Commit Graph

56 Commits

Author SHA1 Message Date
Alexandre Torgue
8eb2dfee9f pinctrl: stm32: add lock mechanism for irqmux selection
GPIOs are split between several banks (A, B, ...) and each bank can have
up to 16 lines. Those GPIOs could be used as interrupt lines thanks to
exti lines. As there are only 16 exti lines, a mux is used to select which
gpio line is connected to which exti line. Mapping is done as follow:

-A0, B0, C0.. -->exti_line_0 (X0 selected by mux_0)
-A1, B1, C1.. -->exti_line_1 (X1 selected by mux_1)
...

This patch adds a protection to avoid overriding on mux_n for exti_line_n.

Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-05-24 13:25:34 +02:00
Alexandre Torgue
a45623ddd0 pinctrl: stm32: Enable suspend/resume for stm32mp157c SoC
Apply suspend/resume management for stm32mp157c MPU.

Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-05-24 13:21:45 +02:00
Alexandre Torgue
e2f3cf18c3 pinctrl: stm32: add suspend/resume management
During power sequence, GPIO hardware registers could be lost if the power
supply is switched off. Each device using pinctrl API is in charge of
managing pins during suspend/resume sequences. But for pins used as gpio or
irq stm32 pinctrl driver has to save the hardware configuration.

Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-05-24 13:21:15 +02:00
Fabien Dessenne
d86f4d71e4 pinctrl: stm32: check irq controller availability at probe
It is not guaranteed that the IRQ controller driver is probed before
the pin controller driver gets probed.
Considering this, check for the irq domain availability during probe
and return EPROBE_DEFER if needed.

Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-05-03 07:53:13 +01:00
Alexandre Torgue
a7672c4a3f pinctrl: stm32: align stm32mp157 pin names
Align pins names with names provided in official stm32mp157 datasheet
available on st.com.

Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-04-23 10:47:06 +02:00
Alexandre Torgue
6918bf4373 pinctrl: stm32: add package information for stm32mp157c
This patch adds four new packages support for stm32mp157c die:

STM32MP_PKG_AA: LFBGA448 (18*18), 176 IOs
STM32MP_PKG_AB: LFBGA354 (16*16), 98 IOs
STM32MP_PKG_AC: TFBGA361 (12*12), 148 IOs
STM32MP_PKG_AD: TFBGA257 (10*10), 98 IOs

Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-04-23 10:47:03 +02:00
Alexandre Torgue
cc528862d9 pinctrl: stm32: introduce package support
A same SoC can be available in several packages. Differences between
packages are only the numbers of available balls. In order not to write
a driver for each new package, same driver (ex: pinctrl-stm32mp157.c) will
be used. This patch introduces the "package" property for each pin. So on a
same driver, it will be possible to indicate on which package the pin is
available. The package information will be got from the device tree.

Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-04-23 10:46:58 +02:00
Alexandre Torgue
e003ec6aa9 pinctrl: stm32: return error upon hwspinlock failure
Return error to the caller when the hwspinlock can't get locked.

Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-02-20 10:41:09 +01:00
Alexandre Torgue
cd8c9b5a49 pinctrl: stm32: fix memory leak issue
configs is allocated by pinconf_generic_parse_dt_config(),
pinctrl_utils_add_map_configs() duplicates configs so it can and has to
be freed to prevent memory leaks.

Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-02-20 10:40:39 +01:00
Benjamin Gaignard
97cfb6cd34 pinctrl: stm32: protect configuration registers with a hwspinlock
If a hwspinlock if defined in device tree use it to protect
configuration registers.

Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-11-19 13:17:46 +01:00
Rob Herring
94f4e54cec pinctrl: Convert to using %pOFn instead of device_node.name
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Dong Aisheng <aisheng.dong@nxp.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@bootlin.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Barry Song <baohua@kernel.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: linux-gpio@vger.kernel.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-amlogic@lists.infradead.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-omap@vger.kernel.org
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-08-29 14:05:36 +02:00
Ludovic Barre
2e25a9cbdf pinctrl: stm32: add syscfg mask parameter
This patch adds mask parameter to define IRQ mux field.
This field could vary depend of IRQ mux selection register.
To avoid backward compatibility, the drivers set
the legacy value by default.

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-07-29 22:14:59 +02:00
Alexandre Torgue
17cf082d6d pinctrl: stm32: check node status before new gpio bank registering
Register a new GPIO bank only if GPIO bank node is enabled. This patch also
adds checks on ranges which are defined only if a bank is registered.

Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-07-29 22:03:33 +02:00
Alexandre Torgue
3b8283f007 pinctrl: stm32: fix bank io port number
In case the exti line is not in line with the bank number (that is the case
when there is an hole between two banks, for example GPIOK and then GPIOZ),
use "st,bank-ioport" DT property to get the right exti line.

Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-07-29 22:01:34 +02:00
Ludovic Barre
c12fcfb12e pinctrl/stm32: Add irq_eoi for stm32gpio irqchip
-Parent domain of stm32gpio evolves to hierarchy domain
 and could have a handle_fasteoi_irq. So an irq_eoi parent callback
 is needed for children.
-Replace space by tabulation.

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2018-05-24 12:38:22 +01:00
Masahiro Yamada
86822c2f3a pinctrl: stm32: add 'depends on HAS_IOMEM' to fix unmet dependency
These configs select MFD_SYSCON, but do not depend on HAS_IOMEM.

Compile testing on architecture without HAS_IOMEM causes "unmet
direct dependencies" in Kconfig phase.

Detected by "make ARCH=score allyesconfig".

