Add hardware timestamps to management frame RX info.
This shall be used by drivers that support hardware timestamping for
Timing measurement and Fine timing measurement action frames RX.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The functions for reporting rx management take many arguments.
Collect all the arguments into a struct, which also make it easier
to add more arguments if needed.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a function for reporting TX status with hardware timestamps. This
function shall be used for reporting the TX status of Timing
measurement and Fine timing measurement action frames by devices that
support reporting hardware timestamps.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When inserting a link STA, make sure it doesn't exist first
and add lockdep assertions that we cannot modify the hash
table without holding the sta_mtx, so this check is really
correct.
Also return without hashing if the driver failed, and warn
if the hashing fails, which shouldn't happen due to the
check described above.
Fixes: cb71f1d136 ("wifi: mac80211: add sta link addition/removal")
Fixes: ba6ddab94f ("wifi: mac80211: maintain link-sta hash table")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We need to copy the address to both the private and public
portion of the link_sta (the private one is needed for the
hash table). Fix this.
Fixes: bbe90107e1 ("wifi: mac80211: mlme: refactor link station setup")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Clarify the link ID behaviour in control port TX, we need it
to select the link to transmit on for both MLD and non-MLD
receivers, but select the link address as the SA only if the
receiver is not an MLD.
Fixes: 67207bab93 ("wifi: cfg80211/mac80211: Support control port TX from specific link")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the frame is going to be dropped anyway because
ieee80211_lookup_ra_sta() returned an error (and
even though it's a bit racy, it will likely continue
to do so), return the error out instead of just
silently dropping the frame.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We always need the MLD address and link ID to add or
modify the link STA, so require it in the API.
Fixes: 577e5b8c39 ("wifi: cfg80211: add API to add/modify/remove a link station")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add more sanity checks to the API handling, we shouldn't
be able to create a station without links, nor should we
be able to add a link to a station that wasn't created as
an MLD with links in the first place.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are two issues here: we unhash the link stations only
directly before freeing the station they belong to, and we
also don't unhash all the links correctly in all cases. Fix
these issues.
Fixes: ba6ddab94f ("wifi: mac80211: maintain link-sta hash table")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When modifying a link station, validate that the link address
doesn't change, except the first time the link is created.
Fixes: b95eb7f0ee ("wifi: cfg80211/mac80211: separate link params from station params")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
At this point, we've already changed link_id to be zero for
a non-MLO connection, so use the 'mlo' variable rather than
link ID to determine the MLO status of the station.
Fixes: bd363ee533 ("wifi: mac80211: mlme: set sta.mlo correctly")
Fixes: 81151ce462 ("wifi: mac80211: support MLO authentication/association with one link")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If there's a non-MLO client, the A2 must be set to the BSSID
of the link since no translation will happen in lower layers
and it's needed that way for encryption.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We should only translate addr3 here if it's the BSSID.
Fixes: 42fb9148c0 ("wifi: mac80211: do link->MLD address translation on RX")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we have a non-MLD STA on an AP MLD, we crash while
adding the station. Fix that, in this case we need to
use the STA's address also on the link data structure.
Fixes: f36fe0a2df ("wifi: mac80211: fix up link station creation/insertion")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In my previous changes here, I neglected to take the old
conn_flags into account that might still be present from
the authentication, and thus ieee80211_setup_assoc_link()
can misbehave, as well as the override calculation being
wrong. Fix that by ORing in the old flags.
Fixes: 1845c1d4a4 ("wifi: mac80211: mlme: refactor assoc link setup")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In a few places we need to use the AP (MLD) address, not the
deflink BSSID, the link address translation will happen later.
To make that work properly for fast-xmit, set up the ap_addr
in the vif.cfg earlier.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Bitmap are "unsigned long", so use it instead of a "u32" to make things
more explicit.
While at it, remove some useless cast (and leading spaces) when using the
bitmap API.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ping sockets don't appear to make any attempt to preserve flow labels
created and set by userspace using IPV6_FLOWINFO_SEND. Instead they are
clobbered by autolabels (if enabled) or zero.
Grab the flowlabel out of the msghdr similar to how rawv6_sendmsg does
it and move the memset up so it doesn't get zeroed after.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_invalid_ratelimit, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its reader.
Fixes: 032ee42369 ("tcp: helpers to mitigate ACK loops by rate-limiting out-of-window dupacks")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_autocorking, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: f54b311142 ("tcp: auto corking")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_min_rtt_wlen, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: f672258391 ("tcp: track min RTT using windowed min-filter")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_tso_rtt_log, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 65466904b0 ("tcp: adjust TSO packet sizes based on min_rtt")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_min_tso_segs, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 95bd09eb27 ("tcp: TSO packets automatic sizing")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_challenge_ack_limit, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its reader.
Fixes: 282f23c6ee ("tcp: implement RFC 5961 3.2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_limit_output_bytes, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its reader.
Fixes: 46d3ceabd8 ("tcp: TCP Small Queues")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_workaround_signed_windows, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its readers.
Fixes: 15d99e02ba ("[TCP]: sysctl to allow TCP window > 32767 sans wscale")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_moderate_rcvbuf, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its readers.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_no_ssthresh_metrics_save, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its readers.
Fixes: 65e6d90168 ("net-tcp: Disable TCP ssthresh metrics cache by default")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_nometrics_save, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_frto, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_app_win, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_dsack, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce bpf_ct_set_status and bpf_ct_change_status kfunc helpers in
order to set nf_conn field of allocated entry or update nf_conn status
field of existing inserted entry. Use nf_ct_change_status_common to
share the permitted status field changes between netlink and BPF side
by refactoring ctnetlink_change_status.
It is required to introduce two kfuncs taking nf_conn___init and nf_conn
instead of sharing one because KF_TRUSTED_ARGS flag causes strict type
checking. This would disallow passing nf_conn___init to kfunc taking
nf_conn, and vice versa. We cannot remove the KF_TRUSTED_ARGS flag as we
only want to accept refcounted pointers and not e.g. ct->master.
Hence, bpf_ct_set_* kfuncs are meant to be used on allocated CT, and
bpf_ct_change_* kfuncs are meant to be used on inserted or looked up
CT entry.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Co-developed-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Link: https://lore.kernel.org/r/20220721134245.2450-10-memxor@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Introduce bpf_ct_set_timeout and bpf_ct_change_timeout kfunc helpers in
order to change nf_conn timeout. This is same as ctnetlink_change_timeout,
hence code is shared between both by extracting it out to
__nf_ct_change_timeout. It is also updated to return an error when it
sees IPS_FIXED_TIMEOUT_BIT bit in ct->status, as that check was missing.
It is required to introduce two kfuncs taking nf_conn___init and nf_conn
instead of sharing one because KF_TRUSTED_ARGS flag causes strict type
checking. This would disallow passing nf_conn___init to kfunc taking
nf_conn, and vice versa. We cannot remove the KF_TRUSTED_ARGS flag as we
only want to accept refcounted pointers and not e.g. ct->master.
Apart from this, bpf_ct_set_timeout is only called for newly allocated
CT so it doesn't need to inspect the status field just yet. Sharing the
helpers even if it was possible would make timeout setting helper
sensitive to order of setting status and timeout after allocation.
Hence, bpf_ct_set_* kfuncs are meant to be used on allocated CT, and
bpf_ct_change_* kfuncs are meant to be used on inserted or looked up
CT entry.
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Link: https://lore.kernel.org/r/20220721134245.2450-9-memxor@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Introduce bpf_xdp_ct_alloc, bpf_skb_ct_alloc and bpf_ct_insert_entry
kfuncs in order to insert a new entry from XDP and TC programs.
Introduce bpf_nf_ct_tuple_parse utility routine to consolidate common
code.
We extract out a helper __nf_ct_set_timeout, used by the ctnetlink and
nf_conntrack_bpf code, extract it out to nf_conntrack_core, so that
nf_conntrack_bpf doesn't need a dependency on CONFIG_NF_CT_NETLINK.
Later this helper will be reused as a helper to set timeout of allocated
but not yet inserted CT entry.
The allocation functions return struct nf_conn___init instead of
nf_conn, to distinguish allocated CT from an already inserted or looked
up CT. This is later used to enforce restrictions on what kfuncs
allocated CT can be used with.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Co-developed-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Link: https://lore.kernel.org/r/20220721134245.2450-8-memxor@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Move common checks inside the common function, and maintain the only
difference the two being how to obtain the struct net * from ctx.
