the driver has been fixed and
tested to support it.
> I'm quite sure I've seen a situation where msg_obj 17 "seemed" to be
> pending, while msg_obj 18 and 19 already have been transmitted. But
> in that case, I enabled ONESHOT for the can interface, which enables
> the DA mode (automatic retransmission is disabled).
Reported-by: Jan Altenberg <jan@linutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Cc: Bhupesh Sharma <bhupesh.sharma@st.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cell's platform_data is now accessed with a helper function;
change clients to use that, and remove the now-unused data_size.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
I ran into some trouble while testing the SocketCAN driver for the BOSCH
C_CAN controller. The interface is not correctly initialized, if I put
some CAN traffic on the line, _while_ the interface is being started
(which means: the interface doesn't come up correcty, if there's some RX
traffic while doing 'ifconfig can0 up').
The current implementation enables the controller interrupts _before_
doing the basic c_can configuration. I think, this should be done the
other way round.
The patch below fixes things for me.
Signed-off-by: Jan Altenberg <jan@linutronix.de>
Acked-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of users of of_platform_driver in drivers/net. The
of_platform_{,un}register_driver functions are going away, so the
users need to be converted to using the platform_bus_type directly.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
I just found that the controller hardware name is not set for the Softing
driver. After this patch, "$ ip -d link show" looks nicer.
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (37 commits)
net: deinit automatic LIST_HEAD
net: dont leave active on stack LIST_HEAD
net: provide default_advmss() methods to blackhole dst_ops
tg3: Restrict phy ioctl access
drivers/net: Call netif_carrier_off at the end of the probe
ixgbe: work around for DDP last buffer size
ixgbe: fix panic due to uninitialised pointer
e1000e: flush all writebacks before unload
e1000e: check down flag in tasks
isdn: hisax: Use l2headersize() instead of dup (and buggy) func.
arp_notify: unconditionally send gratuitous ARP for NETDEV_NOTIFY_PEERS.
cxgb4vf: Use defined Mailbox Timeout
cxgb4vf: Quiesce Virtual Interfaces on shutdown ...
cxgb4vf: Behave properly when CONFIG_DEBUG_FS isn't defined ...
cxgb4vf: Check driver parameters in the right place ...
pch_gbe: Fix the MAC Address load issue.
iwlwifi: Delete iwl3945_good_plcp_health.
net/can/softing: make CAN_SOFTING_CS depend on CAN_SOFTING
netfilter: nf_iterate: fix incorrect RCU usage
pch_gbe: Fix the issue that the receiving data is not normal.
...
* 'fixes-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: make sure MAYDAY_INITIAL_TIMEOUT is at least 2 jiffies long
workqueue, freezer: unify spelling of 'freeze' + 'able' to 'freezable'
workqueue: wake up a worker when a rescuer is leaving a gcwq
There are two spellings in use for 'freeze' + 'able' - 'freezable' and
'freezeable'. The former is the more prominent one. The latter is
mostly used by workqueue and in a few other odd places. Unify the
spelling to 'freezable'.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Steven Whitehouse <swhiteho@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: set flow handler for secondary interrupt controller of 5249
m68knommu: remove use of IRQ_FLG_LOCK from 68360 platform support
m68knommu: fix dereference of port.tty
m68knommu: add missing linker __modver section
m68knommu: fix mis-named variable int set_irq_chip loop
m68knommu: add optimize memmove() function
m68k: remove arch specific non-optimized memcmp()
m68knommu: fix use of un-defined _TIF_WORK_MASK
m68knommu: Rename m548x_wdt.c to m54xx_wdt.c
m68knommu: fix m548x_wdt.c compilation after headers renaming
m68knommu: Remove dependencies on nonexistent M68KNOMMU
The statement 'select CAN_SOFTING' may ignore the dependancies
for CAN_SOFTING while selecting CAN_SOFTING_CS, as is therefore a bad choice.
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bosch C_CAN controller is a full-CAN implementation which is compliant
to CAN protocol version 2.0 part A and B. Bosch C_CAN user manual can be
obtained from:
http://www.semiconductors.bosch.de/media/en/pdf/ipmodules_1/c_can/users_manual_c_can.pdf
This patch adds the support for this controller.