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-23 04:04:40 +01:00
Radoslaw Pietrzyk
430a2a5945 pinctrl: stm32: Optimizes and enhances stm32gpio irqchip
- removes unneeded irq_chip.irq_eoi callback
- adds irq_chip.irq_set_wake callback for possible
  in the future GPIO wakeup
- adds irq_chip.irq_ack callback

Signed-off-by: Radoslaw Pietrzyk <radoslaw.pietrzyk@gmail.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-02 08:40:31 +01:00
Linus Torvalds
ef991796be This is the bulk of pin control changes for the v4.16 kernel cycle:
Core changes:
 
 - After lengthy discussions and partly due to my ignorance, we have
   merged a patch making pinctrl_force_default() and pinctrl_force_sleep()
   reprogram the states into the hardware of any hogged pins, even
   if they are already in the desired state. This only apply to hogged
   pins since groups of pins owned by drivers need to be managed by
   each driver, lest they could not do things like runtime PM and
   put pins to sleeping state even if the system as a whole is not
   in sleep.
 
 New drivers:
 
 - New driver for the Microsemi Ocelot SoC. This is used in ethernet
   switches.
 
 - The X-Powers AXP209 GPIO driver was extended to also deal with pin
   control and moved over from the GPIO subsystem. This circuit is
   a mixed-mode integrated circuit which is part of AllWinner designs.
 
 - New subdriver for the Qualcomm MSM8998 SoC, core of a high end
   mobile devices (phones) chipset.
 
 - New subdriver for the ST Microelectronics STM32MP157 MPU and
   STM32F769 MCU from the STM32 family.
 
 - New subdriver for the MediaTek MT7622 SoC. This is used for routers,
   repeater, gateways and such network infrastructure.
 
 - New subdriver for the NXP (former Freescale) i.MX 6ULL. This SoC has
   multimedia features and target "smart devices", I guess in-car
   entertainment, in-flight entertainment, industrial control panels etc.
 
 General improvements:
 
 - Incremental improvements on the SH-PFC subdrivers for things like
   the CAN bus.
 
 - Enable the glitch filter on Baytrail GPIOs used for interrupts.
 
 - Proper handling of pins to GPIO ranges on the Semtec SX150X
 
 - An IRQ setup ordering fix on MCP23S08.
 
 - A good set of janitorial coding style fixes.
 -----BEGIN PGP SIGNATURE-----
 
 iQIcBAABAgAGBQJadGEKAAoJEEEQszewGV1zA4QQALs8edxhv4qV5vm50mTdrO3n
 QtRhJNb53j6MIKtjFnazMvh6MXRIP+08SyX9sDLi5AxINIVuyQh3mrcB6Zc9zN58
 +6jFFOIbfm5E8by4n3wnKm3F/WAbNBZph9eT2Rn3cDv9o9hQbyNJ50sQkQMCjd9X
 WGR353c3OL4zb3vU8t72G/RPYUY1w1SkG9bGzRuSif8LawDcN6v6MMo2XhZA6RqM
 3qYIG29vJ1n0weggUIBeSAJIzk4eMwcoWCbVWxhns5JGxw5VPES1zbSp1D+mbzRC
 01i5Pt/gD+cWN/Kk/zKIMo1OqLAl+uLr6hzepj6W+5wu9CcQz/BgvRx7HUqnqgyh
 S8cN4AOgWmW+T75pHypd1WVic3q0RCXkFY8jjHpCATDY+Z+js0lZRs3y4DBiJ2ys
 DMVBeumDINKqaZ6aLH6lVkm+SxXOUy143arQQIzi0/F7fAp68i+9ofIO8B5smEmd
 0S+3sT0sO5QXVgZJ0t0iGUUG5irXi8XtF5qvRmuFZUe0OLGgKX20oCdC0pH0WU4M
 OZO1Bvb8vmn1tddogO2WlHeg6amWdwxtDuBsLRO3YILLu3jwPjhNqNmErXzXEmWt
 TY9l2M1uQmoJibNpmTjOzSfj4OtUHMwkDrFRJHAcUPcKwdEy4MyzFL16ATnIwgY9
 AmyMLNWJd8Wazgc6BK6w
 =gLY/
 -----END PGP SIGNATURE-----

Merge tag 'pinctrl-v4.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl

Pull pin control updates from Linus Walleij:
 "This is the bulk of pin control changes for the v4.16 kernel cycle.
  Like with GPIO it is actually a bit calm this time.

  Core changes:

   - After lengthy discussions and partly due to my ignorance, we have
     merged a patch making pinctrl_force_default() and
     pinctrl_force_sleep() reprogram the states into the hardware of any
     hogged pins, even if they are already in the desired state.

     This only apply to hogged pins since groups of pins owned by
     drivers need to be managed by each driver, lest they could not do
     things like runtime PM and put pins to sleeping state even if the
     system as a whole is not in sleep.

  New drivers:

   - New driver for the Microsemi Ocelot SoC. This is used in ethernet
     switches.

   - The X-Powers AXP209 GPIO driver was extended to also deal with pin
     control and moved over from the GPIO subsystem. This circuit is a
     mixed-mode integrated circuit which is part of AllWinner designs.

   - New subdriver for the Qualcomm MSM8998 SoC, core of a high end
     mobile devices (phones) chipset.

   - New subdriver for the ST Microelectronics STM32MP157 MPU and
     STM32F769 MCU from the STM32 family.

   - New subdriver for the MediaTek MT7622 SoC. This is used for
     routers, repeater, gateways and such network infrastructure.

   - New subdriver for the NXP (former Freescale) i.MX 6ULL. This SoC
     has multimedia features and target "smart devices", I guess in-car
     entertainment, in-flight entertainment, industrial control panels
     etc.

  General improvements:

   - Incremental improvements on the SH-PFC subdrivers for things like
     the CAN bus.

   - Enable the glitch filter on Baytrail GPIOs used for interrupts.

   - Proper handling of pins to GPIO ranges on the Semtec SX150X

   - An IRQ setup ordering fix on MCP23S08.