No functional change intended.
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Link: https://lore.kernel.org/r/20220721134245.2450-7-memxor@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Teach the verifier to detect a new KF_TRUSTED_ARGS kfunc flag, which
means each pointer argument must be trusted, which we define as a
pointer that is referenced (has non-zero ref_obj_id) and also needs to
have its offset unchanged, similar to how release functions expect their
argument. This allows a kfunc to receive pointer arguments unchanged
from the result of the acquire kfunc.
This is required to ensure that kfunc that operate on some object only
work on acquired pointers and not normal PTR_TO_BTF_ID with same type
which can be obtained by pointer walking. The restrictions applied to
release arguments also apply to trusted arguments. This implies that
strict type matching (not deducing type by recursively following members
at offset) and OBJ_RELEASE offset checks (ensuring they are zero) are
used for trusted pointer arguments.
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Link: https://lore.kernel.org/r/20220721134245.2450-5-memxor@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Instead of populating multiple sets to indicate some attribute and then
researching the same BTF ID in them, prepare a single unified BTF set
which indicates whether a kfunc is allowed to be called, and also its
attributes if any at the same time. Now, only one call is needed to
perform the lookup for both kfunc availability and its attributes.
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Link: https://lore.kernel.org/r/20220721134245.2450-4-memxor@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The accept_untracked_na sysctl changed from a boolean to an integer
when a new knob '2' was added. This patch provides a safeguard to avoid
accepting values that are not defined in the sysctl. When setting a
value greater than 2, the user will get an 'invalid argument' warning.
Fixes: aaa5f515b1 ("net: ipv6: new accept_untracked_na option to accept na only if in-network")
Signed-off-by: Jaehee Park <jhpark1013@gmail.com>
Suggested-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Suggested-by: Roopa Prabhu <roopa@nvidia.com>
Reviewed-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Link: https://lore.kernel.org/r/20220720183632.376138-1-jhpark1013@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric reports we should release the socket lock if the entire
"grab reader lock" operation has failed. The callers assume
they don't have to release it or otherwise unwind.
Reported-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot+16e72110feb2b653ef27@syzkaller.appspotmail.com
Fixes: 4cbc325ed6 ("tls: rx: allow only one reader at a time")
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20220720203701.2179034-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If a command cannot be sent or there is a internal error an errno maybe
set instead of a command status.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This splits hci_dev_open_sync so each stage is handle by its own
function so it is easier to identify each stage.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Make use of hci_cmd_sync_queue for removing an advertisement monitor.
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Reviewed-by: Miao-chen Chou <mcchou@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Make use of hci_cmd_sync_queue for adding an advertisement monitor.
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Reviewed-by: Miao-chen Chou <mcchou@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Core driver addtionally checks LMP feature bit "Erroneous Data Reporting"
instead of quirk HCI_QUIRK_BROKEN_ERR_DATA_REPORTING to decide if HCI
commands HCI_Read|Write_Default_Erroneous_Data_Reporting are broken, so
remove this unnecessary quirk.
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Tested-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
BT core driver should addtionally check LMP feature bit
"Erroneous Data Reporting" instead of quirk
HCI_QUIRK_BROKEN_ERR_DATA_REPORTING set by BT device driver to decide if
HCI commands HCI_Read|Write_Default_Erroneous_Data_Reporting are broken.
BLUETOOTH CORE SPECIFICATION Version 5.3 | Vol 2, Part C | page 587
This feature indicates whether the device is able to support the
Packet_Status_Flag and the HCI commands HCI_Write_Default_-
Erroneous_Data_Reporting and HCI_Read_Default_Erroneous_-
Data_Reporting.
the quirk was introduced by 'commit cde1a8a992 ("Bluetooth: btusb: Fix
and detect most of the Chinese Bluetooth controllers")' to mark HCI
commands HCI_Read|Write_Default_Erroneous_Data_Reporting broken by BT
device driver, but the reason why these two HCI commands are broken is
that feature "Erroneous Data Reporting" is not enabled by firmware, this
scenario is illustrated by below log of QCA controllers with USB I/F:
@ RAW Open: hcitool (privileged) version 2.22
< HCI Command: Read Local Supported Commands (0x04|0x0002) plen 0
> HCI Event: Command Complete (0x0e) plen 68
Read Local Supported Commands (0x04|0x0002) ncmd 1
Status: Success (0x00)
Commands: 288 entries
......
Read Default Erroneous Data Reporting (Octet 18 - Bit 2)
Write Default Erroneous Data Reporting (Octet 18 - Bit 3)
......
< HCI Command: Read Default Erroneous Data Reporting (0x03|0x005a) plen 0
> HCI Event: Command Complete (0x0e) plen 4
Read Default Erroneous Data Reporting (0x03|0x005a) ncmd 1
Status: Unknown HCI Command (0x01)
< HCI Command: Read Local Supported Features (0x04|0x0003) plen 0
> HCI Event: Command Complete (0x0e) plen 12
Read Local Supported Features (0x04|0x0003) ncmd 1
Status: Success (0x00)
Features: 0xff 0xfe 0x0f 0xfe 0xd8 0x3f 0x5b 0x87
3 slot packets
......
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Tested-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Event HCI_Truncated_Page_Complete should belong to central
and HCI_Peripheral_Page_Response_Timeout should belong to
peripheral, but hci_set_event_mask_page_2_sync() take these
two events for wrong roles, so correct it by this change.
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
These devices are likely going to be reprogrammed when disconnected so
this avoid a whole bunch of commands attempt to remove and the add back
to the list.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Zhengping Jiang <jiangzp@google.com>
When programming a new entry into the resolving list it shall default
to network mode since the params may contain the mode programmed when
the device was last added to the resolving list.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209745
Fixes: 853b70b506 ("Bluetooth: hci_sync: Set Privacy Mode when updating the resolving list")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Zhengping Jiang <jiangzp@google.com>
Annotate hci_rx_work() with kcov_remote_start() and kcov_remote_stop()
calls, so remote KCOV coverage is collected while processing the rx_q
queue which is the main incoming Bluetooth packet queue.
Coverage is associated with the thread which created the packet skb.
The collected extra coverage helps kernel fuzzing efforts in finding
vulnerabilities.
This change only has effect if the kernel is compiled with CONFIG_KCOV,
otherwise kcov_ functions don't do anything.
Signed-off-by: Tamas Koczka <poprdi@google.com>
Tested-by: Aleksandr Nogikh <nogikh@google.com>
Reviewed-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
After resuming, remove setting scanning_paused to false, because it is
checked and set to false in hci_resume_scan_sync. Also move setting
the value to false before updating passive scan, because the value is
used when resuming passive scan.
Fixes: 3b42055388 (Bluetooth: hci_sync: Fix attempting to suspend with
unfiltered passive scan)
Signed-off-by: Zhengping Jiang <jiangzp@google.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Set the connection data before calling get_conn_info_sync, so it can be
verified the connection is still connected, before refreshing cached
values.
Fixes: 47db6b4299 ("Bluetooth: hci_sync: Convert MGMT_OP_GET_CONN_INFO")
Signed-off-by: Zhengping Jiang <jiangzp@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The scan response and advertising data needs to be tracked on a per
instance (adv_info) since when these instaces are removed so are their
data, to fix that new flags are introduced which is used to mark when
the data changes and then checked to confirm when the data needs to be
synced with the controller.
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Both dev_name and short_name are not guaranteed to be NULL terminated so
this instead use strnlen and then attempt to determine if the resulting
string needs to be truncated or not.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216018
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Similar to the handling of l2cap_ecred_connect in commit d3715b2333
("Bluetooth: use memset avoid memory leaks"), we thought a patch
might be needed here as well.
Use memset to initialize structs to prevent memory leaks
in l2cap_le_connect
Signed-off-by: Xiaohui Zhang <xiaohuizhang@ruc.edu.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When HCI_USERCHANNEL is used, unregister the suspend notifier when
binding and register when releasing. The userchannel socket should be
left alone after open is completed.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When a userchannel socket is released, we should check whether the hdev
is already unregistered before sending out an IndexAdded.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If a hardware error occurs and the connections are flushed without a
disconnection_complete event being signaled, the temporary linkkeys are
not flushed.
