The end of an MMCONFIG region depends on the ending bus number, not on the
number of buses the region covers. We previously computed the wrong ending
address whenever the starting bus number was non-zero, e.g.,:
MMCONFIG for [bus 00-1f] at [mem 0xe0000000-0xe1ffffff] (base 0xe0000000)
MMCONFIG for [bus 20-3f] at [mem 0xe2000000-0xe1ffffff] (base 0xe0000000)
The correct regions are:
MMCONFIG for [bus 00-1f] at [mem 0xe0000000-0xe1ffffff] (base 0xe0000000)
MMCONFIG for [bus 20-3f] at [mem 0xe2000000-0xe3ffffff] (base 0xe0000000)
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch updates the defines for Intel devices in
include/linux/pci_ids.h, referenced in arch/x86/pci/irq.c and
drivers/i2c/busses/i2c-i801.c, reflecting approved legal branding, and
using fuller code-names for products under development.
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch adds the LPC Controller DeviceIDs for the Intel Patsburg PCH.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This configuration type override is for XO-1 only and must not happen
on XO-1.5.
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
akiphie points out that a.out core-dumps have that odd task struct
dumping that was never used and was never really a good idea (it goes
back into the mists of history, probably the original core-dumping
code). Just remove it.
Also do the access_ok() check on dump_write(). It probably doesn't
matter (since normal filesystems all seem to do it anyway), but he
points out that it's normally done by the VFS layer, so ...
[ I suspect that we should possibly do "vfs_write()" instead of
calling ->write directly. That also does the whole fsnotify and write
statistics thing, which may or may not be a good idea. ]
And just to be anal, do this all for the x86-64 32-bit a.out emulation
code too, even though it's not enabled (and won't currently even
compile)
Reported-by: akiphie <akiphie@lavabit.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: relax ioremap prohibition (309caa9) for -final and -stable
ARM: 6440/1: ep93xx: DMA: fix channel_disable
cpuimx27: fix i2c bus selection
cpuimx27: fix compile when ULPI is selected
ARM: 6435/1: Fix HWCAP_TLS flag for ARM11MPCore/Cortex-A9
ARM: 6436/1: AT91: Fix power-saving in idle-mode on 926T processors
ARM: fix section mismatch warnings in Versatile Express
ARM: 6412/1: kprobes-decode: add support for MOVW instruction
ARM: 6419/1: mmu: Fix MT_MEMORY and MT_MEMORY_NONCACHED pte flags
ARM: 6416/1: errata: faulty hazard checking in the Store Buffer may lead to data corruption
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
omap: iommu-load cam register before flushing the entry
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, numa: For each node, register the memory blocks actually used
x86, AMD, MCE thresholding: Fix the MCi_MISCj iteration order
x86, mce, therm_throt.c: Fix missing curly braces in error handling logic
... but produce a big warning about the problem as encouragement
for people to fix their drivers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When channel_disable() is called, it disables per channel interrupts and
waits until channels state becomes STATE_STALL, and then disables the
channel. Now, if the DMA transfer is disabled while the channel is in
STATE_NEXT we will not wait anything and disable the channel immediately.
This seems to cause weird data corruption for example in audio transfers.
Fix is to wait while we are in STATE_NEXT or STATE_ON and only then
disable the channel.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russ reported SGI UV is broken recently. He said:
| The SRAT table shows that memory range is spread over two nodes.
|
| SRAT: Node 0 PXM 0 100000000-800000000
| SRAT: Node 1 PXM 1 800000000-1000000000
| SRAT: Node 0 PXM 0 1000000000-1080000000
|
|Previously, the kernel early_node_map[] would show three entries
|with the proper node.
|
|[ 0.000000] 0: 0x00100000 -> 0x00800000
|[ 0.000000] 1: 0x00800000 -> 0x01000000
|[ 0.000000] 0: 0x01000000 -> 0x01080000
|
|The problem is recent community kernel early_node_map[] shows
|only two entries with the node 0 entry overlapping the node 1
|entry.
|
| 0: 0x00100000 -> 0x01080000
| 1: 0x00800000 -> 0x01000000
After looking at the changelog, Found out that it has been broken for a while by
following commit
|commit 8716273cae
|Author: David Rientjes <rientjes@google.com>
|Date: Fri Sep 25 15:20:04 2009 -0700
|
| x86: Export srat physical topology
Before that commit, register_active_regions() is called for every SRAT memory
entry right away.
Use nodememblk_range[] instead of nodes[] in order to make sure we
capture the actual memory blocks registered with each node. nodes[]
contains an extended range which spans all memory regions associated
with a node, but that does not mean that all the memory in between are
included.