   - A good set of janitorial coding style fixes"

* tag 'pinctrl-v4.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (102 commits)
  pinctrl: mcp23s08: fix irq setup order
  pinctrl: Forward declare struct device
  pinctrl: sunxi: Use of_clk_get_parent_count() instead of open coding
  pinctrl: stm32: add STM32F769 MCU support
  pinctrl: sx150x: Add a static gpio/pinctrl pin range mapping
  pinctrl: sx150x: Register pinctrl before adding the gpiochip
  pinctrl: sx150x: Unregister the pinctrl on release
  pinctrl: ingenic: Remove redundant dev_err call in ingenic_pinctrl_probe()
  pinctrl: sprd: Use seq_putc() in sprd_pinconf_group_dbg_show()
  pinctrl: pinmux: Use seq_putc() in pinmux_pins_show()
  pinctrl: abx500: Use seq_putc() in abx500_gpio_dbg_show()
  pinctrl: mediatek: mt7622: align error handling of mtk_hw_get_value call
  pinctrl: mediatek: mt7622: fix potential uninitialized value being returned
  pinctrl: uniphier: refactor drive strength get/set functions
  pinctrl: imx7ulp: constify struct imx_cfg_params_decode
  pinctrl: imx: constify struct imx_pinctrl_soc_info
  pinctrl: imx7d: simplify imx7d_pinctrl_probe
  pinctrl: imx: use struct imx_pinctrl_soc_info as a const
  pinctrl: sunxi-pinctrl: fix pin funtion can not be match correctly.
  pinctrl: qcom: Add msm8998 pinctrl driver
  ...
2018-02-02 14:22:53 -08:00
Alexandre Torgue
f90160fc95 pinctrl: stm32: add STM32F769 MCU support
This patch which adds STM32F769 pinctrl and GPIO support, relies on the
generic STM32 pinctrl driver.

Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Acked-by: Patrice CHOTARD <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-22 09:28:08 +01:00
Thomas Gleixner
702cb0a028 genirq/irqdomain: Rename early argument of irq_domain_activate_irq()
The 'early' argument of irq_domain_activate_irq() is actually used to
denote reservation mode. To avoid confusion, rename it before abuse
happens.

No functional change.

Fixes: 7249164346 ("genirq/irqdomain: Update irq_domain_ops.activate() signature")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Alexandru Chirvasitu <achirvasub@gmail.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Dou Liyang <douly.fnst@cn.fujitsu.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Mikael Pettersson <mikpelinux@gmail.com>
Cc: Josh Poulson <jopoulso@microsoft.com>
Cc: Mihai Costache <v-micos@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-pci@vger.kernel.org
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Dexuan Cui <decui@microsoft.com>
Cc: Simon Xiao <sixiao@microsoft.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jork Loeser <Jork.Loeser@microsoft.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: devel@linuxdriverproject.org
Cc: KY Srinivasan <kys@microsoft.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Sakari Ailus <sakari.ailus@intel.com>,
Cc: linux-media@vger.kernel.org
2017-12-29 21:13:04 +01:00
Ludovic Barre
4ef4cc13ea pinctrl: stm32: Add STM32MP157 MPU support
This driver consists of 2 controllers due to a hole in mapping:
-1 controller for GPIO bankA to K.
-1 controller for GPIO bankZ.

Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-12-20 08:36:22 +01:00
Benjamin Gaignard
e7c0e2f372 pinctrl: stm32: Fix copyright
Uniformize STMicroelectronics copyrights header
Add SPDX identifier

Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-12-02 16:23:08 +01:00
Linus Torvalds
b630a23a73 This is the bulk of pin control changes for the v4.15
kernel cycle:
 
 Core:
 
 - The pin control Kconfig entry PINCTRL is now turned into
   a menuconfig option. This obviously has the implication of
   making the subsystem menu visible in menuconfig. This is
   happening because of two things:
 
   - Intel have started to deploy and depend on pin controllers
     in a way that is affecting users directly. This happens
     on the highly integrated laptop chipsets named after
     geographical places: baytrail, broxton, cannonlake,
     cedarfork, cherryview, denverton, geminilake, lewisburg,
     merrifield, sunrisepoint... It started a while back and
     now it is ever more evident that this is crucial
     infrastructure for x86 laptops and not an embedded
     obscurity anymore. Users need to be aware.
 
   - Pin control expanders on I2C and SPI that are
     arch-agnostic. Currently Semtech SX150X and Microchip
     MCP28x08 but more are expected. Users will have to be
     able to configure these in directly for their set-up.
 
 - Just go and select GPIOLIB now that we made sure that
   GPIOLIB is a very vanilla subsystem. Do not depend on
   it, if we need it, select it.
 
 - Exposing the pin control subsystem in menuconfig uncovered
   a bunch of obscure bugs that are now hopefully fixed,
   all more or less pertaining to Blackfin.
 
 - Unified namespace for cross-calls between pin control and
   GPIO.
 
 - New support for clock skew/delay generic DT bindings
   and generic pin config options for this.
 
 - Minor documentation improvements.
 
 Various:
 
 - The Renesas SH-PFC pin controller has evolved a lot. It seems
   Renesas are churning out new SoCs by the minute.
 
 - A bunch of non-critical fixes for the Rockchip driver.
 
 - Improve the use of library functions instead of open coding.
 
 - Support the MCP28018 variant in the MCP28x08 driver.
 