This change ensures that any outstanding flushable linkkeys are flushed
when the connection are flushed from the hash table.
Additionally, this also makes use of test_and_clear_bit to avoid
multiple attempts to delete the link key that's already been flushed.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for net-next:
1) Simplify nf_ct_get_tuple(), from Jackie Liu.
2) Add format to request_module() call, from Bill Wendling.
3) Add /proc/net/stats/nf_flowtable to monitor in-flight pending
hardware offload objects to be processed, from Vlad Buslov.
4) Missing rcu annotation and accessors in the netfilter tree,
from Florian Westphal.
5) Merge h323 conntrack helper nat hooks into single object,
also from Florian.
6) A batch of update to fix sparse warnings treewide,
from Florian Westphal.
7) Move nft_cmp_fast_mask() where it used, from Florian.
8) Missing const in nf_nat_initialized(), from James Yonan.
9) Use bitmap API for Maglev IPVS scheduler, from Christophe Jaillet.
10) Use refcount_inc instead of _inc_not_zero in flowtable,
from Florian Westphal.
11) Remove pr_debug in xt_TPROXY, from Nathan Cancellor.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next:
netfilter: xt_TPROXY: remove pr_debug invocations
netfilter: flowtable: prefer refcount_inc
netfilter: ipvs: Use the bitmap API to allocate bitmaps
netfilter: nf_nat: in nf_nat_initialized(), use const struct nf_conn *
netfilter: nf_tables: move nft_cmp_fast_mask to where its used
netfilter: nf_tables: use correct integer types
netfilter: nf_tables: add and use BE register load-store helpers
netfilter: nf_tables: use the correct get/put helpers
netfilter: x_tables: use correct integer types
netfilter: nfnetlink: add missing __be16 cast
netfilter: nft_set_bitmap: Fix spelling mistake
netfilter: h323: merge nat hook pointers into one
netfilter: nf_conntrack: use rcu accessors where needed
netfilter: nf_conntrack: add missing __rcu annotations
netfilter: nf_flow_table: count pending offload workqueue tasks
net/sched: act_ct: set 'net' pointer when creating new nf_flow_table
netfilter: conntrack: use correct format characters
netfilter: conntrack: use fallthrough to cleanup
====================
Link: https://lore.kernel.org/r/20220720230754.209053-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
pr_debug calls are no longer needed in this file.
Pablo suggested "a patch to remove these pr_debug calls". This patch has
some other beneficial collateral as it also silences multiple Clang
-Wformat warnings that were present in the pr_debug calls.
diff from v1 -> v2:
* converted if statement one-liner style
* x == NULL is now !x
Suggested-by: Pablo Neira Ayuso <pablo@netfilter.org>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Justin Stitt <justinstitt@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
With refcount_inc_not_zero, we'd also need a smp_rmb or similar,
followed by a test of the CONFIRMED bit.
However, the ct pointer is taken from skb->_nfct, its refcount must
not be 0 (else, we'd already have a use-after-free bug).
Use refcount_inc() instead to clarify the ct refcount is expected to
be at least 1.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Use bitmap_zalloc()/bitmap_free() instead of hand-writing them.
It is less verbose and it improves the semantic.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The cited commit refactored the flow action initialization sequence to
use an interface method when translating tc action instances to flow
offload objects. The refactored version skips the initialization of the
generic flow action attributes for tc actions, such as pedit, that allocate
more than one offload entry. This can cause potential issues for drivers
mapping flow action ids.
Populate the generic flow action fields for all the flow action entries.
Fixes: c54e1d920f ("flow_offload: add ops to tc_action_ops for flow action setup")
Signed-off-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
----
v1 -> v2:
- coalese the generic flow action fields initialization to a single loop
Reviewed-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_max_reordering, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its readers.
Fixes: dca145ffaa ("tcp: allow for bigger reordering level")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_abort_on_overflow, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_rfc1337, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_stdurg, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_retrans_collapse, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its reader.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_slow_start_after_idle, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its readers.
Fixes: 35089bb203 ("[TCP]: Add tcp_slow_start_after_idle sysctl.")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_thin_linear_timeouts, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its reader.
Fixes: 36e31b0af5 ("net: TCP thin linear timeouts")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_recovery, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
Fixes: 4f41b1c58a ("tcp: use RACK to detect losses")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_early_retrans, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: eed530b6c6 ("tcp: early retransmit")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading these knobs, they can be changed concurrently.
Thus, we need to add READ_ONCE() to their readers.
- tcp_sack
- tcp_window_scaling
- tcp_timestamps
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sysctl_ip_prot_sock is accessed concurrently, and there is always a chance
of data-race. So, all readers and writers need some basic protection to
avoid load/store-tearing.
Fixes: 4548b683b7 ("Introduce a sysctl that modifies the value of PROT_SOCK.")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_fib_multipath_hash_fields, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its readers.
Fixes: ce5c9c20d3 ("ipv4: Add a sysctl to control multipath hash fields")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_fib_multipath_hash_policy, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its readers.
Fixes: bf4e0a3db9 ("net: ipv4: add support for ECMP hash policy choice")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_fib_multipath_use_neigh, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its reader.
Fixes: a6db4494d2 ("net: ipv4: Consider failed nexthops in multipath routes")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2022-07-20
1) Fix a policy refcount imbalance in xfrm_bundle_lookup.
From Hangyu Hua.
2) Fix some clang -Wformat warnings.
Justin Stitt
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Begunkov says:
====================
io_uring zerocopy send
The patchset implements io_uring zerocopy send. It works with both registered
and normal buffers, mixing is allowed but not recommended. Apart from usual
request completions, just as with MSG_ZEROCOPY, io_uring separately notifies
the userspace when buffers are freed and can be reused (see API design below),
which is delivered into io_uring's Completion Queue. Those "buffer-free"
notifications are not necessarily per request, but the userspace has control
over it and should explicitly attaching a number of requests to a single
notification. The series also adds some internal optimisations when used with
registered buffers like removing page referencing.
From the kernel networking perspective there are two main changes. The first
one is passing ubuf_info into the network layer from io_uring (inside of an
in kernel struct msghdr). This allows extra optimisations, e.g. ubuf_info
caching on the io_uring side, but also helps to avoid cross-referencing
and synchronisation problems. The second part is an optional optimisation
removing page referencing for requests with registered buffers.
Benchmarking UDP with an optimised version of the selftest (see [1]), which
sends a bunch of requests, waits for completions and repeats. "+ flush" column
posts one additional "buffer-free" notification per request, and just "zc"
doesn't post buffer notifications at all.
NIC (requests / second):
IO size | non-zc | zc | zc + flush
4000 | 495134 | 606420 (+22%) | 558971 (+12%)
1500 | 551808 | 577116 (+4.5%) | 565803 (+2.5%)
1000 | 584677 | 592088 (+1.2%) | 560885 (-4%)
600 | 596292 | 598550 (+0.4%) | 555366 (-6.7%)
dummy (requests / second):
IO size | non-zc | zc | zc + flush
8000 | 1299916 | 2396600 (+84%) | 2224219 (+71%)
4000 | 1869230 | 2344146 (+25%) | 2170069 (+16%)
1200 | 2071617 | 2361960 (+14%) | 2203052 (+6%)
600 | 2106794 | 2381527 (+13%) | 2195295 (+4%)
Previously it also brought a massive performance speedup compared to the
msg_zerocopy tool (see [3]), which is probably not super interesting. There
is also an additional bunch of refcounting optimisations that was omitted from
the series for simplicity and as they don't change the picture drastically,
they will be sent as follow up, as well as flushing optimisations closing the
performance gap b/w two last columns.
For TCP on localhost (with hacks enabling localhost zerocopy) and including
additional overhead for receive:
IO size | non-zc | zc
1200 | 4174 | 4148
4096 | 7597 | 11228
Using a real NIC 1200 bytes, zc is worse than non-zc ~5-10%, maybe the
omitted optimisations will somewhat help, should look better for 4000,
but couldn't test properly because of setup problems.
