The dra762x j5-eco is similar to dm814x with a bit different clocks
and devices.
[tony@atomide.com: updated to leave out adpll clock driver references]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enabling CPUFreq support for Tegra124 Chromebooks is causing the Tegra124
to hang when resuming from suspend.
When CPUFreq is enabled, the CPU clock is changed from the PLLX clock to
the DFLL clock during kernel boot. When resuming from suspend the CPU
clock is temporarily changed back to the PLLX clock before switching back
to the DFLL. If the DFLL is operating at a much lower frequency than the
PLLX when we enter suspend, and so the CPU voltage rail is at a voltage
too low for the CPUs to operate at the PLLX frequency, then the device
will hang.
Please note that the PLLX is used in the resume sequence to switch the CPU
clock from the very slow 32K clock to a faster clock during early resume
to speed up the resume sequence before the DFLL is resumed.
Ideally, we should fix this by setting the suspend frequency so that it
matches the PLLX frequency, however, that would be a bigger change. For
now simply disable CPUFreq support for Tegra124 Chromebooks to avoid the
hang when resuming from suspend.
Fixes: 9a0baee960 ("ARM: tegra: Enable CPUFreq support for Tegra124
Chromebooks")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
We can boot dra62x j5-eco using the dm814x code as the clocks and
devices are mapped in the device tree. The dra62x is also known
as jacinto 5 eco.
We may want to add separate soc_is macros for dra62x if needed,
but this gets us to the point where we can boot dra62x with just
dts changes.
Let's also print out the unknown hawkeye register to make things
a bit easier for new SoC variants.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This device tree was tested on a Sigma Designs SMP8758 Vantage-1172
Rev E1 development board.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Support Sigma Designs ARM-based (specifically, Cortex-A9 MPCore r3p0)
Tango4 "Secure Media Processor" platforms: smp8756, smp8758, smp8759
(8756 is single-core, the latter are dual-core).
Note: 8758 vs 8759: same chip, different package.
Support for older MIPS-based platforms can be found elsewhere:
https://github.com/mansr/linux-tangox
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Mostly some audio codec patches to enable it on more boards, and a bunch
devices activation (Ethernet, touchscreen, backlights). One more board has
been added too.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=1z4m
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.5-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Allwinner DT patches, round 2
Mostly some audio codec patches to enable it on more boards, and a bunch
devices activation (Ethernet, touchscreen, backlights). One more board has
been added too.
* tag 'sunxi-dt-for-4.5-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: dts: sun5i: Add dts file for the Empire Electronix D709 tablet
ARM: dts: sun7i: Enable gmac on Wits Pro A20 DKT
ARM: dt: sun7i: Enable audio codec on MK808C
ARM: sunxi: dt: enable audio codec on mk802
ARM: dts: sun7i: Add PA gpio pin to Wexler TAB7200 tablet
ARM: dts: sun7i: Add backlight node to Wexler TAB7200 tablet
ARM: dts: sun7i: Enable touchscreen on Wexler TAB7200 tablet
ARM: dts: sun7i: Enable PWM controller on Wexler TAB7200 tablet
ARM: dts: sun4i: gemei-g9: Enable PA GPIO pin configuration
ARM: dts: sun4i: Enable onboard codec used on the pov protab2-ips9 tablet
ARM: dts: sun5i: Enable onboard codec used on the UTOO P66 tablet
Signed-off-by: Olof Johansson <olof@lixom.net>
- addition of sound nodes for sama5d2 and the xplained
- addition of a new patform by Landis+Gyr: VInCo
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XTmq
-----END PGP SIGNATURE-----
Merge tag 'at91-4.5-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into next/dt
Second batch of DT changes for 4.5:
- addition of sound nodes for sama5d2 and the xplained
- addition of a new patform by Landis+Gyr: VInCo
* tag 'at91-4.5-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: at91/dt: sama5d2 Xplained: add pdmic node
ARM: at91/dt: sama5d2: add pdmic node
ARM: at91/dt: Add Support for the L+G VInCo platform
Signed-off-by: Olof Johansson <olof@lixom.net>
- Drop CONFIG_SOC_LS1021A support, as it needs LPAE which is not
available with imx_v6_v7_defconfig.
- Enable VF610_ADC, HDMI audio and PCI_MSI support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWeV+iAAoJEFBXWFqHsHzOB1sH/Ru5qv6aLNiEXXeCS+NGQyQR
WMiJhxEYEzrXQ7nut04MCxXlmU+6bawxeK/fFv2Ll81RNQHKuzSXQxbuQCtrgDB1
Vwf1KcLfMiyHS2gOlmv6CXAGU39Hvtkc7GEiwypHOEkjFLQuif/0biLGwDAJ3UY0
VHD0ZokirveOcP3/kwR6AfIoY13GYiVRMTiSSLtzFE3OwYDpkjoxv9pQCNHL6bl+
7Zp8T72kEo4SIfeA9lrl3ywuBtR2sp1sASbLWPkgRupWK4uXkd2PAYVk2tehfGn8
6bcnfCVoBGg4zqHiFgQMoszobVXoybPZ0dmottae7+C9jf40TQKxvn/FM/8h8B0=
=Fxdw
-----END PGP SIGNATURE-----
Merge tag 'imx-defconfig-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/defconfig
The i.MX defconfig updates for 4.5:
- Drop CONFIG_SOC_LS1021A support, as it needs LPAE which is not
available with imx_v6_v7_defconfig.
- Enable VF610_ADC, HDMI audio and PCI_MSI support
* tag 'imx-defconfig-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx_v6_v7_defconfig: enable PCI_MSI
ARM: imx_v6_v7_defconfig: Select HDMI audio support
ARM: imx_v6_v7_defconfig: Select VF610_ADC
ARM: imx_v6_v7_defconfig: Remove CONFIG_SOC_LS1021A
Signed-off-by: Olof Johansson <olof@lixom.net>
- New boards support: imx51-ts4800, imx6q-novena, CompuLab imx7d SoM/SBC,
vf610m4-cosmic
- Add ADC device support for imx6ul and imx7d
- Remove config space from PCIe controller ranges property for i.MX6
- Add Vivante GPU nodes for i.MX6
- Add DCU, LCD, and SATA devices for LS1021A
- A series to update Ventana gw5xxx boards getting HDMI and LVDS to work
simultaneously and devices like PWM and SPI added
- Quite a few random cleanups and minor updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWeV5EAAoJEFBXWFqHsHzOk8YH/RrzIcDxVa7E6PiVErJmDluH
ihMgY1mQcgXBcBEVKc0F9gKXZVN7W1xHGTHxVZp83mTxEJArBjFhojFQYReUaALU
sQKot0sD8EWBlcC+fvuLzhHc8jE2Udioi/Ys/kgl8T82Q/LXTCnUmBnsPaVshqod
WQ4i4Hk/QV6FbCEgvJvwEMEth53JYLVlAkuVbXi32eo7iv6u6d/LEdCW88bpV8Gv
OxnGg8BiBV3TdAaAcNX72p5IRy9AYMY2hYIx9MCec+H2ws/jzn7xvfkhLta6luTP
4JMvdToQWkhscIEDK1Q/3PtJVmX1al1PWKLTve3tza6jTTc7Opav8XN1hH3nJls=
=hXxT
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
The i.MX device tree updates for 4.5:
- New boards support: imx51-ts4800, imx6q-novena, CompuLab imx7d SoM/SBC,
vf610m4-cosmic
- Add ADC device support for imx6ul and imx7d
- Remove config space from PCIe controller ranges property for i.MX6
- Add Vivante GPU nodes for i.MX6
- Add DCU, LCD, and SATA devices for LS1021A
- A series to update Ventana gw5xxx boards getting HDMI and LVDS to work
simultaneously and devices like PWM and SPI added
- Quite a few random cleanups and minor updates
* tag 'imx-dt-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (50 commits)
ARM: dts: imx7d: sbc-imx7: add basic board support
ARM: dts: imx7d: cl-som-imx7: add basic module support
ARM: dts: TS-4800: add touchscreen support
ARM: dts: ts-4800: Add LCD support
ARM: dts: imx6q: add Novena board
devicetree: bindings: Add vendor prefix for Kosagi
ARM: dts: TS-4800: use weim IP to map the FPGA
ARM: dts: TS-4800: drop uart rts/cts pin reservations
ARM: dts: imx6: add Vivante GPU nodes
ARM: dts: imx28: add alternate auart4 pinmux
ARM: dts: ls1021a: add sata node to dts
ARM: dts: TS-4800: add basic device tree
of: documentation: add bindings documentation for TS-4800
of: add vendor prefix for Technologic Systems
ARM: dts: imx7d-sdb: add ADC support
ARM: dts: imx7d.dtsi: add ADC support
ARM: dts: vf-colibri: add CAN support
ARM: mxs: dt: cfa10057: fix backlight PWM
ARM: dts: imx6qdl: move GIC to right location in DT
ARM: dts: imx6qdl: add IPU aliases
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- Select HAVE_IMX_SRC for i.MX7 to avoid a randconfig build error
- Enable cpufreq support on i.MX7D
- A couple of random cleanup on iomux-imx31 and mach-imx6ul
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWeVfeAAoJEFBXWFqHsHzOOmcH/A3mzA0g2FLMZIbJNY5tqrap
z1aejsrdkL00vJWGcI0FJt7G1JkYUFYPjjDnbkbeYnXwfi66ZafWdHeSy5QIFfFv
lbbF5Na9FESO5A+iWtvpScS/Frz1kk8Uq4SDiglzq+pV9MmQH7Ik3bbk57/h2sGA
Uk+SntoiEPmU0d/Jp0pnA66g6FYdDXhl6Ie1fBZSsToCDVvG/dD2O37NrhehzH1A
htxcPjuEfmYJRju3T2zgpTdgQ/vchMoCDH2hndi52LVz2LF6RRvoNvhm/qPM4Pg9
OlifVrFa8LMBSV9az7Fu9w0GYyKkHdE5ECxXWJvCi0w+p1zGb3rWf3Aj6aR4kag=
=Gsgx
-----END PGP SIGNATURE-----
Merge tag 'imx-soc-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/soc
The i.MX SoC updates for 4.5:
- Select HAVE_IMX_SRC for i.MX7 to avoid a randconfig build error
- Enable cpufreq support on i.MX7D
- A couple of random cleanup on iomux-imx31 and mach-imx6ul
* tag 'imx-soc-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx: select SRC for i.MX7
ARM: mach-imx: iomux-imx31: fix spelling mistake in error message
ARM: imx: enable cpufreq device on i.mx7d
mach-imx/mach-imx6ul.c: proper constness with __initconst
Signed-off-by: Olof Johansson <olof@lixom.net>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Cc: arm@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Cc: arm@kernel.org
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The rk808 supplies two clock outputs with one going back into the soc as
32kHz supply, supplying some core soc clocks with it. The system can boot
without it being present, but it is needed for example as source clock
for the thermal driver.
Signed-off-by: Heiko Stuebner <heiko.stuebner@collabora.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This enables the newly added hardware crypto module
found for example on the rk3288.
Signed-off-by: Heiko Stuebner <heiko.stuebner@collabora.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The io-domain driver is necessary to notify the soc about voltages changes
happening on supplying regulators. Probably the most important user right
now is the mmc tuning code, where the soc needs to get notified when the
voltage is dropped to the 1.8V point.
As this option is necessary to sucessfully tune UHS cards etc, it should
get built in.
Signed-off-by: Heiko Stuebner <heiko.stuebner@collabora.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
updates the EDMA bindings based on the various fixes to split EDMA into
separate independent devices. It also adds support for more devices on the
CompuLab cm-t335 and LogicPD Torpedo boards, and enables the new bindings
for qspi for am437x and dra7. There are also few dra7 regulator fixes, and
change of gpoi-key,wakeup to wakeup-source.
These depend on commit ae0add740c ("dmaengine: edma: DT: Change reserved
slot array from 16bit to 32bit type") already merged into mainline.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=+G24
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.5/dt-pt2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Second set of omap device tree changes for v4.5 merge window. This series
updates the EDMA bindings based on the various fixes to split EDMA into
separate independent devices. It also adds support for more devices on the
CompuLab cm-t335 and LogicPD Torpedo boards, and enables the new bindings
for qspi for am437x and dra7. There are also few dra7 regulator fixes, and
change of gpoi-key,wakeup to wakeup-source.
These depend on commit ae0add740c ("dmaengine: edma: DT: Change reserved
slot array from 16bit to 32bit type") already merged into mainline.