 - Static constifying.
 -----BEGIN PGP SIGNATURE-----
 
 iQIcBAABAgAGBQJaDV9TAAoJEEEQszewGV1zf0AQAIlHxM8B0mJPOFv7WdPIHs8j
 GSGAPv0rPobdgZI8vegosIQmAiry5jjaHP6VGOrK5n8FRxfBLd89NLT7dgK7J9Yx
 tYcQRQn1/MqZKaIjWWgTes3okEr9s77Of3aWkA9gyvBjTGoo2hu8BTwZOYuPrIPP
 aYcI7VR0VbTe7FQR1QRtKBXnBTXfznF1j5ckKNY4ahgIPcUgxyh6EA1E61rDorLK
 gvwwzoBqIKQAcnapgarF7YOJjoE0i7ZoSlhL0b0nvhcgolyK/zLN4xujLcTGPeTJ
 hQwe7LhxtvtmJmu0jRMuetDLFT52d6eq8ttyFBMULkgRzcgMv6GZZXUy4k92t7ZT
 F2DRbAjyAlxkhUhQ8BORzEXwfWYITt1M49jWQqugdDR2fV/MAlF8motOkVBl73iS
 zHIQ/ZDcAD+PlwTHiDyDOUxj7qyDs2MkTLTzfXc0koOQZOqskDHQ1dIf3UzLzZ9S
 /dx339/ejwP73E0lzOsanhianfonqWZ3Apn3aRG18uqCt2+eHySWpxyRANuOlBZI
 czERg+47wDfng24xyuH0EElgbS5G0Bt1lT5zLVLdFEvoLmcBHVKqaCkiuvYXOjVM
 GyMRvQPiJbhT6qiJ+aSP8t/utl1aUhXQLtrUnXxu8qv9tQ6jgmqiQd9855Uvrzb0
 ZR2wyNc2jtWzwCfrkWjt
 =kj/b
 -----END PGP SIGNATURE-----

Merge tag 'pinctrl-v4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl

Pull pin control updates from Linus Walleij:
 "This is the bulk of pin control changes for the v4.15 kernel cycle:

  Core:

   - The pin control Kconfig entry PINCTRL is now turned into a
     menuconfig option. This obviously has the implication of making the
     subsystem menu visible in menuconfig. This is happening because of
     two things:

      (a) Intel have started to deploy and depend on pin controllers in
          a way that is affecting users directly. This happens on the
          highly integrated laptop chipsets named after geographical
          places: baytrail, broxton, cannonlake, cedarfork, cherryview,
          denverton, geminilake, lewisburg, merrifield, sunrisepoint...
          It started a while back and now it is ever more evident that
          this is crucial infrastructure for x86 laptops and not an
          embedded obscurity anymore. Users need to be aware.

      (b) Pin control expanders on I2C and SPI that are arch-agnostic.
          Currently Semtech SX150X and Microchip MCP28x08 but more are
          expected. Users will have to be able to configure these in
          directly for their set-up.

   - Just go and select GPIOLIB now that we made sure that GPIOLIB is a
     very vanilla subsystem. Do not depend on it, if we need it, select
     it.

   - Exposing the pin control subsystem in menuconfig uncovered a bunch
     of obscure bugs that are now hopefully fixed, all more or less
     pertaining to Blackfin.

   - Unified namespace for cross-calls between pin control and GPIO.

   - New support for clock skew/delay generic DT bindings and generic
     pin config options for this.

   - Minor documentation improvements.

  Various:

   - The Renesas SH-PFC pin controller has evolved a lot. It seems
     Renesas are churning out new SoCs by the minute.

   - A bunch of non-critical fixes for the Rockchip driver.

   - Improve the use of library functions instead of open coding.

   - Support the MCP28018 variant in the MCP28x08 driver.

   - Static constifying"

* tag 'pinctrl-v4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (91 commits)
  pinctrl: gemini: Fix missing pad descriptions
  pinctrl: Add some depends on HAS_IOMEM
  pinctrl: samsung/s3c24xx: add CONFIG_OF dependency
  pinctrl: gemini: Fix GMAC groups
  pinctrl: qcom: spmi-gpio: Add pmi8994 gpio support
  pinctrl: ti-iodelay: remove redundant unused variable dev
  pinctrl: max77620: Use common error handling code in max77620_pinconf_set()
  pinctrl: gemini: Implement clock skew/delay config
  pinctrl: gemini: Use generic DT parser
  pinctrl: Add skew-delay pin config and bindings
  pinctrl: armada-37xx: Add edge both type gpio irq support
  pinctrl: uniphier: remove eMMC hardware reset pin-mux
  pinctrl: rockchip: Add iomux-route switching support for rk3288
  pinctrl: intel: Add Intel Cedar Fork PCH pin controller support
  pinctrl: intel: Make offset to interrupt status register configurable
  pinctrl: sunxi: Enforce the strict mode by default
  pinctrl: sunxi: Disable strict mode for old pinctrl drivers
  pinctrl: sunxi: Introduce the strict flag
  pinctrl: sh-pfc: Save/restore registers for PSCI system suspend
  pinctrl: sh-pfc: r8a7796: Use generic IOCTRL register description
  ...
2017-11-16 10:57:11 -08:00
Linus Torvalds
670310dfba Merge branch 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq core updates from Thomas Gleixner:
 "A rather large update for the interrupt core code and the irq chip drivers:

   - Add a new bitmap matrix allocator and supporting changes, which is
     used to replace the x86 vector allocator which comes with separate
     pull request. This allows to replace the convoluted nested loop
     allocation function in x86 with a facility which supports the
     recently added property of managed interrupts proper and allows to
     switch to a best effort vector reservation scheme, which addresses
     problems with vector exhaustion.

   - A large update to the ARM GIC-V3-ITS driver adding support for
     range selectors.

   - New interrupt controllers:
       - Meson and Meson8 GPIO
       - BCM7271 L2
       - Socionext EXIU

     If you expected that this will stop at some point, I have to
     disappoint you. There are new ones posted already. Sigh!

   - STM32 interrupt controller support for new platforms.