Reported-by: Russ Anderson <rja@sgi.com>
Tested-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4CB27BDF.5000800@kernel.org>
Acked-by: David Rientjes <rientjes@google.com>
Cc: <stable@kernel.org> 2.6.33 .34 .35 .36
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The VMCB is reset whenever we receive a startup IPI, so Linux is setting
TSC back to zero happens very late in the boot process and destabilizing
the TSC. Instead, just set TSC to zero once at VCPU creation time.
Why the separate patch? So git-bisect is your friend.
Signed-off-by: Zachary Amsden <zamsden@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
On reset, VMCB TSC should be set to zero. Instead, code was setting
tsc_offset to zero, which passes through the underlying TSC.
Signed-off-by: Zachary Amsden <zamsden@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This fixes possible cases of not collecting valid error info in
the MCE error thresholding groups on F10h hardware.
The current code contains a subtle problem of checking only the
Valid bit of MSR0000_0413 (which is MC4_MISC0 - DRAM
thresholding group) in its first iteration and breaking out if
the bit is cleared.
But (!), this MSR contains an offset value, BlkPtr[31:24], which
points to the remaining MSRs in this thresholding group which
might contain valid information too. But if we bail out only
after we checked the valid bit in the first MSR and not the
block pointer too, we miss that other information.
The thing is, MC4_MISC0[BlkPtr] is not predicated on
MCi_STATUS[MiscV] or MC4_MISC0[Valid] and should be checked
prior to iterating over the MCI_MISCj thresholding group,
irrespective of the MC4_MISC0[Valid] setting.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: SAMSUNG: Add a workaround for get_clock() for serial driver
ARM: S5P: Bug fix on errors of build with CONFIG_PREEMPT_NONE
ARM: SAMSUNG: Fix build warnings because of unused codes
Define an _addr_lsb field in the mips and ia64 siginfo_ts, following
the asm-generic version. This just puts the field over padding.
This fixes a compilation problem introduced with a337fda.
Cc: ralf@linux-mips.org
Cc: tony.luck@intel.com
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recent clean of i.MX devices registration changed the i2C bus number
selected for our platform (Freescale start peripheral ID at 1, kernel
now start it at 0 so i.MX27's i2c 1 is kernel's i2c 0).
Without this fix, i2c is unusable on this platform.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
without this patch we get :
arch/arm/mach-imx/built-in.o: In function `eukrea_cpuimx27_init':
eukrea_mbimx27-baseboard.c:(.init.text+0x44c): undefined reference to `mxc_ulpi_access_ops'
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Commit 14eff18126 added proper
detection for ARM11MPCore/Cortex-A9 instead of detecting them
as ARMv7. However, it was missing the HWCAP_TLS flags.
HWCAP_TLS is needed if support for earlier ARMv6 is compiled
into the same kernel. Without HWCAP_TLS flags the userspace
won't work unless nosmp is specified:
Kernel panic - not syncing: Attempted to kill init!
CPU0: stopping
<c005d5e4>] (unwind_backtrace+0x0/0xec) from [<c004c2f8>] (do_IPI+0xfc/0x184)
<c004c2f8>] (do_IPI+0xfc/0x184) from [<c03f25bc>] (__irq_svc+0x9c/0x160)
Exception stack(0xc0565f80 to 0xc0565fc8)
5f80: 00000001 c05772a0 00000000 00003a61 c0564000 c05cf500 c003603c c0578600
5fa0: 80033ef0 410fc091 0000001f 00000000 00000000 c0565fc8 c00b91f8 c0057cb4
5fc0: 20000013 ffffffff
[<c03f25bc>] (__irq_svc+0x9c/0x160) from [<c0057cb4>] (default_idle+0x30/0x38)
[<c0057cb4>] (default_idle+0x30/0x38) from [<c005829c>] (cpu_idle+0x9c/0xf8)
[<c005829c>] (cpu_idle+0x9c/0xf8) from [<c0008d48>] (start_kernel+0x2a4/0x300)
[<c0008d48>] (start_kernel+0x2a4/0x300) from [<80008084>] (0x80008084)
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
According to Atmel, their 926T processors (AT91 post RM9200) requires
'Wait for Interrupt' mode be entered right after disabling the processor clock
in order to minimise current consumption when idle, so do both provided we're
not running on a 920T (an RM9200).
Furthermore, get rid of the #ifndef CONFIG_DEBUG_KERNEL, since arch_idle()
can be turned off completely with the kernel parameter 'nohlt'.
Cc: Andrew Victor <avictor.za@gmail.com>
Signed-off-by: Anders Larsen <al@alarsen.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When the feature PTS is not supported by CPU, the sysfile
package_power_limit_count for package should not be
generated.
This patch is used for fixing missing { and }.
The patch is not complete as there are other error handling
problems in this function - but that can wait until the
merge window.