* tag 'omap-for-v4.5/dt-pt2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: LogicPD Torpedo: Add Touchscreen Support
ARM: dts: DRA7-EVM: Add regulator-allow-bypass property for ldo9
ARM: dts: DRA72-EVM: Add regulator-allow-bypass property for ldo1 and ldo2
ARM: dts: AM4372: add entry for qspi mmap region
ARM: dts: DRA7: add entry for qspi mmap region
ARM: OMAP2+: LogicPD Torpedo: Revert Duplicative Entries
ARM: OMAP2+: LogicPD Torpedo + Wireless: Add Bluetooth
ARM: OMAP2+: LogicPD Torpedo: Add LCD Type 15 Support
ARM: dts: cm-t335: add support for bluetooth
ARM: dts: cm-t335: add support for DVI/LCD
ARM: dts: cm-t335: add support for I2C GPIO expander
ARM: dts: cm-t335: add support for SBC-T335
ARM: dts: cm-t335: add support for USB0
ARM: dts: omap: replace legacy *,wakeup property with wakeup-source
ARM: dts: am335x: replace gpio-key,wakeup with wakeup-source property
ARM: DTS: am437x: Use the new DT bindings for the eDMA3
ARM: DTS: am33xx: Use the new DT bindings for the eDMA3
dmaengine: edma: DT: Change reserved slot array from 16bit to 32bit type
dmaengine: edma: DT: Change memcpy channel array from 16bit to 32bit type
Signed-off-by: Olof Johansson <olof@lixom.net>
change the omap initcall levels a bit to initialize things later to allow
early device drivers at core_initcall level. This makes things easier
for us as most clocks can be made into regular device drivers except for
a few early clocks needed to initialize system timers. I wanted to have
these changes sit in Linux next for a few weeks before sending out a pull
request, and so far now issues have showed up.
The other changes in this series are timer changes for making use of the
new PWM driver, and timer changes to support more high security SoCs.
Also few minor improvments for module autoidle settings for ti81xx spinbox
and dra7 debug on uart4 in hwmod code. The rest is pretty much just removal
of platform data for SoCs that are all device tree only nowadays.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=69mE
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.5/soc-initcall' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
SoC changes for omaps for v4.5 merge window. The main change here is to
change the omap initcall levels a bit to initialize things later to allow
early device drivers at core_initcall level. This makes things easier
for us as most clocks can be made into regular device drivers except for
a few early clocks needed to initialize system timers. I wanted to have
these changes sit in Linux next for a few weeks before sending out a pull
request, and so far now issues have showed up.
The other changes in this series are timer changes for making use of the
new PWM driver, and timer changes to support more high security SoCs.
Also few minor improvments for module autoidle settings for ti81xx spinbox
and dra7 debug on uart4 in hwmod code. The rest is pretty much just removal
of platform data for SoCs that are all device tree only nowadays.
* tag 'omap-for-v4.5/soc-initcall' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Remove device creation for omap-pcm-audio
ARM: OMAP1: Remove device creation for omap-pcm-audio
ARM: OMAP2+: Change core_initcall levels to postcore_initcall
ARM: DRA7: hwmod: Enable DEBUG_LL for UART4
ARM: OMAP: RX-51: fix a typo in log writing
ARM: omap4: hwmod: Remove elm address space from hwmod data
ARM: OMAP2+: timer: Remove secure timer for DRA7xx HS devices
ARM: OMAP: dmtimer: check for fixed timers during config
ARM: OMAP2+: Remove omap_mmu_dev_attr structure
ARM: OMAP4: hwmod data: Remove legacy IOMMU attr and addrs
ARM: OMAP3: hwmod data: Remove legacy IOMMU data
ARM: OMAP2+: Remove legacy device instantiation of IOMMUs
ARM: OMAP2+: Add hwmod spinbox support for dm816x
ARM: OMAP: add DT support for ti,dm816-timer
ARM: OMAP: dmtimer: Add clock source from DT
Signed-off-by: Olof Johansson <olof@lixom.net>
CPU_IDLE and ARM TWD timer. This is probably a common configuration setup
for people making products with these SoCs so let's make sure it works.
Also a wakeirq fix for duovero parlor making my life a bit easier as that
allows me to run basic PM regression tests on it.
It would be nice to have these in v4.4, but if it gets too late for that
because of the holidays, it is not super critical if these get merged for
v4.5.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tGjX
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.4/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Few fixes for omaps to allow am437x only builds to boot properly with
CPU_IDLE and ARM TWD timer. This is probably a common configuration setup
for people making products with these SoCs so let's make sure it works.
Also a wakeirq fix for duovero parlor making my life a bit easier as that
allows me to run basic PM regression tests on it.
It would be nice to have these in v4.4, but if it gets too late for that
because of the holidays, it is not super critical if these get merged for
v4.5.
* tag 'omap-for-v4.4/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix UART wakeirq for omap4 duovero parlor
ARM: OMAP2+: AM43xx: select ARM TWD timer
ARM: OMAP2+: am43xx: enable GENERIC_CLOCKEVENTS_BROADCAST
Signed-off-by: Olof Johansson <olof@lixom.net>
- clean up mcvevk dts file, replace space with tab
- Disable SDMMC node in base socfpga.dtsi file
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VS3e
-----END PGP SIGNATURE-----
Merge tag 'socfpga_dts_for_v4.5_part_2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/dt
SoCFPGA DTS update for v4.5, part 2
- clean up mcvevk dts file, replace space with tab
- Disable SDMMC node in base socfpga.dtsi file
* tag 'socfpga_dts_for_v4.5_part_2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: socfpga: dts: Enable MMC support at correct place in the DT
ARM: socfpga: Repair incorrectly applied MCV patch
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge in cleanup to avoid internal conflicts with newly added code.
* treewide/cleanup:
ARM: use "depends on" for SoC configs instead of "if" after prompt
ARM/clocksource: use automatic DT probing for ux500 PRCMU
ARM: use const and __initconst for smp_operations
ARM: hisi: do not export smp_operations structures
Signed-off-by: Olof Johansson <olof@lixom.net>
support for the efuses on Rockchip socs and some improvements for
rk3288 regulators.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJWd0xyAAoJEPOmecmc0R2B71UIAJu6jDdfk5kmYzyXjBloBNwd
PVRojGzVjCwCiVKX7GWINSf3D7dTKeYUwVs9uouVW4Q/iIk/l4Iq46+yg20ZODNM
3haS2hwztRPEKeU+0qhYdoJf2cWOKzk0RP90umTMMVt2xnqbQCBFAW4NuE4DBLHe
5o7R99ORKHi+IjBaI6Wtk1JoRNNkyYIDW6eLC9mxAJs32mr1ee45uidhPBD+VX+n
1nf/yUPs6bc1yPyNhFN49AywYvjg02y96/4ER6bBtOcEw91uDc0ld0M10H/mvujT
B+w8U6xBUWulUU53MS8aVKDZ+bp4o6YZZbIq/FJtaz3c+bhj8Rjl4UnlZh+gaiA=
=Zp6y
-----END PGP SIGNATURE-----
Merge tag 'v4.5-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Another new soc - the rk3228 quad-core cortex-a7, a new rk3036 board,
support for the efuses on Rockchip socs and some improvements for
rk3288 regulators.
* tag 'v4.5-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add the kylin board for rk3036
ARM: dts: rockchip: add the sdio/sdmmc node for rk3036
ARM: dts: rockchip: fix the pinctrl bias settings for rk3036
ARM: dts: rockchip: add eFuse node for rk3188 SoCs
ARM: dts: rockchip: add eFuse node for rk3066a SoCs
ARM: dts: rockchip: add eFuse config of rk3288 SoC
ARM: dts: rockchip: add rk3228-evb board
ARM: dts: rockchip: add core rk3228 dtsi
clk: rockchip: Add the clock ids of rk3288 eFuses
ARM: dts: rockchip: Fix typo in rk3288 sdmmc card detect pin name
ARM: dts: rockchip: fix voltage ranges for rk3288-evb-act8846 board
ARM: dts: rockchip: move the public part to rk3288-evb common
ARM: dts: rockchip: add 2 regulators for rk3288-evb-act8846
ARM: dts: rockchip: correct the name of REG8 for rk3288-evb-act8846
clk: rockchip: add dt-binding header for rk3228
clk: rockchip: add id for mipidsi sclk on rk3288
Signed-off-by: Olof Johansson <olof@lixom.net>
quad-core Cortex-A7 cpu.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJWcdThAAoJEPOmecmc0R2BFeMH/2jlwJrDe88hK1/7uQaFhKTN
Ykiphn6JM33/32D8iGNeoU1/ylW8y72Yb09mPwaBbpwCqtNlhb7iJIIhVqAOac57
PfJgTvq6bzXeqsKQkstZ3fCu/TP4rucXH6D1XUmR3N5BIfo7iNjrxR2QnKXv522E
HABnLjS7AY/CZXp2yudwku9RBBG1w0yGqxbvyfJEnOsuzopb50yBEAls6UXY1yei
W/bY2fEeiQLtt2SWjS40p9+PZcrG2VQHDuKefhD8HeRIROXg/36QfM/DXxGJnJOA
3mMYx+zGxfWul+b82SsS6Z4tKQ+GCG7G5ABc2Gnd2NYpa3ESIJJQRLGU3VozidA=
=NGaT
-----END PGP SIGNATURE-----
Merge tag 'v4.5-rockchip-soc-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/soc
SMP special case for the rk3036 and addition of the rk3228
quad-core Cortex-A7 cpu.
* tag 'v4.5-rockchip-soc-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: rockchip: enable support for RK3228 SoCs
ARM: rockchip: use const and __initconst for rk3036 smp_operations
ARM: rockchip: add support smp for rk3036
Signed-off-by: Olof Johansson <olof@lixom.net>
Add LPC18xx EEPROM driver and MMA7455 IIO driver for the
accelerometer found on EA4357 Dev kit.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJWdyJeAAoJEF5zSH4+/j/aiCgH/iE5+0oo4g0c6doBjeAxNd7l
6R9gr9Jd6NUFMOoBLoCi3ANyi32B5TLngNxsH/lC8xnMdwW0Fdxo2hmULqEC7XUb
NaXVlgZmiD6ZorYo9q5aScUBQlH6T9HEgpOSaKxq3zfpcTkcOWstWCSELTZgR3vt
pU2V8AOSXJZcY/o5UZgsyomSmzajU1W52LhxyKjT5lnlfqrA+n3qqbKuw6k77mR+
CD+OCmqmAwFwQot4Sy020cHQslHio/uukkPXuM6kmGoiw1iLbwrHjhtiGES+2Dfe
bqZVNIpNwbQXdE9gb3p/as7hYNS1m1ha1AR2piLAPlov7YaZq9aPv/sOxrDOwl8=
=J6Rm
-----END PGP SIGNATURE-----
Merge tag 'lpc18xx_defconfig_for_4.5' of https://github.com/manabian/linux-lpc into next/defconfig
Defconfig additions for LPC18xx platform
Add LPC18xx EEPROM driver and MMA7455 IIO driver for the
accelerometer found on EA4357 Dev kit.
* tag 'lpc18xx_defconfig_for_4.5' of https://github.com/manabian/linux-lpc:
ARM: configs: lpc18xx: enable EEPROM NVMEM driver
ARM: configs: lpc18xx: enable mma7455 IIO driver
Signed-off-by: Olof Johansson <olof@lixom.net>
Move the include of the reset contoller to include/dt-bindings/reset.
Add basic support for mt2701 SoC and evaluation board.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=qUem
-----END PGP SIGNATURE-----
Merge tag 'v4.4-next-dts' of https://github.com/mbgg/linux-mediatek into next/dt
Add regulators to the scpsys binding.
Move the include of the reset contoller to include/dt-bindings/reset.
Add basic support for mt2701 SoC and evaluation board.
* tag 'v4.4-next-dts' of https://github.com/mbgg/linux-mediatek:
dt-bindings: soc: Add supplies for Mediatek SCPSYS unit
ARM: mediatek: DT: Move reset controller constants into common location
ARM: dts: mediatek: add MT2701 basic support
Document: DT: Add bindings for mediatek MT2701 SoC Platform
Signed-off-by: Olof Johansson <olof@lixom.net>
Add dts for the following boards:
- Zyxel NSA325
- PogoPlug series 4
Add GPU support for Dove
Update boolean property to wakeup source for isil
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlZ0DyIACgkQCwYYjhRyO9UXAgCcCB9oM0SblUt6+OqKVXEdwwNU
2u4AoJPIDr/m9QoIvBj+H55XeGCmXFuI
=KHo9
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.5-3' of git://git.infradead.org/linux-mvebu into next/dt
mvebu dt for 4.5 (part 3)
Add dts for the following boards:
- Zyxel NSA325
- PogoPlug series 4
Add GPU support for Dove
Update boolean property to wakeup source for isil
* tag 'mvebu-dt-4.5-3' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada: replace isil, irq2-can-wakeup-machine with wakeup-source property
ARM: dts: enable GPU for SolidRun's Cubox
ARM: dts: dove: add DT GPU support
ARM: mvebu: kirkwood: add PogoPlug series 4 device tree
ARM: mvebu: add kirkwood compatibles for cloudengine boards
ARM: dts: kirkwood: Add DTS for Zyxel NSA325
Signed-off-by: Olof Johansson <olof@lixom.net>
On several Renesas ARM SoCs, the GIC is described in DT as being a
Cortex A9 GIC, while it's actually a PL390. This is not only stated in
the documentation, but has been verified by reading the GICD_IIDR
register.