Links:
liburing (benchmark + tests):
[1] https://github.com/isilence/liburing/tree/zc_v4
kernel repo:
[2] https://github.com/isilence/linux/tree/zc_v4
RFC v1:
[3] https://lore.kernel.org/io-uring/cover.1638282789.git.asml.silence@gmail.com/
RFC v2:
https://lore.kernel.org/io-uring/cover.1640029579.git.asml.silence@gmail.com/
Net patches based:
git@github.com:isilence/linux.git zc_v4-net-base
or
https://github.com/isilence/linux/tree/zc_v4-net-base
API design overview:
The series introduces an io_uring concept of notifactors. From the userspace
perspective it's an entity to which it can bind one or more requests and then
requesting to flush it. Flushing a notifier makes it impossible to attach new
requests to it, and instructs the notifier to post a completion once all
requests attached to it are completed and the kernel doesn't need the buffers
anymore.
Notifications are stored in notification slots, which should be registered as
an array in io_uring. Each slot stores only one notifier at any particular
moment. Flushing removes it from the slot and the slot automatically replaces
it with a new notifier. All operations with notifiers are done by specifying
an index of a slot it's currently in.
When registering a notification the userspace specifies a u64 tag for each
slot, which will be copied in notification completion entries as
cqe::user_data. cqe::res is 0 and cqe::flags is equal to wrap around u32
sequence number counting notifiers of a slot.
====================
Link: https://lore.kernel.org/r/cover.1657643355.git.asml.silence@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Teach tcp how to use external ubuf_info provided in msghdr and
also prepare it for managed frags by sprinkling
skb_zcopy_downgrade_managed() when it could mix managed and not managed
frags.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Teach ipv6/udp how to use external ubuf_info provided in msghdr and
also prepare it for managed frags by sprinkling
skb_zcopy_downgrade_managed() when it could mix managed and not managed
frags.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Teach ipv4/udp how to use external ubuf_info provided in msghdr and
also prepare it for managed frags by sprinkling
skb_zcopy_downgrade_managed() when it could mix managed and not managed
frags.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some users like io_uring can do page pinning more efficiently, so we
want a way to delegate referencing to other subsystems. For that add
a new flag called SKBFL_MANAGED_FRAG_REFS. When set, skb doesn't hold
page references and upper layers are responsivle to managing page
lifetime.
It's allowed to convert skbs from managed to normal by calling
skb_zcopy_downgrade_managed(). The function will take all needed
page references and clear the flag. It's needed, for instance,
to avoid mixing managed modes.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for custom iov_iter handling to msghdr. The idea is that
in-kernel subsystems want control over how an SG is split.
Signed-off-by: David Ahern <dsahern@kernel.org>
[pavel: move callback into msghdr]
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make possible for network in-kernel callers like io_uring to pass in a
custom ubuf_info by setting it in a new field of struct msghdr.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The "ds" iterator variable used in dsa_port_reset_vlan_filtering() ->
dsa_switch_for_each_port() overwrites the "dp" received as argument,
which is later used to call dsa_port_vlan_filtering() proper.
As a result, switches which do enter that code path (the ones with
vlan_filtering_is_global=true) will dereference an invalid dp in
dsa_port_reset_vlan_filtering() after leaving a VLAN-aware bridge.
Use a dedicated "other_dp" iterator variable to avoid this from
happening.
Fixes: d0004a020b ("net: dsa: remove the "dsa_to_port in a loop" antipattern from the core")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The blamed refactoring commit changed a "port" iterator with "other_dp",
but still looked at the slave_dev of the dp outside the loop, instead of
other_dp->slave from the loop.
As a result, dsa_port_vlan_filtering() would not call
dsa_slave_manage_vlan_filtering() except for the port in cause, and not
for all switch ports as expected.
Fixes: d0004a020b ("net: dsa: remove the "dsa_to_port in a loop" antipattern from the core")
Reported-by: Lucian Banu <Lucian.Banu@westermo.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove locked versions of functions that are no longer used by anyone.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Prepare for devlink reload being called with devlink->lock held and
convert the netdevsim driver to use unlocked devlink API during init and
fini flows. Take devl_lock() in reload_down() and reload_up() ops in the
meantime before reload cmd is converted to take the lock itself.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add unlocked variants of devlink_region_create/destroy() functions
to be used in drivers called-in with devlink->lock held.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add unlocked variants of devlink_dpipe*() functions to be used
in drivers called-in with devlink->lock held.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add unlocked variants of devlink_sb*() functions to be used
in drivers called-in with devlink->lock held.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add unlocked variants of devlink_resource*() functions to be used
in drivers called-in with devlink->lock held.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add unlocked variants of devl_trap*() functions to be used in drivers
called-in with devlink->lock held.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We don't want to list every single ubuf_info callback in
skb_orphan_frags(), add a flag controlling the behaviour.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We should not append MSG_ZEROCOPY requests to skbuff with non
MSG_ZEROCOPY ubuf_info, they might be not compatible.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Even when zerocopy transmission is requested and possible,
__ip_append_data() will still copy a small chunk of data just because it
allocated some extra linear space (e.g. 128 bytes). It wastes CPU cycles
on copy and iter manipulations and also misalignes potentially aligned
data. Avoid such copies. And as a bonus we can allocate smaller skb.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Even when zerocopy transmission is requested and possible,
__ip_append_data() will still copy a small chunk of data just because it
allocated some extra linear space (e.g. 148 bytes). It wastes CPU cycles
on copy and iter manipulations and also misalignes potentially aligned
data. Avoid such copies. And as a bonus we can allocate smaller skb.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
lockdep complains use of uninitialized spinlock at ieee80211_do_stop() [1],
for commit f856373e2f ("wifi: mac80211: do not wake queues on a vif
that is being stopped") guards clear_bit() using fq.lock even before
fq_init() from ieee80211_txq_setup_flows() initializes this spinlock.
According to discussion [2], Toke was not happy with expanding usage of
fq.lock. Since __ieee80211_wake_txqs() is called under RCU read lock, we
can instead use synchronize_rcu() for flushing ieee80211_wake_txqs().
Link: https://syzkaller.appspot.com/bug?extid=eceab52db7c4b961e9d6 [1]
Link: https://lkml.kernel.org/r/874k0zowh2.fsf@toke.dk [2]
Reported-by: syzbot <syzbot+eceab52db7c4b961e9d6@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Fixes: f856373e2f ("wifi: mac80211: do not wake queues on a vif that is being stopped")
Tested-by: syzbot <syzbot+eceab52db7c4b961e9d6@syzkaller.appspotmail.com>
Acked-by: Toke Høiland-Jørgensen <toke@kernel.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/9cc9b81d-75a3-3925-b612-9d0ad3cab82b@I-love.SAKURA.ne.jp
While reading sysctl_tcp_fastopen_blackhole_timeout, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its readers.
Fixes: cf1ef3f071 ("net/tcp_fastopen: Disable active side TFO in certain scenarios")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_fastopen, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
Fixes: 2100c8d2d9 ("net-tcp: Fast Open base")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_max_syn_backlog, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_tw_reuse, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading these sysctl knobs, they can be changed concurrently.
Thus, we need to add READ_ONCE() to their readers.
- tcp_retries1
- tcp_retries2
- tcp_orphan_retries
- tcp_fin_timeout
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_reordering, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_migrate_req, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
Fixes: f9ac779f88 ("net: Introduce net.ipv4.tcp_migrate_req.")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_syncookies, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_syn(ack)?_retries, they can be changed
concurrently. Thus, we need to add READ_ONCE() to their readers.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_keepalive_(time|probes|intvl), they can be changed
concurrently. Thus, we need to add READ_ONCE() to their readers.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_igmp_qrv, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
This test can be packed into a helper, so such changes will be in the
follow-up series after net is merged into net-next.
qrv ?: READ_ONCE(net->ipv4.sysctl_igmp_qrv);
Fixes: a9fe8e2994 ("ipv4: implement igmp_qrv sysctl to tune igmp robustness variable")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_igmp_max_msf, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_igmp_max_memberships, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_igmp_llm_reports, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
This test can be packed into a helper, so such changes will be in the
follow-up series after net is merged into net-next.
if (ipv4_is_local_multicast(pmc->multiaddr) &&
!READ_ONCE(net->ipv4.sysctl_igmp_llm_reports))
Fixes: df2cf4a78e ("IGMP: Inhibit reports for local multicast groups")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Socket destruction flow and tls_device_down function sync against each
other using tls_device_lock and the context refcount, to guarantee the
device resources are freed via tls_dev_del() by the end of
tls_device_down.
In the following unfortunate flow, this won't happen:
- refcount is decreased to zero in tls_device_sk_destruct.