   - A pile of fixes, cleanups and updates to the MIPS GIC driver

   - The usual small fixes, cleanups and updates all over the place.
     Most visible one is to move the irq chip drivers Kconfig switches
     into a separate Kconfig menu"

* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
  genirq: Fix type of shifting literal 1 in __setup_irq()
  irqdomain: Drop pointless NULL check in virq_debug_show_one
  genirq/proc: Return proper error code when irq_set_affinity() fails
  irq/work: Use llist_for_each_entry_safe
  irqchip: mips-gic: Print warning if inherited GIC base is used
  irqchip/mips-gic: Add pr_fmt and reword pr_* messages
  irqchip/stm32: Move the wakeup on interrupt mask
  irqchip/stm32: Fix initial values
  irqchip/stm32: Add stm32h7 support
  dt-bindings/interrupt-controllers: Add compatible string for stm32h7
  irqchip/stm32: Add multi-bank management
  irqchip/stm32: Select GENERIC_IRQ_CHIP
  irqchip/exiu: Add support for Socionext Synquacer EXIU controller
  dt-bindings: Add description of Socionext EXIU interrupt controller
  irqchip/gic-v3-its: Fix VPE activate callback return value
  irqchip: mips-gic: Make IPI bitmaps static
  irqchip: mips-gic: Share register writes in gic_set_type()
  irqchip: mips-gic: Remove gic_vpes variable
  irqchip: mips-gic: Use num_possible_cpus() to reserve IPIs
  irqchip: mips-gic: Configure EIC when CPUs come online
  ...
2017-11-13 17:33:11 -08:00
Greg Kroah-Hartman
b24413180f License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier.  The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
 - file had no licensing information it it.
 - file was a */uapi/* one with no licensing information in it,
 - file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne.  Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed.  Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
 - Files considered eligible had to be source code files.
 - Make and config files were included as candidates if they contained >5
   lines of source
 - File already had some variant of a license header in it (even if <5
   lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

 - when both scanners couldn't find any license traces, file was
   considered to have no license information in it, and the top level
   COPYING file license applied.

   For non */uapi/* files that summary was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0                                              11139

   and resulted in the first patch in this series.

   If that file was a */uapi/* path one, it was "GPL-2.0 WITH
   Linux-syscall-note" otherwise it was "GPL-2.0".  Results of that was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0 WITH Linux-syscall-note                        930

   and resulted in the second patch in this series.

 - if a file had some form of licensing information in it, and was one
   of the */uapi/* ones, it was denoted with the Linux-syscall-note if
   any GPL family license was found in the file or had no licensing in
   it (per prior point).  Results summary:

   SPDX license identifier                            # files
   ---------------------------------------------------|------
   GPL-2.0 WITH Linux-syscall-note                       270
   GPL-2.0+ WITH Linux-syscall-note                      169
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause)    21
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause)    17
   LGPL-2.1+ WITH Linux-syscall-note                      15
   GPL-1.0+ WITH Linux-syscall-note                       14
   ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause)    5
   LGPL-2.0+ WITH Linux-syscall-note                       4
   LGPL-2.1 WITH Linux-syscall-note                        3
   ((GPL-2.0 WITH Linux-syscall-note) OR MIT)              3
   ((GPL-2.0 WITH Linux-syscall-note) AND MIT)             1

   and that resulted in the third patch in this series.

 - when the two scanners agreed on the detected license(s), that became
   the concluded license(s).

 - when there was disagreement between the two scanners (one detected a
   license but the other didn't, or they both detected different
   licenses) a manual inspection of the file occurred.

 - In most cases a manual inspection of the information in the file
   resulted in a clear resolution of the license that should apply (and
   which scanner probably needed to revisit its heuristics).

 - When it was not immediately clear, the license identifier was
   confirmed with lawyers working with the Linux Foundation.

 - If there was any question as to the appropriate license identifier,
   the file was flagged for further research and to be revisited later
   in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.  The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
 - a full scancode scan run, collecting the matched texts, detected
   license ids and scores
 - reviewing anything where there was a license detected (about 500+
   files) to ensure that the applied SPDX license was correct
 - reviewing anything where there was no detection but the patch license
   was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
   SPDX license was correct

This produced a worksheet with 20 files needing minor correction.  This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg.  Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected.  This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.)  Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-02 11:10:55 +01:00
Thomas Gleixner
7249164346 genirq/irqdomain: Update irq_domain_ops.activate() signature
The irq_domain_ops.activate() callback has no return value and no way to
tell the function that the activation is early.

The upcoming changes to support a reservation scheme which allows to assign
interrupt vectors on x86 only when the interrupt is actually requested
requires:

  - A return value, so activation can fail at request_irq() time
  
  - Information that the activate invocation is early, i.e. before
    request_irq().

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Yu Chen <yu.c.chen@intel.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213152.848490816@linutronix.de
2017-09-25 20:38:24 +02:00
Linus Walleij
a9a1d2a782 pinctrl/gpio: Unify namespace for cross-calls
The pinctrl_request_gpio() and pinctrl_free_gpio() break the nice
namespacing in the other cross-calls like pinctrl_gpio_foo().
Just rename them and all references so we have one namespace
with all cross-calls under pinctrl_gpio_*().

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-09-22 11:02:10 +02:00
Philipp Zabel
d9e99bdfb7 pinctrl: stm32: explicitly request exclusive reset control
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.

No functional changes.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-08-14 15:01:01 +02:00
Masahiro Yamada
8db63f5361 pinctrl: stm32: select IRQ_DOMAIN_HIERARCHY instead of depends on
Drivers that need IRQ_DOMAIN_HIERARCHY should "select" it, but
drivers/pinctrl/stm32/Kconfig is the only exception that uses
"depends on" syntax.  This prevents GPIO drivers from select'ing
IRQ_DOMAIN_HIERARCHY.