To correct this:
1. Update the DT compatible value to match reality,
2. Update the board staging drivers to match the above.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=+GQm
-----END PGP SIGNATURE-----
Merge tag 'renesas-gic-cleanup-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/cleanup
Renesas ARM Based SoC GIC Cleanup for v4.5
On several Renesas ARM SoCs, the GIC is described in DT as being a
Cortex A9 GIC, while it's actually a PL390. This is not only stated in
the documentation, but has been verified by reading the GICD_IIDR
register.
To correct this:
1. Update the DT compatible value to match reality,
2. Update the board staging drivers to match the above.
* tag 'renesas-gic-cleanup-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
staging: board: armadillo800eva: Use "arm,pl390"
staging: board: kzm9d: Use "arm,pl390"
ARM: shmobile: r8a7778 dtsi: Use "arm,pl390" for GIC
ARM: shmobile: emev2 dtsi: Use "arm,pl390" for GIC
ARM: shmobile: r8a7740 dtsi: Use "arm,pl390" for GIC
ARM: shmobile: r7s72100 dtsi: Use "arm,pl390" for GIC
Signed-off-by: Olof Johansson <olof@lixom.net>
* Use SoC-specific usb-dmac and IPMMU compatibility strings
* Add internal delay for i2c IPs
* Add missing serial devices to r8a7793
* Enable DMA for r8a7793 serial devices
* Add serial port config to chosen/stdout-path
* Tidyup #sound-dai-cells settings for r8a7798/bockw
* Remove deprecated #gpio-range-cells from r8a7793
* Add EtherAVB support to r8a7791
* Add MSIOF support to sh73a0
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=bncx
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt3-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Third Round of Renesas ARM Based SoC DT Updates for v4.5
* Use SoC-specific usb-dmac and IPMMU compatibility strings
* Add internal delay for i2c IPs
* Add missing serial devices to r8a7793
* Enable DMA for r8a7793 serial devices
* Add serial port config to chosen/stdout-path
* Tidyup #sound-dai-cells settings for r8a7798/bockw
* Remove deprecated #gpio-range-cells from r8a7793
* Add EtherAVB support to r8a7791
* Add MSIOF support to sh73a0
* tag 'renesas-dt3-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (25 commits)
ARM: shmobile: r8a779x: use SoC-specific usb-dmac compatibility strings
ARM: shmobile: r8a7794: IPMMU compat string SoC part number update
ARM: shmobile: r8a7793: IPMMU compat string SoC part number update
ARM: shmobile: r8a7791: IPMMU compat string SoC part number update
ARM: shmobile: r8a7790: IPMMU compat string SoC part number update
ARM: shmobile: r8a7794: dtsi: add internal delay for i2c IPs
ARM: shmobile: r8a7791: dtsi: add internal delay for i2c IPs
ARM: shmobile: r8a7790: dtsi: add internal delay for i2c IPs
ARM: shmobile: r8a7793: Describe DMA for the serial ports
ARM: shmobile: r8a7793: Add missing serial devices to DT
ARM: shmobile: lager dts: Add serial port config to chosen/stdout-path
ARM: shmobile: porter dts: Add serial port config to chosen/stdout-path
ARM: shmobile: silk dts: Add serial port config to chosen/stdout-path
ARM: shmobile: gose dts: Add serial port config to chosen/stdout-path
ARM: shmobile: bockw dts: Update console parameters
ARM: shmobile: ape6evm dts: Add serial port config to chosen/stdout-path
ARM: shmobile: alt dts: Add serial port config to chosen/stdout-path
ARM: shmobile: koelsch dts: Add serial port config to chosen/stdout-path
ARM: shmobile: r8a7778: tidyup #sound-dai-cells settings
ARM: shmobile: bockw dts: Override #sound-dai-cells to zero
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- Fix Ethernet PHY mode on i.MX6 Ventana boards, which can result in
a non-functional Ethernet when Marvell phy driver rather than generic
phy driver is selected.
- Fix an assigned-clock configuration bug on imx6qdl-sabreauto board
which was introduced by commit ed339363de ("ARM: dts:
imx6qdl-sabreauto: Allow HDMI and LVDS to work simultaneously").
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWcnPzAAoJEFBXWFqHsHzOvfAIALZo+lVpA3c89ZuDJn0bKfsI
hsV2wfMW1N5BhLN0AGjNIk/nk/YWhZ57gZyQ8miMdz2VeQRSgcjRaFFfEGRGOGop
OrrKpgmRKmUNxMrvztLlMmb1hGxpHOO7z/CXO3UrzDRIiw9lzxYymt0Re2UHiE1u
+tekMe7xBdimfMVmcM8RX/FOZC81tUjH3W8fyPbbzTTgrAnLPmXcfjtHkXy2VPw0
5ikWCJhFWB9ODnmKHbdA7YsNh52JAe5BieWiLXzLj33XJNDBbiFBbBltbo+BJZnp
ZaIek/fGHbq7ouCSLdRq7SEQn6ZbjpHhlic/okqNX0ux29QpY2GKTbiq8fLmcLU=
=wMKP
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
The i.MX fixes for 4.4, 3rd round:
- Fix Ethernet PHY mode on i.MX6 Ventana boards, which can result in
a non-functional Ethernet when Marvell phy driver rather than generic
phy driver is selected.
- Fix an assigned-clock configuration bug on imx6qdl-sabreauto board
which was introduced by commit ed339363de ("ARM: dts:
imx6qdl-sabreauto: Allow HDMI and LVDS to work simultaneously").
* tag 'imx-fixes-4.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6: Fix Ethernet PHY mode on Ventana boards
ARM: dts: imx: Fix the assigned-clock mismatch issue on imx6q/dl
* multi_v7_defconfig and shmobile_defconfig:
- Enable frame buffer console for armadillo800eva
- Enable missing Renesas ARM support based on DTSes
- Drop useless CONFIG_USB_RCAR_PHY=y
* shmobile_defconfig only:
- Enable CONFIG_PRINTK_TIME
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=3O01
-----END PGP SIGNATURE-----
Merge tag 'renesas-defconfig-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/defconfig
Renesas ARM Based SoC Defconfig Updates for v4.5
* multi_v7_defconfig and shmobile_defconfig:
- Enable frame buffer console for armadillo800eva
- Enable missing Renesas ARM support based on DTSes
- Drop useless CONFIG_USB_RCAR_PHY=y
* shmobile_defconfig only:
- Enable CONFIG_PRINTK_TIME
* tag 'renesas-defconfig-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: multi_v7_defconfig: Enable frame buffer console for armadillo800eva
ARM: multi_v7_defconfig: Enable missing Renesas ARM support based on DTSes
ARM: multi_v7_defconfig: Drop useless CONFIG_USB_RCAR_PHY=y
ARM: shmobile: defconfig: Enable frame buffer console for armadillo800eva
ARM: shmobile: defconfig: Enable missing support based on DTSes
ARM: shmobile: defconfig: Drop useless CONFIG_USB_RCAR_PHY=y
ARM: shmobile: defconfig: Enable CONFIG_PRINTK_TIME
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/configs/multi_v7_defconfig
- a single patch to add watchdog drivers to sama5_defconfig
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJWcTppAAoJEAf03oE53VmQ5gcH/252ZvQZghdwzRBOGrmabRGt
9llUe/bGnd6ah582VjYtEHk27815+7qyFWQfLs501n/5/RYAIRIzdin/QrjdUbh1
hHr881ym5MgPYAwFEZ9yK1GVGyM3QUybVXFDPromBw9fvfVCcqOn/U/4gRCdNlQw
90j167bhkCWO4uhdZ6yoS6Apv/cs4BF/g6sVXmXuJkck98w8e+wHXZ3LzUC9jP97
RkmZU3YVbRH0/WYzjx8ymjyyqyJUDtU+jAkeDT6Gnjs1tfrM0irXXkRv3zrB6LJG
dPmXK9w6rjF+X/hqo4ojKzuZrxyA1qD9CHVOBalgXYXETlhrl+YBRNWOC/yk7g4=
=s+Hb
-----END PGP SIGNATURE-----
Merge tag 'at91-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/defconfig
First defconfig pull-request for 4.5:
- a single patch to add watchdog drivers to sama5_defconfig
* tag 'at91-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/defconfig: enable watchdog drivers in sama5_defconfig
Signed-off-by: Olof Johansson <olof@lixom.net>
- addition of nodes for sama5d2 & sama5d4
- some fixes for i2c hold time, compatible stings
- addition of a new patform by DENX: the MA5D4 SoM and EVK
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJWcThWAAoJEAf03oE53VmQuRgIAJG4qqeh62GE5naX6wCiaPmi
bWay4W1iMImiX+DHIKgFpBdHmjbHUlajUqifk4+CQ08FuFBiSl23pOP9U0j4b0Hr
jglidWJRpm2vlqN+25R/lJgwA3jleFtDn/l5EW8P5kL8WkXfXOWU7Jop+Pqxae0a
aAmKZKi9MU6mwUyZnDEYpNf29pILbBve+vPqRRVaFXiOzDYXzl3LnTE2zQvSeY0U
dpkrrH2jbjfJ8gWmAvfMqTuJLwbgv00H5MvcaP3Q8MR+7F6ATZUtqjSiMF+aRYCM
sUYCJTG4WglZvWBFTn4LcSTXZgwfVjM4r59hd18Ep2TGnXk3fRS17xTxtoAQczE=
=+zlN
-----END PGP SIGNATURE-----
Merge tag 'at91-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/dt
First batch of DT changes for 4.5:
- addition of nodes for sama5d2 & sama5d4
- some fixes for i2c hold time, compatible stings
- addition of a new patform by DENX: the MA5D4 SoM and EVK
* tag 'at91-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/dt: sama5d2 Xplained: pmic needs a specific sda hold time
ARM: at91/dt: sama5d4: update i2c compatible string
ARM: at91/dt: sama5d4 master clock can run at 200MHz now
ARM: at91/dt: sama5d2: add watchdog node
ARM: at91/dt: sama5d4: Add support for DENX MA5D4 SoM and EVK
ARM: at91/dt: sama5d4: Add pinmux for 8-bit MMC0 bus
ARM: at91/dt: sama5d4: Fix mmc0 pinmux comments
Signed-off-by: Olof Johansson <olof@lixom.net>
improper usage of WARN() and a fix
for unmet 'select' dependencies.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=u3KY
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v4.5/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/fixes-non-critical
This pull request includes a fix for improper usage of WARN() and a fix
for unmet 'select' dependencies.
* tag 'davinci-for-v4.5/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: fix a problematic usage of WARN()
ARM: davinci: only select WT cache if cache is enabled
Signed-off-by: Olof Johansson <olof@lixom.net>
ABB and PBIAS are internal LDO control regulators that are needed for
maintaining proper functionality of OMAP architecture SoCs. Enable the
same. PBIAS is already enabled, so just enable ABB regulator as well.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Enable PMIC for AM437x platforms such as AM437x-sk similar to commit
a186cf10da ("ARM: omap2plus_defconfig: enable TPS65218 configs").
This allows multi_v7_defconfig to boot up on AM437x-sk platform.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Allwinner device-tree related patches for the 4.5 merge window.
* Support for the H3
* Addition of the RSB to the relevant devices (sun8i, sun9i)
* Addition of the Video Engine clocks for the older SoCs (sun4i, sun7i)
* Addition of the DRAM gates for the older SoCs (sun4i, sun7i)
* Addition of the audio codec to a bunch of boards
* New board: ICNova SWAC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qu2G
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.5' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Allwinner DT changes for 4.5
Allwinner device-tree related patches for the 4.5 merge window.