- tls_device_down starts, skips the context as refcount is zero, going
all the way until it flushes the gc work, and returns without freeing
the device resources.
- only then, tls_device_queue_ctx_destruction is called, queues the gc
work and frees the context's device resources.
Solve it by decreasing the refcount in the socket's destruction flow
under the tls_device_lock, for perfect synchronization. This does not
slow down the common likely destructor flow, in which both the refcount
is decreased and the spinlock is acquired, anyway.
Fixes: e8f6979981 ("net/tls: Add generic NIC offload infrastructure")
Reviewed-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently CoW Rx skbs whenever we can't decrypt to a user
space buffer. The skbs can be enormous (64kB) and CoW does
a linear alloc which has a strong chance of failing under
memory pressure. Or even without, skb_cow_data() assumes
GFP_ATOMIC.
Allocate a new frag'd skb and decrypt into it. We finally
take advantage of the decrypted skb getting returned via
darg.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "zero-copy" path in SW TLS will engage either for no skbs or
for all but last. If the recvmsg parameters are right and the
socket can do ZC we'll ZC until the iterator can't fit a full
record at which point we'll decrypt one more record and copy
over the necessary bits to fill up the request.
The only reason we hold onto the ZC skbs which went thru the async
path until the end of recvmsg() is to count bytes. We need an accurate
count of zc'ed bytes so that we can calculate how much of the non-zc'd
data to copy. To allow freeing input skbs on the ZC path count only
how much of the list we'll need to consume.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Async crypto currently benefits from the fact that we decrypt
in place. When we allow input and output to be different skbs
we will have to hang onto the input while we move to the next
record. Clone the inputs and keep them on a list.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Async crypto TLS Rx currently waits for crypto to be done
in order to strip the TLS header and tailer. Simplify
the code by moving the pointers immediately, since only
TLS 1.2 is supported here there is no message padding.
This simplifies the decryption into a new skb in the next
patch as we don't have to worry about input vs output
skb in the decrypt_done() handler any more.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using ctx->recv_pkt after decryption read the skb
from darg.skb. This moves the decision of what the "output skb"
is to the decrypt handlers. For now after decrypt handler returns
successfully ctx->recv_pkt is simply moved to darg.skb, but it
will change soon.
Note that tls_decrypt_sg() cannot clear the ctx->recv_pkt
because it gets called to re-encrypt (i.e. by the device offload).
So we need an awkward temporary if() in tls_rx_one_record().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Callers always pass ctx->recv_pkt into decrypt_skb_update(),
and it propagates it to its callees. This may give someone
the false impression that those functions can accept any valid
skb containing a TLS record. That's not the case, the record
sequence number is read from the context, and they can only
take the next record coming out of the strp.
Let the functions get the skb from the context instead of
passing it in. This will also make it cleaner to return
a different skb than ctx->recv_pkt as the decrypted one
later on.
Since we're touching the definition of decrypt_skb_update()
use this as an opportunity to rename it.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I already forgot to transform darg from input to output
semantics once on the NIC inline crypto fastpath. To
avoid this happening again create a device equivalent
of decrypt_internal(). A function responsible for decryption
and transforming darg.
While at it rename decrypt_internal() to a hopefully slightly
more meaningful name.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We no longer allow a decrypted skb to remain linked to ctx->recv_pkt.
Anything on the list is decrypted, anything on ctx->recv_pkt needs
to be decrypted.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Detach the skb from ctx->recv_pkt after decryption is done,
even if we can't consume it.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I thought that having the skb either always on the ctx->rx_list
or ctx->recv_pkt will simplify the handling, as we would not
have to remember to flip it from one to the other on exit paths.
This became a little harder to justify with the fix for BPF
sockmaps. Subsequent changes will make the situation even worse.
Queue the skbs only when really needed.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
recvmsg() in TLS gets data from the skb list (rx_list) or fresh
skbs we read from TCP via strparser. The former holds skbs which were
already decrypted for peek or decrypted and partially consumed.
tls_wait_data() only notices appearance of fresh skbs coming out
of TCP (or psock). It is possible, if there is a concurrent call
to peek() and recv() that the peek() will move the data from input
to rx_list without recv() noticing. recv() will then read data out
of order or never wake up.
This is not a practical use case/concern, but it makes the self
tests less reliable. This patch solves the problem by allowing
only one reader in.
Because having multiple processes calling read()/peek() is not
normal avoid adding a lock and try to fast-path the single reader
case.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend SMC-R link group netlink attribute SMC_GEN_LGR_SMCR.
Introduce SMC_NLA_LGR_R_BUF_TYPE to show the buffer type of
SMC-R link group.
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On long-running enterprise production servers, high-order contiguous
memory pages are usually very rare and in most cases we can only get
fragmented pages.
When replacing TCP with SMC-R in such production scenarios, attempting
to allocate high-order physically contiguous sndbufs and RMBs may result
in frequent memory compaction, which will cause unexpected hung issue
and further stability risks.
So this patch is aimed to allow SMC-R link group to use virtually
contiguous sndbufs and RMBs to avoid potential issues mentioned above.
Whether to use physically or virtually contiguous buffers can be set
by sysctl smcr_buf_type.
Note that using virtually contiguous buffers will bring an acceptable
performance regression, which can be mainly divided into two parts:
1) regression in data path, which is brought by additional address
translation of sndbuf by RNIC in Tx. But in general, translating
address through MTT is fast.
Taking 256KB sndbuf and RMB as an example, the comparisons in qperf
latency and bandwidth test with physically and virtually contiguous
buffers are as follows:
- client:
smc_run taskset -c <cpu> qperf <server> -oo msg_size:1:64K:*2\
-t 5 -vu tcp_{bw|lat}
- server:
smc_run taskset -c <cpu> qperf
[latency]
msgsize tcp smcr smcr-use-virt-buf
1 11.17 us 7.56 us 7.51 us (-0.67%)
2 10.65 us 7.74 us 7.56 us (-2.31%)
4 11.11 us 7.52 us 7.59 us ( 0.84%)
8 10.83 us 7.55 us 7.51 us (-0.48%)
16 11.21 us 7.46 us 7.51 us ( 0.71%)
32 10.65 us 7.53 us 7.58 us ( 0.61%)
64 10.95 us 7.74 us 7.80 us ( 0.76%)
128 11.14 us 7.83 us 7.87 us ( 0.47%)
256 10.97 us 7.94 us 7.92 us (-0.28%)
512 11.23 us 7.94 us 8.20 us ( 3.25%)
1024 11.60 us 8.12 us 8.20 us ( 0.96%)
2048 14.04 us 8.30 us 8.51 us ( 2.49%)
4096 16.88 us 9.13 us 9.07 us (-0.64%)
8192 22.50 us 10.56 us 11.22 us ( 6.26%)
16384 28.99 us 12.88 us 13.83 us ( 7.37%)
32768 40.13 us 16.76 us 16.95 us ( 1.16%)
65536 68.70 us 24.68 us 24.85 us ( 0.68%)
[bandwidth]
msgsize tcp smcr smcr-use-virt-buf
1 1.65 MB/s 1.59 MB/s 1.53 MB/s (-3.88%)
2 3.32 MB/s 3.17 MB/s 3.08 MB/s (-2.67%)
4 6.66 MB/s 6.33 MB/s 6.09 MB/s (-3.85%)
8 13.67 MB/s 13.45 MB/s 11.97 MB/s (-10.99%)
16 25.36 MB/s 27.15 MB/s 24.16 MB/s (-11.01%)
32 48.22 MB/s 54.24 MB/s 49.41 MB/s (-8.89%)
64 106.79 MB/s 107.32 MB/s 99.05 MB/s (-7.71%)
128 210.21 MB/s 202.46 MB/s 201.02 MB/s (-0.71%)
256 400.81 MB/s 416.81 MB/s 393.52 MB/s (-5.59%)
512 746.49 MB/s 834.12 MB/s 809.99 MB/s (-2.89%)
1024 1292.33 MB/s 1641.96 MB/s 1571.82 MB/s (-4.27%)
2048 2007.64 MB/s 2760.44 MB/s 2717.68 MB/s (-1.55%)
4096 2665.17 MB/s 4157.44 MB/s 4070.76 MB/s (-2.09%)
8192 3159.72 MB/s 4361.57 MB/s 4270.65 MB/s (-2.08%)
16384 4186.70 MB/s 4574.13 MB/s 4501.17 MB/s (-1.60%)
32768 4093.21 MB/s 4487.42 MB/s 4322.43 MB/s (-3.68%)
65536 4057.14 MB/s 4735.61 MB/s 4555.17 MB/s (-3.81%)
2) regression in buffer initialization and destruction path, which is
brought by additional MR operations of sndbufs. But thanks to link
group buffer reuse mechanism, the impact of this kind of regression
decreases as times of buffer reuse increases.