For example, if I add "select IRQ_DOMAIN_HIERARCHY" to GPIO_XGENE_SB,
I get the following recursive dependency error.

drivers/gpio/Kconfig:13:error: recursive dependency detected!
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/gpio/Kconfig:13:	symbol GPIOLIB is selected by PINCTRL_STM32
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/pinctrl/stm32/Kconfig:3:	symbol PINCTRL_STM32 is selected by PINCTRL_STM32F429
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/pinctrl/stm32/Kconfig:11:	symbol PINCTRL_STM32F429 depends on IRQ_DOMAIN_HIERARCHY
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
kernel/irq/Kconfig:67:	symbol IRQ_DOMAIN_HIERARCHY is selected by GPIO_XGENE_SB
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/gpio/Kconfig:502:	symbol GPIO_XGENE_SB depends on GPIOLIB

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-08-01 10:04:41 +02:00
Linus Walleij
6183061967 Linux 4.12-rc7
-----BEGIN PGP SIGNATURE-----
 
 iQEcBAABAgAGBQJZUGOmAAoJEHm+PkMAQRiGhX8H/3fIhingPD01MBf98U0xGrJo
 yIXmhu6nFs7TM0lDVDcHsKgqLQIT69ll7PrSZrMkc1RGUIPINoCuJVuJqDre0kfB
 of5TX2KegqSx8h1vOWjGBCBjdYfPGyMdf9icf6KsGc/SlIdhN6WA99kglAjJA0Ve
 qPTNagF0ntUNg1lsXffxyfcHqFpyqw/Z/C4ie/byFsn9iJ1VG9mNlTWSud09vhuM
 3tvHzTUVAIWWuRrrgrvgqQpnwL+q5BfSDsXScMjBau0EK3RGGqG8EN6Kbkfa7VQ6
 aBoeboQjUijSJnVwvySdQ11MChTIOwZdfrNPra/1HD3WJNsSu4BIRt5JcAKcOhc=
 =qmSg
 -----END PGP SIGNATURE-----

Merge tag 'v4.12-rc7' into devel

Linux 4.12-rc7
2017-06-29 14:27:39 +02:00
Alexandre TORGUE
b7c747d462 pinctrl: stm32: Fix bad function call
In stm32_pconf_parse_conf function, stm32_pmx_gpio_set_direction is
called with wrong parameter value. Indeed, using NULL value for range
will raise an oops.

Fixes: aceb16dc2d ("pinctrl: Add STM32 MCUs support")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-06-09 10:51:54 +02:00
Alexandre TORGUE
b8bfcb09a4 pinctrl: stm32: remove useless check
There is no link between the number of elements of tab which contains all
pin desc (located in each pinctrl-stm32xxxx.c files) and the pin number
(defined in the tab).

Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-06-09 10:03:23 +02:00
Alexandre TORGUE
acaa037970 pinctrl: stm32: Implement .get_direction gpio_chip callback
Add .get_direction() gpiochip callback in STM32 pinctrl driver.

Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-05-31 02:05:49 +02:00
Alexandre TORGUE
9efa6d1a1e pinctrl: stm32: set pin to gpio input when used as interrupt
This patch ensures that pin is correctly set as gpio input when it is used
as an interrupt.

Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-05-31 02:04:41 +02:00
Alexandre TORGUE
ca028dbb18 pinctrl: stm32: Add STM32F469 MCU support
This patch which adds STM32F469 pinctrl and GPIO support, relies on the
generic STM32 pinctrl driver.

Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-04-24 14:26:14 +02:00
Alexandre TORGUE
4a4e5f6f77 pinctrl: stm32: replace device_initcall() with arch_initcall()
Pinctrl has to be registered earlier. Mainly to register bank irqdomain
earlier as other devices could use interrupts from those irqdomain.

Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-04-24 14:21:31 +02:00
Alexandre TORGUE
1dc9d28915 pinctrl: stm32: add possibility to use gpio-ranges to declare bank range
Use device tree entries to declare gpio range. It will allow to use
no contiguous gpio bank and holes inside a bank.

Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-04-24 14:20:05 +02:00
Alexandre TORGUE
deb30f51aa pinctrl: stm32: Add STM32H743 MCU support
This patch adds STM32H743 pinctrl and GPIO support, relies on the
generic STM32 pinctrl driver.

Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-02-06 09:38:30 +01:00
Alexandre TORGUE
dca72e09e0 pinctrl: stm32: fix bad location of gpiochip_lock_as_irq
Move gpio lock as irq from "domain alloc" callback to "domain activate"
callback. It will allow to use gpiolib sysfs correctly.

Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-01-30 16:26:28 +01:00
Gabriel Fernandez
c32c22eea0 pinctrl: stm32: activate strict mux mode
This activates strict mode muxing for the STM32 pin controllers,
as these do not allow GPIO and functions to use the same pin
simultaneously.

Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-12-30 09:06:39 +01:00
Linus Torvalds
20d5ba4928 Bulk pin control changes for the v4.10 kernel cycle:
No core changes this time. Mainly gradual improvement and
 feature growth in the drivers.
 
 New drivers:
 
 - New driver for TI DA850/OMAP-L138/AM18XX pinconf
 
 - The SX150x was moved over from the GPIO subsystem and
   reimagined as a pin control driver with GPIO support
   in a joint effort by three independent users of this
   hardware. The result was amazingly good!
 
 - New subdriver for the Oxnas OX820
 
 Improvements:
 
 - The sunxi driver now supports the generic pin control
   bindings rather than the sunxi-specific. Add debouncing
   support to the driver.
 
 - Simplifications in pinctrl-single adding a generic parser.
 
 - Two downstream fixes and move the Raspberry Pi BCM2835 over
   to use the generic GPIOLIB_IRQCHIP.
 -----BEGIN PGP SIGNATURE-----
 