Signed-off-by: Jin Dongming <jin.dongming@np.css.fujitsu.com>
Reviewed-by: Fenghua Yu <fenghua.yu@initel.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: Brown Len <len.brown@intel.com>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Cc: lm-sensors@lm-sensors.org <lm-sensors@lm-sensors.org>
LKML-Reference: <4C7625D1.4060201@np.css.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Serial drivers call get_clock() very early, before platform bus
has been set up, this requires a special check to let them get
a proper clock. Without this patch, a serial console is broken
on S5PV310 and S5PC210 boards.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: fix coding-style]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
This patch adds header <linux/sched.h> into the below files for build with
CONFIG_PREEMPT_NONE.
arch/arm/mach-s5p6440/cpu.c
arch/arm/mach-s5p6442/cpu.c
arch/arm/mach-s5pc100/cpu.c
arch/arm/mach-s5pv210/cpu.c
Following is error message of in case of s5pv210_defconfig with CONFIG_PREEMPT_NONE.
arch/arm/mach-s5pv210/cpu.c:91: error: implicit declaration of function 'need_resched'
Signed-off-by: SeungChull Suh <sc.suh@samsung.com>
[kgene.kim@samsung.com: removed mach-s5p64x0/cpu.c]
[kgene.kim@samsung.com: added fix mach-s5p6440/cpu.c]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch removes following unused codes for removing build warnings.
arch/arm/plat-samsung/adc.c:438: warning: unused variable 'flags'
arch/arm/mach-s5pv210/clock.c:176: warning: 's5pv210_clk_ip4_ctrl' defined but not used
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus:
MIPS: Octeon: Place cnmips_cu2_setup in __init memory.
MIPS: Don't place cu2 notifiers in __cpuinitdata
MIPS: Calculate VMLINUZ_LOAD_ADDRESS based on the length of vmlinux.bin
MIPS: Alchemy: Resolve prom section mismatches
MIPS: Fix syscall 64 bit number comments.
MIPS: Hookup fanotify_init, fanotify_mark, and prlimit64 syscalls.
MIPS: TX49xx: Rename ARCH_KMALLOC_MINALIGN to ARCH_DMA_MINALIGN
MIPS: N32: Fix getdents64 syscall for n32
MIPS: Remove pr_<level> uses of KERN_<level>
MIPS: PNX8550: Sort out machine halt, restart and powerdown functions.
MIPS: GIC: Remove dependencies from Malta files.
MIPS: Kconfig: Fix and clarify kconfig help text for VSMP and SMTC.
MIPS: DMA: Fix computation of DMA flags from device's coherent_dma_mask.
MIPS: Audit: Fix hang in entry.S.
MIPS: Document why RELOC_HIDE is there.
MIPS: Octeon: Determine if helper needs to be built
MIPS: Use generic atomic64 for 32-bit kernels
MIPS: RM7000: Symbol should be static
MIPS: kspd: Adjust confusing if indentation
MIPS: Fix a typo.
* 'v2.6.36-rc6-urgent-fixes' of git://xenbits.xen.org/people/sstabellini/linux-pvhvm:
xen: do not initialize PV timers on HVM if !xen_have_vector_callback
xen: do not set xenstored_ready before xenbus_probe on hvm
Since powerpc uses -Werror on arch powerpc, the build was broken like
this:
cc1: warnings being treated as errors
arch/powerpc/kernel/module.c: In function 'module_finalize':
arch/powerpc/kernel/module.c:66: error: unused variable 'err'
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf trace scripting: Fix extern struct definitions
perf ui hist browser: Fix segfault on 'a' for annotate
perf tools: Fix build breakage
perf, x86: Handle in flight NMIs on P4 platform
oprofile, ARM: Release resources on failure
oprofile: Add Support for Intel CPU Family 6 / Model 29
With all the recent module loading cleanups, we've minimized the code
that sits under module_mutex, fixing various deadlocks and making it
possible to do most of the module loading in parallel.
However, that whole conversion totally missed the rather obscure code
that adds a new module to the list for BUG() handling. That code was
doubly obscure because (a) the code itself lives in lib/bugs.c (for
dubious reasons) and (b) it gets called from the architecture-specific
"module_finalize()" rather than from generic code.
Calling it from arch-specific code makes no sense what-so-ever to begin
with, and is now actively wrong since that code isn't protected by the
module loading lock any more.
So this commit moves the "module_bug_{finalize,cleanup}()" calls away
from the arch-specific code, and into the generic code - and in the
process protects it with the module_mutex so that the list operations
are now safe.
Future fixups:
- move the module list handling code into kernel/module.c where it
belongs.
- get rid of 'module_bug_list' and just use the regular list of modules
(called 'modules' - imagine that) that we already create and maintain
for other reasons.
Reported-and-tested-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Adrian Bunk <bunk@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The flush_iotlb_page is not loading the cam register before flushing
the cam entry. This causes wrong entry to be flushed out from the TLB, and
if the entry happens to be a locked TLB entry it would lead to MMU faults.