Taking 256KB sndbuf and RMB as an example, latency of some key SMC-R
buffer-related function obtained by bpftrace are as follows:
Function Phys-bufs Virt-bufs
smcr_new_buf_create() 67154 ns 79164 ns
smc_ib_buf_map_sg() 525 ns 928 ns
smc_ib_get_memory_region() 162294 ns 161191 ns
smc_wr_reg_send() 9957 ns 9635 ns
smc_ib_put_memory_region() 203548 ns 198374 ns
smc_ib_buf_unmap_sg() 508 ns 1158 ns
------------
Test environment notes:
1. Above tests run on 2 VMs within the same Host.
2. The NIC is ConnectX-4Lx, using SRIOV and passing through 2 VFs to
the each VM respectively.
3. VMs' vCPUs are binded to different physical CPUs, and the binded
physical CPUs are isolated by `isolcpus=xxx` cmdline.
4. NICs' queue number are set to 1.
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces a new SMC-R specific element buf_type
in struct smc_link_group, for recording the value of sysctl
smcr_buf_type when link group is created.
New created link group will create and reuse buffers of the
type specified by buf_type.
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the sysctl smcr_buf_type for setting
the type of SMC-R sndbufs and RMBs.
Valid values includes:
- SMCR_PHYS_CONT_BUFS, which means use physically contiguous
buffers for better performance and is the default value.
- SMCR_VIRT_CONT_BUFS, which means use virtually contiguous
buffers in case of physically contiguous memory is scarce.
- SMCR_MIXED_BUFS, which means first try to use physically
contiguous buffers. If not available, then use virtually
contiguous buffers.
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some CPU, such as Xeon, can guarantee DMA cache coherency.
So it is no need to use dma sync APIs to flush cache on such CPUs.
In order to avoid calling dma sync APIs on the IO path, use the
dma_need_sync to check whether smc_buf_desc needs dma sync when
creating smc_buf_desc.
Signed-off-by: Guangguan Wang <guangguan.wang@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
smc_ib_sync_sg_for_cpu/device are the ops used for dma memory cache
consistency. Smc sndbufs are dma buffers, where CPU writes data to
it and PCIE device reads data from it. So for sndbufs,
smc_ib_sync_sg_for_device is needed and smc_ib_sync_sg_for_cpu is
redundant as PCIE device will not write the buffers. Smc rmbs
are dma buffers, where PCIE device write data to it and CPU read
data from it. So for rmbs, smc_ib_sync_sg_for_cpu is needed and
smc_ib_sync_sg_for_device is redundant as CPU will not write the buffers.
Signed-off-by: Guangguan Wang <guangguan.wang@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a third knob, '2', which extends the
accept_untracked_na option to learn a neighbor only if the src ip is
in the same subnet as an address configured on the interface that
received the neighbor advertisement. This is similar to the arp_accept
configuration for ipv4.
Signed-off-by: Jaehee Park <jhpark1013@gmail.com>
Suggested-by: Roopa Prabhu <roopa@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In many deployments, we want the option to not learn a neighbor from
garp if the src ip is not in the same subnet as an address configured
on the interface that received the garp message. net.ipv4.arp_accept
sysctl is currently used to control creation of a neigh from a
received garp packet. This patch adds a new option '2' to
net.ipv4.arp_accept which extends option '1' by including the subnet
check.
Signed-off-by: Jaehee Park <jhpark1013@gmail.com>
Suggested-by: Roopa Prabhu <roopa@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit e21145a987 ("ipv4: namespacify ip_early_demux sysctl knob") made
it possible to enable/disable early_demux on a per-netns basis. Then, we
introduced two knobs, tcp_early_demux and udp_early_demux, to switch it for
TCP/UDP in commit dddb64bcb3 ("net: Add sysctl to toggle early demux for
tcp and udp"). However, the .proc_handler() was wrong and actually
disabled us from changing the behaviour in each netns.
We can execute early_demux if net.ipv4.ip_early_demux is on and each proto
.early_demux() handler is not NULL. When we toggle (tcp|udp)_early_demux,
the change itself is saved in each netns variable, but the .early_demux()
handler is a global variable, so the handler is switched based on the
init_net's sysctl variable. Thus, netns (tcp|udp)_early_demux knobs have
nothing to do with the logic. Whether we CAN execute proto .early_demux()
is always decided by init_net's sysctl knob, and whether we DO it or not is
by each netns ip_early_demux knob.
This patch namespacifies (tcp|udp)_early_demux again. For now, the users
of the .early_demux() handler are TCP and UDP only, and they are called
directly to avoid retpoline. So, we can remove the .early_demux() handler
from inet6?_protos and need not dereference them in ip6?_rcv_finish_core().
If another proto needs .early_demux(), we can restore it at that time.
Fixes: dddb64bcb3 ("net: Add sysctl to toggle early demux for tcp and udp")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20220713175207.7727-1-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ensure that the fid's iounit field is set to zero when a new fid is
created. Certain 9P operations, such as OPEN and CREATE, allow the
server to reply with an iounit size which the client code assigns to the
p9_fid struct shortly after the fid is created by p9_fid_create(). On
the other hand, an XATTRWALK operation doesn't allow for the server to
specify an iounit value. The iounit field of the newly allocated p9_fid
struct remained uninitialized in that case. Depending on allocation
patterns, the iounit value could have been something reasonable that was
carried over from previously freed fids or, in the worst case, could
have been arbitrary values from non-fid related usages of the memory
location.
The bug was detected in the Windows Subsystem for Linux 2 (WSL2) kernel
after the uninitialized iounit field resulted in the typical sequence of
two getxattr(2) syscalls, one to get the size of an xattr and another
after allocating a sufficiently sized buffer to fit the xattr value, to
hit an unexpected ERANGE error in the second call to getxattr(2). An
uninitialized iounit field would sometimes force rsize to be smaller
than the xattr value size in p9_client_read_once() and the 9P server in
WSL refused to chunk up the READ on the attr_fid and, instead, returned
ERANGE to the client. The virtfs server in QEMU seems happy to chunk up
the READ and this problem goes undetected there.
Link: https://lkml.kernel.org/r/20220710141402.803295-1-tyhicks@linux.microsoft.com
Fixes: ebf46264a0 ("fs/9p: Add support user. xattr")
Cc: stable@vger.kernel.org
Signed-off-by: Tyler Hicks <tyhicks@linux.microsoft.com>
Reviewed-by: Christian Schoenebeck <linux_oss@crudebyte.com>
Signed-off-by: Dominique Martinet <asmadeus@codewreck.org>
Due to some changes and rebasing between different patches
this fell through the cracks; we need to set sta.mlo if the
connection is using MLO.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Unfortunately, a printk snuck into a previous patch,
remove it.
Fixes: 81151ce462 ("wifi: mac80211: support MLO authentication/association with one link")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
p9_req_put need to be called when m->rreq->rc.sdata is NULL to avoid
temporary refcount leak.
Link: https://lkml.kernel.org/r/20220712104438.30800-1-hbh25y@gmail.com
Fixes: 728356dede ("9p: Add refcount to p9_req_t")
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
[Dominique: commit wording adjustments, p9_req_put argument fixes for rebase]
Signed-off-by: Dominique Martinet <asmadeus@codewreck.org>
mempool prep commit removed the awkward kref usage which didn't
allow passing client pointer easily with the ref, so we no longer
need a separate function to remove the tag from idr.