* Support for the H3
* Addition of the RSB to the relevant devices (sun8i, sun9i)
* Addition of the Video Engine clocks for the older SoCs (sun4i, sun7i)
* Addition of the DRAM gates for the older SoCs (sun4i, sun7i)
* Addition of the audio codec to a bunch of boards
* New board: ICNova SWAC
* tag 'sunxi-dt-for-4.5' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (40 commits)
ARM: dts: sun7i: Olimex A20-SOM-EVB: Enable mmc3 (baseboard SD socket)
ARM: dts: sun7i: Olimex A20-SOM-EVB: Add LRADC keys
ARM: dts: sun9i: cubieboard4: Enable Reduced Serial Bus controller
ARM: dts: sun9i: cubieboard4: Enable consumer IR receiver
ARM: dts: sun9i: cubieboard4: Enable LEDs
ARM: dts: sun7i: Add VE (Video Engine) module clock node
ARM: dts: sun4i: Add VE (Video Engine) module clock node
ARM: dts: sun8i: Add Orange Pi Plus support
ARM: dts: sunxi: Add Allwinner H3 DTSI
ARM: dts: sun7i: Add DRAM gates
ARM: dts: sun4i: Add DRAM gates
ARM: dts: sun9i: Add NMI controller device node
ARM: dts: sun9i: optimus: Enable Reduced Serial Bus controller
ARM: dts: sun9i: Add Reduced Serial Bus controller device node to A80 dtsi
ARM: dts: sun9i: optimus: Enable consumer IR receiver
ARM: dts: sun9i: Add consumer IR receiver device node and pinmux settings
ARM: dts: sun9i: optimus: Enable LED3
ARM: dts: sun9i: Add A80 R_PIO pin controller device node
ARM: dts: sun9i: Add TODO comments for the main and low power clocks
ARM: dts: sun9i: Add A80 PRCM clocks and reset control nodes
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- Select reset controller by default for Zynq
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlZutbsACgkQykllyylKDCGOjgCfWC/4Z3UmDAypeSEABmFaBkb2
uDkAn2VeuLBHYIZaEp3c22iVZ4X+xtbJ
=8W06
-----END PGP SIGNATURE-----
Merge tag 'zynq-soc-for-4.5' of https://github.com/Xilinx/linux-xlnx into next/soc
arm: Xilinx Zynq patches for v4.5
- Select reset controller by default for Zynq
* tag 'zynq-soc-for-4.5' of https://github.com/Xilinx/linux-xlnx:
ARM: zynq: Select ARCH_HAS_RESET_CONTROLLER
Signed-off-by: Olof Johansson <olof@lixom.net>
- Various small DT changes, GPIO, slcr, cpu label
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlZusi0ACgkQykllyylKDCFCDgCfQ0mCK4O38NMUHwG9wA4THD/e
54MAoJtiu6VVch3iJ7aMX7rcDPhQPQW9
=XrJB
-----END PGP SIGNATURE-----
Merge tag 'zynq-dt-for-4.5' of https://github.com/Xilinx/linux-xlnx into next/dt
arm: Xilinx Zynq dt patches for v4.5
- Various small DT changes, GPIO, slcr, cpu label
* tag 'zynq-dt-for-4.5' of https://github.com/Xilinx/linux-xlnx:
ARM: dt: zynq: Add labels to cpu nodes to allow overriding OPPs.
ARM: dts: zynq: describe SLCR as simple-mfd rather than simple-bus
ARM: dts: zynq: replace gpio-key,wakeup with wakeup-source property
ARM: zynq: DT: Add interrupt-controller property to GPIO
Signed-off-by: Olof Johansson <olof@lixom.net>
It's all very well providing an events directory to userspace that
details our events in terms of "event=0xNN", but if we don't define how
to encode the "event" field in the perf attr.config, then it's a waste
of time.
This patch adds a single format entry to describe that the event field
occupies the bottom 8 bits of our config field on ARMv7.
Signed-off-by: Will Deacon <will.deacon@arm.com>
This commit enables the touchscreen on TS-4800, using the ts4800-ts
driver.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This commit adds LCD support for the TS-4800. The panel is an Okaya
RS800480T-7X0WQ and the timings have been extracted from Technologic
Systems' tree.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Novena is an open-hardware laptop/desktop/bare board.
See http://www.kosagi.com/w/index.php?title=Novena_Main_Page
Signed-off-by: Sean Cross <xobs@kosagi.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Previously, the device tree mapped the FPGA like any other IPs inside
the SoC, but it is actually mapped through the WEIM (Wireless External
Interface Module). This patch updates the device tree to make use of it.
About the timings: in the image provided by the manufacturer, only
CS0GCR1 is changed. The other values are the default ones, but the WEIM
bindings expect them to be all explicitly set in the device tree, so I
just put the default values in the dt.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
These pins are actually not routed for UARTs, they should not be
reserved.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds the device nodes for 2D, 3D and VG GPU cores.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Added sata node to ls1021aqds and ls1021atwr board to support
sata function.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This device tree adds support for TS-4800 by Technologic Systems. This
board is based on MX51-babbage, but there are some subtle differences in
the pins used, and there is an additional FPGA that is memory-mapped.
More details here:
http://wiki.embeddedarm.com/wiki/TS-4800
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add Colibri standard pinmux for FlexCAN controller instances. CAN
is not a standard Colibri feature, but the datasheet predefines
pins which provide CAN (compatible across some modules). Hence,
add the pinmux on module level.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
No functional change, just moving the node to the place where it
belongs according to its unit address.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This allows for consistent numbering of the IPU output and
input ports.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This has been moved to the reg property where it belongs for quite some
time. The range has been unused by the kernel since then and with kernel
4.4 it's flagged as an unparsable range, as it does not comply to the
PCI ranges DT binding. Fix this by removing the superfluous range.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Audio IP need the spba clock, but original clock name "dma" is not
accurate, so change it to name "spba". The audio driver has been
using the new name "spba", the binding document has been updated.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Alison Wang <b18965@freescale.com>
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Jianwei Wang <jianwei.wang.chn@gmail.com>
Signed-off-by: Meng Yi <b56799@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Alison Wang <b18965@freescale.com>
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Jianwei Wang <jianwei.wang.chn@gmail.com>
Signed-off-by: Meng Yi <b56799@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As on i.MX7D, we using a virtual arm clk for CPU frequency
scaling, so correct the clocks info used by the cpufreq driver.
Signed-off-by: Bai Ping <b51503@freescale.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This addes support for SPI available on an off-board connector available on
some models of the GW52xx.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Ventana boards have an off-board connector with signals that can be pinmuxed
as either GPIO or PWM. This patch adds pwm device-tree nodes in the disabled
state which the bootloader can decide to enable based on bootloader config.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Minimal Cortex-M4 device tree to boot Linux to shell. M4 is booted via
Cortex-A5 running Linux using Stefan Agner's <stefan@agner.ch> "m4boot"
utility.
Signed-off-by: Afzal Mohammed <afzal.mohd.ma@gmail.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Extend the existing Vybrid DSPI devicetree implementation to also
describe the dspi2 and dspi3 functional blocks.
Signed-off-by: Cory Tusar <cory.tusar@pid1solutions.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This, together with the corresponding patch to pwm-imx.c, allows to order the
pwm devices correctly.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx6qdl.dtsi uses compatibles "fsl,imx6q-gpt", "fsl,imx31-gpt".
imx6dl.dtsi uses compatibles "fsl,imx6dl-gpt", "fsl,imx6q-gpt" since
commit
4e415ed814 (ARM: dts: imx6dl: add imx6dl gpt specific compatible string)
If imx6dl would be compatible with imx6q-gpt it would also have to be
compatible with imx31-gpt which is currently missing.
Based on the above mentioned patch I assume imx6q-gpt and imx6dl-gpt are
not compatible. So imx6q-gpt should be removed as compatible.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently it is not possible to have HDMI and LVDS working simultaneously,
because both ports try to use PLL5.
Move the LVDS clock parent to PLL3_USB_OTG, so that HDMI and LVDS can be
driven from independent sources.
With this change the LDB pixel clock goes to 68.57 MHz, which is still
within the valid range for the displays supported by the Ventana boards.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The GW54xx PMIC swbst regulator is used for LVDS power, CANbus xceiver
and HDMI DDC and is enabled by the bootloader. Set the regulator to
always-on so that Linux doesn't turn it off thinking its not needed.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds some values that are needed for an out-of-tree device
tree I'm currently working with.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Specify the 'adck-max-frequency' property in the adc nodes.
According to Documentation/devicetree/bindings/iio/adc/vf610-adc.txt
this is a recommended property.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It can improve the USB performance when choosing larger
burst size at some systems (bus size is larger), there is
no side effect if this burst size is larger than bus size.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
After setting ahb burst configuration as 0, we can increase tx/rx
burst size, it will improve the USB performance
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to commit 2503a5ecd8
"ARM: 6201/1: RealView: Do not use outer_sync() on ARM11MPCore
boards with L220" Some PB11MPCore RealView core tiles have broken
outer_sync.
We got rid of the custom barriers from the machine by disabling
outer sync, but that was just for the boardfile case. We have
to be able to do the same in the device tree case.
Since __l2c_init() is cloning and copying the L2C vtable,
we pass an argument to this function to optionally numb
the outer sync operation if desired, before initializing
the cache.
After this we can set up the cache correctly on the RealView
PB11MPCore. This was tested on a PB11MPCore known to have the
issue. Before this, spurious crashes would occur if we try to
set up the cache properly, after this it boots rock solid.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: devicetree@vger.kernel.org
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Having IPI_CPU_BACKTRACE as SGI15 may not work if the kernel is
running in non-secure mode and that the secure firmware has
decided to follow ARM's recommendations that SGI8-15 should
be reserved for secure purpose.
Now that we are "only" using SGI0-6, change IPI_CPU_BACKTRACE
to use SGI7, which makes it more likely to work.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since 9a46ad6d6d ("smp: make smp_call_function_many() use logic
similar to smp_call_function_single()"), the core IPI handling
has been simplified, and generic_smp_call_function_interrupt is
now the same as generic_smp_call_function_single_interrupt.
This means that one of IPI_CALL_FUNC and IPI_CALL_FUNC_SINGLE has
become redundant. We can then safely drop IPI_CALL_FUNC_SINGLE,
and use only IPI_CALL_FUNC.
This has the advantage of reducing the number of SGI IDs we're using
(a fairly scarse resource).
Tested on a dual A7 board.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The suspend() hook in the cpuidle_ops struct is always called on
the cpu entering idle, which means that the cpu parameter passed
to the suspend hook always corresponds to the local cpu, making
it somewhat redundant.
This patch removes the logical cpu parameter from the ARM
cpuidle_ops.suspend hook and updates all the existing kernel
implementations to reflect this change.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Lina Iyer <lina.iyer@linaro.org>
Tested-by: Lina Iyer <lina.iyer@linaro.org>
Tested-by: Jisheng Zhang <jszhang@marvell.com> [psci]
Cc: Lina Iyer <lina.iyer@linaro.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. Enable Maxim 8997 and 77693 family drivers (charger, extcon, LED,
RTC, haptic/motor, regulator).
2. Build ChromeOS EC drivers as modules on multi_v7.
3. Enable drivers important for Exynos4210-based Universal C210 board.
4. Enable NFSv4 client.
5. On exynos_defconfig set some options to a value recommended
by systemd. This also makes it more consistent with multi_v7.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ANuN
-----END PGP SIGNATURE-----
Merge tag 'samsung-defconfig-4.5' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/defconfig
Defconfig (exynos and multi_v7) changes for Exynos based boards for 4.5:
1. Enable Maxim 8997 and 77693 family drivers (charger, extcon, LED,
RTC, haptic/motor, regulator).
2. Build ChromeOS EC drivers as modules on multi_v7.
3. Enable drivers important for Exynos4210-based Universal C210 board.
4. Enable NFSv4 client.
5. On exynos_defconfig set some options to a value recommended
by systemd. This also makes it more consistent with multi_v7.
* tag 'samsung-defconfig-4.5' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: exynos_defconfig: Set recommended options for systemd
ARM: exynos_defconfig: Enable NFSv4 client
ARM: exynos_defconfig: Add drivers for Exynos4210 Universal C210 board
ARM: multi_v7_defconfig: Build ChromeOS EC drivers as modules
ARM: multi_v7_defconfig: Enable Maxim 77693 LED and haptic drivers
ARM: multi_v7_defconfig: Enable Maxim 8997 family drivers
ARM: exynos_defconfig: Enable Maxim 77693 LED and haptic drivers
ARM: exynos_defconfig: Enable Maxim 8997 family drivers
Signed-off-by: Olof Johansson <olof@lixom.net>
1. Switch from Exynos-specific restart/poweroff handler
(mach-exynos/pmu.c) to generic syscon-reboot and syscon-poweroff
drivers.
This depends on adding syscon nodes to DTS to preserve
bisectability.
2. Minor improvements.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=JWjG
-----END PGP SIGNATURE-----
Merge tag 'samsung-soc-4.5' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/soc
Samsung Exynos improvements for 4.5:
1. Switch from Exynos-specific restart/poweroff handler
(mach-exynos/pmu.c) to generic syscon-reboot and syscon-poweroff
drivers.
This depends on adding syscon nodes to DTS to preserve
bisectability.
2. Minor improvements.
* tag 'samsung-soc-4.5' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: EXYNOS: Remove redundant code from regs-pmu.h
ARM: EXYNOS: Constify local exynos_pmu_data structure
ARM: EXYNOS: Switch to syscon reboot and poweroff
ARM: dts: Add syscon-{reboot, poweroff} nodes for exynos5410
ARM: dts: Add syscon-{reboot, poweroff} nodes for exynos5
ARM: dts: Add syscon-{reboot, poweroff} nodes for exynos4
ARM: dts: Add syscon-{reboot, poweroff} nodes for exynos3250
Signed-off-by: Olof Johansson <olof@lixom.net>
handlers on Exynos boards. The mach-exynos changes must base on top
of this to retain the bisectability of not loosing reboot/poweroff
features.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/NF/
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-syscon-restart-4.5' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Device Tree changes adding necessary nodes for syscon reboot/poweroff
handlers on Exynos boards. The mach-exynos changes must base on top
of this to retain the bisectability of not loosing reboot/poweroff
features.