The fix is to load the cam register with the address to be flushed before
flushing the TLB entry.
Signed-off-by: Hari Kanigeri <h-kanigeri2@ti.com>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
if !xen_have_vector_callback do not initialize PV timer unconditionally
because we still don't know how many cpus are available and if there is
more than one we won't be able to receive the timer interrupts on
cpu > 0.
This patch fixes an hang at boot when Xen does not support vector
callbacks and the guest has multiple vcpus.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Jeremy Fitzhardinge <jeremy@goop.org>
WARNING: vmlinux.o(.text+0xbf30): Section mismatch in reference from the function v2m_timer_init() to the function .init.text:sp804_clocksource_init()
The function v2m_timer_init() references
the function __init sp804_clocksource_init().
This is often because v2m_timer_init lacks a __init
annotation or the annotation of sp804_clocksource_init is wrong.
WARNING: vmlinux.o(.text+0xbf3c): Section mismatch in reference from the function v2m_timer_init() to the function .init.text:sp804_clockevents_init()
The function v2m_timer_init() references
the function __init sp804_clockevents_init().
This is often because v2m_timer_init lacks a __init
annotation or the annotation of sp804_clockevents_init is wrong.
WARNING: vmlinux.o(.text+0xc524): Section mismatch in reference from the function ct_ca9x4_init() to the function .init.text:l2x0_init()
The function ct_ca9x4_init() references
the function __init l2x0_init().
This is often because ct_ca9x4_init lacks a __init
annotation or the annotation of l2x0_init is wrong.
WARNING: vmlinux.o(.text+0xc530): Section mismatch in reference from the function ct_ca9x4_init() to the function .init.text:clkdev_add_table()
The function ct_ca9x4_init() references
the function __init clkdev_add_table().
This is often because ct_ca9x4_init lacks a __init
annotation or the annotation of clkdev_add_table is wrong.
WARNING: vmlinux.o(.text+0xc578): Section mismatch in reference from the function ct_ca9x4_init() to the (unknown reference) .init.data:(unknown)
The function ct_ca9x4_init() references
the (unknown reference) __initdata (unknown).
This is often because ct_ca9x4_init lacks a __initdata
annotation or the annotation of (unknown) is wrong.
Fix these by making ct_ca9x4_init() and v2m_timer_init() both __init.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The MOVW instruction moves a 16-bit immediate into the bottom halfword
of the destination register.
This patch ensures that kprobes leaves the 16-bit immediate intact, rather
than assume a 12-bit immediate and mask out the upper 4 bits.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The commit f1a2481c0 sets up the default flags for MT_MEMORY and
MT_MEMORY_NONCACHED memory types. L_PTE_USER flag is wrongly
set as default for these entries so remove it. Also adding
the 'L_PTE_WRITE' flag so that these pages become read-write
instead of just being read-only
[this stops them being exposed to userspace, which is the main
concern here --rmk]
Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On the r2p0, r2p1 and r2p2 versions of the Cortex-A9, data corruption
can occur under very rare conditions due to a store buffer optimisation.
This workaround sets a bit in the diagnostic register of the Cortex-A9,
disabling the optimisation and preventing the problem from occurring.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
vlan: dont drop packets from unknown vlans in promiscuous mode
Phonet: Correct header retrieval after pskb_may_pull
um: Proper Fix for f25c80a4: remove duplicate structure field initialization
ip_gre: Fix dependencies wrt. ipv6.
net-2.6: SYN retransmits: Add new parameter to retransmits_timed_out()
iwl3945: queue the right work if the scan needs to be aborted
mac80211: fix use-after-free
The notifiers may be called at any time, so the notifier_block cannot
be in init memory.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1592/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix VMLINUZ_LOAD_ADDRESS calculation to be based on the length of
vmlinux.bin, the actual uncompressed kernel binary.
Previously it was based on the length of KBUILD_IMAGE (the unstripped ELF
vmlinux), which is bigger than vmlinux.bin. As a result, vmlinuz was
loaded into a memory address higher then actually needed - a problem for
small memory platforms.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
To: linux-mips@linux-mips.org
Cc: alex@digriz.org.uk
Cc: manuel.lauss@googlemail.com
Cc: sam@ravnborg.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1564/
Acked-by: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The function prom_init_cmdline() references the variable __initdata
arcs_cmdline.
The function prom_get_ethernet_addr() references the variable __initdata
arcs_cmdline.
Annotate prom_init_cmdline() as __init, unexport and annotate
prom_get_ethernet_addr() since it's no longer called from within
driver code.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/1547/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
No rubbish printks - those belong to userspace. The halt function now
actually halts the system and the poweroff function was deleted because
it didn't actually power down the system.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