 iQIcBAABAgAGBQJYTny8AAoJEEEQszewGV1zz0MP/2KLLiZtBaBo0hDfY2Oussjp
 JRO/VkjFIff/iDznkJJhMFPGwQ6ebp63vNRrwwOYwGa2GyZZrbeshul3oV89fyeL
 NYApweAFIOFnTI6TVb5k1cGoPJcck2OalSkwHNvPVEXYykf3xy6Jm0M81T9t8fsu
 xmSAfqvue9oYgDGN3jYVzsL9U6mGdWZV5fjFzwEfl/6oMA03/CMFdkDz6OBOj9ms
 addIx6fQEiS1XtIwEKnX6PS8Q78/vJ/Yl6IKow/5U5lTx5HR+nbECADdEM3jqper
 jifodSzJiN6fE3C55o9uupM8tVbu9lj18bb2UVOLiFB+IVlWYKekIzG+8Jg0YvJ7
 zEiLzXntNHGNM3Nvinf0AL42+Uz8Ar93AvhdZD2H4yqo6dA8ifojNnavuUa9piGR
 xlV8llwgSXZF8+b0ZodSFSS4R0zSGSXSimIlWDsdJ06UWHoJU2yijmkEJicXyS23
 Qlo+eK830F+e0FWHTEq+OsiFoCOrD3Zin3gfNtCKoLZpTf77YFOkF3aGMrrmoIRr
 MGahrssK+B6Hr8JzHWZDLpIEUL3VB+gHm6Vj4Tt5i2Ms7rw6hB60mu14PZ1pGlY0
 U9CFfYg9NSPqRrgkirlETI+l7rfvVHRxqgtMQSLE6uI1Nxw+6ubMRgB2uk92LQzv
 4F3H6v/5IBGqDRA5jr7a
 =Pkzu
 -----END PGP SIGNATURE-----

Merge tag 'pinctrl-v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl

Pull pinctrl updates from Linus Walleij:
 "Bulk pin control changes for the v4.10 kernel cycle:

  No core changes this time. Mainly gradual improvement and
  feature growth in the drivers.

  New drivers:

   - New driver for TI DA850/OMAP-L138/AM18XX pinconf

   - The SX150x was moved over from the GPIO subsystem and reimagined as
     a pin control driver with GPIO support in a joint effort by three
     independent users of this hardware. The result was amazingly good!

   - New subdriver for the Oxnas OX820

  Improvements:

   - The sunxi driver now supports the generic pin control bindings
     rather than the sunxi-specific. Add debouncing support to the
     driver.

   - Simplifications in pinctrl-single adding a generic parser.

   - Two downstream fixes and move the Raspberry Pi BCM2835 over to use
     the generic GPIOLIB_IRQCHIP"

* tag 'pinctrl-v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (92 commits)
  pinctrl: sx150x: use new nested IRQ infrastructure
  pinctrl: sx150x: handle missing 'advanced' reg in sx1504 and sx1505
  pinctrl: sx150x: rename 'reg_advance' to 'reg_advanced'
  pinctrl: sx150x: access the correct bits in the 4-bit regs of sx150[147]
  pinctrl: mt8173: set GPIO16 to usb iddig mode
  pinctrl: bcm2835: switch to GPIOLIB_IRQCHIP
  pinctrl: New driver for TI DA850/OMAP-L138/AM18XX pinconf
  devicetree: bindings: pinctrl: Add binding for ti,da850-pupd
  Documentation: pinctrl: palmas: Add ti,palmas-powerhold-override property definition
  pinctrl: intel: set default handler to be handle_bad_irq()
  pinctrl: sx150x: add support for sx1501, sx1504, sx1505 and sx1507
  pinctrl: sx150x: sort chips by part number
  pinctrl: sx150x: use correct registers for reg_sense (sx1502 and sx1508)
  pinctrl: imx: fix imx_pinctrl_desc initialization
  pinctrl: sx150x: support setting multiple pins at once
  pinctrl: sx150x: various spelling fixes and some white-space cleanup
  pinctrl: mediatek: use builtin_platform_driver
  pinctrl: stm32: use builtin_platform_driver
  pinctrl: sunxi: Testing the wrong variable
  pinctrl: nomadik: split up and comments MC0 pins
  ...
2016-12-13 07:59:10 -08:00
Geliang Tang
5b209efa3f pinctrl: stm32: use builtin_platform_driver
Use builtin_platform_driver() helper to simplify the code.

Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-11-22 09:57:39 +01:00
Alexandre TORGUE
1064a2b415 pinctrl: stm32: remove dependency with interrupt controller
This patch allows to probe stm32 pinctrl driver even if no interrupt
controller is defined to manage gpio irqs.

Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-10-31 21:25:15 +01:00
Arnd Bergmann
49cf2f29ac pinctrl: stm32: add IRQ_DOMAIN_HIERARCHY dependency
The newly added irqchip support for the stm32 pinctrl driver uses
hierarchical IRQ domains as provided by the NVIC primary irqchip.
This works great for any configuration that may be relevant on
stm32, but when doing compile-testing (randconfig), we can
enable it without NVIC or any other primary irqchip that
enables IRQ_DOMAIN_HIERARCHY:

drivers/pinctrl/stm32/pinctrl-stm32.c:212:13: error: 'irq_chip_eoi_parent' undeclared here (not in a function)
drivers/pinctrl/stm32/pinctrl-stm32.c:213:20: error: 'irq_chip_mask_parent' undeclared here (not in a function)
drivers/pinctrl/stm32/pinctrl-stm32.c:214:20: error: 'irq_chip_unmask_parent' undeclared here (not in a function)
drivers/pinctrl/stm32/pinctrl-stm32.c:215:20: error: 'irq_chip_set_type_parent' undeclared here (not in a function)

This adds a Kconfig dependency to limit compile-testing to
configurations that have IRQ_DOMAIN_HIERARCHY already enabled.
It's not obvious whether we should use 'depends on' or 'select'
here, I think either one works, with 'depends on' being more
intuitive, while 'select' would be less likely to cause dependency
loops.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 0eb9f68333 ("pinctrl: Add IRQ support to STM32 gpios")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-09-15 14:13:10 +02:00
Julia Lawall
d9048cdbc9 pinctrl: stm32: constify gpio_chip structures
These structures are only used to copy into other structures, so declare
them as const.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct gpio_chip i@p = { ... };

@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;

@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p

@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
 struct gpio_chip i = { ... };
// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-09-13 10:37:37 +02:00
Alexandre TORGUE
0eb9f68333 pinctrl: Add IRQ support to STM32 gpios
This patch adds IRQ support to STM32 gpios.