* tag 'samsung-dt-syscon-restart-4.5' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: Add syscon-{reboot, poweroff} nodes for exynos5410
ARM: dts: Add syscon-{reboot, poweroff} nodes for exynos5
ARM: dts: Add syscon-{reboot, poweroff} nodes for exynos4
ARM: dts: Add syscon-{reboot, poweroff} nodes for exynos3250
Signed-off-by: Olof Johansson <olof@lixom.net>
The development kit uses a TSC2004 chip attached to I2C3.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Empire Electronix D709 tablet is a fairly standard 7" A13 tablet,
featuring usb-wifi, a micro-sd slot, micro-usb otg and headphone jack.
Empire Electronix is written on the back of the tablet, the D709 model
info can be found in the about tablet menu in android.
The PCB has no markings to speak of.
This dts file does not add support for the ft5x touchscreen found at
i2c bus 1, addr 0x38, irq PG11, because it does not work out of the box.
It seems it has been flashed with the wrong firmware and needs to have
alternative firmware uploaded at boot to make the touchscreen work
properly, when hot-booting from android into an upstream kernel the
touchscreen does work.
The Memsic MXC622X accelerometer at i2c bus 1, addr 0x15 also is not
enabled as there is no driver for it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Wits Pro A20 DKT has a gbit ethernet port, enable it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This commit enables the on-chip audio codec present on the MK808C.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This commit enables the on-chip audio codec present on some variants
of the MK802.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add PA gpio pin for controlling power of two external amplifiers (NS4890) which are used on the Wexler TAB7200 tablet
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a backlight for controlling the lcd panel backlight on Wexler TAB7200 tablet
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a node for the Goodix GT911 touchscreen found on the Wexler TAB7200 tablet
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
If Linux is running as dom0, call XENPF_settime64 to update the system
time in Xen on pvclock_gtod notifications.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Read the wallclock from the shared info page at boot time.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The hypervisor actually exposes an additional field to struct
pvclock_wall_clock, with the high 32 bit seconds.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: Julien Grall <julien.grall@citrix.com>
Register the runstate_memory_area with the hypervisor.
Use pv_time_ops.steal_clock to account for stolen ticks.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Introduce CONFIG_PARAVIRT and PARAVIRT_TIME_ACCOUNTING on ARM.
The only paravirt interface supported is pv_time_ops.steal_clock, so no
runtime pvops patching needed.
This allows us to make use of steal_account_process_tick for stolen
ticks accounting.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Christopher Covington <cov@codeaurora.org>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Russell King <linux@arm.linux.org.uk>
The Versatile Industrial Communication platform is a community oriented
board from Landis + Gyr. It comes with:
- an RS-485 port
- 2 Ethernet ports
- a wireless M-BUS
- a 4G modem
- a 4MB SPI flash
- a 4GB eMMC
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The i.MX7 Kconfig option had a couple of missing select lines that
I fixed already, but I missed HAVE_IMX_SRC:
arch/arm/mach-imx/built-in.o: In function `imx7d_init_irq':
platform-spi_imx.c:(.init.text+0x25a8): undefined reference to `imx_src_init'
This adds that one as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 0be5da9dc2 ("ARM: imx: imx7d requires anatop")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The socfpga.dtsi explicitly enabled MMC support, but not all boards are
equiped with an MMC card. There are setups which only have QSPI NOR.
Therefore, disable the MMC support on socfpga.dtsi level and enable it
on per-board basis.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alan Tull <atull@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Olof Johansson <olof@lixom.net>
Cc: Thor Thayer <tthayer@altera.com>
Cc: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Enable TPS65217 regulator to have rootfs in MMC for Beagle Bone's.
Suggested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Afzal Mohammed <afzal.mohd.ma@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The UniPhier SoCs support pinctrl drivers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patchset is the initiation version to try work
for kylin board.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
In general, the sdio/sdmmc is used by the wifi module
and sd card.
let's add the node for these function.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The pinctrl gpio pull up/down is incorrect since the rk3036 SoCs
can't set the status in the internal.
We should keep the default status for enable the gpio status,
In fact, the pull_none is the disable the gpio pull up/down.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Looks like we're missing the wakeirq for the console uart for
duovero parlor. Let's add that as without it console acess just
hangs with PM enabled.
Cc: Arun Bharadwaj <arun@gumstix.com>
Cc: Ash Charles <ash@gumstix.com>
Cc: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Wexler TAB7200 tablet use channel 0 of the PWM controller for backlight dimming
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
PA GPIO pin (PH15) controls power to external amplifier (FT2012Q).
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The pov protab2-ips9 tablet uses the A10's integrated audio codec,
enable it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The UTOO P66 tablet uses the A13's integrated audio codec, enable it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add qspi memory mapped region entries for AM43xx based SoCs. Also,
update the binding documents for the controller to document this change.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add qspi memory mapped region entries for DRA7xx based SoCs. Also,
update the binding documents for the controller to document this change.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The realview multiplatform series has a trivial conflict with
one of the treewide cleanups, let's just merge that in to
avoid having to resolve this later.
* treewide/cleanup:
ARM: use "depends on" for SoC configs instead of "if" after prompt
ARM/clocksource: use automatic DT probing for ux500 PRCMU
ARM: use const and __initconst for smp_operations
ARM: hisi: do not export smp_operations structures
Conflicts:
arch/arm/mach-integrator/Kconfig
The platsmp-dt.c file does not build when CONFIG_SMP is disabled:
platsmp-dt.c:84:2: error: unknown field 'smp_prepare_cpus' specified in initializer
This changes the Makefile to build it conditionally on CONFIG_SMP.
The legacy platsmp.c file is only used for ATAGS based builds, so
we can move it into the CONFIG_ATAGS conditional.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Now that we have multiplatform support, let the RealView
defconfigs select all the RealView boards so we boot out of
the box like before. This updates both defconfigs.
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Tested on the ARM PB11MPCore
- Tested with boardfile boot
- Tested with DeviceTree boot
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tfk1
-----END PGP SIGNATURE-----
Merge tag 'realview-multiplatform-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/multiplatform
Pull "Multiplatform support for the RealView" from Linus Walleij:
Here is the result of my application of the second part of Arnds
patchset, actually enabling multiplatform and getting the RealView
off the ground as a multiplatform target.
It is dependent on an outstanding patch to the irqchips tree bumping
the number of GICs to 2 for the RealView platform. I cannot say I will
be sleepless if these go in side by side: each branch will compile but
will not boot until both trees have been pulled hurting bisectability a
bit.
- Tested on the ARM PB11MPCore
- Tested with boardfile boot
- Tested with DeviceTree boot
* tag 'realview-multiplatform-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: realview: select apropriate targets
ARM: realview: clean up header files
ARM: realview: make all header files local
ARM: no longer make CPU targets visible separately
ARM: integrator: use explicit core module options
ARM: realview: enable multiplatform
Now that we have multiplatform support, let the RealView
defconfigs select all the RealView boards so we boot out of
the box like before. This updates both defconfigs.
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This contains multiple trivial cleanups to the realview headers:
- removing the file names from the introductory comment
- removing the uncompress.h header that is unused
- removing the irqs.h header and NR_IRQS logic that is
obsoleted by sparse IRQs
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Nothing includes these files any more, so we can simply move them
from arch/arm/mach-realview/include/mach/ to arch/arm/mach-realview.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[Two fixes added to make everything compile]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that realview and integrator always select the correct CPU
type themselves based on the core tiles, there is no need to
still have them user-visible in arch/arm/mm/Kconfig. The
ARM925T symbol has been selected by the only user for many
years, so that can be removed along with the realview and
integrator specific ones.
This also solves randconfig build problems on realview.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For consistency with the other platforms, this remove the CPU
selection logic in mm/Kconfig that was only used by integrator,
and adds specific options for each available core tile and core
module, which in turn select the correct CPUs.
This is consistent with the new way that we do it for realview
and all other platforms.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
All obstacles are out of the way by now, so we can finally move realview
to multiplatform.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
[Rebased Kconfig, fixed if $(X) to if X in Makefile]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For whatever reason, this patch was not applied verbatim and had all
tabs replaced with spaces. Replace them back by a quick sed.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alan Tull <atull@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: Thor Thayer <tthayer@altera.com>
Cc: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Before commit 662d971584
("arm/arm64: KVM: Kill CONFIG_KVM_ARM_{VGIC,TIMER}") is was possible to
compile the kernel without vGIC and vTimer support. Commit message says
about possibility to detect vGIC support in runtime, but this has never
been implemented.
This patch introduces runtime check, restoring the lost functionality.
It again allows to use KVM on hardware without vGIC. Interrupt
controller has to be emulated in userspace in this case.
-ENODEV return code from probe function means there's no GIC at all.
-ENXIO happens when, for example, there is GIC node in the device tree,
but it does not specify vGIC resources. Any other error code is still
treated as full stop because it might mean some really serious problems.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The ARMv8.1 architecture extension allows to choose between 8-bit and
16-bit of VMID, so use this capability for KVM.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
kvm_arm.h is included from both C code and assembly code; however some
definitions in this header supplied with U/UL/ULL suffixes which might
confuse assembly once they got evaluated.
We have _AC macro for such cases, so just wrap problem places with it.
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Since commit a987370 ("arm64: KVM: Fix stage-2 PGD allocation to have
per-page refcounting") there is no reference to S2_PGD_ORDER, so kill it
for the good.
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
David Binderman reported that the exception injection code had a
couple of unused variables lingering around.
Upon examination, it looked like this code could do with an
anticipated spring cleaning, which amounts to deduplicating
the CPSR/SPSR update, and making it look a bit more like
the architecture spec.
The spurious variables are removed in the process.
Reported-by: David Binderman <dcb314@hotmail.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Revert 6f0f6c40b66 ("ARM: dts: Set VAUX1 and VAUX4 on Logic PD Torpedo")
because it It was already done and it's just a duplicate. See:
2d11961f3e ("ARM: dts: Set VAUX1 and VAUX4 to 3.0V and 1.8V respectively")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The 'fixes' branch contains d5d4fdd86f ("irqchip/versatile-fpga:
Fix PCI IRQ mapping on Versatile PB") that is required for booting
the versatile platform prior to the rework in this branch, but
including both causes a build-time error.
I'm doing an evil merge here to pull in the fixes branch so we have
that commit included but at the same time revert the trivial change.
This gives us a bisectable history.
* fixes: (22 commits)
fsl-ifc: add missing include on ARM64
ls2080a/dts: Add little endian property for GPIO IP block
dt-bindings: define little-endian property for QorIQ GPIO
ARM64: dts: ls2080a: fix eSDHC endianness
ARM: dts: vf610: use reset values for L2 cache latencies
ARM: pxa: use PWM lookup table for all machines
ARM: dts: berlin: add 2nd clock for BG2Q sdhci0 and sdhci1
ARM: dts: berlin: correct BG2Q's sdhci2 2nd clock
ARM: dts: am4372: fix clock source for arm twd and global timers
ARM: at91: fix pinctrl driver selection
ARM: at91/dt: add always-on to 1.8V regulator
ARM: dts: vf610: fix clock definition for SAI2
ARM: imx: clk-vf610: fix SAI clock tree
ARM: ixp4xx: fix read{b,w,l} return types
irqchip/versatile-fpga: Fix PCI IRQ mapping on Versatile PB
ARM: OMAP2+: enable REGULATOR_FIXED_VOLTAGE
ARM: dts: add dm816x missing spi DT dma handles
ARM: dts: add dm816x missing #mbox-cells
cpufreq: s3c24xx: Do not mark s3c2410_plls_add as __init
bus: sunxi-rsb: unlock on error in sunxi_rsb_read()
...
Pull libnvdimm fixes from Dan Williams:
- Two bug fixes for misuse of PAGE_MASK in scatterlist and dma-debug.
These are tagged for -stable. The scatterlist impact is potentially
corrupted dma addresses on HIGHMEM enabled platforms.
- A minor locking fix for the NFIT hot-add implementation that is new
in 4.4-rc. This would only trigger in the case a hot-add raced
driver removal.
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
dma-debug: Fix dma_debug_entry offset calculation
Revert "scatterlist: use sg_phys()"
nfit: acpi_nfit_notify(): Do not leave device locked
Make sure to tell the kernel that AM437x devices have ARM TWD timer.
Signed-off-by: Felipe Balbi <balbi@ti.com>
[grygorii.strashko@ti.com: drop ARM Global timer selection, because
it's incompatible with PM (cpuidle/cpufreq). So, it's unsafe to enable
it unconditionally]
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
System will misbehave in the following case:
- AM43XX only build (UP);
- CONFIG_CPU_IDLE=y
- ARM TWD timer enabled and selected as clockevent device.
In the above case, It's expected that broadcast timer will be used as
backup timer when CPUIdle will put MPU in low power states where ARM
TWD will stop and lose its context. But, the CONFIG_SMP might not be
selected when kernel is built for AM43XX SoC only and, as result,
GENERIC_CLOCKEVENTS_BROADCAST option will not be selected also. This
will break CPUIdle and System will stuck in low power states.