This has the side benefit that it should be more robust in detecting
leaks: umount will now properly catch unfreed requests as they still
will be in the idr until the last ref is dropped
Link: https://lkml.kernel.org/r/20220712060801.2487140-1-asmadeus@codewreck.org
Signed-off-by: Dominique Martinet <asmadeus@codewreck.org>
Reviewed-by: Christian Schoenebeck <linux_oss@crudebyte.com>
While reading sysctl_tcp_probe_interval, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 05cbc0db03 ("ipv4: Create probe timer for tcp PMTU as per RFC4821")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_probe_threshold, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 6b58e0a5f3 ("ipv4: Use binary search to choose tcp PMTU probe_size")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_mtu_probe_floor, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: c04b79b6cf ("tcp: add new tcp_mtu_probe_floor sysctl")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_min_snd_mss, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
Fixes: 5f3e2bf008 ("tcp: add tcp_min_snd_mss sysctl")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_base_mss, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
Fixes: 5d424d5a67 ("[TCP]: MTU probing")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_mtu_probing, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
Fixes: 5d424d5a67 ("[TCP]: MTU probing")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_ip_autobind_reuse, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 4b01a96742 ("tcp: bind(0) remove the SO_REUSEADDR restriction when ephemeral ports are exhausted.")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_ip_nonlocal_bind, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_ip_fwd_update_priority, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its readers.
Fixes: 432e05d328 ("net: ipv4: Control SKB reprioritization after forwarding")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_ip_fwd_use_pmtu, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
Fixes: f87c10a8aa ("ipv4: introduce ip_dst_mtu_maybe_forward and protect forwarding path against pmtu spoofing")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_ip_no_pmtu_disc, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_ip_default_ttl, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
delay_timer has been unused since commit c3498d34dd ("cbq: remove
TCA_CBQ_OVL_STRATEGY support"). Delete it.
Signed-off-by: Peilin Ye <peilin.ye@bytedance.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It might seem a bit pointless to do a multi-link operation
connection with just a single link, but this is already a
big change, so for now, limit MLO connections to a single
link.
Extending that to multiple links will require
* work on parsing the multi-link element with STA profile
properly, including element fragmentation;
* checking the per-link status in the multi-link element
* implementing logic to have active/inactive links to let
drivers decide which links should be active;
* implementing multicast RX deduplication;
* and likely more.
For now this is still useful since it lets us do multi-link
connections for the purposes of testing APIs and the higher
layers such as wpa_supplicant.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the necessary API to parse the multi-link element in
the future. For now, link only to the element when found
so we can use it in the client-side code later.
Later, we'll need to fill this in to deal with element
fragmentation, parse the STA profile, etc.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In some cases, e.g. with Qualcomm devices and management
frames, or in hwsim, frames may be reported from the driver
with link addresses, but for decryption and matching needs
we really want to have them with MLD addresses. Support the
translation on RX.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When an MLO AP is transmitting to a non-MLO station, addr2 should be set
to a link address. This should be done before the frame is encrypted as
otherwise aad verification would fail. In case of software encryption
this can't be left for the device to handle, and should be done by
mac80211 when building the frame hdr.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we create a station with a non-default link, then
we should have a link address, and we definitely need
to insert it into the link hash table on insertion.
Split the API into with and without link creation and
if it has a link, insert the link into the link hash
table on sta_info_insert().
Fixes: ba6ddab94f ("wifi: mac80211: maintain link-sta hash table")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In AP/mesh where the stations are added by userspace, we
limit the number of A-MSDU subframes according to the
extended capabilities.
Refactor the code and extend that also to client-side.
Fixes: 506bcfa8ab ("mac80211: limit the A-MSDU Tx based on peer's capabilities")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Split out much of the code in ieee80211_set_associated()
into a new ieee80211_link_set_associated() which can be
called per link later for MLO.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a helper function cfg80211_get_iftype_ext_capa() to
look up interface type-specific (extended) capabilities.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If NEED_DTIM_BEFORE_ASSOC isn't set, then we don't need
to enter an RCU critical section and look up the beacon
elements.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Factor out the code to set up the assoc link into a
new function ieee80211_setup_assoc_link().
While at it, also modify the 'override' handling to
just take into account whether or not the conn_flags
were changed, which is what we need to setup again
the channel later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to pass the address, we can look at the auth_data
inside the function rather than outside.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Refactor the per-link setup out of ieee80211_assoc_success()
into a new function ieee80211_assoc_config_link().
It looks useless for now to parse the elements again inside
ieee80211_assoc_config_link(), but that will be done with
the link ID in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Refactor ieee80211_prep_channel() to make the link argument
optional and add a conn_flags pointer argument instead, so
that we can later use this for links that don't exist yet
to build the right information for MLO.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For MLO, we will need to build these elements per link, so
factor out the code that does this, returning the capability,
to simplify building the multi-link element in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With MLO, when we'll disconnect from an AP MLD, we'll just
destroy all the links. Therefore, the only thing we (may)
need to reset is the deflink data, so switch back to that
and adjust the comments accordingly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For MLO we'll need to read flags not directly from the link as
it may not even exist yet if we're just setting up flags for
a secondary link before sending the association request, so
pass the incoming conn_flags separately. Also, while at it,
pass the sdata/link separately as for non-tracking now the
link may be NULL.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We'll need ieee80211_prep_channel() in other code for MLO
later, so move the code up - unchanged for now - to avoid
forward declarations in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Refactor the code here since we need to have it also for each
link station after association in MLO later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The flag here is currently per interface, but the way we
set and clear it means it should be per link, so change
it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When sending an authentication frame from an MLD, include
the multi-link element with the MLD address and use the
link address for transmission.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Clean up the code building the supported channels element
a little bit by using a local variable instead of the long
line.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For now, prohibit DEAUTH_NEED_MGD_TX_PREP since we can't
really transmit this on a specific link yet as we don't
know which links are active.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The new NL80211_CMD_ADD_LINK_STA and NL80211_CMD_MODIFY_LINK_STA
commands have strict policy validation, so fix the policy so it
can be validated correctly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The underlying mac80211 code cannot deal with fragmented
elements for purposes of sorting the elements into the
association frame, so reject those inside the link. We
might want to reject them inside the assoc frame, but
they're used today for FILS, so cannot do that.
The non-inheritance element inside the links similarly
cannot be handled by mac80211, and outside the links it
makes no sense.
Reject both since using them could lead to an incorrect
implementation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we associate, we'll include all the elements for the
link we're sending the association request on in the frame
and the specific ones for other links in the multi-link
element container. Prohibit adding link-specific elements
for the association link.
Fixes: d648c23024 ("wifi: nl80211: support MLO in auth/assoc")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The link loop will always have a valid link so that
it's always set, but static checkers don't always
see that, so set it to NULL explicitly.
Fixes: efbabc1165 ("cfg80211: Indicate MLO connection info in connect and roam callbacks")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since struct ieee80211_bss_conf already contains link_id,
passing link_id is not necessary.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since mac80211 already has a protected pointer to link_conf,
pass it to the driver to avoid additional RCU locking.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
At least while we don't have any more specific interface
combinations support, add a simple flag for MLO support,
we can keep this later based on something other than the
wiphy flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Recalculate min channel context for the given or all interface
links, depending on the caller. For a station state change, we
need to recalculate all of them since we don't know which link
(or multiple) it might be on.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We check here that we don't enable TX (netif_carrier_ok())
before we actually start using some channel context, but to
our knowledge this check has never triggered, and with MLO
it's just wrong since links can be added and removed much
more dynamically than before.
Simply remove the checks, there's no really good way to do
anything that would replace them.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This simplifies hostapd implementation, since it didn't
switch to NL80211_CMD_SET_CHANNEL.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow link source address on TX.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow transmitting EAPOL frames not only from the interface
address (which is the MLD address) but also any link addresses,
in order to support non-MLO stations on AP interfaces.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case of authentication with a legacy station, link addressed EAPOL
frames should be sent. Support it.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Set the MLD parameters in NL80211_CMD_SET_STATION handling
to be able to change an MLD station.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We should check that MLO connections are supported before
attempting to authenticate with MLO parameters, check that.
Fixes: d648c23024 ("wifi: nl80211: support MLO in auth/assoc")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The way this works is that you add all the element data,
keeping a pointer to the length field of the element.
Then call this helper function, which will fragment the
element if there was more than 255 bytes in the element,
memmove()ing the data back if needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For now, skip rate statistics here to avoid warnings in
the called code, we'll need to adjust this to have all
the statistics for link stations.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the BSS lookup returned an error, set it to NULL so we
don't try to free it.