The EXTI controller has 16 lines dedicated to GPIOs.
EXTI line n can be connected to only line n of one of the GPIO ports, for
example EXTI0 can be connected to either PA0, or PB0, or PC0...
This port selection is done by specifying the port number into System
Config registers.

Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-09-13 10:13:01 +02:00
Alexandre TORGUE
25af8bfa96 pinctrl: Add STM32F746 MCU support
This patch which adds STM32F746 pinctrl and GPIO support, relies on the
generic STM32 pinctrl driver.

Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-07-11 14:35:44 +02:00
Patrice Chotard
4fac724fd7 pinctrl: stm32: factorize stm32_pconf_input/output_get()
As these 2 functions code are 95% similar, factorize them.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-05-31 10:06:12 +02:00
Linus Torvalds
a37571a29e Pin control bulk changes for the v4.7 kernel cycle:
Core changes:
 
 - Add the devm_pinctrl_register() API and switch all applicable drivers
   to use it, saving lots of lines of code all over the place.
 
 New drivers:
 
 - New driver for the Broadcom NS2 SoC.
 
 - New subdriver for the PXA25x SoCs.
 
 - New subdriver for the AMLogic Meson GXBB SoC.
 
 Driver improvements:
 
 - The Intel Baytrail driver now properly supports pin control.
 
 - The Nomadik, Rockchip, Broadcom BCM2835 supports the .get_direction() callback in
   the GPIO portions.
 
 - Continued development and stabilization of several SH-PFC
   SoC subdrivers: r8a7795, r8a7790, r8a7794 etc.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJXPZ9PAAoJEEEQszewGV1zboIQALtGX/tyKFzaOsj7WxHHjmfb
 yufqU62NE0sPT6/hzUY3a1U9dpakbMehBXy0go0vcShmPSznX2glFv4GR6LEeE0+
 o0JNv0d13f2s5WPEqn6L/ePuSuNNjfkwjZ7YJlAXx/WqAWI9c70H8/VHsXEObWOe
 ZsAZx2FdUFDOxugDWsCmU6kt7RXbqTzEz2M/dDANr4B2cRH/3yny797P2y9tLy3w
 Rqsdqw1C1A9SICSIRZ+YBWctXhRq5APsB75IncUYIQJF5hXoAcBCp6v+cNZHpXOw
 X9J+zKDeMjOSsVvOyHA+4P+vPYgkOPl9GuUVJRvnbfCZYKEhDM1e5F393Cf7gYYz
 dIEAzIFlPmZCMxog7AWEA0yDp2rJ2W/5WoN7pg+a5cKSHgriIry1sxDslBD2b9ZW
 XxdVm4pMOiVw6yokHI4g2hcDsZOEW8zhPQi1wPuVuJ3k1m7T/d13mFAFTSWwOLVx
 WFDLuD20ybkCVmxEs0ePrDzLcgEnxW40src6lqSzIx8bUBCH+iWPkIPH0fAJ6bNK
 TFtfcCFrtE2YmpxrCgZceTLER/7jAGkXFegbJq1epNmz7+0wbEbRxcVFE1IbYUBW
 ejslgTtLDvnzzkR7UISZF/Qna066tCGT52sEA82ZcrqytGkSTLB4kUDkQvXaCB0r
 4DLJ47K32mQu3MrOPLjE
 =tlvn
 -----END PGP SIGNATURE-----

Merge tag 'pinctrl-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl

Pull pin control updates from Linus Walleij:
 "This kernel cycle was quite calm when it comes to pin control and
  there is really just one major change, and that is the introduction of
  devm_pinctrl_register() managed resources.

  Apart from that linear development, details below.

  Core changes:

   - Add the devm_pinctrl_register() API and switch all applicable
     drivers to use it, saving lots of lines of code all over the place.

  New drivers:

   - driver for the Broadcom NS2 SoC

   - subdriver for the PXA25x SoCs

   - subdriver for the AMLogic Meson GXBB SoC

  Driver improvements:

   - the Intel Baytrail driver now properly supports pin control

   - Nomadik, Rockchip, Broadcom BCM2835 support the .get_direction()
     callback in the GPIO portions

   - continued development and stabilization of several SH-PFC SoC
     subdrivers: r8a7795, r8a7790, r8a7794 etc"

* tag 'pinctrl-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (85 commits)
  Revert "pinctrl: tegra: avoid parked_reg and parked_bank"
  pinctrl: meson: Fix eth_tx_en bit index
  pinctrl: tegra: avoid parked_reg and parked_bank
  pinctrl: tegra: Correctly check the supported configuration
  pinctrl: amlogic: Add support for Amlogic Meson GXBB SoC
  pinctrl: rockchip: fix pull setting error for rk3399
  pinctrl: stm32: Implement .pin_config_dbg_show()
  pinctrl: nomadik: hide nmk_gpio_get_mode when unused
  pinctrl: ns2: rename pinctrl_utils_dt_free_map
  pinctrl: at91: Merge clk_prepare and clk_enable into clk_prepare_enable
  pinctrl: at91: Make at91_gpio_template const
  pinctrl: baytrail: fix some error handling in debugfs
  pinctrl: ns2: add pinmux driver support for Broadcom NS2 SoC
  pinctrl: sirf/atlas7: trivial fix of spelling mistake on flagged
  pinctrl: sh-pfc: Kill unused variable in sh_pfc_remove()
  pinctrl: nomadik: implement .get_direction()
  pinctrl: nomadik: use BIT() with offsets consequently
  pinctrl: exynos5440: Use off-stack memory for pinctrl_gpio_range
  pinctrl: zynq: Use devm_pinctrl_register() for pinctrl registration
  pinctrl: u300: Use devm_pinctrl_register() for pinctrl registration
  ...
2016-05-19 12:50:56 -07:00
Patrice Chotard
3beed93c16 pinctrl: stm32: Implement .pin_config_dbg_show()
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-05-10 13:48:26 +02:00