Hence, fix it by selecting GENERIC_CLOCKEVENTS_BROADCAST option for
AM43XX SoCs always and add empty tick_broadcast() function
implementation - no need to send any IPI on UP. After this change
timer1 will be selected as broadcast timer the same way as for SMP,
and CPUIdle will work properly.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The omap-pcm in ASoC is no longer a platform device. No need to create this
device anymore.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The omap-pcm in ASoC is no longer a platform device. No need to create this
device anymore.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Bindings for the WL1283 Bluetooth was removed from the shared transport
driver in commit c0bd1b9e58 ("Revert ti-st: add device tree support")
Until we havea better binding, we need to use the platform data to
initialize Bluetooth.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add basic support for Logic PD type 15 display for older development kits.
This uses GPIO for the backlight.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
bluetooth HW is WLS1271 chip connected to UART1.
Device tree modifications:
- Pinmux for UART1.
- Pinmux for bluetooth enable GPIO.
Bluetooth enable GPIO is set to enable during startup by setting the
relevant pinmux pin to pull-up.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pinmux configuration for DVI/LCD.
Add DRM display driver node with timing configurations for DVI and LCD.
Add I2C GPIOs configurations for DVI and LCD enable.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The I2C GPIO expander (PCA9555) adds 16 GPIOs to the module.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add basic support for the SBC-T335.
CompuLab SBC-T335 is a single baseboard computer.
The SBC-T335 is based on the Texas Instruments Cortex-A8 Sitara AM3354
SoC.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Though the keyboard and other driver will continue to support the legacy
"gpio-key,wakeup", "linux,wakeup" boolean property to enable the wakeup
source, "wakeup-source" is the new standard binding.
This patch replaces all the legacy wakeup properties with the unified
"wakeup-source" property in order to avoid any futher copy-paste
duplication.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Though the keyboard driver for GPIO buttons(gpio-keys) will continue to
check for/support the legacy "gpio-key,wakeup" boolean property to
enable gpio buttons as wakeup source, "wakeup-source" is the new
standard binding.
This patch replaces the legacy "gpio-key,wakeup" with the unified
"wakeup-source" property in order to avoid any futher copy-paste
duplication.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Switch to use the ti,edma3-tpcc and ti,edma3-tptc binding for the eDMA3 and
enable the DMA even crossbar with ti,am335x-edma-crossbar.
With the new bindings boards can customize and tweak the DMA channel
priority to match their needs. With the new binding the memcpy is safe
to be used since with the old binding it was not possible for a driver
to know which channel is allowed to be used as non HW triggered channel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Switch to use the ti,edma3-tpcc and ti,edma3-tptc binding for the eDMA3 and
enable the DMA even crossbar with ti,am335x-edma-crossbar.
With the new bindings boards can customize and tweak the DMA channel
priority to match their needs. With the new binding the memcpy is safe
to be used since with the old binding it was not possible for a driver
to know which channel is allowed to be used as non HW triggered channel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Moving ARCH_VERSATILE into ARCH_MULTIPLATFORM means that it no longer
works as the default target for MMU-less kernels. While we might
want to get that working again in the future, it's also a rather
bad default, and it makes sense to make ARM_SINGLE_V7M the default
because that is what realistically all NOMMU users on ARM are using,
and it actually is what gets selected by default in the absence of
versatile in the choice statement.
Related to this, 'allnoconfig' kernels fail to link with the new
default, as they do not include a machine record:
arm-linux-gnueabi-ld: no machine record defined
For ARCH_MULTIPLATFORM kernels, we avoid this error by using a
default machine descriptor that works for all trivial platforms,
like ARCH_VIRT. The same reasoning applies for ARM_SINGLE_V7M,
as that can also boot with empty machine descriptors both on
qemu and on real hardware, as long as all the drivers are present.
We could also follow up with a patch to remove the existing
machine descriptors for the ARMv7M platforms, the only callback
pointer the four platforms contain today is the armv7m_restart
handler and we can simply make that the default for v7M with an
add-on patch.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
I accidentally move the DEBUG_LL_UART_EFM32 option when sorting all
other options alphanumerically, but it belongs into the same group
as DEBUG_LL_UART_8250 and DEBUG_LL_UART_PL01X.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 1dc9341 ("ARM: debug-ll: reorder Kconfig alphanumerically")
The debug-ll infrastructure can be configured in two ways, either
by selecting a platform specific debug option, or by picking one
of the generic options (8250 or pl01x typically). For compatibility
with multiplatform kernels, we have changed a couple of platforms
to use the former method now when they used to use the latter.
Unfortunately, this broke the defconfigs because now they still
enable CONFIG_DEBUG_LL_UART_PL01X or CONFIG_DEBUG_LL_UART_8250,
and we no longer configure the correct register addresses
automatically.
Embarrassingly, this was only found in linux-next when the
defconfig builds turned up errors for multiple people, and I
had not caught those in my own tests, which were done using
the randconfig fixes patchset on top, and that has a workaround
to avoid a build error when the addresses are not configured.
The error was something like:
.config:2010:warning: symbol value '' invalid for DEBUG_UART_PHYS
.config:2011:warning: symbol value '' invalid for DEBUG_UART_VIRT
This patch avoids the problem by removing the respective
statements from the defconfig files. Any out of tree defconfig
files on the platforms I have changed will have to do the same
change or run into the build error above. Any users that have
a full .config already set the correct DEBUG_UART_PHYS/VIRT
addresses and do not need to change anything.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 4db22c1 ("ARM: debug-ll: rework integrator/versatile handling")
Fixes: f06455f ("ARM: debug-ll: rework ep93xx handling")
Fixes: c047f52 ("ARM: debug-ll: reorganize mvebu debug uart config")
Fixes: 59bd4c3 ("ARM: debug-ll: rework lpc32xx handling")
The ARM compiler inserts calls to __aeabi_idiv() and
__aeabi_uidiv() when it needs to perform division on signed and
unsigned integers. If a processor has support for the sdiv and
udiv instructions, the kernel may overwrite the beginning of those
functions with those instructions and a "bx lr" to get better
performance.
To ensure that those functions are aligned to a 32-bit word for easier
patching (which might not always be the case in Thumb mode) and that
the two patched instructions end up in the same cache line, a 8-byte
alignment is enforced when ARM_PATCH_IDIV is selected.
This was heavily inspired by a previous patch from Stephen Boyd.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Signed-off-by: Prasanna Karthik <mkarthi3@visteon.com>
Signed-off-by: Nathan Lynch <nathan_lynch@mentor.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The proc-v7.S code uses a small temporary stack to preserve register
content in its setup code. This stack is located in the .text section
which is normally meant to be read-only.
Move that temporary stack to the .bss section and get its address in
a position independent way, similarly to what we do in other parts
of the kernel.
While at it, one comments was updated to reflect reality, and the list
of saved registers in the proc-v7.S case is updated to match the comment
next to it for coherency.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The newly added rk3036 smp operations missed the wholesale fixup from
Masahiro Yamada. So fix that now.
Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Enable some ssbi drivers present on msm8660, msm8960 and apq8064
devices so that we fully exercise the devices present in the dts
files.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Pull ARM fixes from Russell King:
"Further ARM fixes:
- Anson Huang noticed that we were corrupting a register we shouldn't
be during suspend on some CPUs.
- Shengjiu Wang spotted a bug in the 'swp' instruction emulation.
- Will Deacon fixed a bug in the ASID allocator.
- Laura Abbott fixed the kernel permission protection to apply to all
threads running in the system.
- I've fixed two bugs with the domain access control register
handling, one to do with printing an appropriate value at oops
time, and the other to further fix the uaccess_with_memcpy code"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8475/1: SWP emulation: Restore original *data when failed
ARM: 8471/1: need to save/restore arm register(r11) when it is corrupted
ARM: fix uaccess_with_memcpy() with SW_DOMAIN_PAN
ARM: report proper DACR value in oops dumps
ARM: 8464/1: Update all mm structures with section adjustments
ARM: 8465/1: mm: keep reserved ASIDs in sync with mm after multiple rollovers
This enables smem, smd, rpm, regulators, pmic pinctrl and hwspinlock as
these platform features are now merged. It enables gpio-keys as this is
used by most boards and enables fhandle and cgroups, so we can boot
systemd.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds support for the PMA8084 regulators found on APQ8084
platforms.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
This patch adds support for RPM and SMD nodes that are present on APQ8084
platforms.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
This patch adds all the required nodes to support SMEM on APQ8084
Signed-off-by: Andy Gross <agross@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
GSBI6 UART module is connected to BT chip, which uses
hardware flow control lines. Enable them on SoC side.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Currently the rates of the xo and sleep clocks are hard-coded in the
GCC driver, but this is a board layout description that actually should
be in the DT. Moving them into DT also allows us to insert the RPM
controlled clocks between the DT and GCC clocks.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
- orion5x/mv78xx0 multiplatform conversion
- legacy dove PMU support conversion
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlZq1uEACgkQCwYYjhRyO9XZ8ACdHuhMhzgLQ3lR/wUj0Eaj6udh
AuMAn2JdAcBRYkI6B0PkPK5igJugASzQ
=pkme
-----END PGP SIGNATURE-----
Merge tag 'mvebu-soc-4.5-1' of git://git.infradead.org/linux-mvebu into next/multiplatform
Merge "mvebu soc for 4.5 (part 1)" from Gregory CLEMENT:
- orion5x/mv78xx0 multiplatform conversion
- legacy dove PMU support conversion
* tag 'mvebu-soc-4.5-1' of git://git.infradead.org/linux-mvebu:
ARM: dove: convert legacy dove to PMU support
soc: dove: add legacy support to PMU driver
ARM: orion5x: multiplatform support
ARM: orion5x: clean up mach/*.h headers
ARM: mv78xx0: multiplatform support
ARM: mv78xx0: clean up mach/*.h headers
ARM: orion: use SPARSE_IRQ everywhere
ARM: orion: always use MULTI_IRQ_HANDLER
ARM: orion: move watchdog setup to mach-orion5x
Conflicts:
arch/arm/Kconfig
arch/arm/mach-dove/include/mach/entry-macro.S
arch/arm/mach-orion5x/include/mach/entry-macro.S
multiplatform and extended DT support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Zhx3
-----END PGP SIGNATURE-----
Merge tag 'realview-base-armsoc-1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/multiplatform
Merge "Realview multiplatform support" from Linus Walleij:
The board and infrastructure changes for RealView
multiplatform and extended DT support.
* tag 'realview-base-armsoc-1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: realview: add an DT SMP boot method
ARM: realview: select SP810 and ICST for the DT variant
soc: versatile: add support for the PB11MPCore
clk: versatile-icst: add device tree support
clk: versatile-icst: refactor to allocate regmap separately
clk: versatile-icst: convert to use regmap
ARM: realview: remove private barrier implementation
ARM: no longer force unbuffered DMA for realview
clk/realview: stop using machine headers
ARM: realview: don't map undefined PCI registers
ARM: realview: remove sparsemem hack
Conflicts:
drivers/clk/versatile/Kconfig
in mainline kernel with it's bootloader configured clocks. However,
trying to boot dm814x-evm uncovered all kind of issues with the timer
clock. To keep t410 booting, these issues need to be fixed in a specific
order and this branch contains both device tree and code changes.
To summarize the changes, we had missing ranges for clocks to probe,
missing aliase for clocks, wrong registers for divder clocks, and bad
address for the control module. All these went unnoticed earlier as
things worked without errors by luck and I did not pay much attention
to them until I got hold of a dm814x-evm and I noticed it did not boot.
As these are fixes for features that never worked, these can wait for
v4.5 merge window no problem.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Mesm
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.5/81xx-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/fixes-non-critical
Merge "omap fixes for 81xx for v4.5 merge window" from Tony Lindgren:
Fixes for ti81xx for v4.5 merge window. We have hp t410 already booting
in mainline kernel with it's bootloader configured clocks. However,
trying to boot dm814x-evm uncovered all kind of issues with the timer
clock. To keep t410 booting, these issues need to be fixed in a specific
order and this branch contains both device tree and code changes.
To summarize the changes, we had missing ranges for clocks to probe,
missing aliase for clocks, wrong registers for divder clocks, and bad
address for the control module. All these went unnoticed earlier as
things worked without errors by luck and I did not pay much attention
to them until I got hold of a dm814x-evm and I noticed it did not boot.
As these are fixes for features that never worked, these can wait for
v4.5 merge window no problem.
* tag 'omap-for-v4.5/81xx-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Remove useless check for legacy booting for dm814x
ARM: OMAP2+: Enable GPIO for dm814x
ARM: dts: Fix dm814x pinctrl address and mask
ARM: dts: Fix dm8148 control modules ranges
ARM: OMAP2+: Fix timer entries for dm814x
ARM: dts: Fix some mux and divider clocks to get dm814x-evm booting
ARM: OMAP2+: Add DPPLS clock manager for dm814x
clk: ti: Add few dm814x clock aliases
ARM: dts: Fix dm814x entries for pllss and prcm
support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=De8M
-----END PGP SIGNATURE-----
Merge tag 'realview-base-armsoc-2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/dt
Merge "Realview DT files" from Linus Walleij:
The device tree changes for the continued RealView DT
support.