Fixes: d648c23024 ("wifi: nl80211: support MLO in auth/assoc")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We have the per-interface type capabilities, currently for
extended capabilities, add the EML/MLD capabilities there
to have this advertised by the driver.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we add a station on an MLD, we need a link ID to see
where it lives (by default). Validate the link ID against
the valid_links.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we add non-deflink pointers, we need to remove the
link[0] pointer to deflink in case link[0] is not valid
afterwards. Also, we need to add that back when there
are no more valid links. Reorg the code to fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we remove a link that doesn't have a channel context,
we don't really need the local->mtx locking. Tighten the
check here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This was missing earlier, we need to remove links when
interfaces are being destroyed, and we also need to
stop (AP) operations when a link is being destroyed.
Address these issues to remove many warnings that will
otherwise appear in mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We need to consider the (maximum) size of the EHT element
we'll add for the association request, otherwise we may run
out of space.
Fixes: 820acc810f ("mac80211: Add EHT capabilities to association/probe request")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The functions currently take a link and check data
from it, but this needs to change for MLO. Simplify
the prototypes by passing only the needed arguments.
Remove the regulatory checks, the warnings shouldn't
trigger, and haven't as far as I know.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Rework the sorting of custom elements into the association
request by moving the elements before HT/VHT/HE to each
their own function. While at it, fix the placement of the
ones that should be between VHT and HE.
This doesn't fix the placement of elements that should be
between HE and EHT yet, a similar change might be needed
in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's some awkward code that really only exists
because we want to optimize the allocation size,
but that's not really all that necessary.
Refactor the code that adds rates to the association
request frame to have a separate function, removing
the goto.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Here, ext_capa is checked and can only be non-NULL if
assoc_data->ie_len was set before, so the check here
is redundant.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We need to handle the link addresses for station differently,
they will be determined by the association code, stored, and
then applied when the links are actually created on success,
cfg80211 will fill in the right addresses per the data we're
sending back to it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When parsing a frame containing a multi-BSSID element, we
need to know both the transmitted and non-transmitted BSSID
so we can parse it correctly.
Unfortunately, in quite a number of cases, we got this wrong
and were passing the wrong BSSID or useless information:
* the mgmt->bssid from a frame is only the transmitted
BSSID if the frame is a beacon
* passing just one of the parameters as non-NULL isn't
useful and ignored
In those case where we need to parse for a specific BSS we
always have a BSS structure pointer, representing the BSS
we need, whether transmitted or not. Thus, pass that pointer
to the parsing function instead of the two BSSIDs.
Also fix two bugs:
* we need to re-parse all the elements for the other BSS
when iterating the non-transmitted BSSes in scan
* we need to parse for the correct BSS when setting up
the channel data in client code
Fixes: 78ac51f815 ("mac80211: support multi-bssid")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We're already passing the elems pointer, and have parsed
them from the same frame with exactly the same parameters,
so don't need to do that again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When calling start/stop_ap(), mac80211 already has a protected
link_conf pointer. Pass it to the driver, so it shouldn't
handle RCU protection.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Refactor the element parsing into a version that has
a parameter struct so we can add more parameters more
easily in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Extend the cfg80211_rx_assoc_resp() to cover multiple
BSSes, the AP MLD address and local link addresses
for MLO.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For MLO we'll need a lot more arguments, including all the
BSS pointers and link addresses, so move the data to a struct
to be able to extend it more easily later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We only report the BSSID to userspace, so change the
argument from BSS struct pointer to AP address, which
we'll use to carry either the BSSID or AP MLD address.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a few cases where we send an event to cfg80211
manually, but ieee80211_destroy_assoc_data() also handles
the case of abandoning; some cases don't need an event
and success is handled yet differently.
Unify this by providing a single status argument to the
ieee80211_destroy_assoc_data() function and then handling
all the different cases of events (or no events) there.
This will help simplify the code when MLO support is
added.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For MLO, we need the ability to report back multiple BSS
structures to release, as well as the AP MLD address (if
attempting to make an MLO connection).
Unify cfg80211_assoc_timeout() and cfg80211_abandon_assoc()
into a new cfg80211_assoc_failure() that gets a structure
parameter with the necessary data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The race described by the comment in mac80211 hasn't existed
since the locking rework to use the same lock and for MLO we
need to pass the AP MLD address, so just pass the BSSID or
AP MLD address instead of the BSS struct pointer, and adjust
all the code accordingly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For station capabilities, e.g. TWT, we need to use the correct
link station instead of deflink. Switch the code to do that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The argument is unused except for NULL checking, but we already
do that anyway, so it's not needed. Remove the argument.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This requires a few more changes.
While at it, also add a warning to ieee80211_get_sband()
to avoid it being used when there are multiple links.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we decide to stop tracking QoS/WMM parameters, then
this should be a per-link decision. Move the flag to
the link instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Do the first adjustments in the client-side code to pass
the link pointer (instead of sdata) to most places etc.
This is just preparation, so the real MLO patches become
smaller.
Note that this isn't complete, notably there are still
quite a few references to sta->deflink and sta->sta.deflink.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove the IEEE80211_STA_RESET_SIGNAL_AVE flag and use
a bool instead, but invert the polarity (now calling it
tracking_signal_avg) so we don't have to initialize it,
and put that into the link instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To prepare a bit more for MLO in the client code,
track the AP's address (for now only the BSSID, but
will track the AP MLD's address later) separately
from the per-link BSSID.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In MLO, expect the driver fully handles powersave handling,
including tracking whether or not a beacon was received,
the DTIM period, etc.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This really shouldn't be in a per-link config, we don't want
to let anyone control it that way (if anything, link powersave
could be forced through APIs to activate/deactivate a link),
and we don't support powersave in software with devices that
can do MLO.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It might be useful to drivers to be able to pass only the
link_conf pointer, rather than both the pointer and the
link_id; add the link_id to the link_conf to facility that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In station/client mode, the link data needs a bit more
initialization and destruction than just zero-init and
kfree() respectively, implement that.
This required some shuffling of the link data handling
in general, as we should set it up in setup and do the
teardown in teardown, otherwise we're asymmetric in
case of interface type changes.
Also stop using kfree_rcu(), we cannot guarantee that
nothing is scheduling things that live within the link
(e.g. the u.mgd.request_smps_work) until we're sure it
cannot be referenced anymore, therefore synchronize
instead. This isn't very efficient, but we can always
optimize it later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
At least the quantenna driver calls wdev_chandef() here
which now requires the lock, so acquire it.
Fixes: 7b0a0e3c3a ("wifi: cfg80211: do some rework towards MLO link APIs")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With the split into keys[]/deflink.gtk[] arrays, WEP keys are
still installed into the keys[] array, but we didn't look them
up there. This meant they weren't deleted correctly.
Fix this by looking up the key there even if it's not pairwise
so we can be sure we don't have it.
Fixes: bfd8403add ("wifi: mac80211: reorg some iface data structs for MLD")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Separate out the connection downgrade flags from the ifmgd->flags
and put them into the link information instead. While at it, make
them a separate sparse type so we don't get confused about where
they belong and have static checking on correct handling.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Align the mac80211 implementation with P802.11be_D1.5.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a few places that check ps_sdata and/or the dynamic
PS timeout, but they're erroneous in case SUPPORTS_DYNAMIC_PS
is set by the driver.
Skip the entire recalculation in this case so we cannot get
into those paths elsewhere, and so we simplify this for the
purpose of implementing MLO.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we don't really have multiple links, omit the link ID from
link debug prints, otherwise we change the format for all of
the existing drivers (most of which might never support MLO),
and also have extra noise in the logs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For multi-link operation, this cannot work as the req->bss pointer
will be NULL, and we'll need to do more work on this to really add
tracing for the MLO case here. Drop the BSS elements for now as
they're not the most useful thing, and it's hard to size things
correctly for the MLO case (without adding a lot of code that's
also executed when tracing isn't enabled.)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since for an MLD station the default link is added together
with the add station command, allow also setting the link
MAC address.
Otherwise, it is needed to use the modify link API only
for setting the link MAC address.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since links can be added and removed dynamically, we need to
somehow protect the sdata->link[] and vif->link_conf[] array
pointers from disappearing when accessing them without locks.
RCU-ify the pointers to achieve this, which requires quite a
bit of rework.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since this will need to refer - at least in part - to the link
stations of an MLD, hold the wdev mutex for driver convenience.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