The following are the design choices made while writing the controller
driver:
1. Interface Register set IF1 has be used only in the current design.
2. Out of the 32 Message objects available, 16 are kept aside for RX
purposes and the rest for TX purposes.
3. NAPI implementation is such that both the TX and RX paths function
in polling mode.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous patch "[PATCH 1/3] pch_can: fix 800k comms issue" is wrong.
I should have modified tseg1_min not tseg2_min.
This patch reverts tseg2_min to 1 and set tseg1_min to 2.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Randy Dunlap <randy.dunlap@oracle.com>
softing_cs.c uses kzalloc & kfree, so it needs to include linux/slab.h.
drivers/net/can/softing/softing_cs.c:234: error: implicit declaration of function 'kfree'
drivers/net/can/softing/softing_cs.c:271: error: implicit declaration of function 'kzalloc'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, in case reload pch_can,
pch_can not to be able to catch interrupt.
The cause is bus-master is not set in pch_can.
Thus, add enabling bus-master processing.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when rmmod pch_can, kernel failure occurs.
The cause is pci_iounmap executed before pch_can_reset.
Thus pci_iounmap moves after pch_can_reset.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, 800k comms fails since prop_seg set zero.
(EG20T PCH CAN register of prop_seg must be set more than 1)
To prevent prop_seg set to zero, change tseg2_min 1 to 2.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't allow everybody to set terminator via sysfs.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't allow everybody to write to mb0_id file.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Acked-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this dependency the softing driver will be buildable on s390,
where it fails.
Signed-Off-By: Chuck Ebbert <cebbert@redhat.com>
Acked-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the referenced project website to www.mictronics.de in the Kconfig
help text for the slcan driver.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to a chip bug (errata 50.2.6.3 & 50.3.5.3 in
"AT91SAM9263 Preliminary 6249H-ATARM-27-Jul-09") the contents of mailbox
0 may be send under certain conditions (even if disabled or in rx mode).
The workaround in the errata suggests not to use the mailbox and load it
with an unused identifier.
This patch implements the second part of the workaround. A sysfs entry
"mb0_id" is introduced. While the interface is down it can be used to
configure the can_id of mailbox 0. The default value id 0x7ff.
In order to use an extended can_id add the CAN_EFF_FLAG (0x80000000U)
to the can_id. Example:
- standard id 0x7ff:
echo 0x7ff > /sys/class/net/can0/mb0_id
- extended id 0x1fffffff:
echo 0x9fffffff > /sys/class/net/can0/mb0_id
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
For the Documentation-part:
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Due to a chip bug (errata 50.2.6.3 & 50.3.5.3 in
"AT91SAM9263 Preliminary 6249H-ATARM-27-Jul-09") the contents of mailbox
0 may be send under certain conditions (even if disabled or in rx mode).
The workaround in the errata suggests not to use the mailbox and load it
with a unused identifier.
This patch implements the first part of the workaround, it updates
AT91_MB_RX_NUM and AT91_MB_RX_FIRST (and the inline documentation)
so that mailbox 0 stays unused.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
This patch cleans up the usage of two macros which specify the mailbox
usage. AT91_MB_RX_FIRST and AT91_MB_RX_NUM define the first and the
number of RX mailboxes. The current driver uses these variables in an
unclean way; assuming that AT91_MB_RX_FIRST is 0;
This patch cleans up the usage of these macros, no longer assuming
AT91_MB_RX_FIRST == 0.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
This patch adds the driver that creates a platform:softing device
from a pcmcia_device
Note: the Kconfig indicates a dependency on the softing.ko driver,
but this is purely to make configuration intuitive. This driver will
work independent, but no CAN network devices appear until softing.ko is
loaded too.
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a driver for the platform:softing device.
This will create (up to) 2 CAN network devices from 1
platform:softing device
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using static const generally increases object text and decreases data size.
It also generally decreases overall object size.
Signed-off-by: Joe Perches <joe@perches.com>
Since this driver is implemented as NAPI,
netif_receive_skb must be used not netif_rx.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add setting TEC/REC statistics processing.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For reduce "if" condition, easy to read/understand the code,
optimize "if" condition in rx/tx processing.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, in case this driver is integrated as module, and when this
module is re-installed, no interrupts is to be occurred.
For the above issue, move MSI processing to open/release processing.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