* tag 'realview-base-armsoc-2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: realview: add device tree for PB11MPCore
clk: add ARM syscon ICST device tree bindings
ARM: add DT bindings for the ARM11MPCore CPU cluster
Merge "ARM Versatile multi-platform support" from Rob Herring:
Arnd lit a fire under me to dust this off and get it merged. So here it
is. The main change from prior version is I merged all the code to a
single file. It's a bigger patch than I'd like, but I don't think trying
to do it in multiple steps is worth it.
This is dependent on some solution for the default platform choice on
!MMU builds (allnoconfig) as it can't be Versatile after this series.
Arnd has some ideas on how to address that.
This is tested under QEMU. Linus previously tested this on actual h/w
and had a problem with the display identification which needs
investigation or agreement to worry about it if and when someone
actually cares.
* versatile/multiplatform:
ARM: versatile: convert to multi-platform
ARM: versatile: merge mach code into a single file
ARM: versatile: switch to DT only booting and remove legacy code
ARM: versatile: add DT based PCI detection
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Now that all the prerequisites are in place, we can enable Versatile
boards for multi-platform kernels.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
With DT-only support now in place and most of the legacy code removed,
the separation of core.c and versatile_dt.c makes little sense. The
headers in mach include directory also have to move for multi-platform
support, but with a single .c file the remaining definitions needed can
also be moved into the versatile_dt.c.
In the move, the system registers and IB2 registers are converted to
run-time mappings and all register accesses converted to use
readl/writel.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
With DT support for clocks, irqchips, timers, and PCI now in place, DT
based booting has feature parity with non-DT legacy boot. The final
piece is actually enabling common clock support on Versatile. Enabling
full DT support requires either removing the old Versatile clock code,
updating the legacy boot to use the common clock code, or making DT and
legacy boot mutually exclusive. Given that removing legacy boot code is
the goal anyway, I am going with the 1st option.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Disable the Versatile PCI DT node when no PCI backplane is detected. This
will prevent the Versatile PCI driver from probing when PCI is not
populated.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The ezx platform contains multiple machine descriptors, but not all
of them use all of the data structures, and it's possible to disable
all of the machines, which produces some harmless warnings:
mach-pxa/ezx.c:53:26: warning: 'ezx_pwm_lookup' defined but not used [-Wunused-variable]
mach-pxa/ezx.c:86:31: warning: 'ezx_fb_info_1' defined but not used [-Wunused-variable]
mach-pxa/ezx.c:107:31: warning: 'ezx_fb_info_2' defined but not used [-Wunused-variable]
mach-pxa/ezx.c:113:32: warning: 'ezx_devices' defined but not used [-Wunused-variable]
mach-pxa/ezx.c:117:22: warning: 'ezx_pin_config' defined but not used [-Wunused-variable]
This marks all those structures as __maybe_unused to avoid the warnings.
Obviously a configuration that contains the ezx platform but no specific
model is a bit silly, but it should not cause compile-time warnings.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
The raumfeld.c file contains three similar machine definitions,
each with their own init function. If one or more of them are
disabled, we get compile-time warnings:
arm/mach-pxa/raumfeld.c:1070:123: warning: 'raumfeld_connector_init' defined but not used [-Wunused-function]
arm/mach-pxa/raumfeld.c:1082:123: warning: 'raumfeld_speaker_init' defined but not used [-Wunused-function]
This marks the functions as __maybe_unused to avoid the warnings.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Daniel Mack <daniel@zonque.org>
In an old commit, we worked around the duplicate definition of
GPIO24_SSP1_SFRM in cm-x2xx.c, which includes files for both
pxa25x and pxa27x. Apparently the problem has come back and we
now have four additional duplicate symbols that cause warnings:
In file included from /git/arm-soc/arch/arm/mach-pxa/pxa27x.h:7:0,
from /git/arm-soc/arch/arm/mach-pxa/cm-x2xx.c:27:
/git/arm-soc/arch/arm/mach-pxa/mfp-pxa27x.h:21:0: warning: "GPIO86_GPIO" redefined
#define GPIO86_GPIO MFP_CFG_IN(GPIO86, AF0)
This uses the same hack as before and undefines all symbols that
are defined more than once. Fortunately, cm-x2xx does not need
any of these.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
* s3c64xx/multiplatform:
ARM: s3c64xx: allow building without board support
ARM: s3c64xx: multiplatform support
ARM: s3c64xx: use common debug-ll implementation
ARM: s3c64xx: use new adc/touchscreen driver
iio: exynos-adc: add experimental touchscreen support
ARM: s3c64xx: enable sparse IRQ support
ARM: s3c64xx: prepare initcalls for multiplatform
gpio: samsung: move gpio-samsung driver back to platform code
ASoC: samsung/smartq: use dynamic registration
Input: s3c2410_ts: fix S3C_ADC dependency
Conflicts:
arch/arm/Kconfig.debug
The file has gotten a little out of sync, as platforms got
added in the wrong place, or have been renamed. This moves
the options around, but should not change any functionality.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Footbridge has two debug ports that are handled a bit differently:
The 8250 port uses the normal debug/8250.S implementation that is shared
with a lot of other platforms, but it relies on the DEBUG_UART_8250
option to be turned on automatically instead of being selected by
DEBUG_FOOTBRIDGE_COM1 as we do for most other platforms. I'm changing
this to use a 'select' and change the dependency to the debug symbol
rather than the platform symbol for consistency.
The DC21285 UART has a separate top-level option, and relies on
the traditional include/mach/debug-macro.S method. With the s3c64xx
multiplatform series queued up for 4.5, it is now the last one that does
this, so by moving this file to include/debug/dc21285.S, we can get
all platforms to do things the same way.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
LPC32xx can not yet be configured in a multiplatform kernel, but
if we ever get there, enabling one of the LPC32xx platforms
while trying to use DEBUG_LL for another platform can default to
the wrong UART address, as the options are purely based on the
architecture being enabled or not.
This changes the logic to use the LPC32xx default addresses only
if we have also picked the respective Kconfig symbols introduced
here.
While we're at it, this also reorders the virtual address as
it should be.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Gemini can not yet be configured in a multiplatform kernel, but
if we ever get there, enabling one of the gemini platforms
while trying to use DEBUG_LL for another platform can default to
the wrong UART address, as the options are purely based on the
architecture being enabled or not.
This changes the logic to use the gemini default addresses and
the flow control settings only if we have also picked the respective
Kconfig symbols introduced here.
While we're at it, this also reorders the virtual address as
it should be.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Enabling one of the integrator platforms in a multiplatform kernel
while trying to use DEBUG_LL for another platform can default to
the wrong UART address, as the options are purely based on the
architecture being enabled or not.
This changes the logic to use the integrator default addresses only
if we have also picked the respective Kconfig symbols introduced
here. Versatile is not yet part of multiplatform, but hopefully
soon will be, so we do the same change for versatile as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Enabling one of the SPEAr platforms in a multiplatform kernel
while trying to use DEBUG_LL for another platform can default to
the wrong UART address, as the options are purely based on the
architecture being enabled or not.
This changes the logic to use the SPEAr default addresses only
if we have also picked the respective Kconfig symbols introduced
here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This makes ep93xx debug-ll handling more consistent with the other
platforms, by adding a separate Kconfig symbol for it that
in turn selects the standard DEBUG_UART_PL01X symbol.
We still have to pick a physical address even if DEBUG_LL is disabled
here, because the EP93xx uncompress output code uses
CONFIG_DEBUG_UART_PHYS. If we ever move to multiplatform support,
this can go away.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
As we are moving dove/mv78xx0/orion into multiplatform, the debug-ll
configuration options for these platforms are conflicting with the
multiplatform configuration: enabling one of those platforms sometimes
changes the default addresses to the ones used on one of them, rather
than the one that was selected in Kconfig.
This changes the configuration so we share the physical address
configuration with mach-mvebu.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
We may have multiple platforms enabled and also DEBUG_LL
configured for one of them. However if we enable ARCH_KEYSTONE,
we default to using 32-bit UART access independent of which
platform we are actually using, which can be confusing.
This changes the logic so the 32-bit default gets only
used by default if we actually configure the keystone
UART, as opposed to picking some other 8250 setting on
a kernel that has keystone support enabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
commit db0fa0cb01 "scatterlist: use sg_phys()" did replacements of
the form:
phys_addr_t phys = page_to_phys(sg_page(s));
phys_addr_t phys = sg_phys(s) & PAGE_MASK;
However, this breaks platforms where sizeof(phys_addr_t) >
sizeof(unsigned long). Revert for 4.3 and 4.4 to make room for a
combined helper in 4.5.
Cc: <stable@vger.kernel.org>
Cc: Jens Axboe <axboe@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Fixes: db0fa0cb01 ("scatterlist: use sg_phys()")
Suggested-by: Joerg Roedel <joro@8bytes.org>
Reported-by: Vitaly Lavrov <vel21ripn@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Merge "Broadcom soc changes for v4.5" from Florian Fainelli:
This pull request contains Broadcom SoC changes for 4.5, with the following changes:
- Lucas Stach removes the workaround for an imprecise fault for Broadcom
BCM5301x SoCs (Northstar) since this is now handled by the ARM/Linux kernel
directly
- Hauke Merthens enables a bunch of erratas for the Cortex-A9 and PL310 L2
cache present on early Northstar chips (BCM4708)
- Kapil Hali adds SMP support for the Northstar Plus SoCs by consolidating the
existing SMP code for Kona SoCs (mobile platforms), fixng the Device Tree
binding for the Kona platforms (wrong placement for 'enable-method' and
'secondary-reg') and then finally adds the functional code for the Northstar
Plus platforms to boot their secondary CPUs
- Jon Mason enables SMP on BCM4708/BCM5301X (Northstar SoCs) by building the generic
Northstar/Northstar Plus SMP code, and adding the relevant SMP Device Tree nodes
* tag 'arm-soc/for-4.5/soc' of http://github.com/Broadcom/stblinux:
ARM: BCM: Add SMP support for Broadcom 4708
ARM: BCM: Add SMP support for Broadcom NSP
ARM: BCM: Clean up SMP support for Broadcom Kona
ARM: BCM5310X: activate erratas needed for SoC
ARM: BCM5301X: remove workaround imprecise abort fault handler
Pull "Broadcom devicetree changes for v4.5¨ from Florian Fainelli:
This pull request contains the Broadcom ARM-based Device Tree changes for 4.5:
- Jon Mason enables the following for Broadcom Northstar Plus SoCs: PCI (using
iProc PCI), NAND flash controller (BRCMNAND), TWD Timer and Watchdog
(Cortex-A9), I2C (iProc), clock providers, does some Device Tree cleanups
(re-parenting, fixing register sizes and hierarchy)
- Jon Mason also adds support for some reference Broadcom Northstar reference
designs like the BCM5301X SVK reference boards, updates the existing binding
documentation to cover the Northstar chips: 4708, 4709 and 53012.
- Pramod Kumar adds the GPIO to pinctrl mapping for the Broadcom Northstar Plus
SoCs
- Yendapally Reddy Dhananjaya Reddy adds pinctrl Device Tree nodes for the
Broadcom Northstar Plus SoCs device tree nodes
- Ray Jui adds Cygnus PCIe PHY Device Tree nodes and enables MSI for the iProc
PCI controller on Cygnus platforms
- Kapil Hali adds SMP binding documentation and Device Tree nodes for the
Northstar Plus SoCs
- Florian Fainelli adds clock provider support for the Broadcom BCM63138 DSL
SoCs by utilizing the existing iProc ARM PLL controller, this includes a
stable topic branch from Stephen Boyd to be merged
- Rafal Milecki adds missing LEDs for the Netgear R8000 router
* tag 'arm-soc/for-4.5/devicetree' of http://github.com/Broadcom/stblinux:
ARM: dts: Enable MSI support for Broadcom Cygnus
ARM: dts: Add SMP support for Broadcom NSP
dt-bindings: add SMP enable-method for Broadcom NSP
ARM: dts: enable pinctrl for Broadcom NSP
ARM: dts: enable PCIe PHY support for Cygnus
ARM: dts: Cygnus: define ngpios property in gpio controller's node
ARM: BCM5301X: Add missing Netgear R8000 LEDs
ARM: dts: BCM63xx: Add ARMPLL device tree nodes
clk: bcm: Add BCM63138 clock support
clk: iproc: Extend binding to cover BCM63138
ARM: dts: enable clock support for Broadcom NSP
ARM: dts: enable clock support for BCM5301X
ARM: dts: NSP: Add I2C support to the DT
ARM: dts: NSP: Device Tree clean-ups
dts: pinctrl: Add GPIO to Pinctrl pin mapping in DT
ARM: dts: bcm5301x: Add BCM SVK DT files
dt-bindings: Add new SoCs to bcm4708 DT bindings
ARM: dts: NSP: Add TWD Support to DT
ARM: dts: NSP: Add NAND Support to DT
ARM: dts: NSP: Add PCI support
In order to meet high performance an low power requirement for Rockchip
enable the power domain support. The patch also fixes a drm/kms issue,
driver deferring untils power-domains are available)
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Though the driver will continue to check for and support the legacy
"isil,irq2-can-wakeup-machine" boolean property to wakeup source,
"wakeup-source" is the new standard binding.
This patch replaces the legacy "isil,irq2-can-wakeup-machine" with the
unified "wakeup-source" property in order to avoid any futher copy-paste
duplication.
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
-Enable USB OTG dual-role and some cleanup by make savedefconfig
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=y5U2
-----END PGP SIGNATURE-----
Merge tag 'socfpga_defconfig_for_v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/defconfig
Merge "SoCFPGA defconfig update for v4.5" from Dinh Nguyen:
-Enable USB OTG dual-role and some cleanup by make savedefconfig
* tag 'socfpga_defconfig_for_v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
arm: socfpga_defconfig: enable USB dual-role and cleanup
This adds a few features that are available on some
or all of the RealView but never made it into the SMP
defconfig file:
- Full tickless idle
- High resolution timers
- Perf events and HW perf events from the PMU
- MTD AFS partition handling
- MTD ROM partition handling
- USB and ISP1760 USB driver
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This adds a few features that are available on some
or all of the RealView but never made it into the defconfig
file:
- High-resolution timers
- Perf events and HW perf events from the PMU
- MTD AFS partition handling
- MTD ROM partition handling
- USB and ISP1760 USB driver
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This updates the RealView SMP defconfig with the latest Kconfig
structure.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This updates the RealView defconfig with the latest Kconfig
structure.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Enable the GPU for SolidRun's Cubox.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add DT support for the Vivante GC600 GPU on Marvell Dove platforms.
These nodes default to being disabled unless a platform decides they
should be enabled.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch enables some drivers for LS1021A, such as
GIANFAR, WATCHDOG, AUDIO, QSPI, I2C, ESDHC, EDMA, FTM.
QorIQ Clock Framework and Ramdisk support is also enabled.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A bunch of patches to enable new drivers related to Allwinner SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=eVFZ
-----END PGP SIGNATURE-----
Merge tag 'sunxi-defconfig-for-4.5' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/defconfig
Merge "Allwinner defconfig changes for 4.5" from Maxime Ripard:
A bunch of patches to enable new drivers related to Allwinner SoCs.
* tag 'sunxi-defconfig-for-4.5' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: sunxi: Clean up sunxi_defconfig
ARM: sunxi: Really enable LRADC keys in sunxi_defconfig
ARM: sunxi: Re-enable SID driver in sunxi_defconfig
ARM: sunxi: Re-enable SID driver in multi_v7_defconfig
ARM: multi_v7_defconfig: Enable RSB and AXP20X related drivers as modules
ARM: sunxi_defconfig: Update MFD_AXP20X symbol and enable MFD_AXP20X_RSB
update of mvebu_v5 defconfig with the addition of cpuidle
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlZlsxEACgkQCwYYjhRyO9UumgCfR353K8WoWry2InK6VnZvD9hG
tuEAnjYYkYYGvdt4/hl/ASSXTOqfM9R4
=2Sxs
-----END PGP SIGNATURE-----
Merge tag 'mvebu-defconfig-4.5-1' of git://git.infradead.org/linux-mvebu into next/defconfig
Merge "mvebu defconfig for 4.5 (part 1)" from Gregory CLEMENT:
update of mvebu_v5 defconfig with the addition of cpuidle
* tag 'mvebu-defconfig-4.5-1' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: add Kirkwood cpuidle to defconfig
ARM: mvebu: update v5 defconfig
stop using mtd->priv for NAND drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=03sV
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.5/cleanup' of git://git.infradead.org/linux-mtd into next/cleanup
Merge "MTD/NAND cleanups for v4.5" from Brian Norris:
Two changes for NAND/MTD refactoring. The mtd_to_nand() helper will allow us to
stop using mtd->priv for NAND drivers.
* tag 'arm-soc/for-4.5/cleanup' of git://git.infradead.org/linux-mtd:
ARM: nand: make use of mtd_to_nand() where appropriate
mtd: nand: add an mtd_to_nand() helper
This adds a device tree for the CloudEngines PogoPlug series 4
NAS device. Inspired by out-of-tree boardfiles from ArchLinux
by Kevin Mihelich.
Cc: Moonman <moonman.ca@gmail.com>
Cc: Kevin Mihelich <kevin@archlinuxarm.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add a new DTS file to support the Zyxel NSA325(v2) dual bay
NAS device, based on the NSA320 DTS files.
The only difference to the NSA320 device is GPIO47.
This en/disables the power for the hdd in slot2, currently
fixed to on.
[gregory.clement@free-electrons.com: fix comment format]
Signed-off-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
__user_swpX_asm maybe failed in first STREX operation, emulate_swpX
will try again, but the *data has been changed in first time. which
causes the result is wrong.
This patch is to fix this issue. When STREX succeed, change the *data.
if it fail, *data is not changed.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In cpu_v7_do_suspend routine, r11 is used while it is NOT
saved/restored, different compiler may have different usage
of ARM general registers, so it may cause issues during
calling cpu_v7_do_suspend.
We meet kernel fault occurs when using GCC 4.8.3, r11 contains
valid value before calling into cpu_v7_do_suspend, but when returned
from this routine, r11 is corrupted and lead to kernel fault.
Doing save/restore for those corrupted registers is a must in
assemble code.
Signed-off-by: Anson Huang <Anson.Huang@freescale.com>
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Cc: <stable@vger.kernel.org> # v3.3+
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The uaccess_with_memcpy() code is currently incompatible with the SW
PAN code: it takes locks within the region that we've changed the DACR,
potentially sleeping as a result. As we do not save and restore the
DACR across co-operative sleep events, can lead to an incorrect DACR
value later in this code path.
Reported-by: Peter Rosin <peda@axentia.se>
Tested-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Data have to be held longer for the PMIC device. The ACT8945A
datasheet claims that minimum SDA data hold time is about 300 ns.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
A new compatible string has been introduced: atmel,sama5d4-i2c. It
allows to use the i2c-sda-hold-time-ns property if needed.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
After the change of frequency a SAMA5D4 can reach, we have to modify the
maximum clock specification for the master clock, up to 200MHz now.
It avoids the wrong message saying that "master clk is overclocked" for this
configuration.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Enable AT91SAM9X and SAMA5D4 watchdog drivers.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add watchdog node to support SAMA5D4 watchdog.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add support for the DENX MA5D4 SoM and MA5D4EVK board. The system
consists of a SoM with eMMC, SPI NOR for booting, 2x SPI CAN chip
and an EVK with microSD slot, 2x UART, 2x CAN port, 3x USB port,
LEDs and expansion headers.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add pinmux for the 4 remaining signals used in 8-bit MMC 0
bus configuration.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Reviewed-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Synchronise the comments in mmc0 pinmux node with HSMCI0 pinmux
description in the Atmel SAMA5D4 datasheet from 24-Aug-15 page
1119, section 37.6.1, Table 37-3 .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Reviewed-by: Josh Wu <josh.wu@atmel.com>
Reported-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
WARN() takes a condition and a format string. The condition was
omitted. So I added it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The DA830 chip only works if the dcache is in writethrough mode,
but that produces a harmless Kconfig warning if the cache happens
to be disabled:
warning: (ARCH_DAVINCI_DA830) selects CPU_DCACHE_WRITETHROUGH which has unmet direct dependencies ((CPU_ARM740T || CPU_ARM920T || CPU_ARM922T || CPU_ARM925T || CPU_ARM926T || CPU_ARM940T || CPU_ARM946E || CPU_ARM1020 || CPU_FA526) && !CPU_DCACHE_DISABLE)
This makes the select conditional so we don't have to worry
about the warning in randconfig builds any more.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Update IPMMU compat strings to include SoC part number.
By specifying SoC part number in DT it becomes possible
to implement SoC specific features in the IPMMU driver.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Update IPMMU compat strings to include SoC part number.
By specifying SoC part number in DT it becomes possible
to implement SoC specific features in the IPMMU driver.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Update IPMMU compat strings to include SoC part number.
By specifying SoC part number in DT it becomes possible
to implement SoC specific features in the IPMMU driver.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Update IPMMU compat strings to include SoC part number.
By specifying SoC part number in DT it becomes possible
to implement SoC specific features in the IPMMU driver.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Gateworks Ventana boards seem to need "RGMII-ID" (internal delay)
PHY mode, instead of simple "RGMII", for their Marvell 88E1510
transceiver. Otherwise, the Ethernet MAC doesn't work with Marvell PHY
driver (TX doesn't seem to work correctly).
Tested on GW5400 rev. C.
This bug affects ARM Fedora 23.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The 'assigned-clock-parents' and 'assigned-clock-rates' list
should corresponding to the 'assigned-clocks' property clock list.
Signed-off-by: Bai Ping <b51503@freescale.com>
Fixes: ed339363de ("ARM: dts: imx6qdl-sabreauto: Allow HDMI and LVDS to work simultaneously")
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds an SMP boot method for the ARM RealView reference
designs. We also select HAVE_SMP by default and make it use
SMP_ON_UP so we only need to support one single kernel across
the RealView reference designs when using DT.
The RealViews need to have the SCU (Snoop Control Unit)
activated on boot, and this is now done by looking up its
address from the device tree and initializing it and counting
the available cores.
The RealViews boot by using a magic address register in the
system controller (SYS_FLAGS) to store the boot address,
the ROM will then read this register to the PC when the CPUs
are taken out of WFI. This code uses a handle to the syscon
regmap to access this register.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The device tree boot for RealView need the SP810 system controller
(same as found on the Versatile Express) to set up the timers on the
board so the machine can tick. It further utilize the ICST307 through
its system controller for 6 other oscillators. We have to select these
from Kconfig or the machine does not boot.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Let the platform's Kconfig to select the clock instead of having a reverse
dependency from the driver to the platform options.
Add the COMPILE_TEST option for the compilation test coverage. Due to the
non portable 'delay' code, this driver is only compilable on ARM.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Let the platform's Kconfig to select the clock instead of having a reverse
dependency from the driver to the platform options.
Add the COMPILE_TEST option for the compilation test coverage.
This change is debatable as the option itself in the Kconfig allows to
select the driver for the platform or not. This change will make the prcmu
timer always selected.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The realview barrier implementation tries to avoid calling outer_sync in order
to not lock up as a result of a bug in the l220 cache controller.
This gets in the way of the multiplatform support, but we can still remove
it if we make sure that the outer_sync function never gets called, by replacing
the function pointer with NULL, right after initialization.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[Fixed up header inclusions]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 42c4dafe80 ("ARM: 6202/1: Do not ARM_DMA_MEM_BUFFERABLE
on RealView boards with L210/L220") changed the generic setting for
ARM_DMA_MEM_BUFFERABLE to be disabled on any Realview kernel that includes
support for any of the ARM11 variations. Doing this was required to
allow doing DMA without a lockup in the l2x0 cache controller on the
Realview platform.
Unfortunately, in a kernel that also contains support for any ARMv7
based machine, the same change makes it impossible to do DMA on ARMv7,
which gets in the way of enabling multiplatform support on Realview.
As confirmed by Catalin Marinas and Linus Walleij, the current
code for Realview that we have in the kernel does not actually
perform any DMA, and this is unlikely to change in the future.
Therefore we can revert 42c4dafe80 without introducing regressions,
but we must never start using DMA on this platform in the future.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
PCI support for realview was never merged, and trying to build realview with
CONFIG_PCI enabled fails because the constants for the mapping windows are
not defined anywhere.
This removes them from the static I/O window mapping table as a preparation
for multiplatform support.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The realview-pbx platform has an elaborate way of avoiding the use of highmem
by redefining its phys_to_virt function. In practice this doesn't help all
that much, and it gets in the way of doing multiplatform builds for
realview.
This removes the feature and kills off the mach/memory.h file for realview.
We also lose the ability to do sparsemem with this patch, but that should
be put back into place for generic multiplatform configurations, to save
a little memory on PBX.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of having the clocksource's Kconfig depending on the arch, let the
arch to select the timer it needs.
The CLKSRC_OF dependency is removed because already selected by the
ARCH_PXA, and it is added for SA1100.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Change the Kconfig selection rule by letting the STI arch to select
the timer.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Two patches, one to fix the touchscreen axis on one Allwinner board, and
the other one fixing a mutex unlocking issue on one error path in the RSB
driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9lSI
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.4' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Merge "Allwinner fixes for 4.4" from Maxime Ripard:
Allwinner fixes for 4.4
Two patches, one to fix the touchscreen axis on one Allwinner board, and
the other one fixing a mutex unlocking issue on one error path in the RSB
driver.
* tag 'sunxi-fixes-for-4.4' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
bus: sunxi-rsb: unlock on error in sunxi_rsb_read()
ARM: dts: sunxi: sun6i-a31s-primo81.dts: add touchscreen axis swapping property
Add I2C0 and two I2C EEPROM devices on the CIAA-NXP board:
* 24AA1025 EEPROM, 1Mbit: it is accessed as two 512Kbit EEPROMs.
* 24AA025E48 EEPROM, 2kbit.
Signed-off-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
